Thomson 43UG6400 User Manual
Displayed below is the user manual for 43UG6400 by Thomson which is a product in the TVs category. This manual has pages.
Related Manuals
EN 1
English
Important information
Safety
Ensure that your domestic mains supply voltage
matches the voltage indicated on the identication
sticker located at the back of your set. Where the
mains plug, AC inlet or an appliance coupler is used
as disconnect device, it shall remain readily operable.
On certain models, the light indicator is located at the
side of the TV set. The absence of a light indication
at the front does not mean that the TV set is fully
disconnected from the mains. To disconnect the TV
set completely, the mains plug must be pulled out.
The TV set’s components are sensitive to heat. The
maximum ambient temperature should not exceed
35º Celsius. Do not cover the vents at the back or
sides of the TV set. Leave sucient space around it to
allow adequate ventilation. Install the appliance away
from any source of heat (replace, etc.) or appliances
creating strong magnetic or electric elds.
Moisture in rooms where the set is installed should
not exceed 75% humidity. Moving the set from a cold
place to a warm one can cause condensation on the
screen (and on some components inside the TV set).
Let the condensation evaporate before switching the
TV set on again.
The or POWER/ button on the TV set or the
button on the remote control can be used to switch it
on and put it into standby mode. If you are not going
to be watching the TV for a lengthy period of time,
switch it o completely by removing the plug from the
mains power socket.
During thunderstorms, we recommend that you
disconnect the TV set from the mains and aerial so
that it is not aected by electrical or electromagnetic
surges that could damage it. For this reason, keep the
mains and aerial sockets accessible so they can be
disconnected, if necessary.
Unplug the TV set immediately if you notice it giving
o a smell of burning or smoke. You must never,
under any circumstances, open the TV set yourself,
as you run the risk of an electric shock in doing so.
WARNINGS
This appliance is intended for domestic household
use only and should not be used for any other
application, such as for non-domestic use or in a
commercial environment.
If the external exible cable or cord of this product is
damaged, it shall be replaced by the manufacturer or
his service agent or a similar qualied person in order
to avoid a hazard.
Leave more than 10cm clearance around the
television to allow adequate ventilation. The
ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
The apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids, such as
vases shall be placed on the apparatus.
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, re
or the like.
To reduce the risk of re or electric shock, do not
expose this apparatus to rain or moisture.
Never place a television set in an unstable location. A
television set may fall, causing serious personal injury
or death. Many injuries, particularly to children, can
be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the
manufacturer of the television set.
• Only using furniture that can safely support the
television set.
• Ensuring the television set is not overhanging the
edge of the supporting furniture.
• Not placing the television set on tall furniture
(for example, cupboards or bookcases) without
anchoring both the furniture and the television set to
a suitable support.
• Not placing the television set on cloth or other
materials that may be located between the television
set and supporting furniture.
• Educating children about the dangers of climbing on
furniture to reach the television set or its controls.
If your existing television set is being retained and
relocated, the same considerations as above should
be applied.
Equipment with this symbol is a Class II or
double insulated electrical appliance. It has
been designed in such a way that it does
not require a safety connection to electrical
earth.
Equipment without this symbol is a Class I
electrical appliance. It shall be connected
to a mains socket outlet with a protective
earthing connection.
To prevent the spread of re, keep candles
or other open ames away from this product
at all times.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
N
This symbol indicates that the fuse may
be in the neutral, and that the mains shall
be disconnected to de-energize the phase
conductors.
To prevent injury, this apparatus must be securely
EN 2
English
attached to the oor/wall in accordance with the
installation instructions.
To reduce the risk of RF exposure, the use distance
of this apparatus should be at least 100cm.
If an outside antenna or cable system is connected to
the product, be sure the antenna or cable system is
grounded by a skilled person so as to provide some
protection against voltage surges and built-up static
charges.
TV screen
The TV screen used in this product is made of glass.
Therefore, it can break when the product is dropped
or impacted upon by other objects.
The TV screen is a very high technology product,
giving you nely detailed pictures. Occasionally, a few
nonactive pixels may appear on the screen as a xed
point of blue, green or red. This does not aect the
performance of your product.
Care
Use a glass-cleaning product to clean the screen and
a soft cloth and mild detergent to clean the rest of the
set.
Important: Using strong detergents, alcohol-based
and abrasive products may damage the screen.
