Table of Contents
- Compliance Statements
- Safety Statements
- Product Diagram (VS424HD4K60)
- Front View
- Rear View
- Product Information
- Package Contents
- Requirements
- Installation
- Optional Installation
- Using RS232 to Control the Matrix Switch
- Serial Control Settings
- Using a Network to Control the Matrix Switch
- Installing the IR Receiver
- Lock Button Function
- Locking Input Buttons
- Unlocking Input Buttons
- Downloading Firmware Upgrade
- Hardware Operation
- Unplugging the Universal Power Adapter
- Remote Control
- Remote Control Functionality
- Removing/Replacing the Battery
- Mounting the Matrix Switch
- Installation Requirements:
- Web Interface
- Connecting the Matrix Switch to a Computer
- Accessing the Web Interface
- Switch
- Setting an I/O Position
- Changing Output/Input Name
- Muting/Un-muting a Channel
- Creating an I/O Position Preset
- Loading an I/O Position Preset
- Changing a Preset Name
- EDID Settings
- Configuring EDID Settings
- Downloading EDID Settings
- Downloading EDID Settings from a Connected Sink
- Uploading EDID Settings
- System Settings
- Powering the Matrix Switch On/Off
- Changing Username and Password
- Setting Web Login Timeout
- Changing Network Settings
- Resetting the Matrix Switch to Default Settings
- Upgrading Firmware
- Telnet Control
- Accessing the Command Line in Windows
- Accessing the Command Line in macOS
- Command Line Interface
- Command List
StarTech.com VS424HD4K60 User Manual
Displayed below is the user manual for VS424HD4K60 by StarTech.com which is a product in the Matrix Switchers category. This manual has pages.
Related Manuals
1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでくださ
い。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に
従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements ........................................................................1
Safety Statements ..................................................................................2
Product Diagram (VS424HD4K60) .......................................................7
Front View .................................................................................................................................................... 7
Rear View ...................................................................................................................................................... 7
Product Information ..............................................................................8
Package Contents .....................................................................................................................................8
Requirements ............................................................................................................................................. 8
Installation ..............................................................................................9
Optional Installation ..............................................................................10
Using RS232 to Control the Matrix Switch ....................................................................................... 10
Serial Control Settings ............................................................................................................................. 11
Using a Network to Control the Matrix Switch ............................................................................... 11
Installing the IR Receiver ........................................................................................................................ 11
Lock Button Function ............................................................................12
Locking Input Buttons ............................................................................................................................. 12
Unlocking Input Buttons ........................................................................................................................ 12
Downloading Firmware Upgrade ........................................................12
Hardware Operation ..............................................................................12
Unplugging the Universal Power Adapter .......................................................................................12
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Remote Control ......................................................................................13
Remote Control Functionality .............................................................................................................. 13
Removing/Replacing the Battery ........................................................................................................ 13
Mounting the Matrix Switch ................................................................. 15
Installation Requirements: ..................................................................................................................... 15
Web Interface ..........................................................................................16
Connecting the Matrix Switch to a Computer ................................................................................16
Accessing the Web Interface ................................................................................................................. 16
Switch ....................................................................................................... 18
Setting an I/O Position ............................................................................................................................18
Changing Output/Input Name............................................................................................................. 18
Muting/Un-muting a Channel .............................................................................................................. 19
Creating an I/O Position Preset ............................................................................................................19
Loading an I/O Position Preset ............................................................................................................. 21
Changing a Preset Name ........................................................................................................................ 22
EDID Settings ..........................................................................................24
Conguring EDID Settings .................................................................... 24
Downloading EDID Settings ................................................................. 25
Downloading EDID Settings from a Connected Sink .......................26
Uploading EDID Settings ......................................................................26
System Settings ...................................................................................... 28
Powering the Matrix Switch On/O ................................................................................................... 28
Changing Username and Password ................................................................................................... 29
6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Setting Web Login Timeout ................................................................................................................... 30
Changing Network Settings .................................................................................................................. 31
Resetting the Matrix Switch to Default Settings ............................................................................ 32
Upgrading Firmware ..............................................................................32
Telnet Control .........................................................................................34
Accessing the Command Line in Windows ...................................................................................... 34
Accessing the Command Line in macOS .........................................................................................34
Command Line Interface ........................................................................................................................ 35
Command List ............................................................................................................................................ 35
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Front View
Rear View
IR
Sensor
Lock
Button LED
Indicators
Power
Button
Input
Buttons
HDMI Locking
Screw Holes
HDMI
Output
Ports
(4)
IR IN
RS232
Serial
Port
Control
Port
Service
Port
Power
DC 24V
Port
HDMI
Input
Ports
(4)
HDMI Locking
Screw Holes
8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
• 4 X 4 4K60 Matrix Switch x 1
• Remote Control x 1
• Mounting Brackets x 2
• Universal Power Adapter x 1
• IR Receiver x 1
• User Manual x 1
Requirements
For the latest requirements, please visit www.startech.com/
VS424HD4K60.
