StarTech.com MOD4AVHD User Manual
Displayed below is the user manual for MOD4AVHD by StarTech.com which is a product in the AV Conferencing Bridges category. This manual has pages.
Related Manuals
Quick-Start Guide
Manual Revision: 11/09/2018
Product Diagram
Actual product may vary from photos.
Front View
Rear View
Package Contents
• A/V Module x 1
• Universal Power Adapter x 1
• Power Clips (NA, EU, UK) x 3
• Mounting Bracket x 1
• Mounting Bracket Screws (M5 x 20 mm) x 4
• Module Screws (#6-32 x 3/16”) x 8
• Quick-Start Guide x 1
SKU #: MOD4AVHD
A/V Connectivity Module for BOX4MODULE and BEZ4MOD
Requirements
• Power Source (i.e. AC Electrical Outlet)
Installation Requirements:
• Mounting Surface
• Mounting Bracket x 1
• Mounting Bracket Screws (M5 x 20 mm) x 4
• Module Screws (#6-32 x 3/16”) x 4
• Writing Utensil x 1
• Phillips Head Screwdriver x 1
For the latest requirements, please visit:
www.startech.com/MOD4AVHD.
Installation
See the Installation section in the Modular Conference Table
Box (BOX4MODULE) or Single-Module Conference Table Box
(BEZ4MOD) User Manual for instructions on how to install a
Module.
These User Manuals can be found under the Support tab at:
www.startech.com/BOX4MODULE
www.startech.com/BEZ4MOD
(Optional) Mounting the Module
Note: StarTech.com is not responsible for any damages related to
the installation of this product.
Note: Before mounting the Module, consider the desired
orientation of the ports (front and rear).
1. Align the Mounting Bracket with four Mounting Holes on the
Module.
Note: There are four Mounting Holes on each side of the
Module, which gives you two dierent mounting options.
2. Insert the Module Screws (x4) through the Mounting Bracket
and into the Mounting Holes.
3. Tighten the Module Screws using a Phillips Head Screwdriver.
Do not overtighten the Module Screws.
4. Before installing the Mounting Bracket on or under your
Mounting Surface, measure and position the Mounting
Bracket in the desired location. The Module can be mounted on
a vertical or horizontal Mounting Surface.
5. (Optional) Depending on the Mounting Surface you are using
to install the product, you may need to drill pilot holes prior to
installing the Mounting Bracket Screws into the Mounting
Surface.
6. Mark the location of the Mounting Holes using a Writing
Utensil. These marks can be used as a guide to indicate where
the Mounting Bracket Screws will be installed in the surface.
7. Install the Mounting Bracket Screws (x4) through the Mounting
Bracket and into the Mounting Surface, using a Phillips Head
Screwdriver. Do not overtighten the Mounting Bracket Screws.
Warning: To prevent the Mounting Bracket Screws from
penetrating the opposite side of the Mounting Surface, be
conscious of the length of the Mounting Bracket Screws
compared to the depth of the Mounting Surface.
For the latest information, specications, and support visit www.startech.com/MOD4AVHD
Power
LED
Reset
Button
RJ45
Passthrough
Port
VGA In
Port
Audio
In Port HDMI
In Port
DisplayPort
In Port
RJ45
Passthrough
Port
HDMI
Out
Port
Audio
Out
Port
DC
5V 2A
Port
VGA In
Port
Audio
In Port
HDMI
In Port
DisplayPort
In Port
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
• Wiring terminations should not be made with the product and/or electric lines under power.
• Product installation and/or mounting should be completed by a certied professional as per
the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed to avoid creating
electric, tripping or safety hazards.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous
tension.
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit et/ou les câbles
électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un professionnel certié et
dans le respect des normes locales et du code de construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent être placés et
acheminés de façon à éviter tout risque électrique, de chute ou de sécurité
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
• 電源が入っている状態の製品または電線の終端処理を行わないでください。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよ
うにしてください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le linee elettriche
sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un tecnico
professionale certicato che conosca le linee guida locali sulle norme edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati e stesi in modo da
evitare pericoli di inciampo, rischi di scosse elettriche o pericoli per la sicurezza.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
• Montering av kabelavslutningar får inte göras när produkten och/eller elledningarna är
strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner och enligt
gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så sätt att risk för
snubblingsolyckor och andra olyckor kan undvikas.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or
modications not expressly approved by StarTech.com could void the user’s authority to operate
the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company in question. StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of their
respective holders.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit www.startech.com/
support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two-year warranty. StarTech.com warrants its products against defects
in materials and workmanship for the periods noted, following the initial date of purchase. During
this period, the products may be returned for repair, or replacement with equivalent products at
our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its
products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers,
directors, employees or agents) for any damages (whether direct or indirect, special, punitive,
incidental, consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss,
arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If
such laws apply, the limitations or exclusions contained in this statement may not apply to you.
To view manuals, FAQs, videos, drivers, downloads, technical drawing, and more, visit www.startech.com/support.
Quick-Start Guide
Startech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd., Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
IT: it.startech.com
JP: jp.startech.com
NL: nl.startech.com
SKU #: MOD4AVHD
Powering the Module
1. On the bottom of the A/V Connectivity Module, connect the
Universal Power Adapter to the DC 5V 2A Port.
2. Tighten the Lock Screw on the Universal Power Adapter’s
Barrel Connector, to ensure connectivity.
3. Connect the other end of the Universal Power Adapter to an
appropriate Power Source.
Connecting a Device to the Module
For instructions on how to connect devices to the Module see
the Connecting Devices to the Top of the Module and Connecting
Devices to the Bottom of the Module sections in the User Manual.
The User Manual can be found under the Support tab at:
www.startech.com/MOD4AVHD.
LED Indicator
Power
Solid LED (White)
• Indicates that the A/V Connectivity Module is active (the
Universal Power Adapter is correctly connected to an AC
Electrical Outlet).
LED O
• Indicates that the Universal Power Adapter is not correctly
connected to an AC Electrical Outlet or the A/V Module is not
receiving power from the AC Electrical Outlet.