StarTech.com HSB220SAT25B User Manual
Displayed below is the user manual for HSB220SAT25B by StarTech.com which is a product in the Drive Bay Panels category. This manual has pages.
Related Manuals
Manual Revision: 05/19/2016
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
HSB220SAT25B
Rev 1
2 Drive 2.5in Trayless Hot Swap SATA
Mobile Rack Backplane
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................ 1
Features ........................................................................................................................................................ 1
Packaging Contents ................................................................................................................................. 1
Installation and Usage...........................................................................2
Hardware Installation ..............................................................................................................................2
Drive Installation ....................................................................................................................................... 3
Drive Removal ............................................................................................................................................ 5
Specications .......................................................................................... 6
Technical Support ..................................................................................7
Warranty Information ............................................................................ 7
Instruction Manual
1
Introduction
Thank you for purchasing a StarTech.com 3.5” Dual SATA Hard Drive Hot-Swap Bay -
the ideal solution for simplifying drive removals and insertions as part of the system
building process. Also a perfect addition for operating system image deployment and
any task that requires being able to quickly access large volumes of data on the y, the
HSB220SAT25B Dual SATA Hard Drive Hot-Swap Bay provides everything you need to
expedite important projects.
Features
• Driverless operation, tool-less hard drive installation
• Supports Hot Swapping
• Supports data transfer rates of up to 6.0 Gbps (SATA III), 3Gbps (SATA II),
and 1.5Gbps (SATA I)
• Swinging, latchable door simplies drive insertion and removal
Packaging Contents
• 1 x dual SATA hot-swap bay
• 2 x LP4 to SATA and LED adapter cable
• 1 x 15-pin SATA power and LED Y cable
• 2 x 7-pin SATA data cable
• 2 x hard drive protector lm
• 1 x screw kit
• 1 x instruction manual
Instruction Manual
2
Installation and Usage
Hardware Installation
To prepare HSB220SAT25B for installation within the computer:
1. Connect the 15-pin SATA Power Connector and 4-pin LED connector (provided
by an included LP4-to-4-pin LED/15-pin SATA Power Y-cable) to the appropriate
ports on the rear panel of HSB220SAT25B, as shown above.Repeat this
connection with the second (included) Y-cable, connecting to the remaining
ports on the rear panel of HSB220SAT25B.
2. Connect one end of a SATA Data Cable (provided) to each of the SATA Data ports
on the HSB220SAT25B rear panel.
(4-pin) LED
Connector
(7-pin) SATA Data
Connector
(15-pin) SATA Power
Connector
Instruction Manual
3
3. Ensuring the computer is powered down, remove the slot cover from a 3.5” oppy
drive bay on the host computer.
4. Gently, slide HSB220SAT25B into the now vacant 3.5” oppy drive bay, threading the
connected cables through the opening, until the front panel of HSB220SAT25B is
ush with the computer case front panel.
5. Make sure the screw slots located on the side panels of HSB220SAT25B are
aligned with the screw holes provided by the computer drive bay, then secure
HSB220SAT25B to the computer drive bay using the provided screws.
6. Connect both of the LP4 connectors provided by the Y-cables (see steps #1, #4) to
LP4 connectors provided by the computer power supply.
7. Connect the remaining ends of the SATA Data cables to the appropriate ports on
the computer motherboard. You may want to make note of which SATA ports
are used on the motherboard, in relation to their location on the rear panel of
HSB220SAT25B.
Drive Installation
Once HSB220SAT25B has been secured within the computer casing, and connected
appropriately:
1. Open the front panel doors by gently sliding the locking button from left to right,
then gently pull the door outward (exposing the drive bay):
Instruction Manual
4
Please note: It is essential that the drive be positioned properly within the drive bay.
Attempting to install a drive with its interface improperly aligned with the drive bay
interface could cause serious damage to both the drive and the drive bay.
2. Position a 2.5” SATA hard drive so that the SATA interface is directed into one of the
drive bays, label side up. Gently press the drive inward until the front panel door
begins to close, then lock the drive in place by closing the door until it clicks shut.
Repeat this procedure to install a second 2.5” SATA drive, into the remaining bay:
Instruction Manual
5
Please note: It is strongly recommended that the computer be powered down when
removing drives from HSB220SAT25B, as removing drives while in use can damage the
drive and any data contained within.
Drive Removal
To remove a drive from HSB220SAT25B:
1. Open the front panel door by gently sliding the locking button from left
to r ight.
2. Gently pull the door open to eject the drive partially, then pull the drive
out from the enclosure:
3. Once the drive is fully removed from the drive bay, swing the door
closed until it locks in place to prevent damage to the door/hinge.
Similarly, the closed door will help prevent dust particles from entering
the computer.
Instruction Manual
6
Specications
Bus Type SATA I, SATA II, SATA II
Supported Drive Form Factor 9.5 mm, 2.5” SATA/DRIVES
Connector Types
2 x 15-pin SATA Power Female (external)
2 x 15-pin SATA Power Female (internal)
2 x SATA 7-pin Data Female (external)
2 x SATA 7-pin Data Female (external)
2 x 4-pin LED
Weight 270 g (9.53 oz )
Dimensions
(W x H x L)
101 mm (3.98” ) x 25 mm (0.98”) x 123 mm
(4.84” )
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.