Table of Contents
- Alienware Aurora Ryzen Edition R14 Service Manual
- Contents
- Working inside your computer
- Removing and installing components
- Inside view of your computer
- System-board components
- Recommended tools
- Screw list
- Cable cover
- Left-side cover
- Top cover
- Right-side cover
- Front bezel
- Side light
- 2.5-inch hard drive
- 3.5-inch hard drive
- Power-supply unit
- Coin-cell battery
- Memory modules
- Single-graphics card
- Solid-state drive
- Top bezel
- Processor fan and heat-sink assembly
- Processor liquid-cooling assembly
- Processor
- Wireless card
- Antennas
- Front-chassis fan
- PCIe fan
- Top-chassis fan
- Front AlienFX LED boards
- Power-button board
- VR heat sinks
- System board
- Device drivers
- System setup
- Troubleshooting
- Getting help and contacting Alienware
Alienware Aurora R14 User Manual
Displayed below is the user manual for Aurora R14 by Alienware which is a product in the PCs/Workstations category. This manual has pages.
Related Manuals
Alienware Aurora Ryzen Edition R14
Service Manual
Regulatory Model: D30M
Regulatory Type: D30M003
October 2021
Rev. A01
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
Contents
Chapter 1: Working inside your computer..............................................................................................6
Before working inside your computer.................................................................................................................................6
Safety instructions.................................................................................................................................................................6
Safety precautions................................................................................................................................................................ 7
Electrostatic discharge—ESD protection............................................................................................................................7
ESD field service kit .............................................................................................................................................................8
Transporting sensitive components......................................................................................................................................9
After working inside your computer....................................................................................................................................9
Chapter 2: Removing and installing components..................................................................................10
Inside view of your computer.............................................................................................................................................10
System-board components................................................................................................................................................. 11
Recommended tools........................................................................................................................................................... 12
Screw list..............................................................................................................................................................................12
Cable cover......................................................................................................................................................................... 13
Removing the cable cover.............................................................................................................................................13
Installing the cable cover.............................................................................................................................................. 14
Left-side cover....................................................................................................................................................................15
Removing the left-side cover........................................................................................................................................15
Installing the left-side cover......................................................................................................................................... 16
Top cover.............................................................................................................................................................................17
Removing the top cover................................................................................................................................................ 17
Installing the top cover..................................................................................................................................................19
Right-side cover..................................................................................................................................................................19
Removing the right-side cover..................................................................................................................................... 19
Installing the right-side cover...................................................................................................................................... 20
Front bezel ......................................................................................................................................................................... 21
Removing the front bezel..............................................................................................................................................21
Installing the front bezel...............................................................................................................................................22
Side light.............................................................................................................................................................................24
Removing the Side light............................................................................................................................................... 24
Installing the Side light................................................................................................................................................. 25
2.5-inch hard drive............................................................................................................................................................ 26
Removing the 2.5-inch hard drive...............................................................................................................................26
Installing the 2.5-inch hard drive.................................................................................................................................27
Identifying the storage device in Device Manager.....................................................................................................29
Identifying the storage device in system setup (BIOS)...............................................................................................29
3.5-inch hard drive............................................................................................................................................................ 29
Removing the 3.5-inch hard drive...............................................................................................................................29
Installing the 3.5-inch hard drive..................................................................................................................................31
Power-supply unit.............................................................................................................................................................. 33
Removing the power-supply unit.................................................................................................................................33
Installing the power-supply unit...................................................................................................................................35
Coin-cell battery.................................................................................................................................................................37
Removing the coin-cell battery.................................................................................................................................... 37
3
Installing the coin-cell battery......................................................................................................................................38
Memory modules................................................................................................................................................................ 38
Removing the memory modules................................................................................................................................... 38
Installing the memory modules..................................................................................................................................... 39
Single-graphics card..........................................................................................................................................................40
Removing the single-graphics card............................................................................................................................. 40
Installing the single-graphics card............................................................................................................................... 42
Solid-state drive.................................................................................................................................................................44
Removing the 2230 solid-state drive.......................................................................................................................... 44
Installing the 2230 solid-state drive............................................................................................................................44
Removing the 2280 solid-state drive..........................................................................................................................45
Installing the 2280 solid-state drive............................................................................................................................46
Top bezel............................................................................................................................................................................ 47
Removing the top bezel................................................................................................................................................47
Installing the top bezel................................................................................................................................................. 48
Processor fan and heat-sink assembly...............................................................................................................................50
Removing the processor fan and heat-sink assembly................................................................................................. 50
Installing the processor fan and heat-sink assembly.................................................................................................... 51
Processor liquid-cooling assembly.................................................................................................................................... 52
Removing the processor liquid-cooling assembly.......................................................................................................52
Installing the processor liquid-cooling assembly.........................................................................................................53
Processor.............................................................................................................................................................................55
Removing the processor............................................................................................................................................... 55
Installing the processor.................................................................................................................................................55
Wireless card...................................................................................................................................................................... 56
Removing the wireless card..........................................................................................................................................56
Installing the wireless card............................................................................................................................................57
Antennas.............................................................................................................................................................................59
Removing the antennas................................................................................................................................................ 59
Installing the antennas..................................................................................................................................................60
Front-chassis fan................................................................................................................................................................. 61
Removing the front-chassis fan.....................................................................................................................................61
Installing the front-chassis fan.......................................................................................................................................61
PCIe fan.............................................................................................................................................................................. 62
Removing the PCIe fan.................................................................................................................................................62
Installing the PCIe fan...................................................................................................................................................63
Top-chassis fan................................................................................................................................................................... 64
Removing the top-chassis fan...................................................................................................................................... 64
Installing the top-chassis fan........................................................................................................................................ 65
Front AlienFX LED boards................................................................................................................................................ 66
Removing the Front AlienFX LED board.................................................................................................................... 66
Installing the Front AlienFX LED board.......................................................................................................................67
Power-button board.......................................................................................................................................................... 68
Removing the power-button board.............................................................................................................................68
Installing the power-button board.............................................................................................................................. 69
VR heat sinks.......................................................................................................................................................................70
Removing the VR heat sink...........................................................................................................................................70
Installing the VR heat sink.............................................................................................................................................72
System board...................................................................................................................................................................... 73
Removing the system board..........................................................................................................................................73
4
Installing the system board........................................................................................................................................... 78
Entering the Service Tag in the BIOS setup program.................................................................................................80
Chapter 3: Device drivers.......................................................................................................................81
Operating system................................................................................................................................................................81
Downloading the audio driver........................................................................................................................................... 81
Downloading the graphics driver...................................................................................................................................... 81
Downloading the USB driver.............................................................................................................................................82
Downloading the WiFi driver............................................................................................................................................ 83
Downloading the media-card reader driver.....................................................................................................................83
Downloading the chipset driver........................................................................................................................................84
Downloading the network driver...................................................................................................................................... 84
Chapter 4: System setup........................................................................................................................86
System setup.......................................................................................................................................................................86
Entering BIOS setup program........................................................................................................................................... 86
Navigation keys..................................................................................................................................................................86
Boot Sequence................................................................................................................................................................... 86
System setup options..........................................................................................................................................................87
System and setup password................................................................................................................................................91
Assigning a system setup password..............................................................................................................................92
Deleting or changing an existing system setup password.......................................................................................... 92
Clearing CMOS settings...............................................................................................................................................93
Clearing BIOS (System Setup) and System passwords............................................................................................... 93
Updating the BIOS.............................................................................................................................................................93
Updating the BIOS in Windows...................................................................................................................................93
Updating the BIOS using the USB drive in Windows.................................................................................................93
Updating the BIOS from the F12 One-Time boot menu............................................................................................ 94
Chapter 5: Troubleshooting...................................................................................................................95
SupportAssist diagnostics.................................................................................................................................................. 95
System-diagnostic lights....................................................................................................................................................95
Recovering the operating system......................................................................................................................................96
WiFi power cycle............................................................................................................................................................... 96
Drain residual flea power (perform hard reset)................................................................................................................96
Modern Standby.................................................................................................................................................................97
Chapter 6: Getting help and contacting Alienware............................................................................. 98
5
Working inside your computer
Before working inside your computer
About this task
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from
the network device.
5. Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped with your
computer.
WARNING: Before working inside your computer, read the safety information that is shipped with your computer. For
more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
WARNING: Disconnect your computer from all power sources before opening the computer cover or panels. After you
finish working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical
outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the pins and the
contacts.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance
team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions
that is shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such
as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static
electricity which could harm internal components.
CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables have
connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable. When disconnecting
cables, keep them evenly aligned to avoid bending the connector pins. When connecting cables, ensure that the ports and
the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
6
CAUTION: Exercise caution when handling Lithium-ion batteries in laptops. Swollen batteries should not be used and
should be replaced and disposed properly.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Safety precautions
The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.
Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or
reassembly:
●Turn off the system and all attached peripherals.
●Disconnect the system and all attached peripherals from AC power.
●Disconnect all network cables, telephone, and telecommunications lines from the system.
●Use an ESD field service kit when working inside any desktop to avoid electrostatic discharge (ESD) damage.
●After removing any system component, carefully place the removed component on an anti-static mat.
●Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.
Standby power
Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are
essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and suspended
into a sleep mode and has other advanced power management features.
Unplugging, pressing and holding the power button for 20 seconds should discharge residual power in the system board.
Bonding
Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the
use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare metal
and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and ensure that you
remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors,
memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent
problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD
protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in
previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an
immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a
static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional
memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent
failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock,
but the tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened
trace may take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory
errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.
Perform the following steps to prevent ESD damage:
7
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not
provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with
increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on
the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on
the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and
bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is
temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat,
and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless
wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be
checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist
strap and bonding wire at least once per week.
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a
best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the
best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they
have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the
button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are
insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example,
deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed
in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open
flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of
system that is being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area,
insulators such as Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive
parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags
are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part
arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the
original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected
work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always
place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be
returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat
at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts
while performing service and that they use anti-static bags for transporting sensitive components.
8
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these
parts in anti-static bags for safe transport.
Lifting equipment
Adhere to the following guidelines when lifting heavy weight equipment:
CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device.
1. Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.
2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.
3. Lift with your legs, not your back.
4. Keep the load close. The closer it is to your spine, the less force it exerts on your back.
5. Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid twisting
your body and back.
6. Follow the same techniques in reverse to set the load down.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
9
Removing and installing components
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Inside view of your computer
1. Side light 2. Top-chassis fan
3. 3.5-inch hard drive 4. Front-chassis fan
5. Memory module 6. PCIe fan
7. Graphics-card end holder 8. 2.5-inch hard drive
9. Coin-cell battery 10. Graphics card
11. Power-supply unit 12. Graphics-card bracket holder
13. Power-supply unit bracket 14. Processor cooler
15. Radiator and fan assembly
10
System-board components
1. Ring Ambient Power Button connector 2. FAN_SYS3 connector
3. Wireless-card slot (M.2 WLAN) 4. FAN_SYS2 connector
5. SATA 6 Gbps drive connector (SATA0) 6. SATA 6 Gbps drive connector (SATA1)
7. SATA 6 Gbps drive connector (SATA2) 8. Power-supply connector (ATX1_2)
9. Coin-cell battery 10. PCI-Express x4 slot (SLOT4)
11. PCI-Express x16 mechanical/x16 electrical slot PCIe Gen4
(SLOT2)
12. Solid-state drive slot (M.2 PCIe SSD.0)
13. PCI-Express x4 slot (SLOT1) 14. Rear-chassis fan connector (FAN_SYS1)
11
15. Fan LED connector (FAN LED1) 16. Fan pump connector (FAN PUMP)
17. CPU fan connector 18. Top-chassis fan connector (FAN_SYS4)
19. CPU socket 20.Power-supply connector (ATX2)
21. Power-supply connector (ATX3) 22.Memory-module slot, DIMM 3
23. Memory-module slot, DIMM 1 24.Memory-module slot, DIMM 4
25.Memory-module slot, DIMM 2 26.SATA power connector
27. Side light connector
Recommended tools
The procedures in this document may require the following tools:
●Philips screwdriver #1
●Flat-head screwdriver
●Plastic scribe
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then
place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when
the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when replacing a
component.
NOTE: Screw color may vary with the configuration ordered.
Table 1. Screw list
Component Screw type Quantity Screw image
Power-supply unit bracket #6-32x1/4" 2
Power-supply unit bracket (for
computers shipped with clear
left-side cover)
#6-32x1/4" 2
Power-supply unit #6-32x1/4" 4
Power-supply unit (for
computers shipped with clear
left-side cover)
#6-32x1/4" 4
Side light (for computers shipped
with clear left-side cover)
M3x5 2
Radiator and fan assembly M3x5 1
Antennas M3x3 2
Top bezel M3x7 4
12
Table 1. Screw list (continued)
Component Screw type Quantity Screw image
Top bezel #6-32x1/4" 2
Solid-state drive (M.2 slot) M2x3 1
Wireless card M2x3 1
Front AlienFX LED board M3x8 4
Power-button board M2x3 1
System board #6-32x1/4" 10
Cable cover
Removing the cable cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
About this task
The following image indicates the location of the cable cover and provides a visual representation of the removal procedure.
NOTE: The cable cover is an optional accessory.
13
Steps
Pull the cable cover from the top to lift the cable cover from the chassis.
Installing the cable cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the cable cover and provides a visual representation of the installation procedure.
NOTE: The cable cover is an optional accessory.
14
Steps
1. Align the cable cover with the slots at the rear of the chassis.
2. Slide the cable cover back into its place on the rear of the chassis.
Next steps
1. Follow the procedure in After working inside your computer.
Left-side cover
Removing the left-side cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
About this task
The following images indicate the location of the left-side cover and provide a visual representation of the removal procedure.
NOTE: The clear left-side cover is shipped with some computers.
15
Steps
1. Loosen the captive screw (#6-32) that secures the side-cover release latch to the chassis.
2. Pull the side-cover release latch to release the left-side cover away from the chassis.
3. Lift the left-side panel from the chassis.
Installing the left-side cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the left-side cover and provide a visual representation of the installation procedure.
NOTE: The clear left-side cover is shipped with some computers.
16
Steps
1. Locate the tabs on the left-side cover and slots on the chassis.
2. Rotate the left-side cover towards the chassis until it snaps into place.
3. Tighten the captive screw (#6-32) that secures the side-cover release latch to the chassis.
Next steps
1. Follow the procedure in After working inside your computer.
Top cover
Removing the top cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the top cover and provide a visual representation of the removal procedure.
17
Steps
1. Press your thumbs down at the rear of the top cover, and use your fingers to pull the two rear latches out to loosen the top cover
at its rear.
NOTE: The top cover is secured tight to the chassis by four latches.
2. Press your thumbs down at the front of the top cover, and use your fingers to pull the two front latches out to loosen the top
cover at its front.
3. Press your thumbs down at the middle of the top cover to release the remaining two latches and lift the top cover.
18
Installing the top cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the top cover and provides a visual representation of the installation procedure.
Steps
Align the tabs on the top cover with the slots on the chassis and snap the top cover into place.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
Right-side cover
Removing the right-side cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
About this task
The following images indicate the location of the right-side cover and provide a visual representation of the removal procedure.
19
Steps
1. Knock the top rear tab of the right-side cover until the top of right-side cover is detached from the chassis.
2. Knock the bottom rear tab of the right-side cover until the bottom of the right-side cover is detached from the chassis.
3. Remove the right-side cover from the chassis.
Installing the right-side cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
20
About this task
Steps
1. Align the tabs on the right-side cover with the slots on the chassis.
2. Push the right-side cover towards the chassis until it snaps into place.
Next steps
1. Install the top cover.
2. Install the left-side cover.
3. Follow the procedure in After working inside your computer.
Front bezel
Removing the front bezel
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
About this task
The following images indicate the location of the front bezel and provide a visual representation of the removal procedure.
21
Steps
1. Place the computer in an upright position.
2. Disconnect the front I/O-panel cable from the system board.
3. Pull the tabs of the front bezel from the slots on the front panel.
NOTE: Start with tab on top, proceed to the tabs on the left of the front bezel, and then to the tabs on the right of the front
bezel.
4. Pull the front bezel, together with the front I/O-panel cable, away from the chassis slowly.
Installing the front bezel
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
22
About this task
The following images indicate the location of the front bezel and provide a visual representation of the installation procedure.
Steps
1. Align the front bezel with the front panel.
2. Route the front I/O-panel cable through the slot on the front panel.
3. Push the front bezel towards the front panel and ensure the tabs clip onto the slots of the front panel.
NOTE: Start with tab on top, proceed to the tabs on the left of the front bezel, and then to the tabs on the right of the front
bezel.
4. Connect the front I/O-panel cable to the system board.
Next steps
1. Install the right-side cover.
23
2. Install the top cover.
3. Install the left-side cover.
4. Follow the procedure in After working inside your computer.
Side light
Removing the Side light
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
5. Remove the front bezel.
About this task
NOTE: Side light is available only on computers that are shipped with clear left-side covers.
The following images indicate the location of the Side light and provide a visual representation of the removal procedure.
