Thomson 55FB3103 User Manual
Displayed below is the user manual for 55FB3103 by Thomson which is a product in the Hospitality TVs category. This manual has pages.
Related Manuals
EN 1
Important information
Safety
Ensure that your domestic mains supply voltage matches the
voltage indicated on the identication sticker located at the
back of your set. Where the mains plug or an appliance coupler
is used as disconnect device, it shall remain readily operable.
On certain models, the light indicator is located at the side of
the TV set. The absence of a light indication at the front does
not mean that the TV set is fully disconnected from the mains.
To disconnect the TV set completely, the mains plug must be
pulled out.
The TV set’s components are sensitive to heat. The maximum
ambient temperature should not exceed 35º Celsius. Do
not cover the vents at the back or sides of the TV set. Leave
sufcient space around it to allow adequate ventilation. Install
the appliance away from any source of heat (replace, etc.) or
appliances creating strong magnetic or electric elds.
Moisture in rooms where the set is installed should not exceed
80% humidity. Moving the set from a cold place to a warm
one can cause condensation on the screen (and on some
components inside the TV set). Let the condensation evaporate
before switching the TV set on again.
WARNINGS
This appliance is intended for domestic household use only
and should not be used for any other application, such as for
non-domestic use or in a commercial environment.
If the external exible cable or cord of this product is damaged,
it shall be replaced by the manufacturer or his service agent or
a similar qualied person in order to avoid a hazard.
Leave more than 10cm clearance around the television to
allow adequate ventilation. The ventilation should not be
impeded by covering the ventilation openings with items, such
as newspapers, table-cloths, curtains, etc.
The apparatus shall not be exposed to dripping or splashing
and no objects lled with liquids, such as vases shall be placed
on the apparatus.
To prevent the spread of re, keep candles or other
open ames away from this product at all times.
WARNING: To prevent injury, this apparatus must be securely
attached to the oor/wall in accordance with the installation
instructions.
CAUTION: Connect headphones with the volume set low and
increase if required. Prolonged listening through headphones
at high volume settings can result in hearing damage.
Eye Fatigue
When using this product as a computer monitor, health and
safety experts recommend short frequent breaks rather than
occasional longer breaks. For example a 5-10 minute break
after an hour of continuous screen work is considered to be
better than a 15 minute break every 2 hours.
Do not use the monitor against a bright background or where
sunlight or other bright light sources will shine directly onto the
screen.
The or POWER/ button on the TV set or the button
on the remote control can be used to switch it on and put it
into standby mode. If you are not going to be watching the
TV for a lengthy period of time, switch it off completely by
removing the plug from the mains power socket.
During thunderstorms, we recommend that you disconnect
the TV set from the mains and aerial so that it is not affected by
electrical or electromagnetic surges that could damage it. For
this reason, keep the mains and aerial sockets accessible so
they can be disconnected, if necessary.
Unplug the TV set immediately if you notice it giving off a
smell of burning or smoke. You must never, under any
circumstances, open the TV set yourself, as you run the risk of
an electric shock in doing so.
TV screen
The TV screen used in this product is made of glass. Therefore,
it can break when the product is dropped or impacted upon by
other objects.
The TV screen is a very high technology product, giving you
nely detailed pictures. Occasionally, a few nonactive pixels
may appear on the screen as a xed point of blue, green or
red. This does not affect the performance of your product.
Care
Use a glass-cleaning product to clean the screen and a soft
cloth and mild detergent to clean the rest of the set.
Important: Using strong detergents, alcohol-based and
abrasive products may damage the screen.
Dust the vents at the back and sides regularly. Using solvents,
abrasive or alcohol-based products could damage the TV set.
If an object or liquid enters the appliance, unplug it immediately
and have it checked by an authorized engineer. Never open
the appliance yourself since this may put you at risk or damage
the appliance.
Hanging the TV set on the wall
Warning: This operation requires two people.
To ensure a safe installation, observe the following safety
notes:
• Check that the wall can support the weight of the TV set and
wall mount assembly.
• Follow the mounting instructions provided with the wall
mount. For certain models, make sure to screw the
hexagonal VESA wall mounting screw bosses (and screws)
provided with the set into the nuts for the wall mount at the
back of your set before your wall mounting.
• The TV set must be installed on a vertical wall.
• Make sure to use only screws suitable for the material of the
wall.
• Make sure that the TV set cables are placed so that there is
no danger of tripping over them.
All other safety instructions about our TV sets are also
applicable here.
Placing the TV on a table and other surfaces
Before setting up your television set, make sure that the
surface you want to put the set on can support its weight.
Do not place the set on an unstable surface (e.g. moving
shelf, very edge of a unit) and make sure that the front of the
television set does not overhang the surface it is standing on.
To avoid TV from falling please fasten TV to the wall by using
necessary screws (in Vesa wall mount holes), clamps, anchors
to be bought separately. Install TV near to the wall to avoid
falling backwards.
Multi product user manual
The features described in this manual are common to most
models. Some features may not be available on your TV and/
or your TV may include features that are not described in this
user manual. The illustrations in this manual may differ from
the actual product. Please refer to the actual product.
EN 2
Information for Users on Disposal of Old
Equipment and Batteries
[European Union]
These symbols indicate that the electrical and
electronic equipment and the battery with this
symbol should not be disposed of as general
household waste at their end-of-life. Instead, the
products should be handed over to the applicable
collection points for the recycling of electrical
and electronic equipment as well as batteries
for proper treatment, recovery and recycling in
accordance with your national legislation and the
Directive 2002/96/EC and 2006/66/EC.
