Important Safety Information
1 GXT5 Description
2 Installation
3 Operating the UPS
4 Operation and Display Panel
5 Maintenance
6 Troubleshooting
7 Specifications
- 7.1 Battery Run Times
Appendices
- Appendix A: Technical Support

Vertiv GXT5-EBC72VRT2U User Manual

Displayed below is the user manual for GXT5-EBC72VRT2U by Vertiv which is a product in the UPS Battery Cabinets category. This manual has pages.

Related Manuals

Vertiv Liebert RMKIT18-32 Sliding Rails Manual

Vertiv PS1000RT3-120 Manual

Vertiv PS1500RT3-120 Manual

Vertiv PS2200RT3-120 Manual

Vertiv Liebert PSI Manual

Vertiv Liebert APM Manual

Vertiv MXS5132-001 Manual

Vertiv MPHC1241 Manual

Liebert®

GXT5™ UPS

Installer/User Guide

120V, 500 VA to 3,000 VA

Vertiv | Liebert® GXT5™ Installer/User Guide

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent

section of this manual to see if the issue can be resolved by following outlined procedures.

Visit https://www.Vertiv.com/en-us/support/ for additional assistance.

The information contained in this document is subject to change

without notice and may not be suitable for all applications. While

every precaution has been taken to ensure the accuracy and

completeness of this document, Vertiv assumes no responsibility

and disclaims all liability for damages resulting from use of this

information or for any errors or omissions. Refer to other local

practices or building codes as applicable for the correct methods,

tools, and materials to be used in performing procedures not

specifically described in this document.

The products covered by this instruction manual are manufactured

and/or sold by Vertiv. This document is the property of Vertiv and

contains confidential and proprietary information owned by Vertiv.

Any copying, use or disclosure of it without the written permission

of Vertiv is strictly prohibited.

Names of companies and products are trademarks or registered

trademarks of the respective companies. Any questions regarding

usage of trademark names should be directed to the original

manufacturer.

TABLE OF CONTENTS

Important Safety Information 1

1 GXT5 Description 3

1.1 UPS Features and Available Models 3

1.2 Front Panels 4

1.3 Rear Panels 4

1.4 Battery Cabinet 7

1.5 Major Internal Components and Operating Principle 7

1.6 UPS States and Operating Modes 9

1.6.1 Normal Mode 9

1.6.2 Bypass Mode 10

1.6.3 Battery Mode 10

1.6.4 Frequency Converter Mode 10

1.6.5 ECO Mode 10

2 Installation 11

2.1 Unpacking and Inspection 11

2.2 Pre-installation Preparation 11

2.2.1 Installation Clearances 11

2.3 Installing the UPS 11

2.3.1 Tower Installation 12

2.3.2 Rack Installation 12

2.4 Installing External Battery Cabinets 12

2.5 Connecting AC Input Power 15

2.6 Connecting Loads 15

2.7 Communication Connections 15

2.7.1 Connecting IntelliSlot Communication 16

2.7.2 Connecting to the Dry-contact Port 16

2.7.3 Connecting a Remote Emergency Power-off (REPO) Switch 17

2.7.4 Connecting a USB Cable 18

2.7.5 Connecting CLI Communication Cables 18

2.7.6 Connecting Sensors to the Control Port 19

3 Operating the UPS 21

3.1 Silencingthe Audible Alarm 21

3.2 Starting-up the UPS 21

3.3 Transferring to Battery Mode 22

3.4 Transferring from Normal to Bypass Mode 22

3.5 Transferring from Bypass to Normal Mode 22

3.6 Shutting-down the UPS Completely 22

3.7 Remote Emergency Power-off (REPO) 22

4 Operation and Display Panel 23

4.1 LED Indicators 25

Vertiv | Liebert® GXT5™ Installer/User Guide | iii

4.2 LCD Menu and Screens 25

4.2.1 Start-up and Flow Screens 25

4.2.2 Main Menu 26

4.3 Editing Display and Operation Settings 41

4.3.1 Changing the Password 41

4.3.2 Selecting the Display Language 42

4.3.3 Setting the Date and Time 42

5 Maintenance 43

5.1 Replacing Batteries 43

5.2 Charging Batteries 45

5.3 Checking UPS Operation 46

5.4 Cleaning the UPS 46

6 Troubleshooting 47

6.1 Symptoms that Require Troubleshooting 47

6.2 Audible Alarm (Buzzer) 47

6.2.1 Faults 47

6.3 Troubleshooting UPS Issues 48

7 Specifications 49

7.1 Battery Run Times 54

Appendices 57

Appendix A: Technical Support 57

Vertiv | Liebert® GXT5™ Installer/User Guide | iv

IMPORTANT SAFETY INFORMATION

IMPORTANT! This manual contains important safety instructions that must be followed during the

installation and maintenance of the UPS and batteries. Read this manual thoroughly and the safety and

regulatory information, available at https://www.vertivco.com/ComplianceRegulatoryInfo, before

attempting to install, connect to supply, or operate this UPS.

Vertiv | Liebert® GXT5™ Installer/User Guide

This page intentionally left blank

1 GXT5 DESCRIPTION

The Liebert® GXT5 is a compact, online uninterruptible power system (UPS) that continuously conditions

and regulates its output voltage. The Liebert® GXT5 supplies microcomputers and other sensitive

equipment with clean sine-wave input power.

Upon generation, AC power is clean and stable. However, during transmission and distribution it is subject

to voltage sags, spikes, and complete failure that may interrupt computer operations, cause data loss, and

damage equipment.

The Liebert® GXT5 protects equipment from these disturbances. The Liebert® GXT5 continuously

charges its batteries from the utility power, enabling it to supply power to connected loads, even when the

mains fail.

1.1 UPS Features and Available Models

The GXT5 includes the following features. Table 1.1 below, lists the available models and power ratings.

•Enhanced load capacity with an output power factor of 1.

•Input power factor greater than 0.99

•Optional tower or rack installation to meet varying installation requirements.

•Adapts to areas with unstable power-mains supply via high-frequency double-conversion

topology structure, with high input-power factor, wide input-voltage range, and output

immune to grid interference.

•Full digital-control platform and hardware-design platform adapts to unstable mains supply

and load impact

•Programmable terminals with cascade protection protect key devices when load is heavy.

•Operation and display panel with model-specific color LCD offers simple configuration and

control of the UPS.

•ECO power-supply mode and smart-sleep mode help you save the maximum amount of energy.

MODEL NUMBER NOMINAL POWER RATING

GXT5-500LVRT2UXL 500VA/500W

GXT5-750LVRT2UXL 750VA/750W

GXT5-1000LVRT2UXL 1000VA/1000W

GXT5-1500LVRT2UXL 1500VA/1350W

GXT5-2000LVRT2UXL 2000VA/1800W

GXT5-3000LVRT2UXL 3000VA/2700W

Table 1.1 UPS Models and Power Ratings

1 GXT5 Description 3

1.2 Front Panels

The various GXT5 models have the same general appearance, with the main difference being the

receptacle types on the rear panel.

Figure 1.1 Front View

1.3 Rear Panels

The following figures detail the rear-panel features for each GXT5 model.

Figure 1.2 GXT5-500/750/1000/1500LVRT2UXL Rear Panel

ITEM DESCRIPTION

1 Liebert® IntelliSlot™ port

2 USB port

3 RS-485 port

4 External-battery connector

5 Non-programmable output receptacles, IEC-60906-1 15-A

6 Programmable output receptacles, IEC-60906-1 15-A

7 Input circuit breaker

8 Input-power plug and cable, IEC-60906-1 15-A

9 RS-232 port

10 Terminal-block communication connectors

Vertiv | Liebert® GXT5™ Installer/User Guide

Figure 1.3 GXT5-2000LVRT2UXL Rear Panel

ITEM DESCRIPTION

1 Liebert® IntelliSlot™ port

2 USB port

3 RS-485 port

4 External-battery connector

5 Non-programmable output receptacles, IEC-60906-1 20-A

6 Programmable output receptacles

7 Input circuit breaker

8 Input-power plug and cable, L5-20P

9 RS-232 port

10 Terminal-block communication connectors

11 Output-power plug and cable, L5-20R

1 GXT5 Description 5

Figure 1.4 GXT5-3000LVRT2UXL Rear Panel

ITEM DESCRIPTION

1 Liebert® IntelliSlot™ port

2 USB port

3 RS-485 port

4 External-battery connector

5 Non-programmable output receptacles, IEC-60906-1 20-A

6 Programmable output receptacles

7 Output circuit breakers

8 Input-power plug and cable, L5-30P

9 RS-232 port

10 Terminal-block communication connectors

11 Output-power plug and cable, L5-30R

12 Input circuit breaker

13 Cooling fan

Vertiv | Liebert® GXT5™ Installer/User Guide

1.4 Battery Cabinet

Optional battery cabinets are available for the UPS, and include a single battery-connector cable. Up to 10

battery cabinets may be connected in parallel to the UPS, and up to 6 can be detected using EBC-

detection. See External Battery Cabinet Specifications on page53, for the cabinet specifications. For

approximate battery run times with additional EBCs, see Battery Run Times on page54. See Installing

External Battery Cabinets on page12, to connect the cabinets.

Figure 1.5 Battery Cabinet

ITEM. DESCRIPTION

1 Battery connectors

2 Isolation breaker

1.5 Major Internal Components and Operating Principle

Figure 1.6 on the next page, shows the UPSoperating principle. Table 1.2 on page9, describes the

function of the major components in the UPS.

NOTE: Figure 1.6 on the next page, is one example of basic operation.

1 GXT5 Description 7

Figure 1.6 Basic Operating Principle Diagram

Vertiv | Liebert® GXT5™ Installer/User Guide

ITEM COMPONENT OPERATION/FUNCTION

Transient

Voltage Surge

Suppression

(TVSS) and

EMI/RFI Filters

Provide surge protection. Filter electromagnetic interference (EMI) and radio frequency interference

(RFI). Minimize surges or interference present in the utility power and protect devices connected on the

same branch as the UPS.

