StarTech.com MOD4AVHDBT User Manual
Displayed below is the user manual for MOD4AVHDBT by StarTech.com which is a product in the AV Conferencing Bridges category. This manual has pages.
Related Manuals
i
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.
ii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
iii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ
い。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に
従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
iv
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
Warning Statements
Make sure to assemble this product according to the instructions. Failure to do
so might result in personal injury or property damage.
Never use this product if parts are missing or damaged.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements ........................................................................i
Safety Statements ..................................................................................iii
Warning Statements ..............................................................................iv
Product Diagram ....................................................................................1
Top View ....................................................................................................................................................... 1
Bottom View ................................................................................................................................................2
Side View ...................................................................................................................................................... 3
Product Information ..............................................................................4
Package Contents .....................................................................................................................................4
Requirements ............................................................................................................................................. 4
Installation ..............................................................................................5
Mounting ..................................................................................................................................................... 5
Powering the Module .............................................................................................................................. 6
Connecting Devices to the Bottom of the Module ...........................7
RJ45 Passthrough Port ............................................................................................................................ 7
CAT5e/6 Video Port ................................................................................................................................... 7
HDMI Out Port ............................................................................................................................................ 8
Audio Out Port ........................................................................................................................................... 8
DC 5V 2A Port ............................................................................................................................................. 8
DisplayPort In Ports .................................................................................................................................. 8
HDMI In Port ................................................................................................................................................ 9
Audio In Port ............................................................................................................................................... 9
VGA In Port .................................................................................................................................................. 9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Connecting Devices to the Top of the Module ..................................10
RJ45 Passthrough Port ............................................................................................................................ 10
VGA In Port .................................................................................................................................................. 10
Audio In Port ............................................................................................................................................... 10
HDMI In Port ................................................................................................................................................ 11
DisplayPort In Port .................................................................................................................................... 11
Operation ................................................................................................11
LED Indicators............................................................................................................................................. 11
Reset Button ................................................................................................................................................ 12
Automatic Video Switching .................................................................................................................. 12
Dual Display Output ................................................................................................................................. 12
Conguration ..........................................................................................13
Conguring a Display .............................................................................................................................. 13
Display Preferences .................................................................................................................................. 14
Maximum Resolution Chart ..................................................................15
Connectivity Diagram ...........................................................................16
1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Actual product may vary from photos.
Top View
Power
LED
Reset
Button
DisplayPort
In Port
HDMI
In Port
Audio
In Port
VGA In
Port
RJ45
Passthrough
Port
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Bottom View
RJ45
Passthrough
Port
CAT5e/6
Video
Port
HDMI
Out
Port
Audio
Out
Port
DC
5V 2A
Port
DisplayPort
In Port
HDMI
In Port
Audio
In Port
VGA In
Port
3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Side View
Mounting Holes
Mounting
Holes
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
• A/V Module x 1
• Universal Power Adapter x 1
• Power Clips (NA, EU, UK) x 3
• Mounting Bracket x 1
• Mounting Bracket Screws (M5x20 mm) x 4
• Module Screws( #6-32 x 3/16’’) x 8
• Quick-Start Guide x 1
Requirements
For the latest requirements, please visit
www.startech.com/MOD4AVHDBT.
Installation:
• Mounting Bracket x 1
• Mounting Bracket Screws (M5x20 mm) x 4
• Module Screws (#6-32 x 3/16”) x 4
• Writing Utensil x 1
• Phillips Head Screwdriver x 1
Laptop:
• HDMI, DisplayPort, or VGA Video Output Devices
Display:
• HDMI Enabled Display Device (up to 4K@30Hz) x 1
• HDMI Cable x 1
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Devices:
• Network Device x 1
• CAT5e/6 Cables x 3
• Audio Input Devices x 2
• Audio Output Device x 1
Power
• Power Source (e.g. Wall Outlet, Power Bar, etc.) x 1
Installation
Warning: Test the functionality of MOD4AVHDBT with your
equipment to ensure compatibility before installation.
Note: StarTech.com is not responsible for any damages
related to the installation of this product.
See the Installation section in the Modular Table Box
(BOX4MODULE) or Single-Module Table Box (BEZ4MOD)
User Manual for instructions on how to install a Module
(found at www.startech.com/BEZ4MOD or www.startech.com/
BOX4MODULE - Table Boxes are sold separately).
Mounting
Using the Included Mounting Bracket
Note: Before mounting the Module, consider the desired
orientation of the Ports (front and rear).
1. Align the Mounting Bracket with four Mounting Holes on
the Module.
Note: There are four Mounting Holes on each side of the
Module, which allows you to mount the Module in one of
two dierent positions.
6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Insert the Module Screws (x4) through the Mounting
Bracket and into the Mounting Holes.
3. Tighten the Module Screws using a Phillips Head
Screwdriver. Do not over-tighten the Module Screws.
