TooQ Atlas User Manual
Displayed below is the user manual for Atlas by TooQ which is a product in the Standing Desks category. This manual has pages.
Related Manuals
ATLAS
TQESSD01-BK
TQESSD01-W
User manual
HEIGHT ADJUSTABLE ELECTRIC STANDING DESK
50kg
EN
List of contents for installation
EN
Connecting rod from column to motor Motor
C (x1)
Lifting column
D (x1)
Desk
E (x1)
Sync rod
F (x1)
Cross bar
G (x1) H (x1)
Power adapter
I (x1)
Cross bar
J (x1)
Power cable
K (x1)
Controller
Please check all listed components. If any of the items are missing or damaged, please contact your reseller for replacement.
Mount Adapter Bracket
EN
Contents and installation
S-A (x4)
Hexagon head screw
S-B (x4)
Phillips head screw
S-C (x6)
Phillips head screw
S-D (x4)
Hexagon head screw
S-E (x4)
Phillips head screw
S-F (x9)
Silicon pad
S-G (x6)
Washer
S-H (x4)
Cable clip
S-I (x1)
4mm Allen key
S-J (x1)
8mm Allen key
EN
Screwdriver Drill
Required tools
*Required tools to assemble the electric desk
Allen key
(included)
Bubble level
EN
Before installation
EN
• Read carefully through the manual, if you have any questions regarding instructions or warnings, please contact your local distributor.
• Ensure that you have received all parts according to the component checklist
prior to installation. II any parts are missing or faulty, telephone your local distributor for a replacement.
• Failure to fully comply with the instructions marked with “Caution”, “ “, warnings and additional information may result in serious damage to the sys-
tem or its components.
• This product can be used by adults and children from 8 years old (under supervision). Children should never be unsupervised with the product swit-
ched on. Cleaning and maintenance procedures must be carried out by an adult. Unplug the table when the system is not in use and keep the plug
out of the reach of children.
• Users with disabilities or lack of experience and knowledge about the operation of the device should be carefully supervised and instructed before
using this product.
• To avoid serious personal injury, the desktop should never be sat on.
• Check here to nd out more about bracket warranty.
EN
Electrical safety instructions:
This product is electrically operated. Please read the instructions carefully to avoid burns, re and electric shock.
Do not clean the product with water while it is plugged in.
Do not disassemble or replace components while the
power is on.
Never use the device with a damaged cord or plug.
Contact your supplier for replacement of damaged parts.
Do not operate the unit in wet environments or when its
electrical components are in contact with liquids.
Do not use the unit if the control panel emits noises or
odours.
Do not modify or handle the power supply or the control
panel.
• Do not add any elements to the adjustable joints of the
desk frame.
• Do not use the product outdoors.
.
• Remove all obstacles from the height adjustment area.
• Never leave cables or plugs out of place to avoid
possible tripping.
• It is not allowed to rebuild the desk support.
ENEN
1. Detail of adjustable electric desk
Desktop
Connecting rod from
column to motor Motor
Lifting
column
Clamp adapter
Synchronising
rod
Controller
Power adapter
Crossbar
Crossbar
EN
2. Operating the control panel
EN
Upward
movement
Downward
movement
Memory 1/2/3
Memory
Timer
Display
Indicator
Light
Note: Si el panel de control se utiliza por primera vez, por favor reinicie el sistema antes
de realizar cualquier tipo de operación.
Reboot the system:
Press and hold the “ “ button until the display shows “ “. The desk will move to the
lowest position.
Keep the button pressed, the desk will move up a little and the display will show the current
height of the desk. The reset process is now complete.
Note: Unplug and re-plug the power cord from the desk each time you want to reset the
system.
Height adjustment: Press and hold the “ “ button to raise the desk. Press and hold the
“ “ button to lower the desk.
Timer:
• Press “T” to be reminded by the system to change position. Each touch of the “T” button
takes 0.5 hour increment. The maximum time setting is 2 hours.
• After the timer has been successfully set, the indicator light on the top right will light up.
• Once the set time has elapsed, the unit will beep 3 times as a reminder to the user.
• To clear the reminder, press the “T” button until the top right indicator light turns o.