Rectifier/Power

Factor

Correction

(PFC) Circuit

In normaloperation, converts utility AC power to regulated DC power for use by the inverter while

ensuring that the wave shape of the input current used by the UPS is near ideal. Extracting this sine-wave

input current ensures efficient use of utility power and reduces reflected harmonic distortion making

cleaner power available to devices that are not protected by the UPS.

3 Batteries

Valve-regulated, non-spillable, lead-acid batteries.

NOTE: To maintain battery design life, operate the UPS in an ambient temperature of 59°F to 77°F

(15°C to 25°C).

4DC-to-DC

Converter

Raises the DC voltage from the battery to the optimum operating voltage for the inverter. This allows the

inverter to operate continuously at its optimum efficiency and voltage, thus increasing reliability.

5 Inverter

In normal operation, inverts the DC output of the PFC circuit into precise, regulated sine-wave AC power.

When utility power fails, the inverter receives DC power from the DC-to-DC converter. In either

operating mode, the UPS inverter remains on-line, generating clean, precise, regulated AC-output

power.

6Dynamic

Internal Bypass

In the unlikely event of UPS failure such as overload or over-temperature, automatically transfers the

connected load to bypass.

To manually transfer the connected load from inverter to bypass, see Transferring from Normal to

Bypass Mode on page22.

7 EMI/RFI Filters Filter electromagnetic interference (EMI) and radio frequency interference (RFI). Minimize interference

present in the utility power and protect devices connected on the same branch as the UPS.

8 Outlet group Programmable output receptacles.

9 Outlet group General output receptacles.

10 Outlet group General output receptacles on 2,000- and 3,000-VA models only.

Table 1.2 Major Components

1.6 UPS States and Operating Modes

NOTE: See LED Indicators on page25, for description of the run-indicator and alarm-indicator LEDs

mentioned in this section.

1.6.1 Normal Mode

When utility power is normal, Normal mode employs the rectifier and inverter to provide voltage- and

frequency-stabilized power to the load. The charger charges the battery in normal mode. On the front-

panel display, the run-indicator (green)is On, the alarm indicator is OFF, and the buzzer is silent.

1 GXT5 Description 9

1.6.2 Bypass Mode

Bypass mode supplies power to the load from the bypass source (utility power) if an overload or fault

occurs during normal operation. On the front-panel display, the run indicator (green) is On, the alarm

indicator (yellow)is On, and the buzzer beeps once each seconds. The LCD "Current" screen displays "On

Bypass."

NOTE: If utility power fails or if the utility voltage goes outside of the permissible range during bypass-

mode operation, the UPS shuts down and no output is supplied to the load.

1.6.3 Battery Mode

Battery mode supplies battery power to the load if utility power fails or if the utility voltage goes outside of

the permissible range. On the front-panel display, the run indicator (green) is On, the alarm indicator

(yellow)is On, and the buzzer beeps once each second. The LCD "Current" screen displays "On Battery."

NOTE: The batteries are fully-charged before shipment. However, transportation and storage

inevitably cause some loss of capacity. To ensure adequate back-up time, charge the batteries for at-

least 8 hours before first start-up.

NOTE: If utility power fails and the batteries are charged, you may cold-start the UPS in battery mode

and use battery power to extend system availability for a time.

NOTE: Powering-off the UPS when it is in battery mode results in loss of output power to the

connected load.

1.6.4 Frequency Converter Mode

All models of the GXT5 are capable of frequency conversion. Frequency Conversion Mode can be selected

using the configuration program. Allowable frequency operating modes include:

•Auto Sensing - 50 Hz or 60Hz – Bypass Enabled

•Auto Sensing - 50 Hz or 60Hz – Bypass Disabled

•Frequency Converter - 50 Hz – Bypass Disabled

•Frequency Converter - 60Hz – Bypass Disabled

NOTE: The default for all models of the Liebert® GXT5 is “Auto Sensing - 50 Hz or 60Hz – Bypass

Enabled.”

1.6.5 ECO Mode

The energy-saving ECO mode reduces power consumption by powering the load via bypass if the bypass

voltage is normal or by powering the load via the inverter when the bypass voltage is abnormal. You can

use ECOmode to power equipment that is not sensitive to power-grid quality to via bypass and reduce

power consumption.

NOTE: During Eco mode, if a bypass-failure or abnormal-bypass-voltage notification appears when the

output is not overloaded, the UPS will transfer to Normal Mode. However, if a notification showing

bypass failure or abnormal bypass voltage appears when the output is overloaded, the UPS will shut

down the bypass.

Vertiv | Liebert® GXT5™ Installer/User Guide

2 INSTALLATION

Do not start the UPS until after the installation is finished.

WARNING! Risk of electrical shock. Can cause equipment damage, injury and death. Before

beginning installation, verify that all external overcurrent protection devices are open (Off), and

that they are locked-out and tagged appropriately to prevent activation during the installation,

verify with a voltmeter that power is Off and wear appropriate, OSHA-approved personal

protective equipment (PPE) per NFPA 70E. Failure to comply can cause serious injury or death.

Before proceeding with installation, read all instructions. Follow all local codes.

2.1 Unpacking and Inspection

Unpack the UPS and conduct the following checks:

•Inspect the UPS for shipping damage. If any shipping damage is found, report it to the carrier

and your local Vertiv representative immediately.

•Check the accessories included against the packing list. If there is any discrepancy, contact

your local Vertiv representative immediately.

CAUTION: The UPS is heavy (see Specifications on page49, for the weight). Take proper

precautions when lifting or moving the unit.

2.2 Pre-installation Preparation

•Install the UPS indoors in a controlled environment, where it cannot be accidentally turned Off.

The installation environment should meet the specifications listed in Specifications on

page49.

•Place the UPS in an area of unrestricted air-flow around the unit, away from water, flammable

liquids, gases, corrosives, and conductive contaminants. Avoid direct sunlight

NOTE: Operating the UPS in temperatures above 77°F (25°C) reduces battery life.

2.2.1 Installation Clearances

Maintain at least 4in.(100mm) clearance in the front and rear of the UPS. Do not obstruct the air inlets on

the front panel and rear panel of the UPS. Blocking the air inlets reduces ventilation and heat dissipation,

shortening the service life of the unit.

2.3 Installing the UPS

The UPS may be installed as a tower or in a rack, depending on available space and use considerations.

Determine the type of installation and follow the appropriate instructions. See Tower Installation on the

next page or Rack Installation on the next page.

NOTE: When installing the UPS or making input and output connections, comply with all relevant

safety codes and standards

2 Installation 11

2.3.1 Tower Installation

To install the UPS as a tower:

1. Take the support bases out of the accessories box.

Figure 2.1 Support bases

NO. DESCRIPTION

1 Support bases

Spacers with connectors

NOTE: Three spacers are shown here. However, the number of spacers varies depending on your UPS

model and the number of battery cabinets in your system.

2. If optional, Liebert® external battery cabinets will be connected, take out the spacers shipped

with the battery cabinet.

3. Connect the spacers and the support bases as shown in Figure 2.1 above. Each GXT5 requires

2support bases, one in the front and one in the rear.

4. Place the GXT5 and any battery cabinets on the 2support bases.

2.3.2 Rack Installation

When installed in a rack enclosure, the GXT5 UPS and external battery cabinets (EBC) must be supported

by a shelf or rack-mount rails. Because different rack-mount options install differently, refer to the

installation instructions provided with the rack-mount kit.

CAUTION: The GXT5 is heavy. The UPS must be installed as near the bottom of a rack as

possible. If placed too high, it can make the rack top-heavy and prone to tipping over. For unit

weights, see Specifications on page49.

2.4 Installing External Battery Cabinets

Optional, external battery cabinets (EBC) may be connected in parallel to the UPS to provide additional

battery run time. For approximate battery run times with additional EBCs, see Battery Run Times on

page54.

External battery cabinets are placed on one side of the UPS in a tower configuration or stacked beneath

the UPS in a rack configuration. Up to 10 EBCs may be connected to the UPS, and up to 6 may be

detected using EBC-detection.

Vertiv | Liebert® GXT5™ Installer/User Guide

WARNING! Risk of electric shock. Can cause injury or death. Disconnect all local and remote

electric power supplies before working with the UPS. Ensure that the unit is shut down and

power has been disconnected before beginning any maintenance.

CAUTION: The external battery cabinet(s) are heavy, see Table 7.3 on page53. Take proper

precautions when lifting them.

To install the EBC(s):

1. Inspect the EBC for freight damage. Report damage to the carrier and your local dealer or

Vertiv representative.

2. For tower installation:

•An additional set of support-base extensions ships with each EBC.

•See the steps in Tower Installation on the previous page, to connect the support

extenders and install the bases.

– or –

For rack installation:

•Rack-mount hardware ships with the EBC.

•Refer to the instructions included with the rack-mount kit to install.

NOTE: Optional slide rails and securing hardware are sold separately. Please contact your Vertiv

representative for options and Vertiv Technical Support for assistance.

3. Verify that the EBC breaker is in the "Off" position.

4. Connect the supplied EBC cable(s) to the rear of the cabinet, then to the rear of the UPS, see

Figure 2.2 on the next page.

5. Turn the EBC breaker to the "On" position.

6. Verify the circuit breaker on the EBC is in the "On" position.

The additional back-up run time is enabled.

NOTE: When removing an EBC, turn off the circuit breaker on the rear of the cabinet before

disconnecting the cable.

NOTE: If shipping or storing the UPS for an extended time, disconnect the EBC(s) minimize stand-by

current drain on the batteries and help maintain design life.

2 Installation 13

Figure 2.2 EBCs connected to the UPS

ITEM DESCRIPTION

1 EBC-detection dry-contact port (See Table 2.2 on page17, for details.)

2 EBC connector

3 EBC-detection port

4 External battery cabinet

5 External battery cabinet

Vertiv | Liebert® GXT5™ Installer/User Guide

2.5 Connecting AC Input Power

Ensure that all the loads are turned Off. Prepare an input power supply that is properly protected by a

circuit breaker in accordance with national and local electrical codes. The wall receptacle must be

grounded. We recommend installing an upstream circuit breaker of the same series as the input circuit

breaker of the GXT5.

