Vogel's PFW 6831 User Manual
Displayed below is the user manual for PFW 6831 by Vogel's which is a product in the TV Mounts category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
PFW 6831
Display Wall Mount
For use with Panasonic TH-103PF10UK Series 103” Plasma Displays
9531-0028-Z00-01
Page 2 Installation Instructions
Table of Contents
VOGEL’S DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VOGEL’S PRODUCT
FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACH-
MENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR
CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY
SUCH USE, ATTACHMENTS OR MODIFICATIONS.
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING 907 KG IF NOT, THE WALL STRUCTURE MUST BE
REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE
INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL
INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
Warning Statements
Indicates that the power plug is to be disconnected
from the power outlet.
Safety precautions must be taken at all times.
Warning and Caution statements.
In the interest of safety, it is recommended that two to three people, with the aid of an appropriate assisted lifting device, perform this
Warning Statements 2
Parts List 3
Recommended Installation Tools 3
Features 4
Installation Instructions 4
8
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND
COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND
PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE
REFERENCE.
It is recommended that a maximum of 5/8” thick plaster board be used, along with 5/16” lag bolts and washers, when mounting to wooden
studs.
PFW 6831
THIS MOUNT IS NOT RECOMMENDED FOR USE
WITH STEEL STUD WALL STRUCTURES THAT
ARE LESS THAN 10 GAUGE IN THICKNESS ON
THE PROPOSED INSTALLATION WALL.
INSTALL THE DISPLAY ACCORDING TO THE INSTRUCTIONS PROVIDED BY THE DISPLAY MANUFACTURER.
PERFORM ALL STRUCTURAL REINFORCEMENTS BEFORE ATTACHING THE DISPLAY TO THE WALL. USE
THE APPROPRIATE LIFTING DEVICE WHEN LIFTING THE DISPLAY INTO PLACE.
Installation Instructions Page 3
Parts List
This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts
are missing and/or damaged before beginning installation.
Mounting Brackets (Qty 2)Wall Mounting Plates (Qty 2)
Side Straps (Qty 2) m5x.8x12 Phillips Head Screws (Qty 8)
PFW 6831
Spirit Level (Supplied)
Stud Finder
Ladder
1/4” Wood Pilot Drill Bit
3/8” Concrete
Drill Bit For use
with 3/8” concrete
wedge anchors)
Drill
1/2” Socket and Wrench
Pencil
#2 Phillips Screwdriver
Tape Measure
Recommended Installation Tools
5/16” x 3” Lag
Bolts (Qty 16)
5/16” Tri-Lobe Anchor
(Qty 16)
5/16” Flat Washers
(Qty 16)
Page 4 Installation Instructions
Installation Instructions
Ease of Installation
Vogel’s has designed this mount with installer ease-of-installation in mind.
Tilt/Flat Display Orientation
With the PFW 6831, you can mount your display to the wall, or, if you choose, there is a variable tilt feature on the
PFW 6831. This will allow you to tilt your display forward for a more optimized viewing angle.
Side to Side Lateral Shift
Centering the display has never been easier. The PFW 6831 features ±3” built-in side to side lateral shift. This feature will
FOLLOW THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER WHEN LIFTING THE DISPLAY.
PERFORM ALL STRUCTURAL REINFORCEMENTS BEFORE ATTACHING THE DISPLAY TO THE WALL.
USE THE APPROPRIATE LIFTING DEVICE WHEN LIFTING THE DISPLAY INTO PLACE.
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING 907 KG. IF NOT, THE WALL
STRUCTURE MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED
SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE
ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY,
OR EVEN DEATH. USE SUITABLE CONCRETE ANCHORS FOR 3000PSI POURED CONCRETE WALLS.
Step 1. Determine and mark where the ideal viewing center of
the display will be located on the wall.
Step 2. Measure up 24.21” (615.01mm) and mark this location
with a pencil.
STUD CENTER SPACING
16” to 18” - A total of four (4) studs will be used, which
means that you will have a total sixteen (16) mounting points.
Eight (8) will be used for the upper wall plate and eight (8) will be
used for the lower wall plate.
24” - A total of three (3) studs will be used, which means
that you will have a total twelve (12) mounting points. Three (3)
will be used for the upper will plate and three (3) will be used for
the lower wall plate.
Step 3. Using a commercially available stud
place it against the wall, and swing it from left to right,
while engaging the button.
Step 4. When the lights illuminate, or a buzzer sounds, mark that
spot on the wall using a pencil.
Step 5. Repeat Step 2, but this time swing the stud
in from the other side, swinging in from right to
left.
Step 6. When the lights illuminate, or a buzzer sounds,
mark that spot on the wall using a pencil.
Step 7. Now that the edges of the wall stud
have been located, use your tape measure
and determine the center point between
the two marks. This will be center of the
stud. Mark this point with your pencil.
Step 8. Repeat the previous steps to determine the location
of all wall studs.
Mark 1 Mark 2
Stud
Structure
Stud Finder
Stud
Structure
Locating the Stud Center
PFW 6831
Installation Instructions Page 5
A
A
B
B
A - Upper and Lower Wall Plates
B - Side Mounting Brackets
m5x0.8x12 Phillips
Head Screws Level
m5x0.8x12 Phillips
Head Screws
Step 9. Once the center points on all the wood studs have been determined, use a large hanger nail and partially drive it into the wood
stud that will be center-most of the viewing area. The hanger nail will go where the pencil mark was made.