4. Before installing the Mounting Bracket on or under the
Mounting Surface, measure and position the Mounting
Bracket in the desired location. The Module can be
mounted on a vertical or horizontal Mounting Surface.
5. (Optional) Depending on the Mounting Surface you are
using to install the product, you may need to drill pilot holes
prior to installing the Mounting Bracket Screws into the
Mounting Surface.
6. Mark the location of the Mounting Holes using a Writing
Utensil. These marks can be used as a guide to indicate
where the Mounting Bracket Screws will be installed in the
surface.
7. Install the Mounting Bracket Screws (x4) through the
Mounting Bracket and into the Mounting Surface, using
a Phillips Head Screwdriver. Do not over-tighten the
Mounting Bracket Screws.
Warning: To prevent the Mounting Bracket Screws from
penetrating the opposite side of the Mounting Surface, be
conscious of the length of the Mounting Bracket Screws
compared to the depth of the Mounting Surface.
Powering the Module
1. On the bottom of the A/V Module, connect the Universal
Power Adapter to the DC 5V 2A Port.
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Tighten the Lock Screw on the Universal Power Adapter’s
Barrel Connector, to prevent the cable from accidentally
disconnecting from the A/V Module.
3. Connect the other end of the Universal Power Adapter to
an appropriate Power Source.
Connecting Devices to the Bottom of the
Module
Tip: Devices being used in your boardroom can be
connected to the bottom of MOD4AVHDBT, to reduce
table top cable clutter.
RJ45 Passthrough Port
The RJ45 Passthrough Port is used to connect a Network
Device to the A/V Module.
1. Connect a CAT5e/6 Cable’s RJ45 Connector to the RJ45
Passthrough Port on the A/V Module.
2. Connect the other RJ45 Connector on the CAT5e/6 Cable
to an RJ45 Port on a Network Device.
CAT5e/6 Video Port
Extend Video and Audio
(STHDBTRX Receiver is Sold Separately)
The CAT5e/6 Video Port is used to connect a Video Display
Device to the A/V Module. The CAT5e/6 Video Port can also
be used to connect an HDMI Over CAT5e/6 Receiver.
1. Connect a CAT5e/6 Cable’s RJ45 Connector to the CAT5e/6
Video Port on the A/V Module.
8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Connect the other RJ45 Connector on the CAT5e/6 Cable
to an RJ45 Port on a Video Source Device or an HDMI Over
CAT5e/6 Receiver.
HDMI Out Port
The HDMI Out Port is used to connect an HDMI Enabled
Display Device to the A/V Module.
1. Connect an HDMI Cable to the HDMI Out Port on the AV
Module.
2. Connect the other end of the HDMI Cable to an HDMI Port
on your HDMI Enabled Display Device.
Audio Out Port
The Audio Out Port is used to connect an Audio Device (e.g.
Headphones, Speakers, etc.) to the A/V Module.
1. Connect a 3.5 mm Audio Cable to the Audio Out Port on
the A/V Module.
2. If connecting speakers, connect the other end of the 3.5 mm
Audio Cable to the Audio In Port on the Audio Device.
DC 5V 2A Port
See Powering the Module.
DisplayPort In Ports
The DisplayPort Ports enable you to connect DisplayPort
Video Source Devices to the A/V Module for use with the
connected Host Computer.
9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
1. Connect a DisplayPort Cable to the DisplayPort Port on
the A/V Module.
2. Connect the other end of the DisplayPort Cable to a
DisplayPort port on the DisplayPort Video Source Devices.
HDMI In Port
The HDMI In Port is used to connect a Video Source Device to
the A/V Module.
1. Connect an HDMI Cable to the HDMI In Port on the A/V
Module.
2. Connect the other end of the HDMI Cable to an HDMI port
on a Source Device.
Audio In Port
The Audio In Port is used to connect an Audio Source Device
to the A/V Module.
1. Connect a 3.5 mm Audio Cable to the Audio In Port on the
A/V Module.
2. Connect the other end of the 3.5 mm Audio Cable to the
Audio Out Port on the Audio Source Device.
VGA In Port
The VGA In Port is used to connect a Video Source Device to
the A/V Module.
1. Connect a VGA Cable to the VGA In Port on the A/V
Module.
2. Connect the other end of the VGA Cable to a VGA Output
Port on the Video Source Device.
10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Connecting Devices to the
Top of the Module
RJ45 Passthrough Port
The RJ45 Passthrough Port is used to connect a Network
Device to the A/V Module.
1. Connect a CAT5e/6 Cable’s RJ45 Connector to the RJ45
Passthrough Port on the A/V Module.
2. Connect the other RJ45 Connector on the CAT5e/6 Cable
to an RJ45 Port on a Network Device.
VGA In Port
The VGA In Port is used to connect a Video Source Device to
the A/V Module.
1. Connect a VGA Cable to the VGA In Port on the A/V
Module.