Table 2.1 below, lists the specifications of the input circuit breaker on the rear panel by UPS model

MODEL RATED CIRCUIT BREAKER

GXT5-500LVRT2UXL 12A

GXT5-750LVRT2UXL 12A

GXT5-1000LVRT2UXL 12A

GXT5-1500LVRT2UXL 15A

GXT5-2000LVRT2UXL 20A

GXT5-3000LVRT2UXL 30A

Table 2.1 Input circuit breaker

specifications

To connect AC-input power, plug the input plug of the UPS into the input-power connection.

NOTE: If the input plug will serve as the disconnecting device, the wall socket/outlet must be near the

UPS and must be easily accessible, per the National Electric Code/NFPA 70 requirements.

2.6 Connecting Loads

500-VA to 1500-VA models have five groups of outlets:

•One group is not programmable (always On).

•Four groups are controlled with programmed responses or an SNMP network.

2000-VA and 3000-VA models have six groups of outlets:

•Two groups are not programmable (always On).

•Four groups are controlled with programmed responses or an SNMP network.

NOTE: When connecting load, verify that the equipment is plugged into the appropriate outlets if any

of the outlets will be controlled.

NOTE: Do not overload any output receptacle. Output cable length should not exceed 10m (32.8ft).

To connect equipment, plug equipment into the appropriate output receptacles on the rear of the UPS,

see the appropriate figure for your model in Rear Panels on page4.

2.7 Communication Connections

The UPS offers several communication interfaces and ports.

NOTE: We recommend that signal-cable lengths be less than 10ft(3m), and are kept away from power

cabling.

2 Installation 15

2.7.1 Connecting IntelliSlot Communication

The IntelliSlot ports accepts two optional cards:

The Liebert® IntelliSlot™ Relay card (IS-RELAY) card provides dry-contact relay output for custom-wired

applications.

The Liebert® IntelliSlot™ Unity card (RDU101) provides SNMP monitoring of the UPS across the network

and/or building management system and lets you monitor external temperature, humidity and contact-

closure inputs using external sensors.

See the appropriate figure for your model in Rear Panels on page4, for the location of the card port.

To install an IntelliSlot Card:

1. Remove the screws from the slot cover plate and remove the plate.

2. Insert the card into the slot, and secure with the screws that held the cover plate.

To make connections to the card, refer to the Installer/User Guide for the appropriate IntelliSlot card

available at www.Vertiv.com.

2.7.2 Connecting to the Dry-contact Port

The UPS includes a dry-contact port. See the appropriate figure for your model in Rear Panels on page4,

for the location of the port. Figure 2.3 below, shows the ports and Table 2.2 on the facing page,

describes each port.

The I/O dry contact port capacity is 125Vdc, 0.5A; 30Vdc, 1A

Figure 2.3 Dry-contact Port and Pin Layout

NOTE: Pins 7 and 8 are shorted before delivery.

NOTE: The emergency power-off (EPO) action of the UPS closes the rectifier, inverter and static

bypass, but it cannot disconnect the UPS mains input inside. To completely disconnect the UPS,

disconnect the upstream input circuit breaker when generating the EPO. For details on

REPOconnection and operation, see Connecting a Remote Emergency Power-off (REPO) Switch on

the facing page.

Vertiv | Liebert® GXT5™ Installer/User Guide

PORT

NO.

PORT

NAME

NO. PIN NAME DESCRIPTION

1 Input 1

Disable/Battery mode

shutdown/Any mode

shutdown (Remote Comms

Shutdown)

Default: Disable, can be set via the LCD settings page. User can choose

dry contact as NO/NC. when NO, Pin 1 and Pin 2 are shorted, the

function is active. when NC, Pin 1 and Pin 2 are open, the function is

active.

2 Signal Ground Signal Ground

2 Input 2

Disable/Battery mode

shutdown/Any mode

shutdown (Remote Comms

Shutdown)

Default: Disable, can be set via the LCD settings page. User can choose

dry contact as NO/NC. when NO, Pin 1 and Pin 2 are shorted, the

function is active. when NC, Pin 1 and Pin 2 are open, the function is

active.

4 Signal Ground Signal Ground

3Battery

Detection

5 EBC Detection

Default: Normally-Open (NO), automatically detects number of external-

battery cabinets when pins 5 and 6 are connected to the detection port,

see Installing External Battery Cabinets on page12.

6 EBC Detection

Default: Normally-Open (NO), automatically detects number of external-

battery cabinets when pins 5 and 6 are connected to the detection port,

see Installing External Battery Cabinets on page12.

REPO REPO

Input

7 +5V REPO power supply, 5-Vdc 100-mA

8 REPO Coil -NC

NC, activated when Pin 7 and Pin 8 is open

NOTE: For details on REPOconnection and operation, see

Connecting a Remote Emergency Power-off (REPO) Switch below.

5 Output 5

9Low Battery/Onbattery/

Onbypass/UPSfault

Default: Low battery, can be set via the LCD settings page. When the

system has afault, short Pin 9 and Pin 10

10 Signal Ground Signal Ground

6 Output 6

11 Low Battery/Onbattery/

Onbypass/UPSfault

Default: UPS fault, can be set via the LCD settings page. When the

system has afault, short Pin 11 and Pin 12

12 Signal Ground Signal Ground

Table 2.2 Dry-contact Connection and Pin-out Descriptions

2.7.3 Connecting a Remote Emergency Power-off (REPO) Switch

The UPS includes an EPO connection in the dry-contact port. See the appropriate figure for your model in

Rear Panels on page4, for the location of the port.

UPS ships with a REPO jumper installed, allowing the UPS to operate as a normally-closed switch system

(fail-safe). Opening the circuit disables the UPS. To connect a REPOswitch that opens the circuit to shut

down the rectifier and inverter and power-off the UPS, use a cable from the remote switch to plug into the

REPO-port on the UPS.

In normal conditions, the REPO switch cannot cut off the UPS input power. When the REPO switch trips,

the UPS generates an alarm and immediately cuts-off output power. When the emergency condition is

resolved, the UPS will not return to normal operation until you reset the REPO switch and manually power-

on the UPS.

2 Installation 17

To make the cable for the REPO connection:

Figure 2.4 below, shows the cable required to make the connection. We recommend using 18AWG to

22AWG (0.82mm2to 0.33mm2) copper-core cable.

1. Remove the insulation from the end of two cables.

2. Insert the stripped end into the plug terminals 1 and 2 respectively, then press down the

terminals. Make sure that the cables are secure in the plug to prevent failure because of loose

contact.

To connect a UPS to the REPO switch

CAUTION: To maintain safety (SELV) barriers and electromagnetic compatibility, signal cables

should be shielded and run separately from power cables.

1. Connect one end of the cable to the remote switch, see Figure 2.4 below.

2. Remove the factory-installed jumper from pins 7 and 8 of the dry-contact port on the UPS

3. Connect the plug to pins 7 and 8.

Figure 2.4 Cable/Plug for Connecting REPOswitch to UPS REPO port

ITEM DESCRIPTION

1 Terminal 1

2 Terminal 2

3 Plug (connects to REPO port on UPS)

4 REPO switch

2.7.4 Connecting a USB Cable

The UPS includes a USB connector. See the appropriate figure for your model in Rear Panels on page4,

for the location of the port.

The standard, B-type USB port connects the UPS to a network server or other computer system.

The USB port supports HID/CDC protocol. The CDC protocol is reserved for service software.

2.7.5 Connecting CLI Communication Cables

The UPS supports the Vertiv command-line interface for operation with ACS and other third-party

monitoring protocols. The RJ-45 port is used for CLI connection. See the appropriate figure for your model

in Rear Panels on page4, for the location of the port. The pin-out, described in Table 2.3 on the facing

page, is consistent with the ACS pin-out.

Vertiv | Liebert® GXT5™ Installer/User Guide

PIN SIGNAL DIRECTION

1 NC —

2 NC —

3 TXD O

4 GND —

5 NC —

6 RXD |

7 NC —

8 NC —

Table 2.3 RJ-45 Port Pin-out

2.7.6 Connecting Sensors to the Control Port

The UPS supports the Vertiv temperature and temperature/humidity sensors. The RJ-45 port is used for

sensor connection. See the appropriate figure for your model in Rear Panels on page4, for the location of

the port.

When connected, the sensor address must be 1to20.

The GXT5 supports two sensors:

•Liebert® IRM-S01T

•Liebert® IRM-S02TH

2 Installation 19

Vertiv | Liebert® GXT5™ Installer/User Guide

This page intentionally left blank

3 OPERATING THE UPS

WARNING! Risk of electric shock. Can cause injury or death. Hazardous mains and/or battery

voltage exists behind the protective cover No user accessible parts are located behind the

protective covers that require a tool for removal. Only qualified service personnel are

authorized to remove such covers. If maintenance for rack is needed, notice that the neutral

line is live.

3.1 Silencingthe Audible Alarm

The audible alarm may sound during UPS operation. To silence the alarm, press and hold the ESC button

for 2seconds. The button is located on the front-panel display, see Operation and Display Panel on

page23.

3.2 Starting-up the UPS

IMPORTANT! Do not start the UPS until after the installation is finished, the system is commissioned

by an authorized engineer, and the external input circuit breakers are closed.

CAUTION: Starting the UPS applies mains/utility power to the output terminals. Make sure that

the load power is safe and ready to accept power. If the load is not ready, isolate the load with

the output terminal.

The UPS starts in Normal Mode.

To start the UPS:

1. If included on your UPS model, make sure the maintenance-bypass switch is in the open “OFF”

position and that the guard is secured in place.

2. Ensure that the REPO connector on the rear of the unit has a jumper between pins 7-8 or that

it is properly wired to an Emergency Power- Off circuit (normally closed).

3. Make sure the breaker supplying power to the UPS is closed, and close the input breaker on

the rear of the UPS.