Dust the vents at the back and sides regularly. Using
solvents, abrasive or alcohol-based products could
damage the TV set. If an object or liquid enters the
appliance, unplug it immediately and have it checked
by an authorized engineer. Never open the appliance
yourself since this may put you at risk or damage the
appliance.
ESD regulation
This apparatus meets ESD performance criteria.
In case the apparatus does not recover in Ethernet
connection mode or USB playing mode due to
electrostatic discharge, user intervention is required.
Bluetooth function notice
Bluetooth® technology (if available in your TV)
uses 2.4GHz frequency thus close proximity to Wi-
Fi access points, routers or microwave ovens might
interfere with Bluetooth audio streaming. If you face
interruptions in audio reception, you should restart
your Bluetooth device to nd frequency with less
interferences and if you continue to face issues you
should move closer to TV or increase space between
TV and source of interferences.
Bluetooth declaration ID: D043137
Hanging the TV set on the wall
Warning: This operation requires two people.
To ensure a safe installation, observe the following
Important information
safety notes:
• Check that the wall can support the weight of the TV
set and wall mount assembly.
• Follow the mounting instructions provided with the
wall mount. For certain models, make sure to screw
the hexagonal VESA wall mounting screw bosses
(and screws) provided with the set into the nuts for
the wall mount at the back of your set before your
wall mounting.
• The TV set must be installed on a vertical wall.
• Make sure to use only screws suitable for the
material of the wall.
• Make sure that the TV set cables are placed so that
there is no danger of tripping over them.
All other safety instructions about our TV sets are also
applicable here.
Multi product user manual
The features described in this manual are common to
most models. Some features may not be available on
your TV and/or your TV may include features that are
not described in this user manual. The illustrations in
this manual may dier from the actual product. Please
refer to the actual product.
EN 3
English
Dear Customer,
Hereby, TCL declares that this device is in compliance with Directive 2014/53/EU. The full text of the EU declaration
of conformity is available at the following internet address: www.mythomson.com
The EU declaration of conformity can be downloaded directly at www.mythomson.com/eu/doc/XXXXXXXX *
* Please replace «XXXXXXXX» by the exact model name.
Figures and illustrations in this User Manual are provided for reference only and may dier from actual product
appearance. Product design and specications may be changed without notice.
Important information
Information for Users on Disposal of Old Equipment and Batteries
[European Union]
These symbols indicate that the electrical and electronic equipment and the battery with this
symbol should not be disposed of as general household waste at their end-of-life. Instead, the
products should be handed over to the applicable collection points for the recycling of electrical
and electronic equipment as well as batteries for proper treatment, recovery and recycling in
accordance with your national legislation and the Directive 2012/19/EU, 2006/66/EC and 2008/12/
EC.
By disposing of these products correctly, you will help to conserve natural resources and will help
to prevent potential negative eects on the environment and human health which could otherwise
be caused by inappropriate waste handling of these products.
For more information about collection points and recycling of these products, please contact your
local municipal oce, your household waste disposal service or the shop where you purchased
the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
[Business users]
If you wish to dispose of this product, please contact your supplier and check the terms and
conditions of the purchase contract.
[Other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to dispose of these items, please
do so in accordance with applicable national legislation or other rules in your country for the
treatment of old electrical equipment and batteries.
Notice:
The sign Pb
below the
symbol for
batteries
indicates that
this battery
contains lead.
