Table of Contents
- Compliance Statements
- About this Manual
- Package Contents
- Product Information
- User Information
- Contents
- Chapter 1 Introduction
- Chapter 2 Hardware Setup
- Chapter 3 Basic Operation
- Chapter 4 Hotkey Operation
- Port Switching
- Auto Scanning
- Hotkey Setting Mode
- Invoking HSM
- Alternate HSM Invocation Keys
- Alternate Port Switching Keys
- Keyboard Operating Platform
- List Switch Settings
- USB Reset
- Keyboard Language
- Hotkey Buzzer Control
- Port Switching Keys
- Firmware Upgrade Mode
- Restore Default Settings
- Video DynaSync
- Alternative Manual Port Selection Settings
- Mouse Emulation Control
- Mouse Port-switching
- Keyboard Emulation Control
- SPC Mode
- Power on Detection
- HSM Summary Table
- Chapter 5 Keyboard Emulation
- Chapter 6 The Firmware Upgrade Utility
- Appendix
ATEN CS1784A-RT User Manual
Displayed below is the user manual for CS1784A-RT by ATEN which is a product in the KVM Switches category. This manual has pages.
Related Manuals
CS1782A / CS1784A
USB DVI Dual Link KVMP™ Switch
User Manual
cs1782a-1784a.book Page i Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
ii
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
KCC Statement
cs1782a-1784a.book Page ii Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
iii
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
RoHS
This product is RoHS compliant.
cs1782a-1784a.book Page iii Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
iv
About this Manual
This User Manual is provided to help you get the most from your CS1782
A
/
CS1784
A
. It covers all aspects of installation, configuration and operation. An
overview of the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the CS1782
A
/ CS1784
A
system. Its purpose, features and benefits are presented, and its front and back
panel components are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary steps are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the CS1782
A
/ CS1784
A
.
Chapter 4, Hotkey Operation, details all of the concepts and procedures
involved in the Hotkey operation of your CS1782
A
/ CS1784
A
installation.
Chapter 5, Keyboard Emulation, provides tables that list the PC to Mac
and PC to Sun keyboard emulation mappings.
Chapter 6, The Firmware Upgrade Utility, explains how to upgrade the
CS1782
A
/ CS1784
A
's firmware with the latest available versions.
Appendix, provides specifications and other technical information regarding
the CS1782
A
/ CS1784
A
.
cs1782a-1784a.book Page iv Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
v
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential
steps.
>Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
>
Run means to
open the Start menu, and then select Run.
Indicates critical information.
cs1782a-1784a.book Page v Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
vi
Package Contents
The CS1782
A
/ CS1784
A
package consists of:
1 CS1782
A
/ CS1784
A
USB DVI Dual Link KVMP
TM
Switch
2 custom DVI-D KVM cable sets (CS1782
A
only)
4 custom DVI-D KVM cable sets (CS1784
A
only)
2 custom 7.1 channel surround sound cable sets (CS1782
A
only)
1 power adapter
1 user instructions*
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
*Features may have been added to the device since this manual was printed.
Please visit our website to download the most up-to-date version of the
manual.
cs1782a-1784a.book Page vi Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
vii
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
International http://www.aten.com
North America http://www.aten-usa.com
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
cs1782a-1784a.book Page vii Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
viii
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
cs1782a-1784a.book Page viii Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
ix
Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Chapter 1.
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
CS1782A Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
CS1784A Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
CS1782A Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
CS1784A Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Chapter 2.
Hardware Setup
Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CS1782A 7.1 Channel Surround Sound Installation . . . . . . . . . . . 14
Chapter 3.
Basic Operation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Manual Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Mouse Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Alternative Manual Port Selection Settings . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 4.
Hotkey Operation
Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
cs1782a-1784a.book Page ix Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
x
Cycling Through the Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Going Directly to a Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auto Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Hotkey Setting Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Invoking HSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Alternate HSM Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Alternate Port Switching Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Keyboard Operating Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
List Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
USB Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Keyboard Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Hotkey Buzzer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Port Switching Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Firmware Upgrade Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Restore Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Video DynaSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Alternative Manual Port Selection Settings . . . . . . . . . . . . . . . . . . . . . 29
Mouse Emulation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Mouse Port-switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Keyboard Emulation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SPC Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power on Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
HSM Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 5.
Keyboard Emulation
Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Sun Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Chapter 6.
The Firmware Upgrade Utility
Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Appendix
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Hotkey Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
cs1782a-1784a.book Page x Monday, July 19, 2021 4:50 PM
1
Chapter 1
Introduction
Overview
The CS1782
A
/ CS1784
A
USB DVI Dual Link KVMP
TM
Switch charts a
revolutionary new direction in KVM (Keyboard, Video, Mouse) switch
functionality by combining a 2/4 port KVM switch with a 2 port USB hub at
the same time as providing an interface for a Digital Visual Interface (DVI)
monitor. In addition, the CS1782
A
/ CS1784
A
comes with ATEN’s new Video
DynaSync
TM
technology, which eliminates boot-up display problems and
optimizes resolution, and power on detection, which means if one computer is
powered off, the CS1782
A
/ CS1784
A
will automatically switch to the next
powered-on computer. Further innovations include the latest in mouse port-
switching – simply double-click on the scroll wheel of a USB mouse to change
ports – and gaming keyboard support, making the CS1782
A
/ CS1784
A
the new
standard for desktop KVM switches.
As a KVM switch, the CS1782
A
/ CS1784
A
allows users to access two or four
computers from a single USB keyboard, USB mouse, and monitor console. As
a USB 2.0 hub, it permits each computer to access any peripherals connected
to the hub on a one-computer-at-a-time basis.
The unit’s independent switching feature, allows the KVM focus to be on one
computer wh ile the USB peripheral focus is o n a nother. This eliminate the need
to purchase a separate USB hub as well as the need to purchase separate stand-
alone peripheral sharers.
The CS1782
A
/ CS1784
A
further improves on previous designs with DVI
connectors, and the transfer of keyboard and mouse data to the computers via
a fast, reliable USB connection. DVI supports both digital video input (flat
panel displays, data projectors, plasma displays, digital TVs and set-top boxes)
and analog video input (traditional monitors and TVs). The CS1782
A
/
CS1784
A
also breaks into the computer gaming environment as it supports
gaming keyboard functions. It allows users to enjoy and control their game
applications with familiar keyboard inputs without having to change to a
compatible keyboard.