4. If included on your UPS model, close the bypass breaker on the rear of the UPS

5. Close all output breakers on the rear of the UPS (or in an external panel board, if used).

6. Power-on the UPS by pressing and holding the power button on the operation and display

panel until the confirmation dialog appears. Use the Up/ Down arrows to select YES, then press

Enter.

7. If this is the first-time start-up of the UPS, the Start-up Guidance wizard opens to set the basic

parameters of the UPS. Follow the prompts.

For detailed description of UPS display functions and settings, see Operation and Display Panel

on page23.

3 Operating the UPS 21

3.3 Transferring to Battery Mode

The UPS operates in Normal mode unless the mains/utility power fails or it is performing a battery self test,

then it automatically transfers to Battery mode for the back-up time available or the mains/utility power is

restored. Once input power is restored, the UPS returns to Normal mode.

NOTE: Battery back-up run times are listed in Battery Run Times on page54.

3.4 Transferring from Normal to Bypass Mode

Press and hold the power button for 2 seconds.

•If the bypass power is within normal operating range, the option to continue to Bypass mode or

turn-off the UPS displays:

a. Use the arrow buttons to select To the Bypass, and press Enter.

b. Use the arrow buttons to select No or Yes, then press Enter to confirm.

•If the bypass power is outside normal operating range, do not transfer to Bypass mode.

3.5 Transferring from Bypass to Normal Mode

Press and hold the power button for 2 seconds.

•If the UPS is operating normally, without faults, the option to continue to turn-on or turn-off the

UPS displays:

a. Use the arrow buttons to select Turn on UPS, and press Enter.

b. Use the arrow buttons to select No or Yes, then press Enter to confirm.

NOTE: The UPS automatically switches back to normal mode after an "overheated" or "overloaded"

fault is cleared and normal power is restored.

3.6 Shutting-down the UPS Completely

WARNING! Risk of electric shock. Can cause injury or death. Disconnect all local and remote

electric power supplies before working with the UPS. Ensure that the unit is shut down and

power has been disconnected before beginning any maintenance.

Transfer to Bypass mode, see Transferring from Normal to Bypass Mode above. Then, if power to the load

is not needed, open the main-input circuit breaker.

3.7 Remote Emergency Power-off (REPO)

REPO turns off the UPS in emergency conditions such as fire or flood. When an emergency occurs, the

REPO switch turns off the rectifier and inverter and stops powering the load immediately. The battery

stops charging and discharging.

To manually power-off in an emergency, disconnect the terminal connecting the REPO port on the rear of

the UPS.

If mains/utility power is present, the UPS control circuit remains active even though output power is

disabled. To remove all mains/utility power, disconnect the external main-input MCB.

Vertiv | Liebert® GXT5™ Installer/User Guide

4 OPERATION AND DISPLAY PANEL

NOTE: The UPS has a gravity-sensor function that automatically rotates the LCD display depending on

tower or rack installation. See Display orientation on page32.

The operation/display panel includes LED indicators, function keys, and an LCDinterface to configure

and control UPS operation.

Figure 4.1 UPS Front-panel Display

ITEM DESCRIPTION

1 Run indicator LED, see LED Indicators on page25.

2 Alarm indicator LED, see LED Indicators on page25.

3 Power button, see Table 4.1 on the next page.

4 Menu keys, see Table 4.1 on the next page.

5 LCD panel.

4 Operation and Display Panel 23

BUTTON FUNCTION DESCRIPTION

Enter Confirm or enter selection.

Up Move to previous page, increase value, move left.

Down Move to next page, decrease value, move right.

Escape Go back.

Power Power-on the UPS, power-off the UPS, transfer to Bypass Mode.

Table 4.1 Display-panel Button Functions and Descriptions

NOTE: While the UPS is operating, the LCD will dim and display a screen saver if there is no active alarm

or user interaction for two minutes, see Figure 4.2 below. If an alarm or fault occurs or if any button is

pressed, the UPS-flow screen displays.

Figure 4.2 LCD Screen Saver

Vertiv | Liebert® GXT5™ Installer/User Guide

4.1 LED Indicators

The LEDs on the front-panel display indicate operation and alarm statuses of the UPS.

NOTE: When an alarm is indicated, an alarm message is logged. on page36, describes the alarm

messages you may see. When a fault is indicated, front-panel display list the fault, which are described

in Table 6.2 on page47.

INDICATOR LED COLOR LED STATE INDICATES:

Run indicator Green

On UPS has output

Blinking Inverter is starting

Off UPS has no output

Alarm indicator

Yellow On Alarm occurs

Red On Fault occurs

None Off No alarm, no fault

Table 4.2 LED Functions

4.2 LCD Menu and Screens

The menu-driven LCD user interface lets you browse the UPS status, view operating parameters,

customize settings, control operation, and view alarm/event history. Use the function keys to navigate

through the menu, and view statuses or select settings in the screens.

4.2.1 Start-up and Flow Screens

At start-up, the UPS executes a system test and displays the Vertiv logo screen for about 10 seconds,

shown in Figure 4.1 on page23. After the test completes, an overview screen shows status information,

the active (green) power path, and the non-working power path (gray).

NOTE: Figure 4.3 below, is an example flow screen and does not reflect the actual values that you may

see on your unit.

Figure 4.3 UPS Flow Screen

4 Operation and Display Panel 25

4.2.2 Main Menu

To access the main menu, press Enter while at the flow screen. Table 4.3 below, describes the menu

options, and Figure 4.4 below, describes the display.

Use the arrow buttons to select the sub-menu options, and press Enter to open the sub menu. Press ESC

to return to the flow.

SUB MENU DESCRIPTION

Status Voltage, current, frequency, and parameters for UPS components, see Status Screen on the facing page.

Settings Display and system parameter settings, see Settings Submenu on page30.

Control UPS controls, see Control Screen on page35.

Log Current alarms and event history, see Log Screen on page36.

About Product and network information, see About Screen on page40.

Maintenance Service-only, service-password protected page for use only by Vertiv service representatives.

Table 4.3 Menu Options

Figure 4.4 Main Menu

ITEM DESCRIPTION

1 ECO-mode indicator

2 Programmable-outlet indicator

3 Ambient temperature and humidity. Only displays when sensors are connected.

4 Date and time

Vertiv | Liebert® GXT5™ Installer/User Guide

Status Screen

The status screen displays voltages, currents, frequencies, and parameters on individual tabs for input,

bypass, battery, output, and load status.

To view the UPS status information:

1. At the main menu, select the Status icon, and press Enter.

2. Use the arrow buttons to move the cursor left/right and select a tab, then press Enter to

display the status information for the selected tab.

Figure 4.5 Status-screen tabs

ITEM DESCRIPTION

1 Screen tabs with Input tab selected.

NOTE: Multiple phases are shown in multiple columns. For example, a unit with 3-phase input will

display 3 columns of status data.

Input statuses

L-N voltage(V)

Line-neutral voltage of input power.

L-N current(A)

Line-neutral current of input power.

Frequency (Hz)

Frequency of input of input power.

Power factor

Power factor of the input power.

4 Operation and Display Panel 27

Energy (kWh)

Input power.

Input black count

Count of input voltage lost.

Input brown count

Count of PFC overload to battery.

Bypass status options

L-N voltage(V)

Line-neutral voltage of bypass power.

Frequency (Hz)

Frequency of bypass power.

Battery status options

Battery status

Current battery state: charging, discharging, or fully-charged.

Battery voltage (V)

Voltage of battery power.

Battery current (A)

Current of battery power.

Backup time(Min)

Amount of back-up time remaining for battery.

Remaining capacity(%)

Percent of capacity remaining for battery.

Discharge count

Number of discharges for the battery module.

Total discharge time(Min)

Number of minutes until battery is fully discharged.

Batt running time(Day)

Number of days the batteries have been in operation.

Battery replacement time

Date of last time battery was replaced.

Vertiv | Liebert® GXT5™ Installer/User Guide

External battery cabinet group No.

Number of external battery cabinets connected.

Battery average temp(°C)

Average temperature of the battery.

Battery highest temp(°C)

Highest temperature battery has reached.

Battery lowest temp(°C)

Lowest temperature battery has reached.

Output status options

L-N voltage(V)

Line-neutral voltage of output power.

L-N current(A)

Line-neutral current of output power.

Frequency (Hz)

Frequency of output power.

Energy (kWh)

Output power

Load status options

Sout(kVA)

Apparent output power.

Pout(kVA)

Active output power.

Power factor

Power factor of output power.

Load percent(%)

Percentage of recent power rated to output power.

4 Operation and Display Panel 29

Settings Submenu

The settings screen consists of tabs that list UPS settings for configuration and adjusting parameters

with tabs for:

•Output

•Battery

•Monitor

•System

NOTE: Do not change parameter settings or reset to factory defaults when powering-off the UPS.

To modify UPSsettings:

1. At the main menu, select the Settings icon, and press Enter.

NOTE: To adjust the settings, you must enter a password. See Editing Display and Operation Settings

on page41, for details on entering the password and editing the setting parameters.

2. Use the arrow buttons to move the cursor left/right and select a tab, then press Enter to

display the parameter list for the selected tab.

Output parameter options

Voltage selection

Selects the default output voltage.

Startup on bypass

Whenenabled, the UPS starts in Bypass mode then transfers to Normal mode. When disabled, the

UPS starts in Normal mode.

Frequency selection

Selects the frequency of the output. Options are:

•Auto, Bypass enabled = Automatically detects frequency of utility/mains power and sets the

nominal frequency to match and bypass mode is enabled. Typical operating mode.

•Auto, Bypass disabled = Automatically detects frequency of utility/mains power and sets the

nominal frequency to match and bypass mode is disabled.

•Frequency converter 50Hz = Bypass mode is disabled and the UPSprovides 50-Hz output

from any qualified utility/mains power.

•Frequency converter 60Hz = Bypass mode is disabled and the UPSprovides 60-Hz output

from any qualified utility/mains power.

Bypass voltage upper limit

Percentage that the input voltage may be above the selected output voltage setting and remain in

Bypass mode.

Vertiv | Liebert® GXT5™ Installer/User Guide

Bypass voltage lower limit

Percentage that the input voltage may be below the selected output voltage setting and remain in

Bypass mode.