By disposing of these products correctly, you
will help to conserve natural resources and will
help to prevent potential negative effects on
the environment and human health which could
otherwise be caused by inappropriate waste
handling of these products.
For more information about collection points and
recycling of these products, please contact your
local municipal ofce, your household waste
disposal service or the shop where you purchased
the product.
Penalties may be applicable for incorrect disposal
of this waste, in accordance with national
legislation.
[Business users]
If you wish to dispose of this product, please
contact your supplier and check the terms and
conditions of the purchase contract.
[Other Countries outside the European Union]
These symbols are only valid in the European
Union. If you wish to dispose of these items,
please do so in accordance with applicable
national legislation or other rules in your country
for the treatment of old electrical equipment and
batteries.
Notice:
The sign Pb
below the
symbol for
batteries
indicates that
this battery
contains lead.
Dear Customer,
This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and
electrical safety.
TCL Operations Polska Sp. z o.o.
ul. A. Mickiewicza 31/41
96-300 Żyrardow, Poland
Email address: zyeee@tcl.com
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance. Product design
and specications may be changed without notice.
Products
Battery
English
EN 3
Contents
Important information ………………………………… 1
Chapter 1 - Connections
Connecting the power and antenna ………………… 4
DVD recorder, cable receiver ………………………… 4
DVD player, home theatre system, PC, headphones …5
Blu-ray Disc player, HD game console &
HD camcorder ………………………………………… 5
Chapter 2 - Getting started
Remote control functions …………………………… 6
Switching the TV on and off ………………………… 7
Chapter 3 - Installing channels
Initial setup …………………………………………… 8
Performing an automatic channel search …………… 8
Chapter 4 - Using your TV
Accessing channels …………………………………… 9
Watching connected devices ………………………… 9
Volume ………………………………………………… 9
Using TV menus ……………………………………… 9
Selecting menu language …………………………… 9
Chapter 5 - Using more of your TV
Setting up your favourite channels ……………… 10
ECO settings ………………………………………… 10
Audio description …………………………………… 10
Using subtitles ……………………………………… 10
Turning on/off subtitles ……………………………… 10
Enabling subtitle languages on digital TV channels 10
Selecting a subtitle type on digital TV channels … 10
Selecting decoding page language in Teletext … 10
Digital Teletext language …………………………… 10
SPDIF type ………………………………………… 10
T-Link ………………………………………………… 11
Enabling or disabling T-Link ……………………… 11
Using one-touch play ……………………………… 11
Using system standby ……………………………… 11
Common interface ………………………………… 11
Using the common interface module ……………… 11
Accessing common interface services …………… 11
Software update …………………………………… 11
Changing to Shop or Home mode ………………… 11
MHEG function ……………………………………… 12
Viewing photos, playing music and watching
videos from a USB storage device ……………… 12
Photo ………………………………………………… 12
Music ………………………………………………… 12
Video ………………………………………………… 12
Time access ………………………………………… 13
Diagnostics on digital TV channels ……………… 13
Reset shop ………………………………………… 13
Customising the input settings …………………… 13
Using Electronic programme guide ……………… 13
PVR (Personal Video Recorder) ………………… 13
Schedule list ………………………………………… 14
MHL (Mobile High-Denition Link) ………………… 14
Connecting MHL-compatible Device ……………… 14
When using MHL …………………………………… 14
Chapter 6 - Other information
Password in Parental Control …………………… 15
Troubleshooting …………………………………… 15
Television specications …………………………… 15
Operating Conditions ……………………………… 15
Storage Conditions ………………………………… 15
OSS Notice ………………………………………… 15
EN 4
OUT
IN
ANTENNA
IN
OUT
OUT
IN
ANTENNA
OUT
Chapter 1 Connections
Connecting the power and antenna
To switch on TV after connecting power cord, press or POWER/ .
Note: Position of power socket varies according to TV model. On certain models, you have to turn on the power
switch first.
Note: Disconnect the power cord before connecting devices.
Cable
DVD recorder, cable receiver
Cable
DVD
recorder
Set-top
box
Chapter 1 - Connections
English
EN 5
OUT
HDMI
OUT
DVD player, home theatre system, PC, headphones
Notes:
- Before connecting a PC, set the PC monitor refresh rate to 60Hz.
- The connectors of VGA and CMP (YPbPr) share the same audio input connector.
- Excessive sound pressure from earphones and headphones can cause hearing loss.
- It is recommended to use as short as possible high quality HDMI cables to avoid possible interferences.
- It is recommended to use 1m long or shorter VGA cable with ferrite beads in case VGA input is available in
TV and TV is connected using VGA cable. Maximum supported VGA resolution is 1024x768/60Hz.
DVD player/
Home theatre system
PC
Or use an HDMI
connection.
Blu-ray Disc player, HD game console & HD camcorder
Notes:
- ARC (Audio Return Channel) function is only supported on HDMI 1 (ARC) port.
- Number of HDMI ports may vary.
- USB connector is for data input from USB storage devices.
- All USB devices have to be directly connected to TV set without cable extenders.
In case extender is required it has to be as short as possible and equipped with
ferrite beads.