The CS1782
A
/ CS1784
A
is audio enabled, with the CS1782
A
supporting 7.1
channel surround sound audio and the CS1784
A
supporting 2.1 channel
surround sound audio. You can listen to the audio output of each computer on
cs1782a-1784a.book Page 1 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
2
two sets of speakers on a one-computer-at-a-time basis. As with the USB
peripherals, the audio focus can be independent of the KVM focus.
Setup is fast and easy; simply plug cables into their appropriate ports. There is
no software to configure, no installation routines, and no incompatibility
problems. Since the CS1782
A
/ CS1784
A
intercepts keyboard input directly, it
will work on multiple computing platforms (PC (x86/x64), Macintosh
PowerPC, and Sun Microsystems Sparc).
There are three convenient methods to access the computers: port selection
pushbuttons located on the unit’s front panel; hotkey combinations entered
from the keyboard; and via mouse – simply double-click on the scroll wheel of
a USB mouse to change ports.
There is no better way to save time and money than with a CS1782
A
/ CS1784
A
installation. Since a single console manages all of the computers, the CS1782
A
/ CS1784
A
setup: eliminates the expense of having to purchase separate
console components for each computer; saves all the space those extra
components would take up; saves on energy costs; and eliminates the
inconvenience and wasted effort involved in constantly moving from one
computer to another.
cs1782a-1784a.book Page 2 Monday, July 19, 2021 4:50 PM
Chapter 1. Introduction
3
Features
2-port DVI KVMP Switch with USB 2.0 and 7.1 Surround Sound Audio
(CS1782
A
)
4-port DVI KVMP Switch with USB 2.0 and 2.1 Surround Sound Audio
(CS1784
A
)
One USB console controls two/four computers and two additional USB
devices
2-port USB 2.0 hub built in; fully compliant with the USB 2.0
specification
Full bass response provides a rich experience for 7.1 channel surround
sound systems (CS1782
A
)
Full bass response provides a rich experience for 2.1 channel surround
sound systems (CS1784
A
)
Computer selection via front panel pushbuttons, hotkeys, and mouse
Multiplatform support – Windows 2000/XP/Vista/7, Linux, Mac, and
Sun*
Independent switching of KVM, USB hub, and Audio focus
DVI digital and analog monitor support – fully compliant with the DVI-I
specifications (custom DVI-I cable needed for analog output support)
Superior video quality:
1920 x 1200 @ 60Hz (Single Link)
2560 x 1600 @ 60Hz (Dual Link)
Supports widescreen resolutions
Video DynaSync
TM
– Exclusive ATEN technology eliminates boot-up
display problems and optimizes resolution when switching between ports
Power on detection – if one of the computers is powered off, the switch
will automatically switch to the next powered-on computer
Console mouse port emulation/bypass feature supports most mouse
drivers and multifunction mice
Console keyboard port emulation/bypass feature supports most gaming /
multimedia keyboards
Complete keyboard emulation for error-free booting
Mac/Sun keyboard support and emulation*
cs1782a-1784a.book Page 3 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
4
Multilingual keyboard mapping – supports English, Japanese, and French
keyboards
Auto Scan Mode for monitoring all computers
Firmware upgradable
Note: 1. PC keyboard combinations emulate Mac / Sun keyboards
2. Mac / Sun keyboard work only with their own computers
cs1782a-1784a.book Page 4 Monday, July 19, 2021 4:50 PM
Chapter 1. Introduction
5
Hardware Requirements
Console
A DVI compatible monitor capable of the highest possible resolution
A USB mouse
A USB keyboard
Microphone and speakers (optional)
Computers
The following equipment must be available on each computer:
A DVI port
Note: The video quality of the display is affected by the performance of
the graphics card. For best results, we recommend you upgrade to a
more powerful discrete graphics card.
A USB Type-A port
(Optional) Audio ports
Cables
Only DVI-D KVM cable sets, wh ich are specific ally designed to work with this
switch, may be used to link to the computers. Two (CS1782
A
) or four
(CS1784
A
) cable sets are provided with this package.
Note: The video quality of the display is affected by the quality and length of
the cables. If you need additional cable sets, please contact your dealer
to purchase the appropriate ones for your switch.
Type Length Part Number
USB DVI-D Dual Link
Cables
1.8 m 2L-7D02UD
3.0 m 2L-7D03UD
5.0 m 2L-7D05UD
cs1782a-1784a.book Page 5 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
6
Operating Systems
Supported operating systems are shown in the table, below:
Note: 1. Supports Linux Kernel 2.6 and higher.
2. The CS1782
A
/ CS1784
A
has a built-in USB 2.0 hub, so does not
support PCs or OS that do not support USB 2.0.
OS Version
Windows 2000 / XP / 2003 / 2008 / Vista / 7
Linux RedHat 9.0 and higher
SuSE 10 / 11.1 and higher
Debian 3.1 / 4.0
Ubuntu 7.04 / 7.10
UNIX AIX 4.3 and higher
FreeBSD 5.5 and higher
Sun Solaris 8 and higher
Novell Netware 6.0 and higher
Mac OS 9 to 10.6 (Snow Leopard)
cs1782a-1784a.book Page 6 Monday, July 19, 2021 4:50 PM
Chapter 1. Introduction
7
Components
CS1782
A
Front View
CS1784
A
Front View
cs1782a-1784a.book Page 7 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
8
No. Component Description
1 port
selection
pushbuttons
For manual port selection (see Overview, page 15, also):
Press a port selection pushbutton for less than two seconds to
bring the KVM, USB hub, and audio focus to the computer
attached to its corresponding port.
Press a port selection pushbutton twice to bring the audio focus to
the computer attached to its corresponding port.
Press a port selection pushbutton for longer than two seconds to
bring only the KVM focus to the computer attached to its corre-
sponding port.
Press switches 1 and 2 simultaneously for 2 seconds to start Auto
Scan Mode, see Auto Scanning, page 24 for details.
2 port LEDs The port LEDs are built into the port selection switches. The
upper ones are the KVM port LEDs; the lower ones are the
USB LEDs:
KVM
Lights DIM ORANGE to indicate that the computer attached to the
corresponding port is up and running (On Line).
Flashes to indicate that firmware upgrade mode is in effect.
Lights BRIGHT ORANGE to indicate that the computer attached to
the corresponding port is the KVM focus (Selected).
Flashes to indicate that the computer attached to the correspond-
ing port is being accessed under auto scan mode.
