StarTech.com TB3DK2DPM2 User Manual
Displayed below is the user manual for TB3DK2DPM2 by StarTech.com which is a product in the Notebook Docks & Port Replicators category. This manual has pages.
Related Manuals
i
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
ii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
iii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでください。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements ................................................................................... i
Safety Statements .............................................................................................. iii
Product Diagram ................................................................................................1
Front View .................................................................................................................................................... 1
Rear View ...................................................................................................................................................... 1
Bottom View ................................................................................................................................................2
Product Information .......................................................................................... 2
Package Contents .....................................................................................................................................2
Requirements ............................................................................................................................................. 2
Installation ............................................................................................................ 4
Connecting .................................................................................................................................................. 4
Powering ...................................................................................................................................................... 10
Driver Installation ...................................................................................................................................... 10
Display Conguration ....................................................................................... 11
Connect HDMI, DVI and VGA Displays ............................................................................................... 11
Congure Displays ....................................................................................................................................12
Supported Video Resolutions ............................................................................................................... 12
Video Resolution and Bandwidth Allocation .................................................................................. 12
Operation .............................................................................................................. 14
LED Indicators............................................................................................................................................. 14
Charge a Device ......................................................................................................................................... 14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
1
Product Diagram
Actual product may vary from photos
Front View
Rear View
USB-C
(10Gbps)
Port
Ethernet
Port
Thunderbolt 3
Peripheral Port
Thunderbolt 3
Host Port
DC IN
20V
Power
Input
Port
USB-A
(5Gbps)
Port
SD Card
Reader
Slot
3.5 mm
Audio
Output
Port
3.5 mm
Microphone
Port
USB-A
(5Gbps)
Port
DisplayPort
Port
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2
Bottom View
Product Information
Package Contents
• Docking Station x 1
• Thunderbolt 3 Cable x 1
• Universal Power Adapter x 1
• Power Cords (NA/JP, EU, UK, ANZ) x 4
• Instruction Manual x 1
Requirements
For the latest requirements, please visit www.startech.com/TB3DK2DPM2.
Power:
• Available AC electrical outlet
M.2 SSD Slot
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3
Laptop:
• Host Laptop with an available Thunderbolt 3 Port (your Laptop’s Thunderbolt
3 port must support USB Power Delivery in order to power and charge your
Laptop) x 1
Display:
• DisplayPort Equipped Display x 1
• DisplayPort Cable (for an additional external display) x 1
• USB Type-C or Thunderbolt 3 Equipped Display x 1
• Thunderbolt 3 Cable (for an additional external display) x 1
Note: For dual-display congurations: Use the Docking Station’s Thunderbolt
3 Peripheral Port. You may need to purchase a separate adapter to connect
an HDMI, a DVI, or VGA display.
Note: For 4K x 2K (4096 x 2160p) resolution, a 4K - capable display is required
• (Optional) Active DisplayPort to HDMI/DVI/VGA Video Adapter x 1
• (Optional) USB-C to HDMI/DVI/VGA/DisplayPort Video Adapter x 1
USB Peripherals:
• (Optional) Keyboard, Mouse, Flash Drive, Printer, Webcam, Drive Enclosure,
Display Adapter, Mobile Phone, or Tablet, etc. x 2
• (Optional) USB-A to USB-B Cable x 2
• (Optional) USB-C to USB-C Cable x 2
Thunderbolt 3 Peripherals:
• Thunderbolt 3 Enabled Peripheral Devices x 1
• Thunderbolt 3 Cable x 1
SD Card:
• SD, SDHC™ (Secure Digital High Capacity), or SDXC™ (Secure Digital Extended
Capacity) Card x 1
M.2 Drive:
• M-key connector type, 22 x 80 mm (2280) M.2 Drive x 1
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Audio:
• Microphone-Enabled Audio Device x 1
• Speaker-Enabled Audio Device (or Headphones) x 1
• 3.5 mm Audio Cable x 2
Operating Systems:
• Windows® 10, 8, 8.1 or 7.
• macOS 10.14, 10.13 or 10.12.
Installation
Connecting
Front Ports
USB-C (10Gbps) Port
The USB-C (10Gbps) Port on the front panel is not a Thunderbolt 3 port. You can
use this port to connect peripherals using USB 3.0 (10Gbps) technology. This
port supports data throughput only. The port does not support DP Alt Mode or
USB Power Delivery.
Note: This USB-C Port will charge at up to 3A when the Docking Station is
connected to Host Laptop through the Thunderbolt 3 Host Port.
