StarTech.com PROJWALLMNT User Manual
Displayed below is the user manual for PROJWALLMNT by StarTech.com which is a product in the Projector Mounts category. This manual has pages.
Related Manuals
i
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United
States or other countries.
ii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
Mesures de sécurité
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
安全対策
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に
従い、有資格の専門業者が行うようにしてください。
Misure di sicurezza
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
Säkerhetsåtgärder
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
iii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Warning Statements
• Make sure to assemble this product according to the instructions. Failure to
do so might result in personal injury or property damage.
• Never use this product if parts are missing or damaged.
• The projector wall mount is designed to be installed on a wood stud, solid
concrete, or cinder block wall. The wall structure should also be capable of
supporting at least four times the weight of the mounted equipment.
• The mounting hardware included with this product may not be adequate for
installation on certain wall structures. Failure to comply with these warnings
may result in personal injury or damage to the equipment.
• If you lack the necessary expertise to attach this product to the wall structure
that you’re using, contact a construction professional to install the wall
mount or to provide specic mounting instructions for your wall structure.
Mensagens de Aviso
• Certique-se de que monta este produto de acordo com as instruções.
O incumprimento pode resultar em ferimentos pessoais ou danos de
propriedade.
• Nunca opere este produto se faltarem peças ou estas estiverem danicadas.
• As estruturas de parede variam e é importante certicar-se de que o tipo de
estrutura de parede e hardware de montagem que está a usar irá suportar
devidamente o equipamento montado. O incumprimento pode resultar
em ferimentos pessoais e/ou danos no equipamento. A estrutura de parede
deve ser capaz de suportar pelo menos quatro vezes o peso do equipamento
montado.
• O hardware de montagem incluído com este produto pode não ser
adequado para algumas estruturas de parede. Se não tiver o conhecimento
necessário para xar este produto à estrutura de parede que está a usar,
contacte um prossional de construção para fazer a instalação em parede ou
para fornecer instruções de montagem especícas para a sua estrutura de
parede.
Varningsmeddelanden
• Se till att du monterar produkten i enlighet med instruktionerna. Om du inte
gör det kan skada på person eller egendom uppstå.
• Använd aldrig produkten om delar saknas eller är skadade.
• Eftersom väggstrukturer varierar är det viktigt att kontrollera att
väggstrukturen och monteringsutrustningen som du använder klarar av
iv
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
den monterade utrustningen. Om du inte gör det kan skada på person och/
eller utrustning uppstå. Väggstrukturen ska kunna klara av minst fyra gånger
vikten av den monterade utrustningen.
• Monteringsutrustningen som medföljer produkten kanske inte är lämplig för
vissa väggstrukturer. Om du saknar nödvändiga kunskaper för att fästa denna
produkt på väggstrukturen som du använder, kontakta en professionell
konstruktör för att installera väggmonteringen eller för att ge specika
monteringsinstruktioner för din väggstruktur.
Advertencias de Uso
• Asegúrese de ensamblar este producto según las instrucciones. De lo
contrario, pueden producirse lesiones personales o daños en la propiedad.
• Nunca opere o ponga en funcionamiento este producto si faltan piezas o hay
daños en las mismas.
• Las estructuras de las paredes pueden variar y, por tanto, es importante
determinar con certeza que el tipo de estructura de la pared y el hardware
de montaje que se va a utilizar puedan soportar debidamente el equipo. De
lo contrario, se pueden producir lesiones personales o daños en el mismo. La
estructura de la pared debe ser capaz de soportar al menos cuatro veces el
peso del componente instalado.
• El hardware de montaje incluido con este producto puede no ser adecuado
para algunas estructuras de pared. Si no tiene la experiencia suciente para
jar este producto a la estructura de la pared correspondiente, póngase en
contacto con un profesional de la construcción para instalar el soporte de
pared o para que le proporcione las instrucciones especícas de montaje
para su estructura de pared.
Avertissements
• Assemblez ce produit conformément aux instructions. Si vous ne respectez
pas ces instructions, vous risquez de vous blesser ou d’endommager
l’équipement.
• N’utilisez pas ce produit si des pièces sont endommagées ou manquantes.
