StarTech.com SV565HDIP User Manual
Displayed below is the user manual for SV565HDIP by StarTech.com which is a product in the KVM Switches category. This manual has pages.
Related Manuals
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: September 26, 2019 2:09 PM
Product Diagram (SV565HDIP)
Transmitter
Port Function
Transmitter
1Power Port • Used to connect the Universal Power Adapter
to the Transmitter.
2RJ45 Port • Used to connect the Transmitter to the
Receiver.
3HDMI Port • Used to connect a Video Source Device to the
Transmitter.
4Mini USB Port • Used to connect the Host Computer or KVM
Switch to the Transmitter.
Receiver
HDMI® KVM Extender | 4K 30Hz | 328 ft. (100 m)
1
Port Function
Receiver
5Power Port • Used to connect the Universal Power Adapter
to the Receiver.
6RJ45 Port • Used to connect the Receiver to the
Transmitter.
7HDMI Port • Used to connect a Display Device to the
Receiver.
8USB-A Port x 2 • Used to connect a USB Keyboard and/or
Mouse to the Receiver.
Requirements
For latest requirements and full product manual, visit www.startech.com/SV565HDIP.
Installation
Transmitter
1. Connect an HDMI Cable to the HDMI Port on the Transmitter and to an HDMI port
on the Host Computer, KVM Switch, or Video Source Device.
2. Connect a USB-A to Mini B Cable to the Mini USB Port on the Transmitter and to a
USB port on the Host Computer or KVM Switch.
3. Depending on the conguration of your devices use one of the connection methods
below:
• Direct connection: Connect a CAT5e/6 Cable to the RJ45 Port on the
Transmitter and connect the other end to the RJ45 Port on the Receiver.
• Indirect connection: Connect the CAT5e/6 Cable to an RJ45 Port on a Wall
Receptacle (pre-wired), or an Ethernet Switch.
4. Connect the Universal Power Adapter to the Power Port on the Transmitter and
to an AC Electrical Outlet.
2 3 4
5 6 78
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (A)/NMB-3(A)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
Changing the Rotary Dip Switch Channel
• On the Transmitter and Receiver, insert a Flathead Screwdriver into the Rotary
Dip Switch Slot and adjust the Rotary Dip Switch to the desired channel.
Note: Set the Transmitter and Receiver to the same Rotary Dip Switch channel.
Receiver
1. Connect a Keyboard and/or Mouse to the USB-A Ports x 2 on the Receiver.
2. Connect an HDMI Cable to the HDMI Port on the Receiver and connect the other
end to an HDMI port on the Display Device.
3. (Optional) Indirect connection: Connect a CAT5e/6 Cable to the RJ45 Port on
the Receiver and to an RJ45 Port on a Wall Receptacle (pre-wired) or an Ethernet
Switch.
4. Connect the Universal Power Adapter to the Power Port on the Receiver and the
to an AC Electrical Outlet.
Rotary Dip Switch
The Rotary Dip Switch is located on the front of the Transmitter and Receiver.
Rotary Dip Switch
If you are connecting additional Transmitters/Receivers, they all need to be set to the
same Rotary DIP Switch channel.
Note: By default the Rotary Dip Switches on the Transmitter and Receiver are set
to channel 0.