Table of Contents
- CS1768 / CS1788
- EMC Information
- RoHS
- User Information
- Package Contents
- Contents
- About this Manual
- Conventions
- Product Information
- Chapter 1 Introduction
- Chapter 2 Hardware Setup
- Chapter 3 Basic Operation
- Chapter 4 OSD Operation
- Chapter 5 Hotkey Operation
- Chapter 6 Keyboard Emulation
- Chapter 7 The Firmware Management Utility
- Appendix
ATEN CS1788-AT-G User Manual
Displayed below is the user manual for CS1788-AT-G by ATEN which is a product in the KVM Switches category. This manual has pages.
Related Manuals
8-Port USB DVI KVM Switch
CS1768 / CS1788
User Manual
www.aten.com
CS1768 / CS1788 User Manual
ii
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
Warning: Operation of this equipment in a residential environment could
cause radio interference.
Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann
Funkstörungen verursachen.
KCC Statement
RoHS
This product is RoHS compliant.
CS1768 / CS1788 User Manual
iii
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
CS1768 / CS1788 User Manual
iv
Package Contents
1 CS1768 / CS1788 8-Port USB DVI KVM Switch
with Rack Mounting Kit
2 Custom USB DVI-D KVM Cable Sets
1 Firmware Upgrade Cable
1 Power Adapter
1 Foot Pad Set (4 pcs)
1 User Instructions*
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
*Features may have been added to the CS1768 / CS1788 since this manual
was published. Please visit our website to download the most up-to-date
version.
© Copyright 2020 ATEN® International Co., Ltd.
Manual Date: 2020-09-15
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
CS1768 / CS1788 User Manual
v
Contents
EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Chapter 1.
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2.
Hardware Setup
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rack Mounting – Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Rack Mounting – Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Single Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Console Monitor Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . 18
Single Stage Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Two Stage Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Three Stage Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Multi-display Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cable Connections for Multi-display Installation . . . . . . . . . . . . . . . . .26
Multi-display Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Grouping Ports into “Vertical” Channels . . . . . . . . . . . . . . . . . . . . . . . 28
Channels Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CS1768 / CS1788 User Manual
vi
Chapter 3.
Basic Operation
Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Manual Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 4.
OSD Operation
OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
OSD Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
OSD Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
F3: SET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Chapter 5.
Hotkey Operation
Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Invoke Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Select the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Invoking Auto Scan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Skip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Quick Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
OSD Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Port OS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Set USB Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Restore Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
CS1768 / CS1788 User Manual
vii
USB Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Hotkey Buzzer Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Restore Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Video DynaSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Mouse Emulation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
HSM Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Chapter 6.
Keyboard Emulation
Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Chapter 7.
The Firmware Management Utility
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 63
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
OSD Configuration Backup/Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
CS1768 / CS1788 Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Factory Default Hotkeys and Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
CS1768 / CS1788 User Manual
viii
About this Manual
This User Manual is provided to help you get the most from your CS1768 /
CS1788 system. It covers all aspects of installation, configuration and
operation. An overview of the information found in the manual is provided
below.
Chapter 1, Introduction, introduces you to the CS1768 / CS1788 system.
Its purpose, features and benefits are presented, and its front and back panel
components are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary steps for a basic single stage hookup, three-stage cascade, and multi-
display installation are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the CS1768 / CS1788.
Chapter 4, OSD Operation, provides a complete description of the
CS1768 / CS1788's OSD (On Screen Display), and how to work with it.
Chapter 5, Hotkey Operation, details all of the concepts and procedures
involved in the Hotkey operation of your CS1768 / CS1788 installation.
Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac
and PC to Sun keyboard emulation mappings.
Chapter 7, The Firmware Management Utility, explains how to use this
utility to upgrade the CS1768 / CS1788's firmware with the latest available
versions and perform an OSD configuration backup/restore.
An
Appendix, provides specifications and other technical information
regarding the CS1768 / CS1788.
CS1768 / CS1788 User Manual
ix
Conventions
This manual uses the following conventions:
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
→
Run means to
open the Start menu, and then select Run.
Indicates critical information.
International http://www.aten.com
North America http://www.aten-usa.com
CS1768 / CS1788 User Manual
x
This Page Intentionally Left Blank
1
Chapter 1
Introduction
Overview
The CS1768 / CS1788 is a control unit that allows access and control of up to
8 computers from a single USB keyboard, USB mouse, and monitor (DVI or
VGA) console. The CS1768 supports Single Link DVI; the CS1788 supports
Dual Link DVI. The CS1768 / CS1788 can be cascaded to three levels –
allowing up to 73 units to control up to 512 computers – all from the original
single console. In addition the CS1768 / CS1788 features multi-display
functionality, which enables the use of standard USB cables to stack up to four
switches in multiple-monitor installations where each computer is fitted with
multiple video cards. Furthermore, the CS1768 / CS1788 comes with ATEN’s
Video DynaSync
TM
technology, which optimizes display resolution.
There are three convenient methods to access any computer connected to the
installation: (1) using the pushbutton port selection switches located on each
unit's front panel; (2) entering Hotkey combinations from the keyboard; and (3)
selecting from menus provided by the on-screen display (OSD).
The CS1768 / CS1788 provides multimedia keyboard support and is audio
enabled. Two microphones can provide audio input to each of the computers,
and you can listen to the audio output of each computer on two sets of speakers
(on a one-at-a-time basis).Setup is fast and easy; simply plug cables into their
appropriate ports. There is no software to configure, no installation routines,
and no incompatibility problems. Since the CS1768 / CS1788 intercepts
keyboard input directly, it works on multiple operating platforms (PC
compatible, Mac, Sun, etc.).
Since a single console manages all of the computers on your installation, a
CS1768 / CS1788 KVM switch setup: (1) eliminates the expense of having to
purchase a separate keyboard, monitor, and mouse for each computer; (2) saves
all the space those extra components would take up; (3) saves on energy costs;
and (4) eliminates the inconvenience and wasted effort involved in constantly
moving from one computer to another.
Note: The CS1768 / CS1788 offers two types of installation – 1) standalone/
cascade; and 2) multi-display – that require different cabling setups.
Therefore, the functions of both types are not available in one
installation.
CS1768 / CS1788 User Manual
2
Features
One USB console controls eight Single Link DVI (CS1768) / Dual Link
DVI (CS1788) or VGA computers and two additional USB 2.0 devices
Supports both digital (DVI) and analog (VGA) video – mixed operation
possible
Cascadable to three levels – control up to 512 computers
Multi-display feature – stack up to four CS1768 / CS1788 units and
display video from up to four monitors (dual display / triple display / quad
display)
2-port USB 2.0 hub built in*
Fully compliant with the USB 2.0 specification
Computer selection via front panel pushbuttons, hotkeys, and multilingual
on-screen display (OSD)
Independent switching of KVM and USB focus
Broadcast mode – allows you to send commands from the console to all
computers to perform operations simultaneously.
OSD Backup/Restore feature – enables the administrator to back up the
switch’s configuration and user profile information
Firmware upgradable
DVI digital and analog monitor support – fully compliant with the DVI
specifications
Video DynaSync
TM
– exclusive ATEN technology eliminates boot-up
display problems and optimizes resolution when switching between ports
Superior video quality – 1920 x 1200 (Single Link DVI – CS1768) / 2560
x 1600 (Dual Link DVI – CS1788); 2048 x 1536 (VGA); DDC2B
Supports widescreen resolutions
Audio enabled – full bass response provides a rich experience for 2.1
channel surround sound systems
Console audio ports on front panel for easy access
Auto Scan Mode for monitoring all computers
HDCP compatible
1. Introduction
3
Multiplatform support – Windows, Linux, Mac**, Sun**
Console mouse port emulation/bypass feature supports most mouse
drivers and multifunction mice
Complete keyboard emulation for error-free booting
Mac/Sun keyboard support and emulation***
Multilingual OSD supports English, German, Japanese, Traditional
Chinese, Simplified Chinese, Spanish, Russian, and French
Multilingual keyboard mapping – supports English (US), English (UK),
French, German, Japanese, Korean, Traditional Chinese, and Spanish
Note: 1. The USB 2.0 hub cannot be accessed through the switch by
computers on the second or third level of a cascaded installation.
2. For PC compatible computers. Mac and Sun computers must use
the USB cable connections (see Cables, page 5).
3. PC keyboard combinations emulate Mac/Sun keyboards; Mac/
Sun keyboard work only with their own computers
CS1768 / CS1788 User Manual
4
Requirements
Console
A DVI compatible monitor capable of the highest possible resolution that
you will be using on any computer in the installation
Note: For multi-display installations, multiple monitors are required. See
Multi-display Installation, page 26, for details.
A VGA, SVGA, XGA, SXGA or multisync monitor capable of the highest
resolution that you will be using on any computer in the installation
(optional)
A USB mouse
A USB keyboard
Microphone and speakers (optional)
Computers
The following equipment must be available on each computer:
A DVI card
Note: 1. The quality of the display is affected by the quality of the DVI
display card. For best results, we recommend you purchase a high
quality product.
2. For multi-display installations, the computers require multiple
DVI cards. See Multi-display Installation, page 26, for details.
A VGA, SVGA, XGA, SXGA or multisync card (optional)
Type A USB port
Microphone and speaker ports (optional)
Note: The VGA monitor and VGA card are supported by the CS1768 /
CS1788, but are both optional. Refer to Console Monitor Connection
Options, page 18 for more information on console and computer
equipment installation.
1. Introduction
5
Cables
Only custom USB DVI KVM cable sets, which are specifically designed
to work with this switch, may be used to link to the computers. Two cable
sets are provided with this package.