• Les structures des murs varient. Vous devez impérativement vérier que
le type de mur et le matériel de xation que vous utilisez permettent de
soutenir correctement l’équipement. Dans le cas contraire, vous risquez des
blessures corporelles ou des dommages matériels. La structure du mur doit
pouvoir supporter au moins quatre fois le poids de l’équipement monté.
• Le matériel de xation inclus avec ce produit n’est pas forcément approprié
pour toutes les structures de murs. Si vous ne disposez pas des compétences
v
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
nécessaires pour installer ce produit au mur, contactez un professionnel
an qu’il installe le support mural ou qu’il vous fournisse les instructions de
montage spéciques à votre structure de mur.
Waarschuwingen
• Zorg dat dit product volgens de instructies in elkaar wordt gezet. Indien dit
niet goed gebeurt kan lichamelijk letsel of materiële schade ontstaan.
• Gebruik dit product nooit als er onderdelen ontbreken of beschadigd zijn.
• Omdat wanden verschillen, is het belangrijk dat u ervoor zorgt dat het type
wandstructuur en de montagemiddelen die u gebruikt de gemonteerde
apparatuur goed ondersteunen. Indien u dit niet doet kan lichamelijk
letsel en/of schade aan de apparatuur ontstaan. De wandstructuur moet
voldoende zijn om ten minste vier keer het gewicht van de gemonteerde
apparatuur te ondersteunen.
• De bij dit product geleverde montagemiddelen kunnen niet geschikt zijn
voor sommige wandstructuren. Als u onvoldoende kennis hebt om dit
product aan de door u gebruikte wandstructuur te bevestigen, neem dan
contact op met een bouwkundige om de steun aan de muur te installeren of
specieke montage-instructies voor uw wandstructuur te geven.
Warnhinweise
• Montieren Sie dieses Produkt gemäß den Anweisungen. Anderenfalls kann
dies zu Verletzungen von Personen oder Schäden an Eigentum führen.
• Das Produkt darf nicht bedient werden, wenn Teile fehlen oder beschädigt
sind.
• Wandstrukturen unterscheiden sich, und es muss sichergestellt werden,
dass die Wand und das verwendete Montagematerial das montierte Gerät
halten kann. Anderenfalls kann dies zu Verletzungen von Personen und/oder
Schäden an Geräten führen. Die Wand muss mindestens das Vierfache des
Gewichts des montierten Geräts halten können.
• Das mitgelieferte Montagematerial ist möglicherweise nicht für jede Wand
geeignet. Wenn Ihnen die nötigen Fachkenntnisse zum Anbringen dieses
Produkts an einer Wand fehlen, lassen Sie einen Fachmann den Wandhalter
anbringen, oder lassen Sie sich von einem Fachmann Montageanweisungen
für Ihre Wand erteilen.
vi
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
注意
• 必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤
った場合に、傷害を負う恐れや物的損害が発生する恐れがあります。
• 本製品で使用している部品の一部が紛失していたり損傷している状態で使
用するのは絶対に止めて下さい。
• 壁の構造はお客様の環境ごとに異なります。ご使用になる壁の構造タイプ
と取付け金具が、取り付けモニターを確実に支持することを確認して下さ
い。確認を怠った場合、傷害を負う恐れや物的損害が発生する恐れがあり
ます。壁の構造が、取り付けるモニター重量の最低４倍まで支持できるだけ
の強度を持っていなければなりません。
• 本製品に同梱されている取付け金具は、ご使用になる壁の構造に対して十
分ではない場合があります。本製品を壁面に取り付ける時、十分な専門知
識が不足していると判断された場合、専門業者に連絡を取って、本製品の取
り付けを行ってもらうか、お客様の壁の構造に適した取り付け方法を教えて
もらってから取り付けを行って下さい。
Dichiarazioni di avvertenza
• Assemblare il prodotto rispettando le istruzioni. Il mancato rispetto delle
istruzioni potrebbe causare danni a persone o proprietà.
• Non utilizzare il prodotto in presenza di parti mancanti o danneggiate.
• Le caratteristiche dei muri sono variabili ed è importante vericare che
la struttura muraria e l’hardware di montaggio in uso siano in grado di
supportare adeguatamente le apparecchiature montate. Il mancato rispetto
delle istruzioni potrebbe causare danni a persone o proprietà. La struttura
muraria deve essere in grado di supportare un peso almeno quattro volte
superiore a quello dell’apparecchiatura montata.
