Trust ALMST-2000 User Manual
Displayed below is the user manual for ALMST-2000 by Trust which is a product in the Smart Home Transmitters category. This manual has pages.
Related Manuals
www.trust.com
SECURITY PLUS-LINE
ALMST-2000
ALMST-2000 WIRELESS MAGNETIC SENSOR
USER MANUAL
MULTI LANGUAGE
Item 71113 Version 1.0
Visit www.trust.com
for the latest instructions
2
4
1
3
DELSET
DELSET
SET
1 sec
Red LED indicator
6
8
5
7
ON
DELSET
DEL
1 sec
9
10
DELSET
DELSET
DELSET
DEL DEL DEL
2 sec 3 sec Short press
1. Place batteries
Push with a sharp object on top of the magnetic sensor and pull o the backside. Insert two 1,5V AAA
Alkaline batteries in the slot. Observe the correct polarity of the batteries (place plus and minus on the
correct side).
2. LED indicator
The magnetic sensor has a LED indicator in the housing. The LED behaviour is as followed.
Low battery: LED will blink 3x every 6 sec
Confirm pair: LED will blink 5x
Confirm unpair: LED will blink 5x
3. Pair the ALMST
Consult the manual of the Siren to activate the learn mode. Send (while the learn mode of the Siren
is active) a pair-signal by pressing the SET button with a sharp object next to the battery slot of the
magnetic sensor. The LED indicator will flash 5x to confirm that the pairing has been done successfully.
4. Mount the ALMST
Place the magnetic sensor on the window or door and make sure that both points on the two parts
are in line with each other. Mark the top and bottom of both parts. After marking the positions remove
the sensor.
5. Remove backplate from the ALMST
Open the magnetic sensor by pushing with a sharp object on top of both parts and pull o the
backplate.
6. Fasten the ALMST
Screw or tape both backplates of the magnetic sensor on the window or door according to the made
markings. When securing the backplates make sure both parts are mounted with as little space
between as possible (max. 15mm).
EN
7. Close the ALMST
Place both parts of the magnetic sensor back on the mounted backplates. Again make sure both
points on the two parts are in line with each other.
8. Operation of the ALMST
ON-signal: Once the two parts are separated more than 15mm from each other, the sensor sends an
ON-signal to the Siren.
Note: After arming the ALSIR-2000 there is a 75 sec walk-out time. 4 sec after arming the alarm
windows and doors can be opened for max 1 min. After 75 sec the sensor is active. Tip: Arm the Siren
from the outside.
9. Unpair the ALMST
Consult the manual of the Siren to activate the learn mode. Send (while the learn mode of the Siren
is active) a disconnect-signal by pressing the DEL button with a sharp object next to the battery slot
of the magnetic sensor. The LED indicator will flash 5x to confirm that the unpairing has been done
successfully.
Note: When the sensor is not used unpair it from the Siren first before removing it.
10. Delete ALMST memory
To delete the memory of the ALMST press the DEL button for 2 seconds with a sharp object (untill the
LED starts to blink). Release the button and press the DEL button again for 3 seconds. (untill the LED
starts to blink fast). Press the DEL button shortly to delete the memory of the ALMDT. The LED will
blink 5x to confirm the memory has been deleted.
EN
DE
DE
FR
FR
NL
NL
IT
IT
ES
ES
PT
PT
NO
NO
SV
SV
FI
FI
DA
DA
PL
PL
1. Podłącz lampę/urządzenie i umieść odbiornik
Najpierw sprawdź, czy lampa lub urządzenie jest włączone. Następnie podłącz lampę lub urządzenie
do odbiornika i włącz odbiornik do gniazda zasilania. Nie należy przekraczać maksymalnego
obciążenia: 1000 W.
CS
CS
SK
SK
HU
HU
RO
RO
BG
BG
1. Свържете лампата/устройството и сложете приемателя
Първо проверете дали лампата или устройството е включено. След това включете щепсела на
лампата или устройството в приемателя и включете приемателя в контакт. Не надвишавайте
максималната мощност: 1000 W.
EL
EL
TR
TR
RU
RU
SL
SL
HR
HR
UA
UA
AR
AR