USB
Lights GREEN to indicate that the computer attached to its corre-
sponding port is the one that has access to the USB peripherals.
3 audio ports The cables from your main speakers and main microphone
plug in here. The speakers and microphone plugged in here
have priority over those in the rear panel.
4 USB 2.0
hub
USB 2.0 peripherals (printers, scanners, etc.) can plug into
this port (this may require an extra power adapter).
cs1782a-1784a.book Page 8 Monday, July 19, 2021 4:50 PM
Chapter 1. Introduction
9
CS1782
A
Rear View
CS1784
A
Rear View
cs1782a-1784a.book Page 9 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
10
No. Component Description
1 console port
section
The cables from your DVI monitor, USB keyboard, USB
mouse, speakers, and microphone plug in here. Each
connector is marked with an appropriate icon to indicate
itself.
2 KVM port
section
The cables that link the switch to your computers plug in
here. Each KVM port section is comprised of a microphone
jack, speaker jack(s), USB type B socket and a DVI
connector.
3 power jack The power adapter cable plugs into this jack.
4 USB 2.0
hub
USB 2.0 peripherals (printers, scanners, etc.) can plug into
this port (this may require an extra power adapter).
cs1782a-1784a.book Page 10 Monday, July 19, 2021 4:50 PM
11
Chapter 2
Hardware Setup
Cable Connections
To set up your CS1782
A
/ CS1784
A
installation, refer to the installation
diagram on the following page (the numbers in the diagrams correspond to the
steps, below), and do the following:
1. Plug your USB keyboard and USB mouse into the USB console ports
located on the unit’s rear panel.
2. Plug your console monitor into the DVI console port located in the unit’s
rear panel and power on the monitor.
3. Plug your main microphone and speakers into the console microphone and
speaker jacks located on the unit’s front panel. The microphone and
speakers plugged into this panel have priority over those in the rear panel.
4. Plug your secondary microphone and 2.1 / 7.1 speakers into the console
audio ports located on the unit’s rear panel.
4a. Plug one end of the 7.1 surround sound cable provided with the
package into the 7.1 channel audio ports on the CS1782
A
1. Important safety information regarding the placement of this
device is provided on page 43. Please review it before
proceeding.
2. To prevent damage to your installation from power surges or
static electricity. It is important that all connected devices are
properly grounded.
3. Make sure that power to all the devices you will be installing has
been turned off. You must unplug the power cords of any
computers that have the Keyboard Power On function.
4. Please operate the device with caution when under high
environmental temperatures, as the surface of the device may
become overheated under such conditions. For instance, the
surface temperature of the device may reach 70 °C (158 °F) or
higher when the environmental temperature reaches close 50 °C
(122 °F).
cs1782a-1784a.book Page 11 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
12
4b. Plug the other end of the 7.1 surround sound cable into the 7.1 channel
audio ports on your computer.
5. Using a KVM cable set (provided with this package), plug the DVI
connector into any available DVI socket in the KVM port section of the
switch, then plug the accompanying USB, microphone and speaker
connectors into their corresponding USB, microphone, and speaker
sockets.
Note: Verify that all the plugs are in the same KVM port sockets (all in port
1, all in port 2, etc.). Each socket is marked with an appropriate icon.
6. At the other end of the cable, plug the USB, video, microphone, and
speaker cables into their respective ports on the computer.
7. Plug your USB peripherals into the USB Type-A ports in the USB hub
section.
8. Plug the power adapter that came with your switch into an AC power
source, then plug power adapter cable into the switch’s power jack.
9. Power on the computers.
Note: Make sure the computers and devices that the CS1782A / CS1784A
connects to are also properly grounded.
cs1782a-1784a.book Page 12 Monday, July 19, 2021 4:50 PM
Chapter 2. Hardware Setup
13
Installation Diagram
25
8
6
USB DVI
KVM Cable Set
USB DVI
KVM Cable Set
6
4
7
13
cs1782a-1784a.book Page 13 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
14
CS1782A 7.1 Channel Surround Sound Installation
4
4b
7.1 Channel Surround Sound
Audio Cable Set
4a
cs1782a-1784a.book Page 14 Monday, July 19, 2021 4:50 PM
15
Chapter 3
Basic Operation
Overview
There are three convenient methods to access the computers: Manual – which
involves pressing the port selection pushbuttons located on the unit’s front
panel; Mouse – which involves clicking the scroll wheel of the mouse; and
Hotkey – which involves entering combinations from the keyboard. Hotkey
port selection is discussed in the next chapter.
Manual Switching
For manual port selection:
Press and hold a port selection pushbutton for more than 2 seconds to
bring the KVM focus to the computer attached to its corresponding port.
The USB and Audio focus does not change – they stay with the port that
they are already on.
Press a port selection pushbutton twice to bring the audio focus to the
computer attached to its corresponding port.
Press and release a port selection pushbutton to bring the KVM focus, plus
the USB and Audio focus to the computer attached to its corresponding
port.
Press and hold port selection pushbutton 1 and 2 for more than 2 seconds
to start Auto Scan Mode, see page 24 for details.
Press and release either port selection pushbutton to stop Auto Scan Mode.
The KVM focus goes to the computer attached to the corresponding port
of the switch you pressed.
cs1782a-1784a.book Page 15 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
16
Mouse Port Switching
The CS1782
A
/ CS1784
A
supports the very latest in mouse port-switching –
simply double-click the scroll wheel of your USB mouse to cycle through the
ports.
Note: 1. This featured is only supported by USB 3-key scroll wheel mice.
2. The default setting is disabled.
3. This feature is only supported when Mouse Emulation is enabled. See
Mouse Emulation Control, page 30, for details.
Hot Plugging
The CS1782
A
/ CS1784
A
supports USB hot plugging – components can be
removed and added back into the installation by unplugging their cables from
the USB hub ports without the need to shut the unit down.
Powering Off and Restarting
If it becomes necessary to Power Off the CS1782
A
/ CS1784
A
unit, before
starting it back up you must do the following:
1. Shut down all the computers that are attached to the switch.
2. Unplug the switch’s power adapter cable.
3. Wait 10 seconds, then plug the switch’s power adapter cable back in.
4. After the switch is up, Power On the computers.
cs1782a-1784a.book Page 16 Monday, July 19, 2021 4:50 PM
Chapter 3. Basic Operation
17
Port ID Numbering
Each KVM port section on the CS1782
A
/ CS1784
A
switch is assigned a port
number. (1 or 2 for the CS1782
A
; 1 to 4 for the CS1784
A
). The port numbers
are marked on the rear panel of the switch (see page 9 for details).