Products
Battery
EN 4
English
Important information ………………………………… 1
Chapter 1 - Connections
Connect the power and antenna …………………… 5
Connect Blu-ray Disc player, HD game console, HD
camcorder, headphones, CI module ………………… 5
Connect to the Internet ……………………………… 6
Chapter 2 - Getting started
Remote control functions …………………………… 7
Installing batteries …………………………………… 7
Switch the TV on and o ……………………………… 8
Initial setup …………………………………………… 8
Chapter 3 - Basic TV operations
Accessing channels …………………………………… 9
Watching connected devices ………………………… 9
Adjusting volume ……………………………………… 9
Accessing Android TV homepage …………………… 9
Using TV settings menu ……………………………… 9
Chapter 4 - Using more of your TV
Installing channels ………………………………… 10
Common interface ………………………………… 10
Using the common interface module …………… 10
Accessing common interface services ………… 10
Using subtitles ……………………………………… 10
Turning on/o subtitles …………………………… 10
Enabling subtitle languages on digital TV
channels …………………………………………… 10
Selecting a subtitle type on digital TV channels 10
Using Teletext ……………………………………… 11
Selecting decoding page language …………… 11
Digital Teletext language ………………………… 11
T-Link ………………………………………………… 11
Enabling or disabling T-Link …………………… 11
Using Auto power on ……………………………… 11
Using Auto standby ……………………………… 11
HbbTV ……………………………………………… 11
HbbTV access …………………………………… 11
HbbTV deactivation ……………………………… 11
Using EPG (Electronic Programme Guide) ……… 12
Bluetooth function…………………………………… 12
Quick start function ………………………………… 12
Networked waking up ……………………………… 12
Reset to factory default settings…………………… 12
Chapter 5 - Other information
Password in Parental Control ……………………… 13
Troubleshooting …………………………………… 13
Contents
EN 5
English
Connect the power and antenna
To switch on TV after connecting power cord, press or POWER/ .
Notes:
- Position of power socket varies according to TV model.
- Disconnect the power cord before connecting devices.
Cable
Chapter 1 - Connections
(Optical)
Digital
audio out
USB 2.0
(Service port)
5V 0.5A
MAX
LAN HDMI 1 (4K) HDMI 2 (4K)
ARC
Antenna/Cable input Satellite input
13/18V 0.4A
MAX
HDMI 3 (4K) USB 2.0
5V 0.5A
MAX
Common interface
AV adapter
HD game
console
Blu-ray Disc
player HD Camcorder
Connect Blu-ray Disc player, HD game console, HD camcorder, headphones,
CI module
EN 6
English
Connections
Notes:
-Your TV might not have all connectors visible on diagram above. Number of USB and HDMI ports may vary
according to TV model.
-Button and connector locations may vary according to TV model.
-USB connectors are for data input from USB drives and for connecting other relevant USB devices where
applicable.
-All USB devices have to be directly connected to TV set without cable extenders. In case extender is
required, maximum 50cm length is recommended. Longer extenders should have ferrite beads.
-ARC (Audio Return Channel) function is only supported on the HDMI port identied with ARC. To use ARC
function, please turn on T-Link function rst as described in the T-Link section.
-It is recommended to use high quality and well shielded HDMI cables to avoid possible interferences.
-Please use headphones with 3.5mm TRS connector. Excessive sound pressure from headphones can cause
hearing loss.
Connect to the Internet
Wired connection
Wireless connection
Router
Modem Internet
LAN port
Modem Internet
Wireless router
Note: The following instructions are just the usual ways to connect your TV to the wired or wireless network.
The connection method may be dierent depending on your actual network conguration. If you have any
questions about your home network, please refer to your Internet service provider.
Network settings:
1. Press on the remote control to display the Android TV homepage.
2. Press ▲/▼/◄/► to move the cursor to on the right top of the screen and press OK to enter the Settings
menu.
3. Press ▲/▼ to select Network & Internet, press OK to enter the submenu and follow the on-screen
guidance to set up your network.
EN 7
English
Remote control functions
Most of your television's functions are available via the menus that appear on the screen. The remote control
supplied with your set can be used to navigate through the menus and to congure all the general settings.
Chapter 2 - Getting started
To switch the sound o and back on.
Standby / quit standby.
Numeric buttons To enter channel numbers or a digit.
To access T-Channel.
LIST To display the channel list.
/To control the volume.
To display programme information, if available.
To display the TV settings menu.
P / To change channels.
To access the Android TV homepage.
To display the Option menu.
▲/▼/◄/►Navigation direction buttons.
OK To conrm an entry or selection.
To return to the previous menu or quit an App.
To select input source.
EXIT To exit the on-screen menu.
LANG To select an audio language available for selected digital TV
programme.
GUIDE To toggle the Electronic Programme Guide on or o (only
available for digital channels).
TEXT To toggle Teletext on or o.
SUBT. To select a subtitle language available for selected digital TV
programme.
Colour buttons To select tasks or Teletext pages; to be used for HbbTV
function.
To start fast reverse.
To pause playback.
To start fast forward.
ZOOM To select the screen mode.
Note: You are recommended to use the full screen mode.
Do not use the display mode with black bars on both sides
of the picture (such as 4:3) for a long time; otherwise the TV
screen may be damaged permanently.
