StarTech.com SV231DPUA User Manual
Displayed below is the user manual for SV231DPUA by StarTech.com which is a product in the KVM Switches category. This manual has pages.
Related Manuals
Manual Revision: 05/06/2016
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
*actual product may vary from photos
SV231DPUA / SV431DPUA
2/4 Port USB DisplayPort® KVM Switch with Audio
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction ...........................................................................................1
Features ........................................................................................................................................................ 1
Package Contents ....................................................................................................................................1
System Requirements ..............................................................................................................................1
Installation ..............................................................................................1
Hardware Installation ..............................................................................................................................2
Driver Installation ...................................................................................................................................... 5
Operation ................................................................................................5
Front Panel ................................................................................................................................................... 5
Port Selection Button .............................................................................................................................. 6
AutoScan ...................................................................................................................................................... 6
Scan Time ..................................................................................................................................................... 6
HotKey Control .......................................................................................6
Auto Scan ..................................................................................................................................................... 7
Manual Scan ............................................................................................................................................... 7
Alternative Hotkey Commands ............................................................................................................9
Change Leading Hotkey ......................................................................................................................... 10
Specications .......................................................................................... 11
Technical Support ..................................................................................13
Warranty Information ............................................................................ 13
Instruction Manual
1
Introduction
Features
• Easy installation, no drivers required
• Supports Plug and Play and hot swap to save time from rebooting the computer
• Supports data transfer rates up to 480Mbps when used on a USB 2.0 port
Package Contents
• 1 x SV231DPUA or SV431DPUA KVM switch
• 4 x foot pads
• 1 x universal power adapter (NA/UK/EU/AU)
• 1 x instruction manual
System Requirements
• DisplayPort enabled computer system/video card
• USB enabled computer system
• DisplayPort enabled display device (e.g. monitor, projector, TV, etc.)
• Standard 104-key wired USB keyboard
• Standard 3-button wired USB mouse
Installation
NOTE: Prior to the installation, please power o all devices that will be connected to
this system. Ensure that all devices you will connect are properly grounded. Place
cables away from uorescent lights, air conditioners, and machines that are likely to
generate electrical noise.
If you experience any problems using a USB KVM switch, the following BIOS setup
changes may be necessary for PC users and not necessary for Mac users:
• Set HALT ON ERROR to ALL BUT KEYBOARD.
• In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED.
Dierent systems may use dierent naming, so contact your system manufacturer for
further assistance with these settings.
Instruction Manual
2
Hardware Installation
Front View - SV231DPUA
Rear View - SV231DPUA
Port Selection/Link LED Port Selection
Button
Instruction Manual
3
Front View - SV431DPUA
Rear View - SV431DPUA
Power
LED
Port Selection
Button
Port Selection/Link
LED
Instruction Manual
4
*installation pictures are representations only
1. Plug a monitor into the Console’s DisplayPort connector; plug a USB keyboard and a
USB mouse into the dedicated USB keyboard and mouse ports on the KVM switch. If
using audio, also connect speakers and/or a microphone with 3.5mm mini-jack plugs.
2. Use a male-to-male DisplayPort video cable to connect the DisplayPort connector
on the computer’s video card, to one of the KVM’s PC ports (i.e. PC1)
3. Use a USB type A-B Cable to connect the KVM’s USB port (type B, square connector)
for the PC port used in Step 2, and the USB port on the computer (type A, at
connector). If using audio, connect 3.5mm mini-jack cables from the PC port to the
computer sound card.
NOTE: A DisplayPort + USB + Audio KVM combo cable is also available which can be
Instruction Manual
5
used in place of separate individual cables, StarTech.com ID: DP4N1USB6.
4. Repeat for Steps 2 and 3 for each PC port on the KVM switch, or each computer you
wish to use on the KVM.
5. OPTIONAL: Connect any other USB peripherals you wish to share between the
connected computers/devices to the extra USB Hub ports on the Console side.
6. Connect the external power adapter from a wall outlet to the power connector on
the rear panel of the KVM switch. The Power LED should light up solid and/or the
LED for the selected PC port.
7. Power up the rst computer/device and wait for it to fully boot and test keyboard/
mouse functionality.
8. Once operation has been successfully conrmed, switch to the next port and power
up that computer/device and conrm.
9. Once completed for all computers/devices connected to the KVM switch, you
should be able to switch between ports freely.
Driver Installation
No driver installation is required for the KVM switch, as the keyboard and mouse
use generic USB keyboard/mouse drivers that are already installed on any operating
system that fully supports USB.
Operation
Front Panel
Port Selection/Link LED
The LED turns green when the connected computer is powered-on. The corresponding
LED will also illuminate red when that PC port is currently selected.
Instruction Manual
6
Port Selection Button
2-Port: Pressing the front panel “Select” button will toggle between the two ports on
the KVM switch.
4-Port: Each push button on the front panel corresponds with a PC port. Pressing that
button will immediately select that port.
AutoScan
The system automatically scans through the power-on computers in sequence with a
xed interval (see Scan Time below).
4-Port: To activate AutoScan, press front panel push buttons “3” and “4” simultaneously.
The port selection LED will ash during AutoScan. AutoScan will select active
computers only. To exit AutoScan mode, just press any one of the front panel
push buttons.
Scan Time
Four options are available for users to set the Scan Time duration, it Includes 3, 8, 15
and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
4-Port: To change the Scan Time, press front panel buttons “1” and “2” simultaneously.
The unit will respond with beep(s) of 1, 2, 3 or 4 times for a Scan Time of 3, 8, 15
or 30 seconds respectively.