The Port ID of a computer is derived from the KVM port number it is
connected to. For example, a computer connected to KVM port 2 has a Port ID
of 2.
The Port ID is used to specify which computer gets the KVM, USB peripheral,
and audio focus with the Hotkey port selection method (see page 21 for
details).
Alternative Manual Port Selection Settings
When Hotkey Setting Mode has been activated, pressing [S] will invoke the
alternative front panel pushbutton manual port selection functions as follows
(see page 29, also):
Press and hold a port selection pushbutton for more than 2 seconds to
bring the KVM, audio and USB focus to the computer attached to its
corresponding port.
Press a port selection pushbutton twice to bring the audio focus to the
computer attached to its corresponding port.
Press a port selection pushbutton once to bring only the KVM focus to the
computer attached to its corresponding port.
Press and hold port selection pushbuttons 1 and 2 for more than 2 seconds
to start Auto Scan Mode, see page 24 for details.
cs1782a-1784a.book Page 17 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
18
This Page Intentionally Left Blank
cs1782a-1784a.book Page 18 Monday, July 19, 2021 4:50 PM
19
Chapter 4
Hotkey Operation
The CS1782
A
/ CS1784
A
provides an extensive, easy-to-use, hotkey function
that makes it convenient to control and configure your KVM installation from
the keyboard. Hotkeys provide independent switching of the KVM, USB hub,
and audio focus. Therefore, you can give one computer the KVM focus,
another the USB hub focus, while a third has the audio focus.
Port Switching
All port switches begin with tapping the Scroll Lock key twice. The tables
below describe the actions that each combination performs.
Note: If using the Scroll Lock key conflicts with other programs running on
the computer, the Ctrl key can be used, instead. See Alternate Port
Switching Keys, page 26 for details.
Cycling Through the Ports
Hotkey Action
[Scroll Lock] [Scroll Lock]
[Enter]
Brings the KVM, USB hub, and audio focus from the
port that currently has the KVM focus to the next port on
the installation (1 to 2; 2 to 1 for the CS1782
A
; 1 to 2; 2
to 3; 3 to 4; 4 to 1 for the CS1784A).
Note: The KVM, USB hub, and audio focus all go to this
port even if they were on different ports to begin with.
[Scroll Lock] [Scroll Lock]
[K] [Enter]
Brings only the KVM focus from the port that currently
has it to the next port on the installation. The USB and
audio focus remain where they are.
[Scroll Lock] [Scroll Lock]
[U] [Enter]
Brings only the USB hub focus from the port that
currently has it to the next port on the installation. The
KVM and audio focus remain where they are.
[Scroll Lock] [Scroll Lock]
[S] [Enter]
Brings only the audio focus from the port that currently
has it to the next port on the installation. The KVM and
USB hub focus remain where they are.
cs1782a-1784a.book Page 19 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
20
Example 1
To bring the KVM, USB hub, and audio focus from port 1 to port 2, do the
following:
1. Press [Scroll Lock] twice.
2. Press [Enter].
Example 2
To bring the KVM focus from port 1 to port 2, do the following:
1. Press [Scroll Lock] twice.
2. Press [K].
3. Press [Enter].
Example 3
To bring the USB hub focus from port 1 to port 2, do the following:
1. Press [Scroll Lock] twice.
2. Press [U].
3. Press [Enter].
Example 2
To bring the audio focus from port 1 to port 2, do the following:
1. Press [Scroll Lock] twice.
2. Press [S].
3. Press [Enter].
cs1782a-1784a.book Page 20 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
21
Going Directly to a Port
Note: The n stands for the computer’s Port ID number (1, 2, 3, or 4). See Port
ID Numbering, page 17. Replace the n with the appropriate Port ID
when entering hotkey combinations.
Example 1
To bring the KVM, USB hub, and audio focus from a port to a specified port
number (e.g., port 2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [Enter].
Hotkey Action
[Scroll Lock] [Scroll Lock]
[n] [Enter]
Brings the KVM, USB hub, and audio focus to the
computer attached to the port corresponding to the
specified Port ID.
Note: The KVM, USB hub, and audio focus all go to this
port even if they were on different ports to begin with.
[Scroll Lock] [Scroll Lock]
[n] [K] [Enter]
Brings only the KVM focus to the computer attached to
the specified port. The USB hub and audio focus remain
where they are.
[Scroll Lock] [Scroll Lock]
[n] [U] [Enter]
Brings only the USB hub focus to the computer
attached to the specified port. The KVM and audio focus
remain where they are.
[Scroll Lock] [Scroll Lock]
[n] [S] [Enter]
Brings only the audio focus to the computer attached to
the specified port. The KVM and USB hub focus remain
where they are.
[Scroll Lock] [Scroll Lock]
[n] [K] [U] [Enter]
Brings the KVM and USB hub focus to the computer
attached to the specified port. The audio focus remains
where it is.
[Scroll Lock] [Scroll Lock]
[n] [K] [S] [Enter]
Brings the KVM and audio focus to the computer
attached to the specified port. The USB hub focus
remains where it is.
[Scroll Lock] [Scroll Lock]
[n] [U] [S] [Enter]
Brings the USB hub and audio focus to the computer
attached to the specified port. The KVM focus remains
where it is.
cs1782a-1784a.book Page 21 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
22
Example 2
To bring only the KVM focus from a port to a specified port number (e.g., port
2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [K].
4. Press [Enter].
Example 3
To bring only the USB hub focus from a port to a specified port number (e.g.,
port 2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [U].
4. Press [Enter].
Example 4
To bring only the audio focus from a port to a specified port number (e.g., port
2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [S].
4. Press [Enter].
Example 5
To bring the KVM and USB hub focus from a port to a specified port number
(e.g., port 2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [K], and then press [U].
4. Press [Enter].
cs1782a-1784a.book Page 22 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
23
Example 6
To bring the KVM and audio focus from a port to a specified port number (e.g.,
port 2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [K], and then press [S].
