Table of Contents
- 1 Important Safety Instructions
- 2 Vertiv™ VR
- 3 Pre-installation Preparation
- 4 Installation and Assembly Procedures
- 4.1 Removing and Reversing Doors
- 4.2 Reversing the door handle
- 4.3 Removing and Replacing Side Panels
- 4.4 Removing and Replacing the Top Panel
- 4.5 Installing the Edge Guard
- 4.6 Positioning and Attaching Front‑ and Rear‑Mount 19‑in. EIA Rails
- 4.7 Mounting Power Distribution Units
- 4.8 Baying the Racks
- 4.9 Grounding the Rack
- 4.10 Loading Equipment into the Rack
- 5 Periodic Maintenance
Vertiv VR3300TAA User Manual
Displayed below is the user manual for VR3300TAA by Vertiv which is a product in the Rack Cabinets category. This manual has pages.
Related Manuals
Vertiv™ VR
Installer/User Guide
Vertiv | VR Installer/User Guide
Technical Support Site
If you encounter any installation or operational issues with your product, check the pertinent
section of this manual to see if the issue can be resolved by following outlined procedures.
Visit https://www.VertivCo.com/en-us/support/ for additional assistance.
The information contained in this document is subject to change
without notice and may not be suitable for all applications. While every
precaution has been taken to ensure the accuracy and completeness
of this document, Vertiv assumes no responsibility and disclaims all
liability for damages resulting from use of this information or for any
errors or omissions. Refer to other local practices or building codes as
applicable for the correct methods, tools, and materials to be used in
performing procedures not specifically described in this document.
The products covered by this instruction manual are manufactured
and/or sold by Vertiv. This document is the property of Vertiv and
contains confidential and proprietary information owned by Vertiv. Any
copying, use or disclosure of it without the written permission of Vertiv
is strictly prohibited.
Names of companies and products are trademarks or registered
trademarks of the respective companies. Any questions regarding
usage of trademark names should be directed to the original
manufacturer.
TABLE OF CONTENTS
1 Important Safety Instructions 5
2 Vertiv™ VR 7
2.1 What’s Included with Your Vertiv VR 8
3 Pre-installation Preparation 9
3.1 Equipment Inspection 9
3.2 Unloading the Rack andMovingtoInstallationLocation 9
3.2.1 Leveling Feet Adjustment 11
3.3 Equipment Clearance Requirements 12
4 Installation and Assembly Procedures 13
4.1 Removing and Reversing Doors 13
4.2 Reversing the door handle 14
4.2.1 Operating Door Handle 15
4.3 Removing and Replacing Side Panels 15
4.4 Removing and Replacing the Top Panel 17
4.5 Installing the Edge Guard 18
4.6 Positioning and Attaching Front-andRear-Mount19-in.EIARails 18
4.7 Mounting Power Distribution Units 22
4.7.1 Installing and Positioning a Full-height PDU/Cable-Management Bracket 22
4.8 Baying the Racks 23
4.9 Grounding the Rack 25
4.10 Loading Equipment into the Rack 26
5 Periodic Maintenance 27
Vertiv | VR Installer/User Guide | 3
Vertiv | VR Installer/User Guide | 4
1 IMPORTANT SAFETY INSTRUCTIONS
Save These Instructions
This manual contains important instructions that must be closely followed during installation of this unit
to maintain compliance with agency listings. Read all safety and operating instructions. Adhere to all
warnings on the unit and in this manual. Follow all operating and user instructions.
WARNING! Risk of handling heavy unit. Can cause equipment damage, injury or death. Read all
instruction before beginning.
WARNING! Risk of top-heavy unit falling over. Improper handling can cause equipment
damage, injury or death. Only properly trained and qualified personnel wearing appropriate
OSHA-approved personal protection equipment (PPE) should attempt to move, lift, remove
packaging from or prepare unit for installation. Read all instructions before attempting to move,
lift, remove packaging from or prepare the unit for installation.
This product is designed for commercial/industrial use only. This product is not intended for use with life
support or other U.S. FDA designated “critical” devices. Maximum loads must not exceed those specified in
this manual. The maximum load rating for the Vertiv VR is found in the "Vertiv VR Guide Specifications,"
SL-11425GS. Do not exceed the static load rating.