Video Source
• HDMI enabled Video Source Devices (e.g. computer, Blu-ray
player) x 4
Display
• HDMI enabled Display Devices (e.g. television, projector) x 4
Cables
• RS232 Serial Cable x 1
• CAT5e/6 Cable x 1
• M/M HDMI cables for Displays Devices and Video Sources
x 4
Replacement Battery
• CR 2025 Battery
9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installation
1. Connect an HDMI Cable (sold separately) to the HDMI Input
Port on the Matrix Switch and to an HDMI Output Port on
the Video Source Device.
Note: If you are using a Locking HDMI Cable, insert and
tighten the HDMI Cable’s Locking Screw into the Lock-
ing Screw Hole above the corresponding HDMI Port on
the Matrix Switch. Using the Phillips Head Screwdriver,
tighten the Locking Screw. Be careful not to over-tighten.
2. Connect an HDMI Cable to the HDMI Output Port on the
Matrix Switch and the other end to an HDMI Input Port on
the Display Device. The corresponding Input LED (front of
Matrix Switch) will light up solid when a Display Device is
connected.
Note: If you are using a Locking HDMI Cable, insert and
tighten the Locking Screw in the Locking Screw Hole
above the corresponding HDMI Port. Using the Phillips
Head Screwdriver, tighten the Locking Screw. Be careful
not to over-tighten.
10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3. Connect the Universal Power Adapter to the Power DC
24V Port, with the arrow on the Universal Power Adapter
Connector Housing facing upward. If aligned properly, the
Universal Power Adapter will lock into the Power DC 24V
Port.
4. Connect the other end of the Universal Power Adapter to
an AC Electrical Outlet.
Optional Installation
Using RS232 to Control the Matrix Switch
To control your Matrix Switch through RS232:
• Connect a 9-Pin Serial Cable (sold separately) to the RS232
Serial Port on the Matrix Switch and to an RS232 Serial
Port on the Host Computer.
11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Serial Control Settings
Setting Description
Baud Rate 115200bps
Data Bit 8 bits
Parity None
Flow Control None
Stop Bit 1
Using a Network to Control the Matrix Switch
To control your Matrix Switch over a network:
• Connect an Ethernet Cable (sold separately) to the Control
Port on the Matrix Switch and to an available LAN Port on a
Network Device.
Note: See the Web Interface section for further control
instructions.
Installing the IR Receiver
Connecting the IR Receiver will extend the IR signal range on
the Matrix Switch.
• Connect the IR Receiver to the IR IN Port on the Matrix
Switch. Face the IR Receiver in the desired direction to
receive the IR signal.
12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Lock Button Function
The Lock Button on the front of the Matrix Switch enables you
to disable or lock the Input Buttons.
Locking Input Buttons
• Press the Lock Button to lock the Input Buttons. The Lock
LED with stay solid and the Input LED will turn o, indicating
that the Input Buttons are locked.
Unlocking Input Buttons
• Press and hold the Lock Button for three seconds. The Lock
LED will turn o and the Input LED will turn on, indicating
that the Input Buttons are unlocked.
Hardware Operation
Unplugging the Universal Power Adapter
• To unplug the Universal Power Adapter gently slide the
Connector Housing away from the Matrix Switch.
