Table of Contents
- CL1008 / CL1016 User Manual
- Introduction
- Hardware Setup
- Basic Operation
- OSD Operation
- Hotkey Operation
- The Firmware Upgrade Utility
- Appendix
- Index
ATEN CL1008M-AT-US User Manual
Displayed below is the user manual for CL1008M-AT-US by ATEN which is a product in the KVM Switches category. This manual has pages.
Related Manuals
LCD KVM Switch
CL1008 / CL1016
User Manual
www.aten.com
CL1008 / CL1016 User Manual
ii
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installe d and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at their own expense.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
CE Warning:
This is a class A product. In a domestic environment this product ma y cause
radio interference in which case the user may be required to take adequate
measures.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
KCC Statement
유선 제품용 /A급 기기 (업무용 방송 통신 기기 )
이 기기는 업무용 (A 급)전자파적합기기로서 판매자 또는 사용자는 이
점을 주의하시기 바라며 ,가정 외의 지역에서 사용하는 것을 목적으로
합니다 .
RoHS
This product is RoHS complian t.
CL1008 / CL1016 User Manual
iii
SJ/T 11364-2006
The following contains information that relates to China.
CL1008 / CL1016 User Manual
iv
User Information
Online Registration
Be sure to register your product at our on line support center:
Telephone Support
For telephone support, call this num ber:
User Notice
All information, docu men tation, and specifications containe d in thi s m anual
are subject to change without prior notificatio n by the m a nufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particu lar purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the progr ams pro ve defectiv e following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PL EASE VERIFY THAT THE VOLTAGE S E TTING IS
CORRECT BEFORE USE.
International http://eservice.aten.com
International 886-2-8692-6959
China 86-10-5255-0110
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
United Kingdom 44-8-4481-58923
CL1008 / CL1016 User Manual
v
Package Contents
Basic Package
The basic CL1008 or CL1016 package consists of:
1 CL1008 or CL1016 with Standard Rack Mount Kit
2 Custom KVM Cable Sets
1Power Cord
1 Firmware Upgrade Cable
1 Quick Start Guide
Optional Equipment
Depending on any optional equipment that you may have purchased, one of the
following may be included in your pack age:
Standard Rack Mounting Kit - Long
Easy-Installation Rack Mounting Kit - Short
Easy-Installation Rack Mounting Kit - Long
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encount er a prob lem, cont act your dealer.
Read this manual thorough ly and follow the installation and op erati on
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
*Features may have been added to the CL1008 / CL1016 since this man ual
was printed. Please visit our website to download the most up-to-date version
of the manual.
© Copyright 2008–2015 ATEN® International Co., Ltd.
Manual Date: 2015-04-24
ATEN and the A TEN logo are registered tr ademarks of ATEN International Co. , Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
CL1008 / CL1016 User Manual
vi
Contents
EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Basic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
About this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
1. Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
OS Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. Hardware Setup
Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Standard Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Single Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Daisy Chain Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3. Basic Operation
Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
The LCD Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LCD Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Manual Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CL1008 / CL1016 User Manual
vii
4. OSD Operation
OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
OSD Main Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
F2: LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
F3: SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
F6: BRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
F8: LOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
5. Hotkey Operation
Hotkey Port Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Invoking Hotkey Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Exiting Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Hotkey Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Hotkey Mode Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Selecting the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Setting the Scan Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Invoking Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Pausing Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Exiting AutoScan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Hotkey Summary Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
6. The Firmware Upgrade Utility
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Consignes de sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
CL1008 / CL1016 User Manual
viii
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
CL1008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
CL1016 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
CL1008 – ACS1208A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
CL1008 – ACS1216A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
CL1016 – ACS1208A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
CL1016 – ACS1216A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Clear Login Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Optional Rack Mounti ng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Standard - Long . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Easy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Dedicated Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
CL1008 / CL1016 User Manual
ix
About this Manual
This User Manual is provided to help you get the most from your CL1008 /
CL1016 system. It covers all aspects of installation, configuration and
operation. An overview of the information found in the manual is provided
below.
Chapter 1, Introduction, introduces you to the CL1008 / CL1016 system.
Its purpose, features and benefits are presented, and its front and back panel
components are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary step – from a basic single stage hookup to a complete 16 switch daisy
chained operation are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the CL1008 / CL1016.
Chapter 4, OSD Operation, provides a complete descrip tion of the
CL1008 / CL1016's OSD (on-screen display), and how to work with it.
Chapter 5, Hotkey Operation, details all of the concepts and procedures
involved in the Hotkey operation of your CL1008 / CL1016 installation.
Chapter 6, The Firmware Upgrade Utility, explains how to use this
utility to upgrade the CL1008 / CL1016's firmware with the latest availa ble
versions.
An Appendix, provides specifications and other technical information
regarding the CL1008 / CL1016.
CL1008 / CL1016 User Manual
x
Conventions
This manual uses the following conven tions:
Product Information
For information about all ATEN products and how they can help you connect
without limits, vi si t ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a li st of locations and telephone numbers:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start → Run means to
open the Start menu, and then select Run.
Indicates critical information.
International http://www.aten.com
North America http://www.aten-usa.com
1
Chapter 1
Introduction
Overview
The CL1008 / CL1016 SlideawayTM LCD KVM Switch series are control units
that allow access to multiple computers from a single keyboard, video, and
mouse (KVM) console. A single CL1008 or CL1016 can control up to 8 or 16
computers. As many as 15 additional KVM switches can be daisy chained to
the CL1008 / CL1016, so that up to 256 computers can all be controlled from
a single KVM console.
The CL1008 / CL1016 offers a space-saving, streamlined approach to KVM
switch technology by integrating a keyboard, LCD monitor, and touchpad in a
1U rack-mountable sliding housing. The LCD display is built into the cover;
the keyboard and touchpad are built into the base. Slide the KVM module
section out; flip the cover up; and you are ready to work. When finished, flip
the cover down and slide the KVM module away.
The CL1008 / CL1016 is built on a modular design. The KVM section can be
detached from the switch section for convenient maintenance and repair.
Your CL1008 / CL1016 investment is protected by an included Firmware
Upgrade Utility. You can stay current with the latest improvements to the
switch by downloading firmware update files from our website as they become
available, and using the utility to quick ly and conv eniently perform the
upgrade.
Setup is fast and easy; plugging cables into their appropriate ports is all that is
entailed. Because the CL1008 / CL1016 intercepts keyboard input directly,
there is no software to configure; no need to get involved in complex
installation routines; nor any need to be concerned wit h incom pat ibility
problems.
Access to any computer connected to the installation is easily accomplished
either by entering hotkey combinati ons from the keybo ard, or by means of a
powerful, mouse driven, on-screen display (OSD) menu system. A convenient
Auto Scan feature also permits automatic scanning and monitoring of the
activities of all computers running on the installa tion one by one.
CL1008 / CL1016 User Manual
2
Features
Exclusive LED illumination light - designed by ATEN to illuminate the
keyboard and touchpad to allow visib ility in low-light conditio ns
KVM console with 17" LED-backlit LCD monitor in a sliding housing –
top and bottom clearance for smooth operation in a 1U high system rack
LCD module rotates up to 115o for a more comfortable viewing angle
Standard rack mount kit included – optional Easy Rack Mounting (single
person installation) rack mount kit available (requires separate purchase)
Daisy chain up to 15 additional units – control up to 128 (CL1008) or 256
(CL1016) computers
No software required – convenient computer selection via hotkeys and
mouse driven intuitive on-screen display (OSD) menu s
Auto Scan feature for monitoring user-selected computers
Broadcast support – commands from the keyboard can be broadcast to all
available computers on the installation
Hot pluggable – add or remove computers without having to power down
the switch
Two level password security – only authorized users view and control the
computers – up to four users plus an administrator with separate profiles
for each
Video settings of attached computers are automatically adjusted for
optimal output to the LCD monitor
Upgradable firmware
Keyboard language support: English (US), English (UK), French,
German, German (Swiss), Hungarian, Italian, Japanese, Korean, Russian,
Spanish, Swedish and Traditional Chinese
1. Introduction
3
Requirements
Computers
The following equipment must be installed on each computer:
A VGA, SVGA or multisync card
Note: The integrated LCD monitor's maximu m resolution is
1280 x 1024 @ 75 Hz. Make sure that none of the computer
resolution settings exceed the LCD monitor's maximum resolution.
