Whirlpool AKR 689/1 BK User Manual
Displayed below is the user manual for AKR 689/1 BK by Whirlpool which is a product in the Cooker Hoods category. This manual has pages.
Related Manuals
GB User and maintenance manual
EN3
IMPORTANT SAFETY INSTRUCTIONS
These instructions are also available on the website: docs.whirlpool.eu
YOUR SAFETY AND THAT OF OTHERS IS HIGHLY IMPORTANT.
This manual and the appliance itself provide important safety warnings, to be read
and observed at all times.
This is the attention symbol, pertaining to safety, which alerts users to potential
risks to themselves and others.
All safety warnings are preceded by the attention symbol and the following terms:
DANGER:
indicates a hazardous situation which, if not avoided, will
cause serious injury.
WARNING:
indicates a hazardous situation which, if not avoided, could
cause serious injury.
All safety warnings specify the potential danger/warning to which they refer and
indicate how to reduce the risk of injury, damage and electrical shock resulting
from incorrect use of the appliance. Comply with the following instructions:
• Installation or maintenance must be carried out by a specialized technician, in
compliance with the manufacturer’s instructions and local safety regulations. Do
not repair or replace any part of the appliance unless specically requested in
the user manual.
• The appliance must be disconnected from the power supply before carrying out
any installation work.
• Earthing of the appliance is compulsory. (Not necessary for class II hoods
identied by the symbol on the specications label).
• The power supply cable must be long enough to permit connecting the
appliance to the mains socket outlet.
• Do not pull the power supply cable in order to unplug the appliance.
• The electrical components must no longer be accessible to the user after
installation.
• Do not touch the appliance with any wet part of the body and do not operate it
when barefoot.
• This appliance may be used by children older than 8 years of age and by persons
with reduced physical, sensory or mental capacities or with inadequate
experience and knowledge only if they are supervised or if they have been
taught how to use the appliance in conditions of safety and if they are aware of
the dangers involved. Children must not play with the appliance. Cleaning and
maintenance must not be carried out by children, unless they are supervised by
adults.
• Do not repair or replace any part of the appliance unless specically indicated in
the manual. Defective parts must be replaced using genuine parts. All other
maintenance services must be carried out by a specialized technician.
• Children must be supervised to ensure they do not play with the appliance.
• When drilling through a wall or the ceiling, pay attention not to damage electric
connections and/or pipes.
EN4
• The ventilation ducts must always discharge to the outside.
• Exhaust air must not be vented through a ue used for removal of fumes
produced by appliances burning gas or other fuels, but must have a separate
outlet. All national regulations governing extraction of fumes must be observed.
• If the hood is used together with other appliances operating on gas or other
fuels, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar). For
this reason, make sure the room is adequately ventilated.
• The Manufacturer declines any liability for improper use or incorrect setting of
the controls.
• Regular cleaning and maintenance is essential to correct functioning and good
performance of the appliance. Frequently clean all encrustations from dirty
surfaces to prevent the accumulation of grease.
Regularly clean or replace the lters.
• Never ame cook food (ambé) under the appliance. Using free ames might
cause re.
• Do not leave frying pans unattended when frying, as the frying oil may catch re.
• Failure to observe the instructions for cleaning the hood and replacing the lters
may result in a re.
• The fume extractor hood must never be opened without the grease lters
installed and it should be kept under constant supervision.
• Gas appliances must be used under the extractor hood only with pans resting.
• When using more than three gas cooking points, the hood should be operating
at power level 2 or greater. This will eliminate heat congestion in the appliance.
• Before touching the bulbs, rst ensure that they are cold.
• Do not use or leave the hood without its lamps correctly installed - risk of electric
shock.
• Wear work gloves for all installation and maintenance operations.
• The product is not suitable for outdoor use.
• When the hob is in use, accessible parts of the hood may become hot.
• For lamp replacement use only lamp type indicated in the Maintenance/
Replacing lamps section of this manual.
KEEP THIS BOOKLET FOR FUTURE CONSULTATION
Declaration of Conformity
• This appliance has been designed, manufactured and marketed in compliance with:
- safety objectives of the “Low Voltage” Directive 2014/35/EU;
- the ecodesign requirements of european regulations n. 66/2014, n. 327/2011, n. 244/2009, n. 245/2009,
n. 1194/2012, n. 2015/1428;
- the protection requirements of Directive “EMC” 2014/30/EU.
Electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system.
Energy saving tips
• Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is
nished.
• Increase the speed only in case of large amount of smoke and vapour and use boost speed(s) only in extreme
situations.
