Whirlpool AKR 808 MR User Manual
Displayed below is the user manual for AKR 808 MR by Whirlpool which is a product in the Cooker Hoods category. This manual has pages.
Related Manuals
EN User and maintenance manual
EN3
IMPORTANT SAFETY INSTRUCTIONS
These instructions are also available on the website: docs.whirlpool.eu
YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT.
This manual and the appliance itself provide important safety warnings that must be read and heeded at all
times.
This is the safety warning symbol, which alerts users to potential hazards to themselves and others.
All safety messages are preceded by the warning symbol and the following words:
DANGER indicates a hazardous situation which, if not avoided, will cause
serious injury.
WARNING indicates a hazardous situation which, if not avoided, could cause
serious injury.
All safety messages indicate the nature of the potential hazard/warning and how to reduce the risk of injury,
harm and electric shock resulting from improper use of the appliance. Always comply with the following
instructions:
• Installation and maintenance must be carried out by a qualied technician, in compliance with the
manufacturer’s instructions and the local safety regulations. Do not repair or replace any part of the
appliance unless specically stated in the user manual.
• The appliance must be disconnected from the mains before carrying out any kind of installation work.
• It is compulsory to earth the appliance (however, it is not necessary for class II hoods identied by the
symbol on the specications label).
• The power cable must be long enough to connect the appliance to the power supply socket.
• Do not pull on the power cable to unplug the appliance.
• After installation, the electrical components must not be accessible to the user.
• Do not touch the appliance with wet hands and do not operate it when barefoot.
• This appliance may not be used by children (aged 8 and above), persons with any physical, sensory or
mental impairment, or persons lacking experience or knowledge of the appliance, unless they are
supervised or given instruction on how to use it safely and are made aware of the hazards its use might
entail. Children must not play with the appliance. Cleaning and user maintenance must not be carried out
by children unless they are under adult supervision.
• Do not repair or replace any part of the appliance unless specically recommended in the manual. Any
defective parts must be replaced with original spare parts. All other maintenance work must be carried
out by a qualied technician.
• Children must be supervised to ensure that they do not play with the appliance.
• When drilling holes into the wall or ceiling, take care not to damage any electrical wiring and/or
pipework.
• Ventilation ducts must always discharge exhaust air to the outside.
• Exhaust air must not be discharged through a ue used for extracting fumes produced by gas-burning or
any other fuel-burning appliances; it must have a separate outlet. All national exhaust air regulations
must be observed.
EN4
• If the hood is used at the same time as other appliances that use gas or other fuels, the negative pressure
of the room must not exceed 4Pa (4x10-5bar). Please ensure, therefore, that the room is adequately
ventilated.
• The manufacturer does not accept any liability for inappropriate use of the appliance or for incorrect
setting of the controls.
• Regular maintenance and cleaning ensure that the appliance works correctly and achieves optimum
performance. Regularly clean all stubborn surface dirt, to avoid a build-up of grease. Regularly remove
and then clean or replace the lters.
• Failure to observe the instructions for cleaning the hood and cleaning and replacing the lters may result
in a re.
• The extractor hood must never be opened without the grease lters tted and should be regularly
monitored.
• When using the extractor hood above a gas appliance, ensure that any burners in use are covered by a
pan.
• If three or more gas cooking zones are in use, the hood should be set at power setting 2 or higher. This
prevents the build-up of excess heat in the appliance.
• Before touching any lamps, ensure that they are cold.
• The hood must not be used or left without properly tted lamps, as this may cause electric shock.
• Wear protective gloves when carrying out any installation and maintenance work.
• This product is not suitable for outdoor use.
• When the hob is in use, accessible parts of the hood may become hot.
KEEP THESE INSTRUCTIONS
EN5
Declaration of Conformity
• This product has been designed, manufactured and marketed in compliance with:
-the ecodesign requirements of European Regulations n. 66/2014, n. 327/2011, n. 244/2009, n. 245/2009, n. 1194/2012, n. 2015/1428.
The appliance's electrical safety can only be guaranteed if it is correctly connected to an approved earthing system.
Energy saving tips
• Switch on the hood at the lowest speed setting when you start cooking and allow it to run for a few minutes after you have nished cooking.
• Only increase the speed if there is a lot of smoke or steam and only use the "Boost" setting(s) in extreme situations.
• Replace the carbon lter(s) when necessary, to maintain ecient odour reduction.
• Clean the grease lter(s) when necessary, to maintain eciency.