6-pin Mini-DIN (PS/2 style) keyboard and mouse ports
Cables
Substandard cables may damage the connected devices or degrade overall
performance. For optimum signal int egri ty and to simplify the layout, we
strongly recommend that you use the high quality CS Custom Cable sets
described below:
Function Part Number Length
Daisy-chain Cables 2L-1700 0.6 m
2L-1701 1.8 m
2L-1703 3.0 m
2L-1705 5.0 m
2L-1715 15.0 m
KVM Switch to Computer 2L-5201P 1.2 m
2L-5202P 1.8 m
2L-5702P 1.8 m
2L-5203P 3.0 m
2L-5206P 6.0 m
2L-5202UP 1.8 m
2L-5203UP 3.0 m
2L-5205UP 5.0 m
2L-5206UP 6.0 m
CL1008 / CL1016 User Manual
4
OS Support
Components
Front View
OS Version
Windows 2000 and higher
Linux RedHat 7.1–7.3, 8.0, 9.0, Fedora Core 2–4
SuSE 8.2, 9.3, 10
Mandriva (Mandrake) 9, 2005 Limited Edition, 2006
UNIX IBM AIX: 4.3, 5L
FreeBSD 4.2, 4.5
Novell Netware: 5.0, 6.0
9
2
1
2
4
3
5
6
14
13
12
11
10
8
7
EXIT I LIGHT
Press the Exit/Light pushbutton for
two seconds to turn the LED light
ON or O. (Default: On)
1. Introduction
5
No. Component Description
1 Handle Pull to slide the KVM module out; push to slide the module in
(see item 2 in this table).
2 Slide Release In order to slide the console out, you must first release it by
sliding these tabs to the inside. See page 15 for details on
sliding the console in and out.
3 LCD Display After sliding the KVM module out, flip up the cover to access
the LCD monitor.
4 LCD Controls The LCD On/Off switch is located here, as well as buttons to
control the position and picture settings of the LCD display.
See page 19 for details.
5 Port Switches Press a switch to bring the KVM focus to the computer
attached to its corresponding port. See page 21 for details.
6 Keyboard Standard mouse touchpad
7 Touchpad Standard 105-key keyboard
8 Port LEDs Two Port LEDs are built into the Port Switches. The one on
the left is the On Line LED; the one on the right is the
Selected Port LED:
An On Line LED lights ORANGE to indicate that the
computer attached to its corresponding port is up and
running.
A Selected LED lights GREEN to indicate that the
computer attached to its corresponding port has the KVM
focus. The LED is steady under normal conditions, but
flashes when its port is accessed under Auto Scan Mode
(see F7: SCAN, page 35).
9LED
Illumination
Light
Press the Exit/Light pushbutton for two seconds to turn the
LED light ON or Off. (Default: On)
10 Power LED Lights DARK GREEN to indicate that the unit is receiving
power.
11 Rack Mounting
Brackets The rack mounting brackets located at each corner of the unit
secure the chassis to a system rack.
12 Lock LEDs The Num Lock, Caps Lock, Scroll Lock LEDs are located
here.
13 Reset Switch Located to the right of the Lock LEDs. Press this recessed
switch in with a small object to perform a system reset.
CL1008 / CL1016 User Manual
6
14 Firmware
Upgrade
Section
Firmware Upgrade Port: The Firmware Upgrade Cable
that transfers the firmware upgrade data from the
administrator's computer to the CL1008 / CL1016 plugs
into this RJ-11 connector.
Firmware Upgrade Switch: During normal operation this
switch should be in the NORMAL position. (See p. 43 for
firmware upgrading details.)
No. Component Description
1. Introduction
7
Rear View
Note: The CL1016 is pictured above. The CL1008 rear panel is the same as
that of the CL1016, except that it has 8 KVM ports instead of 16.
No. Component Description
1 Daisy Chain Port When daisy chaining units, the cable plugs in here.
2 KVM Port
Section The cables that link to the computers plug in here.
Note: The shape of these SPHD connectors has been
specifically modified so that only KVM cables designed to
work with this switch can plug in (see the Cables section on
page 3, for details). Do NOT attempt to use ordinary 15 pin
VGA connector cables to link these ports to the computers.
3 Power Socket This is a standard 3-prong AC power socket. The power cord
from an AC source plugs in here.
4 Power Switch This standard rocker switch powers the unit on and off.
1
2
34
CL1008 / CL1016 User Manual
8
This Page Intentionally Left Blank
9
Chapter 2
Hardware Setup
Before you Begin
Standard Rack Mounting
A standard rack mounting kit is provided with your CL1008 / CL1016. The kit
enables the switch to be mounted in rack with a depth of 42.0–82.0 cm.
Note: 1. It takes two people to mount the switch: one to hold it in place, the
other to screw it in.
2. The standard rack mounting kit does not include screws or cage nuts.
If you need additional screws or cage nuts, contact your rack dealer.
3. Optional mounting kits – including single person Easy Installation
kits – are available with a separate purchase. See Optional Ra ck
Mounting, p. 62 for details.
1. Important safety information regarding the placement of this
device is provided on page 49. Please review it before proceeding.
2. Make sure that power to all the devices you will be connecting up
have been turned off. You must unplug the power cords of any
computers that have the Keyboard Power On function.
L Brackets
Side Mountng
Brackets
CL1008 / CL1016 User Manual
10
To rack mount the switch, do the following:
1. While one person positions the switch in the rack and holds it in place, the
second person loosely screws the front brackets to the rack.
2. While the first person still holds the switch in place, the second person
slides the L brackets into the switch's side mounting brackets, from the
rear until the bracket flanges contact the rack, then screws the L brackets
to the rack.
3. After the L brackets have been secured, tighten the front bracket screws.
Note: Allow at least 5.1 cm on each side for proper ventilation, and at least
12.7 cm at the back for the power cord and cable clearance.
2. Hardware Setup
11
Single Stage Installation
In a single stage installation, there are no additional switches daisy chained
down from the first unit. To set up a single stage installation, refer to the
installation diagram on the next page (the numbers in the diagram correspond
to the numbers of the installation steps), and do the following:
1. For each of the computers you are installing, use a KVM cable set (as
described in the Cables section on page 3) to connect any available KVM
port to the computer's keyboard, video and mouse ports.
Note: Ignore the daisy chain port at this time. It is only used when daisy
chaining additional units. Daisy chaining is described in the next
section.
2. Use the power cord provided with this package to connect the switch's
power socket to an AC power source.
This completes the installation. Now, you can power on the switch
(see Powering Up, page 18 for details). After the switch is powered on, power
on the computers.
CL1008 / CL1016 User Manual
12
Note: The CL1016 is pictured above. The CL1008 rear panel is the same as
that of the CL1016, except that it has 8 KVM ports instead of 16.
1
2
1
2. Hardware Setup
13
Daisy Chain Installation
To control even more computers, up to 15 ACS1208A or ACS1216A KVM
switches can be daisy chained down from the CL1008 / CL1016.
In a complete installation, as many as 248 or 256 computers can be controlled
from the CL1008 / CL1016. Tables showing the relation between the number
of computers and the number of units needed to control them are provided on
page 59.
To set up a daisy chained installation, first make sure that power to all the
devices you will be connecting up has been turned off. Then, refer to the daisy
chain installation diagram on the next page as you do the followin g:
1. Use a daisy chain cable set (described in the Cables section, page 3), to
connect the Chain Out port of the parent unit to the Ch ain In port of the
child unit (first station ou t to second station in, second station out to thi rd
station in, etc.).
2. Use KVM cable sets (described in the Cables section of the ACS1208A /
ACS1216A user manual), to connect any available KVM Port on the daisy
chained switch to the keyboard , vid eo and mouse ports of the computers
you are installing.
3. Repeat the above steps for any additional units you wish to add to the chain.
CL1008 / CL1016 User Manual
14
Note: The CL1016 is pictured above. The CL1008 rear panel is the same as
that of the CL1016, except that it has 8 KVM ports instead of 16.
CL1016
ACS1216A
ACS1216A
15
Chapter 3
Basic Operation
Opening the Console
The CL1008 / CL1016's console is located under the top cover. As a safety
precaution, the console is locked into the In position. To access the console,
push the release catches on the unit's front panel toward the center of the
switch; pull the module ou t; and raise the cover.
CL1008 / CL1016 User Manual
16
Closing the Console
To slide the console module in, close the cover and do the following :
1. Pull the safety catches on the unit's side rails toward you and push the
module in until it stops.
2. Release the catches; pull the module slightly toward you; then push it all
the way in.
Note: The reason for the two step procedure is to minimize the chances of
getting your fingers pinched when sliding the mod ule in.
3. Basic Operation
17
Operating Precautions
Right!
Rest your hands and arms lightly on the
keyboard module as you work.
Wrong!
DO NOT lean your body weight on the
keyboard module.
DO NOT place heavy objects on the
keyboard module.
The maximum load bearing capacity of the keyb oard module is
30 kg. Failure to heed the information below can result in damage
to the keyboard module.