Note: The quality of the display is affected by the quality and length of the
cables. If you need additional cable sets, please contact your dealer
to purchase the appropriate ones for your switch.
USB DVI-I Single Link for CS1768 / USB DVI-D Dual Link for CS1788
For multi-display installations, standard USB Type A to USB Type B
cables and standard DVI cables are also required.
Type Length Part Number
USB DVI-D Single
Link
1.8 m 2L-7D02U
3.0 m 2L-7D03U
5.0 m 2L-7D05U
USB DVI-I Single
Link
1.8 m 2L-7D02UI
3.0 m 2L-7D03UI
USB DVI-D Dual
Link
1.8 m 2L-7D02UD
3.0 m 2L-7D03UD
5.0 m 2L-7D05UD
CS1768 / CS1788 User Manual
6
Operating Systems
Note: 1. Supports Linux Kernel 2.6 and higher.
2. The CS1768 / CS1788 has a built-in USB 2.0 hub, and does not
support PCs or operating systems that do not support USB 2.0.
OS Version
Windows 2000 / XP / 2003 / 2008 / Vista / 7
Linux RedHat 9.0 and higher
SuSE 10 / 11.1 and higher
Debian 3.1 / 4.0
Ubuntu 7.04 / 7.10
UNIX AIX 4.3 and higher
FreeBSD 5.5 and higher
Sun Solaris 8 and higher
Novell Netware 6.0 and higher
Mac OS 9 to 10.6 (Snow Leopard)
1. Introduction
7
Components
Front View
No. Component Description
1Port Selection
Pushbuttons
For manual port selection (see Port Selection, page 32, also):
Press a port selection pushbutton for longer than two seconds to
bring the KVM, USB hub, and audio focus to the computer attached
to its corresponding port.
Press a pushbutton for less than two seconds to bring the KVM and
audio focus to the computer attached to its corresponding port.
Press push buttons 1 and 2 simultaneously for 2 seconds to start
Auto Scan Mode. See Auto Scan Mode, page 51, for details.
Press push buttons 7 and 8 simultaneously for 2 seconds to perform
a keyboard and mouse reset. See Keyboard / Mouse Reset,
page 53, also
2Port LEDs The Port LEDs are built into the Port Selection Switches. The
upper ones are the KVM Port LEDs; the lower ones are the
USB LEDs:
KVM
Lights DIM ORANGE to indicate that the computer attached to the
corresponding port is up and running (On Line).
Flashes to indicate that Firmware Upgrade mode is in effect.
Changes to BRIGHT ORANGE to indicate that the computer
attached to its corresponding port is the one that has the KVM focus
(Selected).
Flashes to indicate that the computer attached to its corresponding
port is being accessed under Auto Scan mode.
USB
Lights GREEN to indicate that the computer attached to its corre-
sponding port is the one that has access to the USB peripherals.
Note: The USB 2.0 hub cannot be accessed through the
switch by computers on the second or third level of a cascaded
installation.
43
1 & 2
56 7
K/M RESET
CS1768 / CS1788 User Manual
8
3Firmware
Upgrade
Recovery
Switch
During normal operation and while performing a firmware
upgrade, this switch should be in the NORMAL position. If a
firmware upgrade operation does not complete successfully,
this switch is used to perform a firmware upgrade recovery.
See Firmware Upgrade Recovery, page 68, for details.
4Audio Ports The cables from your main speakers and main microphone
plug in here. The speakers and microphone plugged in here
have priority over those in the rear panel.
5USB 2.0 Hub USB 2.0 peripherals (printers, scanners, etc.) can plug into this
port (this may require an extra power adapter).
Note: The USB 2.0 hub cannot be accessed through the
switch by computers on the second or third level of a cascaded
installation.
6Reset Switch Pressing this switch performs a system reset. When the
system is reset, the switch beeps, and the port LEDs flash in
succession until the reset is complete. After the reset is
complete you can login again.
Note: This switch is recessed and must be pushed with a small
object, such as the end of a paper clip or a ballpoint pen.
7Power LED Lights to indicate that the switch is powered up and ready to
operate.
No. Component Description
1. Introduction
9
Rear View
No. Component Description
1Power Jack The power adapter cable plugs in here.
2USB 2.0 Hub USB 2.0 peripherals (printers, scanners, etc.) can plug
into this port (this may require an extra power
adapter).
Note: The USB 2.0 hub cannot be accessed through
the switch by computers on the second or third level of
a cascaded installation.
3Firmware Upgrade
Port
The firmware upgrade cable that transfers the
firmware upgrade data from the administrator's
computer to the CS1768 / CS1788 plugs into this RJ-
11 connector.
4Grounding Terminal The grounding wire used to ground the CS1768 /
CS1788 attaches here.
5Console Port Section The cables from your console DVI and/or VGA
monitor, USB keyboard, USB mouse, speakers, and
microphone plug in here. Each connector is marked
with an appropriate icon to indicate itself.
6KVM Port Sections The cables that link the switch to your computers plug
in here. Each KVM port section is comprised of a
microphone jack, speaker jack(s), USB type B socket
and a DVI-I connector.
4
3
56
12
CS1768 / CS1788 User Manual
10
This Page Intentionally Left Blank
11
Chapter 2
Hardware Setup
Overview
For convenience and flexibility that allows mixing multiple platforms, the
CS1768 / CS1788 design utilizes custom USB DVI KVM cables that serve as
intermediaries between the switch and the connected computers (refer to the
installation diagram on page 17).
A separate custom USB DVI KVM cable is required for each computer
connection. The custom KVM cables are listed under Cables, on page 5.
Consult your dealer to find out which custom KVM cables best fit your needs.
Installation Types
The CS1768 / CS1788 offers two types of installation – 1) standalone/cascade;
and 2) multi-display – that require different cabling setups. Therefore, the
functions of both types are not available in one installation. See the following
sections in this chapter for details about the different cabling requirements.
Before You Begin
1. Important safety information regarding the placement of this
device is provided on page 71. Please review it before
proceeding.
2. To prevent damage to your installation from power surges or
static electricity. It is important that all connected devices are
properly grounded.
3. Make sure that power to all devices that you will be installing
has been turned off. You must unplug the power cords of any
computers that have the Keyboard Power On function.
CS1768 / CS1788 User Manual
12
Stacking and Rack Mounting
The CS1768 / CS1788 can be stacked on the desktop or rack mounted at the
front or rear of the rack. The following sections take you through the
procedures for each method.
Note: 1. Allow at least 5.1 cm on each side for adequate ventilation and
12.7 cm at the rear for power cord and cable clearance.
2. The standard rack mounting kit does not include screws or cage nuts.
If you need additional screws or cage nuts, contact your rack dealer.
Stacking
The CS1768 / CS1788 can be placed on any level surface that can safely
support its weight and the weight of the attached cables. Make sure that the
surface is clean and free of any materials that can block the exhaust vents or
otherwise interfere with normal operation of the switch.
To place the CS1768 / CS1788, or to stack units if you are cascading them,
remove the backing material from the bottom of the rubber feet that came with
this package, and stick them onto the bottom panel at the corners, as shown in
the diagram, below:
2. Hardware Setup
13
Rack Mounting – Front
1. Remove the screws from the left and right sides of the switch (2 screws
total) near the front of the switch.
2. Use the M3 x 8 Phillips hex head screws supplied with the rack mounting kit
to screw the rack mounting brackets into the sides near the front of the unit.
(Continues on next page.)
CS1768 / CS1788 User Manual
14
(Continued from previous page.)
3. Place the KVM switch in the rack. Position it so that the holes in the
mounting brackets line up with the holes in the rack. Secure the mounting
brackets to the front of the rack.
2. Hardware Setup
15
Rack Mounting – Rear
1. Remove 1 screw each from the left and right sides of the switch (2 screws
total) near the rear of the unit.
2. Use the M3 x 8 Phillips hex head screws supplied with the rack mounting kit
to screw the rack mounting brackets into the sides near the rear of the unit.
(Continues on next page.)
CS1768 / CS1788 User Manual
16
(Continued from previous page.)
3. Place the KVM switch in the rack. Position it so that the holes in the
mounting brackets line up with the holes in the rack. Secure the mounting
brackets to the rear of the rack.
2. Hardware Setup
17
Single Stage Installation
To set up your single stage CS1768 / CS1788 installation, refer to the
installation diagram on page 20 (the numbers in the diagrams correspond to the
steps, below), and do the following:
1. Plug your USB keyboard and USB mouse into the USB console ports
located on the unit’s rear panel.
2. Depending on your console monitor’s interface, connect your monitor
using one of the following methods (see Console Monitor Connection
Options, page 18), and power on:
a) One DVI monitor (DVI-I) – plug your DVI console monitor into the
DVI console port located on the unit’s rear panel;
b) One DVI (DVI-D + VGA) monitor – plug your dual-interface console
monitor into both the DVI and VGA console ports;
c) Two Monitors (1 x DVI; 1 x VGA) – plug your DVI monitor into the
DVI console port, and plug your VGA monitor into the VGA console
port.
Note: The CS1768 / CS1788 supports DVI, VGA, and dual interface
monitors, but only one video signal (DVI or VGA) can be displayed
at a time – the signal will display on either the DVI monitor or the
VGA monitor, depending on the OSD settings. See SET
COMPUTER VIDEO INPUT, page 44 for details about setting the
correct video input and output for your video requirements.
3. Plug your main microphone and speakers into the console microphone and
speaker jacks located on the unit’s front panel. The microphone and
speakers plugged into this panel have priority over those in the rear panel.
