Table of Contents
StarTech.com FPWMNB User Manual
Displayed below is the user manual for FPWMNB by StarTech.com which is a product in the Signage Display Mounts category. This manual has pages.
Related Manuals
1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ
い。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に
従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
Warning Statements
• Make sure to assemble this product according to the instructions. Failure to
do so might result in personal injury or property damage.
• Make sure that the weight of the TV doesn’t exceed the weight capacity
of this product. If you exceed the weight capacity, you might experience
personal injury or damage to the equipment. This product can support the
following total weight: Up to 150 kg (330 lb.).
• Never operate this product if parts are missing or damaged.
• The wall mount is designed to be installed on a wood stud, solid concrete,
or cinder block wall. The wall structure should also be capable of supporting
at least four times the weight of the mounted equipment. The mounting
hardware included with this product may not be adequate for installation on
certain wall structures. Failure to comply with these warnings may result in
personal injury or damage to the equipment.
• The mounting hardware included with this product might not be adequate
for some wall structures. If you lack the necessary expertise to attach this
product to the wall structure that you’re using, contact a construction
professional to install the wall mount or to provide specic mounting
instructions for your wall structure.
Dichiarazioni di avvertenza
• Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle
istruzioni potrebbe causare danni a persone o proprietà.
• Vericare che il peso del monitor non superi la capacità di supporto del
prodotto. In caso di superamento della capacità di supporto potrebbero
vericarsi danni a persone o apparecchiature. Il prodotto è in grado di
supportare i seguenti pesi: 150 kg.
• Non utilizzare il prodotto in presenza di parti mancanti o danneggiate.
• Le caratteristiche dei muri sono variabili ed è importante vericare che
la struttura muraria e l’hardware di montaggio in uso siano in grado di
supportare adeguatamente le apparecchiature montate. Il mancato rispetto
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
delle istruzioni potrebbe causare danni a persone o proprietà. La struttura
muraria deve essere in grado di supportare un peso almeno quattro volte
superiore a quello dell’apparecchiatura montata.
• L’hardware di montaggio incluso con il prodotto potrebbe non essere
adeguato ad alcune strutture murarie. Se l’utente non dispone delle
competenze necessarie per agganciare il prodotto alla struttura muraria
in uso, dovrà contattare un professionista edile per installare il supporto a
parete o ottenere istruzioni di montaggio per la struttura muraria in uso.
Avertissements
• Assemblez ce produit conformément aux instructions. Si vous ne respectez
pas ces instructions, vous risquez de vous blesser ou d’endommager
l’équipement.
• Vériez que le poids du moniteur ne dépasse pas la capacité pondérale du
produit. Si vous dépassez la capacité pondérale, vous risquez des blessures
corporelles ou des dommages matériels. Ce produit peut supporter de 150
kg.
• N’utilisez pas ce produit si des pièces sont endommagées ou manquantes.
• Les structures des murs varient. Vous devez impérativement vérier que
le type de mur et le matériel de xation que vous utilisez permettent de
soutenir correctement l’équipement. Dans le cas contraire, vous risquez des
blessures corporelles ou des dommages matériels. La structure du mur doit
pouvoir supporter au moins quatre fois le poids de l’équipement monté.
• Le matériel de xation inclus avec ce produit n’est pas forcément approprié
pour toutes les structures de murs. Si vous ne disposez pas des compétences
nécessaires pour installer ce produit au mur, contactez un professionnel
an qu’il installe le support mural ou qu’il vous fournisse les instructions de
montage spéciques à votre structure de mur.
Warnhinweise
• Montieren Sie dieses Produkt gemäß den Anweisungen. Anderenfalls kann
dies zu Verletzungen von Personen oder Schäden an Eigentum führen.
• Das Gewicht des Monitors darf die zulässige Traglast des Produkts nicht
übersteigen. Wenn die Traglast überschritten wird, kann dies zu Verletzungen
von Personen oder Schäden an Geräten führen. Dieses Produkt ist für
folgendes Gewicht geeignet: 150 kg.
