Table of Contents
StarTech.com SAT32M225 User Manual
Displayed below is the user manual for SAT32M225 by StarTech.com which is a product in the Interface Cards/Adapters category. This manual has pages.
Related Manuals
Manual Revision: 12/19/2013
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
SAT32M225
M.2 NGFF SSD to 2.5in SATA SSD Converter
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View ...................................................................................................................................................... 1
Introduction ............................................................................................ 2
Packaging Contents ................................................................................................................................. 2
System Requirements ..............................................................................................................................2
M.2 NGFF SSD Installation ....................................................................2
Hard Drive Initialization ........................................................................5
Technical Support ..................................................................................7
Warranty Information ............................................................................ 7
Instruction Manual
1
Product Diagram
Front View
Rear View
1. SATA DATA & Power Combo (7+15 pin)
2. Side mounting holes
1. M.2 (NGFF) SSD Connector
2. Drive installation bracket
3. Drive length adjustment holes
4. Top mounting holes
Instruction Manual
2
Introduction
Packaging Contents
• 1 x M.2 NGFF SSD to 2.5in SATA SSD Converter
• 1 x Mounting screw kit
• 1 x Installation manual
System Requirements
• M.2 NGFF Drive
• SATA Host Device
M.2 NGFF SSD Installation
WARNING! SSD Drives and storage adapters require careful handling. If you are
not careful with your SSD Drive, lost data may result. Always handle your drive with
caution. Be sure that you are properly grounded by wearing an anti-static strap when
handling computer components or discharge yourself of any static electricity build-up
by touching a large grounded metal surface (such as the computer case) for several
seconds.
1. Determine if the drive installation bracket requires relocating by assessing your
drive length. The board is labeled with the respective drive types for length but if
your drive type is unknown,place your SSD next to the M.2 (NGFF) SSD connector,
note which drive installation hole matches the height of your SSD. If the bracket is
already installed in the correct position please proceed to step 4.
Instruction Manual
3
2. (Only required if the drive installation bracket requires relocating) Remove the
screw holding the bracket in place on the reverse side using a Philips head screw
driver (Not included).
Note: There are screws located on either side of the bracket, ensure the reverse
screw is the one removed, see photo below.
3. (Only required if the drive installation bracket requires relocating) Reseat
the drive installation bracket in the drive installation hole that matches your SSD.
Replace the removed screw on the reverse side by driving it into place using a
phillips head screw driver.
Instruction Manual
4
4. Using a Phillips head screw driver (not included). Remove the screw located in the
front of the hard drive installation bracket.
Note: There are screws located on either side of the bracket, ensure the front screw
is the one removed, see photo below.
5. Slide the M.2 connector on the SSD into the M.2 receprical connector on the
SAT32M225.
Note: The connector on your M.2 SSD is keyed so the drive will only t one way.
6. Press the drive down toward the drive mounting bracket, and drive the removed
screw through the mounting hole on your SSD drive and into the drive mounting
bracket using a Philips head screw driver.
Instruction Manual
5
7. The SSD has now been installed, and is ready to be implemented in your 2.5” SATA
drive application.
Refer to the manual for your SATA host device for installation instructions. The top or
side mounting holes and included screw kit may or may not be required to assist in
your installation.
Hard Drive Initialization
If the M.2 SSD is new or otherwise blank, it may need to be initialized and formatted
before use. Follow the steps below in a Windows interface to initialize the drive.
1. From the main Windows desktop, right-click on “My Computer” (“Computer” in
Vista/ 7 / 8), then select Manage. In the new Computer Management window, select
Disk Management from the left window panel.
Instruction Manual
6
2. A dialog window should automatically appear, asking you to initialize the drive.
Depending on the version of Windows, it will give you the option of either creating
an “MBR” or “GPT” disk. GPT (GUID partition) is not compatible with some older
operating systems, while MBR is supported by newer and older operating systems.
3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard
drive capacity to conrm it’s the correct hard drive) and then right-click in the
section that says “Unallocated” and select “New Partition”.
4. Follow the on screen prompts to initialize the drive in the format of your choice.
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.