Whirlpool AKR 504 IX User Manual
Displayed below is the user manual for AKR 504 IX by Whirlpool which is a product in the Cooker Hoods category. This manual has pages.
Related Manuals
User and maintenance manual
GB
GB1
IMPORTANT SAFETY INSTRUCTIONS
These instructions shall also be available on website: www.whirlpool.eu.
YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT.
This manual and the appliance itself provide important safety warnings, to be read and observed at all
times.
This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves
and others.
All safety warnings are preceded by the attention symbol and the following terms:
indicates a hazardous situation which, if not avoided, will cause
serious injury.
indicates a hazardous situation which, if not avoided, could cause
serious injury.
All safety warnings specify the potential danger/warning to which they refer and indicate how to reduce
the risk of injury, damage and electrical shock resulting from incorrect use of the appliance. Comply with
the following instructions:
• Installation or maintenance must be carried out by a specialized technician, in compliance with the
manufacturer’s instructions and local safety regulations. Do not repair or replace any part of the
appliance unless specifically requested in the user manual.
• The appliance must be disconnected from the power supply before carrying out any installation work.
• Earthing of the appliance is compulsory. (Not necessary for class II hoods identified by the symbol
on the specifications label).
• The power supply cable must be long enough to permit connecting the appliance to the mains socket
outlet.
• Do not pull the power supply cable in order to unplug the appliance.
• The electrical components must no longer be accessible to the user after installation.
• Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
• This appliance may be used by children older than 8 years of age and by persons with reduced physical,
sensory or mental capacities or with inadequate experience and knowledge only if they are supervised
or if they have been taught how to use the appliance in conditions of safety and if they are aware of the
dangers involved. Children must not play with the appliance. Cleaning and maintenance must not be
carried out by children, unless they are supervised by adults.
• Do not repair or replace any part of the appliance unless specifically indicated in the manual. Defective
parts must be replaced using genuine parts. All other maintenance services must be carried out by a
specialized technician.
• Children must be supervised to ensure they do not play with the appliance.
WARNING:
DANGER:
GB2
• When drilling through a wall or the ceiling, pay attention not to damage electric connections and/or
pipes.
• The ventilation ducts must always discharge to the outside.
• Exhaust air must not be vented through a flue used for removal of fumes produced by appliances
burning gas or other fuels, but must have a separate outlet. All national regulations governing
extraction of fumes must be observed.
• If the hood is used together with other appliances operating on gas or other fuels, the negative
pressure in the room must not exceed 4 Pa (4 x 10-5 bar). For this reason, make sure the room is
adequately ventilated.
• The Manufacturer declines any liability for improper use or incorrect setting of the controls.
• Regular cleaning and maintenance is essential to correct functioning and good performance of the
appliance. Frequently clean all encrustations from dirty surfaces to prevent the accumulation of grease.
Regularly clean or replace the filters.
• Never ame cook food (ambé) under the appliance. Using free ames might cause re.
• Do not leave frying pans unattended when frying, as the frying oil may catch re.
• Failure to observe the instructions for cleaning the hood and replacing the filters may result in a fire.
• The fume extractor hood must never be opened without the grease filters installed and it should be
kept under constant supervision.
• Gas appliances must be used under the extractor hood only with pans resting.
• When using more than three gas cooking points, the hood should be operating at power level 2 or
greater. This will eliminate heat congestion in the appliance.
• Before touching the bulbs, first ensure that they are cold.
• Do not use or leave the hood without its lamps correctly installed - risk of electric shock.
• Wear work gloves for all installation and maintenance operations.
• The product is not suitable for outdoor use.
• When the hob is in use, accessible parts of the hood may become hot.
KEEP THIS BOOKLET FOR FUTURE CONSULTATION.
Declaration of conformity
• This appliance has been designed, manufactured and marketed in compliance with:
- safety objectives of the “Low Voltage” Directive 2014/35/EU;
- the ecodesign requirements of european regulations n. n. 66/2014, n. 327/2011, n. 244/2009, n. 245/2009, n. 1194/2012, n. 2015/1428;;
- the protection requirements of Directive “EMC” 2014/30/EU.
Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system.
Energy saving tips
• Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished.
• Increase the speed only in case of large amount of smoke and vapour and use boost speed(s) only in extreme situations.
• Replace the charcoal filter(s) when necessary to maintain a good odour reduction efficiency.
• Clean the grease filter(s) when necessary to maintain a good grease filter efficiency.
• Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.
GB3
After unpacking the appliance, check for any transport damage. In the event of problems, contact the dealer or your nearest After-sales Service. To prevent any
damage, only remove the appliance from its polystyrene foam packaging at the time of installation.
PREPARING FOR INSTALLATION
this is a heavy product; the hood should only be lifted and installed by two or more people.
The minimum distance between the support of the cooking pans on top of the cooker and the bottom of the hood must not be less than 50 cm for electric
cookers and 65 cm for gas or mixed cookers. Before installation also check the minimum distances stated in the manual of the cooker.
If the installation instructions for the cooker specify a greater distance between cooker and hood, this distance must be observed.
