Whirlpool WCT 64 FLS X User Manual
Displayed below is the user manual for WCT 64 FLS X by Whirlpool which is a product in the Cooker Hoods category. This manual has pages.
Related Manuals
EN
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT
In order to receive a more complete assistance, please
register your product on www . whirlpool . eu/ register
Before using the appliance carefully read the Safety
Instruction.
PRODUCT DESCRIPTION
FIRST TIME USE
AIR VENT (FOR THE SUCTION VERSIONS)
Connect the hood and discharge holes on the walls with a diameter
equivalent to the air outlet (connection ange).
Using the tubes and discharge holes on walls with smaller dimensions
will cause a diminution of the suction performance and a drastic
increase in noise.
Any responsibility in the matter is therefore declined.
!Use a duct of the minimum indispensible length.
!Use a duct with as few elbows as possible (maximum elbow angle: 90°).
!Avoid drastic changes in the duct cross-section.
!The company declines any responsibility whenever these regulations
are not respected.
FILTERING OR DUCTING?
!Your cooker hood is ready to be used in suction version.
To use the hood in ltering version the special ACCESSORY KIT must be
installed.
Check if the ACCESSORY KIT is furnished or must be bought separately.
Note: If furnished, in certain cases, the additional activated carbon ltering
system may be installed on the hood. Information about the conversion of
the hood from suction version to ltering version is present in the Manual
“Safety Instructions & Installation”.
DUCTING VERSION
In this case the fumes are conveyed outside of the building by means
of a special pipe connected with the connection ring located on top of
the hood.
Attention! The exhausting pipe is not supplied and must be purchased
apart. Diameter of the exhausting pipe must be equal to that of the
connection ring.
Attention! If the hood is supplied with active charcoal lter, then it
must be removed.
FILTER VERSION
The aspirated air will be degreased and deodorised before being fed
back into the room.
In order to use the hood in this version, you have to install a system of
additional ltering based on activated charcoal.
CONTROL PANEL
The hood is tted with a control panel with aspiration speed selection
control and a light switch to control cooking area lights.
a. ON/OFF lighting
b. OFF motors
c. - d. - e. Minimum suction power (c.), medium (d.), maximum (e.).
TECHNICAL DATA
Height (cm) Width (cm) Depht (cm) Ø of exaust tube (cm)
17. 2 49.3 - 69.3 25.7 12. 5
* Available only on certain models
CLEANING AND MAINTENANCE
CLEANING
• Do not use steam-cleaning equipment.
• Disconnect the appliance from the mains.
Important: do not use corrosive or abrasive detergents. If any such
products unintentionally come into contact with the appliance, clean
the appliance immediately with a damp cloth. Do not use alcohol.
• Clean the surfaces with a damp cloth. If it is very dirty, add a few
drops of washing-up detergent to the water. Finish o with a dry
cloth.
Important: do not use abrasive sponges or metallic scrapers or
scourers. Over time, these can ruin the enamel surfaces.
• Use detergents specically designed for cleaning the appliance
and follow the manufacturer's instructions.
Important: clean the lters at least once a month to remove oil and
grease residue.
MAINTENANCE OF THE GREASE FILTERS
This must be cleaned once a month using non aggressive detergents,
either by hand or in the dishwasher, which must be set to a low
temperature and a short cycle.
When washed in a dishwasher, the grease lter may discolour slightly,
but this does not aect its ltering capacity.
Pull out the handle to remove the lter.
Once the lter has been washed and left to dry, proceed in reverse
order to ret the lter.
MAINTENANCE OF THE CHARCOAL FILTER
(FOR FILTRATION MODELS ONLY)
This lter retains the unpleasant odours produced during cooking.
Saturation of the carbon lter occurs after a relatively long use,
however this depends on the type of cooking and how regularly
the grease lter is cleaned. Regardless, it is necessary to replace the
cartridge every 4 months. It CANNOT be washed or recycled.
Fitting or replacing the carbon lter
1. Disconnect the hood from the mains.
2. Remove the grease lters.
3. Fit 2 carchoal lters (one each side of the conveyour), snap into
place.
4. Reinstall the grease lter in place.
Proceed in reverse order to remove.
REPLACING THE LAMPS
Disconnect the appliance from the electricity.
Prior to touching the light bulbs ensure they are cooled down.
Remove the grease lters to access the lamp area.
Replace the damaged lamp.
Use E14 3W max LED lamps only. For more details, check enclosed
leaet “ILCOS D” (alfanumeric position “1d”).
Note: For replacement LED, please contact the Technical After-sales Service
Centre.
TROUBLESHOOTING
Problem Solutions
The appliance does not work. • Check the mains voltage and whether the appliance is connected to the power supply;
• Check that a speed has been selected;
• Switch the appliance o and on again to see if the fault persists.
The hood is not extracting air suciently. • Check that the air extraction speed is set to the desired level;
• Check that the lters are clean;
• Check the air vents for any obstructions.
The hood has turned o during normal
functioning.
• Check that the power has not been disconnected;
• Check that the omnipolar disconnection device has not tripped.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website docs . whirlpool . eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty
booklet). When contacting our After-sales Service, please state the codes provided on
your product's identication plate.
XXXXXXXXXXXXXX
Model
xxxxxxxxxxxx
XXXXXXXXXXXXXX
Model
xxxxxxxxxxxx
400011261686
* Available only on certain models