CL1008 / CL1016 User Manual
18
Powering Up
Power up the installation according to the following procedure:
1. Power on the first station (CL1008 / CL1016) and wait a few seconds for
the unit to ascertain its station ID.
2. Plug in the power adapters for each daisy chained station on the
installation in turn (second statio n, then thi rd stat ion, etc.).
Each ACS1208A / ACS1216A has a LED display on its front panel to
indicate its station ID (the station ID for the first stage unit is 01, the ID for
the second stage unit is 02, the ID for the third stage unit is 03, etc.).
In each case, wait for the station ID to be ascertaine d and displayed on the
station ID LED before plugging in the next station.
3. After all the stations are up, power on the computers.
Powering Off and Restarting
If it becomes necessary to power off the CL1008 / CL1016, or if the switch
loses power and needs to be restarted, wait 10 seconds before powering it back
on. The computers should not be affected by this, but if any of them should fail,
simply restart the affected computers.
3. Basic Operation
19
LCD OSD Configuration
The LCD Buttons
The LCD OSD allows you to set up and configure the LCD display. Four
buttons are used to perform the configuration, as described in the table, below:
Button Function
MENU When you have not entered the LCD OSD Menu function,
pressing this button invokes the Menu function, and brings up
the Main Menu.
When you have entered the LCD OSD Menu function, and
have reached a setting choice with the navigation buttons,
pressing this button brings up its adjustment screen.
When navigating through the menus, this button moves you Right
or Up. When making an adjustment, it increases the value.
When navigating through the menus, this button moves you Left
or Down. When making an adjustment, it decreases the value.
EXIT When you have not entered the LCD OSD Menu function,
pressing this button performs an auto adjustment. An auto
adjustment automatically configures all the settings for the
LCD panel to what the OSD considers their optimum values to
be.
When you have entered the LCD OSD Menu function, pressing
this button exits the current menu and returns you to the
previous menu. Use it to leave an adjustment menu when you
are satisfied with the adjustment you made.
When you are at the Main Menu, pressing this button exits the
LCD OSD.
CL1008 / CL1016 User Manual
20
LCD Adjustment Settings
An explanation of the LCD OSD adjustment settings is given in the table
below:
Setting Explanation
Brightness Adjusts the background black level of the screen image.
Contrast Adjusts the foreground white level of the screen image.
Phase If pixel jitter or horizontal line noise is visible on the display,
your LCD may have the wrong phase setting. Adjust the
phase setting to eliminate these problems.
Clock If vertical banding is visible on the display, your LCD may
have the wrong clock setting. Adjust the clock setting to
eliminate vertical banding.
H-Position Positions the display area on the LCD panel horizontally
(moves the display area left or right).
V-Position Positions the display area on the LCD panel vertically
(moves the display area up or down).
Color Temperature Adjusts the color quality of the display. You can adjust the
warmth value, color balance, etc. The Adjust Color
selection has a further submenu that lets you fine tune the
RGB values.
Language Selects the language that the OSD displays its menus in.
OSD Duration Lets you set the amount of time the OSD displays on the
screen. If there is no input for the amount of time you
choose, the OSD display turns off.
Reset Resets the adjustments on all menus and submenus to
their factory default settings.
Note: The Language setting does not return to the factory
default, but remains at the one that you have set it to.
3. Basic Operation
21
Port ID Numbering
Each KVM port on the installation is assigned a unique Port ID. The Port ID is
made up of two parts: a Station Number, and a Port Number:
The Station Numb er – is a two dig it number which reflects the switch's
position in the daisy chain sequence.
Note: 1. The first station CL1008 / CL1016 has a station number of 01.
The first daisy chained unit has a station number of 02, etc.
2. The daisy chained switches have front panel LEDs that display
their station IDs.
The Port Number – is a two digit number which reflects the port on the
station that the computer is connected to.
The station number precedes the Port Number.
Station and port numbers from 1–9 are padded with a preceding zero, so
they become 01–09.
For example, a computer attached to Port 6 of Station 12 would have a port
ID of 12-06.
Port Selection
The CL1008 / CL1016 provides th ree port selection methods you can use to
access the computers on the installation: manual; OSD menus, and hotkey.
Manual port switching is discussed below; OSD operation is discussed in the
next chapter; hotkey port selection is discussed in Chapter 5.
Manual Port Switching
Press a switch to bring the KVM focus to the computer attached to its
corresponding port.
Press buttons 1 and 2 simultaneously for two seconds to perform a
keyboard and mouse reset.
Press buttons 7 and 8 (CL1008), or 15 and 16 (CL1016) simultaneously
for two seconds to invoke Auto Sca n Mode (see p. 39).
CL1008 / CL1016 User Manual
22
Hot Plugging
The CL1008 / CL1016 supports hot plugging – computers can be removed and
added back into the installat ion by unplugging and replugging their cables
from/into the switch’s KVM ports.
In order for the switch’s OSD menus to correspond to the change, how ever,
you must manually reconfigure the OSD to reflect the new port inform ation.
See F3: SET, page 28, and F4: ADM, page 30, for details.
Note: If the computer's operating system does not support hot pl ugging, this
function may not work properly.
23
Chapter 4
OSD Operation
OSD Overview
The on-screen display (OSD) is a menu driven method to handle computer
control and switching operations. All procedures start from the OSD main
screen.
There are two ways to invoke the OSD:
1. Tap the OSD invocation key on the keyboard (see p. 60), or
2. Tap the [Scroll Lock] key twice.
Note: Scroll Lock] is the default OSD hotkey. You can optionally change the
OSD Hotkey to the Ctrl key (see OSD Hotkey, page 28), in which case
you would press [Ctrl] twice. If you choose this method, you must press
the same [Ctrl] key both times.
Logging In
The OSD incorporates a two level (administrator / user) authorization
procedure. Before the OSD main screen comes up, a login dialog box appears
requesting a username and password.
If this is a first time log in, or if the password function has not been set, simply
press [Enter]. The OSD main screen displays in administrator mode. In this
mode, you have administrator privileges, with access to all administrator and
user functions, and can set up operations (including password authorization) as
you like.
If the password function has been set, you must provide a valid username and
password in order to access the OSD.
CL1008 / CL1016 User Manual
24
OSD Main Screen
When you invoke the OSD, a screen similar to the one below appears:
Note: 1. The diagram depicts the administrator's main screen. The user main
screen does not show the F4 and F6 functions since these are reserved
for the administrator and can't be accessed by users.
2. The OSD always starts in List view, with the highlight bar at the same
position it was in the last time it was closed.
3. Only the ports that have been set accessible by the administrator for
the currently logged in user are visible (see SET ACCESSIBLE
PORTS, page 32, for details).
F1:GOTO F3:SET F5:SKP F7:SCAN X
F2:LIST F4:ADM F6:BRC F8:LOUT
z
z
z
ADMINISTRATOR
LIST:ALL
SN PN QV NAME
01 14 ATEN INTL.CO. 1
01 15 ATEN INTL.CO. 2
01 16 ATEN INTL.CO. 3
02 01 FAX SERVER 1
02 02 FAX SERVER 2
02 03 WEB SERVER 1
02 04 WEB SERVER 2
02 05 MAIL SERVER 1
Chapter 4. OSD Operation
25
OSD Main Screen Headings
OSD Navigation
To di sm iss the menu, and deactivate the OSD, Click the X at the upper
right corner of the OSD window; or press [Esc].
To Logo ut, click F8 or the ZZZ symbol at the top of the main screen, or
press [F8].
To m ove up or down through the list one line at a time, click the up or
down symbols (ST) or use the up or down arrow keys. If there are more
list entries than there is room for on the main screen, the screen will scroll.
To m ove up or down through the list one screen at a time, click the up or
down arrow symbols (ÏÐ), or use the [Pg Up] or [Pg Dn] keys. If there
are more list entries than there is room for on the main screen, the screen
will scroll.
To bring the KVM focus to a port, double click it, or move the highlight
bar to it then press [Enter].
Heading Explanation
SN-PN This column lists the port ID numbers (station number - port number)
for all the KVM ports on the installation. The simplest method to access
a particular computer is to click it, or move the highlight bar to it, then
press Enter.
QV If a port has been selected for quick view scanning (see Set Quick
View Ports, page 32), an arrowhead displays in this column.
The computers that are powered on and are on line have a sun symbol
in this column.
NAME If a port has been given a name (see Edit Port Names, page 31), its
name appears in this column.
CL1008 / CL1016 User Manual
26
OSD Functions
OSD functions are used to configure and control the OSD. For example, you
can: rapidly switch to any port, scan selected ports only, limit the list you wish
to view, designate a port as a quick view port, create or edit a port name, or
make OSD setting adjustments.