To start playback.
To stop playback.
NETFLIX To access Netix if available.
Note: The remote control type may be changed without notice.
Installing batteries
1. Push to open the back cover as
illustrated.
2. Insert two AAA batteries according to the
polarities marked on the batteries case.
3. Replace the back cover as illustrated.
EN 8
English
Getting started
Important:
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Remove batteries when
the remote control is not to be used for a long time. Batteries left in equipment may cause damage through
deterioration and corrosive leakage, invalidating the guarantee.
To protect the environment use local recycling facilities for battery disposal. Dispose of used batteries
according to the instructions.
CAUTION: Risk of explosion if batteries are replaced by an incorrect type. Replace only with the same or
equivalent type recommended by the equipment manufacturer.
If the batteries in your remote control are run down, you can use the button on your TV set.
You can turn on the TV from standby mode by pressing the button on your TV set.
While the TV is on, the multi-function menu appears by pressing the button on your TV set. For more
information about how to use the multi-function menu, please refer to the figure below.
• Press the button to move the highlight to the next function selection.
• Press and hold the button for more than 2 seconds to confirm your selection.
Note: Please refer to the Quick Start Guide to nd the button on your TV set.
Switch the TV on and o
1. When the power cord is connected, the TV will be turned on directly or be in standby mode. If the TV is in
standby mode, press the or POWER/ button on the set or the button on the remote control to turn it
on.
2. To put the TV into standby mode, press the button on the remote control. The TV set remains powered up,
but with low energy consumption.
3. To switch the TV o, unplug the mains plug from the mains outlet.
Initial setup
The rst time you switch the set on, the Welcome screen appears, which guides you through the initial setup
process. Follow the on-screen instructions to nish the initial setup process such as selecting the language,
connecting to the network, scanning channels, and more. During each step, either make a choice or skip the
step. If you skip a step, you can perform the setup later from the settings menu.
Note: If the channel search retrieved only the analogue channels it could be caused by poor broadcasting and
therefore is not covered by manufacturer warranty. Manufacturers cannot be held responsible for lack of
or poor broadcasting in some areas.
EN 9
English
Chapter 3 - Basic TV operations
Accessing channels
Using the numeric buttons: press the corresponding
numeric buttons on the remote control to access the
channels.
Using the P / buttons: press the P / buttons
on the remote control to scroll through the channels.
Using the LIST button: press the LIST button on the
remote control to display the channel list and press
▲/▼/◄/► and OK to select channels.
Watching connected devices
Press on the remote control to display the source
list. Press ▲/▼ to select TV or other input sources
and press OK to conrm.
Adjusting volume
Volume control: press the / buttons on the
remote control to increase or decrease the volume.
Sound mute: press the button to temporarily mute
the sound. Press this button again or the button
to restore the sound.
Accessing Android TV homepage
Allows you to enjoy Internet Applications (Apps) and
specially adapted Internet websites, and perform
system settings for your TV. You can make controlling
with the TV remote control.
WARNING:
• Congure the network settings before using Smart
TV applications.
• Slow responses and/or interruptions may occur,
depending on your network conditions.
• If you experience a problem using an application,
please contact the content provider.
• According to circumstances of the content provider,
an application’s updates or the application itself may
be discontinued.
• Depending on your country's regulations, some
applications may have limited service or not be
supported.
• Changes in application content may be made
without prior notice by the service provider.
1. Press on the remote control to display the
Android TV homepage.
2. Press ▲/▼/◄/► and OK to enter the desired
Apps, functions or settings.
3. Press to return to the homepage.
Note: Since the connection with Internet takes
time, it’s recommended that you wait a few
minutes to use the Smart TV feature after
activation of TV from standby.
Using TV settings menu
Allows you to adjust TV settings, such as picture and
sound.
1. Press on the remote control to display the TV
settings menu.
2. Press ▲/▼ to select the desired item, then press
OK/► to enter the corresponding submenu.
3. In submenus, press ▲/▼ to select menu options,
then press OK/► to enter the option list, the
adjustment interface, or the corresponding
submenu.
4. Press to return to the previous menu.
5. Press EXIT or to close the menu.
Notes:
-You can also press on the remote control,
select TV settings (if available) and press OK to
enter the TV settings menu. Some options may
not be available for certain signal sources.