4. Plug your secondary microphone and speakers into the console audio ports
located on the unit’s rear panel.
5. Using the custom USB DVI KVM cable set provided with this package,
plug the DVI connector into any available DVI socket in the KVM port
section of the switch, then plug the accompanying USB and audio
connectors into their corresponding USB, microphone, and speaker
sockets.
Note: Verify that all the plugs are in the same KVM Port sockets (all in
Port 1, all in Port 2, etc.).
CS1768 / CS1788 User Manual
18
6. At the other end of the cable, plug the USB, video, microphone, and
speaker cables into their respective ports on the computer.
7. Plug your USB peripherals into the type A sockets in the USB hub section.
8. Plug the power adapter that came with your switch into an AC power
source, then plug power adapter cable into the switch’s Power Jack.
9. Power on the computers.
Note: Make sure the computers and devices that the CS1768 / CS1788
connects to are also properly grounded.
Console Monitor Connection Options
2a. One DVI Monitor (DVI-I connector)
2b. One DVI Monitor (DVI-D + VGA connectors)
2a
DVI-I
2b
DVI-D +
VGA
2. Hardware Setup
19
2c. Two Monitors (1 x DVI; 1 x VGA)
DVI
2c
VGA
CS1768 / CS1788 User Manual
20
Single Stage Installation Diagram
1
8
437
7
6
USB DVI
KVM Cable Set
USB DVI
KVM Cable Set
25
VGA
or
DVI
2. Hardware Setup
21
Two Stage Cascade
To control even more computers, additional CS1768 / CS1788 units can be
cascaded from the KVM ports of the First Stage unit. The cascaded CS1768 /
CS1788s that connect back to the First Stage unit are considered Second Stage
units. As many as 64 computers can be controlled in a complete two stage
installation. A table showing the relation between the number of computers and
the number of units needed to control them is provided on page 75.
To set up a two stage installation, refer to the Two Stage Installation diagram
on the next page as you do the following:
1. Make sure that power to all the devices you will be connecting up,
including all preexisting devices on the installation, have been turned off.
2. Use a custom USB DVI KVM cable set (see Cables, page 5) to connect
any available KVM Port on the First Stage unit to the Console ports of the
Second Stage unit.
Note: Plug the USB Type B connector into the upper USB port in the
Console section (they are both marked with a similar icon to remind
you of the correct USB port).
3. Using another custom USB DVI KVM cable set (provided with this
package), plug the DVI connector into any available DVI socket in the
KVM port section of the switch, then plug the accompanying USB Type
A, microphone and speaker connectors into their corresponding USB,
microphone, and speaker sockets.
Note: Verify that all the plugs are in the same KVM Port sockets (all in
Port 1, all in Port 2, etc.), and that each socket is marked with an
appropriate icon to indicate itself.
4. At the other end of the cable, plug the USB Type B, video, microphone,
and speaker cables into their respective ports on the computer.
5. Repeat steps 3 and 4 for any other computers you are connecting up.
6. For each Second Stage unit, plug the power adapter cable into its Power
Jack, then plug the power adapter into an AC source.
7. Plug the First Stage unit's power adapter cable into its Power Jack, then
plug the power adapter into an AC source.
(Continues on next page.)
CS1768 / CS1788 User Manual
22
8. Power on the computers.
Note:The Power On sequence requires that all Second Stage units be
powered on first. After they are all on, the First Stage units must
be powered on next. Only after all the switches have been
powered on in this sequence, can the computers be powered on.
The USB2.0 hub cannot be accessed through the switch by
computers on the second or third level of a cascaded installation.
Make sure the computers and devices that the CS1768 / CS1788
connects to are also properly grounded.
2. Hardware Setup
23
Two Stage Installation Diagram
USB DVI
KVM Cable Set
CS1768 / CS1788 User Manual
24
Three Stage Cascade
The procedures for setting up a three stage installation are essentially the same
as for a two stage installation. With a three stage setup, as many as 512
computers can be controlled in a complete installation. A table showing the
relation between the number of computers and the number of switches needed
to control them is provided on page 75.
Once you have finished cabling up (see Two Stage Cascade, page 21 if
necessary), power up according to the following sequence:
1. For each Third Stage unit, plug the power adapter cable into the switch's
Power Jack; plug the power adapter into an AC source.
2. For each Second Stage unit, plug the power adapter cable into the switch's
Power Jack; plug the power adapter into an AC source.
3. Plug the First Stage unit's power adapter cable into its Power Jack, then
plug the power adapter into an AC source.
4. Power on the computers.
Note:The Power On sequence requires that all Third Stage units be
powered on first. After they are all on, the Second Stage units
must be powered on next. After the Second Stage units are on, the
First Stage units must be powered on last. Only after all the
switches have been powered on in this sequence, can the
computers be powered on.
The USB 2.0 hub cannot be accessed through the switch by
computers on the second or third level of a cascaded installation.
Make sure the computers and devices that the CS1768 / CS1788
connects to are also properly grounded.
2. Hardware Setup
25
Three Stage Installation Diagram
USB DVI
KVM Cable Set
USB DVI
KVM Cable Set
CS1768 / CS1788 User Manual
26
Multi-display Installation
The CS1768 / CS1788’s multi-display feature allows you to stack two, three or
four units in a dual/triple/quad-display installation to control up to seven
computers at once. This installation requires different cabling than the standard
cascade and offers an extra level of switching flexibility for multiple-monitor
installations where each computer is fitted with multiple video cards.
Cable Connections for Multi-display Installation
To set up your multi-display installation, refer to the installation diagram on the
next page (the numbers in the diagrams correspond to the steps, below), and do
the following:
1. Use a standard USB Type A-to-USB Type B cable to connect the Port 8
USB Type A port on the first stage unit to the USB Type B port in the
Console section of the second switch.
Note: Port 8 is reserved to connect the units in a multi-display installation,
so up to seven computers can be attached, using KVM ports 1–7.
2. Use DVI cables to connect the DVI KVM port on the second CS1768 /
CS1788 unit to the second video-in port on the computers.
Note: Only DVI video cables are necessary – the other ports in the KVM
section are not required in this installation.
3. Connect a display to the console section of the second switch.
4. Repeat steps 1–3 for any additional units, up to a total of four switches.
5. Connect the cables for the first switch. See Single Stage Installation,
page 17 for full details. All video, audio and peripheral devices must be
connected to the first switch.
6. Power up the CS1768 / CS1788 units, starting with the first switch, and
then power on the computers.
Note: Make sure the computers and devices that the CS1768 / CS1788
connects to are also properly grounded.
2. Hardware Setup
27
Multi-display Installation Diagram
5
51
5
2
3
Computers with
2/3/4 video inputs
USB Type A to
Type B cables
DVI cables
Third / Fourth
Stage Units
4
Second Switch
First Switch
CS1768 / CS1788 User Manual
28
Grouping Ports into “Vertical” Channels
Once the cables have been connected and multi-display mode has been selected
in the OSD, the CS1768 / CS1788 auto-detects the channels and viewing
modes.Users can then assign them a channel number as the port name (the
channels are represented by the vertical columns in the diagram below). So, all
the Port 1s become Channel 1, all the Port 2s become Channel 2, ... , and all the
Port 7s become Channel 7. The ports will all be switched at the same time,
channel by channel.
Depending on the number of stages in your stack, a CS1768 / CS1788
installation offers dual display (two stages), triple display (three stages) and
quad display (four stages) scenarios. For reference purposes, the example
shows a four-stage installation with quad display functionality.
Note: Only one video signal (DVI or VGA) can be displayed at a time,
depending on the configuration of the CS1768 / CS1788 unit on the first
switch.
2. Hardware Setup
29
Channels Diagram
Ch7 Ch6 Ch1
First
Switch
Second
Switch
Third
Switch
Fourth
Switch
CS1768 / CS1788 User Manual
30
This Page Intentionally Left Blank
31
Chapter 3
Basic Operation
Hot Plugging
The CS1768 / CS1788 supports hot plugging – components can be removed
and added back into the installation by unplugging their cables from the ports
without the need to shut the unit down. In order for hot plugging to work
properly, the procedures described below must be followed:
Hot Plugging KVM Ports
In order for the OSD menus to correspond to KVM port changes, you must
manually reconfigure the OSD to reflect the new port information. See the F3
SET (page 39) and F4 ADM (page 41), functions for details.
Note: If the computer's operating system does not support hot plugging, this
function may not work properly.
Hot Plugging Console Ports
The keyboard, monitor, and mouse can all be hot plugged. When hot plugging
the mouse:
You may unplug and replug the mouse (to reset the mouse, for example),
as long as you use the same mouse.
If you plug in a different mouse, all the computers on the installation must
be shut down for 10 seconds, then restarted following the power up
sequence described under Steps 6, 7, and 8 under Two Stage Cascade,
page 21
Note: If, after hot plugging there is no response to keyboard and/or mouse
input, perform a Keyboard and Mouse Reset by simultaneously
pressing the 1 and 2 front panel port LEDs.
CS1768 / CS1788 User Manual
32
Port Selection
The CS1768 / CS1788 provides three port selection methods to access the
computers on the installation: Manual, an OSD (on-screen display) menu
system, and Hotkeys. See Chapter 4, OSD Operation and Chapter 5, Hotkey
Operation for more information.
Manual Port Switching
Use the front panel pushbutton switches to manually switch to a port.
