Trust ALKCT-2000 User Manual
Displayed below is the user manual for ALKCT-2000 by Trust which is a product in the Remote Controls category. This manual has pages.
Related Manuals
www.trust.com
SECURITY PLUS-LINE
ALKCT-2000
ALKCT-2000 ARM/DISARM REMOTE CONTROL
Item 71115 Version 1.0
Visit www.trust.com
for the latest instructions
USER MANUAL
MULTI LANGUAGE
2
4
1
3
On
O
Red LED indicator
On
O
ON button
4 sec
OFF button
Arm
O
Short press
ON button
5
6
Arm
O
ON button 3 sec
On
O
On
O
1.5 sec 3 light blinks
O
On
OFF button
3 sec
On
O
On
O
1.5 sec 3 light blinks
7 8
9
On
O
ON button
OFF button
4 sec
O
On
OFF button
Short press
On
O
On
O
ON button ON button
4 sec 4 sec
OFF button OFF button O
On
OFF button
Short press
10 11
12 13
On
O
CLICK
On
O
1. Place battery
Open the battery slot at the back of the ALKCT by sliding it down. Place the included 3V CR2477 battery
and close the battery slot. For more information on replacing and purchasing new batteries visit
trust.com/71115
2. LED indicator
Low battery: LED will blink 2x when a button is pushed
Confirm pair/unpair: LED will blink 5x
Successful arm/disarm: LED will light for 1.5 sec
Unsuccessful arm/disarm: LED will blink shortly 3x
3. Activate the pairing mode
Consult the manual of the Siren to activate the pairing mode. Put the ALKCT in pairing mode by first
pressing the ON and OFF button simultaneously for 4 sec (untill the LED of the ALKCT starts blinking).
4. Confirm pairing
After entering pairing mode press the ON button shortly to pair with the Siren. The LED indicator of the
Siren and ALKCT will be flashing 5 times to confirm that the pairing has been done successfully.
5. Arm the siren
To arm the siren press the ON button for 3 seconds on the ALKCT.
If the siren is armed successfully the LED of the ALKCT will light up for 1.5 sec.
If the siren is armed unsuccessfully the LED of the ALKCT will give 3 short light blinks.
Check the following points if the siren is armed unsuccessfully:
- Is the siren within range
- Are siren batteries low
- Are the remote batteries low
- Is another wireless device nearby
EN
6. Disarm the siren
To disarm the siren press the OFF button for 3 seconds on the ALKCT.
If the siren is disarmed successfully the LED of the ALKCT will light up for 1.5 sec.
If the siren is disarmed unsuccessfully the LED of the ALKCT will give 3 short light blinks.
Check the following points if the siren is disarmed unsuccessfully:
- Is the siren within range
- Are siren batteries low
- Are the remote batteries low
- Is another wireless device nearby
7. Activating the unpairing mode
Consult the manual of the Siren to activate the pairing mode. Put the ALKCT in pairing mode by first
pressing the ON and OFF button simultaneously for 4 sec (untill the LED of the ALKCT starts blinking).
8. Confirm unpairing
After entering pairing mode press the OFF button shortly to unpair with the Siren. The LED indicator of
the Siren and ALKCT will be flashing 5 times to confirm that the unpairing has been done successfully.
9. Delete ALKCT memory
To delete the memory of the ALKCT press the ON and OFF button simultaneously for 4 seconds (untill
the LED starts to blink) Release the buttons and press the ON and OFF buttons simultaneously again
for 4 seconds. (untill the LED starts to blink fast). Press the OFF button shortly to delete the memory of
the ALKCT. The LED will blink 5x to confirm the memory has been deleted.
10. Opening ALKCT casing (Optional, available on trust.com)
Open the casing by untightening the screws on the bottom of the case. The backplate can be pulled
o by lifting the screws.
EN
11. Mounting the casing
Mount the casing of the ALKCT on a flat surface and secure it with screws. (Mounting screws not
included)
12. Place ALKCT in casing
When the casing has been mounted and secured with screws place the ALKCT in the casing. To place
the ALKCT slide it in from top to bottom.
13. Close the casing
To close the casing put the frontplate on the backplate and push down till you hear a click. This means
the front plate has been locked on the backplate. Secure it with screwing the previously untightened
screws back on the bottom of the casing.
EN
EN
DE
DE
FR
FR
NL
NL
IT
IT
ES
ES
PT
PT
NO
NO
SV
SV
FI
FI
DA
DA
PL
PL
1. Podłącz lampę/urządzenie i umieść odbiornik
Najpierw sprawdź, czy lampa lub urządzenie jest włączone. Następnie podłącz lampę lub urządzenie
do odbiornika i włącz odbiornik do gniazda zasilania. Nie należy przekraczać maksymalnego
obciążenia: 1000 W.
CS
CS
SK
SK
HU
HU
RO
RO
BG
BG
1. Свържете лампата/устройството и сложете приемателя
Първо проверете дали лампата или устройството е включено. След това включете щепсела на
лампата или устройството в приемателя и включете приемателя в контакт. Не надвишавайте
максималната мощност: 1000 W.
EL
EL
TR
TR
RU
RU
SL
SL
HR
HR
UA
UA
AR
AR