Remote Control
Enables you to control the Matrix Switch primary functions
remotely.
13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Remote Control Functionality
Button Functionality
Power • Powers the Matrix Switch On
• Places the Matrix Switch into
Stand-by mode
Output A (1 - 4) • When selected, displays the
corresponding input device (1 - 4)
on Output A
Output B (1 - 4) • When selected, displays the
corresponding input device (1 - 4)
on Output B
Output C (1 - 4) • When selected, displays the
corresponding input device (1 - 4)
on Output C
Output D (1 - 4) • When selected, displays the
corresponding input device (1 - 4)
on Output D
Removing/Replacing the Battery
1. On the back of the Remote Control, slide the Lock on the
Battery Housing.
2. While sliding the Lock, pull the Battery Housing, and slide it
away from the Remote Control.
14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3. Remove the CR 2025 Battery and replace it with a new CR
2025 Battery (sold separately) with the + side facing up.
4. Slide the Battery Housing back into the Remote Control,
the Lock will snap back into place, securing the Battery
Housing to the Remote Control.
Mounting the Matrix Switch
Note: StarTech.com is not responsible for any damages
related to the installation of this product.
Mounting Requirements:
• Server Rack x 1
• Mounting Bracket x 2
• Writing Utensil x 1
• Phillips Head Screwdriver x 1
• M5 Cage Nuts x 4
• M5 Screws x 4
1. Remove the Mounting Screws from the Mounting Holes
on both sides of the Matrix Switch (4).
2. Align the Mounting Brackets with the two Mounting Holes
on both sides of the Matrix Switch.
3. Insert the Bracket Screws (4) through the Mounting
Brackets and into the Mounting Holes.
4. Tighten the Mounting Screws using a Phillips Head
Screwdriver, be careful not to over-tighten.
15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5. Decide where in the server rack you want to install the
Matrix Switch.
6. Insert the M5 Cage Nuts (two per mounting post) into the
square mounting holes on the Server Rack’s Mounting
Posts.
7. Align the Mounting Brackets with the M5 Cage Nuts on
the Server Rack’s Mounting Post.
8. Insert an M5 Screw (two per mounting post) through the
front Mounting Bracket (rail) and into the M5 Cage Nut.
9. Tighten the Mounting Screws using a Phillips Head
Screwdriver, be careful not to over-tighten.
Web Interface
The Matrix Switch’s built-in Web Interface enables you to
control all primary functions:
• Switch
• EDID Settings
• System Settings
• Admin - Logout
Connecting the Matrix Switch to a Computer
Connect the Matrix Switch to a Computer on the same
network.
Accessing the Web Interface
1. Open a Web Browser on the Computer. Make sure that the
Computer is connected to the same network as the Matrix
16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Switch.
2. Enter the Matrix Switch’s default IP address (192.168.1.50)
into the web address bar on the Web Browser.
3. On the Login screen, enter the Username (admin) and
Password (admin)
Login screen
4. Once you have logged into the Web Interface the Switch
tab will appear.
17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Switch
Setting an I/O Position
1. On the Switch tab, click on an Output. The Output will
highlight indicating that it was selected.
Output
2. Click on the Inputs that you want to connect to the selected
Output.
3. Repeat Steps 1 - 2 to congure the other Outputs.
Changing Output/Input Name
1. On the Switch tab, select the Edit icon on the Output
you wish to change.
18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. The Output Name screen will appear.
Output Name screen
3. Enter a new name in the Name eld. The Name eld has an
8-character limitation.
4. Click on the Save button to save the new name.
Muting/Unmuting a Channel
1. On the Switch tab, select the Mute/Blank Button on the
Output Channel you want to mute/blank out.
Note: When the Mute/Blank Button is selected the audio
(Mute) and video (Blank) on the selected Output Channel
with turn O.
2. The icon will appear crossed out, indicating that the
corresponding Output Channel has been muted/blanked
out.
3. Click the Mute/Blank icon a second time to reactivate the
Output Channel.
20
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3. The Preset Set screen will appear.
Preset Set screen
4. Select a Preset Location (e.g. PRESET1) to save the current
preset to.
