StarTech.com PEX16S550LP User Manual
Displayed below is the user manual for PEX16S550LP by StarTech.com which is a product in the Interface Cards/Adapters category. This manual has pages.
Related Manuals
Manual Revision: 11/03/2017
For the latest information, technical specications, and support for
this product, please visit www.StarTech.com/PEX16S550LP.
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
PEX16S550LP
16-Port Serial Card
*actual product may vary from photos
Instruction manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Instruction manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction manual
i
Table of Contents
Product diagram ....................................................................................1
Top view ....................................................................................................................................................... 1
Front view .................................................................................................................................................... 1
DB9 RS232 connector pinout - male .................................................................................................. 2
Introduction ............................................................................................ 2
Packaging contents .................................................................................................................................. 3
Requirements ............................................................................................................................................. 3
About the jumpers .................................................................................4
JP1 – Power selector ..............................................................................4
JP3 and JP2 - Serial port power ...........................................................5
JP4 – UART power selector .................................................................................................................... 5
JP5 - Mode setting .................................................................................................................................... 5
JP6 - PME setting ....................................................................................................................................... 5
Hardware installation ............................................................................6
Install the low-prole bracket ............................................................................................................... 6
Install the PCIe Card ................................................................................................................................. 6
Software installation .............................................................................7
Install the driver – Windows .................................................................................................................. 7
Technical support ...................................................................................8
Warranty information ............................................................................ 8
Instruction manual
1
Product diagram
Top view
Front view
Bracket (full-prole pictured)
PCI Express x1 connector
JP4-VART
power JP6-PME
JP1-AUX power
source
SATA power
connector
JP5: Mode
JP2: PWR 9-16
JP3: PWR 1-8
Screw locks Screw locks
VHDC1-68 port 2
VHDC1-68 port 1
Instruction manual
2
DB9 RS232 connector pinout - male
or power
Introduction
This serial card lets you add 16 RS232 serial ports to your full or small form-factor
computer through a PCI Express expansion slot. It’s a convenient solution for
connecting modern or legacy serial devices to your computer, with support for
data transfer rates up to 921.6Kbps. It includes two 8-port breakout cables so you
can connect up to 16 serial devices to this single card, even in low-prole computer
systems.
Instruction manual
3
Packaging contents
• 1 x serial card
• 1 x low-prole bracket
• 2 x breakout cables
• 1 x driver CD
• 1 x quick-start guide
Requirements
• A host computer with a PCI Express x1 slot
• A CD-ROM, DVD-ROM, or other compatible optical drive (for driver CD installation)
• RS232 serial cables (DB9)
• Any of the following operating systems:
• Windows® 10
• Windows 8.1
• Windows 8
• Windows 7
• Windows Server® 2012
• Linux® 2.4.x and later (tested up to 4.04)
Requirements are subject to change. For the latest requirements, please visit www.
StarTech.com/PEX16S550LP.
Instruction manual
4
About the jumpers
JP1 – Power selector
This jumper is used to provide pin number nine of the serial port connector(s) with
DC5V or DC12V power. There are four sources depending on the jumper’s position.
JP1: Power selector Setting
Internal 5V: Power source is +5VDC, from
the motherboard’s PCI Express slot
Internal 12V: Power source is +12VDC, from
the motherboard’s PCI Express slot
Internal 12V: Power source is +12VDC, from
the motherboard’s PCI Express slot
Internal 5V: Power source is +5VDC, from
the motherboard’s PCI Express slot
15V
I12V
X12V
X5
15V
I12V
X12V
X5
15V
I12V
X12V
X5
15V
I12V
X12V
X5
Instruction Manual
5
JP3 and JP2 - Serial port power
These two jumpers are used to provide external power to the two breakout cables or
the 16 serial ports. JP3 enables or disables power over ports 1 to 8, and JP2 enables or
disables power over ports 9 to 16. When enabled, the card connects DC power to pin 9
of the DB9 port(s).
JP1: Power selector Setting
No power is supplied to pin nine on the serial
ports
Power is supplied to pin nine on the serial ports
and the power source is determined by what is
selected at JP1
DIS ENA
DIS ENA
JP4 – UART power selector
Leave at the default setting (3.3V).
JP5 - Mode setting
This is for factory test purposes only. The jumper must be xed at SB.
JP6 - PME setting
This jumper enables or disables wake from sleep.
JP1: Power selector Setting
PME is disabled
PME is enabled
ENA DIS
ENA DIS
(default)
Instruction Manual
6
Hardware installation
Install the low-prole bracket
The serial card can be installed in a low-prole (half-height) or a full-prole computer.
The full-prole bracket comes preinstalled on the card, but if you have a small form-
factor computer, you can install the low-prole bracket instead.
1. Remove the four screw locks that are securing the two VHDCI-68 ports to the full-
prole bracket.
2. Remove the full-prole bracket from the card.
3. Align the low-prole bracket’s VHDCI-68 port hole with the card’s VHDCI-68 ports.
4. Insert the VHDCI-68 ports into the VHDCI-68 port hole on the low-prole bracket
using the four screw locks from step 1.
5. Insert the four screw locks from step 1 and tighten them into place on the low-
prole bracket.
Install the PCIe Card
Warning! PCIe cards can be severely damaged by static electricity. If an anti-static strap
isn’t available, discharge any built-up static electricity by touching a large grounded
metal surface for several seconds.
1. Turn o your computer and any devices or peripherals that are connected to it, such
as printers or external storage devices.
2. Unplug the power cable from the back of your computer.
3. Disconnect any peripheral devices that are connected to your computer.
4. Remove the cover from your computer case. Consult the documentation that came
with your computer for details about how to do this safely.
5. Locate an open PCIe slot and remove the corresponding metal cover plate from
the back of your computer case. Consult the documentation that came with your
computer for details about how to do this safely. This card works in PCIe slots of x1,
x4, x8, or x16 lanes.
6. Gently insert the card into the open PCIe slot and fasten the bracket to the back of
the case.
Note: If you install the card into a low-prole (small form-factor) desktop system, it
might be necessary to replace the preinstalled full-prole bracket with the included
low-prole bracket. See “Install the low-prole bracket” for instructions on how to do
this.
Instruction Manual
7
7. (Optional) Connect a SATA power cable from your computer’s power supply to the
card’s SATA power connector.
8. Place the cover back onto your computer case.
9. Reconnect the power cable to the back of your computer.
10. Reconnect all of the peripheral devices that you disconnected in step 3.
11. Turn on your computer.
Software installation
Install the driver – Windows
1. Insert the provided driver CD into your computer’s CD-ROM or DVD-ROM drive.
2. Navigate to and open Device Manager.
3. Under Other devices, right-click on the PCI Serial Port device then click Update
Driver Software.
4. Click the Browse my computer for driver software button.
5. Click the Browse button.
6. Navigate to your CD-ROM or DVD-ROM location.
7. Navigate through the following folder directories: IO\SYSTEMBASE\DRIVERS\
PCI(PCIe Bridge).
8. Select the Windows folder that’s applicable to the operating system running on
the computer. For 32-bit versions of Windows select the 32bit_Win10_8.x_7_
Vista_XP_2008_2003_2000 folder. For 64-bit versions of Windows select the 64bit_
Win10_8.x_7_Vista_XP_2008_2003_2000 folder, then click the OK button.
9. Click the Next button to complete the installation process.
Instruction manual
8
Technical support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty information
This product is backed by a two-year warranty.
StarTech.com warrants its products against defects in materials and workmanship
for the periods noted, following the initial date of purchase. During this period,
the products may be returned for repair, or replacement with equivalent
products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.