Port ID Numbering
Each port on a CS1768 / CS1788 installation is assigned a unique Port ID. You
can directly access any computer on any level of the installation by specifying
the Port ID that the computer is connected to – either with the OSD (see OSD
Operation, page 35), or with the Hotkey port selection method (see Hotkey
Operation, page 49).
A computer attached to a master unit has a two digit Port ID (from 01–08
for the CS1768 / CS1788) that corresponds to the KVM port number that it
is connected to.
A computer attached to a slave unit has a four digit Port ID.
The first two digits represent the KVM port number on the master and the
second two digits represent the KVM port number on the slave unit that
the computer is connected to. For example, a Port ID of 02–08 would refer
to a computer that is connected to KVM port 8 of a slave unit that links
back to KVM port 2 of the master unit.
3. Basic Operation
33
Powering Off and Restarting
If it becomes necessary to power off a CS1768 / CS1788, do the following
before restarting it:
1. Unplug the CS1768 / CS1788 from its power source.
2. Shut down all the computers that are attached to it.
Note: Unplug the power cords of any computers that have the Keyboard
Power On function. Otherwise, the CS1768 / CS1788 will still
receive power from the computers.
3. Wait 10 seconds, then plug the CS1768 / CS1788 back in.
4. Power on the computers.
Note: If there are stations cascaded down from the master CS1768 / CS1788,
all the cascaded stations and the computers attached to them must be
shut down as well.
CS1768 / CS1788 User Manual
34
This Page Intentionally Left Blank
35
Chapter 4
OSD Operation
OSD Overview
The on-screen display (OSD) is a mouse and keyboard enabled, menu driven
method to handle computer control and switching operations. All procedures
start from the OSD main screen.
Manufacturing Number
The “MFG Number” (Manufacturing Number) is an internal serial number
used by ATEN’s factory and technical support staff to identify products. This
number does not affect products’ warranty. If your product requires after-sales
services, you may provide the MFG Number to ATEN’s sales or technical
support staff to identify the product and model number.
OSD Login
The OSD incorporates a two level (administrator / user) password system.
Before the OSD main screen displays, a login screen appears requiring a
password. If this is the first time that the OSD is used, or if the password
function has not been set, simply press [Enter]. The OSD main screen displays
in administrator mode. In this mode, you have administrator privileges, with
access to all administrator and user functions, and can set up operations
(including password authorization) as you like. If the password function has
been set, you must provide an appropriate administrator/user password in order
to access the OSD.
OSD Hotkey
You can display the OSD on the console monitor while also viewing the
display of any port on the CS1768 / CS1788 by pressing the [Scroll Lock] key
twice.
Note: You can optionally change the OSD hotkey to the Ctrl key, in which
case you would press [Ctrl] twice (see OSD Hotkey, page 39). With this
method, you must press the same [Ctrl] key.
CS1768 / CS1788 User Manual
36
OSD Main Screen
When you invoke the OSD, a screen similar to the one below appears:
Note: 1. The diagram depicts the administrator's main screen. The user main
screen does not show the F4 and F6 functions, since these are
reserved for the administrator and can't be accessed by users.
2. The OSD always starts in list view, with the highlight bar at the same
position it was in the last time it was closed.
3. Only the ports that have been set accessible by the administrator for
the current logged in user are visible (see SET ACCESSIBLE PORTS,
page 41, for details).
4. If the port list is collapsed, click on a switch number, or move the
highlight bar to it then press the right arrow key to expand the list.
Similarly, to collapse a switch’s port list, click on the switch number,
or move the highlight bar to it then press the left arrow key to collapse
the list.
OSD Main Screen Headings
PN This column lists the port ID numbers for all the KVM ports on the
installation. The simplest method to access a particular computer is
move the highlight bar to it, then press Enter.
QV If a port has selected for quick view scanning (see Set Quick View Ports,
page 43), an arrowhead displays in this column.
The computers that are powered on and are online have a sun symbol
in this column.
NAME If a port has been given a name (see Edit Port Names, page 42), its
name appears in this column.
4. OSD Operation
37
OSD Navigation
To dismiss the menu, and deactivate OSD, click the X at the upper right
corner of the OSD window; or press [Esc].
To log out, click F8 at the top of the main screen, or press [F8].
To move up or down through the list one line at a time, click the up and
down triangle symbols (ST) or use the up and down arrow keys. If there
are more list entries than what can appear on the main screen, the screen
will scroll.
To move up or down through the list one screen at a time, click the up and
down arrow symbols (), or use the [Pg Up] and [Pg Dn] keys. If there
are more list entries than what can appear on the main screen, the screen
will scroll.
To activate a port, double-click it, or move the highlight bar to it then press
[Enter].
After executing any action, you automatically go back to the menu one
level above.
OSD Functions
OSD functions are used to configure and control the OSD. For example, you
can rapidly switch to any port, scan selected ports, limit the list you wish to
view, designate a port as a quick view port, create or edit a port name, or make
OSD setting adjustments.
To access an OSD function:
1. Either click a function key field at the top of the main screen, or press a
function key on the keyboard.
2. In the submenus that appear make your choice either by double-clicking it,
or moving the highlight bar to it, then pressing [Enter].
3. Press [Esc] to return to the previous menu level.
CS1768 / CS1788 User Manual
38
F1: GOTO
Clicking the F1 field or pressing [F1] activates the GOTO function. GOTO
allows you to switch directly to a port either by keying in the port's Name, or
its Port ID.
To use the name method, key in 1; key in the port's Name; then press
[Enter] to switch KVM, Audio and USB focus; or [Spacebar] to switch
KVM and Audio only.
To use the port ID method, key in 2; key in the Port ID; then press [Enter]
to switch KVM, Audio and USB focus; or [Spacebar] to switch KVM and
Audio only.
Note: You can key in a partial name or port ID. In that case, the screen will
show all the computers that the user has View rights to (see SET
ACCESSIBLE PORTS, page 41), that match the name or port ID
pattern, regardless of the current list settings (see F2 LIST, page 38, for
details).
To return to the OSD main screen without making a choice, press [Esc].
F2: LIST
This function lets you broaden or narrow the scope of which ports the OSD
displays on the main screen. The submenu choices and their meanings are
given in the table below.
Move the highlight bar to the choice you want, then press [Enter]. An icon
appears before the choice to indicate that it is the currently selected one.
Choice Meaning
ALL Lists all of the ports on the installation that have been set accessible
by the administrator for the current logged in user.
QUICK VIEW Lists only the ports that have been selected as quick view ports (see
SET QUICK VIEW PORTS, page 43).
POWERED ON Lists only the ports that have their attached computers powered on.
QUICK VIEW +
POWERED ON
Lists only the ports that have been selected as quick view ports (see
SET QUICK VIEW PORTS, page 43), and that have their attached
computers powered on.
4. OSD Operation
39
F3: SET
This function allows the administrator and each user to set up his own working
environment. A separate profile for each is stored by the OSD and is activated
according to the username that was provided during login.
To change a setting:
1. Double-click it; or move the highlight bar to it, then press [Enter].
2. After you select an item, a submenu with further choices appears. To make
a selection, either double-click it; or move the highlight bar to it, then
press [Enter]. An icon appears before the selected choice to indicate
which one it is. The settings are explained in the following table:
(Continues on next page.)
Setting Function
OSD HOTKEY Selects which hotkey activates the OSD function:
[Scroll Lock] [Scroll Lock] or [Ctrl] [Ctrl].
Since the [Ctrl] key combination may conflict with programs running
on the computers, the default is the [Scroll Lock] combination.
PORT ID
DISPLAY
POSITION
Allows each user to customize the position where the port ID
appears on the screen. The default is the upper left corner, but
users can choose to have it appear anywhere on the screen.
Use the mouse or the arrow keys plus Pg Up, Pg Dn, Home, End,
and 5 (on the numeric keypad with Num Lock off), to position the
port ID display, then double-click or press [Enter] to lock the
position and return to the Set submenu.
PORT ID
DISPLAY
DURATION
Determines how long a port ID displays on the monitor after a port
change has taken place. The choices are: 3 Seconds and Always
Off.
PORT ID
DISPLAY
MODE
Selects how the port ID is displayed: the port number plus the port
name (PORT NUMBER + PORT NAME) (default); the port number
alone (PORT NUMBER); or the port name alone (PORT NAME).
SCAN
DURATION
Determines how long the focus dwells on each port as it cycles
through the selected ports in Auto Scan mode (see F7 SCAN,
page 46). Key in a value from 1–255 seconds, then press [Enter].
Default is 5 seconds; a setting of 0 disables the SCAN function.
CS1768 / CS1788 User Manual
40
(Continued from previous page.)
Setting Function
SCAN–SKIP
MODE
Selects which computers will be accessed under skip mode (see
F5 SKP, page 45), and Auto Scan mode (see F7 SCAN, page 46.
Choices are:
ALL - All the ports which have been set accessible (see SET
ACCESSIBLE PORTS, page 41);
QUICK VIEW - Only those ports which have been set accessible
and have been selected as quick view ports (see SET QUICK
VIEW PORTS, page 43);
POWERED ON - Only those ports which have been set accessible
and are powered on;
QUICK VIEW + POWERED ON - Only those ports which have
been set accessible and have been selected as quick view ports
and are powered on. The default is ALL.
Note: The quick view choices only show up on the administrator's
screen, since only he has Quick View setting rights (see SET
QUICK VIEW PORTS, page 43, for details).
SCREEN
BLANKER
If there is no input from the console for the amount of time set with
this function, the screen is blanked. Key in a value from 1–30
minutes, then press [Enter]. The default setting of 0 disables this
function.