Steps
1. Lay the computer on its right side.
2. Disconnect the Side-light cable from the system board.
3. Remove the two screws (M3x5) that secure the Side light to the chassis.
4. Lift the left side of the Side light bar slightly from the screw hole at the rear of the chassis.
5. Lift the right side of the Side light bar slowly from the screw hole at the front of the chassis.
6. Lift the entire Side light bar from the chassis.
24
Installing the Side light
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
NOTE: Side light is available only on computers that are shipped with clear left-side covers.
The following images indicate the location of the Side light and provide a visual representation of the installation procedure.
Steps
1. Lay the computer on its right side.
2. Align the left screw hole of the Side light with the screw on the rear of the chassis.
3. Lift the right side of the Side light slowly until the right screw of the Side light is aligned with the screw hole on the front of the
chassis.
4. Replace the two screws (M3x5) that secure the Side light to the chassis.
5. Connect the side-light cable to the system board.
Next steps
1. Install the front bezel.
2. Install the right-side cover.
3. Install the top cover.
4. Install the left-side cover.
5. Follow the procedure in After working inside your computer.
25
2.5-inch hard drive
Removing the 2.5-inch hard drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the 2.5-inch hard drive and provide a visual representation of the removal procedure.
Steps
1. Disconnect the hard-drive data and hard-drive power cables from the hard drive.
2. Press the release tabs on the hard-drive carrier and slide the hard-drive assembly out of the hard-drive cage.
3. Pry the hard-drive carrier to release the tabs on the assembly from the slots on the hard drive.
4. Lift the hard drive out of the hard-drive assembly.
NOTE: Note the orientation of the hard drive so that you can replace it correctly.
26
NOTE: Repeat the steps to remove any additional 2.5-inch hard drive from your computer.
Installing the 2.5-inch hard drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the 2.5-inch hard drive and provide a visual representation of the installation
procedure.
27
NOTE: Note the orientation on the hard-drive carrier to replace it correctly.
Steps
1. Align the hard drive with the pins on the hard-drive carrier.
2. Using the tabs on the opposite side, flex open the carrier to insert the pins on the other side.
3. Slide the hard-drive assembly into the hard-drive cage until it snaps into place.
4. Connect the hard-drive data cable and hard-drive power cable to the hard drive.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
3. Verify if the storage device is installed correctly (optional):
a. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying
storage device in device manager.
b. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying your
storage device in system setup (BIOS).
NOTE: To install the operating system on to your storage device, see Reinstall Windows to the Dell factory image using
recovery media in the knowledge base article 000176966.
28
Identifying the storage device in Device Manager
Steps
1. On the taskbar, click the search box, and then type Device Manager.
2. Click Device Manager.
The Device Manager window is displayed.
3. Expand Disk drives.
Identifying the storage device in system setup (BIOS)
Steps
1. Turn on or restart your computer.
2. Press F2 when the Dell logo is displayed on the screen to enter the BIOS setup program.
A list of hard drives are displayed under the System Information in the General group.
3.5-inch hard drive
Removing the 3.5-inch hard drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the 3.5-inch hard drive and provide a visual representation of the removal procedure.
29
Steps
1. Lift the side light bar to reach the hard-drive data and hard-drive power cables of the hard drive.
2. Slide your finger under the hard-drive power cable as close as possible to the power cable plug, and pull the hard-drive power
cable to disconnect the cable.
3. Slide your finger under the hard-drive data cable as close as possible to the data cable plug, and pull the hard-drive data cable to
disconnect the cable.
4. Push the side light bar down.
5. Press the release tabs on the hard-drive carrier and slide the hard-drive carrier out of the hard-drive cage.
6. Pry the hard-drive carrier to release the tabs on the carrier from the slots on the hard drive.
7. Lift the hard drive out of the hard-drive carrier.
NOTE: Note the orientation of the hard drive so that you can replace it correctly.
30
Installing the 3.5-inch hard drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the 3.5-inch hard drive and provide a visual representation of the installation
procedure.
31
NOTE: Note the orientation on the hard-drive carrier to replace it correctly.
Steps
1. Align the hard drive with the pins on the hard-drive carrier.
2. Using the tabs on the opposite side, flex open the carrier to insert the pins on the other side.
3. Slide the hard-drive assembly into the hard-drive cage until it snaps into place.
4. Lift the side light bar.
5. Connect the hard-drive data cable and hard-drive power cable to the hard drive.
6. Push the side light bar down.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
32
3. Verify if the storage device is installed correctly (optional):
a. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying
storage device in device manager.
b. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying your
storage device in system setup (BIOS).
NOTE: To install the operating system on to your storage device, see Reinstall Windows to the Dell factory image using
recovery media in the knowledge base article 000176966.
Power-supply unit
Removing the power-supply unit
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
NOTE: Note the routing of all cables as you remove them so that you can route them correctly after you replace the power-
supply unit.
About this task
The following images indicate the location of the power-supply unit and provide a visual representation of the removal procedure.
33
Steps
1. Disconnect the power-supply unit cables from the power-supply unit extension cables on the right side of the computer.
2. Slide the power-supply unit cables out from the routing guide.
3. Lay the computer on the right side.
4. Release the power-supply unit cables from the plastic cable clip.
34
5. Disconnect the power-supply cables from the system board.
6. Press the release clips on the power-supply connectors before disconnecting the power-supply cables from the system board.
7. Disconnect the graphics-card power cables from the power-supply unit.
8. Press the release clips on the graphics-card power connectors before disconnecting the graphics-card power cables from the
power-supply unit.
9. Slide the release latch to the unlock position and lift the graphics-card bracket away from the graphics card.
10.Remove the two screws (#6-32x1/4") that secure the power-supply unit bracket to the power-supply unit.
11. Slide and lift the power-supply unit bracket from the power-supply unit.
12. Remove the four screws (#6-32x1/4") that secure the power-supply unit to the chassis.
13. Slide and lift the power-supply unit, along with the cables, off the chassis.
Installing the power-supply unit
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
WARNING: The cables and ports on the back of the power-supply unit are color-coded to indicate the different power
wattage. Ensure that you plug in the cable to the correct port. Failure to do so may result in damaging the power-supply
unit and/or system components.
About this task
The following images indicate the location of the power-supply unit and provide a visual representation of the installation procedure.
35
Steps
1. Lay the computer on the right side.
2. Place the power-supply unit on the chassis.
3. Align the screw holes on the power-supply unit with the screw holes on the chassis.
4. Replace the four screws (#6-32x1/4") that secure the power-supply unit to the chassis.
5. Place the power-supply unit bracket on the power-supply unit.
36
6. Replace the two screws (#6-32x1/4") that secure the power-supply unit bracket to the power-supply unit.
7. Replace the graphics-card bracket and slide the release latch to the lock position.
8. Place the power-supply unit cables back into the plastic cable clip.
9. Connect the power-supply cables to the system board.
10.Connect the graphics-card power cables to the power-supply unit.
11. Place the computer in an upright position.
12. Place the power-supply unit cables back to the routing guide on the right side of the computer.
13. Connect the power-supply unit cables to the power-supply unit extension cables on the right side of the computer.
Next steps
1. Install the right-side cover.
2. Install the top cover.
3. Install the left-side cover.
4. Follow the procedure in After working inside your computer.
Coin-cell battery
Removing the coin-cell battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
WARNING: Before working inside your computer, read the safety information that is shipped with your computer. For
more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that
you note the BIOS setup program’s settings before removing the coin-cell battery.
2. Remove the left-side cover.
About this task
The following images indicate the location of the coin-cell battery and provide a visual representation of the removal procedure.
37
Steps
1. Lay the computer on the right side.
2. Press the battery-release lever away from the coin-cell battery until the coin-cell battery pops up.
3. Lift the coin-cell battery out of its socket.
Installing the coin-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the coin-cell battery and provide a visual representation of the installation procedure.
Steps
Insert the new coin-cell battery (CR2032) into the battery socket with the positive side facing up, and snap the battery into place.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
Memory modules
Removing the memory modules
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
38
About this task
The following images indicate the location of the memory modules and provide a visual representation of the removal procedure.
Steps
1. Lay the computer on the right side.
2. Push the securing clips away from the memory module.
3. Lift the memory module off the memory-module slot.
NOTE: Repeat step 2 to step 3 to remove any other memory modules installed in your computer.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges. Do not touch the
components on the memory module.
Installing the memory modules
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the memory modules and provide a visual representation of the installation procedure.
39
Steps
1. Ensure that the securing clips are extended away from the memory-module slot.
2. Align the notch on the memory module with the tab on the memory-module slot.
3. Insert the memory module into the memory-module slot and press the memory module down until it snaps into position and the
securing clips lock in place.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges. Do not touch the
components on the memory module.