To access an OSD function:
1. Either click a function key field at the top of the main screen, or press a
function key on the keyboard.
2. In the submenus that appear make your choice either by double clicking it,
or moving the highlight ba r to it , then pressing [Enter].
3. Press [Esc] to return to the previous menu level.
F1: GOTO
GOTO allows you to switch directly to a port eit her by keying in the port's
Name, or its Port ID.
To use the name method, key in 1; key in the port's name; then press
[Enter].
To use the port ID me thod , key in 2; key in the Port ID; then press
[Enter].
Note: You can key in a partial name or port id, in which case the screen will
show all the computers that the user has View rights to (see SET
ACCESSIBLE PORTS, page 32) that match the name or port ID pattern,
regardless of the current List settings (see F2 LIST , page 27, for details).
To return to the OSD main screen without making a choice, press [Esc].
Chapter 4. OSD Operation
27
F2: LIST
This function lets you broaden or narrow the scope of ports the OSD displays
on the main screen. Many of the OSD functions only operate on the computers
currently selected for listing on the main screen with this function. The
submenu choices and their meanings are given in the table below:
Double click the choice you want, or move the highlight bar to it, then press
[Enter]. An icon appears before the choice to indicate that it is the currently
selected one.
Choice Meaning
ALL Lists all of the ports on the installation.
QUICK VIEW Lists only the ports that have been selected as quick view port s (see
SET ACCESSIBLE PORTS, page 32).
POWERED ON Lists only the ports that have their attached computers powered on.
QUICK VIEW +
POWERED ON Lists only the ports that have been selected as quick view port s (see
SET QUICK VIEW PORTS, page 32), and that have their attached
computers powered on.
CL1008 / CL1016 User Manual
28
F3: SET
This function allows the administrator and each user to set up their own,
individual, working environm ent. A separate profile for each is stored by the
OSD and is activated according to the username provided during login.
To change a setting:
1. Double click it; or move the highlight bar to it, then press [Enter].
2. After you select an item, a submenu with further choices appears. To make
a selection, either double click it; or move the highlight bar to it, then press
[Enter]. An icon appears before the selected choice to indicate which one
it is. The settings are explained in the following table:
(Continues on next page.)
Setting Function
OSD HOTKEY Selects which hotkey activates the OSD function:
[Scroll Lock] [Scroll Lock] or [Ctrl] [Ctrl].
Since the [Ctrl] key combination may conflict with programs running
on the computers, the default is the [Scroll Lock] combination.
PORT ID
DISPLAY
POSITION
Allows you to position where the port ID appears on the monitor.
The default is the upper left corner, but you can have it appear
anywhere on the screen.
Use the mouse or the arrow keys to position the port ID display,
then click or press [Enter] to lock the position and return to the Set
submenu.
PORT ID
DISPLAY
DURATION
Determines how long a port ID displays on the monitor after a port
change has taken place. The choices are: User Defined – which
lets you select the amount of time (from 1–255 sec.); and Always
On – which displays the port ID at all times. If you select User
Defined, key in the number of seconds, then press [Enter]. The
default is 3 Seconds. A setting of 0 (zero) disables this function.
Chapter 4. OSD Operation
29
(Continued from previous page.)
Setting Function
PORT ID
DISPLAY
MODE
Selects how the port ID is displayed: the port number alone (PORT
NUMBER); the port name alone (PORT NAME); or the port
number plus the port name (PORT NUMBER + PORT NAME). The
default is PORT NUMBER + PORT NAME).
SCAN
DURATION Determines how long the focus dwells on each port as it cycles
through the selected ports in Auto Scan mode (see F7 SCAN,
page 35). Key in a value from 1–255 seconds, then press [Enter].
Default is 5 seconds; a setting of 0 disables the scan function.
SCAN/SKIP
MODE Selects which computers will be accessed under Skip mode (see
F5 SKP, page 33), and Auto Scan mode (see F7 SCAN, page 35).
Choices are:
ALL – All the ports which have been set accessible (see SET
ACCESSIBLE PORTS, page 32);
QUICK VIEW – Only those ports which have been set accessible
and have been selected as quick view ports (see SET QUICK
VIEW PORTS, page 32);
POWERED ON – Only those ports which have been set accessible
and are powered on;
QUICK VIEW + POWERED ON – Only those ports which have
been set accessible and have been selected as quick view ports
and are powered on. The default is ALL.
SCREEN
BLANKER If there is no input from the console for the amount of time set with
this function, the screen is blanked. Key in a value from
1–30 minutes, then press [Enter]. A setting of 0 disables this
function. The default is 0 (disabled).
HOTKEY
COMMAND
MODE
Enables / Disables the Hotkey Command function. If the hotkey
combinations conflict with programs running on the computers, you
may want to disable hotkey operation by turning Hotkey Command
mode Off. The default is ON, which allows hotkey operation of the
switch.
CL1008 / CL1016 User Manual
30
F4: ADM
F4 is an administrator only function. It allows the administrator to configure
and control the overall operation of the OSD. To change a setting double click
it; or use the up and down arrow keys to move the highlight bar to it then press
[Enter].
After you select an item, a submenu with further choices appears. Double click
an item, or move the highlight bar to it then press [Enter]. An icon appears
before the selected item to indicate which one it is. The settings are explained
in the following table:
(Continues on next page.)
Setting Function
SET USERNAME
AND
PASSWORD
This function is used to set usernames and passwords for the
administrator and users:
One administrator and four user passwords can be set.
After you select the administrator field or one of the user fields, a
screen that allows you to key in your username and password
appears. The username and password may be up to 15
characters long, and can consist of any combinat ion of letters
and numbers (A–Z, 0–9).
For each individual, key in the username and password, then
press [Enter].
To modify or delete a previous username or password, use the
backspace key to erase individual letters or numbers.
SET LOGOUT
TIMEOUT If there is no input from the console for the amount of time set with
this function, the operator is automatically logged out. A login is
necessary before the console can be used again.
This enables other operators to gain access to the computers when
the original operator is no longer accessing them, but has forgotten
to log out. To set the timeout value, key in a number from 1–180
minutes, then press [Enter]. If the number is 0 [zero], this function
is disabled. Default is 0 (disabled).
Chapter 4. OSD Operation
31
(Continued from previous page.)
(Continues on next page.)
Setting Function
EDIT PORT
NAMES To help remember which computer is attached to a particular port,
every port can be given a name. This function allows the
administrator to create, modify, or delete port names. To edit a port
name:
1. Click the port you want, or use the navigation keys to move the
highlight bar to it, then press [Enter].
2. Key in the new port name, or modify/delete the old one. The
maximum number of characters allowed for the port name is 12.
Legal characters include:
Alpha characters: A–Z
All numeric characters: 0–9
+ - / . and Space
Case does not matter; the OSD displays the port name in all
capitals no matter how they were keyed in.
3. When you have finished editing, press [Enter] to have the
change take effect. To abort the change, press [Esc].
RESTORE
DEFAULT
VALUES
This function is used to undo all changes and return the setup to
the original factory default settings (see OSD Factory Default
Settings, page 65) – except for the Names settings that were
assigned to the ports, which are saved.
CLEAR THE
NAME LIST This function clears the port name list.
ACTIVATE
BEEPER Choices are Y (for Yes), or N (for No). When activated, the beeper
sounds whenever a port is changed; when activating the Auto Scan
function (see F7 SCAN, page 35); or an invalid entry is made on an
OSD menu. The default is Y (activated).
CL1008 / CL1016 User Manual
32
(Continued from previous page.)
Setting Function
SET QUICK
VIEW PORTS This function lets the administrator select which ports to include as
quick view ports.
To select/deselect a port as a quick view port, use the navigation
keys to move the highlight bar to it, then press the [Spacebar].
When a port has been selected as a quick view port, an
arrowhead displays in the QV column of the list on the main
screen. When a port is deselected, the arrowhead disappears.
If one of the quick view options is chosen for the list view (see F2
LIST, page 27), only a port that has been selected here will
display on the list.
If one of the quick view options is chosen for auto scanning (see
SCAN/SKIP MODE, page 29), only a port that has been selected
here will be auto scanned.
The default is for no ports to be selected.
SET
ACCESSIBLE
PORTS
This function allows the administrator to define user access to the
computers on the installation on a port-by-port basis.
For each user, select the target port; then press the [Spacebar] to
cycle through the choices: F (Full access), V (View only), or blank.
Repeat until all access rights have been set, then press [Enter].
The default is F for all users on all ports.
Note: A blank setting means that no access right s are granted. The
port will not show up on the user's list on the main screen.
RESET ST A TION
IDS If you change the position of one of the stations in the daisy-chain,
the OSD settings will no longer correspond to the new situation.