- MHL (Mobile High-Definition Link) function allows you to link an MHL-capable
mobile device to the television and is only supported on the TV HDMI port
identied with MHL.
Notes:
- Not all connections available on all models.
- The location of the power socket on the TV may vary according to TV model.
- The positions and names of the function buttons and connectors on the TV may vary according to
TV model.
HD Camcorder
Blu-ray Disc
player
HD game console
Connections
EN 6
Source To select connected devices.
Standby/quit standby.
0-9 To select a channel, page or setting.
ECO To select desired power saving mode.
Guide To toggle the Electronic Programme Guide on or off (only available for digital
channels).
Menu To access the main menu; to return to the previous menu.
Exit To exit the menu structure or Teletext.
▲▼ To navigate in the main menu; to select menu options; to switch to the
previous or next photo, song or video in USB function.
◄►
/*Zoom+/-
To navigate in the main menu; to set functions and change values. ► can
also be used to open the corresponding submenu.
* To select the picture format.
Note: You are recommended to use the full screen mode. Do not use the
display mode with black bars on both sides of the picture (such as 4:3) for a
long time, otherwise the TV screen may be damaged permanently.
OK To open the corresponding submenu and activate a setting in menus; to
freeze/unfreeze the picture in digital TV mode.
Option To display the function menu to perform certain operations; to display the
Teletext page in different modes.
Return To return to the previous channel; to return to the previous menu in USB
function.
V+/- To control the volume.
Info To display programme information, if available.
Mute To switch the sound off and back on.
P+/- To change channels.
TEXT To toggle Teletext on or off.
SUBTITLE To select a subtitle language available for selected digital TV programme.
LIST To display channel list.
TV To access TV mode.
Colour
buttons
To select tasks or Teletext pages. The red button can also be used for MHEG
function.
Lang To select a sound type available for selected analogue TV programme; to
select an audio language available for selected digital TV programme.
Remote control functions
Most of your television's functions are available via the menus that appear on the screen. The remote control
supplied with your set can be used to navigate through the menus and to congure all the general settings.
Chapter 2 Getting started
V P
ECO
Source
Mute
Menu Exit
Guide
Zoom Zoom
Option
Return
Info
Lang
＋－
Chapter 2 - Getting started
English
EN 7
Important:
Batteries shall not be exposed to excessive heat such as sunshine, re or the like. Remove batteries when
the remote control is not to be used for a long time. Batteries left in equipment may cause damage through
deterioration and corrosive leakage, invalidating the guarantee.
To protect the environment use local recycling facilities for battery disposal. Dispose of used batteries
according to the instructions.
CAUTION: Risk of explosion if batteries are replaced by an incorrect type. Replace only with the same or
equivalent type recommended by the equipment manufacturer.
If the batteries in your remote control are run down, you can use the buttons on your TV set. In TV mode,
they have the same functions as the corresponding buttons on the remote control. The OK button on the TV
set can be pressed repeatedly to select the required source. In the menus they have the following functions:
For models with OK button on the set: For models without OK button on the set:
PR+ or PR ▲ ▲ PR+ or PR ▲ ►
PR- or PR ▼ ▼ PR- or PR ▼ ◄ & OK
VOL+, + or VOL ► ► VOL+, + or VOL ► ▲
VOL-, - or VOL ◄ ◄ VOL-, - or VOL ◄ ▼
MENU or Menu MENU or Menu
OK OK
Getting started
Switching the TV on and off
1. When the power cord is connected, the TV will be turned on directly or be in standby mode. If the TV is in
standby mode, press the or POWER/ button on the set or the button on the remote control to turn it
on.
2. To put the TV into standby mode, press the or POWER/ button on the set or the button on the remote
control. The TV set remains powered up, but with low energy consumption.
3. To switch off the TV, unplug the mains plug from the mains outlet.
(*On certain models, you have to turn on the power switch rst.)
EN 8
Installing channels Chapter 3
Chapter 3 - Installing channels
Initial setup
Initial setup involves selecting all the settings required
to be able to search for and store all the analogue
and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specied hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The rst time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process. (Refer to Figure 1.)
1. Press ▲/▼ to select your language, then press
OK/► to enter the next step.
2. Press ▲/▼ to select your country, then press
OK/► to enter the next step.
Note: If you select France, you will have to
enter the Password setting menu here in
order to set a password. Use the numeric
buttons to enter a four-digit number for your
password. (0000 is too simple to be set as
your password.) Re-enter the same code
to confirm the password. After that, you will
enter the next step automatically. (In this
step, you can only press ◄ to return to the
previous step.)
3. Press ▲/▼ to select your tuner mode
Antenna or Cable or Satellite. (Note:
Satellite option may not be available for certain
models.) Then follow a) or b) or c) below.
-a) If you have selected Antenna.
• Press OK/► to enter.
• Press ▲/▼ to select Digital & Analogue or
Digital or Analogue, then press OK/►.
• Press ▲/▼ to select Scan, then press OK/►
to start the automatic search for all DVB-T
digital and/or analogue channels.
-b) If you have selected Cable.
• Press OK/► to enter.
• Press ▲/▼ to select Digital & Analogue or
Digital or Analogue.
• If you select Digital & Analogue, press OK/►
to enter. Then:
-Press ▲/▼ to select Scan, then press
OK/►.
-Press ◄/► to select the scan mode if
available (Full or Advanced).