ELECTRICAL CONNECTION
Make sure the power voltage specified on the appliance rating plate is the same as the mains voltage.
This information may be found on the inside of the hood, under the grease filter.
Power cable replacement (type H05 VV-F 3 x 0,75 mm²) must be carried out by a qualified electrician. Contact an authorized service centre.
If the hood is fitted with an electric plug, connect the plug to a socket complying with current regulations, located in an accessible place after installation. If no
plug is fitted (direct wiring to the mains), or if the socket is not located in an accessible place, install a standardised double pole power switch that will enable
complete isolation from the mains in case of category III overvoltage conditions, in accordance with installation rules.
If the cable is not fitted with a plug, connect the wires according to the following table:
WARNING:
Disposal of packing
The packing material is 100% recyclable and is marked with the recycle symbol . The various parts of the packing must therefore be disposed of responsibly
and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product.
- The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an
appropriate collection centre for the recycling of electrical and electronic equipment.
Scrapping of household appliances
• This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut
off the power supply cable.
• For further information on the treatment, recovery and recycling of household electrical appliances, contact your competent local authority, the collection
service for household waste or the store where you purchased the appliance.
INSTALLATION
SAFEGUARDING THE ENVIRONMENT
GENERAL RECOMMENDATIONS
Before use
Remove cardboard protection pieces, protective film and adhesive labels from accessories. Check the appliance for any transport damage.
During use
To avoid any damage do not place any weights on the appliance. Do not expose the appliance to atmospheric agents.
Mains voltage
and frequency
Wire connection
220-240 V
50 Hz : yellow/green
N: blue
L: brown
GB4
The appliance does not work:
• Check for the presence of mains electrical power and if the appliance is connected to the electrical supply;
• Turn off the appliance and restart it to see if the fault persists.
The hood's suction level is not sufficient:
• Check the suction speed and adjust as necessary;
• Check that the filters are clean;
• Check the air vents for any obstructions.
The light does not work;
• Check the light bulb and replace if necessary;
• Check that the light bulb has been correctly fitted.
Before calling the After-Sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the "Troubleshooting guide".
2. Switch the appliance off and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-Sales Service.
Always specify:
• A brief description of the fault;
• The exact type and model of the appliance;
• The service number (number after the word "Service" on the rating plate), located on the inside of the appliance. The service number is also indicated on
the guarantee booklet;
• Your full address;
• Your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used and repairs carried out
correctly).
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
- Never use steam cleaning equipment.
- Disconnect the appliance from the power supply.
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean
immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off with a dry cloth.
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the enamel surface.
• Use detergents specifically designed for cleaning the appliance and follow the manufacturer instructions.
IMPORTANT: clean the filters at least monthly to remove any oil or grease residuals.
WARNING
CLEANING
GB5
- Use protective gloves.
- disconnect the appliance from the power supply.
GREASE FILTERS
The metal grease filter has an unlimited life and should be cleaned once a month by hand or in a
dishwasher at low temperature and with a short cycle. Cleaning in a dishwasher may cause discolouring
of the grease filter, but its filtering efficiency is unaffected.
Pull out the handle to remove the filter.
Wash the filter and leave it to dry, proceeding in reverse order to refit it.
REPLACING LAMPS
The hood lighting system is based on LED technology.
The LEDs ensure optimum lighting and last up to ten times longer than conventional lamps but with 90% less energy consumption.
Contact the technical support service for replacement.
ACTIVATED CARBON FILTER (filter hoods only):
The carbon filter must be cleaned once a month in a dishwasher at the highest temperature,
using a normal dishwasher detergent.
It is advisable to clean the filter separately.
After cleaning, reactivate the carbon filter by drying it in the oven at 100°C for 10 minutes.
Change the carbon filter every 3 years.
Fitting the carbon filter:
1. Remove the grease filter.
2. Hook the carbon filter firstly to the metal tab at the back on the hood and then fix it at the
front with the two knobs.
3. Refit the grease filter.
WARNING
MAINTENANCE
GB6
The hood is designed for installation and use in "Extractor version" or in "Filter version".
Note: The model with electric shutter can only be used in "Extractor version" and the exhaust pipe must be connected to a peripheral extraction unit.
Extractor Version
Fumes are extracted and expelled to the outside through an exhaust pipe (not supplied) fixed to the hood exhaust pipe connector.
Depending on the exhaust pipe purchased, provide for suitable fixing to the exhaust pipe connector.
IMPORTANT: If already installed, remove the carbon filter/s.
Filter Version
Air is filtered through the carbon filter/s and recycled into the surrounding environment.
IMPORTANT: check that air recirculation is facilitated.
If the hood does not have a carbon filter/s, order one/them and fit it/them before use.
Install the hood away from very dirty locations, windows, doors and sources of heat.
The hood comes supplied with all the materials required for installation on most walls/ceilings. However, a qualified technician is needed to make sure that the
plugs are suitable for your ceiling.