• L’hardware di montaggio incluso con il prodotto potrebbe non essere
adeguato ad alcune strutture murarie. Se l’utente non dispone delle
competenze necessarie per agganciare il prodotto alla struttura muraria
in uso, dovrà contattare un professionista edile per installare il supporto a
parete o ottenere istruzioni di montaggio per la struttura muraria in uso.
Table of Contents
Compliance Statements ................................................................................... i
Safety Statements .............................................................................................. ii
Warning Statements .......................................................................................... iii
Product Diagram ................................................................................................1
Front-Side View .......................................................................................................................................... 1
Rear-Side View ............................................................................................................................................ 2
Adjustment Knobs .................................................................................................................................... 3
Product Dimensions .......................................................................................... 4
Product Information .......................................................................................... 5
Package Contents .....................................................................................................................................5
Technical Specications ................................................................................... 8
Installation ............................................................................................................ 9
Fasten the Wall Bracket to a Wall ......................................................................................................... 9
Attach the Mounting Arms .................................................................................................................... 10
Attach the Adjustment Module ........................................................................................................... 12
Attach the Projector Mount Assembly .............................................................................................. 13
Cable Management ................................................................................................................................. 17
Operation .............................................................................................................. 18
Adjust the Wall Mount Tilt Angle ......................................................................................................... 18
Adjust the Swivel .......................................................................................................................................19
Adjust the Tilt .............................................................................................................................................. 20
Adjust the Rotation .................................................................................................................................. 21
Adjust the Horizontal Lateral Position ............................................................................................... 22
Warranty Information ....................................................................................... 23
1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Front-Side View
Pole End Cap
Upper
Decorative
Cover
Lower
Decorative
Cover
Mounting Arm
Covers
Projector Pole
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Rear-Side View
Wall Bracket
Adjustment
Module
3
Adjustment Knobs
1) Tilt
Turn clockwise to adjust the picture down.
Turn counterclockwise to adjust the picture up.
2 ) Rotate
Turn clockwise to adjust the picture counterclockwise.
Turn counterclockwise to adjust the picture clockwise.
3) Swivel
Turn clockwise to adjust the picture to the right.
Turn counterclockwise to adjust the picture to the left.
Note: An Adjustment Screw must be loosened before the
Grey Adjustment Knob can be turned. See the Adjust the
Swivel Angle section for more information.
12
3
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Dimensions
Note: All measurements are listed in millimeters.
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
Wall Bracket
Qty: 1
Projector Pole
Qty: 1
Pole End Cap
Qty: 1
Upper Decorative
Wall Cover
Qty: 1
Lower Decorative
Wall Cover
Qty: 1
Adjustment
Module
Qty: 1
Right
Adjustment
Module Cover
Qty: 1
Left Adjustment
Module Cover
Qty: 1
Mounting Arms
Qty: 4
Mounting Arm
Covers
Qty: 4
Hinge Connector
Qty: 1
Wall Anchors
Qty: 6
6
Mounting Screws
Qty: 6
Washers
Qty: 4
10 mm Wrench
Qty: 1
5 mm Hex Key
Qty: 1
M3 x 24 mm
Screws
M4 x 24 mm
Screws
M5 x 24 mm
Screws
M6 x 24 mm
Screws
Qty: 4 (Of Each)
M6 x 8 mm Hex
Screws
Qty: 4 (Of Each)
M6 x 10 mm
Screws
Qty: 2
M6 x 25 mm
Hex Screw
Qty: 1
Nuts
Qty: 4
User Manual
Qty: 1
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Requirements
• Phillips Head Screwdriver
• Spirit/Bubble Level
• Mounting Surface
• (Optional) Two People for the Installation
8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Technical Specications
Type of Measurement Measurement
Weight Capacity
Up to 33.1 lb. (15 kg)
Tilt
+5 to -5
Swivel
+10 to -10
Horizontal Movement
+20 mm to -20 mm
kg
9
Installation
Fasten the Wall Bracket to a Wall
Warning! The Universal Projector Wall Mount is
designed to be installed on a wood stud, solid concrete, or
cinder block wall. The wall structure should be capable of
supporting at least four times the weight of the mounted
equipment. The Mounting Hardware included with this
product may not be adequate for installation on certain
wall structures. Contact a construction professional to install
the Universal Projector Wall Mount. Failure to do so may
result in personal injury and/or equipment damage.