-If you select Full, press OK to start the
automatic search for all DVB-C digital and/or
analogue channels.
-If you select Advanced, use the numeric
buttons to adjust the values for frequency,
symbol rate, network ID, and use ◄/► to
select the modulation mode; then press OK
to start the search for all DVB-C digital and/
or analogue channels.
• If you select Digital, press OK/►to enter,
then follow all the same steps as for Digital
& Analogue above, to search for all DVB-C
digital channels.
• If you select Analogue, press OK/►to enter,
press▲/▼to select Scan, then press OK/► to
start the search for all analogue channels.
-c) If you have selected Satellite.
• Press OK/► to enter.
• Press ▲/▼ to select one antenna type.
• Press OK/► to select one satellite, then press
OK to enter the next step to configure proper
information related to this satellite. Press OK
to go back after finishing settings.
• Press ► to start scanning.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4. Before starting the scanning, you can also select
Skip scan to skip the initial setup process. In this
case, to search and store your channels you may
do an automatic channel search by following the
instructions in the next section Performing an
automatic channel search.
5. During the setup, you can follow the hints
available at the bottom of the screen to return to
the previous step by pressing ◄. Or press Exit to
exit or interrupt the search halfway.
6. Once the automatic search ends, the set enters
the next step automatically. Press ▲/▼ to select
your location Shop or Home. Press OK/► to
confirm your selection and enter the last step.
7. - In this step, you can press OK to exit the initial
setup. The channels are arranged in a preset
order. If you wish to skip channels, modify the
preset order or rename channels, select Setup >
Organiser and press OK/► to enter.
-In this step, you can also press ◄ to return to
the previous step.
Performing an automatic channel search
This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels. This may be done in
any of the cases below :
-you have selected Skip scan in the Initial setup
-you see “Please scan channels!” in TV mode
-you want to update your channels.
1. Press Menu on the remote control and select
Setup > Language > Menu language. Press
◄/► to select your desired menu language.
2. Press Menu to return to Setup. Press ▲/▼ to
select Country, then press ◄/► to select your
country. The TV installs and arranges channels
English
EN 9
Using your TV Chapter 4
according to your country. At this step, you will be
requested to enter your password.
3. Press ▲/▼ to select Tuner mode, then press
◄/► to select Antenna or Cable or
Satellite. (Note: Satellite option may not be
available for certain models.) Then follow a) or b)
or c) below.
-a) If you have selected Antenna.
• Press ▲/▼ to select Channel install, and
press OK/► to enter.
• Select Automatic search (Refer to Figure 2.),
then press OK/► to display Automatic search.
• Press OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
• Select Digital & Analogue or Digital or
Analogue, then press OK/► to start the
automatic search, which relates to all DVB-T
digital and/or analogue channels.
-b) If you have selected Cable.
• Press ▲/▼ to select Channel install, and
press OK/► to enter.
• Select Automatic search, then press OK/► to
display Automatic search.
• Press OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
-If you select Digital & Analogue, then
press OK/► to enter. Select your scan
mode if available and configure proper cable
information in the same way as in Initial
setup. Press ▲/▼ to select Scan and press
OK/► to start your automatic search relating
to all DVB-C digital and analogue channels.
-If you select Digital, then follow the same
process as above to start your automatic
search relating to all DVB-C digital channels.
-If you select Analogue, then press OK/►
to start your automatic search relating to all
analogue channels.
-c) If you have selected Satellite.
• Press ▲/▼ to select Channel install, and
press OK/► to enter.
• Select Automatic search, then press OK/►
to enter. You can select a proper satellite or an
operator.
• Press OK to go to the next step. Before you
start scanning, you can press OK to edit the
parameters of the selected satellite. Then
with your desired options of Scan mode and
Channels, select Scan and press OK/► to
start scanning.
4. The search may take a few minutes. During the
process, you can press Menu to abort halfway.
5. Once the automatic search ends, press Menu to
return to the previous step or press OK to restart
your channel search.
6. After the automatic search, channels are arranged
in a preset order. If you wish to skip channels,
modify the preset order or rename channels,
select Setup > Organiser and press OK/► to
enter.
Chapter 4 - Using your TV
Using your TV
Accessing channels
Using the numeric buttons: press the corresponding
numeric buttons to access the channels.
Using the PR+/- or P+/- buttons: scroll through the
channels.
Watching connected devices
There are three ways for you to select connected
devices on your TV:
• you can press Menu on the remote control and
select Source.
• you can use the OK button to enter, then press
▲/▼ and OK to select your wanted connected
devices
• you can also repeatedly press Source on the
remote control or OK on the TV set to toggle
between TV and other input sources.
To resume TV viewing, you can press any numeric
button.
Note: Not all models have OK button on the set.
Volume
Volume control: use the VOL+/- or VOL ◄/► buttons
on the TV set or V+/- buttons on the remote control to
increase or decrease the volume.
Sound mute: press the Mute button to temporarily
mute the sound. Press this button again or the V+
button to restore it.
Using TV menus
1. Press Menu to display the main menu. (Refer to
Figure 3.)
2. Press ▲/▼/◄/► to select the desired item, then
press OK to open the corresponding submenu.
3. In submenus, use ▲/▼ to select menu options,
use ◄/► to set functions or change values. Use
OK to activate a setting. Use OK/► to open the
corresponding submenu.