Run mode

Selects Normal or ECO operation for the UPS. Options are:

•Normal = Connected load is always powered through the UPS inverter. ECO mode is disabled.

•ECO mode = ECOmode is enabled. The UPS inverter is bypassed, and the connected load is

ECOvoltage range

Percentage that the input voltage may be above or below the selected output voltage setting and

remain in ECO mode.

ECOfrequency range

Amount that the input frequency (Hz)may be above or below the selected frequency setting and

remain in ECO mode.

ECO requalification time

To ensure the stability of the utility/mains power, this is the length of time that the UPS requires

after the input-power voltage and frequency tolerances are met before switching to ECO-mode

operation.

Battery parameter options

External battery AH

Sets the Amp-hour.

External battery cabinet group No.

Sets the number of external battery cabinets.

Low battery time

Sounds an alarm when the selected amount of time remaining for the UPS to operate in Battery

mode is met.

Battery periodic test enable

Enables/Disables automatic battery self test.

Batt. note duration (months)

Sets the duration of the notice to replace the batteries.

Dischg protect time

Sets the discharge protection time.

Equal charge enable

Enable/Disabels equal-charge mode.

4 Operation and Display Panel 31

Max chg curr

Sets the maximum charge current.

Temp compensation

Enables/Disables temperature compensation.

Replace battery

Activates newly-installed battery packs after replacement.

Monitor settings options

Language

Selects the language of the display, see Selecting the Display Language on page42. Options are:

•English

•French

•Portuguese

•Spanish

•Chinese

•German

•Japanese

•Russian

Date

Selects the current date for the UPS display, YYYY-MM-DD.

Time

Select the current time for the UPSdisplay, HH:MM:SS.

Display orientation

Selects the orientation of the display for use in rack or tower configuration. Options are:

•Auto-rotate = Automatically rotates based on the detected orientation of the UPS.

•Horizontal

•Vertical

Audible alarm

Enables/Disables the audible alarm of the UPS.

Change settings password

Opens the dialog to change the password used to access and update the UPS parameter settings,

see Changing the Password on page41.

Vertiv | Liebert® GXT5™ Installer/User Guide

System parameter options

Auto restart

Enables/Disables automatic restart of the UPS when input power is restored after a complete shut-

down of the UPS system.

Auto restart delay

Length of time to elapse before an automatic restart after input power is restored.

Guaranteed shutdown

Enables/Disables continued shutdown of the UPS system after the Low Battery alarm threshold is

reached, even if input power is restored during this time.

Start with no battery

Enables/Disables UPS start-up when batteries are fully depleted.

Remote control

Enables/Disables remote control of the UPS.

Any mode shutdown auto restart enable

Enables/Disables any-mode shut-down auto-restart function.

Output contact NO/NC

Selects the state of the dry-contact output, normally-open or normally-closed.

Input contact NO/NC

Selects the state of the dry-contact input, normally-open or normally-closed.

Dry contact 5 (Output)

Selects the output of dry-contact 5. Options are:

•Low battery

•On bypass

•On battery

•UPS fault

Dry contact 6 (Output)

Selects the output of dry-contact 6. Options are:

•Low battery

•On bypass

•On battery

•UPS fault

4 Operation and Display Panel 33

Dry contact 1 (Input)

Selects the input of dry-contact 1. Options are:

•Disable

•Battery mode shutdown

•Any mode shutdown

Dry contact 2 (Input)

Selects the input of dry-contact 2. Options are:

•Disable

•Battery mode shutdown

•Any mode shutdown

Sleep mode

Enables/Disables sleep mode.

ITsystem compatibility

Enables/Disables the neutral back-feed relay on battery mode.

Outlet parameter options

Apply the same settings as Outlet1

Applies the settings for another outlet to this outlet. This lets you set the parameters for a single

outlet and apply identical settings to multiple outlets at once.

Turn on outlet

Turns-on the outlet.

Turn on delay

Length of time to elapse before outlet turns on after UPS start-up.

Turn off when UPS overload on battery

Enables/Disables turning-off the outlet if the UPS is overloaded.

Outlet settings based on discharging time

Threshold of turning off the outlet

Length of time that the batteries discharge before turning off the outlet.

Turn on when power returns for

Length of time to elapse after input power returns before turning on the outlet.

Vertiv | Liebert® GXT5™ Installer/User Guide

Outlet settings based on backup time

Threshold of turning off the outlet

Amount of back-up time remaining to turn off the outlet.

Turn on when power returns for

Length of time to elapse after input power returns before turning on the outlet.

Outlet settings based on capacity

Threshold of turning off the outlet

Percent capacity remaining to turn off the outlet.

Turn on when power returns for

Length of time to elapse after input power returns before turning on the outlet.

Control Screen

The Control screen offers UPS-control options.

To adjust the UPS controls:

1. At the main menu, select the Control icon, and press Enter.

2. Use the arrow buttons to move the cursor to the option, then press Enter to selected the

control.

Figure 4.6 Control Screen

Control options

Turn on/off/to bypass

Opens the dialog to change operating modes, see Operating the UPS on page21.

4 Operation and Display Panel 35

Mute/Unmute audible alarm

Silences or un-silences the audible alarm, see Silencingthe Audible Alarm on page21.

Start/Stop battery manual test

Runs the battery self test.

Clear faults

Clears displayed faults after the issue causing the fault is resolved, see Table 6.2 on page47, for a

description of the faults.

Reset power statistics

Resets to zero the values tracked to calculate the Efficiency graph, see About Screen on page40.

Log Screen

The Log Screen offers tabs that list the current alarms and the alarm/event history. Table 4.4 below,

describes the alarm messages you may see in the logs.

To view the logs:

1. At the main menu, select the Log icon, and press Enter.

2. Use the arrow buttons to move the cursor left/right and select a tab, then press Enter to

display the log for the selected tab.

Figure 4.7 Current and History Log Tabs

MESSAGE DESCRIPTION

Aux. power fault The auxiliary power output voltage exceeds the normal range

Battery cabinet

connect

abnormal

An incorrect number of external battery cabinets are connected to the UPS.

Battery EOD Battery end of discharge.

Battery low

pre-warning

This alarm occurs when the battery reaches the EOD. After the pre-warning, the battery capacity allows two

minutes discharge at full load. The user can set the time ranging from 2 min～30 min, (2 min by default). Please

shut down the load timely

Table 4.4 Alarm Messages

Vertiv | Liebert® GXT5™ Installer/User Guide

MESSAGE DESCRIPTION

Battery mode The UPS is on battery, and the inverter starts

Battery

overtemp

Battery ambient temperature too high. Check that the battery ambient temperature is higher than setting value

40 ~ 60℃(default: 50℃)

Battery

replacement

timeout

The alarm will appear when the time (Battery replaced time adds the noted time of battery replacement) later than

the current system time. When the users set the noted time of battery replacement as disabled, the alarm will not

appear.

Battery test fail The battery low voltage is detected when the battery has manual or periodical self-test. Battery replacement is

recommended

Battery test

started The battery periodic self-test and manual self-test started

Battery test

stopped The battery periodic self-test or manual self-test finished

Battery to utility

transition The UPS is powered by the mains instead of the battery

Battery voltage

abnormal

When battery is connected, the system checks that the battery voltage exceeds the normal setting range. Check

that the battery terminal voltage exceeds the normalrange

Bypass

abnormal

Maybe caused by bypass voltage and frequency outside of range, bypass power-off and incorrect bypass cables

connection.

1. Check that the bypass voltage and frequency are within the setting range.

2. Check the bypass cables connection

Bypass

abnormal in

ECO mode

ayb e caused by ECO bypass voltage and frequency outside of range, ECO bypass power-off, and incorrect ECO

bypass cables connection. Check that the ECO bypass voltage and frequency are within the setting range.

Bypass mode The UPS is on bypass

Bypass

overcurrent The bypass current exceeds the rated value.

Charger fault The charger output voltage is abnormal, and the charger will be off .

Communication

fail Internal communication is abnormal, please check the communication cables are connected correctly or not.

DC bus

abnormal

The inverter is off when DC bus voltage is faulty. The load will transfer to bypass if the bypass is available because

the bus voltage exceeds the range.

DC/DC fault The discharger is faulty, because the bus voltage exceeds the range when discharger starts or soft starts.

EOD turn off The inverter is off due to EOD. Check the mains power-off state and recover the mains in time

Fan fault At least one fan is faulty. Check that the fan is blocked or the cables connection is loosened

Faults cleared The faults have been cleared using the Settings > Controls > Clear faults option.

Guaranteed

shutdown Under forced EOD mode, the battery discharging finished, then system shuts down

Input abnormal The rectifier and charger are off due to the mains voltage and frequency exceeding normal range. Check that the

rectifier input phase voltage and frequency exceed the normal range or that the mains has power-off

Input ground Check that the PEline is well connected and that the alarm can be cleared at the display.

Table 4.4 Alarm Messages (continued)

4 Operation and Display Panel 37

MESSAGE DESCRIPTION

lost

Input phase

reversed the input live line and N line are connected incorrect

Insufficient

capacity to

start

The UPS is on bypass，UPS get the command of start, the system load capacity is larger than 105% rated . the

prompt will appear

Inverter fault The inverter is off when the inverter output voltage and current exceed the setting range. If bypass is available, the

UPS will transfer to bypass mode, otherwise the system will power off

Inverter

overload

Inverter load capacity is larger than the rated value, overload delay time is up, inverter shuts down. If bypass is

available, the system will transfer to the bypass mode, otherwise the output is failure. Check that the actual inverter

load capacity, if overloaded, just reduce the load capacity, and the system will transfer to the inverter mode after

five seconds with alarm cleared

Load off due to

output short The inverter short circuit or the bypass short circuit. Please check it

Load off due to

shutdown on

battery

Shutdown in battery mode

Manual power-

on Set power-on via LCD panel

Manual

shutdown Set shutdown via LCD panel

Manual shut off Displayed when the user shuts-down UPS output.