NOTE: Repeat step 1 to step 3 to replace any other memory modules installed in your computer.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
Single-graphics card
Removing the single-graphics card
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the single-graphics card and provide a visual representation of the removal procedure.
40
41
Steps
1. Lay the computer on the right side.
2. Lift the pull tab and open the expansion-card door.
3. Press the releasing clip on the graphics-card power connectors and disconnect the graphics-card power cables from the graphics
card.
4. Slide the release latch to its unlock position and lift the graphics-card end holder away from the PCIe fan.
5. Slide the release latch to its unlock position and lift the graphics-card bracket away from the graphics card.
6. Push the securing tab on the PCIe x16 slot down, grasp the graphics card by its top edge, and ease it out of the slot.
Installing the single-graphics card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the single-graphics card and provide a visual representation of the installation
procedure.
42
Steps
1. Place the card into the PCIe x16 slot and press down firmly until the single-graphics card snaps into place.
2. Connect the graphics-card power cables to the graphics card.
3. Replace the graphics-card bracket onto the graphics-card bracket holder and slide the latch into its lock position.
4. Replace the graphics-card end holder over the PCIe fan and slide the latch into its lock position.
5. Close the expansion-card door and snap the latch back into position.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
43
Solid-state drive
Removing the 2230 solid-state drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the 2230 solid-state drive and provide a visual representation of the removal
procedure.
Steps
1. Remove the screw (M2x3) that secures the 2230 solid-state drive to the system board.
2. Slide and lift the 2230 solid-state drive off the system board.
Installing the 2230 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
About this task
NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in the SSD slot.
NOTE: Depending on the configuration ordered, your computer may support either 2230 solid-state drive or 2280 solid-state
drive in the SSD slot.
If you want to replace your 2230 solid-state drive with a 2280 solid-state drive, see Installing the 2280 solid-state drive.
44
The following images indicate the location of the 2230 solid-state drive and provide a visual representation of the installation
procedure.
Steps
1. Align the notch on the 2230 solid-state drive with the tab on the solid-state drive slot.
2. Insert the 2230 solid-state drive at a 45-degree angle into the system board.
3. Press the other end of the 2230 solid-state drive down and replace the screw (M2x3) that secures the 2230 solid-state drive to
the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
3. Verify if the storage device is installed correctly (optional):
a. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying
storage device in device manager.
b. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying your
storage device in system setup (BIOS).
NOTE: To install the operating system on to your storage device, see Reinstall Windows to the Dell factory image using
recovery media in the knowledge base article 000176966.
Removing the 2280 solid-state drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the 2280 solid-state drive and provide a visual representation of the removal
procedure.
45
Steps
1. Remove the screw (M2x3) that secures the 2280 solid-state drive to the system board.
2. Slide and lift the 2280 solid-state drive off the system board.
Installing the 2280 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
About this task
NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in the SSD slot.
NOTE: Depending on the configuration ordered, your computer may support either 2280 solid-state drive or 2230 solid-state
drive in the SSD slot.
If you want to replace your 2280 solid-state drive with a 2230 solid-state drive, see Installing the 2230 solid-state drive.
The following images indicate the location of the 2280 solid-state drive and provide a visual representation of the installation
procedure.
46
Steps
1. Align the notch on the 2280 solid-state drive with the tab on the solid-state drive slot.
2. Insert the 2280 solid-state drive at a 45-degree angle into the system board.
3. Press the other end of the 2280 solid-state drive down and replace the screw (M2x3) that secures the 2280 solid-state drive to
the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
3. Verify if the storage device is installed correctly (optional):
a. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying
storage device in device manager.
b. If you are replacing a storage device which does not have the operating system installed, follow the steps in Identifying your
storage device in system setup (BIOS).
NOTE: To install the operating system on to your storage device, see Reinstall Windows to the Dell factory image using
recovery media in the knowledge base article 000176966.
Top bezel
Removing the top bezel
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
About this task
The following images indicate the location of the top bezel and provide a visual representation of the removal procedure.
47
Steps
1. Place the computer in an upright position.
2. Remove the two screws (#6-32x1/4") that secure the top bezel to the chassis.
3. Remove the four screws (M3x7) that secure the top bezel to the chassis.
4. Lift the top bezel off the chassis.
Installing the top bezel
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the top bezel and provide a visual representation of the installation procedure.
48
Steps
1. Place the computer in an upright position.
2. Align the top bezel screw holes with screw holes on the chassis.
3. Place the top bezel on the chassis.
4. Replace the four screws (M3x7) that secure the top bezel to the chassis.
5. Replace the two screws (#6-32x1/4") that secure the top bezel to the chassis.
Next steps
1. Install the right-side cover.
2. Install the top cover.
3. Install the left-side cover.
4. Follow the procedure in After working inside your computer.
49
Processor fan and heat-sink assembly
Removing the processor fan and heat-sink assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
NOTE: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you
touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your
skin can reduce the heat transfer capability of the thermal grease.
2. Remove the left-side cover.
About this task
The following images indicate the location of the processor fan and heat-sink assembly and provide a visual representation of the
removal procedure.
Steps
1. Lay the computer on the right side.
2. Disconnect the processor-fan cable from the system board.
3. In reverse sequential order, loosen the four captive screws that secure the processor fan and heat-sink assembly to the system
board.
4. Lift the processor fan and heat-sink assembly off the system board.
50
Installing the processor fan and heat-sink assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: If either the processor or the heat sink is replaced, use the thermal grease that is provided in the kit to ensure
that thermal conductivity is achieved.
About this task
The following images indicate the location of the processor fan and heat-sink assembly and provide a visual representation of the
installation procedure.
Steps
1. Place the processor fan and heat-sink assembly on the processor.
2. Align the captive screws on the processor fan heat-sink assembly with the screw holes on the system board.
3. In sequential order, tighten the four captive screws that secure the processor fan and heat-sink assembly to the system board.
4. Connect the processor-fan cable to the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
51
Processor liquid-cooling assembly
Removing the processor liquid-cooling assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
WARNING: Despite having a plastic shield, the processor liquid-cooling assembly may be very hot during normal
operation. Ensure that it had sufficient time to cool before you touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your
skin can reduce the heat transfer capability of the thermal grease.
2. Remove the left-side cover.
About this task
The following images indicate the location of the processor liquid-cooling assembly and provide a visual representation of the
removal procedure.
52
Steps
1. Lay the computer on the right side.
2. Disconnect the processor-cooling assembly cables from the system board.
3. In reverse sequential order, loosen the four captive screws that secure the processor cooler to the system board.
4. Remove the screw (M3x5) that secures the radiator and fan assembly to the chassis.
5. Lift the processor-cooling assembly along with the cables off the system board.
Installing the processor liquid-cooling assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
53
CAUTION: Incorrect alignment of the processor liquid-cooling assembly can damage the system board and processor.
CAUTION: If either the processor or the heat sink is replaced, use the thermal grease that is provided in the kit to ensure
that thermal conductivity is achieved.
About this task
The following images indicate the location of the processor liquid-cooling assembly and provide a visual representation of the
installation procedure.
Steps
1. Align the screw hole of the radiator and fan assembly to the screw hole on the chassis.
NOTE: Ensure that the hoses are facing the front of the computer.
2. Replace the screw (M3x5) that secures the radiator and fan assembly to the chassis.
54
3. Align the screw holes on the processor cooler with the screw holes on the system board.
4. In sequential order, tighten the four captive screws that secure the processor cooler to the system board.
5. Connect the processor-cooling assembly cables to the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
Processor
Removing the processor
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the processor liquid-cooling assembly or processor fan and heat-sink assembly, as applicable.
About this task
The following images indicate the location of the processor and provide a visual representation of the removal procedure.
Steps
1. Press the release lever down and then push it away from the processor to release it from the tab.
2. Extend the release lever completely.
3. Lift the processor off the processor socket.
Installing the processor
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
55
About this task
The following images indicate the location of the processor and provide a visual representation of the installation procedure.
Steps
1. Ensure that the release lever on the processor socket is fully extended.
CAUTION: Position the processor correctly in the processor socket to avoid permanent damage to the processor.
2. Align the pin-1 corner on the processor with the pin-1 corner on the processor socket, and then place the processor in the
processor socket.
CAUTION: Ensure that the processor-cover notch is positioned underneath the alignment post.
3. Push the release lever down and place it under the tab next to the processor socket.
Next steps
1. Install the processor liquid-cooling assembly or processor fan and heat-sink assembly, as applicable.
2. Install the left-side cover.
3. Follow the procedure in After working inside your computer.
Wireless card
Removing the wireless card
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the wireless card and provide a visual representation of the removal procedure.