4. Press Menu to return to the previous menu.
5. Press Exit to close the menu.
Note: Some options may not be available for
certain signal sources.
Selecting menu language
You can choose your preferred menu language
following the instructions below.
1. Press Menu to display the main menu.
2. Press ▲/▼/◄/► to select Setup, then press OK
to enter.
EN 10
Using more of your TV
3. Select Language and press OK/► to enter.
4. Select Menu language and press ◄/► to select
your desired language to display the menus.
5. Press Exit to close the menu.
Chapter 5 - Using more of your TV
Using more of your TV
Setting up your favourite channels
You can create a list of your favourite TV channels.
1. Press LIST.
2. Press the yellow button to enter Channel list
selection. Press ▲/▼ to select the favourite list
and press OK to enter.
3. Press the blue button to start editing your favourite
list. Press ▲/▼ to scroll through the channel list
and press OK to select or deselect it.
4. Repeat this procedure to set up other favourite
channels.
5. Press LIST/Exit to exit.
ECO settings
1. Press Menu on the remote control and select
Picture > ECO settings, press OK/► to enter
ECO settings.
2. Press ◄/► to select desired power saving mode
to achieve the desired power saving effect. The
Picture preset option under Picture will now be
set to Personal simultaneously.
3. Press Exit to close the menu.
Shortcut operation: Press ECO on the remote
control to perform the same function mentioned
above.
Audio description
Audio description refers to an additional narration
track for Blind and visually impaired viewers of visual
media, including television programmes and movies.
The description narrator talks through the presentation
describing what is happening on the screen during
the natural pauses in the audio (and during dialogue if
deemed necessary).
You can use this feature if the current broadcast
contains audio description.
1. Press Menu on the remote control and select
Sound.
2. Press OK to enter.
3. Use ▲/▼ to select Audio Description, press
OK/► to enter, use ◄/► to turn this function on
or off. Volume level can be adjusted by using the
Audio Description menu.
Using subtitles
You can enable subtitles for each TV channel.
Subtitles are broadcast via Teletext or DVB-T/DVB-C
digital broadcasts. With digital broadcasts, you have
the additional option of selecting a preferred subtitle
language.
Turning on/off subtitles
1. Press Menu on the remote control and select
Options > Subtitle.
2. Press OK/► to enter. (Refer to Figure 4.)
3. Select the Subtitle option, and press ◄/► to
select On/Off to turn on/off subtitles.
Enabling subtitle languages on digital TV channels
1. Press Menu on the remote control and select
Options > Subtitle > Digital subtitle language.
2. Press ◄/► to select a subtitle language as your
preferred language.
3. Press ▲/▼ to select Digital subtitle language
2nd.
4. Press ◄/► to select a secondary subtitle
language.
5. Press Exit to close the menu.
Shortcut operation: Press SUBTITLE on the remote
control to directly select a subtitle language available
for the selected digital TV programme.
Selecting a subtitle type on digital TV channels
1. Press Menu on the remote control and select
Options > Subtitle > Subtitle type.
2. Press ◄/► to select a subtitle type. You can
select Hearing impaired to display the hearing
impaired subtitles with your selected language.
Selecting decoding page language in Teletext
Press Menu on the remote control and select
Options > Decoding page language. Select a
proper type of language in which Teletext will display.
Digital Teletext language
On digital TV channels, depending on the broadcaster,
you may be able to enjoy a service with multiple initial
Teletext pages in different languages. This function
allows you to select an available language as primary
language, which relates to different initial Teletext
pages.
Press Menu on the remote control and select
Options > Digital teletext language. Press ◄/► to
select.
SPDIF type
Connect the TV to an audio device through the SPDIF
output. To select a proper sound type for your SPDIF
output, press Menu on the remote control and select
Options > SPDIF type.
-If you select PCM, the SPDIF output format is
PCM, regardless of the programme’s sound
format.
-If you select Dolby D, the SPDIF output format is
• Dolby Digital when the programme’s sound format
is Dolby Digital or Dolby Digital Plus or HE-AAC
• PCM when the programme’s sound format is
MPEG.
Chapter 5
English
EN 11
Using more of your TV
-If you select Off, this turns off the audio output
from the audio device connected to the SPDIF
output.
Note: The options you may choose depend on
the programme you are watching. If you
select PCM and the sound is ahead of the
picture, you can select SPDIF delay from
the Options menu and press ◄/► to adjust
the delay time to synchronize the sound with
the picture.
T-Link
Use this function to search for CEC devices connected
to the HDMI sockets in your TV and enable one-touch
play and one-touch standby between CEC devices.
Enabling or disabling T-Link
1. Press Menu on the remote control, then select
Options > T-Link.
2. Press ◄/► to select On or Off, if this function
is turned on, T-Link option will be available in
the Quick access menu which you can enter by
pressing the Option button on the remote control.
Using one-touch play
With one-touch play, pressing the play button on (for
example) your DVD remote control starts playback on
your DVD device and automatically switches your TV
to the correct source, displaying DVD content.
Using system standby
With system standby, pressing the button on (for
example) your TV remote control switches your TV
and all connected HDMI devices to standby mode.
Note: Guide Menu will be available in the sublist
of T-Link option when T-Link function is
turned on and CEC devices are connected.
With this function, you can operate CEC
devices with a virtual on-screen controller
and the TV remote control.