4. Press [Enter].
Example 7
To bring the USB hub and audio focus from a port to a specified port number
(e.g., port 2), do the following:
1. Press [Scroll Lock] twice.
2. Press [2].
3. Press [U], and then press [S].
4. Press [Enter].
cs1782a-1784a.book Page 23 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
24
Auto Scanning
The CS1782
A
/ CS1784
A
’s Auto Scan feature automatically cycles the KVM
focus through the computer ports at regular intervals. This allows you to
monitor the computer activity without having to take the trouble of switching
from port to port manually. Although the video focus switches from port to
port, the keyboard, mouse, and USB focus doesn’t switch. They stay at the port
they were on when Auto Scanning started.See the table below for details. .
Note: 1. While Auto Scan Mode is in effect, ordinary keyboard and mouse
functions are suspended – only Auto Scan Mode compliant
keystrokes and mouse clicks can be input. You must exit Auto Scan
Mode (press the Esc key or the Spacebar) in order to regain normal
control of the console.
2. Although the video focus switches from port to port, the keyboard and
mouse do not switch. They stay at the port they were on when Auto
Scanning started.
3. To exit Auto Scan Mode, press the ESC key or the Spacebar.
Hotkey Action
[Scroll Lock] [Scroll
Lock] [A] [Enter]
Invokes Auto Scan. The KVM focus cycles from port to port
at 5 second intervals. Five second intervals is the Default
setting.
[Scroll Lock] [Scroll
Lock] [A] [n] [Enter]
The KVM focus cycles from port to port at n second intervals.
Note: The n stands for the number of seconds that the
CS1782A / CS1784A should dwell on a port before moving
on to the next. Replace the n with a number between 1 and
99 when entering this hotkey combination
cs1782a-1784a.book Page 24 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
25
Hotkey Setting Mode
Hotkey Setting Mode is used to set up your CS1782
A
/ CS1784
A
switch
configuration. All operations begin with invoking Hotkey Setting Mode
(HSM).
Invoking HSM
To invoke HSM do the following:
1. Press and hold down [Num Lock].
2. Press and release [-].
3. Release [Num Lock].
Note: 1. There is an alternate key combination to invoke HSM. See page 26
for details.
2. The minus key must be released within one half second, otherwise
Hotkey invocation is canceled.
When HSM is active, the Caps Lock, and Scroll Lock LEDs flash in succession
to indicate that HSM is in effect. They stop flashing and revert to normal status
when you exit HSM.
Ordinary keyboard and mouse functions are suspended – only Hotkey
compliant keystrokes and mouse clicks (described in the sections that follow),
can be input.
At the conclusion of some hotkey operations, you automatically exit hotkey
mode. With some operations, you must exit manually. To exit HSM manually,
press the Esc key, or the Spacebar.
cs1782a-1784a.book Page 25 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
26
Alternate HSM Invocation Keys
An alternate set of HSM invocation keys is provided in case the default set
conflicts with programs running on the computers.
To switch to the alternate HSM invocation set, do the following:
1. Invoke HSM (see page 25)
2. Press and release [H].
The HSM invocation keys become the Ctrl key (instead of Num Lock) and
the F12 key (instead of minus).
Note: This procedure is a toggle between the two methods. To revert back to
the original HSM invocation keys, invoke HSM, then press and release
the H key again.
Alternate Port Switching Keys
The port switching activation keys can be changed from tapping the Scroll
Lock key twice ([Scroll Lock] [Scroll Lock]) to tapping the Ctrl key twice
([Ctrl] [Ctrl]). To change the port switching activation keys, do the following:
1. Invoke HSM (see page 25)
2. Press and release [T] .
Note: This procedure is a toggle between the two methods. To revert back to
the original [Scroll Lock] [Scroll Lock] method, invoke HSM, then
press and release the T key again.
cs1782a-1784a.book Page 26 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
27
Keyboard Operating Platform
The CS1782
A
/ CS1784
A
’s default port configuration is for a PC compatible
keyboard operating platform. If your console uses a PC compatible keyboard
and you have a Mac attached to a port, for example, you can change the port’s
keyboard operating platform configuration so that the PC compatible keyboard
emulates the Mac keyboard. The procedure is as follows:
1. Bring the KVM focus to the port you want to set.
2. Invoke HSM (see page 25)
3. Press and release the appropriate Function key (see table below). After
completing this procedure, you automatically exit HSM.
Note: To set the keyboard language, see Keyboard Language, page 28.
List Switch Settings
To see a listing of the current switch settings, do the following:
1. Open a text editor or word processor and place the cursor in the page
window.
2. Invoke HSM (see page 25).
3. Press and release [F4] to display the settings.
Function Key Operation
[F2] Enables Mac keyboard emulation, see Mac Keyboard,
page 35 for details.
[F3] Enables Sun keyboard emulation, see Sun Keyboard,
page 36 details.
[F10] Auto detects the keyboard operating platform (for PC
compatible systems). Activates Pass Through keyboard
mode (keystrokes are sent directly to the computer
instead of through the Mac or Sun emulator).
cs1782a-1784a.book Page 27 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
28
USB Reset
If the USB loses focus and needs to be reset, do the following:
1. Invoke HSM (see page 25).
2. Press and release [F5].
Keyboard Language
To change the keyboard language, do the following:
1. Invoke HSM (see page 25).
2. Press [F6] [nn] [Enter].
Note: nn is a two-digit number that represents the keyboard language code
(US English: 33; French: 08; Japanese: 15).
Hotkey Buzzer Control
The Buzzer can be enabled or disabled. The default setting is enabled. To
disable the Buzzer, do the following:
1. Invoke HSM (see page 25).
2. Press and release [B].
This procedure is a toggle. Repeat to enable.
Port Switching Keys
The Port Switching Keys ([Scroll Lock] [Scroll Lock] / [Ctrl] [Ctrl]) can be
enabled or disabled. The default setting is enabled. To disable, do the
following:
1. Invoke HSM (see page 25).
2. Press [X] [Enter].
This procedure is a toggle. Repeat to enable.
cs1782a-1784a.book Page 28 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
29
Firmware Upgrade Mode
To set the CS1782
A
/ CS1784
A
to Firmware Upgrade Mode, do the following:
1. Invoke HSM (see page 25).
2. Key in: upgrade
3. Press [Enter]. The orange front panel LEDs flash to indicate Firmware
Upgrade Mode is in effect.
Note: To exit Firmware Upgrade Mode, you must power off the switch.
See The Firmware Upgrade Utility, page 37, for details.