56
Steps
1. Remove the screw (M2x3) that secures the wireless card to the system board.
2. Lift the wireless-card bracket off the wireless card.
3. Disconnect the antenna cables from the wireless card.
4. Slide and remove the wireless card from the wireless-card slot.
Installing the wireless card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: To avoid damage to the wireless mini-card, do not place any cables under it.
About this task
The following images indicate the location of the wireless card and provide a visual representation of the installation procedure.
57
Steps
1. Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the wireless card supported by your computer.
Table 2. Antenna-cable color scheme
Connectors on the wireless card Antenna-cable color
Main (white triangle) White
Auxiliary (black triangle) Black
2. Place the wireless-card bracket on the wireless card.
3. Align the notch on the wireless card with the tab on the wireless-card slot.
4. Slide the wireless card at an angle into the wireless-card slot.
5. Replace the screw (M2x3) that secures the wireless card to the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
58
Antennas
Removing the antennas
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the wireless card.
4. Remove the top cover.
5. Remove the right-side cover.
6. Remove the front bezel.
About this task
The following images indicate the location of the antennas and provide a visual representation of the removal procedure.
Steps
1. Remove the two screws (M3x3) that secure the antennas to the chassis.
2. Peel the two antennas and remove them from the slots of the chassis.
3. Remove the antenna cables from the routing guides on the chassis.
4. Remove the antenna cables from the routing clip inside the chassis.
5. Pull the antenna cables carefully through the hole on the chassis, and remove the antennas with their cables from the chassis.
59
Installing the antennas
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the antennas and provide a visual representation of the installation procedure.
Steps
1. Place the antennas on the slots of the chassis and adhere the antennas to the chassis.
2. Align the screw holes and replace the two screws (M3x3) that secures the antennas to the chassis.
3. Route the antenna cables through the routing guides on the chassis.
4. Push the end of the antenna cables with the connectors to the wireless-card through the hole of the chassis.
5. Route the antenna cables through the routing clip inside the chassis.
Next steps
1. Install the front bezel.
2. Install the right-side cover.
3. Install the top cover.
4. Install the wireless card.
5. Install the left-side cover.
6. Follow the procedure in After working inside your computer.
60
Front-chassis fan
Removing the front-chassis fan
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the front-chassis fan and provide a visual representation of the removal procedure.
Steps
1. Lay the computer on its right side.
2. Disconnect the front-chassis fan cable from the system board.
3. Press the releasing clip; slide and lift the front-chassis off the chassis.
Installing the front-chassis fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
61
About this task
The following images indicate the location of the front-chassis fan and provide a visual representation of the installation procedure.
Steps
1. Lay the computer on its right side.
2. Align the front-chassis fan with the slot on the chassis; slide and push the fan until the releasing clip snaps into position.
3. Connect the front-chassis fan cable to the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
PCIe fan
Removing the PCIe fan
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the PCIe fan and provide a visual representation of the removal procedure.
62
Steps
1. Lay the computer on its right side.
2. Slide the release latch to the unlock position and lift the graphics-card end holder away from the chassis.
3. Disconnect the PCIe fan cable from the system board.
4. Push the tab to release the PCIe fan from the chassis.
5. Slide and lift the PCIe fan off the chassis.
Installing the PCIe fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the PCIe fan and provide a visual representation of the installation procedure.
63
Steps
1. Lay the computer on its right side.
2. Align the tabs on the PCIe fan with the slots on the chassis.
3. Slide and push the fan until the releasing clip snaps into position on the chassis.
4. Connect the PCIe fan cable to the system board.
5. Replace the graphics-card end holder and slide the release latch to the lock position.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
Top-chassis fan
Removing the top-chassis fan
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
About this task
The following images indicate the location of the top-chassis fan and provide a visual representation of the removal procedure.
64
Steps
1. Lay the computer on the right side.
2. Disconnect the top-chassis fan cable from the system board.
3. Press the releasing clip of the top-chassis fans.
4. Slide and lift the top-chassis fan from the chassis.
Installing the top-chassis fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the top-chassis fan and provide a visual representation of the installation procedure.
65
Steps
1. Lay the computer on its right side.
2. Align the top-chassis fan with the slot on the chassis.
3. Push the top-chassis fan into the slot on the chassis until its releasing clip is locked into place.
4. Connect the top-chassis fan cable to the system board.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
Front AlienFX LED boards
Removing the Front AlienFX LED board
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
5. Remove the front bezel.
66
About this task
The following images indicate the location of the front AlienFX LED board and provide a visual representation of the removal
procedure.
Steps
1. Place the front bezel on a flat surface to locate the AlienFX LED board.
2. Remove the four screws (M3x8) that secure the AlienFX LED board to the front bezel.
3. Lift the AlienFX LED board slightly off the front bezel and disconnect the power-button board cable from the power-button
board.
4. Lift the AlienFX LED board with its cables off the front bezel.
Installing the Front AlienFX LED board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the front AlienFX LED board and provide a visual representation of the installation
procedure.
67
Steps
1. Place the front bezel on a flat surface and locate the power-button board.
2. Bring the AlienFX LED board near the front bezel and connect the power-button board cable to the power-button board.
3. Align the screw hole of the AlienFX LED board to the screw hole on the front bezel.
4. Replace the four screws (M3x8) that secure the AlienFX LED board to the front bezel.
Next steps
1. Install the front bezel.
2. Install the right-side cover.
3. Install the top cover.
4. Install the left-side cover.
5. Follow the procedure in After working inside your computer.
Power-button board
Removing the power-button board
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
5. Remove the front bezel.
6. Remove the front AlienFX LED board.
About this task
The following images indicate the location of the power-button board and provide a visual representation of the removal procedure.
68
Steps
1. Remove the screw (M2x3) that secures the power-button board to the front bezel.
2. Lift the power-button board off the front bezel.
Installing the power-button board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the power-button board and provide a visual representation of the installation
procedure.
69
Steps
1. Align the screw hole on the power-button board with the screw hole on the front bezel.
2. Replace the screw (M2x3) that secures the power-button board to the front bezel.
Next steps
1. Install the front AlienFX LED board.
2. Install the front bezel.
3. Install the right-side cover.
4. Install the top cover.
5. Install the left-side cover.
6. Follow the procedure in After working inside your computer.
VR heat sinks
Removing the VR heat sink
Prerequisites
1. Follow the procedure in Before working inside your computer.
NOTE: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you
touch it.
CAUTION: If either the processor or the heat sink is replaced, use the thermal grease that is provided in the kit to
ensure that thermal conductivity is achieved.
NOTE: Do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of
the thermal grease.
NOTE: The VR heat sinks are shipped as separate units and they do not ship along with the new system board. Remove the
VR heat sinks from old system board for transfer to the new system board.
2. Remove the left-side cover.
70
About this task
The following images indicate the location of the VR heat sink and provide a visual representation of the removal procedure.
Steps
1. Lay the computer on the right side.
2. Loosen the captive screws that secure the VR heat sink to the system board.
3. Repeat the same process for the other VR heat sink.
4. Lift the VR heat sinks off the system board.
71
Installing the VR heat sink
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
CAUTION: If either the processor or the heat sink is replaced, use the thermal grease that is provided in the kit to ensure
that thermal conductivity is achieved.
NOTE: Do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of the
thermal grease.
NOTE: The VR heat sinks are shipped as separate units and they do not ship along with the new system board. Remove the VR
heat sinks from old system board for transfer to the new system board.
About this task
The following images indicate the location of the VR heat sink and provide a visual representation of the installation procedure.
Steps
1. Align the captive screws of the VR heat sink with the screw holes on the system board.
2. Tighten the two captive screws that secure the VR heat sink to the system board.
3. Repeat the same procedure with the other VR heat sink.
Next steps
1. Install the left-side cover.
2. Follow the procedure in After working inside your computer.
72
System board
Removing the system board
Prerequisites
1. Follow the procedure in Before working inside your computer.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program
after you replace the system board.
NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program.
You must make the appropriate changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2. Remove the left-side cover.
3. Remove the top cover.
4. Remove the right-side cover.
5. Remove the front bezel.
6. Remove the memory module.
7. Remove the single-graphics card.
8. Remove the 2230 solid-state drive or the 2280 solid-state drive.
9. Remove the wireless card.
10.Remove the processor liquid-cooling assembly or processor fan and heat-sink assembly, as applicable.
11. Remove the processor.
12. Remove the VR heat sink.
About this task
The following image indicates the connectors on your system board.