Install and operate in a clean environment, free from moisture, flammable liquids, gases and corrosive
substances. The Vertiv VR must be installed on a flat, level surface for proper assembly and operation.
Ensure that the rack has proper ventilation. Never block or insert objects into the ventilation holes or
other openings. Maintain minimum clearances as specified in this manual.
Provide the minimum space between the accessories/components and the housing. This spacing shall be
maintained for safe operation of the equipment when installed in accordance with the National Electric
Code, ANSI/NFPA 70.As appropriate, all wiring and equipment should be installed in accordance with
NFPA 70, “National Electrical Code,” and the applicable sections of ANSI C2, “National Electrical Safety
Code."
We recommend that casters only be used to move empty racks.
Vertiv | VR Installer/User Guide | 5
Vertiv | VR Installer/User Guide | 6
This page intentionally left blank.
2 VERTIV™ VR
The highly-versatile Vertiv VR provides an organized, secure, controlled environment in a single system
for sensitive electronic equipment.
Table 2.1 below,lists the racks described in this guide.
Part Number Type Height, RU Height,
mm(in.)
Width,
mm(in.)
Depth,
mm(in.)
Unit Weight,
kg (lb)
Shipping Weight,
kg (lb)
VR3100
Server 42 1998 (78.67) 600 (23.62) 1100 (43.31) 127 (280)
163 (359.4)
VR3100TAA*
VR3100SP* 186 (410.1)
VR3300
Server 42 1998 (78.67) 600 (23.62) 1200 (47.24) 137 (302)
173 (381.4)
VR3300TAA*
VR3300SP* 196 (432.1)
VR3150
Networking 42 1998 (78.67) 800 (31.5) 1100 (43.31) 162 (357.1)
202 (445.3)
VR3150TAA*
VR3150SP* 224 (493.8)
VR3350
Networking 42 1998 (78.67) 800 (31.5) 1200 (47.24) 166 (366)
206 (454.2)
VR3350TAA*
VR3350SP* 228 (502.7)
VR3107
Server 48 2265 (89.17) 600 (23.62) 1100 (43.31) 162 (357.1)
199 (438.7)
VR3107TAA*
VR3107SP* 222 (489.4)
VR3307
Server 48 2265 (89.17) 600 (23.62) 1200 (47.24) 166 (366)
203 (447.5)
VR3307TAA*
VR3307SP* 225 (496)
VR3157
Networking 48 2265 (89.17) 800 (31.5) 1100 (43.31) 175 (385.8)
216 (476.2)
VR3157TAA*
VR3157SP* 238 (524.7)
VR3357
Networking 48 2265 (89.17) 800 (31.5) 1200 (47.24) 180 (396.8)
220 (485)
VR3357TAA*
VR3357SP* 242 (533.5)
*Availability of SKUs varies by global region.
Table 2.1 Vertiv VR Models, Types, Nominal Dimensions, and Weights
Vertiv | VR Installer/User Guide | 7
2.1 What’s Included with Your Vertiv VR
•Vertiv VR assembled rack
•Door and side-panel keys
•(50) M6 cage nuts and M6 screws
•Baying hardware
•Edge grommet
•Cage-nut install tool
•T30 extension drive
Vertiv | VR Installer/User Guide | 8
3 PRE-INSTALLATION PREPARATION
3.1 Equipment Inspection
Upon receiving a Vertiv VR rack system, inspect the packaging for any signs of mishandling or damage. If
any damage is noted, notify your local Vertiv representative and your carrier immediately.
3.2 Unloading the Rack andMovingtoInstallationLocation
Before unloading, note the weight of the model in Table 2.1 on page7.
The following tools/equipment are required to un-pack and move the rack:
•pallet jack or forklift
•utility knife or scissors
•13-mm socket and ratchet or 13-mm wrench
•14-mm socket and ratchet or 14-mm wrench
WARNING! Only trained service personnel should be used to remove the rack from the pallet.
Also, be sure you have a sufficient number of service personnel. Do not attempt to move racks
by yourself.