This function directs the OSD to rescan the station positions of the
entire installation and updates the OSD so that the OSD station
information corresponds to the new physical layout.
Note: Only the station numbers get updated. Except for the port
names, all administrator settings (such as set accessible ports, set
quick view ports, etc.), for all of the computers affected by the
change, have to be manually redone.
FIRMWARE
UPGRADE In order to upgrade the CL1008 / CL1016's firmware (see
Chapter 6), you must first enable Firmware Upgrade Mode with this
setting.
When you bring up this menu, the current firmware version levels
display. Select Y to enable Firmware Upgrade mode, or N to leave
this menu without enabling it.
Chapter 4. OSD Operation
33
F5: SKP
This function enables you to easily skip backward or forward, switching the
KVM focus, from the currently active computer port to the previous or next
available one.
The selection of computers available for Skip mode switching is made
with the Scan/Skip mode setting under the F3 SET function
(see page 28).
When you are in Skip mode, press:
Note: When you skip ports, you only skip to the previous or next available
computer that is in the Scan/Skip mode selection (see page 29).
If a port has been selected for Scan/Skip mode, when the focus switches to
that port a left/right triangl e symbo l appears before its port ID display.
While Skip mode is in effect, the console will not function norm all y. You
must exit Skip mode in order to regain control of the console.
To exit Skip mode, press [Spacebar] or [Esc].
←To skip from the current port to the previous port in the list.
→To skip from the current port to the next port in the list.
↑To skip from the current port to the last port of the previous station in the
list.
↓To skip from the current port to the first port of the next station in the list.
CL1008 / CL1016 User Manual
34
F6: BRC
F6 is an administrator only function. When this function is in effect, commands
sent from the console are broadcast to all available computers on the
installation.
This function is particularly useful for operations that need to be performed on
multiple computers, such as performing a system wide shutdown, installing or
upgrading software, etc.
While BRC mode is in effect:
A speaker symbol appears before th e port ID display of the port that
currently has the console focus.
The mouse will not function normally. You must exit BRC mode in
order to regain control of the mouse.
To exit BRC mode, invoke the OSD (with the OSD hotkey), then press
[F6], to turn BRC mode off.
Chapter 4. OSD Operation
35
F7: SCAN
This function allows you to auto matically switch among the availabl e
computers at regular intervals so that you can monitor their activity without
having to take the trouble of switching yourself.
The selection of computers to be included for auto scanning is made with
the Scan/Skip mode setting under the F3 SET function (see page 28 ).
The amount of time that the focus stays on each port is set with the Scan
Duration setting under the F3 SET function (see page 28).
As each computer is accessed, an ‘S’ appears in front of the port ID
display to indicate that it is being accessed under Auto Scan mode.
While you are in Auto Scan mode, you can pause the scanning in order to
keep the focus on a particular computer either by pressing P, or with a left
click of the mouse. To resume scanning, press any key or left click, again.
See Invoking Auto Scan, page 39, for further details.
To exit Auto Scan mode and stay at a particular location, press
[Spacebar]. If the scanning stops on an empty port, or one where the
computer is attached but is powered off, the monitor screen will be blank
and the mouse and keyboard will have no effect. Simply wait – after the
Scan Duration ti me is up, the scan function wi ll m ove on to the next port.
While Auto Scan mode is in effect, the console will not function normally.
You must exit Auto Scan mode in order to regain control of the console.
To exit Auto Scan mode, press [Spacebar] or [Esc].
CL1008 / CL1016 User Manual
36
F8: LOUT
Clicking the F8 field, or pressing [F8] logs you out of the OSD, and blanks the
console screen. This is different from simply deactivat ing the OSD when you
are at the main screen by pressing [Esc].
With this function you must log in all over again to regain access to the OSD,
whereas with [Esc], all you have to do to reenter the OSD is tap the OSD
hotkey.
Note: 1. When you reenter the OSD after logging out, the screen stays blank
except for the OSD main screen. You must input your password
before you can continue.
2. If you reenter the OSD after logging out, and immediately use [Esc]
to deactivate the OSD without having selected a port from the OSD
menu, a null port message displays on the screen. The OSD hotkey
will bring up the main OSD screen.
37
Chapter 5
Hotkey Operation
Hotkey Port Access
Hotkey port access allows you to provide the KVM focus to a particular port
directly from the keyboard. The CL1008 / CL1016 provides three hotkey port
access features:
Selecting the Active Port
Auto Scanning
Skip Mode Switching
Note: The hotkey function must be enabled in the settings. See HOTKEY
COMMAND MODE, p. 29 for details.
Invoking Hotkey Mode
All hotkey operations begin by invoking Hotkey mode. There are two methods
that can be used to invoke Hotkey Mode. The first is to tap the Hotkey key on
the keyboard (see Dedicated Invocation Keys, page 66). The second is to use a
keyboard sequence.
To invoke Hotkey mode with the keyboard sequence, do the following:
1. Hold down the [Num Lock] key
2. Press and release the [Minus] key
3. Release the [Num Lock] key
Exiting Hotkey Mode
Press [Esc] to exit Hotkey mode.
CL1008 / CL1016 User Manual
38
Hotkey Mode Operation
Hotkey Mode Characteristics
When Hotkey Mode is active:
The Caps Lock, and Scroll Lock LEDs flash in succession to indicate so.
They stop flashing and revert to normal status when you exit Hotkey mode.
A Command Line appears on the monitor screen. The command line
prompt is the word Hotkey: in white text on a blue background, and
displays the subsequent hotkey information that you key in.
Ordinary keyboard and mouse functi ons are suspended – only hotkey
compliant keystrokes and mouse clicks (described in the sections that
follow), can be input. You must exit Hotkey mode (see p. 37) in order to
regain normal control of the console.
Selecting the Active Port
Each KVM port is assigned a unique Port ID (see Port ID Numbering,
page 21). You can directly access any computer on the installation with a
hotkey combinat ion that specifies the port ID of the KVM port that the
computer is connected to. The steps involved are:
1. Invoke Hotkey mode (see page 37).
2. Key in the port ID
The port ID numbers display on the command li ne as you key them in. If
you make a mistake, use [Backspace] to erase the wrong number.
3. Press [Enter]
After you press [Enter], the KVM focus switches to the designated
computer and you automatically exit Hotkey mode.
5. Hotkey Operation
39
Auto Scan Mode
Auto Scan automatically switches among all the active KVM ports that are
accessible to the currently logged in user at regular intervals, allowing
automatic monitoring of computer activity. (See Scan/Skip Mode of the OSD
F3: SET function, page 28 for information regarding accessible ports.)
Setting the Scan Interval
The amount of time Auto Scan dwells on each port is set with the Scan
Duration setting of the OSD F3 SET function (see page 28). You can change
the scan interval before activating hotkey auto scanning, if you wish, with the
followin g h ot key combination:
1. Invoke Hotkey mode (see page 37).
2. Key in [T] [n]
Where [T] is the letter T, and [n] is a number from 1–255 that rep resents
the number of seconds the system dwells on a port before going on to the
next.
The letter T and the numbers display on the command line as yo u key
them in. If you make a mistake, use [Backspace] to erase the wrong
number.
3. Press [Enter]
After you press [Enter], you automatically exit Hotkey mode, and are
ready to invoke auto scanning.
Invoking Auto Scan
To start auto scanning, key in the followi ng hotkey combination:
1. Invoke Hotkey mode (see page 37).
2. Press [A].
When you press A, you automatically exit Hotkey mode; enter Auto Scan
mode; and auto scanning begins.
While Auto Scan mode is in effect, ordinary keyboard and mouse functions are
suspended - only Auto Scan mode compliant keystrokes and mouse clicks can
be input. You must exit Auto Scan mode (see p. 40) in order to regain normal
control of the console.
CL1008 / CL1016 User Manual
40
Pausing Auto Scan
While you are in Auto Scan mode, you can pause the scanning in order to keep
the focus on a particular computer either by pressing P or with a left click of
the mouse. During the time that auto scanning is paused, the command line
displays: Auto Scan: Paused.
Pausing when you want to keep the focus on a particular comput er is more
convenient than exiting Auto Scan mode because when you resume scanning,
you start from where you left off.
If you exit Auto Scan mode, on the other hand, when you restart scanning, you
start over from the beginning with the very first computer on th e install ation.
To resume auto scanning after pausing, press any key or left click. Scanning
continues from where it left off.
Exiting AutoScan Mode
To exit Auto Scan mode press [Esc] or [Spacebar]. Auto scanning stops when
you exit Auto Scan mode.