• Replace the charcoal lter(s) when necessary to maintain a good odour reduction eciency.
• Clean the grease lter(s) when necessary to maintain a good grease lter eciency.
• Use the maximum diameter of the ducting system indicated in this manual to optimize eciency and minimize
noise.
EN5
INSTALLATION
After unpacking the appliance, check for any transport damage. In the event of problems, contact the dealer or your
nearest After-sales Service. To prevent any damage, only remove the appliance from its polystyrene foam packaging at
the time of installation.
PREPARING FOR INSTALLATION
WARNING:
this is a heavy product; the hood should only be lifted and installed by two or more people.
The minimum distance between the support of the cooking pans on top of the cooker and the bottom of the hood must
not be less than 50 cm for electric cookers and 65 cm for gas or mixed cookers. Before installation also check the
minimum distances stated in the manual of the cooker.
If the installation instructions for the cooker specify a greater distance between cooker and hood, this distance must be
observed.
ELECTRICAL CONNECTION
Make sure the power voltage specied on the appliance rating plate is the same as the mains voltage.
This information may be found on the inside of the hood, under the grease lter.
Power cable replacement (type H05 VV-F 3 x 0,75 mm²) must be carried out by a qualied electrician. Contact an
authorized service centre.
If the hood is tted with an electric plug, connect the plug to a socket complying with current regulations, located in an
accessible place after installation. If no plug is tted (direct wiring to the mains), or if the socket is not located in an
accessible place, install a standardised double pole power switch that will enable complete isolation from the mains in
case of category III overvoltage conditions, in accordance with installation rules.
If the cable is not tted with a plug, connect the wires according to the following table:
Mains voltage
and frequency Wire connection
220-240V
50-60Hz
: yellow/green
N : blue
L : brown
GENERAL RECOMMENDATIONS
Before use
Remove cardboard protection pieces, protective lm and adhesive labels from accessories. Check the appliance for any
transport damage.
During use
To avoid any damage do not place any weights on the appliance. Do not expose the appliance to atmospheric agents.
SAFEGUARDING THE ENVIRONMENT
Disposing of packing
The packing material is 100% recyclable and is marked with the recycle symbol . The various parts of the packing
must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste
disposal.
Scrapping the product
- This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE).
- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this
product.
- The symbol on the product or on the accompanying documentation indicates that it should not be treated as
domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic
equipment.
EN6
Scrapping of household appliances
• This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste
disposal regulations. Before scrapping, cut o the power supply cable.
• For further information on the treatment, recovery and recycling of household electrical appliances, contact your
competent local authority, the collection service for household waste or the store where you purchased the appliance.
TROUBLESHOOTING GUIDE
The appliance does not work:
• Check for the presence of mains electrical power and if the appliance is connected to the electrical supply;
• Turn o the appliance and restart it to see if the fault persists.
The hood’s suction level is not sucient:
• Check the suction speed and adjust as necessary;
• Check that the lters are clean;
• Check the air vents for any obstructions.
The light does not work:
• Check the light bulb and replace if necessary;
• Check that the light bulb has been correctly tted.
AFTERSALES SERVICE
Before calling the After-sales Service:
1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide”.
2. Switch the appliance o and back on again it to see if the fault persists.
If after the above checks the fault still occurs, get in touch with the nearest After-Sales Service.
Always specify:
• A brief description of the fault;
• The exact type and model of the appliance;
• The service number (number after the word “Service” on the rating plate), located on the inside of the appliance. The
service number is also indicated on the guarantee booklet;
• Your full address;
• Your telephone number.
If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will
be used and repairs carried out correctly).
CLEANING
WARNING: - Never use steam cleaning equipment.
- Disconnect the appliance from the power supply.
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact
with the appliance, clean immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish
o with a dry cloth.
IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the enamel
surface.
• Use detergents specically designed for cleaning the appliance and follow the manufacturer instructions..
IMPORTANT: clean the lters at least monthly to remove any oil or grease residuals.
EN7
MAINTENANCE
WARNING: - use protective gloves.
- disconnect the appliance from the power supply.
GREASE FILTERS
The metal grease lter has an unlimited life and should be cleaned once a month by hand or
in a dishwasher at low temperature and with a short cycle. Cleaning in a dishwasher may
cause discoloring of the grease lter, but its ltering eciency is unaected.
Pull out the handle to remove the lter.
Wash the lter and leave it to dry, proceeding in reverse order to ret.
REPLACING LAMPS
1. Disconnect the hood from the household power supply.
2. Remove the grease lters.
3. Replace the damaged lamp.
Use E14 2,5W max LED lamps only. For more details, check enclosed leaet “ILCOS D” (alfanumeric position “1e”).
