StarTech.com PM1115UW User Manual
Displayed below is the user manual for PM1115UW by StarTech.com which is a product in the Print Servers category. This manual has pages.
Related Manuals
Manual Revision: 04/24/2017
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
Wireless N USB 2.0 Network Print Server
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Instruction Manual
3
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC dénies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une
distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.
L’émetteur ne doit ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à
leur proximité.
FCC ID: 2AA3I-PM1115UWB
IC: 11232A-PM1115UWB
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ............................................................................................ 1
Packaging Contents ................................................................................................................................. 1
System Requirements ..............................................................................................................................1
Product Diagram ....................................................................................2
Front View .................................................................................................................................................... 2
Rear View ...................................................................................................................................................... 2
LED Indicators............................................................................................................................................. 3
Reset Button ................................................................................................................................................ 3
Installation ..............................................................................................4
Hardware Installation ..............................................................................................................................4
Software Installation ................................................................................................................................ 4
Technical Support ..................................................................................7
Warranty Information ............................................................................ 7
Instruction Manual
1
Introduction
Packaging Contents
• 1x Wireless USB Print Server
• 1x Power Adapter
• 1x Software CD
• 1x Quick Start Guide
System Requirements
• Windows® 10, 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP (32/64), Windows Server®
2012, 2008 R2, 2003 (32/64), Mac OS 10.x, 9.x, Linux 2.4.x / 2.6.x / 3.x (tested up
to 3.5)
Instruction Manual
2
Product Diagram
Front View
Rear View
WLAN LED
WPS Button
Reset Button
DC Jack
LED Indicators
USB Port
Ethernet Port
Instruction Manual
3
LED Indicators
LED State Indication
Status Blinking for POST (Yellow)
When power is connected, the Status
indicator will ash ve times, and then
go solid.
USB On (Green) LAN Port has a valid network connection
at 100Mbps.
WLAN On (Yellow) LAN Port has a valid network connection
at 10Mbps.
Reset Button
Reboot the Print Server:
1. Verify the power of print server is turned on.
2. Press the reset button once, and then release it.
Note: This will restart the print server and stop all on-going and pending print jobs.
Print a Self-test Page
1. With the print server powered on and your printer connected and powered, press
the reset button for 8 seconds, and then release it.
2. A test page including the current print server settings will be printed.
Reset to Factory Defaults:
1. Disconnect the power adapter from the print server.
2. Hold down the reset button.
3. Reconnect the power adapter while continuing to hold the reset button for about 5
seconds.
4. Release the reset button.
5. The print server will restart.
WARNING: This will erase all settings on the print server and return it to factory
default.
Instruction Manual
4
Default Settings
Username: admin
Password: (None)
Wireless Mode: Ad-Hoc (Peer-to-Peer)
SSID: PM1115UW
IP Address: 192.168.0.10
Installation
Hardware Installation
1. Turn o the power to your printer.
2. Connect the print server to your printer with the appropriate printer cable.
3. Turn the printer on.
4. Plug in the AC power adapter into the DC jack on the print server.
5. Wait ~40 seconds for the print server’s Power On Self Test (POST) to complete.
6. (Optional) Connect an RJ45 network cable to the print server, then to your network
switch or wall jack.
Software Installation
For full operating instructions and specications, please visit www.startech.com/
PM1115UW
Windows
1. Find the wireless print server by viewing your available wireless networks and
connecting to the PM1115UW SSID.
Note: If you cannot nd the PM1115UW network, then your version of Windows may
not be congured to show Ad-Hoc wireless networks. To resolve this issue, you need
to use an RJ45 cable to either connect your print server to your network switch or to
connect directly to the computer. When the setup is complete, you can disconnect the
network cable.
2. Insert the setup CD into your CD/DVD drive.
3. Select “Run autorun.exe” from the Autoplay menu. If Autoplay is disabled on your
system, browse to your CD/DVD drive and run the application.
Note: The setup CD will install the print server driver, PSAdmin and Setup Wizard
into your computer. The default installation directory will be C:\Program les\
Network Print Monitor.
Instruction Manual
5
4. Click Next on the following screen and the wizard will automatically discover the
print server. At this point of the install, you may Windows Firewall message, click
Allow Access if prompted.
5. From the “Select A Print Sever” screen, select the print server that you want to
congure and click Next.
6. Click “Yes, I want to change settings”, then click Next to congure the wireless and IP
settings of the print server to match your network:
Select your desired Communication Type:
• Infrastructure (Access Point)
• Ad-Hoc (Peer-to-Peer; default)
SSID:
• If using Ad-Hoc mode, enter the SSID you would like the print server to display
• If using Infrastructure mode, enter the SSID of the access point that you want to
connect to
Note: If you require a site survey to determine the names of available access points,
please use the web console method, outlined in the full online manual.
• Channel: optional
• Data Transmit Rates: select Auto or others
• Transmit Mode: select Auto or others
• On the Wireless Security screen, enable or disable WEP/WPA/WPA2 encryption,
congure according to your wireless network and click Next.
• On the TCP/IP Settings screen, specify a xed or dynamic IP address for the print
server, a xed IP address is highly recommended. Click Next.
Note: The IP address of print server must be within the same subnet as your network
adapter.
7. In the setup wizard, select an already congured printer from the list, click Next,
Next and then Finish to complete the installation.
OR
Select Add New Printer to launch the Windows Add Printer Wizard, if the print server is
connected to a printer that hasn’t been installed before and does not appear in the list.
8. Click Next and select Local Printer, make sure the “Automatically detect and install
my Plug and Play printer” check box is NOT checked. Then click Next.
Instruction Manual
6
9. Make sure the Use the following port radio-button is clicked and select LPT1:
(recommended Printer Port) from the pull-down list. Then click Next.
10. Select Manufacturer and Printer from the lists of printer drivers. Then
click Next.
11. If you already have the printer’s driver installed, you will be asked whether
to keep it or to replace it. Click Next. Supply a name for the printer and choose
whether you want to make it your default printer. Then click Next.
12. Then, choose whether you want to share the printer with other network user,
print a test page (please select No.), etc. Select the appropriate radio-button and
click Next and Finish.
13. In the setup wizard, nish the installation by highlighting the installed printer in
the Select a Printer list and click Next, Next -> Finish.
14. Click Start -> Printers and Faxes and highlight your newly installed printer.
15. Right-click, select Properties, then the Ports tab and verify that the print server’s
port appears.
16. Select the General tab and click Print Test Page to verify the conguration.
Note: If you want to install more print servers, start the setup wizard from your
Windows Start menu: Start -> All Programs -> Network Print Server -> PSWizard
and repeat the installation procedure.
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.