5. Hotkey Operation
41
Skip Mode
This feature allows you to switch between computers in order to monitor th em
manually. You can dwell on a particular port for as long or as little as you like,
as opposed to auto scanning, which automatically switches after a fixed
interval. To invoke Skip Mode, key in the following hotkey combination:
1. Invoke Hotkey mode (see page 37).
2. Key in [Arrow]
Where [Arrow] refers to one of the arrow keys. After you press
[Arrow], you automatically exit Hotkey m ode, and enter Skip Mode
where you can switch ports as follows:
Once you are in Skip Mode, you can keep on skipping by pressing the
arrow keys. You don't have to invoke Hotkey mode again.
While Skip Mode is in effect, ordinary keyboard and mouse functions
are suspended – only Skip Mode compliant keystrokes can be input.
You must exit Skip Mode in order to regain normal control of the
console.
3. To exit Skip Mode, press [Esc] or [Spacebar].
←Skips from the current port to the first accessible port previous to it.
(See SCAN/SKIP MODE, p. 29, for information regarding accessible
ports.)
→Skips from the current port to the next accessible port.
↑Skips from the current port to the last accessible port of the previous
station. If you are at a port on the first st ation you cycle backward to the
last accessible port on the last station.
↓Skips from the current port to the first accessible port of the next
station. If you are at a port on the last station you cycle forward to the
first accessible port on the first station.
CL1008 / CL1016 User Manual
42
Hotkey Beeper Control
The beeper can be hotkey toggled on and off (see ACTIVATE BEEPER,
page 31). To toggle the beeper, key in the following hotkey combination:
1. Invoke Hotkey mode (see page 37).
2. Press [B]
After you press B, the beeper toggles on or off. The command line displays
Beeper On or Beeper Off for one second; then the message disappears and you
automatically exit Hotkey mode.
Hotkey Summary Table
[Num Lock] + [-] [Port ID] [Enter] Switches the KVM focus to the computer that
corresponds to that port ID
[T] [n] [Enter] Sets the Auto Scan interval to n seconds – where
n is a number from 1–255.
[A] Invokes Auto Scan mode.
When Auto Scan mode is in effect, [P] or left
click pauses auto scanning.
When auto scanning is paused, pressing P or
left clicking again resumes auto scanning.
Note: Pressing almost any of the typewr iter keys
(letters, numbers, Enter, Esc, Spacebar, etc.), will
resume scanning.
[←] Skips from the current port to the first accessible
port previous to it. (See SCAN/SKIP MODE, p. 29,
for information regarding accessible ports.)
[→] Skips from the current port to the next accessible
port.
[↑] Skips from the current port to the last accessible
port of the previous station. If you are at a port on
the first station you cycle backward to the last
accessible port on the last station.
[↓] Skips from the current port to the first accessible
port of the next station. If you are at a port on the
last station you cycle forward to the first accessible
port on the first station.
[B] Toggles the beeper on or off.
43
Chapter 6
The Firmware Upgrade Utility
The Windows-based Firmware Upgrade Utility (FWUpgrade.exe) provides a
smooth, automated process for upgrading the KVM switch's firmware.
The utility comes as part of a Firmware Upgrade Package that is specific for
each device. New firmware upgrade packages are posted on our web site as
new firmware revisions become available. Check the web site regularly to find
the latest packages and information relating to them.
Preparation
To prepare for the firmware upgrade, do the follo wing:
1. From a computer that is not part of your KVM installation go to our
Internet support site and choose the model name that relates to your device
to get a list of available firmware upgrade packages.
2. Choose the firmware upgrade package you want to install (usually the
most recent), and download it to your computer.
3. Use the Firmware Upgrade Cable (pro vided with this unit), to connect a
COM port on your computer to the Firmware Upgrade Port of the switch.
CL1008 / CL1016 User Manual
44
4. Shut down all of the computers, but not the stations, on your KVM
installation.
5. From your KVM switch console, brin g up the OSD (see p. 23) and select
the F4 ADM function.
6. Scroll down to FIRMWARE UPGRADE. Press [Enter], then press [Y] to
invoke Firmware Upgrade mode (see p. 32) For your reference, the
current firmware upgrade version displays on the screen.
Note: On a dais y chained installation, the chained stations will automatically
receive the upgrade via the daisy chain cables.
6. The Firmware Upgrade Utility
45
Starting the Upgrade
To upgrade your firmware:
1. Run the downloaded firmware upgrade package file, either by double
clicking the file icon, or by opening a command line and entering the full
path to it.
The firmware upgrade utility Welcome screen appears:
Note: The screens shown in this section are for reference only. The
wording and layout of the actual screens put up by the firmware
upgrade utility may vary sligh tly from these examples.
2. Read and Agree to the license agreement (enable the I Agree radio button).
3. Click Next to continue.
CL1008 / CL1016 User Manual
46
The firmware upgrade utility main screen appears:
The utility inspects your installation. The devices capab le of bein g
upgraded are listed in the Device List panel.
4. After all the devices have been listed, click Next to perform the upgrade.
If you enabled Check Firmware Version, the utility compares the
device's firmware level with that of the upgrade files. If it finds that the
device's version is higher than the upgrade version, it brings up a
dialog box informing you of the situation and gives you the option to
continue or cancel.
If you didn't enable Check Firmware Version, the utility installs the
upgrade files without checking whether they are a higher level, or not.
6. The Firmware Upgrade Utility
47
As the upgrade proceeds status messages appear in the Status
Messages panel, and the progress toward completion is shown on th e
Progress bar.
To abort the upgrade procedure before it completes, click Cancel.
If you cancel before completion, a dialog box appears warning you that
quitting at this point may cause the device’s firmware to be lost, and
you are given the option to proceed or abort the cancel operation.
To recover from a “lost firmware” situation, see Firmware Upgrade
Recovery, page 48.
Upgrade Succeeded
After the upgrade has completed, a screen appears to inform you that the
procedure was successful:
Click Finish to close the firmware upgrade utility.
Upgrade Failed
If the Upgrade Succeeded screen doesn't appear, it means that the upgrade
failed to complete successfully. See the next section, Firmware Upgrade
Recovery, for how to proceed.
CL1008 / CL1016 User Manual
48
Firmware Upgrade Recovery
There are basically three conditions that call for firmware upgrade recovery:
When you invoke Firmware Upgrade mode (see Preparation, page 43),
but decide not to proceed with the upgrade.
When the mainboard firmware upgrade fails.
When the I/O firmware upgrade fails.
To perform a firmware upgrade recovery, do the following:
1. Power off the switch. If it is part of a daisy chain, disconnect it from the
chain.
2. Connect the Firmware Upgrade Cable to its Firmware Upgrade Port.
3. Slide the Firmware Upgrade Recovery Switch to the Recover position.
4. Power the switch back on and repeat the upgrade procedure.
5. After the switch has been successfully upgraded, power it off, and slide the
Firmware Upgrade Recovery Switch back to the Normal position.
6. If the switch is part of a daisy chain, replace it in the chain.
7. Power the switch back on.
49
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
To prevent damage to your installation it is importan t that all devices are
properly grounded.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage wi ll resul t.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be bl ocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been
provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device shoul d be oper ated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V
phase-to-phase voltage.
The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug . Always follow your local/national
wiring codes.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
CL1008 / CL1016 User Manual
50
To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yoursel f. Refer all servicin g to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
Do not connect the RJ-11 conn ector mark ed “UPGRADE” to a public
telecommunication network.
Appendix
51
Rack Mounting
Before working on the rack, ma ke sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflow is provided to devices in the rack.
Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer
Do not step on or stand on any device when servicing other devices in a
rack.
Caution: Slide/rail (LCD KVM) mounted
equipment is not to be used as a shelf or a work
space.
CL1008 / CL1016 User Manual
52
Consignes de sécurité
Général
Ce produit est destiné exclusivement à une utilisatio n à l’intérieur.
Veuillez lire la totalité de ces instructions. Conservez-les afin de pouvoir
vous y référer ultérieurement.
Respectez l’ensemble des avertissements et instructions inscrits sur
l’appareil.
Ne placez jamais l’unité sur une surface instable (chariot, pied, table, etc.).
Si l’unité venait à tomber, elle serait gravement endommagée.
N’utilisez pas l’unité à proximité de l’eau.
Ne placez pas l’unité à proximité de ou sur des radiateurs ou bouches de
chaleur.
Le boîtier de l’unité est doté de fentes et d’ouvertures destinées à assurer
une ventilation adéquate. Pour garantir un fonctio nnem e nt fi able et
protéger l’unité contre les surchauffes, ces ouvertures ne doivent jamais
être bloquées ou couvertes.
L’unité ne doit jamais être placée sur une surface molle (lit, canapé, tapis,
etc.) car ses ouvertures de ventilation se trouveraient bloquées. De même,
l’unité ne doit pas être placée dans un meuble fermé à moins qu'une
ventilation adaptée ne soit assurée.