4. Ret the grease lters.
ACTIVATED CARBON FILTER (lter hoods only):
It retains the unpleasant odors produced during cooking.
Change the carbon lter every 4 months.
Fitting or changing the carbon lter
1. Disconnect the hood from the power supply.
2. Remove the grease lters.
3. Fit the lters over the motor.
Make sure the pins R on the manifold match the slots S; turn the lters to secure
them to the pins.
Proceed in reverse order to remove.
Ret the grease lters.AFTER-SALES SERVICE
EN8
MATERIAL SUPPLIED
Remove all the components from the packets. Check that all the components are included.
• Hood assembled with motor, lamps and grease lters installed.
• Instructions for assembly and use
• 1 collar
• 1 Assembly template
• 6 wall plugs Ø 8mm
• 6 screws Ø 5x45
• 6 screws Ø 3 x 9
• 2 screws Ø 3.5 x 9.5
INSTALLATION PRELIMINARY ASSEMBLY INSTRUCTIONS
The hood is designed for installation and use in "Extractor version" or in "Filter version".
Note: The model with electric shutter can only be used in "Extractor version" and the exhaust pipe must be connected to
a peripheral extraction unit.
Extractor Version
Fumes are extracted and expelled to the outside through an exhaust pipe (not supplied) xed to the hood exhaust pipe
connector.
Depending on the exhaust pipe purchased, provide for suitable xing to the exhaust pipe connector.
IMPORTANT: If already installed, remove the carbon lter/s.
Filter Version
Air is ltered through the carbon lter/s and recycled into the surrounding environment.
IMPORTANT: check that air recirculation is facilitated.
If the hood does not have a carbon lter/s, order one/them and t it/them before use.
Install the hood away from very dirty locations, windows, doors and sources of heat.
The hood comes supplied with all the materials required for installation on most walls/ceilings. However, a qualied
technician is needed to make sure that the
plugs are suitable for your ceiling.
INSTALLATION DIMENSIONS
Adjacent wall units 900 mm min (90 cm wide model)
600 mm min (60 cm wide model)
Adjacent wall units
centre line
hob surface
65 cm (gas or combi cookers)
50 cm (electric cookers)
EN9
INSTALLATION ASSEMBLY INSTRUCTIONS
The instructions below, to be carried out in the order in which they are numbered, refer to the gures (with the same step
numbers) given on the last pages of this manual.
1. Mark a line on the wall, up to the ceiling, corresponding to the centre line.
2. Place the drilling template against the wall (x it with adhesive tape): the vertical centre line printed on the template
must match the centre line drawn on the wall, and the bottom edge of the drilling template must match the bottom
edge of the hood. Make the holes indicated on the template.
3. Remove the drilling template and insert plugs and screws as indicated. Tighten a little
4. Place the ue support bracket on the wall, against the ceiling. Drill and insert the wall plugs as shown. Fix the bracket.
5. For Extractor Version only - rear exhaust: Make a hole in the rear wall for the ue pipe.
6. For Extractor Version only - exhaust towards the ceiling: Make a hole in the ceiling for the ue pipe.
7. Prepare the connection to the household electrical system.
8. Remove the grease lter/s.
9. Hook the hood to the wall.
10. Adjust the hood horizontally.
11. Mark the hole/s for nal xing of the hood as indicated.
12. Remove the hood from the wall.
13. Drill as indicated
14. Insert the wall plugs as indicated.
15. Rehook the hood to the wall.
16. Secure the hood to the wall with screws as indicated.
17. For Extractor Version only - Fix the collar to the exhaust outlet hole.
18. Carry out the connection to the household electrical system.
For Extractor Version only - Connect the ue pipe to the collar; the pipe must be run towards the outside (extractor
version) or towards the deector (lter version).
19. Filter Version only: Fix the deector to the bottom ue section.
20. Fit the ues in the special place over the hood.
21. Slide the top section upwards and x the ues with the screws as indicated.
22. Fit the carbon lter (For Filter Version only) and ret the grease lter/s.
Check hood operation, referring to the section giving a description of the hood and its use.
DESCRIPTION AND USE OF HOOD
1. Control panel.
2. Grease lters.
3. Lamps.
4. Telescopic ue.
Control panel
Light : move the switch to the right or press the button to switch on.
Extraction speed/power : move the switch to the right or press the
next button to increase power/speed.
1
3
2
4
5 6
7 8
9 10
11 12
13 14
14 16
18 19
17
20 21
22
400011253889
Printed in Italy
09/2018
GB