-Setting LED motion clear on will make fast
moving images clearer by controlling the LED
backlight, but the picture will be darker and more
ickering than with LED motion clear o.
EN 10
English
Chapter 4 - Using more of your TV
Installing channels
This section describes how to search and store
channels automatically. This may be done in any of
the cases below:
- you have skipped the channel installation step in the
initial setup;
- you are prompted that there are no channels in TV
mode;
- you want to update your channels.
1. In TV mode, press on the remote control and
select Channel > Channel scan. Press OK/► to
enter.
2. The TV installs and arranges channels according
to your country or region. Press ▲/▼ to select
Country/Region, and press OK/► to enter. Enter
the default password 1234 or your own password
in case you have changed the password in the
System > Lock menu. Press ▲/▼ to select your
country or region and press OK to conrm.
3. Press ▲/▼ to select Automatic search and press
OK/► to enter.
4. Press ▲/▼ to select Tuner mode and press
◄/► to select Cable, Antenna or Satellite.
(Note: Satellite option is available only in selected
models.)
5. Press ▲/▼ to select other options to congure.
6. After conguration is completed, press ▼ to select
Search and press OK to start scanning channels.
7. The channel search may take a few minutes. After
the automatic search, channels are arranged in a
preset order. If you want to edit the channel list,
press on the remote control, select Channel >
Channel organizer and press OK/► to enter.
Common interface
Encrypted digital TV channels can be decoded with a
common interface module and a card provided by a
digital TV service operator.
The common interface module may enable several
digital services, depending on the operator and
services you choose (for example, pay TV). Contact
your digital TV service operator for more information
about services and terms.
Using the common interface module
WARNING: Switch o your TV before inserting a
common interface module. Be sure to follow the
instructions described below. Wrong insertion of
a common interface module may damage both the
module and your TV.
1. Following the directions printed on the common
interface module, gently insert the module into the
common interface slot on the TV.
2. Push the module in as far as it will go.
3. Turn on the TV and wait for the common interface
function to be activated. This may take several
minutes.
Note: Do not remove the common interface
module from the slot. Removing the module
will deactivate the digital services.
Accessing common interface services
After inserting and activating the common interface
module, press on the remote control, select
Channel > Common interface and press OK/► to
enter.
This menu option is only available if the common
interface module is correctly inserted and activated.
On-screen applications and content are provided by
your digital TV service operator.
Using subtitles
You can enable subtitles for each TV channel.
Subtitles are broadcast via Teletext or DVB-T/DVB-C/
DVB-S digital broadcasts. With digital broadcasts,
you have the additional option of selecting a preferred
subtitle language.
Turning on/o subtitles
1. Press on the remote control, select Channel >
Subtitle and press OK/► to enter.
2. Select the Subtitle option, and press OK to toggle
between on or o.
3. Press EXIT or to close the menu.
Enabling subtitle languages on digital TV
channels
1. Press on the remote control, select Channel >
Subtitle > Digital subtitle language 1st and
press OK/► to enter.
2. Press ▲/▼ to select a subtitle language as your
preferred language and press OK to conrm.
3. Press ▲/▼ to select Digital subtitle language
2nd and press OK/► to enter.
4. Press ▲/▼ to select a secondary subtitle language
and press OK to conrm.
5. Press EXIT or to close the menu.
Shortcut operation: Press SUBT. on the remote
control to directly select a subtitle language available
for the selected digital TV programme.
Selecting a subtitle type on digital TV
channels
1. Press on the remote control, select Channel >
Subtitle > Subtitle type and press OK/► to enter.
2. Press ▲/▼ to select a subtitle type and press OK
to conrm. You can select Hearing impaired to
EN 11
English
Using more of your TV
display the hearing impaired subtitles with your
selected language.
3. Press EXIT or to close the menu.
Using Teletext
Selecting decoding page language
1. Press on the remote control, select Channel >
Teletext > Decoding page language and press
OK/► to enter.
2. Press ▲/▼ to select a proper type of language
in which Teletext will display and press OK to
conrm.
3. Press EXIT or to close the menu.
Digital Teletext language
On digital TV channels, depending on the
broadcaster, you may be able to enjoy a service with
multiple initial Teletext pages in dierent languages.
This function allows you to select an available
language as primary language, which relates to
dierent initial Teletext pages.