No battery Check the battery and battery cables connection

Operating on

inverter The UPS output state is on inverter

Output disabled The system is in standby state, and the dry contact shutdown is enabled. Check whether the shutdown dry

contact is enabled or not

Output off due

to bypass

abnormal

The bypass is abnormal, and the bypass is in stand-by mode. Check that the bypass input is normal

Output off due

to overload &

bypass

abnormal

The output is off due to output overload and bypass abnormal. Please check it

Output off,

voltage is not

zero

When there is no output, the system detects that the output has a voltage

Output pending Remote shutdown is enabled, and the system will be off

Output short Check that the output cables are not shorted

Output voltage

abnormal The output voltage exceeds the normalvoltage range.

Table 4.4 Alarm Messages (continued)

Vertiv | Liebert® GXT5™ Installer/User Guide

MESSAGE DESCRIPTION

Rectifier fault The rectifier is faulty and off because the bus voltage exceeds the range when the rectifier starts or soft starts.

Rectifier

overload

The output power is larger than the rectifier overload point. Check that the input voltage meets the output load,

mains input 176 V ~ 100 V, the load 100% ~ 50% linear derating

Remote power-

on Remotely power on

Remote shut-

off Remotely power off

Remote

shutdown Dry contact activated at any mode shutdown

REPO Shutdown caused by the REPO terminal Normally Closed contact open

Restore factory

defaults Under UPS stand-by state, set 'Restore Factory Defaults' function via the Maintain page

Shutdown due

to overtemp

During the UPS operation, the system checks that the heat sink temperature exceeds the setting range.

If overtemperature, please check:

1. Ambient temperature too high or not

2. Dust is blocked or not

3. Fan fault or not

System fault Alarm when model configuration is incorrect. Contact Vertiv Technical support.

System

overtemp

Internal heat sink temperature too high, and the inverter is off. The alarm can only be silenced if the heat-sink

temperature is lower than the alarm setting. The system can automatically start after overtemperature fault is

solved.

If overtemperature, please check:

1. Ambient temperature too high or not

2. Dust is blocked or not

3. Fan fault or not

Turn off

programmable

outlet

The programmable-outlet status changed from "Turn On" to "Turn Off"

Turn on fail The UPSdoes not start because there is no mains/utility power or it is greater than the voltage required to supply

the full load. Check the AC input power.

Turn on

programmable

outlet.

The programmable-outlet status changed from "Turn Off" to "Turn On."

UPS has no

output Both Inverter and Bypass provide no power supply.

UPS is out of

service The UPS is out of service.

Table 4.4 Alarm Messages (continued)

4 Operation and Display Panel 39

About Screen

The About screen offers tabs that list information about the product and the network. The Efficiency tab

shows a chart of battery efficiency versus capacity. The Battery age tab show a chart of SOHpercentage

versus battery age in years.

To view the product and network information:

1. At the main menu, select the About icon, and press Enter.

2. Use the arrow buttons to move the cursor left/right and select a tab, then press Enter to

display the information for the selected tab.

Figure 4.8 About Screen Tabs

ITEM DESCRIPTION

Screen tabs with Efficiency tab selected.

NOTE: The tab shown in the figure is an example of the graph and does not represent the actual capacity values for

your UPS model.

Product information

Product Type

UPS model number.

Serial number

UPSserial number.

Time since startup

Elapsed time since start-up of the UPS.

Boot FW version

Version of MCU boot firmware on the monitor board.

Vertiv | Liebert® GXT5™ Installer/User Guide

Monitor FW version

Version of MCU application firmware on the monitor board.

DSP FW version

Version of DSP firmware on the UPS power-module control board.

4.3 Editing Display and Operation Settings

You may adjust the display settings and UPS configuration via the LCD. The display and operation

settings are password protected. The default password is 111111 (six ones).

NOTE: We recommend that you change the password to protect your system and equipment and

record the new password and store it in an accessible location for later retrieval. See Changing the

Password below.

To enter the password:

1. Press the up-arrow button to change the digit, then press the down-arrow button to move to

the next digit.

2. Repeat to select each digit, and press Enter to submit the password.

Figure 4.9 Password Prompt

4.3.1 Changing the Password

The default password is 111111 (six ones). You must use the current password to change the password.

NOTE: We recommend that you change the password from the default to protect your system and

equipment. Record the new password and store it in an accessible location for later retrieval.

1. At the main menu, select the Settings icon, and press Enter.

2. At the password prompt, use the up-arrow to select the first digit, press the down-arrow to

move to the next digit, repeat for each digit, then press Enter to access the settings.

3. Use the arrow buttons to select the Monitor tab, then press Enter.

4 Operation and Display Panel 41

4. Use the down arrow to highlight Change Settings Password, press Enter, and re-enter the

current password.

The Input new password dialog opens, see Figure 4.10 below.

5. Enter the new password, then confirm the new password.

A confirmation dialog opens to indicate a successful password change.

6. Press ESC to return to the settings or main menu.

Figure 4.10 New and Confirm Password dialogs

4.3.2 Selecting the Display Language

The LCD is multilingual. The available languages are English, French, Portuguese, Spanish, Chinese,

German, Japanese, and Russian.

To change the language:

1. At the main menu, select the Settings icon, and press Enter.

2. At the password prompt, use the up-arrow to select the first digit, press the down-arrow to

move to the next digit, repeat for each digit, then press Enter to access the settings.

3. Use the arrow buttons to select the Monitor tab, then press Enter.

4. Use the down arrow to highlight Language, then press Enter.

5. Use the up/down arrows to select the language, then press Enter.

All the LCD elements display in the selected language.

4.3.3 Setting the Date and Time

To adjust the date and time:

1. At the main menu, select the Settings icon, and press Enter.

2. At the password prompt, use the up-arrow to select the first digit, press the down-arrow to

move to the next digit, repeat for each digit, then press Enter to access the settings.

3. Use the arrow buttons to select the Monitor tab, then press Enter.

4. Use the down arrow to highlight Date or Time, then press Enter.

5. Use the up/down arrows to select the date/time, then press Enter to confirm.

Vertiv | Liebert® GXT5™ Installer/User Guide

5 MAINTENANCE

WARNING! Risk of electric shock. Can cause equipment damage, injury and death. A battery

can present a risk of electrical shock and high short-circuit current.

WARNING! Risk of electric shock. Can cause injury or death. Hazardous mains and/or battery

voltage exists behind the protective cover No user accessible parts are located behind the

protective covers that require a tool for removal. Only qualified service personnel are

authorized to remove such covers. If maintenance for rack is needed, notice that the neutral

line is live.

Observe the following precautions when working on batteries:

•Remove watches, rings and other metal objects.

•Use tools with insulated handles.

•Wear rubber gloves and boots.

•Do not lay tools or metal parts on top of batteries.

•Disconnect charging source prior to connecting or disconnecting battery terminals.

•If the battery kit is damaged in any way or shows signs of leakage, contact your Vertiv

representative immediately.

•Handle, transport, and recycle batteries in accordance with local regulations.

•Determine if the battery is inadvertently grounded. If it is inadvertently grounded, remove the

source of the ground. Contact with any part of a grounded battery can result in electrical

shock. The likelihood of such shock will be reduced if grounds are removed during installation

and maintenance (applicable to a UPS and a remote battery supply not having a grounded

supply circuit).

5.1 Replacing Batteries

WARNING! Risk of electric shock. Can cause injury or death. Disconnect all local and remote

electric power supplies before working with the UPS. Ensure that the unit is shut down and

power has been disconnected before beginning any maintenance.

WARNING! Risk of electric shock and explosion. Can cause equipment damage, injury and

death. Do not dispose of the battery in a fire. The battery may explode. Do not open or damage

the battery. Released electrolyte is toxic and is harmful to skin and eyes. If electrolyte comes

into contact with the skin, wash the affected area immediately with plenty of clean water and

get medical attention.

WARNING! Risk of electric shock. Can cause equipment damage, injury and death. A battery

can present a risk of electrical shock and high short-circuit current.

5 Maintenance 43

WARNING! Risk of explosion. Can cause equipment damage, injury and death. A battery can

explode if the battery is replaced by an incorrect type. Dispose of used batteries according to

the instructions included with the battery-pack.

Read all safety cautions before proceeding. A trained user can replace the internal battery pack when the

UPS is in a restricted access location (such as a rack or server closet). To obtain the appropriate

replacement battery pack(s), refer to Table 5.1 below, and contact your local dealer or Vertiv

representative.

UPS MODEL NUMBER BATTERY PACK MODEL NUMBER QUANTITY REQUIRED

GXT5-500LVRT2UXL

GXT5-36BATKIT 1GXT5-750LVRT2UXL

GXT5-1000LVRT2UXL

GXT5-1500LVRT2UXL

GXT5-48BATKIT 1

GXT5-2000LVRT2UXL

GXT5-3000LVRT2UXL GXT5-72BATKIT 1

Table 5.1 Replacement Battery-pack Model Numbers

To replace a battery pack:

NOTE: The internal battery pack is hot-swappable. However, you must exercise caution because;

during this procedure, the load is unprotected from disturbances and power outages. Do not replace

the battery while the UPS is operating in Battery Mode. This will result in a loss of output power and will

drop the connected load.

1. Press the button on the left-front of the UPS front panel, and pull the panel open, then, loosen

and remove the screw from the battery door, see Figure 5.1 on the facing page.

2. Lay the battery door and screw aside for reassembly.

3. Grasp the battery handle, and pull out the battery pack, see Figure 5.1 on the facing page.

4. Unpack the replacement battery pack, taking care not to damage the packaging to re-use

when disposing of the old battery.

5. Compare the new and old battery pack to make sure they are the same type and model. If so,

proceed with step 6. If they are different, stop and contact your Vertiv representative, or

Technical Support, http://www.Vertiv.com/en-us/support/.

6. Line-up and slowly push-in each replacement battery pack. The battery is fully-inserted if the

battery door fits flush against the UPS.

7. Re-attach the battery door with the screw, and replace the front cover.

8. Activate the new battery pack(s) using the operating/display panel:

NOTE: The display menus and functions are described in Operation and Display Panel on page23.