• Use a pipe with the maximum diameter specied in this manual, to optimise eciency and reduce noise levels to a minimum.
INSTALLATION
After unpacking the appliance, check that it has not been damaged in transit. In the event of problems, contact the dealer or your nearest After-sales Service. To
prevent any damage, only remove the appliance from its polystyrene base at the time of installation.
PREPARING FOR INSTALLATION
WARNING this appliance is heavy; the hood must be lifted and installed by two or more people.
The minimum distance between the pan support on the hob and the bottom of the hood must be no less than 40 cm for electric hobs and 65cm for gas or mixed
hobs.
Before installation, also check the minimum distances specied in the hob manual.
If the installation instructions for the hob specify a greater distance between the hob and the hood, this distance must be observed.
ELECTRICAL CONNECTION
Check that the voltage specied on the appliance identication plate is the same as the mains voltage.
This information is found on the inside of the hood, under the grease lter.
The power cable (type H05VV-F 3x0.75mm2) must only be replaced by an authorised electrician. Contact an authorised Service Centre.
If the hood is tted with an electric plug, connect the appliance to a socket which complies with current regulations and which is in an accessible location. If no plug
is tted (direct wiring to the mains), or if the socket is not in an accessible location, install a standardised two-pole circuit breaker that will allow complete isolation
from the mains in the event of category III overvoltage, in compliance with the wiring regulations.
If the cable is not tted with a plug, connect the wires according to the following table:
Mains voltage and
frequency Wire connection
220-240V – 50Hz : yellow/green
N : blue
L : brown
GENERAL RECOMMENDATIONS
Before use
Remove any protective cardboard, transparent lm and adhesive labels from the accessories. Check whether the appliance has been damaged in transit.
During use
Do not place heavy items on the appliance as this may cause damage. Do not expose the appliance to atmospheric agents.
EN6
SAFEGUARDING THE ENVIRONMENT
Disposing of packaging material
The packaging material is 100% recyclable and is marked with the recycling symbol ( ). Do not dispose of the various packaging carelessly, but do so
responsibly and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
-This appliance is marked in compliance with European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).
-By ensuring that this product is disposed of correctly, you will help prevent potentially negative consequences for the environment and human health.
-The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an
appropriate collection centre for the recycling of electrical and electronic equipment.
Scrapping household appliances
• This appliance is manufactured using recyclable or reusable materials. Scrap the appliance in accordance with local regulations on waste disposal. Before
scrapping, cut o the power cable so that the appliance cannot be connected to the mains.
• For further information on the treatment, recovery and recycling of household appliances, contact the competent local authority, the domestic waste
collection service or the shop where you purchased the product.
TROUBLESHOOTING GUIDE
The appliance does not work:
• Check the mains voltage and whether the appliance is connected to the power supply;
• switch the appliance o and on again to see if the fault persists.
The hood is not extracting air suciently:
• Check that the air extraction speed is set to the desired level;
• Check that the lters are clean;
• Check the air vents for any obstructions.
The lamp does not work:
• Check the bulb and replace if necessary;
• Check that the bulb has been tted correctly.
AFTER-SALES SERVICE
Before calling the After-sales Service:
1. Check whether you can solve the problem yourself by following the suggestions given in the “Troubleshooting guide”.
2. Switch the appliance o and on again to see if the fault persists.
If the fault persists after carrying out the above checks, contact the nearest After-sales Service.
Always provide:
• A brief description of the fault;
• The type and exact model of the appliance;
• The Service number (the number after the word "SERVICE" on the identication plate), located on the inside of the appliance. The Service number is also stated
in the warranty booklet;
• Your full address;
• Your telephone number;
If any repairs are required, please contact an authorised After-sales Service Centre (to ensure that original spare parts are used and repairs are carried out correctly).
EN7
CLEANING
WARNING -Do not use steam-cleaning equipment.
- Disconnect the appliance from the mains.
IMPORTANT: Do not use corrosive or abrasive detergents. If any such products unintentionally come into contact with the appliance, clean the
appliance immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing-up detergent to the water. Finish o with a dry cloth.
IMPORTANT: Do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the enamel surfaces.
• Use detergents specically designed for cleaning the appliance and follow the manufacturer's instructions.
IMPORTANT: Clean the lters at least once a month to remove oil and grease residue.
MAINTENANCE
WARNING -Wear protective gloves.
- Disconnect the appliance from the mains.