1. Connect a USB-C cable to the USB-C (10Gbps) Port on the front of the
Docking Station.
2. Connect the other end of the USB-C cable to a USB-C port on your
compatible device.
USB-A (5Gbps) Port
The USB-A (5Gbps) Port on the front of the Docking Station can be used to
connect compatible USB devices. These ports can be used to connect media
devices (External Media Drive) or can be used to connect peripheral devices for
use with the connected Host (e.g. Keyboard, Mouse, Web Camera, etc.).
The USB-A (5Gbps) Fast-Charge and Sync Port on the front panel of the Docking
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Station is compliant with USB Battery Charging Specication Revision 1.2 (BC
1.2), which means that you can use the USB-A (5Gbps) Port to connect and
charge a device faster than you can using a traditional standard USB 3.0 port.
1. Connect a USB-A cable into the USB-A Port on the front on the Docking
Station.
2. Connect the other end of the USB-A cable into a USB port on your
compatible device.
SD Card Reader Slot
Installation
1. Gently insert your memory card into the SD Card Reader Slot, with the label
side facing upward.
Note: The card does not need to be forced into place.
2. Your computer system will automatically detect the card and install the
required driver software.
3. To access the content on the SD Card, follow the instructions specic to the
OS that you’re running.
SD Card Removal
Windows
1. On your desktop, click the Safely Remove Hardware icon.
2. In the list that appears, click the SD Card.
3. When a message appears saying that it’s safe to do so, remove the SD
Card from the Docking Station by gently pulling it out of the SD Card
Reader Slot.
Caution! If you remove the SD Card before it’s safe to do so, you could
experience lost or corrupted data on your memory card.
macOS
1. Close any open windows that list the contents of the SD Card.
2. On your desktop, click and drag the USB storage icon to the trash can
6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
icon.
3. Wait ten seconds and then remove the SD Card from the Docking
Station by gently pulling it out of the SD Card Reader Slot.
Caution! If you remove the SD Card before it is safe to do so, you
could experience lost or corrupted data on your memory card.
3.5 mm Microphone Port
1. Connect a 3.5 mm Audio Cable to the 3.5 mm Microphone Port on the
Docking Station.
2. Connect the other end of the 3.5 mm Audio Cable to your Microphone.
3.5 mm Audio Output Port
1. Connect the 3.5 mm Audio Cable from your Speakers, Headphones, etc. to
the 3.5 mm Audio Output Port on the Docking Station.
Rear Ports
USB-A Port
The USB-A port on the rear of the Docking Station can be used to connect
compatible USB devices. These ports can be used to connect media devices
(External Media Drive) or can be used to connect peripheral devices for use with
the connected Host (e.g. Keyboard, Mouse, Web Camera, etc.).
The USB-A (5Gbps) Fast-Charge and Sync Port on the rear panel of the Docking
Station is compliant with USB Battery Charging Specication Revision 1.2 (BC
1.2), which means that you can use the USB-A (5Gbps) Port to connect and
charge a device faster than you can using a traditional standard USB 3.0 port.
1. Connect a USB-A cable to the USB-A port on the rear of the Docking Station.
2. Connect the other end of the USB-A cable to a USB port on your compatible
device.
Ethernet Port
1. Connect a CAT5e/CAT6 cable’s RJ-45 connector to the Ethernet Port on the
rear side of the Docking Station.
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Connect the other RJ45 connector to an RJ45 port on your compatible
Network Device.
Thunderbolt 3 Peripheral Port
The USB-C ports on the rear panel are Thunderbolt 3 ports with a USB-C
connector. The Thunderbolt 3 Peripheral Port can be used to connect a second
display through the Thunderbolt 3 port or a USB-C port. When used as a USB-C
port, you can connect peripherals using USB 3.1 Gen 2 (10Gbps) technology.
This port supports DP Alt Mode and USB Power Delivery with up to 15 Watts of
power.
1. Connect a USB-C Cable or Thunderbolt 3 Cable to the Thunderbolt 3
Peripheral Port on the rear of the Docking Station.
2. Connect the other end of the USB-C or Thunderbolt 3 Cable to a USB port
on your compatible device.
Thunderbolt 3 Host Port
The USB-C ports on the rear panel are Thunderbolt 3 ports with a USB-C
connector. This port will function as the Host Port for connecting to your
Computer. This port supplies up to 85 Watts of power.
