Table of Contents
StarTech.com S322SAT3R User Manual
Displayed below is the user manual for S322SAT3R by StarTech.com which is a product in the Interface Cards/Adapters category. This manual has pages.
Related Manuals
Manual Revision: 05/09/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
S322SAT3R
Internal Drive Mounted Dual SATA Hard
Drive RAID Adapter
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View ...................................................................................................................................................... 1
Introduction ............................................................................................ 2
Packaging Contents ................................................................................................................................. 2
System Requirements ..............................................................................................................................2
Installation ..............................................................................................2
Hardware Installation ..............................................................................................................................2
Congure RAID .......................................................................................6
RAID Lock/Unlock Jumper Pins ............................................................................................................6
LED Activity and Drive Failure Indicators ........................................... 8
Hard Drive Initialization ........................................................................8
Specications .......................................................................................... 10
Technical Support ..................................................................................11
Warranty Information ............................................................................ 11
Instruction Manual
1
Product Diagram
Front View
Rear View
Drive #1 SATA (DATA + Power) connector
2-pin LED connector
for HDD Activity LED
4-pin power
connector
SATA host interface
connector
Drive #2 SATA
(DATA) connector
RAID setting
jumper pins
RAID unlock/
lock jumper
pins
Instruction Manual
2
Introduction
Packaging Contents
• 1x Internal Drive Mounted Dual SATA Hard Drive RAID Adapter (S322SAT3R)
• 2x SATA Cable (50cm)
• 1x 4-pin to SATA Power Adapter
• 1x Installation Manual
System Requirements
• 2 x 2.5/3.5” SATA Hard Drives or Solid State Drives (HDD/SSD)
• 1 x Computer System with:
• 1x Available SATA Interface Connection
• 2 x Available SATA Power Source
Installation
Hardware Installation
WARNING! Hard drives, internal computer system components, and RAID adapters
require careful handling. If you are not careful with your hard drive, lost data may
result. Always handle your computer equipment with caution. Be sure that you
are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
Note: Before you begin installation open your computer system and remove any SATA
or Data or power cables connected to the drives you intent to build in your RAID array.
WARNING! Setting or changing your RAID modes may erase all data or metadata
on your existing HDD/SSDs. It is recommended you backup any existing data before
attaching your hard drives to the S322SAT3R RAID Adapter.
1. Set the RAID unlock/lock jumper pins to the unlock position, and set your desired
RAID conguration. (See: Congure RAID).
Instruction Manual
3
2. Connect the Drive #1 SATA (DATA + Power) connector on the S322SAT3R to the
SATA (DATA+Power) connector on the rst HDD/SSD mounted in your Computer
System.
3. Using one of the included SATA Cables, connect the SATA (Data) connector on the
second HDD/SSD to the Drive #2 SATA (DATA) connector on the S322SAT3R.
4. Connect an available SATA Power Source in your Computer System to the SATA
(Power) connector on the second HDD/SSD.
Instruction Manual
4
5. Using the remaining included SATA Cable, connect the SATA Host Interface
connector on the S322SAT3R to an available SATA Interface on your Computer
System.
Instruction Manual
5
6. Using the included 4-pin to SATA Power Adapter, connect the 4-pin power
connector on the S322SAT3R to an available SATA Power Source in your
Computer System.
7. The S322SAT3R is now been installed, close your computer case and start your
computer to build the RAID array.
8. (Optional) If you would prefer to lock your RAID array so it cannot be altered by the
RAID mode setting jumper pins, power down and open your computer system, and
set the RAID Lock/Unlock Jumper Pins to the lock position. (See Congure RAID).
The computer system can then be closed and powered back on.
Instruction Manual
6
Congure RAID
WARNING! Setting or changing your RAID modes may erase all data or metadata on
your existing HDD/SSDs.
RAID Lock/Unlock Jumper Pins
The RAID lock/unlock jumper pins, located above the drive mounting brackets
enable you to lock your RAID conguration so it cannot be changed. Or unlock your
conguration so it can be changed.
Use the included jumper and the table below, to short the pins and set the mode for
your desired conguration.
GND
SET
NC
Mode Description Jumper Pins
Unlocked Enables you to change your RAID
conguration mode. GND-SET
Locked Does not allow you to change your RAID
conguration mode. SET-NC
RAID Mode Setting Jumper Pins
The RAID setting jumper pins, located next to the SATA connector enable you to set
your desired RAID conguration between RAID 0, RAID 1, JBOD, and RAID initial Mode.
1
2
3
4
5
6
Instruction Manual
7
Use the included jumpers and the table below, to short the pins and set your desired
RAID mode.
RAID Mode Description Short Pins
RAID 0 Striping - Improves system performance 1-2, 4-5
RAID 1 Mirror – Creates a redundant drive on the
second drive for security 2-3, 4-5
BIG Spanning – Creates a large single drive
volume consisting of both drives. 1-2, 5-6
JBOD
Just a Bunch of Disks – Allows access to both
drives individually
(Note: A port multiplier compatible SATA
controller is required for this mode)
2-3, 5-6
Set RAID Conguration
1. Set the RAID Lock/Unlock Jumper Pins to the unlock position.
2. Using the RAID Mode setting jumper pins to your desired Mode.
3. Your RAID array has now been installed.
4. (Optional) If you would prefer to lock your RAID array so it cannot be altered by the
RAID mode setting jumper pins, power down your SATA host device, and set the
RAID Lock/Unlock Jumper Pins to the lock position.
Instruction Manual
8
LED Activity and Drive Failure Indicators
The S322SAT3R includes a 2-pin LED connector for HDD Activity LED enabling you to
visually monitor drive activity and RAID array health. Please review the table below for
a list of each specic indication.
Description LED Activity
Adapter powered on and RAID status
healthy O
HDD Activity Flashing LED (Short Flash with DATA
bursts)
Degraded array / failed RAID Solid Bright LED
RAID rebuilding Pulsing LED (Long 1 second ash with
between 1 second pauses)
RAID rebuild complete O
Hard Drive Initialization
If the HDD/SSD RAID Array is new or otherwise blank, it may need to be initialized and
formatted before use. Follow the steps below in a Windows interface to initialize the
drive.
1. From the main Windows desktop, right-click on “My Computer” (“Computer” in Vista/
7 / 8), then select Manage. In the new Computer Management window, select Disk
Management from the left window panel.
Instruction Manual
9
2. A dialog window should automatically appear, asking you to initialize the drive.
Depending on the version of Windows, it will give you the option of either creating
an “MBR” or “GPT” disk. GPT (GUID partition) is required for drives volumes larger
than 2TB. However, it is not compatible with some older operating systems, while
MBR is supported by newer and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard
drive capacity to conrm it’s the correct hard drive) and then right-click in the
section that says “Unallocated” and select “New Partition”.
4. Follow the on screen prompts to initialize the drive in the format of your choice.
Instruction Manual
10
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.