Restore Default Settings
To reset the CS1782
A
/ CS1784
A
to its default hotkey settings, do the
following:
1. Invoke HSM (see page 25).
2. Press [R] [Enter].
See Hotkey Default Settings, page 50
Video DynaSync
Video DynaSync is ATEN’s exclusive technology that eliminates boot-up
display problems and optimizes resolution when switching between ports. To
invoke Video DynaSync, do the following:
1. Invoke HSM (see page 25)
2. Press [D].
Note: If the monitor is disconnected and reconnected, the CS1782
A
/
CS1784
A
re-executes Video DynaSync.
Alternative Manual Port Selection Settings
To toggle between the default and the alternative front panel pushbutton
manual port selection settings, do the following:
1. Invoke HSM (see page 25)
2. Press [S].
See Alternative Manual Port Selection Settings, page 17, for full details.
cs1782a-1784a.book Page 29 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
30
Mouse Emulation Control
The default setting is enabled. To disable, do the following:
1. Invoke HSM (see page 25).
2. Press [M].
This procedure is a toggle. Repeat to enable.
Mouse Port-switching
The Mouse Port-switching function can be enabled or disabled. The default
setting is disabled. To enable, do the following:
1. Invoke HSM (see page 25).
2. Press [W].
This procedure is a toggle. Repeat to disable.
Note: This feature is only supported by USB 3-key scroll wheel mice. The
default setting is OFF. This feature is only supported when mouse
emulation is also enabled. See Mouse Emulation Control, above.
Keyboard Emulation Control
Console keyboard port emulation/bypass feature supports most gaming/
multimedia keyboards. The default setting is enabled. To disable, do the
following:
1. Invoke HSM (see page 25).
2. Press [N].
3. This procedure is a toggle. Repeat to enable.
Note: When keyboard emulation is disabled, the [M], [W], [F2], [F3], [F4],
[F5], [F6], and [F10] are disabled. See page 32, for details.
SPC Mode
To set the keyboard/mouse to use SPC mode so that it can work under special
operating systems as a standard (104 key) keyboard/mouse, do the following:
1. Invoke HSM (see page 25).
2. Press [F1].
cs1782a-1784a.book Page 30 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
31
Power on Detection
With Power on Detection if the focus computer is powered off, the switch will
automatically switch to the next powered-on computer. Power on Detection
can be enabled or disabled. The default setting is enabled. To disable Power on
Detection, do the following:
1. Invoke HSM (see page 25).
2. Press and release [E].
This setting is a toggle. Repeat to enable.
cs1782a-1784a.book Page 31 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
32
HSM Summary Table
After invoking HSM (see page 25), key in one of the following keys to perform
the corresponding function:
Key Function
[H] Toggles between the default ([Num Lock] [-]) and alternate ([Ctrl]
[F12]) HSM invocation keys.
[T] Toggles between the default ([Scroll Lock] [Scroll Lock]) and alternate
([Ctrl] [Ctrl]) Port Switching keys.
[F2] Enables Mac keyboard emulation.
[F3] Enables Sun keyboard emulation.
[F10] Automatically detects and sets the keyboard operating platform.
[F4] Lists the current switch settings via the paste function of a text editor.
[F5] Performs a reset on all USB devices.
[F6] [nn]
[Enter]
Sets the keyboard language.
Note: nn is a two-digit number that represents one of the following
keyboard language code: US English: 33; French: 08; Japanese: 15.
[B] Enables/Disables the buzzer.
[X] [Enter] Enables/Disables the port switching keys.
[R] [Enter] Resets the hotkey settings to their default status.
[u] [p] [g] [r] [a]
[d] [e] [Enter]
Invokes Firmware Upgrade Mode. See The Firmware Upgrade Utility,
page 37, for full details.
[D] Invokes Video DynaSync, ATEN’s exclusive technology that
eliminates boot-up display problems and optimizes resolution when
switching between ports.
[E] Enables/Disables the Power on Detection feature. See Power on
Detection, page 31 for details.
[S] Toggles between the default and alternate manual port selection
pushbutton settings.
[N] Enables/Disables keyboard emulation.
[M] Enables/Disables mouse emulation.
[W] Enables/Disables mouse port-switching.
cs1782a-1784a.book Page 32 Monday, July 19, 2021 4:50 PM
Chapter 4. Hotkey Operation
33
[F1] Sets the SPC mode so that it can work under special operating
systems as a standard (104 key) keyboard/mouse.
Key Function
cs1782a-1784a.book Page 33 Monday, July 19, 2021 4:50 PM
CS1782A / CS1784A User Manual
34
This Page Intentionally Left Blank
cs1782a-1784a.book Page 34 Monday, July 19, 2021 4:50 PM
35
Chapter 5
Keyboard Emulation
Mac Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Mac keyboard. The emulation mappings are listed in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Mac Keyboard
[Shift] Shift
[Ctrl] Ctrl
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Alt] Alt
[Print Screen] F13
[Scroll Lock] F14
=
[Enter] Return
[Backspace] Delete
[Insert] Help
[Ctrl] F15
cs1782a-1784a.book Page 35 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
36
Sun Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Sun keyboard when the Control key [Ctrl] is used in conjunction with other
keys. The corresponding functions are shown in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Sun Keyboard
[Ctrl] [T] Stop
[Ctrl] [F2] Again
[Ctrl] [F3] Props
[Ctrl] [F4] Undo
[Ctrl] [F5] Front
[Ctrl] [F6] Copy
[Ctrl] [F7] Open
[Ctrl] [F8] Paste
[Ctrl] [F9] Find
[Ctrl] [F10] Cut
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Ctrl] [H] Help
Compose
-
+
cs1782a-1784a.book Page 36 Monday, July 19, 2021 4:50 PM
37
Chapter 6
The Firmware Upgrade Utility
The Windows-based Firmware Upgrade Utility (FWUpgrade.exe) provides a
smooth, automated process for upgrading the KVM switch’s firmware. The
Utility comes as part of a Firmware Upgrade Package that is specific for each
device. Check the web site regularly to find the latest packages and information
relating to them: http://www.aten.com
Before you Begin
1. From a computer that is not part of your KVM installation go to our
Internet support site and choose the model name that relates to your device
(CS1782
A
/ CS1784
A
) to get a list of available Firmware Upgrade
Packages.
2. Choose the Firmware Upgrade Package you want to install (usually the
most recent), and download it to your computer.
3. Power off the switch. Unplug the KVM cables from the back of the switch.
If you are using a power adapter, unplug it and remove its connector from
the switch’s power jack. Connect one of the USB DVI KVM cable set’s
USB Type-A connectors to a USB hub port on your computer.