Note: This port is recommended for charging as it outputs more power.
1. Connect a USB-C Thunderbolt 3 Cable to the Thunderbolt 3 Host Port on the
rear of the Docking Station.
Note: Ensure you are connecting to the Host Port. This port is indicated by
the small computer icon next to the Thunderbolt 3 icon.
2. Connect the other end of the USB-C Thunderbolt 3 Cable to a Thunderbolt 3
Port on your Computer.
DisplayPort Port
This DisplayPort Port (DisplayPort Revision 1.2) is designed to be used with a
second Display for the Docking Station.
1. Connect a DisplayPort (male to male) cable to the DisplayPort Port on the
rear of the Docking Station.
8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. Connect the other end of the DisplayPort Cable to the DisplayPort port on
your DisplayPort Enabled Display Device.
Power Input Port
See Powering section for more details.
Ports on the Bottom
M.2 SSD Slot
The M.2 SSD Slot will house an NVMe PCIe 3.0 internal Solid State Drive. The
M-key connector type is compatible with a 22 x 80 mm (2280) M.2 Drive.
Note: SSD Drives require careful handling. If you are not careful with your SSD
Drive, lost data may result. Always handle your drive with caution. Be sure that
you are properly grounded or discharge yourself of any static electricity build-
ups by touching a large grounded metal surface for several seconds before
handling your M.2 Drive.
1. Turn the Docking Station upside down.
2. Remove the panel on the bottom of the Docking Station:
• Remove the two screws using a Phillips Head Screwdriver.
• Carefully ip the Docking Station to release the panel.
3. Remove the Holding Screw for the M.2 Drive using a Phillips Head
Screwdriver.
4. Slide your M.2 Drive into the M-key socket at a 45 degree angle.
Note: Ensure your drive is properly seated, with the pins making full
contact, before proceeding to the next step. (gure 1)
9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5. Gently press down on the M.2 drive until the notch on your M.2 Drive is
aligned with the hole for the Holding Screw. Hold the drive in place.
6. Secure your M.2 Drive in place by replacing the Holding Screw that was
removed in step 3, using a Phillips Head Screwdriver. (gure 2)
gure 2
Holding
Screw
gure 1
10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
7. Replace the panel that was removed in step 1 by placing the panel back
onto the Docking Station.
8. Screw in the two screws that were removed in step one, using a Phillips
Head Screwdriver.
Powering
1. Connect the Power Cord to the DC IN 20V Power Input Port.
2. Connect the other end of the Power Cord to the Universal Power Adapter.
3. Connect the Universal Power Adapter to an appropriate power source.
Driver Installation
Install Drivers in Windows 7/8.1/10
When the Docking Station is powered and connected to your laptop, and your
laptop has established a network connection, the required drivers will install
automatically.
You may see a pop-up message requesting permission to allow the Docking
Station to connect to your computer. If a pop-up message appears, do the
following:
1. Click on the pop-up message.
2. Click Always Connect.
3. Click OK.
4. Follow any other on-screen instructions to complete the installation.
(Optional) Install Ethernet drivers
1. Download the latest driver. Use a web browser and navigate to
www.StarTech.com/TB3DK2DPM2.
2. Click the Support tab.
3. Download the Network Card driver.
11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
4. When the download is complete, extract the contents of the compressed
le that you downloaded.
5. Navigate to the location where you extracted the driver contents, and open
the Windows folder.
6. Double-click the Setup.exe le and follow the on-screen instructions to
complete the Ethernet driver installation process.
Display Conguration
Connect HDMI, DVI and VGA Displays
Notes:
• Connect an active adapter to the DisplayPort Port.
• This port does not support Multimode DisplayPort so an active adapter is
required.
• The Docking Station lets you connect two 4K displays.
• The maximum available resolution may be limited if your display is
connected through a video adapter. Check the documentation of the video
adapter to determine its maximum supported resolution.
You can use adapters to connect HDMI, DVI, or VGA displays to the Thunderbolt
3 Peripheral Port and USB Type-C Port:
Connect Multiple Thunderbolt 3 Displays
You can also set up dual displays using multiple Thunderbolt 3 Enabled Displays
in a daisy-chain conguration. For example, you can connect a Thunderbolt
3 Enabled Display to the Thunderbolt 3 Peripheral Port on the Docking
Station. You can then connect another Thunderbolt 3 device, such as a second
Thunderbolt 3 Enabled Display, through the rst Thunderbolt 3 Enabled Display.