Ne renversez jamais de liquides de quelque sorte que ce soit sur l’unité.
Débranchez l’unité de la prise murale avant de la nettoyer. N’utilisez pas
de produits de nettoyage liquide ou sous form e d’aérosol. Util isez un
chiffon humide pour le nettoyage de l’unité.
L’appareil doit être alimenté par le typ e de source indiqué sur l’étiq uett e.
Si vous n’êtes pas sûr du type d’alimentation disponible, consultez votre
revendeu r ou le fo urnisseur local d’électricité.
Afin de ne pas endommager votre installation, vérifiez que tous les
périphériques sont correctemen t mis à la terre.
L’unité est équipée d’une fiche de terre à trois fils. Il s’agit d’une fonction
de sécurité. Si vous ne parvenez pas à insérer la fiche dans la prise murale,
contactez votre électricité afin qu’il remplace cette dernière qui doit être
obsolète. N’essayez pas d’aller à l’encontre de l’objectif de la fiche de
terre. Respectez toujours les codes de câblage en vigueur dans votre
région/pays.
Appendix
53
L’équipement doit être installé à pro xim ité de la prise murale et le
dispositif de déconnexio n (prise de courant femelle) doit être facile
d’accès.
La prise murale doit être installée à proximité de l’équipeme nt et doit être
facile d’accès.
Veillez à ce que rien ne repose sur le cordon d’alimentation ou les câbles.
Acheminez le cordon d’alimentation et les câbles de sorte que personne ne
puisse marcher ou trébucher dessus.
En cas d’utilisation d’une rallonge avec cette unité, assurez-vous que le
total des ampérages de tous les produits utilisés sur cette rallonge ne
dépasse pas l’ampérage nominal de cette dernière. Assurez-vous que le
total des ampérages de tous les produits branchés sur la prise murale ne
dépasse pas 15 ampères.
Pour contribuer à protéger votre système contre les augmentations et
diminutions soudaines et transitoires de puissance électrique, utilisez un
parasurtenseur, un filtre de ligne ou un système d’alim ent a tion sans
coupure (UPS).
Placez les câbles du système et les câbles d’alimentation avec précaution ;
veillez à ce que rien ne repose sur aucun des câbles.
Lors du branchement ou du débranchement à des blocs d’alimentation
permettant la connexion à chaud, veuillez respecter les lignes direct rices
suivantes:
Installez le bloc d’alimentation avant de brancher le câble d’alimentation à
celui-ci.
Débranchez le câble d’alimentation avant de retirer le bloc d'alimentation.
Si le système présente plusieurs sources d’alimentation, déconnectez le
système de l'alimentation en débranchant tous les câbles d'alimentation des
blocs d'alimentation.
N’insérez jamais d’objets de quelque sorte que ce soit dans ou à travers les
fentes du boîtier . Ils pourraient entrer en contact avec des points de tension
dangereuse ou court-circuiter des pièces, entraînant ainsi un risque
d’incendie ou de choc électrique.
N’essayez pas de réparer l’unité vous-même. Confiez toute opération de
réparation à du personnel qualifié.
Si les conditions suivantes se produisent, débranchez l’unité de la prise
murale et amenez-la à un technicien qualifié pour la faire réparer:
Le cordon d’alimentat ion ou la fiche ont été endommagés ou éraillés.
Du liquide a été renversé dans l’unité.
CL1008 / CL1016 User Manual
54
L’unité a été exposée à la pluie ou à l’eau.
L’unité est tombée ou le boîtier a été endommagé.
Les performances de l’unité sont visiblement altérées, ce qui indique la
nécessité d’une réparation.
L’unité ne fonctionne pas normalement bien que les instructions
d’utilisation soient respectées.
N’utilisez que les commandes qui sont abordées dans le mode d’emploi.
Le réglage incorrect d’autres commandes peut être à l’origine de
dommages qui nécessiteront beaucoup de travail pour qu’un technicien
qualifié puisse réparer l’unité.
Ne connectez pas le connecteur RJ-11 portant la marque « Sensor »
(Capteur) à un réseau de télécommunication public.
Appendix
55
Montage sur bâti
Avant de travailler sur le bâti, assurez-vous que les stabilisateurs sont bien
fixées sur le bâti, qu’ils sont étendus au sol et que tout le poids du bâti
repose sur le sol. Installez les stabilisateurs avant et latéraux sur un même
bâti ou bien les stabilisateurs avant si plusieurs bâtis sont réunis, avant de
travailler sur le bâti.
Chargez toujours le bâti de bas en haut et chargez l’élément le plus lourd
en premier.
Assurez-vous que le bâti est à niveau et qu’il est stable avant de sortir une
unité du bâti.
Agissez avec précaution lorsque vous appuyez sur les loquets de libération
du rail d’unité et lorsque vous faites coulisser une unité dans et hors d’un
bâti ; vous pourriez vous pincer les doigts dans les rails.
Une fois qu’une unité a été insérée dans le bâti, étendez avec précaution le
rail dans une position de verrouillage puis faites glisser l’unité dans le bâti.
Ne surchargez pas le circuit de l’alimentation CA qui alimente le bâti . La
charge totale du bâti ne doit pas dépasser 80 % de la capacité du circuit.
Assurez-vous que tous les équipements utilisés sur le bâti, y-compris les
multiprises et autres connecteurs électriques, sont correctement mis à la
terre.
Assurez-vous que les unités présentes dans le bâti bénéficie d’une
circulation d’air suffisante.
Assurez-vous que la température ambiante de fonctionnement de
l’environnement du bâti ne dépasse pas la température ambiante maximale
spécifiée pour l’équipement par le fabricant.
Ne marchez sur aucun appareil lors de la maintenance d’autres appareils
d’un bâti.
Attention: Glisser / rail (LCD KVM) monté
l'équipement ne doit pas être utilisé comme une
étagère ou un espace de travail.
CL1008 / CL1016 User Manual
56
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://eservice.aten.com
For telephone support, see Telephone Support, page iv
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration, including operatin g system, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
Appendix
57
Specifications
CL1008
Function CL1008
Computer
Connections Direct 8
Max 128 (via Daisy Chain)
Port Selection OSD; Hotkey; Pushbutton Switches
Connectors KVM Ports 8 x SPHD-15 Female (Yellow)
Daisy Chain 1 x DB-25 Male (Black)
FW Upgrade 1 x RJ-11 Female
Power 1 x 3-prong AC socket
Switches Reset 1 x Semi-recessed pushbutton
Power 1 x Rocker
F/W Upgrade. 1 x Slide
LCD Adjust 4 x Pushbutt on
Port Selection 8 x Pushbutt on
LEDs On Line 8 (Orange)
Selected 8 (Green)
Power 1 (Dark Green)
Lock Num 1 (Green)
Caps 1 (Green)
Scroll 1 (Green)
Emulation Keyboard / Mouse PS/2
Video 1280 x 1024 @ 75 Hz; DDC2B
Scan Interval (OSD Select) 1–255 secs.
I/P Rating 100–240V AC; 50/60Hz; 1A
Power Consumption 120V, 15W; 230V, 17W
Environment Operating Temp. 0–40o C
St orag e Temp. -20–60o C
Humidity 0–80% RH non-condensing
Physical
Properties Housing Metal + Plastic
Weight 13.34 kg
Dimensions (L x W x H) 48.00 x 64.02 x 4.40 cm (17”/1U)
CL1008 / CL1016 User Manual
58
CL1016
Function CL1016
Computer
Connections Direct 16
Max 256 (via Daisy Chain)
Port Selection OSD; Hotkey; Pushbutton Switches
Connectors KVM Ports 16 x SPHD-15 Female (Yellow)
Daisy Chain 1 x DB-25 Male (Black)
FW Upgrade 1 x RJ-11 Female
Power 1 x 3-prong AC socket
Switches Reset 1 x Semi-recessed pushb utt on
Power 1 x Rocker
F/W Upgrade. 1 x Slide
LCD Adjust 4 x Pushbutton
Port Selection 16 x Pushbutton
LEDs On Line 16 (Orange)
Selected 16 (Green)
Power 1 (Dark Green)
Lock Num 1 (Green)
Caps 1 (Green)
Scroll 1 (Green)
Emulation Keyboard / Mouse PS/2
Video 1280 x 1024 @ 75 Hz; DDC2B
Scan Interval (OSD Select) 1–255 secs.