Note: The CEC functions depend on the devices
connected and it is possible that some
devices may not interoperate correctly when
connected to this TV. The user manual or
the manufacturer of the problematic devices
should be consulted for further information.
Common interface
Encrypted digital TV channels can be decoded with a
common interface module and a card provided by a
digital TV service operator.
The common interface module may enable several
digital services, depending on the operator and
services you choose (for example, pay TV). Contact
your digital TV service operator for more information
about services and terms.
Using the common interface module
WARNING: Switch off your TV before inserting a
common interface module. Be sure to follow the
instructions described below. Wrong insertion of
a common interface module may damage both the
module and your TV.
1. Following the directions printed on the common
interface module, gently insert the module into the
common interface slot on the TV.
2. Push the module in as far as it will go.
3. Turn on the TV and wait for the common interface
function to be activated. This may take several
minutes.
Note: Do not remove the common interface
module from the slot. Removing the module
will deactivate the digital services.
Accessing common interface services
After inserting and activating the common interface
module, press Menu on the remote control and select
Options > Common interface.
This menu option is only available if the common
interface module is correctly inserted and activated.
On-screen applications and content are provided by
your digital TV service operator.
Software update
Press Menu on the remote control and select
Options > Software update. Press OK/► to enter.
(Refer to Figure 5.)
-Current version: Displays the current version of
the software.
-Product name: Displays the product name of your
set.
-Serial number (if available): Displays the serial
number of your set.
-OAD (Over Air Download): Enables you to install the
latest version of the software if available from the
broadcast. Select OAD and press OK/► to enter.
• Use ◄/► to select Yes under Auto download
to automatically download the latest software if
available. After the software has been downloaded
successfully, you will be prompted to decide if you
want to install it right now. If yes, follow the on-
screen instructions to complete your installation.
You can also select to ignore the installation here.
• Select No under Auto download to decline the
automatic download.
• Select Manual OAD download and press OK/►
if you wish to search manually for the latest
software. Follow the on-screen instructions to
complete. During the search, press OK/Exit if you
wish to cancel or exit the process.
Changing to Shop or Home mode
1. Press Menu on the remote control and select
Options > Location.
EN 12
Using more of your TV
2. Press ◄/► to select your location Shop or Home.
3. Press Exit to exit.
Note: According to the regulation of European
Commission 2009/125/EC, in Home mode, TV
will be put into standby mode automatically if
there is no operation in 4 hours. This feature
can be deactivated in Options menu.
MHEG function
Some digital TV broadcasters offer dedicated digital
text or interactive services (for example, BBC1).
These services work like normal Teletext with the
addition of number, colour and navigation buttons.
1. Press Menu on the remote control and select
Options > Subtitle > Subtitle.
2. Press ◄/► to set Subtitle to Off.
Note: For some models, MHEG and subtitles are
mutually exclusive and cannot coexist on the
same screen. If Subtitle is set to On, MHEG
will not appear.
3. Press the red button or TEXT on the remote
control.
4. Press ▲/▼/◄/► to select or highlight items.
5. Press OK to confirm or activate.
6. Press one of the colour buttons to select an
option.
7. Press TEXT or Exit to exit.
Viewing photos, playing music and watching
videos from a USB storage device
Your TV is tted with a USB connector that enables
you to view photos, listen to music or watch videos
stored on a USB drive.
Supported le formats:
Photo JPEG
Music MP3
Video AVI, MP4, MPG, MPEG, TS…
Notes: Some USB keys and USB products like
digital cameras or mobile phones are not
fully compatible with USB 2.0 standard so
they may not work with the TV multimedia
player. Not all USB keys or devices are
compatible with the USB function. Not all
above formats are recognised. The encoding
formats of your files will determine whether
or not they can be used.
When a USB drive is detected, the TV enters the
Media center menu directly. To enter the Media
center menu manually, press Menu on the remote
control and select Media.
Photo
Use this function to display photos, if available.
1. Select Media center > Photo, then press OK to
enter the main file content browser.
2. In the main file content browser, use ▲/▼/◄/► to
select a photo or an inner file folder.
3. Select an inner file folder, press OK to enter a sub
file content browser.
4. Use ▲/▼/◄/► to select a photo in either main or
sub file content browser, press Menu to display
the photo menu in folder mode.
-Sort: Sort folders and photos by modification
Date or Name.
-Edit: Copy, paste or delete a selected photo.
-Parser: You can select Recursive to display
photos from all sub file folders.
5. Select a photo, press OK to watch, and a slide
show begins from the selected photo. Press OK to
pause the photo. Press Menu to display the photo
menu in the browser mode. You can play, pause
or rotate the photo, select different play modes
and display effects, etc.
6. Press the related buttons on the remote control
to perform the available functions shown on the
function bar at the bottom of the TV screen. Press
the Info button to show or remove the function bar.
Music
Use this function to play back music, if available.
1. Select Media center > Music, then press OK to
enter the main file content browser.
2. Use ▲/▼/◄/► to select a song in either main or
sub file content browser in the same way as in
photo display function, press Menu to display the
music menu in folder mode.
-Sort: Sort folders and songs by Name, Genre,
Artist or Album.
-Edit: Copy, paste or delete a selected song.
-Parser: You can select Recursive to display
songs from all sub file folders.
3. Select a song, press OK to play, and automatic
playback begins from the selected song. Press
Menu to display the music menu in the browser
mode. You can play or pause the song, select
different play modes, etc.