Adjacent wall units Adjacent wall units
centre line
65 cm (gas or combi cookers)
50 cm (electric cookers)
hob surface
900 mm min (90 cm wide model)
1000 mm min (100 cm wide model)
1200 mm min (120 cm wide model)
MATERIAL SUPPLIED
INSTALLATION - PRELIMINARY ASSEMBLY INSTRUCTIONS
INSTALLATION DIMENSIONS
Hood assembled with motor, lamps and grease filters installed.
• 1 Pre-assembled truss
• Instructions for assembly and use
• 1 electrical cable
• 1 cable clamp
• 1 assembly template
• screws and wall plugs
• magnetic strips
Filter Version only:
• 1 Filter connector with extensions
• assembly screws
GB7
The instructions below, to be carried out in the order in which they are numbered, refer to the figures (with the same step numbers) given on the last pages of
this manual.
1. IMPORTANT: Work out the exact position where the hood is to be installed:
R1 = Middle of installation point and opening for the exhaust pipe.
FRONT = The side at the front of the hood.
LFT: left side of the hood.
RHT: right side of the hood.
N.B.: the same wording appears on numerous drawings to make it easier to understand the assembly instructions.
2. Place the template on the ceiling, taking into account the above-mentioned reference points and making sure the arrows stamped on the template
correspond with the front part of the hood (FRONT). Drill the number of holes of diameter as indicated.
Insert the wall plugs provided.
3. Half-tighten the screws as indicated (at corners), as these will be needed to fix the truss to the hood.
For Extractor Version only: Make an opening in the ceiling for the exhaust pipe.
4. Remove and set aside the screws securing the truss sections.
5. IMPORTANT: Adjust the extension of the truss, bearing in mind the following mathematical formula:
H (cm) = ( X-Y-M)+10.5.
H = Extension of truss to be calculated.
X= Distance from ceiling to hob.
Y= Minimum distance from the hobb to burners on hob ( 65cm gas hobs, 50cm electric hobs).
M = Height of motor unit from hood.
6. Fix the two sections of the truss using the screws as illustrated.
7. For Extractor Version only: fit an exhaust pipe to extract fumes and carry them to the outside.
This pipe must exit through the ceiling at a height as indicated in the drawing.
N.B.: H = Calculated truss extension (see assembly sequence 5).
N.B.: the exhaust pipe is not included in the packaging.
8. Remove the adhesive tape holding the control electronics box to the motor body.
N.B.: the figure is indicative only, the box may be temporarily fixed to other sides of the motor body.
9. Lift the box as shown.
10. Fully tighten the screws fixing the box to the motor body.
11. Slide the power supply cable into its housing.
12. Secure the cable with a cable clamp.
IMPORTANT: It is essential to carry out this operation. in order to avoid accidental disconnection of the cable.
13. Fix the truss to the hood using the screws as shown.
14. IMPORTANT: Attach the hood to the ceiling and fully tighten the screws.
15. IMPORTANT: Insert and tighten 2 screws (1 on each side) - these are OBLIGATORY safety anchors.
16. Fix the exhaust pipe to the connecting ring.
N.B.: the anchor band is not included in the packaging.
Carry out the electrical connection to the mains power supply.
17. For Filter Version only: Attach the deflector.
N.B.: The deflector comes in 3 pieces and must be assembled to size (the deflector must be ordered separately for this model).
18. Depending on the stability of the truss, decide if the upper support bracket should be fitted (with the screws as indicated).
N.B.: If the minimum extension was used, the bracket won't be necessary.
N.B.: We recommend placing the bracket at equal distances from the ceiling and the lower bracket welded to the truss.
19. Cut 2 magnetic strips to size and attach them to the inside of one of the two upper sections of the flue, as shown in the figure.
20. Assemble the upper sections of the flue to cover the truss. Secure the upper flue to the truss using screws, as shown in the figure.
21. Cut 2 magnetic strips to size and attach them to the inside of one of the two lower sections of the flue, as shown in the figure.
22. Assemble the lower sections of the flue to cover the truss.
23. Insert the flues in their seat above the covering hood, complete with the hood itself.
24. Remove the grease filter/s.
25. Secure the lower sections of the flues from inside the hood, using the screws as shown.
INSTALLATION - ASSEMBLY INSTRUCTIONS
GB8
26. For Filter Version only: fit the carbon filter. NB: (the carbon filter must be ordered separately for this model).
27. Install the filter(s) / fill grease.
Check for correct hood operation, referring to the section describing the hood and how to use it.
1. Control panel.
2. Grease filters.
3. Halogen lamps.
4. Telescopic flue.
Control panel
1. Motor ON/OFF
2. Speed selection (increase/decrease)
Indicator lights:
a. running at minimum extraction speed
b. running at medium extraction speed
c. running at maximum extraction speed
d. running at intensive extraction speed
NB = the intensive extraction speed is timed for 5 minutes, after which the motor will revert to medium speed.
3. Light ON/OFF
NB = control backlighting brightness increases when the function is in use.
DESCRIPTION AND USE OF HOOD
12
3
5
4
89
67
10 11
12
13 14
1615
17
18
23
21 22
19 20
26
24 25
27
400011308137 GB
Printed in Italy
09/2018