WARNING! Be careful when moving racks before installation. Sudden stops and starts,
excessive force, obstructed routes, and uneven floor surfaces may cause the rack to topple
over.
CAUTION: Use at least two people when moving the unit.
1. Using a pallet jack or forklift, move the rack on its pallet to the installation location.
2. Cut the shrink wrap and remove all packaging.
3. Use a 13-mm socket or a 13-mm wrench to remove the anchor-bracket hardware that secure
the 2 anchor brackets to the shipping pallet, one in the front and one at the rear of the rack.
Each bracket is secured by four bolts.
•If the brackets will be used to anchor the rack to the floor, and set aside for attachment
when the rack is in its final location.
4. Make sure that the leveling feet are in the raised position, see Leveling Feet Adjustment on
page 11.
5. Use a pallet jack or forklift to raise the rack off the shipping pallet.
6. Slide the shipping pallet out from under the rack.
Vertiv | VR Installer/User Guide | 9
7. Position the rack in the installation location using the forklift, with a pallet jack, or with 2 or more
people rolling the rack on its casters.
•If using the casters to move the rack, make sure that the leveling feet are raised before
moving, see Leveling Feet Adjustment on page 11.
8. Position the rack, lower the leveling feet using the T30 Torx tool or 14-mm wrench, and level
the rack.
•If using the shipping/anchoring brackets to bolt the rack to the floor, make sure that the
rack is level before tightening all the anchor-bracket hardware, see Leveling Feet
Adjustment on page 11.
Figure 3.1 Anchor brackets inside front/rear of rack
Item Description
1 Bolt holes for securing anchor bracket to pallet and/or floor
2 Bolt holes for securing anchor bracket to rack (3 typical)
Vertiv | VR Installer/User Guide | 10
3.2.1 Leveling Feet Adjustment
Leveling feet are preinstalled at the factory. They are easily accessible in the front and rear of the rack
frame.
•If necessary, use the T30 Torx tool or 14-mm wrench to raise/lower the levelers.
Figure 3.2 Adjusting the leveling-feet
Item Description
1 Counter-clockwise rotation to adjust feet up
2 Clockwise rotation to adjust feet down
3 Adjusting feet beneath rack
4 Adjusting feet from inside the rack
Vertiv | VR Installer/User Guide | 11
3.3 Equipment Clearance Requirements
When planning the position and location of the rack, refer to Figure 3.3 below, for the required
clearances for installation and service of the rack and installed equipment.
Figure 3.3 Required clearance
Item
600-mm (23.62in.) wide, mm (in.) 800-mm (31.5 in.) wide, mm (in.)
x 1100mm (43.31 in.) x 1200m(47.24 in.) x 1100mm (43.31 in.) x 1200mm (47.24 in.)
1 1992 (78.43) 2092 (82.36) 2280 (89.76) 2393 (94.21)
2 319 (12.54) 421 (16.57)
3 1066 (41.97) 1434 (56.46)
4 1087 (42.79) 1456 (57.32)
5 610 (24.02) 809 (31.85)
6 148° maximum door swing, 3 places
Table 3.1 Clearance Distances
Vertiv | VR Installer/User Guide | 12
4 INSTALLATION AND ASSEMBLY PROCEDURES
Once your rack is in its final location, refer to the following procedures to install accessories, adjust
components, and load equipment into the rack.
The following tools ship with the rack for installation assembly:
•cage-nut install tool
•T30 extension drive
4.1 Removing and Reversing Doors
Rack doors are removable for convenience when installing or maintaining equipment. The front door is
also reversible, so that the single door may be opened in a more convenient direction if the rack is near a
wall or other equipment.
To remove a door:
Doors are supported by two hinges and held in place by gravity. They can be lifted off and reinstalled
without tools.
NOTE: Doors are easier to remove if they are open at a 90° angle to the rack.
To reverse the front door:
1. Disconnect the ground wire that is attached to the door and frame.
2. Lift the door off the rack, the loosen and remove screws from both the top and bottom hinges,
shown in Figure 4.1 on the next page.