PROJWALLMNT can be mounted using the included Mounting
Hardware. Ensure the top of the Wall Bracket is level with
a Spirit/Bubble Level before fastening it to the Mounting
Surface.
Cable Routing
1. Route the Power and Video Cables through the Projector
Pole. (Figure 1)
Figure 1
Wall Mount
Projector Pole
10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. (Optional, For In-Wall Cable Management) Feed the Power
and Video Cables into the Wall. Connect the Power Cable
to an available Power Source. Connect the Video Cable to
the Video Source Device.
3. Press the Projector Pole into the Wall Mount and hold the
Projector Pole in place. Align the four holes in the Projector
Pole with the four holes in the Wall Mount.
Attach the Projector Pole to the Wall Mount
• Thread the four M6 x 8 mm Hex Screws through the Wall
Mount and into the Projector Pole. Tighten using the 5 mm
Hex Key.
(Figure 2)
Attach the Mounting Arms
1. Place the Projector on a at and level Surface, with the
Mounting Holes facing upwards.
Figure 2
Wall Mount
Projector Pole
M6 x 8 mm Screws
11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Place the four Mounting Arms onto the Projector, with
the tubular portion of the Mounting Arms aligned over the
Mounting Holes in the Projector. (Figure 3)
Note: The threads of the Variable Position Screws, that are
built into the Mounting Arms, should be facing upwards.
3. Thread the appropriately sized M-Type Screws (e.g. M4 x
24 mm Screws) through the Mounting Arms and into the
Projector.
4. Tighten the M-Type Screws with a Phillips Head
Screwdriver.
Warning! Do not over-tighten the M-Type Screws. If you
encounter any unexpected resistance, immediately stop and
attempt to use a dierent length of M-Type Screw.
Figure 3
Projector
Mounting Arm
Mounting Arm Cover
Variable Position Screw
Figure 4 Nut
Mounting Arm
Cover
Washer
Variable Position
Screw
Adjustment Module
12
5. Place the Mounting Arm Covers over the Mounting Arms.
Attach the Adjustment Module
1. Place the Adjustment Module onto the Mounting Arms.
Align the Variable Position Screws with the cutouts in the
Adjustment Module. (Figure 4)
Note: If the Adjustment Module does not t onto the
Mounting Arms, loosen the M-Type Screws with a Phillips
Head Screwdriver and readjust the position of the
Mounting Arms. Tighten the M-Type Screws once the
correct position has been achieved.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
13
2. Place the four Washers over the Variable Position Screws.
3. Thread the four Nuts onto the Variable Position Screws.
Tighten using the 10 mm Wrench.
4. Attach the Right and Left Adjustment Module Covers by
sliding the Covers together over the Adjustment Module
until the two Covers snap together. (Figure 5)
Note: To remove these Adjustment Module Covers, locate
the labels that say Open. Apply pressure to one of these
labels while pulling the two Covers apart. Repeat for the
other side.
Attach the Projector Mount Assembly
1. Place the Hinge Connector onto the Adjustment Module.
Align the holes in the Hinge Connector with the holes in the
Adjustment Module.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Figure 5
Right
Adjustment
Module Cover
Left
Adjustment
Module Cover
14
2. Thread the two M6 x 10 mm Screws through the
Adjustment Module and into the Hinge Connector. Hand
tighten the M6 x 10 mm Screws by one rotation. (Figure 6)
Note: There must be a 2-3 mm gap between the Adjustment
Module and the Hinge Connector in order to complete the
following installation steps.