Step 10. Locate the mounting slot closest to center on the upper wall plate (A) and hang the upper wall plate on the hanger nail.
Step 11. Use a spirit level (supplied) to level the upper wall plate. Once the upper wall plate is level, mark the correspondin
g
mounting slots that line up with the studs.
Step 12. Use a commercially available supplied 1/4” pilot drill bit to pre-drill all upper wall plate mounting holes (do not exceed 1/4”
maximum drill bit size).
Step 13. Once the mounting holes have been drilled, attach the upper mounting plate (make sure the open-flange side is pointing up)
using eight (8) 5/16” x 3” lag bolts and eight (8) 5/16” flat washers. Tighten all upper wall plate mounting hardware
and remove the hanger nail.
Step 14. Line up the mounting holes of the side mounting bracket (B) with the mounting holes that are located on the side of the upper
wall plate. Repeat this step for the second side mounting bracket.
Step 15. Use four (4) m5x0.8x12 Phillips heads screws (2 each side for the upper mounting points) to attach the side mountin g
brackets to the upper wall plate. Tighten using a Phillips head screwdriver.
Step 16. After securing the upper side mounting bracket hardware, slide the lower wall plate between the lower side mounting
brackets (reference arrow pointing up; in the event that there is no arrow, make sure the open-flange side is pointing up).
Step 17. While the lower wall plate is held in place, use four (4) m5x0.8x12 Phillips heads screws (2 each side for the lower mounting
points) to attach the side mounting brackets to the lower wall plate. Tighten using a Phillips head screwdriver.
Step 18. Repeat Steps 12 and 13 to mount the lower wall plate. Tighten ALL hardware when complete.
Mounting Slots
Lag Bolts and Washers -
wooden studs only.
For "solid" wall construction
incorporate the use of wedge
anchors supplied with
the lag bolts.
Open Flange
Open Flange
Lag Bolts and Washers -
wooden studs only
PFW 6831
M16 Bolt
Display
Page 6 Installation Instructions
Lock Washer
Step 19. Locate Mounting Bracket A (Qty 2) and Mounting Bracket B (Qty 2).
Step 20. Locate the four (4) M16 hex head bolts and lock washers on the back of the display and remove them (place this hardware to
the side as they will be used again).
Step 21. Align the mounting bracket holes on Mounting Bracket A with the mounting holes on the back of the display. Two
mounting holes will used on each side of the display.
Step 22. Place the lock washers between the display and the mounting brackets.
Step 23. Insert the M16 hex head bolts through the mounting bracket, then through the lock washer and into the display.
Step 24. Tighten the bolt and repeat Steps 20 and 21 for the remaining three bolts. Tighten all hardware.
DO NOT OVERTIGHTEN THE HARDWARE.
M16 Bolt
M16 Bolt
Lock Washer
Lock Washer
Lock Washer
Mounting
Bracket A
Clevis Pin
Clevis
Spring Clip
Step 25. Place Mounting Bracket B into Mounting Bracket A and
install the clevis pin, flat washer and clevis spring clip
hardware into the lower locations on the mounting bracket.
Step 26. Repeat Step 25 for the remaining mounting bracket.
A - Mounting Bracket A
B - Mounting Bracket B
A
A
B
B
Flat Washer
PFW 6831
RAISE THE DISPLAY TO THE WALL PLATES FOLLOWING THE LIFTING INSTRUCTIONS
PROVIDED BY THE DISPLAY MANUFACTURER. USE AN APPROPRIATE LIFTING DEVICE
ASSIST WHEN LIFTING THE DISPLAY INTO PLACE.
M8 x 70mm Lateral
Shift Locking Screw
M8 x 70mm Lateral
Shift Locking Screw
Installation Instructions Page 7
M8 x 70mm Lateral
Shift Locking Screw
M8 x 70mm Lateral
Shift Locking Screw Display
PFW 6831
Step 27. Raise the flat panel with the mounting brackets attached and hang the top and bottom hooks over the mounting rods that are on
the upper and lower wall plates.
Step 28. Once the display is attached to the wall, insert four (4) M8 x 70mm lateral shift locking screws. The mounting points for these
screws are located on the top and at the bottom of the mounting brackets.
Step 29. These screws, once tightened down, will prevent the display from sliding side to side. Make any lateral adjustments at this time
and then tighten the lateral shift locking screws down.
Once the display is mounted securely to the wall, the forward tilt must be determined. There are four tilt setting: 1°,
2°, 3° and 4°; the 1° setting will leave the display in a full vertical position). There are four hole settings at the bottom
of each mounting bracket.
Step 30. Determine the forward tilt setting.
Step 31. Insert the clevis pin through the mounting hole.
Step 32. Once the clevis pin is completely through the mounting hole, place the clevis pin flat washer onto the clevis pin and insert the
cotter pin into the clevis pin. Repeat this step for the remaining side.
Page 8 Installation Instructions
Technical Specification
All measurements are in inches(mm).
48.4
(1229.36)
70.33
(1786.38)
8.792
(227.89)
16.00
(406.4)
16.00
(406.4)
16.00
(406.4)
16.00
(406.4)
PFW 6831