HOTKEY
COMMAND
MODE
Enables / disables the hotkey command function in case a conflict
with programs running on the computers occurs.
HOTKEY Sets the keyboard shortcut for invoking Hotkey Mode (see
page 49). Choices are: NUM LOCK + - (minus) (default), and
CTRL + F12.
OSD
LANGUAGE
Sets the language used in the OSD. Choices are: English (default),
German, Japanese, Simplified Chinese and Traditional Chinese,
Spanish, French, and Russian.
4. OSD Operation
41
F4: ADM
F4 is an administrator only function. It allows the administrator to configure
and control the overall operation of the OSD. To change a setting double-click
it, or use the up and down arrow keys to move the highlight bar to it then press
[Enter].
After you select an item, a submenu with further choices to select from appears.
Double-click an item, or move the highlight bar to it then press [Enter]. An
icon appears before the selected item so that you know which one it is. The
settings are explained in the following table:
(Continues on next page.)
Setting Function
SET USER
LOGIN
This function is used to set usernames and passwords for the
administrator and users:
1. Usernames and passwords for one administrator and four users
can be set.
2. After you select the administrator field or one of the user fields,
a screen that allows you to key in the username and password
appears. Usernames and passwords can be from 1 to 16
characters long and can consist of any combination of letters
and numbers (A–Z, 0–9) and some additional keys (* ( ) + : - , ?
. / space).
3. For each individual, key in the username and password, confirm
the password, then press [Enter].
4. To modify or delete a previous username and/or password, use
the backspace key to erase individual letters or numbers. Press
[Enter] when done.
Note: Usernames and passwords are not case sensitive.
Usernames are displayed in capital letters in the OSD.
SET
ACCESSIBLE
PORTS
This function allows the administrator to define user access to the
computers on the installation on a port-by-port basis.
For each user, select the target port; then press the [Spacebar] to
cycle through the choices: F (full access), V (view only), or blank.
Repeat until all access rights have been set, then press [Enter].
The default is F for all users on all ports.
Note:
A blank setting means that no access rights are granted. The
port will not show up on the user's LIST on the main screen.
The administrator always has full access to all ports.
CS1768 / CS1788 User Manual
42
(Continued from previous page.)
(Continues on next page.)
Setting Function
SET LOGOUT
TIMEOUT
If there is no input from the console for the amount of time set with
this function, the user is automatically logged out. A login is
necessary before the console can be used again.
This enables other users to gain access to the computers when the
original user is no longer accessing them, but has forgotten to log
out. To set the timeout value, key in a number from 1–180 minutes,
then press [Enter]. The default setting of 0 disables this function.
Note: This feature does not function if Set Login Mode is disabled.
See SET LOGIN MODE, page 44.
EDIT PORT
NAMES
To help remember which computer is attached to a particular port,
every port can be given a name. This function allows the
administrator to create, modify, or delete port names.
To edit a port name:
1. Click the port, or use the navigation keys to move the highlight
bar to it, then press [Enter].
2. Key in the new port name, or modify/delete the old one. The
maximum number of characters allowed for the port name is 12.
Legal characters include:
All alpha characters: A–Z
All numeric characters: 0–9
* ( ) + : - , ? . /
Case does not matter; the OSD displays the port name in all
capitals no matter how they were keyed in.
3. When you have finished editing, press [Enter] to have the
change take effect. To abort the change, press [Esc].
RESTORE
DEFAULT
VALUES
This function is used to undo all changes and return the setup to
the original factory default settings (See Factory Default Hotkeys
and Settings, page 79) except for the port name list, username and
password information, which are saved.
CLEAR THE
NAME LIST
This function clears the port name list.
ACTIVATE
BEEPER
Choices are Y (on), or N (off). When activated, the beeper sounds
whenever a port is changed; when activating the Auto Scan
function (see F7 SCAN, page 46); or an invalid entry is made on an
OSD menu. The default is Y.
4. OSD Operation
43
(Continued from previous page.)
(Continues on next page.)
Setting Function
SET QUICK
VIEW PORTS
This function lets the administrator select which ports to include as
quick view ports.
To select/deselect a port as a quick view port, double-click the
port, or use the navigation keys to move the highlight bar to it,
then press [Spacebar].
When a port has been selected as a quick view port, an icon dis-
plays in the QV column of the LIST on the main screen. When a
port is deselected, the icon disappears.
If one of the quick view options is chosen for the LIST view (see
F2 LIST, page 38), only a port that has been selected here
will display on the list.
If one of the quick view options is chosen for auto-scanning
(see SCAN/SKIP MODE, page 40), only a port that has been
selected here will be auto-scanned.
The default has no ports selected for quick view.
SET
OPERATING
SYSTEM
This function allows the administrator to define the operating
system for the computer connected to each KVM port. The default
is WIN (PC compatible).
To set the port operating system:
1. From the list, select the port for which you wish to set the com-
puter's operating system.
2. Set the operating system by pressing [Spacebar] to cycle
through WIN, MAC, SUN, or OTHER .
3. Press [Esc] to exit. The operating system you selected is
assigned to the KVM port.
FIRMWARE
UPGRADE
In order to upgrade the CS1768 / CS1788 firmware (see page 63),
you must first enable Firmware Upgrade mode with this setting.
When you bring up this menu, the current firmware version levels
are displayed. Select Y to enable Firmware Upgrade mode, or N to
leave this menu without enabling it.
KEYBOARD
LANGUAGE
Sets the language for the computer keyboard attached to the KVM
port. To select a keyboard language, double-click it, or use the
navigation keys to move the highlight bar to it, then press [Enter].
Choices are: AUTO (default), ENGLISH (US), ENGLISH (UK),
GERMAN (GER.), GERMAN (SWISS), FRENCH, HUNGARIAN,
ITALIAN, JAPANESE, KOREAN, RUSSIAN, SPANISH, SWEDISH,
TRADITIONAL CHINESE, and SIMPLIFIED CHINESE.
CS1768 / CS1788 User Manual
44
(Continued from previous page.)
Setting Function
SET
COMPUTER
VIDEO INPUT
Sets the video signal for each KVM port for the computers attached
to the CS1768 / CS1788.
Options are:
DVI-A
DVI-D
SET CONSOLE
VIDEO OUTPUT
Sets the console video output. If the computer attached to the
CS1768 / CS1788 is VGA output, this can be set to display on
either the VGA or the DVI console monitor.
Options are:
DVI-A to VGA – select this option if you have one DVI monitor
with a DVI-D plus VGA connector, or if you have two monitors (1
x DVI, 1 x VGA)
DVI-A to DVI-I – select this option if you have one DVI monitor
with a DVI-I connector
Note: In a cascade installation or if you are using a VGA-to-DVI
adapter in your installation, select DVI-A to DVI-I
MOUSE
EMULATION
Enables / disable mouse emulation function.
Note: Supported in the first level of an installation only.
ACTIVATE Multi-
display
Enables multi-display mode for dual, triple or quad display in
multiple-monitor installations where each computer is fitted with
multiple video cards. See Multi-display Installation, page 26, for full
details.
Note: The multi-display mode must be enabled on the OSD before
the cables are connected.
OSD CONFIG
BACKUP /
RESTORE
Enters OSD Configuration Backup / Restore mode. The Firmware
Management Utility lets you backup the current OSD configuration
of the CS1768 / CS1788, and restore it when necessary. Storing the
OSD configuration settings is useful when deploying more than one
installation that uses the same settings. See OSD Configuration
Backup/Restore, page 69, for full details.
SET LOGIN
MODE
This function allows the administrator to request users to login or
not. When the login dialog box is disabled, the system disables the
login/logout function. If the system is re-started, the login/logout
function remains disabled.
4. OSD Operation
45
F5: SKP
Clicking the F5 field or pressing [F5] invokes Skip (SKP) mode. This function
enables you to easily skip backward or forward – switching the console focus
from the currently active computer port to the previous or next accessible one.
The selection of computers available for skip mode switching is made with
the Scan–Skip mode setting under the F3: SET function (see page 39).
When you are in skip mode:
press [
←
] to skip to the previous accessible port on the list
press [
→ ]
to skip to the next accessible port on the list
press [
↑
] to skip to the next accessible port. If the next accessible port has
cascaded a switch, then it skips to the first accessible port of that switch
press [
↓
] to skip to the previous accessible port. If the previous accessible
port has cascaded a switch, then it skips to the last accessible port of that
switch
Note: When you skip, you only skip to the previous or next accessible
computer that is in the Scan–Skip mode selection (page 40).
If a port has been selected for Scan–Skip mode, when the focus switches to
that port a left/right triangle symbol appears before its port ID display.
When the port ID with the triangle symbol displays, the background screen
is blank.
While skip mode is in effect, the console will not function normally. You
must exit skip mode in order to regain control of the console.
When the selected port displays, skip mode is automatically disabled.
To exit skip mode, press [Spacebar] or [Esc].
F6: BRC
F6 is an administrator only function. Clicking the F6 field, or pressing [F6],
invokes Broadcast (BRC) mode. When this function is in effect, commands
sent from the console are broadcast to to all available computers on the
installation.
This function is particularly useful for operations that need to be performed on
multiple computers, such as performing a system wide shutdown, installing or
upgrading software, etc.
CS1768 / CS1788 User Manual
46
While BRC mode is in effect, a speaker symbol appears before the port ID
display of the port that currently has the console focus. When the port ID
with the speaker symbol displays, the background screen is blank.
While BRC mode is in effect, the mouse will not function normally. You
must exit BRC mode in order to regain control of the mouse.