3. Remove the hinges and place them on the opposite side of the frame in the slots provided.
4. Reinsert and tighten the screws.
5. Remove the hardware from the door catch and install the catch on the opposite side of the
frame.
6. Flip the door.
The hinge pin assemblies are now at the bottom of the hinge-pin attachment point.
7. Remove the hardware, flip the hinge pin and reinsert it in the hinge-pin attachment point.
Vertiv | VR Installer/User Guide | 13
8. Reattach the hinge pin with hardware.
9. Hang the door on the newly positioned hinges.
10. Reconnect the ground wire to the door and frame.
Figure 4.1 Removing hinges and reversing the door
Item Description
1 Ground-wire connection on frame, same on both sides of frame
2 Screw holes for hinge attachment, same on both sides of frame
3 Hinge
4 Hinge-pin bracket hardware in door, flip when reversing door.
4.2 Reversing the door handle
1. Remove the Phillips-head bolt from the swing-handle retainer on the inside of the door.
2. Tilt the handle outward and lift up to remove it from the door.
3. Remove the Phillips-head cam retaining bolt, rotate the cam 180° and re-install cam retaining
bolt.
Vertiv | VR Installer/User Guide | 14
4. After reversing the door, reinstall the swing handle by sliding downward into door and tilting
inward.
5. Re-install swing-handle retainer and Phillips head bolt.
Figure 4.2 Door handle components
Item Description
1 Retaining bracket for handle
2 Screws
3 Paw spacer
4 Handle paw
5 Paw screw
4.2.1 Operating Door Handle
The door swing handles have been installed at the manufacturer. No additional assembly is required. To
operate the swing handle, lift up at the bottom of the handle then swing the handle to the right to open.
The handle must be kept in this position to close the door. Return the handle to the initial position and
use the key provided to lock the handle. The lock on the side panels will accept the same key.
The swing handles and doors are reversible. See Reversing the door handle.
4.3 Removing and Replacing Side Panels
The rack uses dual split-side panels fashioned from sheet metal. Both panels rest on a frame member and
are secured to the frame by a slam latch. The locking latch makes the panels simple to remove and
replace when installing equipment and performing maintenance.
Vertiv | VR Installer/User Guide | 15
To remove a side panel:
1. To remove a panel, insert the key in the side-panel lock and turn clockwise to unlock it.
2. Press on the latch, lean the panel away from the frame, then lift the panel up and away from the
rack and set it aside, see Figure 4.3 below.
3. Repeat steps for other panels being removed.
NOTE: Do not remove the protective-earth bonding clip from the side panels. If the clip is missing,
contact your Vertiv sales representative for instruction on how to proceed.
NOTE: Do not leave the side panel off of the rack for extended periods of time. Always inspect the
channel and remove debris or contaminates before installing the side panel. The ground-bond path
requires a solid metal to metal contact between the panel clip and the enclosure rail.
To replace a side panel:
NOTE: Before replacing a side panel, Make sure there is free area and clearance to reinstall the side
panel and that the ground clip is properly engaged in side panel and frame.
1. Set the bottom of the panel onto the frame member.
2. Move the top of the panel toward the rack and slam the latch.
3. Turn the key counterclockwise until the latching mechanism engages to lock the panel in
place.
4. Repeat steps for other panels being replaced.
Figure 4.3 Removing side panel
Item Description
1 Lean panel away from frame.
2 Lift up and away, then set aside.
Vertiv | VR Installer/User Guide | 16
4.4 Removing and Replacing the Top Panel
The rack uses a tool-less, removable top panel for simple removal and replacement.
To remove the top panel:
1. Pull the pin located in the front of the rack.
2. Lift the front of the top panel, then pull the panel away from the frame member and set it aside.
Figure 4.4 Removing the top panel
Item Description
1 Lift the front of the panel.
2 Pull the panel away from frame, then set aside.
Vertiv | VR Installer/User Guide | 17
4.5 Installing the Edge Guard
1. Press edge guard to the top-cover cut outs by pressing along the edge of the cut out opening
as shown in the following figure.
2. Trim excess edge guard with a pair of scissors after the edge guard after completely applied
around the opening.