I/P Rating 100–240V AC; 50/60Hz; 1A
Power Consumption 120V, 18W; 230V, 20W
Environment Operating Temp. 0–40o C
Storage Temp. -20–60o C
Humidity 0–80% RH Non-condensing
Physical
Properties Housing Metal + Plastic
Weight 13.55 kg
Dimensions (L x W x H) 48.00 x 64.02 x 4.40 cm (17”/1U)
Appendix
59
Connection Tables
The following tables indicate the relationship between the number of units and
the number of computers that they control on a daisy chained installation:
CL1008 – ACS1208A
CL1008 – ACS1216A
No. Computers No. Computers
1 1–8 9 65–72
2 9–16 10 73–80
3 17–24 11 81–88
4 25–32 12 89–96
5 33–40 13 97–104
6 41–48 14 105–112
7 49–56 15 113–120
8 57–64 16 121–128
No. Computers No. Computers
1 1–8 9 121–136
2 9–24 10 137–152
3 25–40 11 152–168
4 41–56 12 169–184
5 57–72 13 185–200
6 73–88 14 201–216
7 89–104 15 217–232
8 105–120 16 233–248
CL1008 / CL1016 User Manual
60
CL1016 – ACS1208A
CL1016 – ACS1216A
No. Computers No. Computers
1 1–16 9 73–80
2 17–24 10 81–88
3 25–32 11 89–96
4 33–40 12 97–104
5 41–48 13 105–112
6 49–56 14 113–120
7 57–64 15 121–128
8 65–72 16 129–136
No. Computers No. Computers
1 1–16 9 129–144
2 17–32 10 145–160
3 33–48 11 161–176
4 49–64 12 177–192
5 65–80 13 193–208
6 81–96 14 209–224
7 97–112 15 225–240
8 113–128 16 241–256
Appendix
61
Clear Login Information
If you are unable to perform an Administrator login (because the username and
password information has become corrupted, or you have forgotten it, for
example), you can clear the login information with the following procedure:
1. Power off the switch and remove the top cover from the unit chassis.
2. Short the jumper labeled Default Password on the switch's main board
.
3. Power on the switch.
When you power the switch on, the following message appears on the
LCD display:
USERNAME AND PASSWORD INFORMATION HAS BEEN CLEARED.
PLEASE POWER OFF THE SWITCH, REMOVE THE JUMPER, CLOSE
THE CASE, THEN RESTART.
4. After you start back up, the OSD login function acts exactly the way it did
the first time the switch was run (see OSD Overview, page 23) and you can
reset passwords for the administrators and users.
J17
CL1008 / CL1016 User Manual
62
Optional Rack Mounting
For convenience and flexibility, three option a l rack m ounting kits are
available:
A long bracket standard rack mounting kit for 68.0–1 05.0 cm racks;
A short bracket Easy-Installation rack moun t kit for 52.0–70.0 cm racks;
A long bracket Easy-Instal lati on rack mount kit for 68.0–105.0 cm racks.
Standard - Long
To install the long bracket standard rack mount kit, simply replace the short L
brackets on the standard rack mount kit with the long ones, and mount the
switch according to the instructions given for Standard Rack Mounting, page 9.
Easy Installation
With an Easy-Installation, kit, one person can mount the switch. To install the
Easy-Installation kit, do th e followi ng:
1. Remove the standard L brackets, and the side mounting brackets from both
sides of the switch.
2. Attach the lef t and ri gh t easy-installation mounting rails to the inside of
the rack. The flange that supports the switch will be to the inside.
Appendix
63
a) Screw the front flanges to the rack first.
b) Slide the bars with the rear flanges toward th e rack until the flanges
make contact with the rack, then screw the rear flanges to the rack.
Support
Flange
Rear Flange
Slide Bar
Rear Attachment
Sliding Bracket
Rear Flange
LEFT
RAIL
RIGHT
RAIL
CL1008 / CL1016 User Manual
64
3. Slide the switch onto the support flanges. Use the screws supplied with
this package to loosely attach the front of the switch to the front of the rack
(only tighten the screws part way).
4. Slide the rear attachment sliding brackets along the slide bars until they
contact the rear of the switch, then use the screws supplied with this
package to attach the bars to the rear of the switch (tighten the screws all
the way).
Phillips I head
M4 x 6
Phillips I head
M4 x 6
Appendix
65
5. Slide the switch open and closed a couple of times to be sure that it is
properly aligned and operating smoothly. (See page 15 for opening and
closing procedures.)
6. After determining that the switch is properly lined up and op erating
correctly, finish up by fully tightening down the partiall y tigh tened front
attachment screws inserted in step 3.
OSD Factory Default Settings
The factory default settings are as follows:
Setting Default
OSD Hotkey [Scroll Lock] [Scroll Lock]
Port ID Display Position Upper Left Corner
Port ID Display Duration 3 Seconds
Port ID Display Mode The Port Number plus the Port Name
Scan Duration 5 Seconds
Scan/Skip Mode All
Screen Blanker 0 (Disabled)
Logout Timeout 0 (Disabled)
Beeper Y (Activated)
Accessible Ports F (Full) For all Users on all Ports
CL1008 / CL1016 User Manual
66
Dedicated Invocation Keys
Two dedicated keys are provided on the keyboard module to make it eas y to
invoke Hotkey Mode and the OSD, as shown in the diagram, below
:
Note: These keys are toggles . Press once to invoke the feature, press again to
exit.
About SPHD Connectors
This product uses SPHD connectors for its KVM and/or
Console ports. We have specifically modified the shape of these
connectors so that only KVM cables that we have designed to
work with this product can be connected.
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILI TY EXCE ED THE PRICE PAID
FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESUL TING FRO M THE USE OF THE PRODUCT, DISK,
OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with
respect to the contents or use of this documentation, and especially disclaims its quality,
performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or
documentation without obligation to notify any indivi dual or entity of such
revisions, or update. For further inquiries, please contact your direct vendor.
67
Index
A
Activate Beeper, 31
Active port
selecting, 38
ADM, 30
Administrator functions, 30
Auto Scan Mode, 39
Auto Scanning, 35
Invoking Auto Scan, 39
Pausing Auto Scan, 40
Scan Duration, 29
Setting the Scan Interval, 39
Stopping, 40
B
Beeper
Activate, 31
Hotkey Control, 42
BRC, 34
Broadcast Mode, 34
C
CL1008 / CL1016
Overview, 1
Clear Login Information, 61
Clear the Nam e Li st, 31
Closing the console, 16
Components, 4
front view, 4
rear view, 7
Connection Tables, 59, 60
Console
Closing, 16
Opening, 15
D
Daisy chaining, 13
Dedicated Invocation Keys, 66
E
Easy installation rack moun ting, 62
Edit Port Names, 31
F
F1 GOTO, 26
F2 LIST, 27
F3 SET, 28
F4 ADM, 30
F5 SKP, 33
F6 BRC, 34
F7 SCAN, 35
F8 LOUT, 36
Factory Default Settings, 65
Features, 2
Firmware upgrade
firmware upgrade port, 43
preparation, 43
recovery, 48
Front View, 4
G
GOTO, 26
H
HKM, 37
Hot Plugging, 22
Hotkey
Auto scanning, 39
Beeper Control, 42
Command Mode, 29
Invoking Hotkey Mode, 37
OSD, 28
Port access, 37
Selecting the Active Port, 38
Skip mode, 41
Summary Table, 42
Hotkey Mode
CL1008 / CL1016 User Manual
68
exiting, 37
I
Installation
Daisy chaining, 13
Single Stage, 11
Invocation Keys, 66
Invoking Hotkey Mode, 37
L
LCD
Adjustment Settings, 20
OSD configuration, 19
LIST, 27
Logout, 36
Logout Timeout, 30
LOUT, 36
M
Manual port switching, 21
O
Online
Registration, iv
Opening the Console, 15
Operating Precautions, 17
Optional rack mounting, 62
OSD
Factory Default Settings, 6 5
Functions, 26
Hotkey, 28
Logout, 36
Main Screen, 24
Main Screen Headings, 25
Navigation, 25
Overview, 23
P
Password, 30
Pause, 35
Port ID
Display Duration, 28
Display Mode, 29
Display Position, 28
Numbering, 21
Port Names, 31
Port selection, 21
active port, 38
Powering Off and Restarting, 18
Powering Up, 18
Q
Quick View Ports, 32
R
Rack mounting
Easy installation, 62
Optional, 62
Safety information, 51
Standard, 9
Rear View, 7
Requirements
Cables, 3
Computers, 3
OS Support, 4
Reset Station IDs, 32
Restore Default Values, 31
RoHS, ii
S
Safety Instructions
General, 49
rack mounting, 51
SCAN, 35
Scan Duration, 29
SCAN/SKIPMODE, 29
Screen Blanker, 29
Selecting the Active Port, 38
SET, 28
Accessible Ports, 32
Logout Time out, 30