HotKey Control
A Hotkey command is a short keyboard sequence for selecting a computer, activating
computer scan, etc. A hotkey sequence starts with two left <CTRL> keystrokes
(successively within 0.2 seconds) followed by one or two more keystrokes. A built-in
tone generator creates a high-pitch beep for correct hotkey command; otherwise, one
low-pitch beep is generated for errors and the bad key sequence will not be forwarded
to the selected computer.
NOTE: Press and hold Left <SHIFT> and press <NumLock> twice, then release <SHIFT>
followed by pressing left <CTRL> once, which will enable / disable the hotkey feature.
Instruction Manual
7
To select a computer:
Left <CTRL> + Left <CTRL> + <1>
(Example: Selects the computer at port 1.)
Left <CTRL> + Left <CTRL> + <2>
(Example: Selects the computer at port 2.)
NOTE: Do not use the keypad on the right-side of the keyboard.
Auto Scan
The KVM automatically scans through the powered-on computers in sequence on a
xed time interval (see Scan Time below).
Note: The keyboard and mouse are not operable during Auto Scan.
To start Auto Scan:
Left <CTRL> + Left <CTRL> + <F1>
To abort the Auto Scan mode, press the left <CTRL> key twice. When Auto Scan detects
any keyboard or mouse activity, it suspends the scanning till the activity stops; it then
resumes with the next computer in sequence. The length of the Auto Scan interval
(Scan Time) is adjustable, see below.
Manual Scan
Manual Scan allows users to manualls switch back and forth between powered-on
computers.
Left <CTRL> + Left <CTRL> + <F2>
To select the previous or the next computer, press <UP> or <DOWN> arrow keys. To
abort the Manual Scan, press any other key.
Instruction Manual
8
Scan Time
Four options are available for users to set the Scan Time duration, it includes 3, 8, 15
and 30 seconds.
Note: Scan Time is set to 3 seconds by default.
To adjust Scan Rate, set the scan time of duration before switching to the next computer:
Left <CTRL> + Left <CTRL> + <F3>
The KVM Switch generates 1 to 4 beeps indicating a scan time duration for 3, 8, 15 or
30 seconds respectively.
Audio Lock
There are two options for Audio Lock: ON and OFF. When ON, audio selection follows
computer selection. When OFF, audio selection stops following computer selection. It
is useful if you want to listen to a particular computer’s audio signal while operating
other computers.
Left <CTRL> + Left <CTRL> + <F5>
The KVM switch beeps once or twice corresponding to ON and OFF respectively.
To change which computer port the audio stays on to the currently selected port, press
the following hotkey:
Left <CTRL> + Left <CTRL> + <A>
Instruction Manual
9
Alternative Hotkey Commands
In addition to the Left <CTRL> + Left <CTRL> hotkeys, there are two
alternative hotkey sequences available.
1. 1. For the following operations, users may press <ScrollLock> twice instead of
pressing left <CTRL> twice.
To select a computer:
<ScrollLock> + <ScrollLock> + <1>
(Example: Select the computer at port 1.)
<ScrollLock> + <ScrollLock> + <2>
(Example: Select the computer at port 2.)
NOTE: Do not use the keypad at the right of the keyboard.
Instruction Manual
10
2. For those keyboards that do not have or support <ScrollLock>, please press and
HOLD the Left <SHIFT> and press <NumLock> twice instead of pressing Left
<CTRL> twice.
To select a computer:
hold Left <SHIFT> + press <NumLock> + press <NumLock>
then release <SHIFT> + press <1>
Example: Select the computer at port 1.)
hold Left <SHIFT> + press <NumLock> + press <NumLock>
then release <SHIFT> + press <2>
(Example: Select the computer at port 2.)
NOTE: Do not use the keypad at the right of the keyboard.
Change Leading Hotkey
The default leading hotkey sequence involves pressing the left <CTRL> twice in
succession (e.g. left <CTRL> + left <CTRL>). This can be changed to the right <CTRL>
key instead, to avoid accidental activation due to using the left <CTRL> key for
functions such as Copy/Paste.
To change the leading hotkey sequence to Right <CTRL>:
Left <CTRL> + Left <CTRL> + hold <ALT> + press Right <CTRL>
All hotkey commands that previously required pressing the Left <CTRL> will be
switched to requiring the right <CTRL> instead.
To change the leading hotkey sequence back to Left <CTRL>:
Right <CTRL> + Right <CTRL> + hold <ALT> + press Left <CTRL>
Instruction Manual
11
Specications
SV231DPUA SV431DPUA
Number of Ports 2 4
Computer Connectors
(per port)
1 x DisplayPort
1 x USB type B
2 x 3.5mm mini-jack
Console Connectors
1 x DisplayPort
1 x USB type
2 x 3.5mm mini-jack
LEDs 2 x Port Select/Power 1 x Power
4 x Port Select/Power
Maximum Video
Resolution
2560 x 1600 @ 60Hz
(higher resolutions may be supports at lower refresh
rates)
Switching Modes Front Panel Button, Hotkey
Rack Mountable No Yes (optional kit)
Cascadable No
On Screen Display No
DDC2B Support Yes
Audio Yes
Enclosure Material Metal
Power Adapter 9-12VDC, 1.5A
Instruction Manual
12
SV231DPUA SV431DPUA
Operating
Temperature 0°C ~ 40°C (32°F ~ 104°F)
Storage Temperature -20°C ~ 60°C (-4°F ~ 140°F)
Humidity 0 ~ 80% RH
Dimensions (WxHxD) 160.0mm x 44.0mm x
100.0mm
220.7mm x 44.0mm x
130.6mm
Weight 1050g 1100g
Instruction Manual
13
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.