3. Repeat steps 1and 2for remaining cut outs.
Figure 4.5 Applying the edge guard
Item Description
1 edge guard
2 Break-away tabs to accommodate the pass-through of large-diameter rack-PDU plugs
4.6 Positioning and Attaching Front-andRear-Mount19-in.EIARails
Front- and rear-mount, 19-in., EIA rails are installed in racks at the factory at 29.13in.(740mm). They
attach to the rack frame at the top, bottom, and in the center using M6x12 Torx-head screws into a rail-
adjustment bracket.
The EIA rails use universal (M6)cage nuts and are marked with rack-mount units (RU) on the front and
rear, see Figure 4.6 on the facing page. The rails also include accessory-mounting holes (AMH), cable
pass-through holes, and cable tie-down slots.
Vertiv | VR Installer/User Guide | 18
Figure 4.6 EIA-rail Features
Item Description
1 Cable-accessory mounting locations
2 U-mark label
3 Cable-trough and air-flow brush-strip attachment (on 800W models only)
4 Cable pass-through cut-out (on 800W models only)
Vertiv | VR Installer/User Guide | 19
To position the EIA rails in the rack:
CAUTION: Do not attempt to adjust rail position after equipment is loaded.
1. Determine the installation location of the EIA rails. See Figure 4.7 below, for available depth of
position in the rack.
Figure 4.7 EIA rail spacing in the rack
Depth
Item 1100 mm (43.31 in.) 1200 mm (47.24 in.)
1 982 mm (38.64 in.) 1082 mm (42.6 in.)
2 854 mm (33.62 in.) 954 mm (37.56 in.)
3 740 mm (29.11)
4 EIA rails
5 PDUbracket
2. Loosen the M6x12 screws in the rail-adjustment brackets that secure the EIA rails to the frame
member, see Figure 4.8 on the facing page.
NOTE: Rails are attached at the top, center and bottom.
3. Slide the rail-adjustment brackets down.
4. Slide the EIA rail to the desired position, making sure to keep it square. The frame member and
support have a feature pattern spaced on 6.35-mm centers to help properly position the rails.
NOTE: The front and rear 19-in. EIA rails must be kept at a 90-degree angle to the upper and lower
frame members. The left- and right-front vertical rails must be the same distance from the front of the
rack. The left- and right-rear vertical rails must be the same distance from the rear of the rack. If these
conditions are not met, equipment and optional features will be difficult to install.
Vertiv | VR Installer/User Guide | 20
5. Hold the rail in position, then install the M6x12 screws into the rail-adjustment brackets.
6. Repeat steps 2to 5for each rail.
Figure 4.8 EIA rail-adjustment components in rack
Item Description
1 Face of EIA rail
2 Rail-adjustment screw
3 EIA rail-alignment features on all frame members
4 Frame member
Vertiv | VR Installer/User Guide | 21
4.7 Mounting Power Distribution Units
Power distribution units may be mounted on the rails or attached to mounting brackets in the rack. Two
PDU mounting brackets are standard in each rack. They are mounted in the rear of the rack, one on each
side.
4.7.1 Installing and Positioning a Full-height PDU/Cable-Management Bracket
The top and bottom of the 4-in. wide brackets are identical for use on either side of the rack. Figure 4.10
on the facing page, shows the mounting and cable-management features of the bracket.
To install a full-height bracket:
1. Position the full-height bracket for installation with the inside bottom flange of the PDU resting
on the flange of the frame member at the top and bottom. See the flange in Figure 4.9 below.
2. Hold the PDU bracket in place, then insert and tighten the screws.
Figure 4.9 Full-height bracket end
Item Description
1 Bracket clip
2 Bracket flange
Vertiv | VR Installer/User Guide | 22
To reposition a full-height bracket:
1. Loosen the screws in the top and bottom PDU hanging bracket.
2. Slide the bracket along the frame member to the desired location and tighten the screws.
To remove a full-height bracket:
1. Loosen the screws in the top and bottom PDU hanging bracket.
2. Lift the bracket up until the hanging bracket clears the frame member and remove the
bracket from the rack.
