StarTech.com POEEXT1G60W User Manual
Displayed below is the user manual for POEEXT1G60W by StarTech.com which is a product in the Network Extenders category. This manual has pages.
Related Manuals
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: June 19, 2020
Product Diagram (POEEXT1G60W)
Front View
Side View
Component Function
1PoE Output LED
Indicator
• Indicates the current status of the PoE Powered
Device (PD)
• ON - Power Source Equipment (PSE) is activated and
PD is detected
• OFF - PSE is not detecting PD
2PoE Input LED
Indicator
• Indicates the current status of the PSE
• ON - Power is detected
• O - Power is not detected
3PoE Input Port • PSE provides power and data to the PoE Extender
through a Network Cable
60W Industrial-Grade Hardened 802.3af/at PoE Extender 10/100/1000 Mbps
4PoE Output Port • The power and data is forwarded to the PD through a
Network Cable
5PoE Input and Output
LED Indicators
• Indicates the connection status and network speeds of
the PoE Input Port and the PoE Output Port
6Grounding Screw • Attach a Grounding Wire to protect Network
Equipment
Requirements
For the latest requirements, please visit www.startech.com/POEEXT1G60W.
• Power Source Equipment x 1
• Powered Device x 1
• RJ45 Terminated UTP/STP Cat 5e (or better) Network Cable (sold separately) x 2
• Earth Ground Connection x 1
• Ground Wire x 1
• (Optional) #2 Phillips Head Screwdriver x 1
• (Optional) Screws for Wall Mounting x 2
Installation
Grounding the PoE Extender
1. Using the Phillips Head Screwdriver loosen the Grounding Screw on the PoE
Extender.
2. Attach the Grounding Wire to the Grounding Screw.
3. Tighten the Grounding Screw.
4. Connect the other end of the Grounding Wire to the Earth Ground Connection.
Connecting the PoE Extender to an Existing PoE Connection
1. Connect a Network Cable to the Output Port on a PSE Device and to the PoE
Input Port on the PoE Extender.
2. Connect a Network Cable to the PoE Output Port on the PoE Extender and to the
Input Port on the PD.
Cascade PoE Extenders
1. Connect a Network Cable to the Output Port on a PSE Device and to the PoE
Input Port on the PoE Extender.
2. Connect a Network Cable to the PoE Output Port on the PoE Extender and to the
PoE Input Port on the next PoE Extender.
6
1
3 4
2
5
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or
agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots,
loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Operation
PoE Input and Output LED Indicators
LED Type/
Color Status Indication
LNK/Green On • Connection established
O • No connection established
Flashing • Data transmission detected
SPD/Amber On • 1000 Mbps link speed detected
O • 100 Mbps link speed detected
3. Repeat step 3 until a total of 4 PoE Extenders are connected.
4. Connect a Network Cable to the PoE Output Port on the last PoE Extender and to
the Input Port on the PD.
(Optional) Mounting the PoE Extender
Wall Mounting
1. Align the holes in the Wall Mount Brackets with the holes in the back of the PoE
Extender.
2. Insert two Phillips Head Screws through each Wall Mount Bracket and into the PoE
Extender.
3. Tighten the Phillips Head Screws using a Phillips Head Screwdriver (sold
separately).
Note: Be careful not to over-tighten the Screws.
4. Insert two Screws (sold separately) through the Wall Mount Brackets and into the
Mounting Surface.
5. Tighten the Screws using the appropriate Screwdriver.
DIN Rail Mounting
1. Align the holes in the DIN Rail Bracket with the holes in the back of the PoE
Extender.
2. Insert three Phillips Head Screws through the DIN Rail Bracket and into the PoE
Extender.
3. Tighten the Phillips Head Screws using a Phillips Head Screwdriver.
Note: Be careful not to over-tighten the Screws.
4. Hang the top of the DIN Rail Bracket (the section with the two metal clips) onto a
Top Hat style DIN Rail.
5. Press the DIN Rail Bracket down and forward to lock the bottom section onto the
DIN Rail.