5. When you have selected a Preset Location, the preset will
be saved and you will return to the Switch tab.
Loading an I/O Position Preset
1. On the Switch tab, click on the Recall the Store I/O Position
icon (top right).
21
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. The Preset Recall screen will appear.
Preset Recall screen
3. Select the I/O position preset you want to load.
4. The Switch tab will appear with the I/O preset loaded.
Changing a Preset Name
1. On the Switch tab click on the Store Current I/O Position
icon (top right).
22
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
2. The Preset Set screen will appear.
Preset Set screen
3. Click on the Edit icon next to a preset, the Edit Preset
Name screen will appear.
4. Enter the new Preset Name (max. 8 characters).
5. Click the Save button to save the new preset name.
- or -
Click on the Cancel button to return to the Switch tab
without making any changes.
23
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
EDID Settings
Conguring EDID Settings
1. On the Switch tab, click on the EDID Settings tab, the EDID
Settings tab will appear.
EDID Settings screen
2. From the Set EDID Mode to drop-down list, select an EDID
setting for each of the Inputs that are connected to the
Matrix Switch.
• FHD2CH: Full High-Denition-2-Channel
• FHDMCH: Full High-Denition-Multi-Channel
• 4KUHD2CH: 4K Ultra High-Denition-2-Channel
• 4KUHDMCH: 4K Ultra High-Denition-Multi-Channel
• 4KUHD+2CH: 4K Ultra High-Denition + 2-Channel
• 4KUHD+MCH: 4K Ultra High-Denition + Multi-Channel
• TXA: Transmitter A
24
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
• TXB: Transmitter B
• TXC: Transmitter C
• TXD: Transmitter D
Downloading EDID Settings
Enables you to save an EDID setting to the Host Computer.
1. On the Switch tab, click on the EDID Settings tab, the EDID
Settings tab will appear.
EDID Settings screen
2. On the EDID Upload/Download section, click the Download
button that corresponds with the EDID Input settings you
want to download (e.g. EDID USER 1 corresponds to Input 1
settings).
3. The EDID Setting will be saved to your Host Computer in a
.bin le format.
25
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Downloading EDID Settings from
a Connected Sink Device
1. On the Switch tab, click on the EDID Settings tab, the EDID
Settings tab will appear.
EDID Settings screen
2. On the EDID Upload/Download section, click the Sink EDID
Download drop-down list and select a sink device.
3. Click the Download button, the EDID Setting will be saved
to your Host Computer in a .bin le format.
Uploading EDID Settings
Enables you to upload a custom EDID setting to the Matrix
Switch.
1. On the Switch tab, click on the EDID Settings tab, the EDID
Settings tab will appear.
26
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
EDID Settings screen
2. On the EDID Upload/Download section, click the Browse
button.
3. The File screen will appear, giving you access to the Host
Computers les. Select the EDID le you would like to
download to the Matrix Switch.
Note: The EDID le must be in .bin le format.
4. Click the Update button, a notication screen will appear
asking “Are you sure you want to update EDID?”.
27
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5. Click the OK button to update the EDID settings.
- or -
Click the Cancel button to return to the EDID Settings tab
without updating.
System Settings
Powering the Matrix Switch On/O
1. From the Switch tab click on the System Settings tab, the
System Settings tab will appear.
System Settings screen
2. Click on the Power eld to toggle the Matrix Switch On or
O.
28
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Changing Username and Password
1. On the Switch tab click on the System Setting tab, the
System Settings tab will appear.
System Settings screen
2. On the Web User Setting section, enter a Username. The
Username eld has an 8 character limitation.
3. Enter the current password in the Old Password eld.
4. Enter the new password in the New Password eld (Max. 8
characters).
5. Re-enter the new password in the Conrm Password eld.
6. Click the Save button to save changes.
29
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Setting Web Login Timeout
Enables you to set the idle time before a user is automatically
logged out of the Web Interface.
1. On the Switch tab click on the System Setting tab, the
System Settings tab will appear.
System Settings screen
2. Click the Web Login Timeout (Minute) drop-down list
and select a new timeout time (values range from 5 - 60
minutes).