3. Slide the Projector Mount Assembly onto the Projector
Pole. Ensure the grooves in the Projector Pole are aligned
with the 2-3 mm gap created in Step 2. Ensure the weight of
the Projector is supported during this step. (Figure 7)
Figure 7
Projector Pole
Projector
Mount
Assembly
Figure 6
Adjustment
Module
Hinge Connector
M6 x 10 mm Screw
10 mm Wrench
15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
4. Tighten the M6 x 10 mm Screws that were threaded
through the Adjustment Module and Hinge Connector in
Step 2 using the 10 mm Wrench. (Figure 8)
5. Attach the Power and Video Cables to the Projector.
(Figure 9)
Figure 8 M6 x 10 mm Screw
10 mm Wrench
Figure 9
Power
and Video
Cables
16
6. Insert the Pole End Cap into the Projector Pole until it
snaps into place. (Figure 10)
Note: Pinch the sides and top of the Pole End Cap during
insertion.
7. Adjust the length of the Projector Pole by pulling apart to
lengthen and pushing together to shorten. Tighten the two
5 mm Hex Bolts located underneath, using the 5 mm Hex
Key. (Figure 11)
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Figure 10
Pole End Cap
Projector Pole
17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Cable Management
1. Ensure the Power and Video Cables have been connected
to the Projector.
(Optional) For On-Wall Cable Management
2. Determine if the Power and Video Cables will be routed out
of the Upper or Lower Decorative Cover.
3. Break away the Plastic Tab on the Decorative Cover that
was chosen in Step 2. (Figure 12)
Figure 11
5 mm Hex Key
5 mm Hex
Bolts
Projector Pole
18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
4. Slide the Upper and Lower Decorative Covers together,
over the Wall Bracket, until the two Covers snap into place.
Note: To remove these Decorative Covers, press the sides at
the top of the Lower Decorative Cover and pull apart.
5. Connect the Power Cable to an available Power Source.
Connect the Video Cable to the Video Source Device.
Operation
Adjust the Wall Mount Tilt Angle
1. Remove the Upper and Lower Decorative Covers.
Note: To remove these Decorative Covers, press the sides at
the top of the Lower Decorative Cover and pull apart.
Figure 12
Plastic
Tab
Upper Decorative
Cover
Lower Decorative Cover
19
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Loosen the four M6 x 8 mm Hex Screws on the side of the
Wall Mount, using the 5 mm Hex Key.
3. Insert the M6 x 25 mm Hex Screw into the hole in the Wall
Mount and tighten (angle up) or loosen (angle down), using
the 5 mm Hex Key until the desired angle is met. (Figure 13)
4. Tighten the four M6 x 8 mm Hex Screws on the side of the
Wall Mount, using the 5 mm Hex Key.
5. Slide the Upper and Lower Decorative Covers together,
over the Wall Bracket, until the two Covers snap into place.
Adjust the Swivel
1. Loosen the Adjustment Screw, located next to the Grey
Adjustment Knob, using the 10 mm Wrench.
Figure 13
M6 x 25 mm Hex Screw
M6 x 8 mm
Hex Screws
20
2. Turn the Grey Adjustment Knob in a Clockwise direction
to adjust the Projected Image to the right.
- or -
Turn the Grey Adjustment Knob in a Counterclockwise
direction to adjust the Projected Image to the left. (Figure
14)
3. Tighten the Adjustment Screw, located next to the Grey
Adjustment Knob, using the 10 mm Wrench.
Adjust the Tilt
• Turn the Yellow Adjustment Knob in a Clockwise direction
to adjust the Projected Image down.
- or -
• Turn the Yellow Adjustment Knob in a Counterclockwise
direction to adjust the Projected Image up. (Figure 15)
Figure 14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
21
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Adjust the Rotation
• Turn the Black Adjustment Knob in a Clockwise direction
to rotate the Projected Image counterclockwise.
- or -
• Turn the Black Adjustment Knob in a Counterclockwise
direction to rotate the Projected Image clockwise. (Figure 16)
Figure 15
Figure 16
22
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Adjust the Horizontal Lateral Position
1. Loosen the two Adjustment Screws located on the top of
the Adjustment Module, using the 10 mm Wrench.
2. Slide the Projector Mount Assembly to the left or the right
to adjust the Projected Image to the left or right. (Figure 17)
3. Tighten the two Adjustment Screws located on the top of
the Adjustment Module, using the 10 mm Wrench.
Figure 17
Adjustment Screw
10 mm Wrench
23
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or
their ocers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of
prots, loss of business, or any pecuniary loss, arising out of or related to the use
of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle
15 Gowerton Rd.,
Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support