Table of Contents
StarTech.com SATSASBP125 User Manual
Displayed below is the user manual for SATSASBP125 by StarTech.com which is a product in the Drive Bay Panels category. This manual has pages.
Related Manuals
Manual Revision: 03/20/2018
For the most up-to-date information, please visit: www.startech.com
FR: Guide de l’utilisateur - fr.startech.com
DE: Bedienungsanleitung - de.startech.com
ES: Guía del usuario - es.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
IT: Guida per l’uso - it.startech.com
JP: 取扱説明書 - jp.startech.com
SATSASBP125
1-Bay 2.5in SATA/SAS Hard Drive Backplane
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Front View .................................................................................................................................................... 1
Rear View ...................................................................................................................................................... 1
Introduction ............................................................................................ 2
Packaging Contents ................................................................................................................................. 2
System Requirements ..............................................................................................................................2
Hardware Installation ............................................................................3
Hard Drive Installation ..........................................................................4
Specications .......................................................................................... 8
Technical Support ..................................................................................9
Warranty Information ............................................................................ 9
Instruction Manual
1
Product Diagram
Front View
Rear View
1. Power button
2. 1x 2.5” Drive bay/tray
3. 1x 2.5” Drive bay key hole
4. 1x Drive Tray Release Latches
1. 1x SATA power connector port
2. 1x SATA data connector port
Instruction Manual
2
Introduction
Packaging Contents
• 1x 1-Bay 2.5in SATA/SAS Hard Drive Backplane
• 2x Drive bay keys
• 1x 2.5” HDD/SSD Drive Tray
• 1x SATA cable
• 4x Drive mounting screw kit
• 4x Backplane mounting screw kit
• 1x Instruction Manual
System Requirements
• 1x 2.5in SATA/SAS hard drive
Computer System:
• 1x SATA/SAS host connector port
• 1x Available 3.5” bay
• 1x Available SATA power connection
Instruction Manual
3
WARNING! Hard drives and storage docks require careful handling, especially when
being transported. If you are not careful with your hard disk, lost data may result.
Always handle your hard drive and storage device with caution. Be sure that you
are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
Hardware Installation
1. Ensure your computer system is powered down, and the power cable has been
disconnected from the Power Supply.
2. Open your computer case (refer to the computer user manual for details), and place
the 2.5in SATA/SAS HDD Backplane into the 3.5” slot, lining up the side installation
holes on the Backplane (pictured below), with installation holes on the 3. 5” slot
inside the computer.
3. Hold the Backplane into place, and x the four included drive bay screws (black)
through the installation holes on the 3.5” bay, into the side installation holes on the
Backplane.
Notes:
• While only four mounting points are required (two on either side), six mounting
holes are available to accommodate dierent styles of computer cases.
• Installation steps may vary depending on your computer case, refer to the
computer case user manual for details.
Instruction Manual
4
4. Connect the included SATA data cable from an available SATA/SAS host ports
on your motherboard to the SATA/SAS data connector port on the back of the
Backplane.
5. Connect a SATA Power connector from your power supply to the SATA power
connector port on the back of the backplane.
Hard Drive Installation
1. To remove the tray, squeeze the latch to release the door handle, pull the tray door
handle open and slide the tray out of the enclosure.
Note: If the drive is locked, insert either of the included bay keys into the 2.5in drive
bay key hole, and turn the key clockwise into the unlock position before attempting
to remove the tray.
2. Insert your desired drive into the drive tray with the bottom mounting drive holes
in line with the mounting holes on the drive tray. Fix the drive to the drive tray using
four of the included drive screws (silver).
Instruction Manual
5
3. Slide the drive tray with installed hard drive back into the slot and close the door.
Instruction Manual
6
4. (Optional) If you would like to lock the drive door for added security, use the key to
turn the key counter clockwise into the locked position.
Instruction Manual
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.