To exit BRC mode, invoke the OSD (with the OSD hotkey), then click the
F6 field, or press [F6], to turn BRC mode off.
When BRC mode is in effect, the Scroll Lock LED flashes. It stops
flashing and reverts to normal status when you exit BRC.
F7: SCAN
Clicking the F7 field or pressing [F7] invokes Auto Scan mode. This function
allows you to automatically switch among the available computers at regular
intervals so that you can monitor their activity without having to take the
trouble of switching yourself.
The selection of computers to be included for auto-scanning is made with
the Scan–Skip mode setting under the F3: SET function (see page 40).
The amount of time that each port displays for is set with the Scan
Duration setting under the F3: SET function (see page 39). When you
want to stop at a particular location, press the [Spacebar] to stop scanning.
If the scanning stops on an empty port, or one where the computer is
attached but is powered Off, the monitor screen will be blank, and the
mouse and keyboard will have no effect. After the Scan Duration time is
up, the scan function will move on to the next port.
As each computer is accessed, an S appears in front of the port ID display
to indicate that it is being accessed under Auto Scan mode. When the port
ID with the symbol displays, the background screen is blank.
While Auto Scan mode is in effect, the console will not function normally.
You must exit Auto Scan mode in order to regain control of the console.
While you are in Auto Scan mode, you can pause the scanning in order to
keep the focus on a particular computer either by pressing P, or with a left-
click of the mouse. See Invoking Auto Scan, page 51, for details.
To exit Auto Scan mode, press the [Spacebar] or [Esc].
4. OSD Operation
47
F8: LOUT
Clicking the F8 field, or pressing [F8] logs you out of OSD control of the
computers, and blanks the console screen. This is different from simply
pressing [Esc] when you are at the main screen to deactivate the OSD. With
this function you must log in all over again to regain access to the OSD,
whereas with [Esc], all you have to do to reenter the OSD is tap the OSD
hotkey.
Note: 1. When you reenter the OSD after logging out, the screen stays blank
except for the OSD main screen. You must input your username and
password before you can continue.
2. If you reenter the OSD after logging out, and immediately use [Esc]
to deactivate the OSD without having selected a port from the OSD
menu, a null port message displays on the screen. The OSD hotkey
will bring up the main OSD screen.
CS1768 / CS1788 User Manual
48
This Page Intentionally Left Blank
49
Chapter 5
Hotkey Operation
Hotkey Port Control
Hotkey port control allows you to provide KVM focus to a particular computer
directly from the keyboard. The CS1768 / CS1788 provides the following
hotkey port control features:
Selecting the Active Port
Auto Scan Mode Switching
Skip Mode Switching
Computer Keyboard / Mouse Reset
Enable / Disable Mouse Emulation
The following settings can also be controlled in Hotkey mode:
Setting the Beeper
Setting the Quick Hotkey
Setting the OSD Hotkey
Setting the Port Operating System
Restoring the OSD Default Values
Invoke Hotkey Mode
All hotkey operations begin by invoking Hotkey mode. There are two possible
keystroke sequences used to invoke Hotkey mode, though only one can be
operational at any given time:
Number Lock and Minus Keys
1. Hold down the Num Lock key;
2. Press and release the minus key;
3. Release the Num Lock key:
[Num Lock] + [-]
CS1768 / CS1788 User Manual
50
Control and F12 Keys
1. Hold down the Ctrl key;
2. Press and release the F12 key;
3. Release the Ctrl key:
[Ctrl] + [F12]
When Hotkey mode is active:
A command line appears on the monitor screen. The command line prompt
is the word Hotkey: in white text on a blue background, and displays the
subsequent hotkey information that you key in.
Ordinary keyboard and mouse functions are suspended – only hotkey
compliant keystrokes (described in the sections that follow), can be input.
Pressing [Esc] exits Hotkey mode.
Select the Active Port
Each KVM port is assigned a port ID (see Port ID Numbering, page 32). You
can directly access any computer on the installation with a hotkey combination
that specifies the port ID of the KVM port that a computer is connected to. To
access a computer using hotkeys:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Key in the port ID.
The port ID numbers display on the command line as you key them in. If
you make a mistake, use [Backspace] to erase the wrong number.
3. Press [Enter].
After you press [Enter], the KVM focus switches to the designated
computer and you automatically exit hotkey mode.
Note: In hotkey mode, KVM focus will not switch to a port if an invalid
switch or port number is entered. The hotkey command line will
continue to display on the screen until you enter a valid switch and
port number combination, or exit hotkey mode.
5. Hotkey Operation
51
Auto Scan Mode
Auto Scan automatically switches, at regular intervals, among all the KVM
ports that have been set as accessible under Scan–Skip Mode, so that their
activity can be monitored automatically. See Scan–Skip Mode on page 40 for
more information.
Invoking Auto Scan:
To start Auto Scan, key in the following Hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Press [A]. After you press A, then [Enter], you automatically exit hotkey
mode, and enter Auto Scan mode.
While you are in Auto Scan mode, you can pause the scanning in order
to keep the focus on a particular computer either by pressing P or with
a left click of the mouse. During the time that auto-scanning is paused,
the command line displays: Auto Scan: Paused.
Pausing when you want to keep the focus on a particular computer is
more convenient than exiting Auto Scan mode because when you
resume scanning, you start from where you left off. If, on the other
hand, you exited and restarted, scanning would start over from the very
first computer on the installation.
To resume Auto Scanning, press any key or left-click. Scanning
continues from where it left off.
While Auto Scan mode is in effect, ordinary keyboard and mouse
functions are suspended – only Auto Scan mode compliant keystrokes
and mouse clicks can be input. You must exit Auto Scan mode in order
to regain normal control of the console.
3. To exit Auto Scan mode press [Esc] or [Spacebar]. Auto-scanning stops
when you exit Auto Scan mode.
CS1768 / CS1788 User Manual
52
Skip Mode
This feature allows you to switch between computers in order to monitor them
manually. You can dwell on a particular port for as long as you like – as
opposed to auto-scanning, which automatically switches after a fixed interval.
To invoke Skip mode, key in the following hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Key in [Arrow]
Where [Arrow] refers to one of the arrow keys. After you press an
arrow, you automatically exit hotkey mode and enter Skip mode where
you can switch ports as follows:
Once you are in Skip mode, you can keep on skipping by pressing the
arrow keys. You don't have to use the [Num Lock] + [-] combination
again.
While Skip mode is in effect, ordinary keyboard and mouse functions
are suspended – only Skip mode compliant keystrokes can be input.
You must exit Skip mode in order to regain normal control of the
console.
3. To exit Skip mode, press [Esc] or [Spacebar].
←Skips to the previous accessible port. (See Scan/Skip Mode,
page 40, for information regarding accessible ports.)
→Skips to the next accessible port.
↑Skips to the previous accessible port. If the previous accessible
port has cascaded a switch, then it skips to the last accessible
port of that switch.
↓Skips to the next accessible port. If the next accessible port has
cascaded a switch, then it skips to the first accessible port of that
switch.
5. Hotkey Operation
53
Keyboard / Mouse Reset
If the keyboard or mouse cease to function on the computer connected to the
currently selected port, you can perform a keyboard / mouse reset on the
computer. This function is essentially the same as unplugging and replugging
the keyboard and mouse on the target computer. To perform a computer
keyboard / mouse reset, key in the following hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Press [F5].
After you press [F5] you automatically exit Hotkey mode and regain keyboard
and mouse control on the computer connected to the KVM port. If you fail to
regain keyboard / mouse control on the computer after pressing [F5], perform
a console keyboard and mouse reset. For more information see Port LEDs,
page 7.
Hotkey Beeper Control
The beeper (see Activate Beeper, page 42) can be hotkey toggled on and off.
To toggle the beeper, key in the following hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Press [B].
After you press [B], the beeper toggles on or off. The command line displays
Beeper On or Beeper Off for one second; then the message disappears and you
automatically exit hotkey mode.
CS1768 / CS1788 User Manual
54
Quick Hotkey Control
The Quick Hotkey (see HOTKEY, page 40) can be toggled between
[Num Lock] + [-], and [Ctrl] + [F12]. To toggle the Quick Hotkey:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Press [H].
After you press [H], the command line displays HOTKEY HAS BEEN
CHANGED for one second; then the message disappears and you
automatically exit Hotkey mode.
OSD Hotkey Control
The OSD Hotkey (see OSD HOTKEY, page 39) can be toggled between [Scroll
Lock], [Scroll Lock] and [Ctrl], [Ctrl]. To toggle the OSD Hotkey, key in the
following hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Press [T].
After you press [T], the command line displays HOTKEY HAS BEEN
CHANGED for one second; then the message disappears and you
automatically exit Hotkey mode.
5. Hotkey Operation
55
Port OS Control
A port’s operating system can be changed to match that of the computer
attached to the port. To change a port’s operating system, key in the following
hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Key in [Function], where [Function] refers to one of the function keys in
the following table:
After pressing a function key you automatically exit Hotkey mode.
Set USB Speed
Users can use hotkeys to set the USB speed of the selected KVM port to low/
full speed to comply with the connected computers.
1. Invoke Hotkey mode (see Invoke Hotkey Mode on page 49).
2. Press [F11]
3. Key in [Function], where [Function] refers to one of the function keys in
the following table:
4. Press [Enter].
To set all KVM ports of the selected KVM station, add an [A] after the function
key: Under Hotkey mode, press [F11][L][A][Enter] or [F11][F][A][Enter].