Note: A maximum of 2 Displays can be used with each Thunderbolt 3 Port.
12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Congure Displays
Use your Windows operating system to adjust display settings for multiple
monitors. Your laptop hardware must support dual external displays through its
Thunderbolt 3 port.
Supported Video Resolutions
The Docking Station supports the following maximum resolutions:
Number of
Displays Ports Maximum Resolution
1 DisplayPort Port 4096 x 2160p
1Thunderbolt 3
Peripheral Port 4096 x 2160p (60Hz)
2
DisplayPort Port
and Thunderbolt 3
Peripheral Port
4096 x 2160p
• Depending on the conguration and the supported resolutions of your
connected monitor(s), the Docking Station can support video resolutions
lower than specied above.
• Video output capabilities are dependent on the video card and hardware
specications of your connected host laptop.
Video Resolution and Bandwidth Allocation
Thunderbolt technology carries video and data bandwidth, and it prioritizes
video bandwidth to help ensure seamless display performance. The
performance of the remaining dock ports (for example, the USB 3.0 ports)
depends entirely on the display and I/O (input and output) conguration that
you have used.
When multiple high-resolution displays are connected, the Docking Station
13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
needs to allocate additional bandwidth to the displays, and the extra
bandwidth is reallocated from the other I/O ports on the docking station. In this
situation there is less bandwidth available for the remaining ports (for example,
the USB 3.0 ports).
The bandwidth allocation table outlines the approximate download bandwidth
allocation values. The allocation amount depends on the number and the
resolution of your connected displays.
• The bandwidth values are approximate and depend on several variables
including the number, type, resolution, and refresh rate of your connected
display(s).
• When connecting a display to one of the Thunderbolt 3 Ports, a USB-C video
adapter may be required, depending on the input of your display.
Video and I/O
Conguration
DisplayPort
Resolution
Thunderbolt
3 USB-C
Resolution
I/O Bandwidth
Remaining
Data only
(No Displays) N/A N/A Download: 22Gbps
Upload: 22Gbps
DisplayPort
(Single Display
- 4K)
4096 x 2160p
(4K) N/A Download: 22Gbps
Upload: 22Gbps
Thunderbolt 3
USB-C
(Single Display
- 4K)
N/A 4096 x 2160p
(4K - 60Hz)
Download: 22Gbps
Upload: 22Gbps
DisplayPort and
Thunderbolt 3
USB-C
(Two Displays -
Dual-4K )
4096 x 2160p
(4K)
4096 x 2160p
(4K)
Download: 8Gbps
Upload: 22Gbps
14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Operation
LED Indicators
Power:
Solid LED (White)
• Indicates that the Docking Station is active (the Power Cord is correctly
connected to an AC Electrical Outlet).
LED O
• Indicates that the Power Cord is not correctly connected to an AC Electrical
Outlet or the Docking Station is not receiving power.
Charge a Device
If you’re only using the front USB-A (5Gbps) Port to charge a device, a
connection to a Host Laptop isn’t required.
• To charge a device, connect it to the USB-A Port on the front or rear of the
Docking Station.
• The Thunderbolt 3 Peripheral Port will also support battery charging up to
15W.
Note: This front and rear USB-A (5Gbps) Ports can only fast-charge connected
devices that comply with USB Battery Charging Specication Revision 1.2.
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in
this manual and related documents are the property of their respective holders.
Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its
subsidiaries in the U.S. and/or other countries.
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to provide
industry-leading solutions. If you ever need help with your product, visit www.startech.
com/support and access our comprehensive selection of online tools, documentation, and
downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a three-year warranty.
StarTech.com warrants its products against defects in materials and workmanship for the
periods noted, following the initial date of purchase. During this period, the products may
be returned for repair, or replacement with equivalent products at our discretion. The
warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from misuse,
abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
ocers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the actual
price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. If such laws apply, the limitations or exclusions contained in this statement may
not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan. It’s a
promise.
StarTech.com is your one-stop source for every connectivity part you
need. From the latest technology to legacy products — and all the
parts that bridge the old and new — we can help you nd the parts
that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them
wherever they need to go. Just talk to one of our tech advisors or visit
our website. You’ll be connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com
products and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity
and technology parts. StarTech.com was founded in 1985 and has
operations in the United States, Canada, the United Kingdom and
Taiwan servicing a worldwide market.
Reviews
Share your experiences using StarTech.com products, including
product applications and setup, what you love about the products, and
areas for improvement.
Websites
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com