•From the main menu, select Settings, then the Monitoring tab and verify that the date

and time are correct. If the date or time need correction, see Setting the Date and Time

on page42.

Vertiv | Liebert® GXT5™ Installer/User Guide

•Select the Battery tab, use the arrows to select Replace Battery, and press Enter.

The replaced battery packs are activated.

•Use ESC to return to the main display.

Figure 5.1 Replacing the Battery Pack

ITEM DESCRIPTION

1 Battery pack

2 Battery door

3 Front panel

5.2 Charging Batteries

The batteries are valve-regulated, non-spillable, lead acid and should be kept charged to attain their

design life. The UPS charges the batteries continuously when it is connected to the utility input power.

If the UPS will be stored for a long time, We recommend connecting the UPS to input power for at least 24

hours every 4 to 6months to ensure full recharge of the batteries.

5 Maintenance 45

5.3 Checking UPS Operation

NOTE: Operation-check procedures may interrupt power supply to the connected load.

We recommend checking the UPS operation once every 6months.

Back-up the load data before conducting the check.

1. Press the power button to check the indicators and display function.

2. Check for alarm or fault indicators on the operation/display panel.

3. Make sure that there are no audible or silenced alarms.

4. Select the Setting menu, and look at the log for alarm and fault history.

5. Check the operating mode for Normalmode. If the UPS is operating in Bypass mode, contact

Vertiv Technical Support.

6. Check to see if batteries are discharging (operating in Battery mode) and utility power is

normal. If so, contact Vertiv Technical Support.

5.4 Cleaning the UPS

WARNING! Risk of electric shock. Can cause injury or death. Disconnect all local and remote

electric power supplies before working with the UPS. Ensure that the unit is shut down and

power has been disconnected before beginning any maintenance.

WARNING! Risk of electric shock. Can cause injury or death. Hazardous mains and/or battery

voltage exists behind the protective cover No user accessible parts are located behind the

protective covers that require a tool for removal. Only qualified service personnel are

authorized to remove such covers. If maintenance for rack is needed, notice that the neutral

line is live.

The UPS requires no internal cleaning. If the outside of the UPS becomes dusty, wipe with a dry cloth. Do

not use liquid or aerosol cleaners. Do not insert any objects into the ventilation holes or other openings in

the UPS.

Vertiv | Liebert® GXT5™ Installer/User Guide

6 TROUBLESHOOTING

This section indicates various UPS symptoms you may encounter and provides a troubleshooting guide in

the event the UPS develops a problem. Use the following information to determine whether external

factors caused the problem and how to remedy the situation.

6.1 Symptoms that Require Troubleshooting

The following symptoms indicate the UPS is malfunctioning:

•The relative indicators illuminate, indicating the UPS has detected a problem.

•An alarm buzzer sounds, alerting the user that the UPS requires attention.

6.2 Audible Alarm (Buzzer)

An audible alarm accompanies various events during UPS operations. Table 6.1 below, describes the

sounds and their meaning. To silence an alarm, see Silencingthe Audible Alarm on page21.

SOUND INDICATES:

Continuous beep Generated when a UPS fault appears, such as a fuse or hardware failure.

One beep every 0.5 seconds Generated when a UPS critical alarm appears, such as on inverter overload.

One beep every 1 second Generated when a UPS critical alarm appears, such as on battery low voltage.

One beep every 3.3 seconds Generated when a UPS general alarm appears.

Table 6.1 Audible-alarm Descriptions

NOTE: When an alarm is indicated, an alarm message is logged. Table 4.4 on page36, describes the

alarm messages you may see. When a fault is indicated, front-panel display list the fault, which are

described in Table 6.2 below.

6.2.1 Faults

When the fault indicator is illuminated, the LCD displays the fault. The faults are described in Table 6.2

below.

DISPLAYED FAULT CAUSE CORRECTIVE STEPS

Battery test fail The battery is bad or weak. Contact technical support.

Rectifier fault A rectifier failure occurred. Contact technical support.

Inverter overload,

Bypassovercurrent The UPS is overloaded, Bypass is over current. Reduce the load and contact technical

support.

Inverter fault The inverter is faulty. Contact technical support.

Battery aged The battery is bad or weak. Replace the battery.

Output short The output connection is short-circuited. Shut-down the equipment and contact

technical support.

DCbus fail The DCbus is faulty. Contact technical support.

Table 6.2 Description of displayed faults

6 Troubleshooting 47

DISPLAYED FAULT CAUSE CORRECTIVE STEPS

System overtemp Over-temperature condition in the UPS. The UPS will

transfer to bypass mode.

Reduce the load and contact technical

support.

Charger fault The charger is faulty. Contact technical support.

Fan fault At least one fan is faulty. Contact technical support.

DC/DC fault A DC-DC charger failure occurred. Contact technical support.

Table 6.2 Description of displayed faults (continued)

6.3 Troubleshooting UPS Issues

In the event of an issue with the UPS, refer to Table 6.3 below, to determine the cause and solution. If the

fault persists, contact Vertiv Technical Support. Visit the GXT5 product page at www.Vertiv.com for

contact information.

When reporting a UPS issue to Vertiv, include the UPS model and serial number. These are located in

several places for your ease of location:

•on the top panel (rack mount orientation)

•the left side (tower orientation)

•the rear panel

•on the front of the unit behind the front plastic bezel

•on the LCD select Main Menu > About.

PROBLEM CAUSE SOLUTION

UPS fails to

start

UPS is short-

circuited or

overloaded

Ensure UPS is Off. Disconnect all loads and ensure nothing is lodged in output receptacles.

Ensure loads are not defective or shorted internally.

Batteries are not

charged enough or

not connected

Check to ensure the internal battery is connected. If it is not, make the connection and try to

start the unit. If the battery is connected, leave the UPS connected to input power for

24hours to recharge batteries, then try to start the unit.

UPS has

reduced

battery

backup time

Batteries are not

fully charged Keep UPS plugged in continuously at least 24 hours to recharge batteries.

UPS is overloaded Check load level indicator and reduce the load on the UPS.

Batteries may not be

able to hold a full

charge due to age

Replace batteries. Contact your Vertiv representative or Vertiv TechnicalSupport for

replacement battery kit.

Table 6.3 Troubleshooting

Vertiv | Liebert® GXT5™ Installer/User Guide

7 SPECIFICATIONS

MODEL: GXT5- 500LVRT2UXL 750LVRT2UXL 1000LVRT2UXL

RATING 500VA/500W 750VA/750W 1000VA/1000W

Dimensions, in. (mm)

Unit, D x W x H 15.7 x 16.9 x 3.4 (400 x 430 x 85)

Shipping, D x W x H 24.3 x 22.4 x 10.3 (617 x 570 x 262)

Weight, lb (kg)

Unit 37 (16.8)

Shipping 49.9 (22.68)

Input AC Parameters

Voltage Range (typical). 120VAC nominal, variable based on output load

90% ~ 100% loading 94 ~ 102VAC/149.5VAC

70% ~ 90% loading 77 ~ 94VAC/149.5VAC

50% ~ 70% loading 60 ~ 77VAC/149.5VAC

0% ~ 50% loading 60VAC/149.5VAC

Frequency 40Hz ~ 70Hz; auto-sensing

Input Power Cord 10-ft. (3m)attached with NEMA 5-15P plug

Output AC Parameters

Output Receptacles 5-15R x 6

Voltage 100/110/115/120/125VAC (user-configurable); ±3%

Waveform Sine wave

Utility (AC) Mode Overload > 200% for 250mS, 150–200% for 2seconds; 125–150% for for 60 seconds;

Table 7.1 UPS Specifications, 500VA to 1000 VA models

7 Specifications 49

MODEL: GXT5- 500LVRT2UXL 750LVRT2UXL 1000LVRT2UXL

RATING 500VA/500W 750VA/750W 1000VA/1000W

Battery Parameters

Type Valve-regulated, non-spillable, lead acid

Quantity x Voltage x Rating 3 x 12V x 9.0AH

Battery Mfr./Part # LEOCH/DJW12-9.0

Back-up time See Battery Run Times on page54.

Recharge time 3hours to 90% capacity after full discharge with 100% load til UPS auto-shutdown (internal

batteries only)

Environmental Requirements

Operating Temperature, °F

(°C) 32to122 (0to50)

Storage Temperature, °F (°C) –4to 140 (–20 to 60) [batteries are from 5 to 104 (–15 to 40)]

Relative Humidity 0%–95% non-condensing

Operating Elevation Up to 10,000ft (3,000m) at 77°F (25°C) without derating

Audible Noise <46dBA max. at 3ft (1m) front and sides, <43dBA max. at 3ft (1m) rear

Agency

Surge Immunity ANSIC62.41 Category B

Transportation ISTA Procedure 1A

Table 7.1 UPS Specifications, 500VA to 1000 VA models (continued)

Vertiv | Liebert® GXT5™ Installer/User Guide

MODEL: GXT5- 1500LVRT2UXL 2000LVRT2UXL 3000LVRT2UXL

RATING 1500VA/ 1350W 2000VA/ 1800W 3000VA/ 2700W

Dimensions, in. (mm)

Unit, D x W x H 18.5 x 16.9 x 3.4 (470 x 430 x 85) 21.3 x 16.9 x 3.4 (540 x 430

x 85)

Shipping, D x W

x H 24.3 x 22.4 x 10.3 (617 x 570 x 262) 28.2 x 22.4 x 10.3 (717 x 570

x 262)

Weight, lb (kg)

Unit 46.2 (21) 47.5 (21.6) 66 (30)

Shipping 57.4 (26.1) 58.7 (26.7) 77.2 (35.1)

Input AC Parameters

Voltage Range

(typical). 120VAC nominal, variable based on output load

90% ~ 100%

loading 94 ~ 102VAC/149.5VAC

70% ~ 90%

loading 77 ~ 94VAC/149.5VAC

50% ~ 70%

loading 60 ~ 77VAC/149.5VAC

0% ~ 50%

loading 60VAC/149.5VAC

Frequency 40Hz ~ 70Hz; auto-sensing

Input Power

Cord

10-ft. (3m)attached

with NEMA 5-15P plug

10-ft. (3m)attached

with NEMA 5-20P plug

10-ft. (3m)attached

with NEMA 5-30P plug

Output AC Parameters

Output

Receptacles 5-15R x 6 L5-20R + 5-15/20R x 6 L5-30R + 5-15/20R x 6

Voltage 100/110/115/120/125VAC (user-configurable); ±3%

Waveform Sine wave

Utility (AC)

Mode Overload

> 200% for 250mS;

150–200% for 2seconds;

125–150% for for 50 seconds;

105 – 125% for 60seconds

> 200% for 250mS;

150–200% for 2seconds;

125–150% for for 10

seconds;

105 – 125% for 15seconds

Table 7.2 UPS Specifications, 1500VA to 3000 VA models

7 Specifications 51

MODEL: GXT5- 1500LVRT2UXL 2000LVRT2UXL 3000LVRT2UXL

RATING 1500VA/ 1350W 2000VA/ 1800W 3000VA/ 2700W

Battery Parameters

Type Valve-regulated, non-spillable, lead acid

Quantity x

Voltage x Rating 4 x 12V x 9.0AH 6 x 12V x 9.0AH

Battery

Mfr./Part # LEOCH/DJW12-9.0

Back-up time See Battery Run Times on page54.