1. Press on the remote control, select Channel >
Teletext > Digital teletext language and press
OK/► to enter.
2. Press ▲/▼ to select a language and press OK to
conrm.
3. Press EXIT or to close the menu.
T-Link
Use this function to search for CEC devices connected
to the HDMI sockets in your TV and enable one-touch
play and one-touch standby between CEC devices.
Enabling or disabling T-Link
1. Press on the remote control, select System >
T-Link and press OK/► to enter.
2. Select the T-Link option, and press OK to toggle
between on or o.
3. Press EXIT or to close the menu.
Using Auto power on
Enables the TV to automatically power on when you
power on a CEC device (e.g. DVD) with the device’s
remote. Press OK to turn it on to enable this function.
Using Auto standby
Enables all CEC devices to automatically go to the
standby mode when you turn o the TV with the TV
remote. Press OK to turn it on to enable this function.
Note: The CEC functions depend on the devices
connected and it is possible that some
devices may not interoperate correctly when
connected to this TV. The user manual or
the manufacturer of the problematic devices
should be consulted for further information.
HbbTV
HbbTV (Hybrid broadcast broadband TV) is a service
oered by certain broadcasters and available only on
some digital TV channels. HbbTV delivers interactive
television over broadband Internet. These interactive
features are added to and enrich the normal digital
programmes, and include services such as digital
teletext, electronic programme guide, games, voting,
specic information related to the current programme,
interactive advertising, information magazines, catch-
up TV, etc.
To use HbbTV please ensure your TV is connected to
Internet and HbbTV is switched on.
Notes:
-HbbTV services are broadcast- or country-
dependent and may be unavailable in your area.
-You cannot download les to your TV with
HbbTV function.
-Application provider or broadcasting related
conditions may cause an HbbTV application to
be unavailable momentarily.
-To access HbbTV applications you must connect
your TV to the Internet via a broadband link.
HbbTV applications may not work correctly in
case of network related issues.
HbbTV access
1. Press on the remote control, select System >
HbbTV settings and press OK/► to enter.
2. Select the HbbTV option, and press OK to turn it
on.
3. When you tune to a digital TV channel that oers
HbbTV, this will be signalled to you by an on-
screen indication (generally a red button, but
other colour buttons may also be used). Press
the indicated colour button to open the interactive
pages.
4. Use ▲/▼/◄/► and the colour buttons to navigate
through the HbbTV pages and press OK to
conrm.
HbbTV deactivation
To avoid disturbances that may be caused by HbbTV
broadcasting tests, you can turn o the HbbTV
function:
1. Press on the remote control, select System >
HbbTV settings and press OK/► to enter.
2. Select the HbbTV option, and press OK to turn it
o to disable it.
EN 12
English
Using more of your TV
Using EPG (Electronic Programme
Guide)
EPG is an on-screen guide that displays scheduled
digital TV programmes. You can navigate, select and
view programmes.
1. Press GUIDE on the remote control, the
Programme Guide menu will appear, which
allows you to get information about the current
or next programme playing on each channel.
Navigate through the dierent programmes using
the ▲/▼/◄/► buttons on the remote control.
2. Use the related buttons shown at the bottom of the
screen to view EPG.
-Watch now or More: Press OK to watch the
selected channel or view more information about
the selected programme.
-Programme lter: Press to display programme
lter for digital TV programmes.
-Custom schedule: Press the red button to set a
schedule.
-Select date: Press the green button to select
date.
-Schedule list: Press the yellow button to view
your schedule list.
3. Press GUIDE or EXIT to exit EPG.
Bluetooth function
(* not available for some models)
Bluetooth® is a wireless technology standard for
exchanging data over short distance between
Bluetooth devices. You can connect Bluetooth audio
device, mouse or keyboard via the TV.
1. Press on the remote control, press ▲/▼/◄/►
to move the cursor to on the right top of the
screen and press OK to enter.
2. Select Remotes & Accessories > Add accessory
and press OK to enter. The TV will search nearby
Bluetooth devices automatically. Select an
available device, press OK and follow the guides
on the screen to connect it.
Note: Bluetooth technology (if available in your TV)
uses 2.4GHz frequency thus close proximity
to Wi-Fi access points, routers or microwave
ovens might interfere with Bluetooth audio
streaming. If you face interruptions in
audio reception, you should restart your
Bluetooth device to nd frequency with less
interferences and if you continue to face
issues you should move closer to TV or
increase space between TV and source of
interferences.