73
1. Ring Ambient Power Button connector
2. FAN_SYS3 connector
3. Wireless-card slot (M.2 WLAN)
4. FAN_SYS2 connector
5. SATA 6 Gbps drive connector (SATA0)
6. SATA 6 Gbps drive connector (SATA1)
7. SATA 6 Gbps drive connector (SATA2)
8. Power-supply connector (ATX1_2)
9. Coin-cell battery
10.PCI-Express x4 slot (SLOT4)
11. PCI-Express x16 mechanical/x16 electrical slot PCIe Gen4 (SLOT2)
74
12. Solid-state drive slot (M.2 PCIe SSD.0)
13. PCI-Express x4 slot (SLOT1)
14. Rear-chassis fan connector (FAN_SYS1)
15.Fan LED connector (FAN LED1)
16.Fan pump connector (FAN PUMP)
17. CPU fan connector
18.Top-chassis fan connector (FAN_SYS4)
19.CPU socket
20.Power-supply connector (ATX2)
21. Power-supply connector (ATX3)
22.Memory-module slot, DIMM 3
23.Memory-module slot, DIMM 1
24.Memory-module slot, DIMM 4
25.Memory-module slot, DIMM 2
26.SATA power connector
27.Side light connector
The following images indicate the location of the system board and provide a visual representation of the removal procedure.
75
76
Steps
1. Disconnect the hard-drive data cables from the system board.
2. Disconnect the processor-power cables from the system board.
3. Disconnect the system-board power cables from the system board.
4. Disconnect the top-chassis fan power cable from the system board.
5. Disconnect the front-chassis fan power cable from the system board.
6. Disconnect the side-light power cable from the system board.
7. Disconnect the SATA power cable from the system board.
8. Disconnect all the cables that are connected to the system board.
NOTE: Note the routing of all cables as you remove them so that you can route them correctly after you replace the system
board. For information about system-board connectors, see "system-board components".
NOTE: Note the routing of all cables as you remove them so that you can route them correctly after you replace the system
board.
9. Remove the nine screws (#6-32x1/4") that secure the system board to standoffs on the chassis.
10.Remove the screw (#6-32x1/4") that secures the front I/O-bracket to the chassis and remove the front I/O-bracket.
11. Hold the edge of the system board where the front I/O-ports are located.
12. Hold the edge of the system board where the rear ports are located.
13. Lift the system board off the chassis at an angle and remove the system board from the chassis.
77
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the system board and provide a visual representation of the installation procedure.
78
Steps
1. Slide the front I/O-ports on the system board into the front I/O-slot on the chassis and align the screw holes on the system board
with the standoffs on the chassis.
2. Place the system board on the standoffs on the chassis.
3. Align the front I/O-bracket to the front I/O-ports and install the bracket on the chassis.
4. Replace the screw (#6-32x1/4") that secures the front I/O-bracket to the chassis.
5. Replace the nine screws (#6-32x1/4") that secure the system board assembly to the standoffs on the chassis.
6. Route and connect all the cables that were disconnected from the system board.
7. Connect the SATA power cable from the system board.
8. Connect the Side-light power cable from the system board.
9. Connect the front-chassis fan power cable from the system board.
10.Connect the top-chassis fan power cable from the system board.
11. Connect the system-board power cables from the system board.
12. Connect the processor-power cables from the system board.
13. Connect the hard-drive data cables from the system board.
Next steps
1. Install the VR heat sink.
2. Install the processor.
3. Install the processor liquid-cooling assembly or processor fan and heat-sink assembly, as applicable.
4. Install the wireless card.
79
5. Install the 2230 solid-state drive or the 2280 solid-state drive.
6. Install the memory module.
7. Install the front bezel.
8. Install the right-side cover.
9. Install the top cover.
10.Install the left-side cover.
11. Follow the procedure in After working inside your computer.
Entering the Service Tag in the BIOS setup program
Steps
1. Turn on or restart your computer.
2. Press F2 when the Dell logo is displayed to enter the BIOS setup program.
3. Navigate to the Main tab and enter the Service Tag in the Service Tag Input field.
Next steps
NOTE: Service tag is the alphanumeric identifier located at the back side of your computer.
80
Device drivers
Operating system
Your Alienware Aurora Ryzen Edition R14 supports the following operating systems:
●Windows 11 Pro Standard, 64-bit
●Windows 11 Pro Plus, 64-bit
●Windows 11 Home Standard, 64-bit
●Windows 11 Home Plus, 64-bit
●Windows 11 Home Advanced, 64-bit
Downloading the audio driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the system.
12. The application installs all drivers and updates identified.
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Audio in the drop-down list.
15.Click Download to download the audio driver for your computer.
16.After the download is complete, navigate to the folder where you saved the audio driver file.
17. Double-click the audio driver file icon and follow the instructions on the screen to install the driver.
Downloading the graphics driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
81
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the system.
12. The application installs all drivers and updates identified.
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Video in the drop-down list.
15.Click Download to download the graphics driver for your computer.
16.After the download is complete, navigate to the folder where you saved the graphics driver file.
17. Double-click the graphics driver file icon and follow the instructions on the screen to install the driver.
Downloading the USB driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the computer.
12. The application installs all drivers and updates identified.
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Chipset in the drop-down list.
15.Click Download to download the USB driver for your computer.
16.After the download is complete, browse the folder where you saved the USB driver file.
17. Double-click the USB driver file icon and follow the instructions on the screen to install the driver.
82
Downloading the WiFi driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the system.
12. The application installs all drivers and updates identified.
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Network in the drop-down list.
15.Click Download to download the WiFi driver for your computer.
16.After the download is complete, navigate to the folder where you saved the WiFi driver file.
17. Double-click the WiFi driver icon and follow the instructions on the screen to install the driver.
Downloading the media-card reader driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the system.
12. The application installs all drivers and updates identified.
83
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Chipset in the drop-down list.
15.Click Download to download the media-card reader driver for your computer.
16.After the download is complete, navigate to the folder where you saved the media-card reader driver file.
17. Double-click the media-card reader driver file icon and follow the instructions on the screen to install the driver.
Downloading the chipset driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the computer.
12. The application installs all drivers and updates identified.
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Chipset in the drop-down list.
15.Click Download to download the chipset driver for your computer.
16.After the download is complete, browse the folder where you saved the chipset driver file.
17. Double-click the chipset driver file icon and follow the instructions on the screen to install the driver.
Downloading the network driver
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads.
5. Click the Detect Drivers button.
6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.
7. If necessary, your computer starts to download and install SupportAssist.
84
NOTE: Review on-screen instructions for browser-specific instructions.
8. Click View Drivers for My System.
9. Click Download and Install to download and install all driver updates detected for your computer.
10.Select a location to save the files.
11. If prompted, approve requests from User Account Control to make changes on the system.
12. The application installs all drivers and updates identified.
NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is
necessary.
13. For manual download and installation, click Category.
14. Click Network in the drop-down list.
15.Click Download to download the network driver for your computer.
16.After the download is complete, navigate to the folder where you saved the network driver file.
17. Double-click the network driver file icon and follow the instructions on the screen to install the driver.
85
System setup
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.
System setup
CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain
changes can make your computer work incorrectly.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen
information for future reference.
Use the BIOS Setup program for the following purposes:
●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.
●Change the system configuration information.
●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling base
devices.
Entering BIOS setup program
About this task
Turn on (or restart) your computer and press F2 immediately.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart the
system.
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Selects a value in the selected field (if applicable) or follow the link in the field.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message
that prompts you to save any unsaved changes and restarts the system.
Boot Sequence
Boot Sequence allows you to bypass the System Setup–defined boot device order and boot directly to a specific device (for
example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
●Access System Setup by pressing F2 key
●Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are:
●Removable Drive (if available)
●STXXXX Drive (if available)
NOTE: XXX denotes the SATA drive number.
86
●Optical Drive (if available)
●SATA Hard Drive (if available)
●Diagnostics
The boot sequence screen also displays the option to access the System Setup screen.
System setup options
NOTE: Depending on your computer and its installed devices, the items listed in this section may or may not appear.
Table 3. System setup options—Main menu
Main
System Time Displays the current time in hh:mm:ss format.
System Date Displays the current date in mm/dd/yy format.
BIOS Version Displays the BIOS version number.
Product Name Displays the product name. Default: Alienware Aurora
Ryzen Edition R14
Service Tag Displays the service tag of your computer.
Asset Tag Displays the asset tag of your computer.
CPU Type Displays the processor type.
CPU Speed Displays the speed of the processor.
CPU ID Displays the processor identification code.
CPU Cache
L1 Cache Displays the processor L1 cache size.
L2 Cache Displays the processor L2 cache size.
L3 Cache Displays the processor L3 cache size.
First HDD Allows you to configure the first HDD.
M.2 PCIe SSD-0 Enables or disables the M.2 PCIe SSD-0.
System Memory Displays the total computer memory installed.
Memory Speed Displays the memory speed.
Table 4. System setup options—Advanced menu
Advanced
Model Name Selection
Model Name Selection Allows you to select Model Name.
