StarTech.com BOX4CABLE User Manual
Displayed below is the user manual for BOX4CABLE by StarTech.com which is a product in the Cable Organizers category. This manual has pages.
Related Manuals
Manual Revision: 12/01/2016
For the latest information, technical specications, and support for
this product, please visit www.startech.com/BOX4CABLE
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
BOX4CABLE
Cable Access Box for Conference Tables
*actual product may vary from photos
Instruction manual
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders. PHILLIPS® is a registered trademark of Phillips Screw Company in the
United States or other countries.
Instruction manual
i
Table of Contents
Introduction ......................................................................................................... ii
Top view ....................................................................................................................................................... 1
Side view ...................................................................................................................................................... 1
Bottom view ................................................................................................................................................ 1
Package contents ...................................................................................................................................... 2
Requirements ............................................................................................................................................. 2
Cable installation ................................................................................................ 2
In-table installation ........................................................................................... 3
Technical support ............................................................................................... 5
Warranty information ....................................................................................... 5
Instruction Manual
ii
Introduction
This cable-access box installs into your conference-room table or podium to provide
an in-surface panel that conceals your AV, network or charging cables when they’re not
in use.
When you need to access one of the cables, you can simply rotate the cover panel
open and pull out your desired cable.
When you’re nished, you can easily slide the cable back into the box. The access holes
at the bottom of the panel are engineered to let gravity do all of the work, seamlessly
guiding your cables back and concealing the length of the cable below the surface of
your table.
External view
Internal view
Instruction manual
1
Cover Panel
Mounting bracket slots
Panel screws
Cable routing panels
Cable holes
Instruction Manual
2
Package contents
• 1 x cable access box
• 2 x mounting brackets with screws and wingnuts
• 4 x large nylon split bushings
• 7 x small nylon split bushings
• 1 x diecut outline
• 1 x quick-start guide
Requirements
• A table surface for installation.
• Up to nine cables for routing through the box.
• A Phillips head screw driver.
• A saw or other cutting tool.
Cable installation
1. Using a Phillips head screwdriver (sold separately) remove the panel screws from
either side of the cable routing panels that contain the hole(s) you’d like to occupy
with the cable(s).
2. Remove the cable routing panel by sliding the screwdriver into one of the cable
holes and prying the cable panel up.
3. Slide your cable(s) into any available cable hole(s) that match the width of your
cable(s). Be sure to place thicker cables in the larger holes and thinner cables into
the smaller holes.
4. Place the cable routing panel back into it’s slot and replace the screws.
5. Inside the box, wrap the large nylon split bushing(s) (included) around the
larger cable(s) and the small nylon split bushing(s) (included) around the smaller
cable(s).
6. Slide each of the nylon split bushings into the cable hole.
Repeat steps 1 through 5 to install additional cables using the other cable panel.
Instruction manual
3
In-table installation
1. Using the included die-cut outline, trace the inner square on the table surface in
your desired location.
2. Carefully cut the square out of the table surface.
Note: StarTech.com is not responsible for any damage to your table surface.
3. Slide the cable box into the square hole in your table surface.
Instruction Manual
4
4. Under the table surface, on either side of the cable box, hook each of the mounting
brackets into one of the three mounting bracket slots, depending on which aligns
closest to the table.
5. Hand tighten the wing nuts to secure the cable box to your table.
Instruction manual
5
Technical support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty information
This product is backed by a two-year warranty.
StarTech.com warrants its products against defects in materials and workmanship
for the periods noted, following the initial date of purchase. During this period,
the products may be returned for repair, or replacement with equivalent
products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.