30
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Changing Network Settings
Enables you to change/set the Matrix Switch’s IP mode, IP
address, netmask, gateway, and MAC address.
1. On the Switch tab click on the System Setting tab, the
System Settings tab will appear.
System Settings screen
2. Enter the following network information:
• IP Mode
• Static
• DHCP
• IP address
• Netmask
• Gateway
• MAC Address
31
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
3. Click the Save button to save the network settings.
Resetting the Matrix Switch to Default Settings
1. On the Switch tab click on the System Settings tab, the
System Settings tab will appear.
System Settings screen
2. On the Reset to Defaults section, click on the Routing Reset
button to reset all routing settings.
- or -
Click on the Factory Reset button to reset the Matrix
Switch to factory defaults.
Upgrading Firmware
Note: Do not turn o the Matrix Switch when performing a
rmware update.
Enables you to upgrade the Matrix Switch’s rmware.
32
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
For future Firmware updates refer to the Firmware section on
the Product Support tab www.startech.com/VS424HD4K60.
Note: Connect the Mini USB to USB-A Adapter to the
Service Port, in order to connect a USB-A Device.
1. Connect a Mini USB Cable to the Service Port on the
Matrix Switch and connect the other end to a USB Port on
the Host Computer.
2. From the Switch tab click on the System Settings tab, the
System Settings tab will appear.
System Settings screen
3. On the Firmware Upgrade section, click on the Browse
button.
4. The File screen will appear which enables you to access the
Host Computers les. Select the appropriate rmware le.
5. Click the Upgrade button to apply the rmware upgrade.
33
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Note: While the rmware is upgrading do not turn o the
Matrix Switch.
Telnet Control
Telnet control enables you to use a computer command line to
control Matrix Switch functionality.
Accessing the Command Line in Windows
1. From the Start menu type cmd in the Search eld
2. Press Enter.
Accessing the Command Line in macOS
• From the Go menu, select Application - Utilities - Terminal.
Command Line Interface
To access the Matrix Switch’s command line:
1. On the Host Computer’s command line type Telnet,
followed by the IP Address of the Matrix Switch and a
port number if you are not using a standard or default port
number.
Command Line Interface screen
2. Press the Enter button, to connect to the Matrix Switch.
34
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Command List
The following is a list of commands that you can use through a
computer’s command line to control Matrix Switch functions:
Notes: All commands must be followed by pressing the
Enter button in order to execute the command.
Commands are not case-sensitive.
Commands also work with RS232 (serial).
Command Description
A N Switch Output A to Input N (N = 1 - 4)
B N Switch Output B to Input N (N = 1 - 4)
C N Switch Output C to Input N (N = 1 - 4)
D N Switch Output D to Input N (N = 1 - 4)
I N Switch all Outputs to Input N (N = 1 - 4)
AB....N Switch outputs AB to Input N (N = 1 - 4)
SETIP xxxx.
xxxx.xxxx Setting IP, Subnet, Gateway, for a Static IP (x
= 0 - 255)
IPCONFIG Displays the current IP Conguration
RSTIP Sets the IP conguration to DHCP mode
P0 Powers the Switch O
P1 Powers the Switch On
35
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
STORE N Stores the current input/output to setting N
(N = 1 - 4)
SHOW N Shows the current port’s input/output
setting N (N = 1 - 4)
PRESET N Creates a preset input/output setting using
N (N = 1 - 4)
NAME N
N1 Names port N as N1 (N = 1 - 4)
N1 =
(LENGTH =
8 MAX)
ST Displays the Switch’s current rmware
version
EM N N1 Sets port N’s EDID mode to N1
EM N Displays port N’s current EDID mode
RS Resets routing settings back to default
USBISP Enables you to update the Switch’s
rmware using the USB port
HELP Displays all commands and descriptions
?Displays all commands
QUIT Exits Telnet
36
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or
their ocers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of
prots, loss of business, or any pecuniary loss, arising out of or related to the use
of the product that exceeds the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
36
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle
15 Gowerton Rd.,
Brackmills
Northampton
NN4 7BW
United Kingdom
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support