Default: Model Name
Virtualization
Virtualization Enables the computer to run a virtual machine monitor (VMM).
Default: Enabled
Integrated NIC
Integrated NIC Allows you to enable or disable the integrated NIC.
Default: Enabled
SATA/NVME Operation
87
Table 4. System setup options—Advanced menu (continued)
Advanced
SATA/NVME Operation Sets the operating mode of the integrated storage device
controller.
Default: AHCI/NVME
PCIe Resizable Base Address Register
PCIe Resizable Base Address Register Allows you to enable or disable the Resizable Base Address
Register (BAR) feature.
Default: Disabled
IPv4 HTTP Support
IPv4 HTTP Support Allows you to enable or disable IPv4 HTTP Support.
Default: Disabled
IPv6 HTTP Support
IPv6 HTTP Support Allows you to enable or disable IPv6 HTTP Support.
Default: Disabled
USB Configuration
Front USB Ports Allows you to enable or disable the Front USB Ports.
Default: Enabled
Rear USB Ports Allows you to enable or disable the Rear USB Ports.
Default: Enabled
Power Options
Wake Up by Integrated LAN Allow the computer to be powered on by special LAN signals.
Default: Enabled
AC Recovery Sets what action the computer takes when power is restored.
Default: Power Off
Deep Sleep Control Allows you to define the controls when Deep Sleep is enabled.
Default: Enabled in S4 and S5
USB PowerShare Allows you to charge external devices.
Default: Disabled
USB PowerShare in Sleep State Allows you to enable front the USB devices to wake the system
from sleep state.
Default: Normal
Auto Power On Allows you to enable or disable Auto Power On.
Default: Disabled
Auto Power On Mode Allows you to set the computer to turn on automatically every
day or on a preselected date. This option can be configured
only if the Auto Power On mode is set to Enabled Everyday or
Selected Day.
Default: Selected Day
Auto Power On Date Allows you to set the date on which the computer must turn
on automatically. This option can be configured only if the Auto
Power On mode is set to Enabled 1 to 31.
Default: 15
88
Table 4. System setup options—Advanced menu (continued)
Advanced
Auto Power On Time Allows you to set the time at which the computer must turn on
automatically. This option can be configured only if the Auto
Power On mode is set to Enabled hh:mm:ss.
Default: 12:30:30
Numlock Key Allows you to set the status of the Num Lock key during boot to
On or Off.
Default: Enabled
Performance Options
CPU TCC offset Allows you to configure the maximum CPU temperature within a
certain range of values.
Overclocking Feature Allows you to enable or disable the Overclocking Feature.
Default: Disabled
Maintenance
Data Wipe on next boot When enabled, the BIOS will schedule a data wipe cycle for all
storage devices that are connected to the system board on the
next reboot.
Default: Disabled
BIOS Recovery from Hard Drive Enables the computer to recover from certain corrupted BIOS
conditions from a recovery file on the user primary hard drive or
an external USB key.
NOTE: BIOS Recovery from Hard Drive is not available for
Self-encrypting drives (SED).
Default: Enabled
BIOS Auto-Recovery When enabled, the autorecovery will be performed if BIOS
image integrity check fails and there is a a recovery image on
the hard drive.
NOTE: BIOS Auto-Recovery is not possible from other
media.
Default: Disabled
SupportAssist System Resolution Controls the automatic boot flow for SupportAssist System
Resolution Console and for Dell operating system Recovery tool.
Auto OS Recovery Threshold Allows you to configure the Auto OS Recovery Threshold.
Default: 2
SupportAssist OS Recovery Allows you to enable or disable the SupportAssist OS Recovery.
Default: Enabled
Table 5. System setup options—Security menu
Security
Unlock Setup Status Displays the unlock setup status.
Admin Password Status Displays whether the admin password is set.
Default: Not Set
System Password Status Displays whether the system password is set.
Default: Not Set
HDD Password Status Displays if the hard drive password is set.
89
Table 5. System setup options—Security menu (continued)
Security
Default: Not Set
Asset Tag Creates a system Asset Tag that can be used by an IT
administrator to uniquely identify a particular system. Once
set in BIOS, the Asset Tag cannot be changed.
Admin Password Enables the user to set, change, or delete the admin
password.
System Password Enables the user to set, change, or delete the system
password.
HDD Password Enables the user to set, change, or delete the hard drive
password.
Password Change Allows you to enable or disable password change on the
computer.
Default: Permitted
Absolute Enable or disable the BIOS module interface of the
optional Absolute Persistence Module service from Absolute
Software.
Default: Enabled
Firmware TPM Displays the firmware TPM state.
Default: Enabled
PPI Bypass for Clear Command Enable or disable the TPM Physical Presence Interface (PPI).
When enabled, this setting will allow the OS to skip BIOS PPI
user prompts when issuing the Clear command. Changes to
this setting take effect immediately.
Default: Disabled
UEFI Firmware Capsule Updates Enables or disables BIOS updates through UEFI capsule
update packages.
Default: Enabled
Windows SMM Security Mitigations Table Enables or disables Windows SMM Security Mitigation
protections.
Default: Disabled
Enable Pre-Boot DMA Protection Enables or disables Pre-Boot DMA Protection.
Default: Enabled
Enable OS Kernal DMA Protection Enables or disables OS Kernal DMA Protection.
Default: Enabled
Secure Boot
Secure Boot Enables secure boot using only validated boot software.
Default: Disabled
Secure Boot Mode Modifies the behavior of Secure Boot to allow evaluation
or enforcement of UEFI driver signatures. Deployed Mode
should be selected for normal operation of Secure Boot.
Default: Deployed Mode
Expert Key Management
90
Table 5. System setup options—Security menu (continued)
Security
Custom Mode Allows you to enable or disable Custom Mode. When
enabled, it allows the PK, KEK, db, and dbx security key
databases to be modified.
Default: Disabled
Enable Microsoft UEFI CA Allows you to enable or disable Microsoft UEFI CA.
PK
KEK
db
dbx
Reset all Keys
Delete all Keys
Allows for selection of key database.
●Delete All Keys will delete the selected key.
●Reset All Keys will reset all four keys to their default
settings.
Table 6. System setup options—Boot menu
Boot
Boot List Option Displays the available boot devices.
Default: UEFI
File Browser Add Boot Option Allows you to set the boot path in the boot option list.
File Browser Del Boot Option Allows you to delete the boot path in the boot option list.
Enable USB Boot Support Allows you to enable or disable the USB Boot control.
Boot Option Priorities Displays the available boot devices.
Boot Option #1 Displays the first boot device.
Default: Windows Boot Manager.
Boot Option #2 Displays the second boot device.
Default: Onboard NIC (IPV4)
Table 7. System setup options—Exit menu
Save & Exit
Save Changes and Reset Allows you to exit system setup and save your changes.
Discard Changes and Reset Allows you to exit system setup and load previous values for
all system setup options.
Restore Defaults Allows you to load default values for all system setup
options.
Discard Changes Allows you to exit your changes.
Save Changes Allows you to save your changes.
System and setup password
Table 8. System and setup password
Password type Description
System password Password that you must enter to log in to your system.
91
Table 8. System and setup password (continued)
Password type Description
Setup password Password that you must enter to access and make changes to the
BIOS settings of your computer.
You can create a system password and a setup password to secure your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data that is stored on your computer if it is not locked and left unattended.
NOTE: System and setup password feature is disabled.
Assigning a system setup password
Prerequisites
You can assign a new System or Admin Password only when the status is in Not Set.
About this task
To enter the system setup, press F12 immediately after a power-on or reboot.
Steps
1. In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2. Select System/Admin Password and create a password in the Enter the new password field.
Use the following guidelines to assign the system password:
●A password can have up to 32 characters.
●At least one special character: ! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ] ^ _ ` { | }
●Numbers 0 through 9.
●Upper case letters from A to Z.
●Lower case letters from a to z.
3. Type the system password that you entered earlier in the Confirm new password field and click OK.
4. Press Esc and save the changes as prompted by the pop-up message.
5. Press Y to save the changes.
The computer restarts.
Deleting or changing an existing system setup password
Prerequisites
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System
and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.
About this task
To enter the System Setup, press F12 immediately after a power-on or reboot.
Steps
1. In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password, update, or delete the existing system password, and press Enter or Tab.
4. Select Setup Password, update, or delete the existing setup password, and press Enter or Tab.
92
NOTE: If you change the System and/or Setup password, reenter the new password when prompted. If you delete the
System and/or Setup password, confirm the deletion when prompted.
5. Press Esc and a message prompts you to save the changes.
6. Press Y to save the changes and exit from System Setup.
The computer restarts.
Clearing CMOS settings
About this task
CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.