Memory setting:
• To memorise a position, press the “M” button and the display will ash “ “. Press
the 1 / 2 / 3 button while ashing.
• To recall a previously stored position, press the 1 / 2 / 3 button directly and the table will
move to the set memory position. Press any button to stop the movement.
Switching the value on the controller display between CM and INCH
• Press and hold the “T” button for approximately 3 seconds.
• When switching to metric (CM) a single beep will sound and when switching to imperial
(IN) two beeps will sound.
Note: Unplug and re-plug the power cord from your desktop each time you wish to
make a change to this setting.
Power Save Mode:
• The system will enter power save mode when it detects no activity for more than 1 minute.
When this happens the display will turn o. Press any button to activate the panel.
ENEN
3. Troubleshooting error codes
Error Solutions
ER1 Please check if the desk is overloaded.If so, remove the objects. If not, unplug and plug the power back in.
If the problem persists, contact your reseller for further assistance.
ER2 The system has experienced above-normal temperature. So, allow your desk to cool down and remain idle
forapproximately 20minutes. Never turn o the power du ring the process.
HOT Allow the desk to cool down and remain idle for approximately 20 minutes. If the problem persists, contact
your reseller for further assistance.
ER3
Cables were disconnected. Unplug and re-plug the cables between the columns and the AC adapter.
Unplug and plug the power back in and restart the system. If the problem persists, contact your reseller for
further assistance.
ER5
There are two possibilities:
1. Make sure you are using an original AC adapter.
2. An overload has occurred. Remove the items from the desk. Unplug and plug the power back in. If the
problem persists, contact your reseller for further assistance.
NEVER unplug the power supply or restart the system when it is in thermal or overload protection mode.
ENEN
4.Attachment of the engine to the lifting column
End left End right
• Insert the right end of the connecting rod into the hexagonal recess mounting
hole on the motor
• Insert the left end of the connecting rod into the hexagonal recess mounting hole
of the lifting column
• There is no matching relationship between the motor and the lifting columns.
Note: If the mounting hole on the lifting column does not match the connecting rod,
precisely adjust the mounting hole using an 8 mm Allen key to match.
• Once inserted, secure the motor to the lifting column with 2 screws from the
column side and 2 screws from the bottom using the phillips screwdriver.
EN
5. Assembly of the crossbars
• Attach the cross bar to the centre of the column with 4 screws and then attach the
cross bar a la parte superior de las columnas con 4 tornillos
6. Assembly the synchronising rod
• Loosen the knob on the right end of the synchronisation rod and attach it to the motor shaft
as shown in Figure 1. Then tighten the knob.
• Loosen the knob on the left end of the synchronisation rod and pull out the inner rod to match
the left end of the table.
• Insert the lower bar of the synchronisation rod into the hexagonal socket mounting hole of the
lifting column as shown in Figure 2.
Note: If the mounting hole on the lifting column does not match the connecting rod, precisely adjust the
mounting hole using an 8 mm Allen s panner to match.
Figure 1
(Loosen)
Figure 2
(Loosen)
End Left End Right
EN
7. Assembly of the Desktop
• Stick the 9 rubber pads in the positions closest to the holes in the frame as shown in the
picture below. Attach the adapter bracket to the cross bar.
• Carefully place the desk face down on the oor as shown.
• Turn the desk top over with the help of another person.
• Align the mounting holes found on the desk with the holes found on the desk frame.
• Insert and tighten the 6 screws and washers with a phillips screwdriver.
CAUTION: It takes at least two people to
turn the desk over, or serious physical injury
could happen.
Phillips screwdriver
EN
8. Connecting the power supply adapter
• Turn the desk over with the help of another person.
• Slide the power adapter into the adapter.
• Connect the controller with the power adapter and the motor as shown in the gure.
• Insert the power cable into the power adapter.
• Once the cables are connected, attach the cable clip to the desk.
• Attach the cable clip to the desk with the screw
EN
9. Level adjustment
Each foot pad can be adjusted independently for fine tuning.
Slightly turn the foot pad to lower or raise the base.
Advice: Use a spirit level to make sure the desk is even.
If you are using the desktop for the rst time, you need to restart the system.
Refer to the digital control panel user’s guide.
Bubble level