Figure 4.10 PDU-bracket Features
Item Description
1 Velcro or cable-tie features
2 Tool-less accessory mounting holes
3 Tool-less accessory mounting holes
4 Rack-PDUmounting keyholes
4.8 Baying the Racks
Two or more racks of the same height can be bayed with the supplied baying brackets. The brackets have
three hole locations (shown in 4.8 above):
•The single hole connects to the rack
•The outer holes bay the racks on 24in.(609.6mm) centers for floor-tile placement. When
bayed on 24-in. centers, there is a gap between the frames that must be sealed with a baying-
gasket kit, part VRA5003, to maintain proper airflow.
•The center holes put the racks on metric centers.
Connecting the racks is easier if they are in their final installation position before baying.
WARNING! The rack-baying brackets and hardware are not a ground-bond method. For more
details on properly grounding, see Grounding the Rack on page 25.
Vertiv | VR Installer/User Guide | 23
NOTE: The kit is for 24-in. wide spacing only.
When baying racks together on 24-in. centers, use a Baying Gasket Kit (part VRA5003) to seal the gap
between the racks to maintain proper hot-aisle/cold-aisle best practices. The gasket must be installed
before baying racks.
To install the gasket:
1. Measure and cut gasket to length.
2. peel adhesive backing from the gasket, and place the gasket around side perimeter of one of
the racks.
3. Position the racks next to each other with the gasket between them.
The racks are ready for baying.
Figure 4.11 Baying gasket location
Vertiv | VR Installer/User Guide | 24
To install the racks in a bay configuration:
1. Place racks in a row and open or remove doors for easy access to frame holes.
2. Decide spacing between rack centers, 24in. or 600mm, which determines the screw holes
used in the bracket, see the following figure.
3. Install 2 brackets at front and 2 at rear per the rack's mating planes, as shown in the figure.
Figure 4.12 Installing baying brackets
Item Description
1 Baying bracket
2 Screw hole for 24-in./32-in. centers
3 Screw hole for 600-mm/800-mm centers
4 Screw hole for cabinet connection
4.9 Grounding the Rack
WARNING! Each rack must have its own protective-earth conductor. Do not daisy-chain the
protective-earth circuit using the multiple protective-earthing connection points. Protective-
earthing connections shall be such that disconnection of a protective earth at one point in a
unit or a system does not break the protective-earthing connection to other parts or units in a
system, unless the relevant hazard is removed at the same time.
Each rack shall be connected to the grounding electrode conductor using one of the dedicated
grounding locations, see Figure 4.13 on the next page. Each location is identified with a ground symbol
and has a M8 threaded insert in the frame.
•Install in accordance with national and local electrical codes. Select protective earth grounding
conductor size using the guidance from national and local electrical codes.
•Use a star washer between the ground-terminal fitting and the rack frame to pierce the paint
to provide a good protective-earth-ground circuit. Alternatively, remove paint on the frame
ground-terminal installation location. See NFPA 70 Article 250.
•Torque hardware to 10 N-m (90 lb-in).
Vertiv | VR Installer/User Guide | 25
Figure 4.13 Dedicated grounding locations on the rack frame
4.10 Loading Equipment into the Rack
WARNING! To prevent the rack from tipping over, secure the rack to the floor before installing
equipment.
Once in place at the desired location, install equipment starting in the bottom of the rack with the
heaviest equipment.
Vertiv | VR Installer/User Guide | 26
5 PERIODIC MAINTENANCE
The rack requires no special maintenance. Clean the rack periodically, or more frequently if the air in the
vicinity is not filtered for particulates.
Clean dust from installed equipment according to the manufacturer’s recommendations. Clean the
interior of the rack with a dry cloth.
Vertiv | VR Installer/User Guide | 27
Vertiv | VR Installer/User Guide | 28
This page intentionally left blank.
Vertiv | VR Installer/User Guide
VertivCo.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA
© 2018 Vertiv Co. All rights reserved. Vertiv and the Vertiv logo are trademarks or registered trademarks of Vertiv Co. All other names and logos referred to
are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and
completeness herein, Vertiv Co. assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or
omissions. Specifications are subject to change without notice.
SL-11425_REV3_10-18/590-1859-501D