• Das Produkt darf nicht bedient werden, wenn Teile fehlen oder beschädigt
sind.
• Wandstrukturen unterscheiden sich, und es muss sichergestellt werden,
dass die Wand und das verwendete Montagematerial das montierte Gerät
halten kann. Anderenfalls kann dies zu Verletzungen von Personen und/oder
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Schäden an Geräten führen. Die Wand muss mindestens das Vierfache des
Gewichts des montierten Geräts halten können.
• Das mitgelieferte Montagematerial ist möglicherweise nicht für jede Wand
geeignet. Wenn Ihnen die nötigen Fachkenntnisse zum Anbringen dieses
Produkts an einer Wand fehlen, lassen Sie einen Fachmann den Wandhalter
anbringen, oder lassen Sie sich von einem Fachmann Montageanweisungen
für Ihre Wand erteilen.
Waarschuwingen
• Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit
niet goed gebeurt kan lichamelijk letsel of materiële schade ontstaan.
• Zorg dat het gewicht van het scherm de maximale capaciteit van dit product
niet overschrijdt. Als u de gewichtscapaciteit overschrijdt, kan persoonlijk
letsel of schade aan de apparatuur ontstaan. Dit product ondersteunt het
volgende gewicht: 150 kg.
• Gebruik dit product nooit als er onderdelen ontbreken of beschadigd zijn.
• Omdat wanden verschillen, is het belangrijk dat u ervoor zorgt dat het type
wandstructuur en de montagemiddelen die u gebruikt de gemonteerde
apparatuur goed ondersteunen. Indien u dit niet doet kan lichamelijk
letsel en/of schade aan de apparatuur ontstaan. De wandstructuur moet
voldoende zijn om ten minste vier keer het gewicht van de gemonteerde
apparatuur te ondersteunen.
• De bij dit product geleverde montagemiddelen kunnen niet geschikt zijn
voor sommige wandstructuren. Als u onvoldoende kennis hebt om dit
product aan de door u gebruikte wandstructuur te bevestigen, neem dan
contact op met een bouwkundige om de steun aan de muur te installeren of
specieke montage-instructies voor uw wandstructuur te geven.
Varningsmeddelanden
• Se till att du monterar produkten i enlighet med instruktionerna. Om du inte
gör det kan skada på person eller egendom uppstå.
• Se till att skärmens vikt inte överstiger produktens viktkapacitet. Om
viktkapaciteten överstigs kan skada på person eller utrustning uppstå. Denna
produkt har stöd för följande vikter: 150kg.
• Använd aldrig produkten om delar saknas eller är skadade.
• Eftersom väggstrukturer varierar är det viktigt att kontrollera att
väggstrukturen och monteringsutrustningen som du använder klarar av
den monterade utrustningen. Om du inte gör det kan skada på person och/
eller utrustning uppstå. Väggstrukturen ska kunna klara av minst fyra gånger
vikten av den monterade utrustningen.
6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
• Monteringsutrustningen som medföljer produkten kanske inte är lämplig
för vissa väggstrukturer. Om du saknar nödvändiga kunskaper för att
fästa denna produkt på väggstrukturen som du använder, kontakta en
professionell konstruktör för att installera väggmonteringen eller för att ge
specika monteringsinstruktioner för din väggstruktur.
Mensagens de aviso
• Certique-se de que monta este produto de acordo com as instruções.
O incumprimento pode resultar em ferimentos pessoais ou danos de
propriedade.
• Certique-se de que o peso do monitor não excede a capacidade de peso
deste produto. Se exceder a capacidade de peso, pode sofrer ferimentos
pessoais ou danos no equipamento. Este produto pode suportar o seguinte
peso: 150 kg.
• Nunca opere este produto se faltarem peças ou estas estiverem danicadas.