-Show lyrics: This option is available for the
songs with lyrics. Select it and use ◄/► to turn
on/off lyrics synchronized display.
-Audio only: Select and press OK to listen to the
music with the screen turned off. Any key press
will turn the screen on.
4. Press the related buttons on the remote control
to perform the available functions shown on the
function bar at the bottom of the TV screen.
Video
Use this function to watch videos, if available.
1. Select Media center > Video, then press OK to
enter the main file content browser.
2. Use ▲/▼/◄/► to select a video in either main
or sub file content browser in the same way as in
English
EN 13
Using more of your TV
photo display function, press Menu to display the
video menu in folder mode.
-Sort: Sort folders and videos by Type,
modification Date or Name.
-Edit: Copy, paste or delete a selected video.
-Parser: You can select Recursive to display
videos from all sub file folders.
3. Select a video, press OK to watch, and automatic
playback begins from the selected video. Press
Menu to display the video menu in the browser
mode. You can play or pause the video, select
different play modes, screen modes and preset
picture settings, etc.
4. Press the related buttons on the remote control
to perform the available functions shown on the
function bar at the bottom of the TV screen. Press
the Info button to show or remove the function bar.
Time access
You can access the time from digital channels
following the instructions below.
1. Press Menu on the remote control and select
Timer > Clock > Auto synchronization.
2. Press ◄/► to select On.
Diagnostics on digital TV channels
1. Press Menu on the remote control and select
Setup > Diagnostics.
2. Press OK/► to display some signal information
on the current digital channel, such as signal
strength, frequency, etc.
Reset shop
Allows you to reset the TV to factory default settings.
1. Press Menu on the remote control and select
Setup, then press OK to confirm.
2. Select Reset shop and press OK/► to enter.
3. Use the numeric buttons to enter the password.
4. Press ◄/► to select OK and press OK to confirm.
5. The Initial setup menu appears. Follow the
related instructions.
Customising the input settings
You can congure your TV according to the
equipment you connect to it.
1. Press Menu on the remote control and select
Setup > Input settings.
2. Press OK/► to enter Input settings.
3. Press ▲/▼ to select a connector your equipment
is connected to.
4. Press ◄/► to select the type of apparatus
attached to this connector.
5. Press Menu to return to the Setup menu.
After conguring, the selected source label will be
displayed after the name of the related connector in
the source list when selecting Source in the Menu or
pressing Source on the remote control or OK on the
TV set.
Note: Not all models have OK button on the set.
Using Electronic programme guide
EPG is an on-screen guide that displays scheduled
TV programmes. You can navigate, select, view and
record programmes.
1. Press Guide on the remote control, the Now
and Next EPG menu will appear, which allows
you to get information about the current or next
programme playing on each channel. Navigate
through the different programmes using the
navigation buttons on the remote control.
2. Use the colour buttons to view the 8 Days EPG.
-Prev day (Red): List the previous day’s EPG.
-Next day (Green): List the next day’s EPG.
-View detail (Yellow): Display the description of
this programme if available.
-Type filter (Blue): Programme guide filter for
digital TV programmes.
• Press the blue button to display the programmes’
type and subtype (if available) lists.
• Navigate through the different types and
subtypes using the navigation buttons on the
remote control.
• Select one or more types, which you want to
highlight from the Type list, press OK to select (or
deselect). A checkmark will appear to the left of
the type when selected. When you select a type,
all its subtypes will be selected accordingly.
• Also, you can select some desired subtypes
without selecting any type first.
• Press the blue button to exit the type and
subtype list.
• After filtering, all your desired digital TV
programmes will be highlighted.
-Add schedule (Option): Press Option on the
remote control to bring up the Schedule list
menu. For details on scheduled recording, refer
to the Schedule list section.
3. Press Guide/Exit to exit the EPG and switch to
the selected channel.
PVR (Personal Video Recorder)
Allows you to record non encrypted TV programmes.
Before you use the function, connect a USB drive to
the set rst.
Note: Feature is available only in selected products
and, due to specific TV network limitations and
country technical requirements, might not be
available in product or place of installation.
Feature might also be blocked by TV network
due to copyright protection (HD content,
recording protection). Please use Option on the
remote control to check if feature is available in
your product.
EN 14
Other informationChapter 6
1. Press Option on the remote control and select
Quick access > PVR.
2. Press OK/► to enter.
3. Press:
-the red button to start recording, the record file is
put into a folder named after the channel number
under the PVR folder in Media center > Video;
-▲/▼/◄/► to adjust the recording duration.
-the green button to stop recording manually;
in normal operation, the recording will stop
automatically when the recording duration has
passed.
4. In recording, PVR mini pane will also show on the
screen to indicate the recording progress.
5. To watch the recorded programme, exit PVR
mode first and go to Media center > Video. Select
the folder PVR, then select the related record file.
Press OK to play. (It is the same if you record a
digital radio programme).
Notes:
- Feature available only for digital non encrypted
channels. Even when CICAM (CI or CI+) is
inserted, feature is not available on encrypted
channels.
- Only supports USB drive of FAT32 format.
- Before you connect the USB drive to the set,
make sure you have backed up the data in the
drive to avoid the loss of your important data due
to unforeseen malfunction.
- The bigger the USB drive free memory for the
PVR function, the bigger the recording length.