2. Connect the other end of the VGA Cable to a VGA Output
Port on the Video Source Device.
Audio In Port
The Audio In Port is used to connect an Audio Source Device
to the A/V Module.
1. Connect a 3.5 mm Audio Cable to the Audio In Port on the
A/V Module.
2. Connect the other end of the 3.5 mm Audio Cable to the
Audio Out Port on the Audio Source Device.
11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
HDMI In Port
The HDMI In Port is used to connect a Source Device to the
A/V Module.
1. Connect an HDMI Cable to the HDMI In Port on the A/V
Module.
2. Connect the other end of the HDMI Cable to an HDMI port
on a Source Device.
DisplayPort In Port
The DisplayPort Port enables you to connect a Display Device
to the A/V Module for use with the connected Host Computer.
1. Connect a DisplayPort Cable to the DisplayPort Port on
the A/V Module.
2. Connect the other end of the DisplayPort Cable to a
DisplayPort port on the Video Source Device.
Operation
LED Indicators
Power
Solid LED (White)
• Indicates that the A/V Module is active (the Universal Power
Adapter is correctly connected to an AC Electrical Outlet).
LED O
• Indicates that the Universal Power Adapter is not correctly
connected to an AC Electrical Outlet or the A/V Module is
not receiving power from the AC Electrical Outlet.
12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Reset Button
Press and release the Reset Button in to reset the EDID settings.
Automatic Video Switching
Automatic video switching allows you to connect an HDMI, DP
or VGA Video Source to an HDMI Display or Projector without
the hassle of menu and input selections by automatically
switching to the most recently connected or powered-on
Source.
Dual Display Output
The CAT5e/6 Video Port and HDMI Out Port can be used to
simultaneously output A/V content to two dierent Displays.
13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Conguration
Conguring a Display
Video output capabilities are dependent on the video card and
hardware specications of the connected Host Computer and
Displays.
Note: Navigating to the Settings screen will vary depending
on the operating system (OS) or operating system version
running on the host laptop.
Windows:
1. Right-click on the Desktop and select Screen Resolution or
Display Settings (depending on the OS version) from the
pop-up menu.
2. Adjust the Display Order, Screen Resolution, Orientation
and Display Mode as needed.
macOS:
1. Click the Apple Icon and select System Preferences.
2. Click Displays to open the Display Preferences screen.
3. On the Display Preferences screen, you can congure your
system’s display settings.
14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Display Preferences
Orientation:
• Landscape: Sets the Display in a horizontal orientation.
• Portrait: Sets the Display in a vertical orientation.
Multiple Displays:
• Extend desktop to this display: Extends your desktop area
across multiple Displays, enabling you to move applications
from one Display to the other.
• Duplicate desktop on: Duplicates the desktop marked as
the main Display onto the selected Display.
• Disconnect this display: Disconnects the selected Display.
Make this my main display:
• Select this check box to mark the current Display as the main
or primary Display. When using the other Display types, the
main Display will either be extended (Extend desktop to this
display) or Duplicated (Duplicate this display).
Resolution:
• The number of pixels rendered on the Display measure as
width x height (e.g. 1920 x 1080).
15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Maximum Resolution Chart
Input Port HDMI Output
Resolution
CAT5e/6 Video Output
Resolution
Top HDMI In
Port
Up to 3840
x 2160 30Hz
+ 7.1/5.1/2
channel audio
Up to 3840 x 2160 30Hz with
35 m extension / 1920 X 1080
60Hz with 70 m extension +
7.1/5.1/2 channel audio
Top
DisplayPort
In Port
Up to 3840
x 2160 30Hz
+ 7.1/5.1/2
channel audio
Up to 3840 x 2160 30Hz with
35 m extension / 1920 X 1080
60Hz with 70 m extension +
7.1/5.1/2 channel audio
Top VGA In
and Audio In
Ports
1920 X 1080
60Hz + 2
channel audio
1920 X 1080 60Hz with 70 m
extension + 2 channel audio
Bottom
HDMI In Port
Up to 3840
x 2160 30Hz
+ 7.1/5.1/2
channel audio
Up to 3840 x 2160 30Hz with
35 m extension / 1920 X 1080
60Hz with 70 m extension +
7.1/5.1/2 channel audio
Bottom
DisplayPort
In Port
Up to 3840
x 2160 30Hz
+ 7.1/5.1/2
channel audio
Up to 3840 x 2160 30Hz with
35 m extension / 1920 X 1080
60Hz with 70 m extension +
7.1/5.1/2 channel audio
Bottom VGA
In and Audio
In Ports
1920 X 1080
60Hz + 2
channel audio
1920 X 1080 60Hz with 70 m
extension + 2 channel audio
16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Connectivity Diagram
17
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or
their ocers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of
prots, loss of business, or any pecuniary loss, arising out of or related to the use
of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
17
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle
15 Gowerton Rd.,
Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support