• As estruturas de parede variam e é importante certicar-se de que o tipo de
estrutura de parede e hardware de montagem que está a usar irá suportar
devidamente o equipamento montado. O incumprimento pode resultar
em ferimentos pessoais e/ou danos no equipamento. A estrutura de parede
deve ser capaz de suportar pelo menos quatro vezes o peso do equipamento
montado.
• O hardware de montagem incluído com este produto pode não ser
adequado para algumas estruturas de parede. Se não tiver o conhecimento
necessário para xar este produto à estrutura de parede que está a usar,
contacte um prossional de construção para fazer a instalação em parede ou
para fornecer instruções de montagem especícas para a sua estrutura de
parede.
Advertencias de uso
• Asegúrese de ensamblar este producto según las instrucciones. De lo
contrario, pueden producirse lesiones personales o daños en la propiedad.
• Asegúrese de que el peso del monitor no exceda la capacidad de carga de
este producto. Si se excede dicha capacidad se podrían producirse lesiones
personales o daños al equipo. Este producto tiene la siguiente capacidad de
carga: 150 kilogramos.
• Nunca opere o ponga en funcionamiento este producto si faltan piezas o hay
daños en las mismas.
• Las estructuras de las paredes pueden variar y, por tanto, es importante
determinar con certeza que el tipo de estructura de la pared y el hardware
de montaje que se va a utilizar puedan soportar debidamente el equipo. De
lo contrario, se pueden producir lesiones personales o daños en el mismo. La
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
estructura de la pared debe ser capaz de soportar al menos cuatro veces el
peso del componente instalado.
• El hardware de montaje incluido con este producto puede no ser adecuado
para algunas estructuras de pared. Si no tiene la experiencia suciente para
jar este producto a la estructura de la pared correspondiente, póngase en
contacto con un profesional de la construcción para instalar el soporte de
pared o para que le proporcione las instrucciones especícas de montaje
para su estructura de pared.
注意
• 必ず取扱説明書に従って本製品の組み立てを行って下さい。
• 最初に取扱説明書を最後まで読み、本製品の組み立て方をすべて理解し
てから組み立て作業を始めて下さい。
• 本製品は、室内での使用を想定しています。戸外では使用しないで下さ
い。
• 本製品は、二人がかりでの組み立てを想定しています。手助けなしに単独
で組み立てと設置を行わないで下さい。
• モニタの重量が本製品の最大積載重量を超えないようにして下さい。最
大積載重量をオーバーした場合、怪我をする恐れや器物破損の恐れがあ
ります。モニタアームの耐荷重：150kg.キーボードトレイの耐荷重
• 壁面の構造は建物によって異なります。壁面の構造や使用する取り付け
金具が設置する装置を適切に支えられるかどうか、必ず確認してくださ
い。この注意を怠ると、怪我をする恐れや器物破損の恐れがあります。設
置する装置の少なくとも4倍の重量に耐えられる壁面構造が必要となり
ます。
• 壁面の構造によっては、本製品に付属の取り付け金具では十分な強度が
得られないことがあります。ご使用の壁面に適切に設置できるか判断し
かねる場合は、内装工事の専門業者にお問い合わせの上、本製品の壁面
設置を依頼するか、特定の壁面に適した設置方法について助言を受けて
ください。
• 反動注意！本製品には、リフト機構が組み込まれており、積載した装置を取
り外すと反動で急激に上昇する可能性があります。装置を取り外す前に、
本製品を最も高い位置に移動させて下さい。この操作を怠ると怪我をす
る恐れや器物破損の恐れがあります。
8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Safety Statements ..................................................................................2
Warning Statements ..............................................................................3
Product Diagram ....................................................................................9
Product Information ..............................................................................10
Package Contents .....................................................................................................................................10
Requirements ............................................................................................................................................. 13
Assembly .................................................................................................14
Connecting Wall Plates............................................................................................................................ 14
Installing the Adapter Brackets ............................................................................................................ 16
Spacer Combination ................................................................................................................................20