The Bluetooth word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by TCL is under license. Other
trademarks and trade names are those of their
respective owners.
Quick start function
It enables you to turn on your TV faster from standby
mode than turning this function o, but it will also
increase standby power consumption.
1. Press on the remote control, select
> Device
Preferences > Quick Start > Enable Quick Start
and press OK to toggle between on and o.
2. Press to return to the previous menu.
Networked waking up
This function allows you to turn on your TV from
standby mode via a network. To use this function,
please make sure:
1. Your TV is connected to an eective wireless home
network;
2. The desired controller, such as a smartphone, is
connected to the same wireless network as your
TV;
3. An App which supports networked waking up
function, such as Youtube, has been installed into
the controller;
4. Networked standby is turned on in the Network
& Internet menu from the homepage.
When the TV is in networked standby mode, you can
use the App to wake up the TV remotely.
Notes:
-This feature is disabled if you press and hold the
button on the remote control and conrm to
shut the TV down.
-Before using the feature of networked waking up,
make sure the Quick Start function is enabled.
-This function may not be available for certain
models.
Reset to factory default settings
Allows you to reset the TV to factory default settings.
1. Press on the remote control, select > Device
Preferences > Reset > Factory data reset >
Erase everything and press OK to conrm.
2. Use the numeric buttons on the remote control to
enter the password 1234 or your own password in
case you have changed it.
3. Select OK and press OK to conrm.
4. The Welcome screen appears. Follow the
instructions in the section Initial setup.
EN 13
English
Chapter 5 - Other information
Password in Parental Control
- The default password is 1234. You can change it to
a new one.
- The super password is 0423. If you forget your
code, enter the super password to override any
existing codes.
Troubleshooting
Please check the following list before requesting
service.
There is no picture or sound.
• Make sure the power cord is properly inserted in the
power outlet.
• Make sure the source type is set correctly.
• Make sure the antenna is properly connected.
• Make sure the volume is not set to minimum or the
sound is not set to mute.
• Make sure the headphones are not connected.
• The TV may be receiving a signal other than from
TV broadcasting stations.
Picture is not clear.
• Make sure the antenna cable is properly connected.
• Consider whether your TV signal is being properly
received.
• Poor picture quality can occur due to a VHS
camera, camcorder, or other peripheral being
connected at the same time. Switch o one of the
other peripherals.
• The ‘ghost’ or double image may be caused by
obstruction to the antenna due to high-rise buildings
or hills. Using a highly directional antenna may
improve the picture quality.
• The horizontal dotted lines shown on the pictures
may be caused by electrical interference, e.g., hair
dryer, nearby neon lights, etc. Turn o or remove
these.
Picture is too dark, too light or tinted.
• Check the colour adjustment.
• Check the brightness setting.
• Check the sharpness function.
Remote control does not work.
• Check the batteries of the remote control.
• Make sure the remote sensor window on the TV
front is not under strong uorescent lighting.
• Try to clean the remote sensor window on the TV
front with a soft cloth.
If the above suggestions do not solve your technical
issue, please refer to the warranty card for service
information.
Operating Conditions
Temperature 5°C - 35°C (41°F - 95°F)
Humidity 20 - 75% (non-condensing)
Storage Conditions
Temperature -15°C - 45°C (5°F - 113°F)
Humidity 10 - 90% (non-condensing)
Radio Information
• Bluetooth® transmitter frequency range:
2402 - 2480MHz
• Bluetooth® transmitter power:
5dBm (+/-5dB)
• 2.4G Wi-Fi transmitter frequency range:
2412 - 2472MHz
• 2.4G Wi-Fi transmitter power:
16dBm (+3dB / -5dB)
• DVB-T/T2/C tuner frequency range:
50.5 - 858MHz
• DVB-S/S2 tuner frequency range:
950 - 2150MHz
OSS Notice
This product uses the GPL (Version 2 and 3) and
LGPL (version 2.1) and MPL (version 1.1).
To send inquiries and requests for questions
regarding open source, contact nearest TCL oce.
This product uses some software programs which are
distributed under the Independent JPEG Group.
This product uses some software programs which are
distributed under the libpng Project.
This product uses some software programs which are
distributed under the Freetype Project.
