StarTech.com DKT30CHVPD2 User Manual
Displayed below is the user manual for DKT30CHVPD2 by StarTech.com which is a product in the Interface Hubs category. This manual has pages.
Related Manuals
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: February 8, 2021
12
3
4
5
6
Product Diagram (DKT30CHVPD2)
Front Angle View
Rear View
Port Specications and Installation
1VGA Output Port
• Resolution of up to 1920x1080@60Hz
• Connect the Multiport Adapter to a VGA Display
Device, using a VGA M/M Cable
2HDMI Output Port
• HDMI 1.4b
• 4K @ 30Hz
• Connect the Multiport Adapter to an HDMI Enabled
Display Device, using an HDMI Cable
USB-C™ Multiport Adapter - HDMI & VGA - 3 x USB - GbE- 100W PD - Extended Cable
3RJ45 Port
• 10/100/1000 Mbps
• Connect the Multiport Adapter to a Network Device,
using a Network Cable
4USB-A Charging Port
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• Maximum 1.5A for downstream charging
• Connect the Multiport Adapter to a SuperSpeed USB
5Gbps Peripheral or Storage Device (e.g. ash drive),
using a SuperSpeed USB 5Gbps (USB 3.2
Gen 1) Cable
5USB-C Device Port
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• USB Power Delivery (PD) pass-through
• Connect the Host Computer’s Power Adapter
to the SuperSpeed USB-C Port on the Multiport
Adapter for a maximum of 85W delivered to the
Host Computer
Note: The Multiport Adapter accepts a 100W Power
Adapter and reserves 15W to power the Multiport
Adapter.
-- Or --
• Connect the Multiport Adapter to a SuperSpeed USB
5Gbps Peripheral or Storage Device (e.g. ash drive),
using a SuperSpeed USB-C 5Gbps (USB 3.2
Gen 1) Cable
6USB-C Host
Connector
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• USB PD 3.0 85W (20V/5A)
Note: SuperSpeed USB-C Port will accept up to
100W Power Source input
• DP 1.2 Alt Mode
• Charge the Host Device while using the Multiport
Adapter
• Connect the Multiport Adapter to a to a Laptop,
using the SuperSpeed USB-C Host Connector
7USB-A Device Port
• SuperSpeed USB 5Gbps (USB 3.2 Gen 1)
• Maximum 900mA downstream charging
• Connect the Multiport Adapter to a SuperSpeed USB
5Gbps Peripheral or Storage Device (e.g. ash drive),
using a SuperSpeed USB 5Gbps (USB 3.2
Gen 1) Cable
7
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
iPad Pro® is a trademark of Apple Inc., registered in the U.S. and other countries.
Warranty Information
This product is backed by a three-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
Requirements
For the latest requirements, please visit:
www.startech.com/DKT30CHVPD2.
• Host Computer with USB-C Port
• DP-Alt Mode Compatible
• USB PD Support
Installation
Notes: Installation is automatic for all modern Operating Systems. If the drivers do not
auto-install, please visit www.startech.com/DK30CHVPD2 to locate the latest drivers.
Operation
RJ45 Port LED Indicators
LED Color Status Indication
Orange/
Amber
Solid • Link speed is either 1000Mbps (1 GbE), 100Mbps, or
10Mbps
O • No connection established
White Flashing • Network trac detected
O • No link established