GREASE FILTERS
The metal grease lter has an unlimited service life and must be washed once a month by hand or in a dishwasher at low
temperatures on a short cycle. Cleaning in a dishwasher may cause discolouration of the grease lter, but its ltering
eciency is unaected.
Open the extractor panel (turn upwards).
Please note: It is not necessary to remove the panel.
Pull out the handle to remove the lter.
Once the lter has been washed and left to dry, proceed in reverse order to ret the lter.
CARBON FILTER (for ltration models only)
This lter retains the unpleasant odours produced during cooking.
Replace the carbon lter every 4 months.
Fitting or replacing the carbon lter
1. Disconnect the hood from the mains.
2. Open and remove the extractor panel from its housing.
3. Remove the grease lters.
4. Fit one carbon lter on each side, covering both protective grilles for the motor impeller.
Turn the lters clockwise to secure them to the central pins.
Proceed in reverse order to remove.
Ret the grease lters and extractor panel.
Maintenance of the condensation pan
The inspection window at the front of the condensation collection pan allows you to check if the pan is full, or being
drained or cleaned.
In any event, the pan must be drained and cleaned AT LEAST once a week, or more frequently, based on the level of usage
of the hood.
The pan can be cleaned by hand or in a dishwasher at low temperatures on a short cycle.
EN8
REPLACING THE LAMPS
The hood is equipped with an LED lighting system.
LEDs ensure excellent illumination, have a service life up to 10 times longer than traditional bulbs, and oer up to 90%
energy savings.
To replace a lamp, proceed as follows:
1. Remove the grease lters.
2. Access the lamps from inside the hood.
3. Press the release clips to release the lamp.
4. Remove the lamp from the hood frame.
5. Disconnect the terminal.
Proceed in reverse order to t the replacement lamp.
NB: To purchase an LED lamp, please contact the Technical After-sales Service Centre.
MATERIALS SUPPLIED
Remove all the components from the packages. Check that all the components are included.
• Assembled hood with motor, bulbs and grease lters tted (1 or 2 grease lters depending on the model).
• Installation and operating instructions
• 1 x mounting template
• 1 x Torx T10 adapter
• 1 x Torx T20 adapter
• 1 x deector
• 5 x wall plugs, dia. 8 mm
• 5 x screws dia. 5x45
• 3 x screws dia. 3.5x9.5
• 1 x washer dia. 5.3x2
• 1 x cable clamp
• Power cable
• 2 x deectors
• 1 x telescopic chimney section
• 1 x chimney support bracket
INSTALLATION – PRELIMINARY FITTING INSTRUCTIONS
The hood is designed for installation in "lter mode".
Filter mode
The air is ltered as it passes through one or more carbon lters and is recycled back into the atmosphere.
IMPORTANT: Check that the air recirculation process runs smoothly.
If the hood does not have the carbon lter(s), order one/them and t before use.
The hood must be tted away from very dirty areas, windows, doors and sources of heat.
The hood comes with all the materials necessary for installation on the majority of walls/ceilings. However, a qualied technician must ensure that the materials are
suitable for the type of wall/ceiling in question.
INSTALLATION DIMENSIONS
Side units Side units
min. 880 mm
Central line
65 cm (gas or mixed stoves)
40 cm (electric stoves) Hob surfaces
EN9
INSTALLATION – FITTING INSTRUCTIONS
The instructions below, to be carried out in the order in which they are numbered, refer to the drawings on the last few pages of this manual, which are marked with
the corresponding numbers.
IMPORTANT: The hood is supplied in 'extractor mode'.
To use the hood in 'lter mode', the carbon lter must be purchased and tted after installation.
For 'extractor mode' only: The hood is supplied with an upper exhaust outlet. If necessary, the outlet can be routed through the wall (see installation instructions).
1. Mark a vertical centre line on the wall, as far as the ceiling.
2. Place the drilling diagram against the wall (hold it in place with adhesive tape). The vertical centre line printed on the drilling diagram must match the centre
line drawn on the wall.
Please note: The bottom edge of the drilling diagram corresponds to the bottom edge of the hood.
IMPORTANT: the bottom edge of the drilling diagram must be a minimum distance of 40cm (for electric hobs) or 65 cm (for gas hobs) from the
surface of the hob.
3. Drill the holes as indicated on the drawing.
4. For 'extractor mode' only – rear outlet: Make a hole in the wall for the exhaust pipe.
5. Remove the drilling diagram from the wall, insert the two wall plugs and two screws in the upper holes in the wall, making sure that they protrude by around
5mm; insert the third wall plug in the bottom hole.