Steps
1. Remove the left-side cover.
2. Remove the coin-cell battery.
3. Wait for one minute.
4. Replace the coin-cell battery.
5. Replace the left-side cover.
Clearing BIOS (System Setup) and System passwords
About this task
To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.
NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying Windows
or your application.
Updating the BIOS
Updating the BIOS in Windows
Steps
1. Go to www.dell.com/support.
2. Click Product support. In the Search support box, enter the Service Tag of your computer, and then click Search.
NOTE: If you do not have the Service Tag, use the SupportAssist feature to automatically identify your computer. You can
also use the product ID or manually browse for your computer model.
3. Click Drivers & Downloads. Expand Find drivers.
4. Select the operating system installed on your computer.
5. In the Category drop-down list, select BIOS.
6. Select the latest version of BIOS, and click Download to download the BIOS file for your computer.
7. After the download is complete, browse the folder where you saved the BIOS update file.
8. Double-click the BIOS update file icon and follow the on-screen instructions.
For more information, see knowledge base article 000124211 at www.dell.com/support.
Updating the BIOS using the USB drive in Windows
Steps
1. Follow the procedure from step 1 to step 6 in Updating the BIOS in Windows to download the latest BIOS setup program file.
93
2. Create a bootable USB drive. For more information, see the knowledge base article 000145519 at www.dell.com/support.
3. Copy the BIOS setup program file to the bootable USB drive.
4. Connect the bootable USB drive to the computer that needs the BIOS update.
5. Restart the computer and press F12 .
6. Select the USB drive from the One Time Boot Menu.
7. Type the BIOS setup program filename and press Enter.
The BIOS Update Utility appears.
8. Follow the on-screen instructions to complete the BIOS update.
Updating the BIOS from the F12 One-Time boot menu
Update your computer BIOS using the BIOS update.exe file that is copied to a FAT32 USB drive and booting from the F12
One-Time boot menu.
About this task
BIOS Update
You can run the BIOS update file from Windows using a bootable USB drive or you can also update the BIOS from the F12 One-Time
boot menu on the computer.
Most of the Dell computers built after 2012 have this capability, and you can confirm by booting your computer to the F12 One-Time
Boot Menu to see if BIOS FLASH UPDATE is listed as a boot option for your computer. If the option is listed, then the BIOS supports
this BIOS update option.
NOTE: Only computers with BIOS Flash Update option in the F12 One-Time boot menu can use this function.
Updating from the One-Time boot menu
To update your BIOS from the F12 One-Time boot menu, you need the following:
●USB drive formatted to the FAT32 file system (key does not have to be bootable)
●BIOS executable file that you downloaded from the Dell Support website and copied to the root of the USB drive
●AC power adapter that is connected to the computer
●Functional computer battery to flash the BIOS
Perform the following steps to perform the BIOS update flash process from the F12 menu:
CAUTION: Do not turn off the computer during the BIOS update process. The computer may not boot if you turn off your
computer.
Steps
1. From a turn off state, insert the USB drive where you copied the flash into a USB port of the computer.
2. Turn on the computer and press F12 to access the One-Time Boot Menu, select BIOS Update using the mouse or arrow keys then
press Enter.
The flash BIOS menu is displayed.
3. Click Flash from file.
4. Select external USB device.
5. Select the file and double-click the flash target file, and then click Submit.
6. Click Update BIOS. The computer restarts to flash the BIOS.
7. The computer will restart after the BIOS update is completed.
94
Troubleshooting
SupportAssist diagnostics
About this task
The SupportAssist diagnostics (previously known as ePSA diagnostics) performs a complete check of your hardware. The
SupportAssist diagnostics is embedded in the BIOS and is launched by it internally. The SupportAssist diagnostics provides a set
of options for particular devices or device groups. It allows you to:
●Run tests automatically or in an interactive mode.
●Repeat tests
●Display or save test results
●Run thorough tests to introduce additional test options and provide extra information about the failed device(s)
●View status messages that indicate if the tests are completed successfully
●View error messages that indicate if problems were encountered during the test
NOTE: Some tests are meant for specific devices and require user interaction. Ensure that you are present in front of the
computer when the diagnostic tests are performed.
For more information, see SupportAssist Pre-Boot System Performance Check.
System-diagnostic lights
The power-status light indicates the power status of the computer. These are the power states:
Solid white—Computer is in S0 state. This is the normal power state of the computer.
Blinking white—Computer is in Modern Standby mode. This does not indicate a fault.
Solid amber—Computer is experiencing a boot failure, including the power-supply unit.
Blinking amber—Computer is experiencing a boot failure but the power-supply unit is functioning correctly.
Off—Computer is in hibernation mode or turned off.
The power-status light may also blink amber or white according to predefined "beep codes" indicating various failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times
followed by a pause. This 2,3 pattern continues until the computer is turned off, indicating no memory or RAM is detected.
The following table shows different power and battery-status light patterns and associated problems.
NOTE: The following diagnostic light codes and recommended solutions are intended for Dell service technicians to
troubleshoot problems. You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Table 9. Diagnostic light codes
Diagnostic light codes (Amber, White) Problem description
1,1 TPM Detection Failure
1,2 Unrecoverable SPI Flash Failure
1,5 EC unable to program i-Fuse
1,6 Generic catch-all for ungraceful EC code flow errors
1,7 Non-RPMC Flash on Boot Guard fused system
2,1 CPU configuration or CPU failure
2,2 System board: BIOS or Read-Only Memory (ROM) failure
2,3 No memory or Random-Access Memory (RAM) detected
2,4 Memory or Random-Access Memory (RAM) failure
95
Table 9. Diagnostic light codes (continued)
Diagnostic light codes (Amber, White) Problem description
2,5 Invalid memory installed
2,6 System board/Chipset Error
3,1 CMOS battery failure
3,2 PCI of Video card/chip failure
3,3 BIOS Recovery 1: BIOS recovery image not found
3,4 BIOS Recovery 2: Recovery image found but invalid
3,5 Power Rail Failure: EC ran into power sequencing failure
3,6 Flash corruption detected by SBIOS
4,1 Memory DIMM power rail failure
4,2 CPU Power cable connection issue
Recovering the operating system
When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell
SupportAssist OS Recovery.
Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows operating
system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating system. It
enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its factory state.
You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their primary
operating system due to software or hardware failures.
For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at www.dell.com/
serviceabilitytools. Click SupportAssist and then, click SupportAssist OS Recovery.
WiFi power cycle
About this task
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be performed.
The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Steps
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
Drain residual flea power (perform hard reset)
About this task
Flea power is the residual static electricity that remains in the computer even after it has been powered off and the battery is
removed.
96
For your safety, and to protect the sensitive electronic components in your computer, you are requested to drain residual flea power
before removing or replacing any components in your computer.
Draining residual flea power, also known as a performing a "hard reset", is also a common troubleshooting step if your computer does
not power on or boot into the operating system.
To drain residual flea power (perform a hard reset)
Steps
1. Turn off your computer.
2. Disconnect the power adapter from your computer.
3. Press and hold the power button for 20 seconds to drain the flea power.
4. Connect the power adapter to your computer.
5. Turn on your computer.
NOTE: For more information about performing a hard reset, see the knowledge base article 000130881 at www.dell.com/
support.
Modern Standby
What is Modern Standby
Alienware Aurora Ryzen Edition R14 supports Modern Standby. It is a power model that uses a gradual process to turn off
components of the computer. This process allows for a quicker transition between sleep and resumption of normal operation of the
computer.
For more information about the Modern Standby mode, see the following:
●What is Modern Standby and how does it differ from S3 Standby?
●What is Modern Standby?
●Modern Standby versus S3
●Modern Standby States
97
Getting help and contacting Alienware
Self-help resources
You can get information and help on Alienware products and services using these online self-help resources:
Table 10. Alienware products and online self-help resources
Self-help resources Resource location
Information about Alienware products and services www.alienware.com
My Dell app
Tips
Contact Support In Windows search, type Contact Support, and press Enter.
Online help for operating system www.dell.com/support/windows
Access top solutions, diagnostics, drivers and downloads, and
learn more about your computer through videos, manuals and
documents.
Your Alienware computer is uniquely identified by a Service Tag
or Express Service Code. To view relevant support resources for
your Dell computer, enter the Service Tag or Express Service
Code at www.dell.com/support.
For more information on how to find the Service Tag for your
computer, see Locate the Service Tag on your computer.
VR Support www.dell.com/VRsupport
Videos providing step-by-step instructions to service your
computer
www.youtube.com/alienwareservices
Contacting Alienware
To contact Alienware for sales, technical support, or customer service issues, see www.alienware.com.
NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.
NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice, packing
slip, bill, or Dell product catalog.
98