4. At the other end of the USB DVI KVM cable set, connect the USB Type-B
connector to the USB Type-A port in the port 1 KVM section.
Note: The USB DVI KVM cable set’s USB Type-B connector can be
connected to any USB Type-B KVM port section, but the port
selection pushbutton to invoke Firmware Upgrade Mode in Step 5,
below must be port 1.
cs1782a-1784a.book Page 37 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
38
5. To invoke Firmware Upgrade Mode, press and hold the port 1 selection
pushbutton. While holding the button, plug the power adapter to the
switch’s power jack. The front panel orange LEDs flash to indicate that
Firmware Upgrade Mode is in effect.
USB DVI
KVM Cable Set
4
3
cs1782a-1784a.book Page 38 Monday, July 19, 2021 4:50 PM
Chapter 6. The Firmware Upgrade Utility
39
Starting the Upgrade
1. Run the downloaded Firmware Upgrade Package file – either by double
clicking the file icon, or using a command line to enter the full path.
The Firmware Upgrade Utility Welcome screen appears:
2. Read the License Agreement (enable the I Agree radio button).
3. Click Next. The Firmware Upgrade Utility main screen appears. The
Utility inspects your installation. All the devices capable of being
upgraded by the package are listed in the Device List panel.
(Continues on next page.)
cs1782a-1784a.book Page 39 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
40
4. As you select a device in the list, its description appears in the Device
Description panel.After you have made your device selection(s), Click
Next to perform the upgrade.
If you enabled Check Firmware Version, the Utility compares the device’s
firmware level with that of the upgrade files. If the device’s version is
higher than the upgrade version, a dialog box gives you the option to
Continue or Cancel.
If you didn’t enable Check Firmware Version, the Utility installs the
upgrade files without checking whether they are a higher level, or not.
cs1782a-1784a.book Page 40 Monday, July 19, 2021 4:50 PM
Chapter 6. The Firmware Upgrade Utility
41
Upgrade Succeeded
After the upgrade has completed, a screen appears to inform you that the
procedure was successful:
Click Finish to close the Firmware Upgrade Utility.
After a successful completion, the CS1782
A
/ CS1784
A
exits Firmware
Upgrade Mode, and resets itself.
Upgrade Failed
If the Upgrade Succeeded screen doesn’t appear, it means that the upgrade
failed to complete successfully, in which case you should do the following:
1. Power off the CS1782
A
/ CS1784
A
by removing the power jack.
2. Invoke Firmware Upgrade Mode by holding down the port 1 selection
pushbutton in the front panel (see Components, page 7) and power on the
CS1782
A
/ CS1784
A
. The orange LEDs flash together.
3. Do the firmware upgrade procedure again.
cs1782a-1784a.book Page 41 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
42
This Page Intentionally Left Blank
cs1782a-1784a.book Page 42 Monday, July 19, 2021 4:50 PM
43
Appendix
Safety Instructions
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
To prevent damage to your installation, it is important that all devices are
properly grounded.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
cs1782a-1784a.book Page 43 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
44
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
cs1782a-1784a.book Page 44 Monday, July 19, 2021 4:50 PM
Appendix
45
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://eservice.aten.com
For telephone support, see Telephone Support, page vii.
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration, including operating system, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
1-949-428-1111
cs1782a-1784a.book Page 45 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
46
Specifications
Function CS1782A
Computer Connections 2
Port Selection Front Panel Pushbuttons, Hotkeys, Mouse
Connectors
Console
Ports
Keyboard 1 x USB Type-A Female (Black; rear panel)
Video 1 x DVI-I Female (white)
Mouse 1 x USB Type-A Female (Black; rear panel)
Audio Line out 2 x Mini Stereo Jack Female (Green; 1 x front
panel, 1 x rear panel)
Line In 1 x Mini Stereo Jack Female (Blue)
Side Speaker out
1 x Mini Stereo Jack Female (Gray)
Rear Speaker out
1 x Mini Stereo Jack Female (Black)
Center/Subwoofer
1 x Mini Stereo Jack Female (Orange)
Microphone
2 x Mini Stereo Jack F (Pink; 1 x front panel, 1 x
rear panel)
KVM
Ports
Keyboard/Mouse 2 x USB Type-B Female (White)
Video 2 x DVI-I F (White)
Audio Line out 2 x Mini Stereo Jack Female (Green)
Line In 2 x Mini Stereo Jack Female (Blue)
Side Speaker out
2 x Mini Stereo Jack Female (Gray)
Rear Speaker out
2 x Mini Stereo Jack Female (Black)
Center/Subwoofer
2 x Mini Stereo Jack Female (Orange)
Microphone
2 x Mini Stereo Jack Female (Pink)
Power 1 x DC Jack
USB 2.0 Hub 2 x USB Type-A Female (White; 1 x front panel,
1 x rear panel)
Switches Selected 2 x Pushbutton
LEDs On Line / Selected 2 (Orange)
USB Link 2 (Green)
Emulation Keyboard / Mouse USB
Video Dual Link DVI: 2560 x 1600
Single Link DVI: 1920 x 1200
Scan Interval 1–99 secs. (5 secs. default)
Power Consumption DC 5.3V, 3.3W
Environment
Operating Temp. 0–50ºC
Storage Temp. -20–60ºC
Humidity 0–80% RH, Non-condensing
Physical
Properties
Housing Metal
Weight 0.90 kg
Dimensions (L x W x H) 27.00 x 8.80 x 5.55 cm
cs1782a-1784a.book Page 46 Monday, July 19, 2021 4:50 PM
Appendix
47
Function CS1784A
Computer Connections 4
Port Selection Front Panel Pushbuttons, Hotkeys, Mouse
Connectors
Console
Port
s
Keyboard 1 x USB Type-A Female (Black; rear panel)
Video 1 x DVI-I Female (white)
Mouse 1 x USB Type-A Female (Black; rear panel)
Audio Speaker 2 x Mini Stereo Jack Female (Green; 1 x front panel, 1
x rear panel)
Microphone
2 x Mini Stereo Jack F (Pink; 1 x front panel, 1 x rear
panel)
KVM
Ports
Keyboard/Mouse 4 x USB Type-B Female (White)
Video 4 x DVI-I F (White)
Audio Speaker 4 x Mini Stereo Jack Female (Green)
Microphone
4 x Mini Stereo Jack Female (Pink)
Power 1 x DC Jack
USB 2.0 Hub 2 x USB Type-A Female (White; 1 x front panel, 1 x
rear panel)
Switches Selected 4 x Pushbutton
LEDs On Line / Selected 4 (Orange)
USB Link 4 (Green)
Emulation Keyboard / Mouse USB
Video Dual Link DVI: 2560 x 1600
Single Link DVI: 1920 x 1200
Scan Interval 1–99 secs. (5 secs. default)
Power Consumption DC 5.3V, 5.91W
Environment
Operating Temp. 0–50ºC
Storage Temp. -20–60ºC
Humidity 0–80% RH, Non-condensing
Physical
Properties
Housing Metal
Weight 0.93 kg
Dimensions (L x W x H) 27.00 x 8.80 x 5.55 cm
cs1782a-1784a.book Page 47 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
48
Troubleshooting
Operation problems can be due to a variety of causes. The first step in solving
them is to make sure that all cables are securely attached and seated completely
in their sockets. In addition, updating the product’s firmware may solve
problems that have been discovered and resolved since the prior version was
released. If your product is not running the latest firmware version, we strongly
recommend that you upgrade. See Chapter 6, The Firmware Upgrade Utility,
for details.