Key Description
F1 Sets the Port OS to Windows
F2 Sets the Port OS to Mac
F3 Sets the Port OS to Sun
Key Description
L Set the KVM port to low speed USB
F Set the KVM port to full speed USB
CS1768 / CS1788 User Manual
56
Restore Default Values
This administrator only hotkey restores the CS1768 / CS1788 default values.
See RESTORE DEFAULT VALUES on page 42. To restore the default
values, key in the following hotkey combination:
1. Invoke hotkey mode with the [Num Lock] + [-] or [Ctrl] + [F12]
combination.
2. Press [R].
3. Press [Enter].
After you press [Enter], the command line displays RESET TO DEFAULT
SETTING for three seconds; then the message disappears and you
automatically exit Hotkey mode.
USB Reset
If the USB loses focus and needs to be reset, do the following:
1. Invoke HSM (see page 49).
2. Press and release [F5].
Hotkey Buzzer Control
The Buzzer can be enabled or disabled. The default setting is enabled. To
disable the Buzzer, do the following:
1. Invoke HSM (see page 49
).
2. Press and release [B].
This procedure is a toggle. Repeat to enable.
Restore Default Settings
To reset the CS1768 / CS1788 to its default hotkey settings, do the following:
1. Invoke HSM (see page 49).
2. Press [R] [Enter].
See Factory Default Hotkeys and Settings, page 79
5. Hotkey Operation
57
Video DynaSync
Video DynaSync is ATEN’s exclusive technology that eliminates boot-up
display problems and optimizes resolution when switching between ports. To
invoke Video DynaSync, do the following:
1. Invoke HSM (see page 49)
2. Press [D].
Note: If the monitor is disconnected and reconnected, the CS1768 /
CS1788 re-executes Video DynaSync.
Mouse Emulation Control
The default setting is enabled. To disable, do the following:
1. Invoke HSM (see page 49
).
2. Press [M].
This procedure is a toggle. Repeat to enable.
CS1768 / CS1788 User Manual
58
HSM Summary Table
After invoking HSM (see page 49), key in one of the following keys to perform
the corresponding function:
Key Function
[PN] [Enter] Switches KVM, Audio, and USB focus directly to the computer that
corresponds to that port ID. (PN = port number)
[PN] [K] [Enter] Switches KVM focus only directly to the computer that corresponds
to that port ID. (PN = port number)
[PN] [U] [Enter] Switches USB focus only directly to the computer that corresponds
to that port ID. (PN = port number)
Note: This hotkey functions on the first level of an installation only.
[A] [Enter] Starts Auto Scan. The KVM focus cycles from port to port at the
default 5-second intervals
[A] [n] [Enter] Starts Auto Scan at n-second intervals (n = 1–255 seconds)
[H] Toggles between the default ([Num Lock] [-]) and alternate ([Ctrl]
[F12]) HSM invocation keys.
[T] Toggles between the default ([Scroll Lock] [Scroll Lock]) and
alternate ([Ctrl] [Ctrl]) Port Switching keys.
[F1] Sets the port OS to Windows.
[F2] Sets the port OS to Mac.
[F3] Sets the port OS to Sun.
[F5] Performs a keyboard / mouse reset on the target computer.
[B] Enables/Disables the buzzer.
[R] [Enter] Resets the hotkey settings to their default status. See Factory
Default Hotkeys and Settings, page 79.
[D] Invokes Video DynaSync, ATEN’s exclusive technology that
eliminates boot-up display problems and optimizes resolution
when switching between ports.
[M] Enables/Disables mouse emulation.
[F11] [F] [Enter] Set the selected KVM port to full speed USB
[F11] [L] [Enter] Set the selected KVM port to low speed USB
[F11] [F] [A]
[Enter]
Set the selected KVM station to full speed USB
[F11] [L] [A]
[Enter]
Set the selected KVM station to low speed USB
5. Hotkey Operation
59
[ ← ] Skips to the previous computer on the list, in skip mode.
[ → ] Skips to the next computer on the list, in skip mode.
[ ↑ ] Skips to the next accessible port. If the next accessible port has
cascaded a switch, then it skips to the first accessible port of that
switch, in skip mode.
[ ↓ ] Skips to the previous accessible port. If the previous accessible
port has cascaded a switch, then it skips to the last accessible port
of that switch, in skip mode.
[ESC] or
[Spacebar]
Exits hotkey setting mode.
Key Function
CS1768 / CS1788 User Manual
60
This Page Intentionally Left Blank
61
Chapter 6
Keyboard Emulation
Mac Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Mac keyboard. The emulation mappings are listed in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Mac Keyboard
[Shift] Shift
[Ctrl] Ctrl
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Alt] Alt
[Print Screen] F13
[Scroll Lock] F14
=
[Enter] Return
[Backspace] Delete
[Insert] Help
[Ctrl] F15
CS1768 / CS1788 User Manual
62
Sun Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Sun keyboard when the Control key [Ctrl] is used in conjunction with other
keys. The corresponding functions are shown in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Sun Keyboard
[Ctrl] [T] Stop
[Ctrl] [F2] Again
[Ctrl] [F3] Props
[Ctrl] [F4] Undo
[Ctrl] [F5] Front
[Ctrl] [F6] Copy
[Ctrl] [F7] Open
[Ctrl] [F8] Paste
[Ctrl] [F9] Find
[Ctrl] [F10] Cut
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Ctrl] [H] Help
Compose
-
+
63
Chapter 7
The Firmware Management Utility
Introduction
The purpose of the Windows-based Firmware Management Utility is to
provide an automated process for upgrading all CS1768 / CS1788 switches in
an installation. The program comes as part of a Firmware Upgrade Package
that is specific for each device.
As new firmware versions become available, new firmware upgrade packages
are posted on our website. Check the website regularly to find the latest
information and packages.
Downloading the Firmware Upgrade Package
To download the firmware upgrade package:
1. From a computer that is not part of your KVM installation go to our
website and choose the model name that relates to your device. A list of
available firmware upgrade packages appears.
2. Choose the firmware upgrade package that you wish to install (usually the
most recent) and download it to your computer.
CS1768 / CS1788 User Manual
64
Preparation
To prepare for the firmware upgrade, do the following:
1. Use the Firmware Upgrade Cable provided with this unit to connect a COM
port on your computer to the Firmware Upgrade Port of your switch.
2. Shut down all the computers on the KVM installation.
3. From your KVM switch console, login to the OSD as the administrator
(see p. 35) and select the F4 ADM function.
4. Scroll down to FIRMWARE UPGRADE. Press [Enter], then press [Y] to
invoke Firmware Upgrade mode (see p. 43.)
7. The Firmware Management Utility
65
Starting the Upgrade
To upgrade the firmware:
1. Run the downloaded firmware upgrade package file either by double-
clicking the file icon, or by opening a command line and entering the full
path to it.
The Firmware Upgrade Utility welcome screen appears:
Note: The screens shown in this section are for reference only. The
wording and layout of the actual screens put up by the Firmware
Upgrade Utility may vary slightly from these examples.
2. Read and Agree to the License Agreement (enable the I Agree radio button).
3. Click Next to continue. The Firmware Upgrade Utility main screen
appears. The devices capable of being upgraded are listed in the Device
List panel:
CS1768 / CS1788 User Manual
66
4. Click Next to perform the upgrade.
If you enabled Check Firmware Version, the Utility compares the device's
firmware level with that of the upgrade files. If it finds that the device's
version is higher than the upgrade version, it brings up a dialog box
informing you of the situation and gives you the option to continue or
cancel.
If you didn't enable Check Firmware Version, the Utility installs the
upgrade files without checking whether they are a higher level, or not.
As the upgrade proceeds, status messages appear in the Status Messages
panel, and the progress toward completion is shown on the Progress bar.
7. The Firmware Management Utility
67
Upgrade Succeeded
After the upgrade has completed, a screen appears to inform you that the
procedure was successful.
Click Finish to close the Firmware Upgrade Utility.
Upgrade Failed
If the Upgrade Succeeded screen doesn't appear, it means that the upgrade
failed to complete successfully. See the next section, Firmware Upgrade
Recovery, for how to proceed.
CS1768 / CS1788 User Manual
68
Firmware Upgrade Recovery
There are three conditions that call for firmware upgrade recovery:
When a firmware upgrade is manually aborted.
When the mainboard firmware upgrade fails.
When the I/O firmware upgrade fails.
To perform a firmware upgrade recovery, do the following:
1. Power off the switch.
2. Connect the Firmware Upgrade Cable to its Firmware Upgrade Port.
3. Slide the Firmware Upgrade Recovery Switch to the Recover position.
4. Power the switch back on and repeat the upgrade procedure.
5. After the switch has been successfully upgraded, power it off, and slide the
Firmware Upgrade Recovery Switch back to the Normal position.
6. If the switch is one of the cascaded switches, plug it back into the
installation.
7. Power the switch back on.
7. The Firmware Management Utility
69
OSD Configuration Backup/Restore
The Firmware Management Utility lets you backup the current OSD
configuration of the CS1768 / CS1788, and restore it when necessary. Storing
the OSD configuration settings is useful when deploying more than one
installation that uses the same settings.
Backup
Follow these steps to store a backup file to a local computer:
1. Make sure your computer is connected to the CS1768 / CS1788.
See Preparation, page 64, and follow steps 1–3.
2. When you have selected the F4 ADM function, scroll down to OSD
CONFIG BACKUP / RESTORE. Press [Enter], then press [Y] to invoke
OSD Config Backup / Restore mode.
3. Run the Firmware Management Utility. In the dialog box, choose OSD
Configuration Backup/Restore, then click Next.