Mounting ................................................................................................. 20
Mounting the Display .............................................................................................................................. 21
Adjusting .................................................................................................23
Adjusting the Display Tilt ....................................................................................................................... 23
9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
1Adapter Bracket 3Small Wall Plate
2Wall Plate 4Wall-Plate Clamps
10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
Wall Plates
Qty: Four
Small Wall Plate
Qty: One
Adapter Brackets
Qty: Six
Wall-Plate Clamps
Qty: Eight
11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Locking Pins
Qty: Six
M4x6 mm Screws
Qty: Sixteen
M5x14 mm Screws
Qty: Twelve
M6x14 mm Screws
Qty: Twelve
M6x30 mm Screws
Qty: Twelve
M8x30 mm Screws
Qty: Twelve
12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
M8x50 mm Screws
Qty: Twelve
Plate Washers
Qty: Twelve
Small Spacers
Qty: Twenty Four
Large Spacers
Qty: Twenty Four
ST6.3x55 mm Screws
Qty: Eighteen
Concrete Anchors
Qty: Eighteen
13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
D6 Washers
Qty: Eighteen
5 mm Hex Key
Qty: One
Requirements
• Level x 1
• Writing Utensil x 1
• Drill x 1
• Phillips Head Screwdriver x 1
• Ladder x 1
14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Assembly
Connecting Wall Plates
If the combined width of the Displays is less than 1 m (39.37
“) you can connect the Wall Plates together without using the
Small Wall Plate.
1. On a at surface, align the four Wall Plates side by side so
that the Wall Plates are touching.
Wall Plates
2. Using a Wall-Plate Clamp, slide the clamp around the lip
on two adjacent Wall Plates while aligning the two Screw
Holes on the Wall-Plate Clamp with the Screw Hole on
each of the Wall Plates.
Aligning the Wall Plate Clamp
15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3. Insert two M4x6 mm Screws through the Screw Holes on
the Wall-Plate Clamp and into the Screw Holes on the Wall
Plates.
4. Using the Phillips Head Screwdriver tighten the M4x6 mm
Screws.
5. Repeat steps 2 - 4 to install the remaining ve Wall-Plate
Clamps.
If the combined width of the Displays is greater than 1 m (39.37
“) you must use the Small Wall Plate when connecting the Wall
Plates together.
6. On a at surface, align the four Wall Plates and the Small
Wall Plate side by side so that the wall plates are touching,
with the Small Wall Plate in the middle.
Wall Plates with Small Wall Plate in the Middle
7. Repeat Steps 2 - 4 to install the remaining seven Wall-Plate
Clamps.
16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installing the Adapter Brackets
The TV Wall Mount supports the following VESA mounting
Patterns:
VESA Mount Patterns
200x200 300x200
400x200 400x300
300x300 400x400
600x400
Flat Back Display
When installing the Adapter Brackets on the Displays make
sure that the Locking Pins are in the 0-degree position (which
is the rst tilt position).
0-Degree Position
1. Determine the depth and diameter of the Mounting Holes
located on the back of the Display.
17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Align the Mounting Holes on the Adapter Brackets with
the Mounting Holes on the back of the Display.
Note: Make sure that the Arrow on each of the Adapter
Brackets is pointing up (toward the top of the Display).
Align Adapter Bracket with the Display’s Mounting Holes
3. Align the Plate Washer with the Mounting Holes on the
Adapter Bracket.
4. Insert the M8x50 mm, M6x30 mm, or M8x30 mm Screws
(depending on the hardware requirement), through the
Plate Washers, Adapter Brackets, and into the Display.
18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installing the Plate Washer
5. Using a Phillips Head Screwdriver, tighten the screws. Do
not over-tighten the screws.
Note: If you encounter resistance while tightening the
screws, stop. Failure to do so may result in damages to the
Display.