(Continues on next page.)
Symptom Possible Cause Action
Mouse and/or
Keyboard not
responding.
Improper mouse
and/or keyboard
reset.
Unplug the cable(s) from the console port(s),
then plug it/them back in.
KVM switch
needs to be reset.
Power off all devices on the installation (see
safety note, page 43); power off the KVM
switch; wait five seconds; then power up.
USB devices not
responding.
USB ports need to
reset.
Unplug the device’s USB cable from the USB
port on the switch’s rear panel, then plug it
back in.
PC or OS does
not support USB
2.0.
The unit has a built-in USB 2.0 hub, so does
not support PCs or OS that do not support
USB 2.0.
For OS that do not support USB 2.0, keyboard
and mouse functions can be reset using the
[F1] hotkey function. See SPC Mode, page 30.
Device not
recognized
(Windows).
Windows timing
problem.
Unplug the KVM cable from the computer’s
USB port; go into Windows’ System Settings
and remove the Unknown Device entry; plug
the KVM cable back in. Windows now
recognizes the device.
Cannot switch
ports by pressing
[Scroll Lock]
twice.
Keyboard is
incompatible with
Scroll Lock
invocation.
Switch to the Alternate HSM invocation keys.
See Alternate HSM Invocation Keys, page 26,
for details.
Monitor does not
display after KVM
cable set is hot
plugged.
Some HDMI/DVI
graphics cards
are incompatible
with cable set hot
plugging.
Power off all devices on the installation (see
safety note, page 43); power off the CS1784A;
confirm all KVM cables are properly
connected; power on the CS1784A; power on
the computers.
cs1782a-1784a.book Page 48 Monday, July 19, 2021 4:50 PM
Appendix
49
(Continued from previous page.)
Symptom Possible Cause Action
When switching to
an HDMI
computer, there is
no display on the
monitor.
Graphics card is
DVI-I (Digital and
Analog).
Adjust the graphics card settings to digital
only.
Replace graphics card with DVI-D or HDMI
graphics card.
When switching
ports, the monitor
does not display.
Monitor is new or
this is the first
time installation.
Switch ports again and wait two or more
seconds for the monitor’s EDID to pass to the
PC.
The monitor’s
EDID has not
passed through to
the PC when
switching ports.
Use the [d] hotkey to invoke Video DynaSync
one more time or switch to another PC to
reconnect the CS1784A. See HSM Summary
Table, page 32.
Gaming keyboard
connected to USB
2.0 peripheral port
does not not work
properly.
KVM hotkeys are
not supported.
Toggle the Keyboard Emulation hotkey [N] off
and on again. See Keyboard Emulation
Control, page 30. Keyboard emulation must
be enabled to use all the keyboard’s special
keys.
cs1782a-1784a.book Page 49 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
50
Hotkey Default Settings
The hotkey factory default settings are as follows:
Setting Hotkey Default
Port Switching (Default /
Alternative)
[T] [Scroll Lock] [Scroll Lock]
Invoking HSM [H] [Number Lock] [-]
Auto Scan Interval [Scroll Lock]
[Scroll Lock]
[A] [Enter]
5 seconds
Keyboard Operating Platform [F10] PC Compatible
Mouse Emulation [M] Enabled
Mouse Port-switching [W] Disabled
Keyboard Emulation [N] Enabled
Video DynaSync [D] Enabled
Port Switching Keys (On / Off) [X] [Enter] Enabled
Buzzer [B] Enabled
Power on Detection [E] Enabled
Keyboard Language [F6] [nn] [Enter]
Note: nn is the
language number
English
cs1782a-1784a.book Page 50 Monday, July 19, 2021 4:50 PM
Appendix
51
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in
materials and workmanship for a Warranty Period of two [2] years (warranty
period may vary in certain regions/countries) commencing on the date of
original purchase. This warranty period includes the LCD panel of ATEN LCD
KVM switches. Select products are warranted for an additional year (see A+
Warranty for further details). Cables and accessories are not covered by the
Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty
Period. If a product is detective, ATEN will, at its discretion, have the option
to (1) repair said product with new or repaired components, or (2) replace the
entire product with an identical product or with a similar product which fulfills
the same function as the defective product. Replaced products assume the
warranty of the original product for the remaining period or a period of 90 days,
whichever is longer. When the products or components are replaced, the
replacing articles shall become customer property and the replaced articles
shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
cs1782a-1784a.book Page 51 Monday, July 19, 2021 4:50 PM
CS1782
A
/ CS1784
A
User Manual
52
MEMO
cs1782a-1784a.book Page 52 Monday, July 19, 2021 4:50 PM
Appendix
53
MEMO
cs1782a-1784a.book Page 53 Monday, July 19, 2021 4:50 PM
© Copyright 2021 ATEN® International Co., Ltd.
ATEN International Co., Ltd., 3F, No. 125, Sec. 2, Datung Rd., Sijhih District, New Taipei City 221, Taiwan
Phone: 886-2-8692-6789 Fax: 886-2-8692-6767 TECHNICAL SUPPORT CENTER: 886-2-8692-6959
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
Released: 2021-07-19
cs1782a-1784a.book Page i Monday, July 19, 2021 4:50 PM