- If you want to change channel or signal source
during recording, store the recording data before
changing the channel or source.
- The set cannot play files normally if the
parameters of the file exceed the limitations of
the system, the file format is not supported, the
file is damaged, or the file cannot be decoded.
- Do not disconnect the USB drive when the
system is reading a file or transmitting data,
otherwise the system or the drive may be
damaged.
Schedule list
This function is used to perform scheduled recording.
1. Press Option on the remote control and select
Quick access > Schedule list.
2. Press OK/► to display the schedule list.
3. To add a schedule into your schedule list, press
the red button first to display Schedule list. Then,
-Channel number: use ◄/► to select the
channel number.
-Start date: use the numeric buttons to set the
recording date.
-Start time: set the start time of the recording.
-Stop time: set the stop time of the recording.
-Schedule type:
• Set Reminder to be reminded that you can
switch to the scheduled programme when the
time you have set comes. When time is out
and you do not execute any operation, the
dialogue box will disappear and no further
operation will be executed.
• Set Record if you really want to start your
scheduled recording when the time you have
set comes. When time is out and you do not
execute any operation, scheduled recording
will start automatically.
-Repeat type: set different repeat modes for the
recording.
4. Press ▲/▼/◄/► to select Add, then press OK to
add the schedule you set into your schedule list.
5. Press the red button to repeat above procedures
to add another schedule.
6. If you wish to edit or delete a schedule, select it
and press OK to enter.
7. Press Exit to close the menu.
MHL (Mobile High-Definition Link)
(* not available for some models)
You can use the following functions by connecting the
TV HDMI port identied with MHL and the USB port of
mobile phone or similar device with an MHL cable.
• Charge your mobile phones from the TV.
• Two-way remote operation between TV and
mobile phone.
• Video/Audio output from your mobile phone.
Notes:
- These functions may not be available depending
on the connected equipment.
- If there is no more battery life left in the
connected device, charging will not start.
- To operate the mobile phone with the TV remote,
you need to turn on the T-Link function first,
then press Option and select Quick access >
T-Link > Setup > Guide Menu. Follow the
virtual keypad to do operations.
Connecting MHL-compatible Device
• Connect the MHL-compatible device to the
HDMI port identified with MHL on the TV using
an MHL cable (not supplied), charging will start
automatically.
• When connecting an MHL-compatible device to the
HDMI port identified with MHL on the TV, switch the
TV source to HDMI 2 or HDMI.
Note: Do not connect the MHL-compatible device
to any ports other than HDMI port identified
with MHL.
When using MHL
• Interoperability with MHL devices from other
English
EN 15
manufacturers is not guaranteed.
• TCL does not provide any guarantee, therefore,
against operational failure such as that described
below when an MHL source is connected to the TV.
-No picture or sound
-Some of the functions do not work by remote
operation from the TV
• If MHL does not work properly, also contact the
manufacturer of the source device for advice on its
use.
• Do not disconnect the power plug of the TV when
the TV is active and the MHL device is connected.
• Do not disconnect the power plug of the TV when
the TV is in standby mode and the MHL device is
connected.
Chapter 6 - Other information
Other information
Password in Parental Control
-The default password is 1234. You can change it to
a new one.
-The super password is 0423. If you forget your
code, enter the super password to override any
existing codes.
Troubleshooting
Please check the following list before requesting
service.
There is no picture or sound.
• Make sure the power cord is properly inserted in the
power outlet.
• Make sure the source type is set correctly.
• Make sure the antenna is properly connected.
• Make sure the volume is not set to minimum or the
sound is not set to mute.
• Make sure the headphones are not connected.
• The TV may be receiving a signal other than from
TV broadcasting stations.
Picture is not clear.
• Make sure the antenna cable is properly connected.
• Consider whether your TV signal is being properly
received.
• Poor picture quality can occur due to a VHS
camera, camcorder, or other peripheral being
connected at the same time. Switch off one of the
other peripherals.
• The ‘ghost’ or double image may be caused by
obstruction to the antenna due to high-rise buildings
or hills. Using a highly directional antenna may
improve the picture quality.
• The horizontal dotted lines shown on the pictures
may be caused by electrical interference, e.g., hair
dryer, nearby neon lights, etc. Turn off or remove
these.
Picture is too dark, too light or tinted.
• Check the colour adjustment.
Other information
• Check the brightness setting.
• Check the sharpness function.
• The LCD panel’s fluorescent lamp may have
reached the end of its service life.
Remote control does not work.
• Check the batteries of the remote control.
• Make sure the remote sensor window on the TV
front is not under strong fluorescent lighting.
• Try to clean the remote sensor window on the TV
front with a soft cloth.
If the above suggestions do not solve your technical
issue, please refer to the warranty card for service
information.
Television specifications
TV Broadcasting PAL/SECAM BG/DK/I/LL’
Receiving channels VHF/UHF/Cable
Tuner type Frequency synthesized
Operating Conditions
Temperature 5°C - 35°C (41°F - 95°F)
Humidity 20 - 80% (non-condensing)
Storage Conditions
Temperature -15°C - 45°C (5°F - 113°F)
Humidity 10 - 90% (non-condensing)
OSS Notice
This product uses software library from Freetype
Project.
This product uses software library which is distributed
under the zlib license.
This product uses UNICODE software programs
which are distributed under IBM Open source license.
This product uses glibc software programs which are
distributed under the GNU license.