Recharge time 4hours to 90% capacity after full discharge with 100%

load til UPS auto-shutdown (internal batteries only)

3hours to 90% capacity after full discharge with 100%

load til UPS auto-shutdown (internal batteries only)

Environmental Requirements

Operating

Temperature,

°F (°C)

32to122 (0to50)

Storage

Temperature,

°F (°C)

–4to 140 (–20 to 60) [batteries are from 5 to 104 (–15 to 40)]

Relative

Humidity 0%–95% non-condensing

Operating

Elevation Up to 10,000ft (3,000m) at 77°F (25°C) without derating

Audible Noise <46dBA max. at 3ft (1m) front and sides, <45dBA max.

at 3ft (1m) rear

<48dBA max. at 3ft (1m) front and sides, <48dBA max.

at 3ft (1m) rear

Agency

Surge Immunity ANSIC62.41 Category B

Transportation ISTA Procedure 1A

Table 7.2 UPS Specifications, 1500VA to 3000 VA models (continued)

Vertiv | Liebert® GXT5™ Installer/User Guide

MODEL NUMBER: GXT5-EBC36VRT2U GXT5-EBC48VRT2U GXT5-EBC72VRT2U

USED WITH UPS MODEL: 500–1000 VA MODELS 1500–2000 VA MODELS 3000 VA MODELS

Dimensions, D x W x H, in. (mm)

Unit 14.6 x 16.9 x 3.3

(370 x 430 x 85)

19.7 x 16.9 x 3.3

(497 x 430 x 85)

23.7 x 16.9 x 3.3

(602 x 430 x 85)

Shipping 24.3 x 22.4 x 10.3

(617 x 570 x 262)

28.2 x 22.4 x 10.3

(717 x 570 x 262)

Weight, lb (kg)

Unit 49.72 (22.6) 63.36 (28.8) 90.64 (41.2)

Shipping 63.14 (28.7) 77 (35) 104.72 (47.6)

Battery Parameters

Type Valve-regulated, non-spillable, lead acid

Quantity x Voltage 2x 3 x12V x 9.0Ah 2x 4 x12V x 9.0Ah 2x 6 x12V x 9.0Ah

Battery Mfr./Part# LEOCH/DJW12-9.0

Back-up Time See Battery Run Times on the next page.

Environmental

Operating Temperature, °F(°C) 32 to 104 (0 to 40)

Storage Temperature, °F(°C) 5 to 122 (–15 to 50)

Relative Humidity 0%–95% non-condensing

Operating Elevation Up to 10,000ft (3,000m) at 104°F (40°C)

Storage Elevation 50,000ft (15,0000m) maximum

Agency

Safety UL1778 4th Edition and CSA22.2No.107.1

RFI/EMI FCC Part 15 Class A

Surge Immunity ANSIC62.41 Category B

Transportation ISTA Procedure 1A

Table 7.3 External Battery Cabinet Specifications

7 Specifications 53

7.1 Battery Run Times

NO. OF EBCS

LOAD

PERCENTAGE

OF CAPACITY

120 VAC

500 VA 750 VA 1000 VA 1500 VA 2000 VA 3000 VA

(UPS only)

10% 165.5 118 92.5 88 66.5 70

20% 92.5 63.5 47 42.5 30 31.5

30% 63.5 41 29 25.5 17.5 18.5

40% 47 29 20 17.5 12 12.5

50% 36.5 21.5 15 13 9 9

60% 29 17 11.5 10.5 7 7

70% 24 14 9.5 8.5 5.5 6

80% 20 11.5 8 7 4.5 4.5

90% 17 10 7 6 3.5 4

100% 15 8.5 6 5 3 3

+1 EBC

10% 572 421 330 314 237 249.5

20% 330 226 168.5 154 113.5 117.5

30% 226 148 110.5 100.5 74.5 77.5

40% 168.5 110.5 82.5 74.5 55 56.5

50% 132 88 65 59 42 43.5

60% 110.5 73 53.5 48 33.5 34.5

70% 94.5 62 .44.5 39.5 27.5 28

80% 82.5 53.5 38 33.5 23 23.5

90% 73 46.5 33 28.5 19.5 20

100% 65 41 28.5 25 17 17

+2 EBC

10% 978.5 727 575.5 549 420 441

20% 575.5 402 305.5 281.5 208 216.5

30% 402 272 201.5 183 132 137

40% 305.5 201.5 146.5 132 98.5 101.5

50% 244.5 158 116 105.5 78 80

60% 201.5 128.5 96 87.5 64 65.5

70% 170.5 110 82 74 54 55.5

80% 146.5 96 71 64 46 47

90% 128.5 85 63 56 40 40.5

100% 116 76 56 49.5 35 35.5

Table 7.4 Battery Run Time in Minutes

Vertiv | Liebert® GXT5™ Installer/User Guide

NO. OF EBCS

LOAD

PERCENTAGE

OF CAPACITY

120 VAC

500 VA 750 VA 1000 VA 1500 VA 2000 VA 3000 VA

+3 EBC

10% 1385 1032.5 820.5 783.5 603.5 632.5

20% 820.5 578 443 409 306.5 318

30% 578 396 297.5 271 199.5 207

40% 443 297.5 220.5 199.5 144 148.5

50% 357 236 172.5 155.5 113.5 116.5

60% 297.5 194 140 127 94 96

70% 254 163.5 119 108 79.5 81.5

80% 220.5 140 104 94 69 70.5

90% 194 123.5 92.5 82.5 60.5 61.5

100% 172.5 111 82.5 74 54 54.5

+4 EBC

10% 1791 1338.5 1066 1018

879+

935

20% 1066 754 580.5 537 404.5 419.5

30% 754 519.5 393.5 359.5 267 277

40% 580.5 393.5 294 267 196 202

50% 470 314.5 232.5 210.5 152 156

60% 393.5 260 191 172 124 127

70% 337 221 160.5 143.5 105.5 108

80% 294 191 137.5 124 91.5 94

90% 260 167.5 122 109.5 81 82.5

100% 232.5 148.5 109 98 72 73

+5 EBC

10% 2197.5 1644 1311 1252.5 969.5 1015.5

20% 1311 930 718 664.5 503 521

30% 930 643.5 489 447.5 335 347

40% 718 489 368 335 248 255

50% 582.5 392.5 292.5 265.5 194.5 199.5

60% 489 326.5 241.5 219 157.5 162

70% 420.5 278 204.5 184 131.5 135

80% 368 241.5 176.5 157.5 114.5 117

90% 326.5 213 154.5 137 101 103

100% 292.5 190 136.5 122.5 90.5 92

Table 7.4 Battery Run Time in Minutes (continued)

7 Specifications 55

NO. OF EBCS

LOAD

PERCENTAGE

OF CAPACITY

120 VAC

500 VA 750 VA 1000 VA 1500 VA 2000 VA 3000 VA

+6 EBC

10% 2604 1950 1556.5 1487 1152.5 1207.5

20% 1556.5 1106 855 792.5 601.5 622.5

30% 1106 767.5 585 536 402.5 417

40% 855 585 441.5 402.5 300 308.5

50% 695.5 470.5 353 320.5 236.5 242.5

60% 585 392.5 292.5 265.5 1983 198

70% 503.5 335.5 249 224 161.5 166.5

80% 441.5 292.5 215.5 193 138 142

90% 392.5 258.5 189.5 168.5 121.5 124

100% 353 231 168 149 109 110.5

Table 7.4 Battery Run Time in Minutes (continued)

Vertiv | Liebert® GXT5™ Installer/User Guide

APPENDICES

Appendix A: Technical Support

Our Technical Support staff is ready to assist you with any installation or operating issues you may

encounter with your Liebert® product. Please call or e-mail us:

In Europe, Middle East, and Asia:

EMEA Multi-Language Technical support:

e: eoc@vertivco.com

p: Toll free 0080011554499

p: Toll +39 02 98250222

In the United States:

Technical support:

e: liebert.upstech@vertivco.com

p: 1-800-222-5877 menu option 1

Monitoring support:

e: liebert.monitoring@vertivco.com

p: 1-800-222-5877 menu option 2

Warranty support:

e: microups.warranty@vertivco.com

p: 1-800-222-5877 menu option 3

Vertiv | Liebert® GXT5™ Installer/User Guide

This page intentionally left blank

Vertiv | Liebert® GXT5™ Installer/User Guide

Vertiv.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA

logos referred to are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure

accuracy and completeness herein, Vertiv Group Corp. assumes no responsibility, and disclaims all liability, for damages resulting from use of this information

or for any errors or omissions. Specifications are subject to change without notice.

590-1933-501A

Table of Contents

Vertiv GXT5-EBC72VRT2U User Manual

Related Manuals