6. If you want to install the chimney section: Attach the chimney support bracket to the wall. Drill a hole and insert the wall plugs as shown. Fix the bracket in
place.
7. Only for 'lter mode' with chimney: Fit the lter connector to the chimney support bracket.
8. Only for 'lter mode' without chimney: Fit the plastic grille to the air outlet hole on the hood.
9. For 'extractor mode' only – upper outlet: Install the non-return exhaust valve.
10. Open the panel and remove the grease lter.
11. For 'extractor mode' only – rear outlet: Remove the pre-fractured cap located on the back panel of the hood, taking care not to damage it.
12. For 'extractor mode' only – rear outlet: Remove the electronic box, unscrewing the two screws that x it to the motor unit, and unhooking it from the pins on
the opposite side (keep the screws).
13. For 'extractor mode' only – rear outlet: Remove the screws that x the motor unit to the hood (keep the screws).
14. For 'extractor mode' only – rear outlet: Rotate the motor unit.
15. Fix the electronic box using the previously removed screws (see installation sequence 12).
16. For 'extractor mode' only – rear outlet: Fix the motor unit to the back panel of the hood using the previously removed screws (see installation sequence 13).
17. For 'extractor mode' only – rear outlet: Fit the previously removed cap (see installation sequence 11) using two screws, as shown.
18. Hook the rear holes in the hood over the retaining screws.
19. Insert the washer and safety screw in the lower hole. Secure the hood to the wall by tightening the two xing screws.
20. Insert the power cable in the appropriate slot. Secure the cable with the cable clamp.
IMPORTANT: This action is compulsory. It will prevent accidental disconnection of the power cable.
Connect the appliance to the household mains.
21. Fit the carbon lters, covering the motor. Turn the lters to secure them to the central pins.
22. Re-t the grease lters and close the panel.
23. If you want to install the chimney section: Rest the chimney on top of the hood, remove the top section and x the chimney using two screws, as shown.
Check that the hood is working properly, referring to the section on the description and use of the hood.
EN10
DESCRIPTION AND USE OF THE HOOD
1. Control panel
2. Extractor panel
3. Grease lter (behind the panel)
4. LED lamps
Control panel
For selecting hood functions with a simple tap of the command button.
AKR 809 MR – AKR 808 MR – AKR 809 UK MR
AKR 808 BK – AKR 808 UK BK
T1. Motor ON/OFF button (stand by) – resets the lter saturation indicators
T2. ON button – speed selection (extraction power) for low speed
T3. Speed selection button (extraction power) for normal speed
T4. Speed selection button (extraction power) for high speed and Intensive setting.
Press to activate high speed (extraction power).
Press again to activate the Intensive speed setting (extraction power) (button ashes for 5 minutes, after which it returns to normal speed (extraction power).
T5. "Anti-condensation function" ON/OFF button: Prevents condensation from forming on the surface of the hood. Activate as required.
"Automatic anti-condensation function": The hood activates this function each time the hood is switched on.
Automatic ON/OFF activation: With the hood switched o, press and hold the button (for around 3 seconds until a "beep" signal sounds) to activate or
deactivate this function.
Please note: The anti-condensation function must only be activated when the motor is switched on.
Warning! Even if this function is never activated, carry out periodic maintenance of the condensation pan all the same, as indicated in the
"Maintenance – Cleaning – Maintenance of the condensation pan" section.
T6. Light ON/OFF button.
EN11
Filter saturation indicators
At regular intervals, the hood signals the need to perform lter maintenance.
Please note: The indicators are activated when the hood is switched on.
Flashing T2 button: Carry out maintenance on the grease lter.
Flashing T3 button: Carry out maintenance of the active carbon lter.
Please note: The lter saturation signal is visible within the rst minute after the hood has been switched o; after this time, the saturation indicators are reset.
Filter saturation indicator reset:
Please note: This action is carried out with the hood switched on.
Press and hold the T1 button.
Active carbon lter saturation indicator activated
Please note: This action is carried out with the hood switched o.
This indicator is usually deactivated; simultaneously press and hold the T2 and T3 buttons to activate the function: The T3 button lights up to indicate activation.
To deactivate the function, simultaneously press and hold the T2 and T3 buttons: The T3 button ashes briey and then goes out to indicate deactivation.
EN12
EN13
EN14
EN15
EN16
EN17
EN18
EN19
EN20
EN21
EN22
EN23
EN24
400011169562