Recessed Mounting
1. Determine the depth and diameter of the Mounting Holes
located on the back of the Display.
2. Once you determine the correct depth and diameter of the
hardware needed, place the Spacers over the Screw Holes
on the back of the Display.
Note: Refer to the Spacer Combination table (p. 20) for dier-
ent hardware combinations.
3. Align one of the Adapter Brackets with the Spacers. Place
a Plate Washer over the Screw Holes on the Adapter
Bracket.
19
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
4. Insert the M8x50 mm, M6x30 mm, or M8x30 mm Screws
(depending on the hardware requirement), through the
Plate Washers, Adapter Brackets, Spacers and into the
Display.
Installing the Plate Washer and Spacer
5. Use a Phillips Head Screwdriver to tighten the screws. Do
not over-tighten the screws.
Note: Do not over-tighten the screws. If you encounter resis-
tance while tightening the screws, stop tightening. Failure to
do so could result in damage to the Display.
20
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Spacer Combination
Screw Type Spacer Combination
M6x30 mm
M8x30 mm
M8x50 mm
Mounting
Notes: Product mounting should be completed by a certi-
ed professional as per the local safety and building code
guidelines.
Wall structures vary, and it’s important to make sure that the
type of structure and mounting hardware that you’re using
will properly support the mounted equipment. Failure to do
so may result in personal injury and/or equipment damage.
21
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
1. Before installing the Wall Mount on the mounting surface,
contact a professional.
2. After consulting a professional, the TV Wall Mount can be
mounted using the included Mounting Hardware.
Mounting the Display
Warnings! Make sure that the weight of all three Displays
doesn’t exceed the weight capacity of this product. This prod-
uct can support a maximum weight of 150 kg (330 lb.), 50 kg
(110 lb.) per Display.
This product can support a maximum of three 50 inch Dis-
plays.
Attaching the Displays is a two-person job. Do not attempt
to complete this task by yourself.
1. Carefully lift the Display and slightly tilt the top of the
Display toward the mounting surface. Hook the top of both
Adapter Brackets (at the same time) onto the top edge of
the Wall Plate.
2. Once the tops of the Adapter Brackets are secured in place,
gently lower the bottom of the Display until the bottoms of
the Adapter Brackets come in contact with the Wall Plate.
3. While supporting the weight of the Display, slide the
Display across the Wall Plate until it is in the desired
position.
Note: Two people are required for making adjustments to
the Display.
22
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
4. While one person supports the Ladder, using the 5 mm Hex
Key, adjust the Height-Adjustment Screw located on the
top of the Adapter Bracket, until the Display is level.
Note: Micro-adjustments can cause the Display to shift
laterally along the Wall Bracket.
Height-Adjustment Screw
5. Using a Phillips Head Screwdriver tighten the two screws
located at the bottom of the Adapter Brackets, to secure
the Adapter Brackets to the Wall Plate. Do not over-tighten
the screws.
Note: If you encounter resistance while tightening the
screws, stop. Failure to do so may result in damages to the
Wall Bracket.
23
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Securing the Adapter Brackets to the Wall Plate
Adjusting
Adjusting the Display Tilt
The two Locking Pins on either side of the Adapter Bracket
are used to adjust the tilt of the Display from 0 to (-20) degrees.
Note: Two people are required for making adjustments to
the Display.
1. While one person supports the weight of the Display,
carefully pull out each of the Locking Pins located on either
side of the Adapter Bracket.
2. Adjust the tilt of the Display while aligning the Adjustment
Holes on the Adapter Bracket. The Adjustment Holes start
24
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
at 0-degrees and end at the natural position (-20) with no
Locking Pin installed.
Adjustment Positions
25
Warranty Information
This product is backed by a ve-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or
their ocers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of
prots, loss of business, or any pecuniary loss, arising out of or related to the use
of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
25
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle
15 Gowerton Rd.,
Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support