4. In the window that appears, click Connect Device.
5. In the Password field, key in a password for the file.
Note: Setting a password is optional. If you do not set one, the file can be
restored without specifying a password.
6. Click Backup.
7. When the browser asks what you want to do with the file, select Save to
disk, then save it in a convenient location.
CS1768 / CS1788 User Manual
70
Restore
Follow these steps to restore a backup file from a local computer:
1. Do steps 1 to 3 of the previous section. See Backup, page 69.
2. Click Restore to recover an OSD configuration stored in the local
computer. If you have previously set a password for this feature, enter the
password in the provided field before clicking Restore. A confirmation
window appears; click Yes to proceed.
3. Browse for the OSD configuration file you want to use and click Restore.
Make sure the backup file is in the local computer.
4. A confirmation window appears when the restore process is done and
successful. Click OK to close it.
71
Appendix
Safety Instructions
General
Read all of these instructions. Save them for future reference.
This product is for indoor use only.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V
phase-to-phase voltage.
To prevent damage to your installation it is important that all devices are
properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug. Always follow your local/national
wiring codes.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
CS1768 / CS1788 User Manual
72
If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
Do not connect the RJ-11 connector marked “UPGRADE” to a public
telecommunication network.
Appendix
73
Rack Mounting
Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflow is provided to devices in the rack.
Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer.
Do not step on or stand on any device when servicing other devices in a
rack.
Caution: Slide/rail (LCD KVM) mounted
equipment is not to be used as a shelf or a work
space.
CS1768 / CS1788 User Manual
74
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://support.aten.com
For telephone support, see Telephone Support, page iii:
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration, including operating system, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
1-949-428-1111
Appendix
75
CS1768 / CS1788 Connection Tables
The following tables indicate the relationship between the number of units and
the number of computers that they control:
MVs Computers MVs Computers MVs Computers MVs Computers
1 1 - 8 20 134 - 141 39 267 - 274 58 400 - 407
2 8 -15 21 141 - 148 40 274 - 281 59 407 - 414
3 15 - 22 22 148 - 155 41 281 - 288 60 414 - 421
4 22 - 29 23 155 - 162 42 288 - 295 61 421 - 428
5 29 - 36 24 162 - 169 43 295 - 302 62 428 - 435
6 36 - 43 25 169 - 176 44 302 - 309 63 435 - 442
7 43 - 50 26 176 - 183 45 309 - 316 64 442 - 449
8 50 - 57 27 183 - 190 46 316 - 323 65 449 - 456
9 57 - 64 28 190 - 197 47 323 - 330 66 456 - 463
10 64 - 71 29 197 - 204 48 330 - 337 67 463 - 470
11 71 - 78 30 204 - 211 49 337 - 344 68 470 - 477
12 78 - 85 31 211 - 218 50 344 - 351 69 477 - 484
13 85 - 92 32 218 - 225 51 351 - 358 70 484 - 491
14 92 - 99 33 225 - 232 52 358 - 365 71 491 - 498
15 99 - 106 34 232 - 239 53 365 - 372 72 498 - 505
16 106 - 113 35 239 - 246 54 372 - 379 73 505 - 512
17 113 - 120 36 246 - 253 55 379 - 386
18 120 - 127 37 253 - 260 56 386 - 393
19 127 - 134 38 260 - 267 57 393 - 400
CS1768 / CS1788 User Manual
76
Specifications
Function CS1768 CS1788
Computer
Connections
Direct 8
Max. 512 (via Cascade)
Port Selection OSD, Hotkey, Pushbutton
Connectors Console
Ports
KB
1 x USB Type A Female (Black)
Video
1 x HDB-15 Female (Blue) / 1 x DVI-I Female (white)
Mouse
1 x USB Type A F (Black)
Speakers
2 x Mini Stereo Jack F (Green; 1 x front panel, 1 x rear panel)
Mic.
2 x Mini Stereo Jack F (Pink; 1 x front panel; 1 x rear panel)
KVM
Ports
KB / Mouse
8 x USB Type B Female (White)
Video
8 x DVI-I Female (White)
Speakers
8 x Mini Stereo Jack Female (Green)
Mic.
8 x Mini Stereo Jack Female (Pink)
F/W Upgrade 1 x RJ11 Female (Black)
Power 1 x DC Jack
USB 2.0 Hub 2 x USB Type A Female (White; 1 x front panel, 1 x rear
panel)
Switches Port Selection 8 x Pushbutton
Reset 1 x Semi-recessed Pushbutton
F/W Upgrade 1 x Slide Switch
LEDs USB Link 8 (Green)
on Line / Selected 8 (Orange)
Power 1 (Dark Green)
Emulation Keyboard / Mouse USB
Video Digital DVI Single Link: 1920 x 1200 DVI Dual Link: 2560 x 1600
Analog 2048 x 1536 (VGA); DDC2B
Scan Interval 1–255 Seconds (Default: 5 secs)
Power Consumption CS1768: DC5.2V~5.3V, 4.53 W
CS1788: DC5.2V~5.3V, 8.26W
Environment
Operating Temp. 0–50ºC
Storage Temp -20–60ºC
Humidity 0–80% RH, Non-condensing
Appendix
77
Physical
Properties
Housing Metal
Weight 2.80 kg
Dimensions
(L x W x H)
43.72 x 16.11 x 4.40 cm
Function CS1768 CS1788
CS1768 / CS1788 User Manual
78
Administrator Login Failure
If you are unable to perform an Administrator login (because the username/
password information has become corrupted, or you have forgotten it, for
example), you can clear the login information with the following procedure:
1. Power off the CS1768 / CS1788 and remove its housing.
2. Short the jumper labeled J30.
3. Power on the switch.
4. When the front panel LEDs flash, power off the switch.
5. Remove the jumper cap from J30.
6. Close the housing and start the CS1768 / CS1788 back up.
After you start back up, you can use the default login procedure (see OSD
Login, page 35) to login.
Appendix
79
Factory Default Hotkeys and Settings
Setting Hotkey Default
Port Switching (Default / Alternate) [T] [Scroll Lock] [Scroll Lock]
Invoking HSM [H] [Number Lock] [-]
Auto Scan Interval [A] [Enter] 5 seconds
Mouse Emulation [M] Enabled
Port Switching Keys (On / Off) [X] [Enter] Enabled
Buzzer [B] Enabled
Video DynaSync [D] Enabled
CS1768 / CS1788 User Manual
80
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in materials and
workmanship for a Warranty Period of two [2] years (warranty period may vary in
certain regions/countries) commencing on the date of original purchase. This warranty
period includes the LCD panel of ATEN LCD KVM switches. Select products are
warranted for an additional year (see A+ Warranty for further details). Cables and
accessories are not covered by the Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty Period. If a
product is detective, ATEN will, at its discretion, have the option to (1) repair said
product with new or repaired components, or (2) replace the entire product with an
identical product or with a similar product which fulfills the same function as the
defective product. Replaced products assume the warranty of the original product for
the remaining period or a period of 90 days, whichever is longer. When the products or
components are replaced, the replacing articles shall become customer property and the
replaced articles shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
Index
A
Activate Beeper
40
ADM
39
Auto Scanning
44
Invoking Auto Scan
49
Pausing Auto Scan
49
Scan Duration
37
Stopping
49
B
Beeper
Activate
40
Control
51
Hotkey Control
51
,
52
BRC
43
Broadcast Mode
43
C
Clear the Name List
40
Components
7
Computer Connection Tables
71
D
desktop mounting
12
E
Edit Port Names
40
F
F1: GOTO
36
F2: LIST
36
F3: SET
37
F4: ADM
39
F5: SKP
43
F6: BRC
43
F7: SCAN
44
F8: LOUT
45
Firmware upgrade
OSD setting
41
port
60
recovery
64
G
GOTO
36
H
Hot Plugging
29
Console Ports
29
KVM ports
29
Hotkey
Beeper Control
51
,
52
Command Mode
38
OSD
37
Selecting the Active Port
48
Hotkey Mode
exiting
48
invoking
47
Hotkey Port Control
47
I
Installation
single stage 17
two stage
20
three stage 22
multi-display 24
Invoking Hotkey Mode
47
K
Keyboard Emulation
Mac
57
Sun
58
L
LIST
36
Logout
45
Logout Timeout
40
LOUT
45
CS1768 / CS1788 User Manual
M
mounting
desktop
12
rack
12
O
Online
Registration
iii
OSD
Backup / Restore 63
Functions
35
Hotkey
33
,
37
Logout
45
Main Screen
33
,
34
Main Screen Headings
34
Navigation
35
Overview
33
Password
33
P
Password
33
Pause
44
Port ID
Display Duration
37
Display Mode
37
Display Position
37
Numbering
30
Port Names
40
Port Selection
30
Manual
30
ports
quick view
41
set operating system
41
Powering Off and Restarting
31
Q
quick view ports
41
R
Rack Mounting
Safety information
69
rack mounting
12
front
13
rear
15
Requirements
Operating Systems
6
OS Support
6
Restore Default Values
40
RoHS
ii
S
Safety Instructions
General
67
Rack Mounting
69
SCAN
44
Scan Duration
37
SCAN/SKIP MODE
38
Screen Blanker
38
Selecting the Active Port
48
SET
37
Accessible Ports
39
Logout Timeout
40
Quick View Ports
41
SJ/T 11364-2006
ii
Skip Mode
43
,
50
Specifications
72
stacking
12
T
Technical Support
70
Telephone support
iii
Timeout
40
Two Stage Installation
20
U
User Notice
iii