This product uses some software programs which are
distributed under the zlib Project.
This product uses some software programs (libxml2,
curl, expat, c-areas) which are distributed under the
MIT.
This product uses CyberLink for C which is distributed
under the Open Source Project.
This product uses opensl, xerces which is distributed
under the Apach License Project.
GPL software: Linux Kernel, glib, libiconv, gcc libgcc,
gcc libstdc++, u-Boot loader, mepg, util-linux-ng,
e2fsprogs, wget, iptables
LGPL software: DFB (DirectFB), gstreamer, gst-
plugins-base, gst-plugins-good, gst-plugins-bad, gst-
plugins-ugly, gst-mpeg, glibc, wpa_supplicant
BSD software: webp, mng, uriparser
GNU software: dosfstools
EN 14
English
Other information
[Legal Statement] of TCL - manufacturer of this
TV set
Due to the various capabilities of products featuring
the SmartTV - Services, as well as limitations in the
available content, certain features, applications, and
services may not be available on all devices or in
all territories. Some features on SmartTV may also
require additional peripheral devices or membership
fees that are sold separately. Please visit our website
for more information on specic device information
and content availability. The services and availability
of content through SmartTV are subject to change
from time to time without prior notice.
All content and services accessible through this
device belong to third parties and are protected by
copyright, patent, trademark and/or other intellectual
property laws. Such content and services are
provided solely for your personal noncommercial use.
You may not use any content or services in a manner
that has not been authorized by the content owner
or service provider. Without limiting the foregoing,
unless expressly authorized by the applicable content
owner or service provider, you may not modify, copy,
republish, upload, post, transmit, translate, sell, create
derivative works, exploit, or distribute in any manner
or medium any content or services displayed through
this device.
YOU EXPRESSLY ACKNOWLEDGE AND AGREE
THAT USE OF THE DEVICE IS AT YOUR SOLE
RISK AND THAT THE ENTIRE RISK AS TO
SATISFACTORY QUALITY, PERFORMANCE
AND ACCURACY IS WITH YOU. THE DEVICE
AND ALL THIRD PARTY CONTENT AND
SERVICES ARE PROVIDED “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED. TCL EXPRESSLY DISCLAIMS
ALL WARRANTIES AND CONDITIONS WITH
RESPECT TO THE DEVICE AND ANY CONTENT
AND SERVICES, EITHER EXPRESS OR,
IMPLIED, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY, OF
SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, OF ACCURACY, OF
QUIET ENJOYMENT, AND NON-INFRINGEMENT
OF THIRD PARTY RIGHTS. TCL DOES NOT
GUARANTEE THE ACCURACY, VALIDITY,
TIMELINESS, LEGALITY, OR COMPLETENESS OF
ANY CONTENT OR SERVICE MADE AVAILABLE
THROUGH THIS DEVICE AND DOES NOT
WARRANT THAT THE DEVICE, CONTENT OR
SERVICES WILL MEET YOUR REQUIREMENTS,
OR THAT OPERATION OF THE DEVICE OR
SERVICES WILL BE UNINTERRUPTED OR
ERROR-FREE. UNDER NO CIRCUMSTANCES,
INCLUDING NEGLIGENCE, SHALL TCL BE LIABLE,
WHETHER IN CONTRACT OR TORT, FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES, ATTORNEY FEES,
EXPENSES, OR ANY OTHER DAMAGES ARISING
OUT OF, OR IN CONNECTION WITH, ANY
INFORMATION CONTAINED IN, OR AS A RESULT
OF THE USE OF THE DEVICE, OR ANY CONTENT
OR SERVICE ACCESSED BY YOU OR ANY THIRD
PARTY, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
Third party services may be changed, suspended,
removed, terminated or interrupted, or access may be
disabled at any time, without notice, and TCL makes
no representation or warranty that any content or
service will remain available for any period of time.
Content and services are transmitted by third parties
by means of networks and transmission facilities
over which TCL has no control. Without limiting
the generality of this disclaimer, TCL expressly
disclaims any responsibility or liability for any change,
interruption, disabling, removal of or suspension
of any content or service made available through
this device. TCL may impose limits on the use of
or access to certain services or content, in any
case and without notice or liability. TCL is neither
responsible nor liable for customer service related to
the content and services. Any question or request for
service relating to the content or services should be
made directly to the respective content and service
providers.