StarTech.com SHELF-1U-12-FIXED-S User Manual
Displayed below is the user manual for SHELF-1U-12-FIXED-S by StarTech.com which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: July 16, 2021 4:40 PM
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
1 1
Product IDs
SHELF-1U-12-FIXED-S
SHELF-1U-12-FIXED-V
SHELF-1U-20-FIXED-S
SHELF-1U-20-FIXED-V
Product Diagrams
Front - Angled View
Solid Vented
Component Function
1Mounting Holes • Mount the 1U Solid/Vented Shelf into a Rack or Cabinet.
2Shelf Lip
• Mount the 1U Solid/Vented Shelf with the Shelf Lip
oriented downwards to prevent Equipment from catching
during storage and/or retrieval
Product Information
For the latest manuals, product information, technical specications, and declarations
of conformance, please visit:
www.StarTech.com/SHELF-1U-12-FIXED-S
www.StarTech.com/SHELF-1U-12-FIXED-V
www.StarTech.com/SHELF-1U-20-FIXED-S
www.StarTech.com/SHELF-1U-20-FIXED-V
Requirements
• 1U Available Rack Space
1U Solid/Vented Cantilever Shelf - 12/20 in. Depth
Warnings
• Read the entire manual and ensure the instructions are fully understood before
assembling and/or using this product.
• Before adding equipment to this product, ensure this product has been properly
mounted.
• Ensure the weight of the equipment does not exceed the weight capacity of this
product. If the weight capacity is exceeded, personal injury or damage to the
equipment are possibilities. This product can support the following weight: up
to 55 lb. (25 kg). This product can only support the maximum weight capacity if 4
M6 Screws / Cage Nuts / Plastic Washers are used to ax this product to a rack or
cabinet.
Package Contents
• 1U Solid/Vented Shelf x 1
• M6 Cage Nuts x 4
• M6 Screws x 4
• M6 Plastic Washers x 4
• Quick-Start Guide x 1
Installation
Mount the 1U Solid/Vented Shelf into a Rack or Cabinet
Use the included M6 Cage Nuts, M6 Screws, and M6 Plastic Washers to install the 1U
Solid/Vented Shelf.
Notes: This product can support the following weight: 55 lb. (25 kg).
The following installation instructions are for square mounting holes.
1. Locate a suitable location in a Rack or Cabinet to mount the 1U Solid/Vented
Shelf.
Note: The 1U Solid/Vented Shelf itself requires 1U of space within a Rack or
Cabinet.
2. Insert the Wing (side) of an M6 Cage Nut into the back of the a Cage Nut Hole.
3. Insert the second Wing of the M6 Cage Nut into the selected Cage Nut Hole, using
pressure by hand, or with a Cage Nut Tool.
4. Repeat steps 2 and 3 to insert a total of 4 Cage Nuts.
*Product may vary from images
22
5. Thread an M6 Plastic Washer over an M6 Screw. Repeat until 4 M6 Screw
Assemblies have been prepared.
6. Align the Mounting Holes in the 1U Solid/Vented Shelf with the M6 Cage Nuts
installed in steps 2-4.
7. Insert the M6 Screw Assemblies through the Mounting Holes in the 1U Solid/
Vented Shelf and into the M6 Cage Nuts and tighten, using a Phillips Head
Screwdriver.
Regulatory Compliance
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss
of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the
product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands