Table of Contents
- Compliance Statements
- About this Manual
- Package Contents
- User Information
- Contents
- Chapter 1 Introduction
- Chapter 2 Hardware Setup
- Chapter 3 Basic Operation
- Chapter 4 OSD Operation
- Chapter 5 Hotkey Operation
- Chapter 6 Keyboard Emulation
- Chapter 7 RS-232 Operation
- Chapter 8 The Firmware Management Utility
- Appendix
ATEN CS19216 User Manual
Displayed below is the user manual for CS19216 by ATEN which is a product in the KVM Switches category. This manual has pages.
Related Manuals
CS19208 / CS19216
8/16-Port USB 3.0 4K
DisplayPort KVM Switch
User Manual
CS19208 / CS19216 User Manual
ii
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
KCC Statement
CS19208 / CS19216 User Manual
iii
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
HDMI Trademark Statement
The terms HDMI, HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc.
RoHS
This product is RoHS compliant.
CS19208 / CS19216 User Manual
iv
About this Manual
This User Manual is provided to help you get the most from your CS19208 /
CS19216 system. It covers all aspects of installation, configuration and
operation. An overview of the information found in the manual is provided
below.
Chapter 1, Introduction, introduces you to the CS19208 / CS19216
system. Its purpose, features and benefits are presented, and its front and back
panel components are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary steps for a basic single stage hookup, three-stage cascade, and multi-
display installation are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the CS19208 / CS19216.
Chapter 4, OSD Operation, provides a complete description of the
CS19208 / CS19216's OSD (On Screen Display), and how to work with it.
Chapter 5, Hotkey Operation, details all of the concepts and procedures
involved in the Hotkey operation of your CS19208 / CS19216 installation.
Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac
and PC to Sun keyboard emulation mappings.
Chapter 7, RS-232 Operation, provides details on the functions and RS-
232 commands that you can use to control the CS19208 / CS19216 using a
serial controller.
Chapter 8, The Firmware Management Utility, explains how to use this
utility to upgrade the CS19208 / CS19216's firmware with the latest available
versions and perform an OSD configuration backup/restore.
An
Appendix, provides specifications and other technical information
regarding the CS19208 / CS19216.
CS19208 / CS19216 User Manual
v
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
>Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
>
Run means to
open the Start menu, and then select Run.
Indicates critical information.
CS19208 / CS19216 User Manual
vi
Package Contents
1 CS19208 / CS19216 8/16-Port USB 3.0 4K DisplayPort KVM Switch
with Rack Mounting Kit
2 DisplayPort 1.4 cables
2 USB 3.0 cables
2 audio cables
1 firmware upgrade cable
1 foot pad set (4 pcs)
1 power adapter
1 user instructions*
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
Note: Features may have been added to the CS19208 / CS19216 since this
manual was published. Please visit our website to download the most
up-to-date version.
CS19208 / CS19216 User Manual
vii
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
International http://www.aten.com
North America http://www.aten-usa.com
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
CS19208 / CS19216 User Manual
viii
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
CS19208 / CS19216 User Manual
ix
Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front View CS19208 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front View CS19216 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Rear View CS19208 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear View CS19216 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. Hardware Setup
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Rack Mounting – Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Rack Mounting – Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Single Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Single Stage Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Two Stage Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Two Stage Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Multi-display Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cable Connections for Multi-display Installation . . . . . . . . . . . . . . . . . 22
Multi-display Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Grouping Ports into “Vertical” Channels . . . . . . . . . . . . . . . . . . . . . . . 24
Channels Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CS19208 / CS19216 User Manual
x
3. Basic Operation
Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Manual Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. OSD Operation
OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
OSD Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
OSD Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
F1: Go To . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
F2: List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
F3: Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
F4: Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
F5: SKP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
F8: Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5. Hotkey Operation
Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Hotkey Setting Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Invoking HSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Select the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Invoking Auto Scan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
HSM Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
OSD Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Port OS Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Restore Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Video DynaSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
EDID Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Mouse Emulation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Switching Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
CS19208 / CS19216 User Manual
xi
HSM Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6. Keyboard Emulation
Mac Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
7. RS-232 Operation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Hardware Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
RS-232 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Console Login - HyperTerminal . . . . . . . . . . . . . . . . . . . . . . . . . . 63
RS-232 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Open / Close RS-232 Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Set Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Switch Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Hotkey Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
USB Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Restore Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
KVM Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
EDID Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Broadcast Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
8. The Firmware Management Utility
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . .79
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
OSD Configuration Backup/Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
CS19208 / CS19216 User Manual
xii
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
CS19208 / CS19216 Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . 93
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Factory Default Hotkeys and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
1
Chapter 1
Introduction
Overview
The ATEN CS19208/CS19216 8/16-Port USB 3.0 4K DisplayPort KVM
Switch can effectively access and control up to 8/16 DisplayPort computers
from a single USB keyboard, USB mouse, and monitor console. With its dual
interface console, users can choose between DisplayPort/HDMI video output
supporting high video quality up to 4K DCI (4096 x 2160 @ 60Hz), presenting
crystal-clear visuals.
To meet the needs of easy expansion and flexibility, the CS19208/CS19216
can be cascaded to two levels to control up to 128/256 computers from a single
console. Furthermore, the CS19208/CS19216 supports multi-display function
by stacking up to eight CS19208/CS19216 units to compare and analyze
information on 8 monitors at most, which substantially streamlines the working
environment.
With two patented ATEN technology – Video DynaSync™ and EDID
Expert™, the CS19208/CS19216 can optimize display resolution, accelerate
switching between ports and power up smoothly while eliminating boot-up
display problems.
Besides, the CS19208/CS19216 comes with a built-in USB 3.1 Gen 1 hub
delivering data transfer rates up to 5 Gbps, allowing users to speed up
operations and share USB peripherals instantly. For user-friendly port
selection methods, the CS19208/C19216 offers pushbuttons, hotkeys, RS-232
commands, and OSD with newly-designed UI, bringing effortless and intuitive
operations.
To eliminate security concern, a two-level password authorization is available
to enhance security protection for accessing and controlling computers.
Consolidating these advantageous functionalities, the CS19208/CS19216 is
ideal for server room/computer room management applied in industries with
requirements for high-quality images and multitasking, such as Enterprise,
Government, Production, Telecom, Finance, Medical Healthcare, Industrial
Automation, etc.
Note:
The CS19208 / CS19216 offers two types of installation – 1) standalone/
cascade; and 2) multi-display – that require different cabling setups.
Therefore, the functions of both types are not available in one installation.
CS19208 / CS19216 User Manual
2
For PC compatible computers. Mac and Sun computers must use the USB
cable connections (see Cables, page 5).
Features
One USB console controls up to eight (CS19208) or sixteen (CS19216)
DisplayPort interface computers and two additional USB 3.0 peripheral
devices
Cascadable to two levels – controls up to 128/256 computers (CS19208/
CS19216)
1
Multi-Display feature – stack up to eight CS19208/CS19216 units and
display video from up to 8 monitors (dual display / triple display / quad
display / multi-display)
Video DynaSync™ – an exclusive ATEN technology that eliminates boot-
up display problems and optimizes the resolution when switching among
different sources
EDID Expert™ – selects optimum EDID mode for smooth power-up and
highest quality display
Supports a DisplayPort or HDMI video output – allows you to choose an
appropriate video output and deploy console with flexibility
Superior video quality – up to 4K DCI (4096 x 2160 @ 60Hz)
Built-in 2-port USB 3.1 Gen 1 hub with SuperSpeed 5 Gbps data transfer
rates
Audio enabled – full bass response provides a rich experience for 2.1
channel stereo sound
Supports HD audio
2
Computer selection via pushbuttons, hotkeys, OSD, and RS-232
commands
Independent switching of KVM and USB peripheral focus
3
Two-level (administrator/user) password authorization for enhanced
security protection
Broadcast mode – operations can be simultaneously performed on all
selected computers, such as software installation and upgrading, system-
wide shutdown, etc.
1. Introduction
3
Auto Scan Mode for monitoring all computers
Console mouse port emulation/bypass feature supports most mouse
drivers and multifunction mice
Multilingual keyboard mapping – supports English (US), English (UK),
German (GER.), German (SWISS), French, Hungarian, Italian, Japanese,
Korean, Russian, Spanish, Swedish, Traditional Chinese, and Simplified
Chinese
Mac/Sun keyboard support and emulation
4
Supports hot-plugging
DisplayPort 1.2 compliant; HDCP 2.2 compliant
Multiplatform support – Windows, Linux, Mac, and Sun
Firmware upgradable
Supports multimedia, wireless keyboards and mouse
Note: 1. Cascading between CS19208 and CS19216 is available.
2. HD audio through HDMI and DisplayPort channel cannot be
switched independently.
3. Independent switching is only supported under mouse emulation
mode.
4. PC keyboard combinations emulate Mac/Sun keyboards; Mac/Sun
keyboards work only with their own computers.
CS19208 / CS19216 User Manual
4
Requirements
Console
An HDMI compatible monitor capable of the highest possible resolution
that you will be using on any computer in the installation
A DisplayPort compatible monitor capable of the highest possible
resolution that you will be using on any computer in the installation
Note: For multi-display installations, multiple monitors are required. See
Multi-display Installation, page 22, for details.
A USB mouse
A USB keyboard
Speakers (optional)
Computers
The following equipment must be available on each computer:
A DisplayPort card or DisplayPort port
Note:
The quality of the display is affected by the quality of the DisplayPort
display card. For best results, we recommend you purchase a high
quality product.
For multi-display installations, the computers require multiple
DisplayPort cards. See Multi-display Installation Diagram, page 23,
for details.
A Type-A USB port
Audio ports (optional)
1. Introduction
5
Cables
Only custom USB DisplayPort KVM cable sets, which are specifically
designed to work with this switch, may be used to link to the computers.
Two cable sets are provided with this package.
Note: The quality of the display is affected by the quality and length of the
cables. If you need additional cable sets, please contact your dealer
to purchase the appropriate ones for your switch.
For multi-display installations, standard USB Type-A to USB Type-B
cables and standard DisplayPort cables are also required.
Note: The CS19208 / CS19216 supports speaker ports only. Do not
connect the microphone connector from the KVM cable sets.
Operating Systems
Note:
Supports Linux Kernel 2.6 and higher.
The CS19208 / CS19216 has a built-in USB3.1 hub, and does not support
PCs or operating systems that do not support USB3.1.
OS Version
Windows Windows Server 2008, 2012, 2016, 2019 / Windows 7
SP1 / Windows 8 / Windows 8.1 / Windows 10
Linux CentOS 7 and higher
OpenSUSE Leap 15.1
Snapshot8
10.26 and higher
Ubuntu 16.0.4 and higher
NeoKylin v7.0
SUN Sun Soloaris 11.3 and higher
Mac 10.6 and higher
CS19208 / CS19216 User Manual
6
Components
Front View CS19208
Front View CS19216
2 6 81 4
&
3 5 7
2 6 81 4
&
3 5 7
1. Introduction
7
No. Component Description
1 port selection
pushbuttons
For manual port selection (see Port Selection, page 26, also):
Press a port selection pushbutton for less than two seconds
to bring the KVM, USB hub, and audio focus to the computer
attached to its corresponding port.
Press a pushbutton for longer than two seconds to bring the
KVM and audio focus* to the computer attached to its corre-
sponding port.
Press pushbuttons 1 and 2 simultaneously for 2 seconds to
perform a keyboard and mouse reset start. See Keyboard /
Mouse Reset, page 52, for details.
Press pushbuttons 7 and 8 simultaneously for 2 seconds to
start Auto Scan Mode*. See Auto Scan Mode, page 50, also
Note: Enable mouse emulation for independent switching (see
page 41).
2 port LEDs The Port LEDs are built into the Port Selection Switches. The
left ones are the KVM Port LEDs; the right ones are the USB
LEDs:
KVM
Lights DIM ORANGE to indicate that the computer attached
to the corresponding port is up and running (On Line).
Flashes to indicate that Firmware Upgrade mode is in effect.
Changes to BRIGHT ORANGE to indicate that the computer
attached to its corresponding port is the one that has the
KVM focus (Selected).
Flashes to indicate that the computer attached to its corre-
sponding port is being accessed under Auto Scan mode.
USB
Lights GREEN to indicate that the computer attached to its
corresponding port is the one that has access to the USB
peripherals.
3 firmware
upgrade
recovery
switch
During normal operation and while performing a firmware
upgrade, this switch should be in the NORMAL position. If a
firmware upgrade operation does not complete successfully,
this switch is used to perform a firmware upgrade recovery.
See Firmware Upgrade Recovery, page 85, for details.
4 audio jack The cables from your main speakers plug in here.
Note: The speakers plugged in here have priority over those in
the rear panel.
5 firmware
upgrade port
The firmware upgrade cable that transfers the firmware
upgrade data from the administrator's computer to the
CS19208 / CS19216 plugs into this RJ-11 connector.
CS19208 / CS19216 User Manual
8
6 USB 3.1 Gen
1 peripheral
hub section
USB 3.1 peripherals (printers, scanners, etc.) can plug into this
port (this may require an extra power adapter).
Note: The USB 3.1 hub cannot be accessed through the
switch by computers on the second level of a cascaded
installation.
7 reset button Pressing this switch performs a system reset. When the
system is reset, the switch beeps, and the port LEDs flash in
succession until the reset is complete. After the reset is
complete you can login again.
Note: This switch is recessed and must be pushed with a
small object, such as the end of a paper clip or a ballpoint pen.
8 power LED Lights to indicate that the switch is powered up and ready to
operate.
No. Component Description
1. Introduction
9
Rear View CS19208
Rear View CS19216
No. Component Description
1 grounding terminal The grounding wire used to ground the switch attaches
here.
2 power jack The power adapter cable plugs in here.
3 audio jack The cables from your main speakers plug in here.
Note: The speakers plugged into the front panel have
priority over those plugged here.
4 console port section The cables from your console DisplayPort monitor,
HDMI monitor, USB keyboard, USB mouse, and
speakers plug in here. Each connector is marked with
an appropriate icon to indicate itself.
5 KVM port sections The cables that link the switch to your computers plug
in here. Each KVM port section is comprised of a
speaker jack, a USB type B socket, and DisplayPort
connector.
2
13
4 5
4 5
2
13
CS19208 / CS19216 User Manual
10
This Page Intentionally Left Blank
11
Chapter 2
Hardware Setup
Overview
For convenience and flexibility that allows mixing multiple platforms, the
CS19208 / CS19216 design utilizes custom USB DisplayPort KVM cables that
serve as intermediaries between the switch and the connected computers (refer
to the installation diagram on page 18).
A separate custom USB DisplayPort KVM cable is required for each computer
connection. The custom KVM cables are listed under Cables, on page 5.
Consult your dealer to find out which custom KVM cables best fit your needs.
Installation Types
The CS19208 / CS19216 offers two types of installation – 1) standalone/
cascade; and 2) multi-display – that require different cabling setups. Therefore,
the functions of both types are not available in one installation. See the
following sections in this chapter for details about the different cabling
requirements.
Before You Begin
1. Important safety information regarding the placement of this
device is provided on page 89. Please review it before
proceeding.
2. To prevent damage to your installation from power surges or
static electricity. It is important that all connected devices are
properly grounded.
3. Make sure that power to all devices that you will be installing
has been turned off. You must unplug the power cords of any
computers that have the Keyboard Power On function.
CS19208 / CS19216 User Manual
12
Stacking and Rack Mounting
The CS19208 / CS19216 can be stacked on the desktop or rack mounted at the
front or rear of the rack. The following sections take you through the
procedures for each method.
Note:
Allow at least 5.1 cm on each side for adequate ventilation and
12.7 cm at the rear for power cord and cable clearance.
The standard rack mounting kit does not include screws or cage nuts. If
you need additional screws or cage nuts, contact your rack dealer.
Stacking
The CS19208 / CS19216 can be placed on any level surface that can safely
support its weight and the weight of the attached cables. Make sure that the
surface is clean and free of any materials that can block the exhaust vents or
otherwise interfere with normal operation of the switch.
To place the CS19208 / CS19216, or to stack units if you are cascading them,
remove the backing material from the bottom of the rubber feet that came with
this package, and stick them onto the bottom panel at the corners, as shown in
the diagram, below:
2. Hardware Setup
13
Rack Mounting – Front
1. Remove the screws, one each from the left and right sides near the front of
the unit.
2. Use the M3 x 6 Phillips hex head screws supplied with the rack mounting kit
to screw the rack mounting brackets into the sides near the front of the unit.
3
CS19208 / CS19216 User Manual
14
3. Place the KVM switch in the rack. Position it so that the holes in the
mounting brackets line up with the holes in the rack. Secure the mounting
brackets to the front of the rack.
2. Hardware Setup
15
Rack Mounting – Rear
1. Remove the screws, one each from the left and right sides of the switch
near the rear of the unit.
2. Use the M3 x 6 Phillips hex head screws supplied with the rack mounting kit
to screw the rack mounting brackets into the sides near the rear of the unit.
3
CS19208 / CS19216 User Manual
16
3. Place the KVM switch in the rack. Position it so that the holes in the
mounting brackets line up with the holes in the rack. Secure the mounting
brackets to the rear of the rack.
2. Hardware Setup
17
Single Stage Installation
To set up your single stage CS19208 / CS19216 installation, refer to the
installation diagram on page 18 (the numbers in the diagrams correspond to the
steps, below), and do the following:
1. Ground the CS19208 / CS19216 by connecting one end of a grounding
wire to the Grounding Terminal and the other end to a suitable grounded
object.
Note: Do not omit this step. Proper grounding helps to prevent damage to
the unit from power surges or static electricity.
2. Plug your USB keyboard and USB mouse into the USB console ports from
the Console Ports Section located on the unit’s rear panel.
3. Plug your DisplayPort and/or HDMI monitor(s) into the DisplayPort and/
or HDMI console port(s) from the Console Ports Section located on the
unit’s rear panel and power on the monitor(s).
Note: The CS19208 / CS19216 displays the same source content on both
the DisplayPort and HDMI monitors when DisplayPort and HDMI
console ports are plugged in simultaneously.
4. Plug your speakers into the Audio Jacks located on the unit’s front and rear
panel. The speakers plugged into the front panel have priority over those
plugged into the rear panel.
5. Use the provided cable sets (DisplayPort cable, USB 3.0 cable, and audio
cable) with this package. Plug the DisplayPort connector into any
available DisplayPort port in the KVM Ports Section of the switch (CPU
1, CPU 2, etc.), and then plug the USB 3.0 cable and audio cable into their
corresponding ports.
Note:
Verify that all the connectors are in the same KVM Ports Section (all
in CPU 1, all in CPU 2.).
The CS19208 / CS19216 only supports speaker ports. Do not connect a
KVM cable's microphone connector to the speaker ports.
CS19208 / CS19216 User Manual
18
6. At the other end of the cables from step 5, plug the DisplayPort cable,
USB 3.0 cable, and audio cables into their respective ports on the
computer. Repeat steps 5, and 6 for other PC systems you are installing.
7. (Optional) Plug your USB peripherals into the USB Type-A ports in the
USB 3.1 Gen1 Peripheral Hub Section located on the unit’s front panel.
8. Plug the power adapter that came with your switch into an AC power
source, then plug power adapter cable into the switch’s Power Jack. Now
the CS19208 / CS19216 is turned on.
9. Power on the computers.
Note: Make sure the computers and devices that the CS19208 / CS19216
connects to are also properly grounded.
Single Stage Installation Diagram
3
74
4
CS19216 (Front)
CS19216 (Rear)
8
1
2
5
HDMI and/or DisplayPort
6
DisplayPort Cable
2. Hardware Setup
19
Two Stage Cascade
To control even more computers, additional CS19208 / CS19216 units can be
cascaded from the KVM ports of the First Stage unit. The cascaded CS19208 /
CS19216s that connect back to the First Stage unit are considered Second Stage
units. As many as 128 (CS19208) or 256 (CS19216) computers can be
controlled in a complete two stage installation. A table showing the relation
between the number of computers and the number of units needed to control
them is provided on page 93.
To set up a two stage installation, refer to the Two Stage Installation diagram
on the next page as you do the following:
1. Make sure that power to all the devices you will be connecting up,
including all preexisting devices on the installation, have been turned off.
2. Use the provided cable sets (DisplayPort cable, USB 3.0 cable, and audio
cable) with this package to connect any available KVM Port on the First
Stage unit to the Console ports of the Second Stage unit.
Note: Plug the USB Type-A connector into the lower USB (keyboard) port
in the Console section (they are both marked with a similar icon to
remind you of the correct USB port).
3. Using another provided cable sets (DisplayPort cable, USB 3.0 cable, and
audio cable) with this package, plug the DisplayPort connector into any
available DisplayPort port in the KVM Ports Section of the second stage
switch, then plug the accompanying USB Type-B, and audio cable into
their corresponding USB, and audio jack.
Note:
Verify that all the connectors are in the same KVM Ports Section (all in
CPU 1, all in CPU 2, etc.), and that each socket is marked with an
appropriate icon to indicate itself.
The CS19208 / CS19216 only supports speaker ports. Do not connect a
KVM cable's microphone connector to the speaker ports.
4. At the other end of the cables from step 3, plug the DisplayPort cable,
USB 3.0 cable, and audio cables into their respective ports on the
computer.
5. Repeat steps 3 and 4 for any other PC systems you are installing.
CS19208 / CS19216 User Manual
20
6. For each Second Stage unit, plug the power adapter cable into its Power
Jack, then plug the power adapter into an AC source.
7. Plug the First Stage unit's power adapter cable into its Power Jack, then
plug the power adapter into an AC source.
8. Power on the computers.
Note:
The Power On sequence requires that all Second Stage units be
powered on first. After they are all on, the First Stage units must be
powered on next. Only after all the switches have been powered on in
this sequence, can the computers be powered on.
The USB 3.1 hub cannot be accessed through the switch by computers
on the second level of a cascaded installation.
Make sure the computers and devices that the CS19208 / CS19216
connects to are also properly grounded.
2. Hardware Setup
21
Two Stage Installation Diagram
US B DisplayPort
KVM Cable Set
CS19208 / CS19216 User Manual
22
Multi-display Installation
The CS19208 / CS19216’s multi-display feature allows you to stack two, three,
four, or up to 8 units in a dual/triple/quad-display/multi-display installation to
control up to seven (CS19208) or fifteen (CS19216) computers at once. This
installation requires slightly different cabling than the standard cascade and
offers an extra level of switching flexibility for multiple-monitor installations
where each computer is fitted with multiple video cards.
Note: In a Multi-display installation, the CS19208 can only be connected to
CS19208 units, and the CS19216 can only be connected to CS19216
units.
Cable Connections for Multi-display Installation
To set up your multi-display installation, refer to the installation diagram on the
next page (the numbers in the diagrams correspond to the steps, below), and do
the following:
1. Use a standard USB Type-A-to-USB Type-B cable to connect the Port 8
USB Type-B port on the first stage unit to the USB Type-A port in the
Console section of the second switch.
Note:
Port 8 is reserved to connect the units in a multi-display installation, so
up to seven (CS19208) or fifteen (CS19216) computers can be
attached, using KVM ports 1–7 (CS19208) or ports 1–7/9–16
(CS19216).
Plug the USB Type-A connector into the lower USB (keybaord) Port in
the Console Port Section (both USB Ports are marked with a similar
icon to remind you of the correct USB port).
2. Use DisplayPort cables to connect the DisplayPort KVM port on the
second CS19208 / CS19216 unit to the second video-in port on the
computers.
Note: Only DisplayPort video cables are necessary – the other ports in the
KVM section are not required in this installation.
3. Connect a display to the console section of the second switch.
4. Repeat steps 1–3 for any additional units, up to a total of 8 switches.
2. Hardware Setup
23
5. Connect the cables for the first switch. See Single Stage Installation,
page 17 for full details. All video, audio and peripheral devices must be
connected to the first switch.
6. Power up the CS19208 / CS19216 units, starting with the first switch, and
then power on the computers.
Note: Make sure the computers and devices that the CS19208 / CS19216
connects to are also properly grounded.
Multi-display Installation Diagram
5
Computers with
2/3/4 video inputs
First Switch
5
DisplayPort cables
5
1
USB Type B to
Type A cable
Second Switch
3
Third / Fourth
Stage Units
4
2
CS19208 / CS19216 User Manual
24
Grouping Ports into “Vertical” Channels
Once the cables have been connected and multi-display mode has been selected
in the OSD, the CS19208 / CS19216 auto-detects the channels and displaying
modes.Users can then assign them a channel number as the port name (the
channels are represented by the vertical columns in the diagram below). So, all
the Port 1s become Channel 1, all the Port 2s become Channel 2, ... , and all the
Port 7s become Channel 7. The ports will all be switched at the same time,
channel by channel.
Depending on the number of stages in your stack, a CS19208 / CS19216
installation offers dual display (two stages), triple display (three stages), quad
display (four stages) or multi-display (up to 8 stages) scenarios. For reference
purposes, the example shows a four-stage installation with quad display
functionality.
Note: Only one DisplayPort video signal can be displayed at a time,
depending on the configuration of the CS19208 / CS19216 unit on the
first switch.
Channels Diagram
Ch1
Ch7 Ch6
First
Switch
Second
Switch
Third
Switch
Fourth
Switch
25
Chapter 3
Basic Operation
Hot Plugging
The CS19208 / CS19216 supports hot plugging – components can be removed
and added back into the installation by unplugging their cables from the ports
without the need to shut the unit down. In order for hot plugging to work
properly, the procedures described below must be followed:
Hot Plugging KVM Ports
In order for the OSD menus to correspond to KVM port changes, you must
manually reconfigure the OSD to reflect the new port information. See the F3
SET (page 36) and F4 ADM (page 38), functions for details.
Note: If the computer's operating system does not support hot plugging, this
function may not work properly.
Hot Plugging Console Ports
The keyboard, monitor, and mouse can all be hot plugged. When hot plugging
the mouse:
You may unplug and replug the mouse (to reset the mouse, for example),
as long as you use the same mouse.
If you plug in a different mouse, all the computers on the installation must
be shut down for 10 seconds, then restarted following the power up
sequence described under Steps 6, 7, and 8 under Two Stage Cascade,
page 19
Note: If, after hot plugging there is no response to keyboard and/or mouse
input, perform a Keyboard and Mouse Reset by simultaneously
pressing the 1 and 2 (CS19208 / CS19216) front panel pushbuttons.
CS19208 / CS19216 User Manual
26
Port Selection
The CS19208 / CS19216 provides four port selection methods to access the
computers on the installation: Manual, an OSD (on-screen display) menu
system, Hotkeys, and RS-232 commands.
For OSD (on-screen display), see Chapter 4 OSD Operation, page 29 for
more information.
For Hotkeys operation, see Chapter 5 Hotkey Operation, page 47 for more
information.
For RS-23 commands, see Chapter 7 RS-232 Operation, page 61 for more
information.
Manual Port Switching
Use the front panel pushbutton switches to manually switch to a port.
Port ID Numbering
Each port on a CS19208 / CS19216 installation is assigned a unique Port ID.
You can directly access any computer on any level of the installation by
specifying the Port ID that the computer is connected to – either with the OSD
(see OSD Operation, page 29), or with the Hotkey port selection method (see
Hotkey Operation, page 47).
A computer attached to a primary unit has a two digit Port ID (from 01–08
for the CS19208, or 01–16 for the CS19216) that corresponds to the KVM
port number that it is connected to.
A computer attached to a secondary unit has a four digit Port ID.
The first two digits represent the KVM port number on the primary unit
and the second two digits represent the KVM port number on the
secondary unit that the computer is connected to. For example, a Port ID
of 02–08 would refer to a computer that is connected to KVM port 8 of a
secondary unit that links back to KVM port 2 of the primary unit.
3. Basic Operation
27
Powering Off and Restarting
If it becomes necessary to power off a CS19208 / CS19216, do the following
before restarting it:
1. Unplug the CS19208 / CS19216 from its power source.
2. Shut down all the computers that are attached to it.
Note: Unplug the power cords of any computers that have the Keyboard
Power On function. Otherwise, the CS19208 / CS19216 will still
receive power from the computers.
3. Wait 10 seconds, then plug the CS19208 / CS19216 back in.
4. Power on the computers.
Note: If there are stations cascaded down from the primary CS19208 /
CS19216, all the cascaded stations and the computers attached to
them must be shut down as well.
CS19208 / CS19216 User Manual
28
This Page Intentionally Left Blank
29
Chapter 4
OSD Operation
OSD Overview
The on-screen display (OSD) is a mouse and keyboard enabled, menu driven
method to handle computer control and switching operations. All procedures
start from the OSD main screen.
Manufacturing Number
The “MFG Number” (Manufacturing Number) is an internal serial number
used by ATEN’s factory and technical support staff to identify products. This
number does not affect products’ warranty. If your product requires after-sales
services, you may provide the MFG Number to ATEN’s sales or technical
support staff to identify the product and model number.
OSD Login
The OSD incorporates a two level (administrator / user) password system.
Before the OSD main screen displays, a login screen appears requiring a
password. If this is the first time that the OSD is used, or if the password
function has not been set, simply use default username and password:
administrator / password to login. After you have logged in for the first time,
you will be asked to change the password for security purpose, please follow
the on-screen instructions to setup your new password. The OSD main screen
displays in administrator mode. In this mode, you have administrator
privileges, with full access to all functions, and can set up operations (including
password authorization) as you like.
CS19208 / CS19216 User Manual
30
OSD Hotkey
You can display the OSD on the console monitor while also viewing the
display of any port on the CS19208 / CS19216 by pressing the [Scroll Lock]
key twice.
Note: You can optionally change the OSD hotkey to the Ctrl key, in which
case you would press [Ctrl] twice (see OSD HOTKEY, page 36). With
this method, you must press the same [Ctrl] key.
OSD Main Screen
When you invoke the OSD, a screen similar to the one below appears:
Note:
4. OSD Operation
31
The diagram depicts the administrator's main screen. The user main screen
does not show the F4 and F6 functions, since these are reserved for the
administrator and can't be accessed by users.
The OSD always starts in list view, with the highlight bar at the same
position it was in the last time it was closed.
Only the ports that have been set accessible by the administrator for the
current logged in user are visible (see SET ACCESSIBLE PORTS,
page 39).
Enable Mouse Emulation to operate the OSD using mouse. When the
Mouse Emulation is disabled, you can only operate the OSD using
keyboard.
a) To enable the Mouse Emulation via OSD, see Mouse Emulation,
page 41.
b) To enable the Mouse Emulation via hotkeys, see Mouse Emulation
Control, page 55.
If the port list is collapsed, click on a switch number, or move the highlight
bar to it then press the Enter key to expand the list. Similarly, to collapse a
switch’s port list, click on the switch number, or move the highlight bar to
it then press the right Enter key to collapse the list.
OSD Main Screen Headings
OSD Navigation
To dismiss the menu, and deactivate OSD, click
at the upper right
corner of the OSD window; or press [Esc].
PN This column lists the port ID numbers for all the KVM ports on the
installation. The simplest method to access a particular computer is
move the highlight bar to it, then press Enter.
QV If a port has selected for quick view scanning (see SET QUICK VIEW
PORTS, page 40), a check mark
(
√
)
displays in this column.
PW The computers that are powered on and are online have a sun symbol
in this column .
NAME If a port has been given a name (see EDIT PORT NAMES, page 40), its
name appears in this column.
CS19208 / CS19216 User Manual
32
To log out, click
at the left of the main screen, or press
[F8].
To move up or down through the list one screen at a time, click the up and
down arrow symbols (
), or use the [Pg Up] and [Pg Dn] keys. If
there are more list entries than what can appear on the main screen, the
screen will scroll.
To activate a port, click it, or move the highlight bar to it then press
[Enter].
After executing any action, you automatically go back to the menu one
level above.
4. OSD Operation
33
OSD Functions
OSD functions are used to configure and control the OSD. For example, you
can rapidly switch to any port, scan selected ports, limit the list you wish to
view, designate a port as a quick view port, create or edit a port name, or make
OSD setting adjustments.
To access an OSD function:
1. Either click on the function key field on the left of the main screen, or
press a function key on the keyboard.
2. In the submenus that appear make your choice either by clicking it, or
moving the highlight bar to it, then pressing [Enter].
3. Press [Esc] to return to the previous menu level.
CS19208 / CS19216 User Manual
34
F1: Go To
Clicking
or pressing [F1] activates the Go To function. Go To
allows you to switch directly to a port by keying in the port's ID. Enable mouse
emulation for independent switching (see page 41), for this function to work.
To use the search method, key in the Port ID; then press [Enter] to switch
KVM, Audio and USB focus; or [Spacebar] to switch KVM and Audio
only.
4. OSD Operation
35
F2: List
Clicking
or pressing [F2] activates the List function. This
function lets you broaden or narrow the scope of which ports the OSD displays
on the main screen. The submenu choices and their meanings are given in the
table below.
Move the highlight bar to the choice you want, then press [Enter]. A check
mark (
√
) appears before the choice to indicate that it is the currently selected
one.
Choice Meaning
ALL Lists all of the ports on the installation that have been set accessible
by the administrator for the current logged in user.
Quick View Lists only the ports that have been selected as quick view ports (see
SET QUICK VIEW PORTS, page 40).
Powered On Lists only the ports that have their attached computers powered on.
Quick View +
Powered On
Lists only the ports that have been selected as quick view ports (see
SET QUICK VIEW PORTS, page 40), and that have their attached
computers powered on.
CS19208 / CS19216 User Manual
36
F3: Set
Clicking
or pressing [F3] activates the Set function. This function
allows the administrator and each user to set up his own working environment.
A separate profile for each is stored by the OSD and is activated according to
the username that was provided during login.
To change a setting:
1. Click it; or move the highlight bar to it, then press [Enter].
2. After you select an item, a submenu with further choices appears. To make
a selection, either click it; or move the highlight bar to it, then press
[Enter]. A check mark (
√
) appears before the selected choice to indicate
which one it is. The settings are explained in the following table:
Setting Function
OSD Hotkey Selects which hotkey activates the OSD function:
[Scroll Lock] [Scroll Lock] or [Ctrl] [Ctrl].
Since the [Ctrl] key combination may conflict with programs running
on the computers, the default is the [Scroll Lock] combination.
Port ID Display
Position
Allows each user to customize the position where the port ID
appears on the screen. The default is the upper left corner, but
users can choose to have it appear anywhere on the screen.
Use the mouse or the arrow keys plus Pg Up, Pg Dn, Home, and
End (on the numeric keypad with Num Lock off). Arrow keys move
the position one space at a time. Pg Up and Pg Dn brings position
to the top or bottom. Home and End brings the position to the
rightmost and leftmost of the screen.To position the port ID display,
then single-click or press [Enter] to lock the position and return to
the Set submenu.
4. OSD Operation
37
Port ID Display
Duration
Determines how long a port ID displays on the monitor after a port
change has taken place. The choices are: 3 Seconds (default) and
Always Off.
Port ID Display
Mode
Selects how the port ID is displayed: the port number plus the port
name (Port Number + Port Name) (default); the port number
alone (Port Number); or the port name alone (Port Name).
Scan Duration Determines how long the focus dwells on each port as it cycles
through the selected ports in Auto Scan mode (see F7 SCAN,
page 44). Key in a value from 1–255 seconds, then press [Enter].
Default is 5 seconds; a setting of 0 disables the SCAN function.
Note: We recommend to set the scan duration to 10 seconds.
Scan-Skip Mode Selects which computers will be accessed under skip mode
(see F5: SKP, page 42), and Auto Scan mode (see F7: SCAN,
page 44. Choices are:
ALL - All the ports which have been set accessible (see SET
ACCESSIBLE PORTS, page 39);
QUICK VIEW - Only those ports which have been set accessible
and have been selected as quick view ports (see SET QUICK
VIEW PORTS, page 40);
POWERED ON - Only those ports which have been set accessible
and are powered on;
QUICK VIEW + POWERED ON - Only those ports which have
been set accessible and have been selected as quick view ports
and are powered on. The default is ALL.
Note: The quick view choices only show up on the administrator's
screen, since only he has Quick View setting rights (see SET
QUICK VIEW PORTS, page 40).
Screen Blanker If there is no input from the console for the amount of time set with
this function, the screen is blanked. Key in a value from 1–30
minutes, then press [Enter]. The default setting of 0 disables this
function. The screen will be blanked in the amount of time set
(count from the moment when OSD is closed)
Hotkey
Command Mode
Enables / disables the hotkey command function in case a conflict
with programs running on the computers occurs.
Hotkey Sets the keyboard shortcut for invoking Hotkey Mode (see Hotkey
Setting Mode, page 48). Choices are: [NUM LOCK] + [-] (minus)
(default), and [CTRL] + [F12].
OSD Language Sets the language used in the OSD. Choices are: English (Default),
German, Japanese, Simplified Chinese, Traditional Chinese,
Spanish, French, and Russian.
CS19208 / CS19216 User Manual
38
F4: Admin
Clicking
or pressing [F4] activates Admin function. F4 is an
administrator only function. It allows the administrator to configure and
control the overall operation of the OSD. To change a setting, click on the
settings item you want to configure, or use the up and down arrow keys to move
the highlight bar to it then press [Enter].
After you select an item, a submenu with further choices appears. Click an
item, or move the highlight bar to it then press [Enter]. A check mark (
√
)
appears before the selected item so that you know which one it is. The settings
are explained in the following table:
4. OSD Operation
39
Setting Function
Set User Login This function is used to set usernames and passwords for the
administrator and users:
1. Usernames and passwords for one administrator and four users
can be set.
2. After you select the administrator field or one of the user fields,
a field that allows you to key in the username and password
appears. Usernames and passwords can be from 1 to 16
characters long and can consist of any combination of letters
and numbers (A–Z, 0–9) and some additional keys (* ( ) + : - , ?
. / space).
3. For each individual, key in the username and password, confirm
the password, choose SAVE, then press [Enter].
4. To modify or delete a previous username and/or password, use
the backspace key to erase individual letters or numbers. Press
[Enter] when done.
Note: Usernames and passwords are not case sensitive.
Usernames are displayed in capital letters in the OSD.
Set Accessible
Ports
This function allows the administrator to define user access to the
computers on the installation on a port-by-port basis.
For each user, select the target port; then press the [Spacebar] to
cycle through the choices: F (full access), V (view only), or blank.
Repeat until all access rights have been set, then press [Enter].
The default is F for all users on all ports.
Note:
A blank setting means that no access rights are granted. The
port will not show up on the user's LIST on the main screen.
The administrator always has full access to all ports.
Set Logout
Timeout
If there is no input from the console for the amount of time set with
this function, the user is automatically logged out. A login is
necessary before the console can be used again.
This enables other users to gain access to the computers when the
original user is no longer accessing them, but has forgotten to log
out. To set the timeout value, key in a number from 1–180 minutes,
then press [Enter]. The default setting of 0 disables this function.
Note: This feature does not function if Set Login Mode is disabled.
See Set Login Mode, page 41.
CS19208 / CS19216 User Manual
40
Edit Port Names To help remember which computer is attached to a particular port,
every port can be given a name. This function allows the
administrator to create, modify, or delete port names.
To edit a port name:
1. Click the port, or use the navigation keys to move the highlight
bar to it.
2. Key in the new port name, or modify/delete the old one. The
maximum number of characters allowed for the port name is 12.
Legal characters include:
All alpha characters: A–Z
All numeric characters: 0–9
* ( ) + : - , ? . /
Case does not matter; the OSD displays the port name in all
capitals no matter how they were keyed in.
3. When you have finished editing, press [Enter] to have the
change take effect. To abort the change, press [Esc].
Restore Default
Values
This function is used to undo all changes and return the setup to
the original factory default settings (See Factory Default Hotkeys
and Settings, page 97) except for the port name list, username and
password information, which are saved.
Clear The Name
List
This function clears the port name list.
Activate Beeper Choices are Y (on), or N (off). When activated, the beeper sounds
whenever a port is changed; when activating the Auto Scan
function (see F7 SCAN, page 44); or an invalid entry is made on an
OSD menu. The default is Y.
Set Quick View
Ports
This function lets the administrator select which ports to include as
quick view ports.
To select/deselect a port as a quick view port, use the navigation
keys to move the highlight bar to it, then press [Spacebar].
When a port has been selected as a quick view port, A check
mark
(
√
)
displays in the QV column of the LIST on the main
screen. When a port is deselected, the check mark
(
√
)
disap-
pears.
If one of the quick view options is chosen for the LIST view (see
F2 LIST, page 35), only a port that has been selected here
will display on the list.
If one of the quick view options is chosen for auto-scanning
(See Scan-Skip Mode, page 37), only a port that has been
selected here will be auto-scanned.
The default has no ports selected for quick view.
4. OSD Operation
41
Set Operating
System
This function allows the administrator to define the operating
system for the computer connected to each KVM port. The default
setting is Win (PC compatible).
To set the port operating system:
1. From the list, select the port for which you wish to set the com-
puter's operating system.
2. Set the operating system by pressing [Spacebar] to cycle
through Win, MAC, SUN, or Other.
3. Press [Esc] to exit. The operating system you selected is
assigned to the KVM port.
Firmware
Upgrade
In order to upgrade the CS19208 / CS19216 firmware (see
page 79), you must first enable Firmware Upgrade mode with this
setting.
When you bring up this menu, the current firmware version levels
are displayed. Select Y to enable Firmware Upgrade mode, or
select [Esc] to leave this menu without enabling it.
Keyboard
Language
Sets the language for the computer keyboard attached to the KVM
port. To select a keyboard language, single-click it, or use the
navigation keys to move the highlight bar to it, then press [Enter].
Choices are: Auto (default), (US) English, (UK) English, German
(Deutch), German (SWISS), French, Hungarian, Italian, Japanese,
Korean, Russian, Spanish, Swedish, Traditional Chinese, and
Simplified Chinese.
Mouse Emulation Enables / disable mouse emulation function.
Note: Supported in the first level of an installation only. Enable
mouse emulation to perform any independent switching of a port
and for Auto Scan Mode or Skip Mode to work.
Activate Multi-
Display
Enables multi-display mode for dual, triple, quad, or multi display
mode in multiple-monitor installations where each computer is
fitted with multiple video cards. See Multi-display Installation,
page 22, for full details.
Note: multi-display mode must be enabled on the OSD before the
cables are connected.
OSD Config Back
/ Restore
Enters OSD Configuration Backup / Restore mode. The Firmware
Management Utility lets you backup the current OSD configuration
of the CS19208 / CS19216, and restore it when necessary. Storing
the OSD configuration settings is useful when deploying more than
one installation that uses the same settings. See OSD
Configuration Backup/Restore, page 86, for full details.
Set Login Mode This function allows the administrator to request users to login or
not. When the login dialog box is disabled, the system disables the
login/logout function. If the system is re-started, the login/logout
function remains disabled.
CS19208 / CS19216 User Manual
42
F5: SKP
Clicking
or pressing [F5] invokes Skip (SKP) mode. This function
enables you to easily skip backward or forward – switching the console focus
from the currently active computer port to the previous or next accessible one.
Enable mouse emulation for Skip mode to work (see page 41).
The selection of computers available for skip mode switching is made with
the Scan–Skip mode setting under the F3: SET function (see page 36).
When you are in skip mode:
press [
←
] to skip to the previous accessible port on the list
press [
→ ]
to skip to the next accessible port on the list
press [
↑
] to skip to the previous accessible port. If the previous accessible
port has cascaded a switch, then it skips to the last accessible port of that
switch
press [
↓
] to skip to the next accessible port. If the next accessible port has
cascaded a switch, then it skips to the first accessible port of that switch
Note: When you skip, you only skip to the previous or next accessible
computer that is in the Scan–Skip mode selection (see page 37).
If a port has been selected for Scan–Skip mode, when the focus switches to
that port, a set of [
↑
], [
↓
], [
←
], [
→ ]
symbol appears before its port
ID displays.
While skip mode is in effect, the console will not function normally. You
must exit skip mode in order to regain control of the console.
To exit skip mode, press [Spacebar] or [Esc].
4. OSD Operation
43
F6: BRC
F6 is an administrator only function. Clicking or pressing [F6],
invokes Broadcast (BRC) mode. When this function is in effect, commands
sent from the console are broadcast to all available computers on the
installation.
This function is particularly useful for operations that need to be performed on
multiple computers, such as performing a system wide shutdown, installing or
upgrading software, etc.
While BRC mode is in effect, a speaker symbol appears before the port ID
display of the port that currently has the console focus. When the port ID
with the speaker symbol displays.
While BRC mode is in effect, the mouse will not function normally. You
must exit BRC mode in order to regain control of the mouse.
To exit BRC mode, invoke the OSD (with the OSD hotkey), then click the
F6 field, or press [F6], to turn BRC mode off.
When BRC mode is in effect, the Scroll Lock LED flashes. It stops
flashing and reverts to normal status when you exit BRC.
CS19208 / CS19216 User Manual
44
F7: SCAN
Clicking
or pressing [F7] invokes Auto Scan mode. This
function allows you to automatically switch among the available computers at
regular intervals so that you can monitor their activity without having to take
the trouble of switching yourself. Enable mouse emulation for Auto Scan to
work (see page 41).
The selection of computers to be included for auto-scanning is made with
the Scan–Skip mode setting under the F3: SET function (see page 37).
The amount of time that each port displays for is set with the Scan
Duration setting under the F3: SET function (see page 37). When you
want to stop at a particular location, press the [Spacebar] to stop scanning.
If the scanning stops on an empty port, or one where the computer is
attached but is powered Off, the monitor screen will be blank, and the
mouse and keyboard will have no effect. After the Scan Duration time is
up, the scan function will move on to the next port.
As each computer is accessed, an S appears in front of the port ID display
to indicate that it is being accessed under Auto Scan mode. When the port
ID with the symbol displays, the background screen is blank.
While Auto Scan mode is in effect, the console will not function normally.
You must exit Auto Scan mode in order to regain control of the console.
While you are in Auto Scan mode, you can pause the scanning in order to
keep the focus on a particular computer either by pressing P, or with a left-
click of the mouse. See Invoking Auto Scan, page 50, for details.
To exit Auto Scan mode, press the [Spacebar] or [Esc].
4. OSD Operation
45
F8: Logout
Clicking , or pressing [F8] logs you out of OSD control of the
computers, and blanks the console screen. This is different from simply
pressing [Esc] when you are at the main screen to deactivate the OSD. With
this function you must log in all over again to regain access to the OSD,
whereas with [Esc], all you have to do to reenter the OSD is tap the OSD
hotkey.
Note: 1. When you reenter the OSD after logging out, the screen stays blank
except for the OSD main screen. You must input your username and
password before you can continue.
2. If you reenter the OSD after logging out, and immediately use [Esc]
to deactivate the OSD without having selected a port from the OSD
menu, a NULL PORT message displays on the screen. The OSD
hotkey will bring up the main OSD screen.
CS19208 / CS19216 User Manual
46
This Page Intentionally Left Blank
47
Chapter 5
Hotkey Operation
Hotkey Port Control
Hotkey port control allows you to provide KVM focus to a particular computer
directly from the keyboard. The CS19208 / CS19216 provides the following
hotkey port control features:
Selecting the Active Port
Auto Scan Mode Switching
Skip Mode Switching
Computer Keyboard / Mouse Reset
Enable / Disable Mouse Emulation
The following settings can also be controlled in Hotkey Setting Mode (HSM):
Setting the Beeper
Setting the HSM Hotkey
Setting the OSD Hotkey
Setting the Port Operating System
Restoring the OSD Default Values
Setting the EDID Mode
Setting the Video DynaSync Mode
Setting the Switch Mode Selection
Note: Enable mouse emulation to perform any independent switching of a port
and for Auto Scan Mode or Skip Mode to work (see page 55).
CS19208 / CS19216 User Manual
48
Hotkey Setting Mode
Hotkey Setting Mode is used to set up your CS19208 / CS19216 switch
configuration. All operations begin with invoking Hotkey Setting Mode
(HSM).
Invoking HSM
To invoke HSM do the following:
1. Press and hold down [Num Lock].
2. Press and release [-].
3. Release [Num Lock].
or
1. Hold down the [Ctrl] key;
2. Press and release the [F12] key;
3. Release the [Ctrl] key:
When HSM is active:
A command line appears on the monitor screen. The command line prompt
is the word HOTKEY: in white text on a blue background, and displays the
subsequent hotkey information that you key in.
Ordinary keyboard and mouse functions are suspended – only hotkey
compliant keystrokes (described in the sections that follow), can be input.
Pressing [Esc] exits HSM.
5. Hotkey Operation
49
Select the Active Port
Each KVM port is assigned a port ID (see Port ID Numbering, page 26). You
can directly access any computer on the installation with a hotkey combination
that specifies the port ID of the KVM port that a computer is connected to. To
access a computer using hotkeys:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Key in the port ID.
The port ID numbers display on the command line as you key them in. If
you make a mistake, use [Backspace] to erase the wrong number.
3. Press [Enter].
After you press [Enter], the KVM focus switches to the designated
computer and you automatically exit HSM.
Note: In HSM, KVM focus will not switch to a port if an invalid switch or
port number is entered. The hotkey command line will continue to
display on the screen until you enter a valid switch and port number
combination, or exit HSM.
Note: The [PN] stands for the computer’s Port ID number (1, 2, 3, or 4). See
Port ID Numbering, page 26 for details. Replace the [PN] with the
appropriate Port ID when entering Hotkey combinations.
Hotkey Action
[PN] [Enter] Brings the KVM, USB hub, and audio focus to the
computer attached to the port corresponding to the
specified Port ID.
[PN] [K] [Enter] Brings only the KVM and audio focus to the computer
attached to the specified port. The USB hub and audio
focus remain where they are.
[PN] [U] [Enter] Brings only the USB hub focus to the computer
attached to the specified port. The KVM and audio
focus remain where they are.
CS19208 / CS19216 User Manual
50
Auto Scan Mode
Auto Scan automatically switches, at regular intervals, among all the KVM
ports that have been set as accessible under Scan–Skip Mode, so that their
activity can be monitored automatically. See Scan–Skip Mode on page 37 for
more information.
Invoking Auto Scan:
To start Auto Scan, key in the following Hotkey combination:
1. Enable mouse emulation (see page 55).
2. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
3. Press [A]. After you press A, then [Enter], you automatically exit HSM,
and enter Auto Scan mode.
While you are in Auto Scan mode, you can pause the scanning in order
to keep the focus on a particular computer either by pressing P or with
a left click of the mouse. During the time that auto-scanning is paused,
the command line displays: AUTO SCAN: PAUSED.
Pausing when you want to keep the focus on a particular computer is
more convenient than exiting Auto Scan mode because when you
resume scanning, you start from where you left off. If, on the other
hand, you exited and restarted, scanning would start over from the very
first computer on the installation.
To resume Auto Scanning, press any key or left-click. Scanning
continues from where it left off.
While Auto Scan mode is in effect, ordinary keyboard and mouse
functions are suspended – only Auto Scan mode compliant keystrokes
and mouse clicks can be input. You must exit Auto Scan mode in order
to regain normal control of the console.
4. To exit Auto Scan mode press [Esc] or [Spacebar]. Auto-scanning stops
when you exit Auto Scan mode.
Note: Enable mouse emulation to perform any independent switching of a
port and for Auto Scan Mode or Skip Mode to work (see page 55)
5. Hotkey Operation
51
Skip Mode
This feature allows you to switch between computers in order to monitor them
manually. You can dwell on a particular port for as long as you like – as
opposed to auto-scanning, which automatically switches after a fixed interval.
To invoke Skip mode, key in the following hotkey combination:
1. Enable mouse emulation (see page 55).
2. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
3. Key in [
↑
], [
↓
], [
←
], or [
→ ].
After you press an arrow key, you automatically exit HSM and enter
Skip mode where you can switch ports as follows:
Once you are in Skip mode, you can keep on skipping by pressing the
arrow keys. You don't have to use the [Num Lock] + [-] combination
again.
While Skip mode is in effect, ordinary keyboard and mouse functions
are suspended – only Skip mode compliant keystrokes can be input.
You must exit Skip mode in order to regain normal control of the
console.
4. To exit Skip mode, press [Esc] or [Spacebar].
Note: Enable mouse emulation to perform any independent switching of a port
and for Auto Scan Mode or Skip Mode to work (see page 55).
←Skips to the previous accessible port. (See Scan/Skip Mode,
page 37, for information regarding accessible ports.)
→Skips to the next accessible port.
↑Skips to the previous accessible port. If the previous accessible
port has cascaded a switch, then it skips to the last accessible
port of that switch.
↓Skips to the next accessible port. If the next accessible port has
cascaded a switch, then it skips to the first accessible port of that
switch.
CS19208 / CS19216 User Manual
52
Keyboard / Mouse Reset
If the keyboard or mouse cease to function on the computer connected to the
currently selected port, you can perform a keyboard / mouse reset on the
computer. This function is essentially the same as unplugging and replugging
the keyboard and mouse on the target computer. To perform a computer
keyboard / mouse reset, key in the following hotkey combination:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [F5].
After you press [F5] you automatically exit HSM and regain keyboard and
mouse control on the computer connected to the KVM port. If you fail to regain
keyboard / mouse control on the computer after pressing [F5], perform a
console keyboard and mouse reset.
Hotkey Beeper Control
The beeper (see Activate Beeper, page 40) can be hotkey toggled on and off.
The default setting is enabled. To toggle the beeper, key in the following
hotkey combination:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [B].
After you press [B], the beeper toggles on or off. The command line displays
BEEPER ON or BEEPER OFF for one second; then the message disappears
and you automatically exit HSM.
HSM Hotkey Control
The HSM Hotkey (see Hotkey, page 37) can be toggled between
[Num Lock] + [-], and [Ctrl] + [F12]. To toggle the HSM Hotkey:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [H].
After you press [H], the command line displays HOTKEY HAS BEEN
CHANGED for one second; then the message disappears and you
automatically exit HSM.
5. Hotkey Operation
53
OSD Hotkey Control
The OSD Hotkey (see OSD Hotkey, page 36) can be toggled between [Scroll
Lock], [Scroll Lock] and [Ctrl], [Ctrl]. To toggle the OSD Hotkey, key in the
following hotkey combination:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [T].
After you press [T], the command line displays HOTKEY HAS BEEN
CHANGED for one second; then the message disappears and you
automatically exit HSM.
Port OS Control
A port’s operating system can be changed to match that of the computer
attached to the port. To change a port’s operating system, key in the following
hotkey combination:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Key in [F1], [F2], or [F3], the Function of [F1], [F2], and [F3] keys is
listed in the following table:
After pressing a function key you automatically exit HSM.
Key Description
F1 Sets the Port OS to Windows
F2 Sets the Port OS to Mac
F3 Sets the Port OS to Sun
CS19208 / CS19216 User Manual
54
Restore Default Values
This administrator-only hotkey restores the CS19208 / CS19216 default
values. see Factory Default Hotkeys and Settings, page 97. To restore the
default values, key in the following hotkey combination:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [R].
3. Press [Enter].
After you press [Enter], the command line displays RESET TO DEFAULT
SETTING for one second; then the message disappears and you
automatically exit HSM.
Video DynaSync
Video DynaSync is ATEN’s exclusive technology that eliminates boot-up
display problems and optimizes resolution when switching between ports. The
default setting is enabled. To invoke Video DynaSync, do the following:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [D].
Note: If the monitor is disconnected and reconnected, the CS19208 /
CS19216 re-executes Video DynaSync.
5. Hotkey Operation
55
EDID Mode
To configure an EDID mode for the CS19208 / CS19216, do the following:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [V].
3. Key in [1], [2], [3], or [4], the Function of [1], [2], [3], and [4] keys is
listed in the following table:
4. Press [Enter]. After pressing [Enter] you automatically exit HSM.
Mouse Emulation Control
The default setting is enabled. To disable, do the following:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [M].
This procedure is a toggle. Repeat to enable.
Note: Enable mouse emulation to perform any independent switching of a port
and for Auto Scan Mode or Skip Mode to work.
Key Description
1 Sets the switch to read
DisplayPort monitor’s EDID
(Default)
2 Sets the switch to read HDMI
monitor’s EDID
3 Sets the switch to ATEN default
EDID mode
4 Sets the switch to remix mode
CS19208 / CS19216 User Manual
56
Switching Mode Selection
This administrator-only hotkey allows you to select an appropriate switching
mode between Normal Switching Mode or Fast Switching Mode.
Note: This hotkey will only be available with CS19208 / CS19216’s firmware
version v1.1.101 or higher.
To change the switching mode, key in the following hotkey combination:
1. Invoke HSM with the [Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [P].
3. Key in [1] or [2], the Function of [1] and [2] keys is listed in the following
table:
4. Press [Enter]. After you press [Enter], the command line displays Normal
Switching Mode or Fast Switching Mode for one second; then the message
disappears and you automatically exit HSM.
Note: The configuration of Fast Switching Mode might not work with some
monitors. If your video output does not display successfully or work
properly, please use the default Normal Switching Mode instead.
Key Description
1 Sets the KVM to Normal
Switching Mode (Default)
2 Sets the KVM to Fast Switching
Mode
5. Hotkey Operation
57
HSM Summary Table
After invoking HSM (see page 48), key in one of the following keys to perform
the corresponding function:
Key Function
[PN] [Enter] Switches KVM, Audio, and USB focus directly to the
computer that corresponds to that port ID. (PN = port
number)
[PN] [K] [Enter] Switches KVM and Audio focus directly to the computer
that corresponds to that port ID. (PN = port number)
[PN] [U] [Enter] Switches USB focus only directly to the computer that
corresponds to that port ID. (PN = port number)
Note: This hotkey functions on the first level of an
installation only.
[A] [Enter] Starts Auto Scan. The KVM focus cycles from port to port
at the default 5-second intervals
[A] [n] [Enter] Starts Auto Scan at n-second intervals (n = 0–255
seconds)
Note: When n=0, the Auto Scan will not be activated.
[H] Toggles between the default ([Num Lock] [-]) and alternate
([Ctrl] [F12]) HSM invocation keys.
[T] Toggles between the default ([Scroll Lock] [Scroll Lock])
and alternate ([Ctrl] [Ctrl]) OSD Hotkey.
[F1] Sets the port OS to Windows.
[F2] Sets the port OS to Mac.
[F3] Sets the port OS to Sun.
[F5] Performs a keyboard / mouse reset on the target
computer.
[B] Enables/Disables the beeper.
[R] [Enter] Resets the hotkey settings to their default status. See
Factory Default Hotkeys and Settings, page 97.
[D] Invokes Video DynaSync, ATEN’s exclusive technology
that eliminates boot-up display problems and optimizes
resolution when switching between ports.
CS19208 / CS19216 User Manual
58
Note: Enable mouse emulation to perform any independent switching of a port
and for Auto Scan Mode or Skip Mode to work (see page 55).
[V] [n] [Enter] Sets EDID Mode.
n = 1, read DisplayPort monitor’s EDID.
n = 2, read HDMI monitor’s EDID.
n = 3, ATEN default EDID mode (Full HD 1920 x 1080
@60Hz).
n = 4, Remix mode.
[M] Enables/Disables mouse emulation.
[P] [n] [Enter] Sets the KVM switching mode.
n = 1, sets the KVM to Normal Switching Mode.
n = 2, sets the KVM to Fast Switching Mode.
Note: This hotkey will only be available with CS19208 /
CS19216’s firmware version v1.1.101 or higher.
[ ← ] Skips to the previous computer on the list, in skip mode.
[ → ] Skips to the next computer on the list, in skip mode.
[ ↑ ] Skips to the previous accessible port. If the previous
accessible port has cascaded a switch, then it skips to the
last accessible port of that switch.
[ ↓ ] Skips to the next accessible port. If the next accessible
port has cascaded a switch, then it skips to the first
accessible port of that switch.
[ESC] or
[Spacebar]
Exits hotkey setting mode.
Key Function
59
Chapter 6
Keyboard Emulation
Mac Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Mac keyboard. The emulation mappings are listed in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Mac Keyboard
[Shift] Shift
[Ctrl] Ctrl
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Alt] Alt
[Print Screen] F13
[Scroll Lock] F14
=
[Enter] Return
[Backspace] Delete
[Insert] Help
[Ctrl] F15
CS19208 / CS19216 User Manual
60
Sun Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Sun keyboard when the Control key [Ctrl] is used in conjunction with other
keys. The corresponding functions are shown in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Sun Keyboard
[Ctrl] [T] Stop
[Ctrl] [F2] Again
[Ctrl] [F3] Props
[Ctrl] [F4] Undo
[Ctrl] [F5] Front
[Ctrl] [F6] Copy
[Ctrl] [F7] Open
[Ctrl] [F8] Paste
[Ctrl] [F9] Find
[Ctrl] [F10] Cut
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Ctrl] [H] Help
Compose
-
+
61
Chapter 7
RS-232 Operation
Overview
The CS19208 / CS19216’s built-in bi-directional RS-232 serial interface
allows system control through a high-end controller or PC. RS-232 serial
operations in a CS19208 / CS19216 installation are managed via
HyperTerminal sessions on systems that are running Windows. In order to use
this feature to send commands to the CS19208 / CS19216, you must first
download and install a HyperTerminal application.
Setup
Install a HyperTerminal application on a computer that is not part of the
installation, which will be used to control the switch via the RS-232
connection. HyperTerminal applications can be download from the Internet,
and many operating systems are embedded with HyperTerminal applications.
Hardware Connection
Use a the Firmware Upgrade Cable provided with this unit to connect a
computer’s serial port to the Firmware Upgrade Port on the CS19208 /
CS19216’s front panel, as shown below:
Note: The unit used in the diagram below is CS19216, the procedure for
connecting CS19208 is identical with fewer KVM ports.
Firmware Upgrade Cable
CS19208 / CS19216 User Manual
62
RS-232 Pin Assignments
Pin assignments for the CS19208 / CS19216’s Firmware Upgrade Port that is
used for connecting to a serial terminal are given in the table, below:
Pin Assignment
1 TXD: Transmit Data
RJ-11 Female
2 RXD: Receive Data
3N/A
4 GND: Signal Ground
14
Chapter 7. RS-232 Operation
63
Console Login - HyperTerminal
Once a physical connection from the computer to the CS19208 / CS19216 has
been made, you can establish a HyperTerminal session using the instructions
below.
1. Open the HyperTerminal application, and configure the port settings for
COM1 port, then click OK.
Bits per Second: 19200, Data Bits: 8, Parity: None, Stop bits: 1, Flow Control:
None.
2. After configuring the port settings you must enable serial control on the
switch by typing the command: Open + [Enter].
CS19208 / CS19216 User Manual
64
RS-232 Commands
After you login via HyperTerminal (see Console Login - HyperTerminal) use
the instructions below to send RS-232 commands to control the switch from the
computer.
When RS-232 control is enabled via the Open + [Enter] command, the
CS19208 / CS19216’s front panel pushbuttons, OSD, hotkeys, and remote
control commands will be disabled - until the RS-232 control is disabled.
Verification
After entering a command, a verification message appears, as shown below, at
the end of the command line, as follows:
With all commands in the sections that follow:
Each command string can be separated with a space.
The [Enter] command can be replaced with the ASCII code: 0x0D0A
Response Message Description
Command OK Command or parameter is correct.
Command incorrect Command or parameter is incorrect.
Chapter 7. RS-232 Operation
65
Login
The Login command allows you to login to the CS19208 / CS19216 and begin
sending RS-232 commands. When you login the RS-232 link is “opened”, and
the CS19208 / CS19216 will not respond to front panel pushbuttons, hotkeys,
OSD, or remote control commands - until the RS-232 link is closed (see Switch
Port, page 69).
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + Name + Number + [Enter]
Parameters:
Login Command
The available formula for the Login command is as follows:
1. Command + Control + Name + Number + [Enter]
For example, to login via username and password, type the following:
login u administrator p12345 [Enter]
Command Description
login Login command
Control Description
U Input user name + password
Name Description
xxxxxxxxxxxxx The login user name
Password Description
xxxxxxxxxxxxx The login user password
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
66
Logout
The Logout commands allows you to logout of the CS19208 / CS19216 and
close the RS-232 link.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + [Enter]
Parameters:
Logout Command
The available formula for the Logout command is as follows:
1. Command + [Enter]
For example, to logout of the CS19208 / CS19216, type the following:
logout [Enter]
Command Description
logout Logout command
Enter Description
Enter Enter and send out command
Chapter 7. RS-232 Operation
67
Open / Close RS-232 Link
The Open and Close RS-232 Link commands allows you to open/close the link
between the computer sending RS-232 commands and the CS19208 /
CS19216. When the link is open, the CS19208 / CS19216 only accepts RS-232
commands and will not respond to front panel pushbuttons, OSD, hotkeys, and
remote control commands - until the link is closed. The link opens when you
login and closes after 2 minutes if no command is sent.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + [Enter]
Parameters:
Open/Close RS-232 Link Commands
The available formulas for the Open/Close RS-232 Link commands are as
follows:
1. Command + [Enter]
For example, to open the RS-232 link between the computer and CS19208 /
CS19216, type the following:
open [Enter]
2. Command + [Enter]
For example, to close the RS-232 link between the computer and CS19208 /
CS19216, type the following:
close [Enter]
Command Description
open Open RS-232 Link command
close Close RS-232 Link command
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
68
Set Baud Rate
The Set Baud Rate command allows you to configure the baud rate setting for
the serial port connection. The default baud rate is 19200.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
Set Baud Rate Commands
The available formulas for the Set Baud Rate commands are as follows:
1. Command + Control + [Enter]
For example, to set the baud rate to 19200, type the following:
baud 19200 [Enter]
2. Command + Control + [Enter]
For example, to set the baud rate to 38400, type the following:
baud 38400 [Enter]
Command Description
baud Baud Rate Command
Control Description
19200 Set baud rate to 19200 (Default)
38400 Set baud rate to 38400
9600 Set baud rate to 9600
Enter Description
Enter Enter and send out command
Chapter 7. RS-232 Operation
69
Switch Port
The Switch Port command allows you to switch ports. The default port is 01.
Use the Formula - to set Parameters - to create a Command.
Formula:
Command + Control + [Enter]
Parameters:
Switch Port Commands
The available formula for the Switch Port command is as follows:
1. Command + Control + [Enter]
For example, to switch to port 2, type the following:
sw i02 [Enter]
Note: The Control command can be skipped and the default value will be
used.
Command Description
sw Switch Port Command
Control Description
ixx Input Port Number
xx= 01~08 (CS19208); 01~16 (CS19216)
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
70
Hotkey Setting
The Hotkey Setting command allows you to change the hotkey used to invoke
the HSM (Hotkey Setting Mode). The default hotkey is [Num Lock] + [-].
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
Hotkey Setting Commands
The available formulas for Hotkey Setting commands are as follows:
1. Command + Control + [Enter]
For example, to change the HSM invoke key to [Num Lock] + [-], type the
following:
hotkey num [Enter]
2. Command + Control + [Enter]
For example, to change the HSM invoke key to [Ctrl] + [F12], type the
following:
hotkey f12 [Enter]
Command Description
hotkey Hotkey Setting Command
Control Description
num Change the HSM invoke key to:
[Num Lock] + [-] (Default)
f12 Change the HSM invoke key to:
[Ctrl] + [F12]
Enter Description
Enter Enter and send out command
Chapter 7. RS-232 Operation
71
OSD Hotkey
The OSD Hotkey command allows you to change the hotkey used to invoke the
OSD. The default hotkey is [Scroll][Scroll].
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
Hotkey Switching Commands
The available formulas for OSD Hotkey commands are as follows:
1. Command + Control + [Enter]
For example, to change the OSD hotkey invoke key to [Scroll] [Scroll], type
the following:
osdkey scroll [Enter]
2. Command + Control + [Enter]
For example, to change the OSD hotkey invoke key to [Ctrl] [Ctrl], type the
following:
osdkey ctrl [Enter]
Command Description
osdkey OSD Hotkey Command
Control Description
scroll Change OSD hotkey invoke key to:
[Scroll] [Scroll] (Default)
ctrl Change OSD hotkey invoke key to:
[Ctrl] [Ctrl]
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
72
USB Reset
The USB Reset command allows you to reset the USB connection. The default
USB reset setting is off.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
USB Reset Command
The available formula for the USB Reset command is as follows:
1. Command + Control + [Enter]
For example, to reset the USB connection, type the following:
usbreset on [Enter]
Command Description
usbreset USB Reset Command
Control Description
on Enable USB reset connection
Enter Description
Enter Enter and send out command
Chapter 7. RS-232 Operation
73
Restore Default Settings
The Restore Default Settings command allows you to reset all of the CS19208
/ CS19216’s settings back to the default. The default setting is off.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
Restore Default Value Command
The available formula for the Restore Default Settings command is as follows:
1. Command + Control + [Enter]
For example, to restore all CS19208 / CS19216’s settings back to the default,
type the following:
reset on [Enter]
Command Description
reset Restore Default Settings Command
Control Description
on Enable restore default values
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
74
Firmware Upgrade
The Firmware Upgrade command allows you to enable the firmware upgrade
mode. The default setting is off.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control+ [Enter]
Parameters:
Firmware Upgrade Command
The available formula for the Firmware Upgrade command is as follows:
1. Command + Control + [Enter]
For example, to enable firmware upgrade mode, type the following:
upgrade on [Enter]
Command Description
upgrade Firmware Upgrade Command
Control Description
on Enable firmware upgrade mode
Enter Description
Enter Enter and send out command
Chapter 7. RS-232 Operation
75
KVM Status
The KVM Status command allows you to display read-only information about
the CS19208 / CS19216’ current configuration status. The default setting is off.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
KVM Status Command
The available formula for the KVM Status command is as follows:
1. Command + Control + [Enter]
For example, to display the CS19208 / CS19216’s configuration status, type
the following:
status on [Enter]
A message similar to the one below will then appear:
hotkey: [numlock]+[-] / [scrolllock],[scrolllock]
os setting: pc
keyboard emulation: enabled/disabled
keyboard layout: English
mouse emulation: enabled/disabled
monitor re-detection: enabled/disabled
Command Description
status KVM Status Command
Control Description
on Enable KVM status
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
76
EDID Mode
The EDID Mode command allows you to set EDID mode for the CS19208 /
CS19216.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
EDID Mode Command
The available formula for the KVM Status command is as follows:
1. Command + Control + [Enter]
For example, to set the CS19208 / CS19216’s EDID mode to ATEN default
EDID, type the following:
edid default [Enter]
Command Description
edid Set EDID Mode Command
Control Description
port1 Set to display A (DisplayPort monitor) EDID
port2 Set to display B (HDMI monitor) EDID
default Set to ATEN default EDID
remix Set to remix mode
Enter Description
Enter Enter and send out command
Chapter 7. RS-232 Operation
77
Broadcast Mode
The Broadcast Mode command allows you to set enable/disable broadcast
mode for the CS19208 / CS19216. The default setting is off.
Use the Formula - to set Parameters - to create a Command.
Formulas:
Command + Control + [Enter]
Parameters:
Broadcast Mode Command
The available formula for the KVM Status command is as follows:
1. Command + Control + [Enter]
For example, to enable the CS19208 / CS19216’s broadcast mode, type the
following:
broadcast on [Enter]
Command Description
broadcast Set Broadcast Mode Command
Control Description
on Enable broadcast mode for CS19208 /
CS19216
off Disable broadcast mode for CS19208 /
CS19216
Enter Description
Enter Enter and send out command
CS19208 / CS19216 User Manual
78
This Page Intentionally Left Blank
79
Chapter 8
The Firmware Management Utility
Introduction
The purpose of the Windows-based Firmware Management Utility is to
provide an automated process for upgrading all CS19208 / CS19216 switches
in an installation. The program comes as part of a Firmware Upgrade Package
that is specific for each device.
As new firmware versions become available, new firmware upgrade packages
are posted on our website. Check the website regularly to find the latest
information and packages.
Downloading the Firmware Upgrade Package
To download the firmware upgrade package:
1. From a computer that is not part of your KVM installation go to our
website and choose the model name that relates to your device. A list of
available firmware upgrade packages appears.
2. Choose the firmware upgrade package that you wish to install (usually the
most recent) and download it to your computer.
CS19208 / CS19216 User Manual
80
Preparation
To prepare for the firmware upgrade, do the following:
1. Use the Firmware Upgrade Cable provided with this unit to connect a COM
port on your computer to the Firmware Upgrade Port of your switch.
2. Shut down all the computers on the KVM installation.
3. From your KVM switch console, login to the OSD as the administrator
(see p. 29) and select the F4 Admin function.
4. Scroll down to Firmware Upgrades. Press [Enter], then press [Y] to
invoke Firmware Upgrade mode (see p. 41).
Or
Invoke the Firmware Upgrade mode using RS-232 command (see p. 74).
Firmware Upgrade Cable
8. The Firmware Management Utility
81
Starting the Upgrade
To upgrade the firmware:
1. Run the downloaded firmware upgrade package file either by double-
clicking the file icon, or by opening a command line and entering the full
path to it.
The Firmware Upgrade Utility welcome screen appears:
Note: The screens shown in this section are for reference only. The
wording and layout of the actual screens put up by the Firmware
Upgrade Utility may vary slightly from these examples.
2. Read and Agree to the License Agreement (enable the I Agree radio button).
CS19208 / CS19216 User Manual
82
3. Click Next to continue. The Firmware Upgrade Utility main screen
appears. The devices capable of being upgraded are listed in the Device
List panel:
4. As you select a device in the list, its description appears in the Device
Description panel.
5. Click Next to perform the upgrade.
If you enabled Check Firmware Version, the Utility compares the device's
firmware level with that of the upgrade files. If it finds that the device's
version is higher than the upgrade version, it brings up a dialog box
CS19208/CS19216 [MAIN]..
CS19208/CS19216 [MAIN]..
8. The Firmware Management Utility
83
informing you of the situation and gives you the option to continue or
cancel.
If you didn't enable Check Firmware Version, the Utility installs the
upgrade files without checking whether they are a higher level, or not.
As the upgrade proceeds, status messages appear in the Status Messages
panel, and the progress toward completion is shown on the Progress bar.
The firmware [Ver 1.0.] is not newer than the current firmware
[Ver 1.0.090] in device CS19208/CS19216 [MAIN]: 000
Continue the upgrade? [Yes/No]
CS19208 / CS19216 User Manual
84
Upgrade Succeeded
After the upgrade has completed, a screen appears to inform you that the
procedure was successful.
Click Finish to close the Firmware Upgrade Utility.
After a successful completion, the switches exit Firmware Upgrade Mode, and
reset themselves.
Upgrade Failed
If the Upgrade Succeeded screen doesn't appear, it means that the upgrade
failed to complete successfully. See the next section, Firmware Upgrade
Recovery, for how to proceed.
CS19208/CS19216 [MAIN]..
CS19208/CS19216 [MAIN]
CS19208/CS19216 [MAIN]000:OK
CS19208/CS19216 [MAIN] :000
8. The Firmware Management Utility
85
Firmware Upgrade Recovery
There are three conditions that call for firmware upgrade recovery:
When a firmware upgrade is manually aborted.
When the mainboard firmware upgrade fails.
When the I/O firmware upgrade fails.
To perform a firmware upgrade recovery, do the following:
1. Power off the switch.
2. Connect the Firmware Upgrade Cable to its Firmware Upgrade Port.
3. Slide the Firmware Upgrade Recovery Switch to the Recover position.
4. Power the switch back on and repeat the upgrade procedure.
5. After the switch has been successfully upgraded, power it off, and slide the
Firmware Upgrade Recovery Switch back to the Normal position.
6. If the switch is one of the cascaded switches, plug it back into the
installation.
7. Power the switch back on.
CS19208 / CS19216 User Manual
86
OSD Configuration Backup/Restore
The Firmware Management Utility lets you backup the current OSD
configuration of the CS19208 / CS19216, and restore it when necessary.
Storing the OSD configuration settings is useful when deploying more than one
installation that uses the same settings.
Backup
Follow these steps to store a backup file to a local computer:
1. Make sure your computer is connected to the CS19208 / CS19216.
See Preparation, page 80, and follow steps 1–3.
2. When you have selected the F4 Admin function, scroll down to OSD
Config Backup / Restore. Press [Enter], then select Enable to invoke
OSD Config Backup / Restore mode.
3. Run the Firmware Management Utility. In the dialog box, choose OSD
Configuration Backup/Restore, then click Next.
4. In the window that appears, click Connect Device.
5. In the Password field, key in a password for the file.
Note: Setting a password is optional. If you do not set one, the file can be
restored without specifying a password.
6. Click Backup.
7. When the browser asks what you want to do with the file, select Save to
disk, then save it in a convenient location.
8. The Firmware Management Utility
87
Restore
Follow these steps to restore a backup file from a local computer:
1. Do steps 1 to 3 of the previous section. See Backup, page 86.
2. Click Restore to recover an OSD configuration stored in the local
computer. If you have previously set a password for this feature, enter the
password in the provided field before clicking Restore. A confirmation
window appears; click Ye s to proceed.
3. Browse for the OSD configuration file you want to use and click Restore.
Make sure the backup file is in the local computer.
4. A confirmation window appears when the restore process is done and
successful. Click OK to close it.
CS19208 / CS19216 User Manual
88
This Page Intentionally Left Blank
89
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
To prevent damage to your installation it is important that all devices are
properly grounded.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
CS19208 / CS19216 User Manual
90
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
Do not connect the RJ-11 connector marked “UPGRADE” to a public
telecommunication network.
Appendix
91
Rack Mounting
Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflow is provided to devices in the rack.
Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer.
Do not step on or stand on any device when servicing other devices in a
rack.
Caution: Slide/rail (LCD KVM) mounted
equipment is not to be used as a shelf or a work
space.
CS19208 / CS19216 User Manual
92
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://support.aten.com
For telephone support, see Telephone Support, page vii:
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration, including operating system, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
Appendix
93
CS19208 / CS19216 Connection Tables
The following tables indicate the relationship between the number of Primary
View units and the number of computers that they control:
CS19208
(First Level) +
CS19208
(Second Level)
CS19208
(First Level) +
CS19216
(Second Level)
PVs Computers
11 - 8
28 -15
3 15 - 22
4 22 - 29
5 29 - 36
6 36 - 43
7 43 - 50
8 50 - 57
9 57 - 64
PVs Computers
11 - 8
28 -23
3 23 - 38
4 38 - 53
5 53 - 68
6 68 - 83
7 83 - 98
8 98 - 113
9 113 - 128
CS19208 / CS19216 User Manual
94
CS19216
(First Level) +
CS19208
(Second Level)
CS19216
(First Level) +
CS19216
(Second Level)
PVs Computers PVs Computers
1 1 - 16 10 72 - 79
2 16 -23 11 79 - 86
3 23 - 30 12 86 - 93
4 30 - 37 13 93 - 100
5 37 - 44 14 100 - 107
6 44 - 51 15 107 - 114
7 51 - 58 16 114 - 121
8 58 - 65 17 121 - 128
9 65 - 72
PVs Computers PVs Computers
1 1 - 16 10 136 - 151
2 16 -31 11 151 - 166
3 31 - 46 12 166 - 181
4 46 - 61 13 181 - 196
5 61 - 76 14 196 - 211
6 76 - 91 15 211 - 226
7 91 - 106 16 226 - 241
8 106 - 121 17 241 - 256
9 121 - 136
Appendix
95
Specifications
Function CS19208 CS19216
Computer
Connections
Direct 8 16
Max. 128 (via Cascade) 256 (via Cascade)
Port Selection OSD, Hotkey, Pushbutton, RS-232 Commands
Connectors Console
Ports
KB 1 x USB Type A Female
Video 1 x DisplayPort Female
1 x HDMI Female
Mouse 1 x USB Type A Female
Speakers 2 x 3.5mm Audio Jack Female (Green; 1 x front, 1 x rear)
KVM
Ports
KB /
Mouse
8 x USB3.1 Gen1 Type B
Female (Blue)
16 x USB3.1 Gen1 Type B
Female (Blue)
Video 8 x DisplayPort Female 16 x DisplayPort Female
Speakers 8 x 3.5mm Audio Jack
Female (Green)
16 x 3.5mm Audio Jack
Female (Green)
F/W Upgrade 1 x RJ11 Female (Black)
Power 1 x DC Jack
USB 3.1 Hub 2 x USB 3.1 Gen1 Type A Female (Blue; 2 x front)
Switches Port Selection 8 x Pushbutton 16 x Pushbutton
Reset 1 x Semi-recessed Pushbutton
F/W Upgrade 1 x Slide Switch
LEDs USB Link 8 (Green) 16 (Green)
On Line / Selected 8 (Orange) 16 (Orange)
Power 1 (Green)
Emulation Keyboard / Mouse USB
Video DisplayPort: 4096 x 2160 @ 60Hz
HDMI: 4096 x 2160 @ 60Hz
Scan Interval 1–255 Seconds (Default: 5 secs)
Power Consumption DC12V:18.44W:136BTU DC12V:26.66W:175BTU
Environment Operating Temp. 0–40ºC
Storage Temp -20–60ºC
Humidity 0–80% RH, Non-condensing
Physical
Properties
Housing Metal
Weight 3.11 kg (6.85 lb) 3.54 kg (7.8 lb)
Dimensions
(L x W x H)
43.24 x 21.43 x 4.40 cm
(17.02 x 8.44 x 1.73 in.)
43.24 x 21.43 x 4.40 cm
(17.02 x 8.44 x 1.73 in.)
CS19208 / CS19216 User Manual
96
Administrator Login Failure
If you are unable to perform an Administrator login (because the username/
password information has become corrupted, or you have forgotten it, for
example), you can clear the login information with the following procedure:
1. Power off the CS19208 / CS19216 and remove its housing.
2. Short the jumper labeled DEFAULT PASSWORD.
3. Power on the switch.
4. When the front panel LEDs flash, power off the switch.
5. Remove the jumper cap.
6. Close the housing and start the CS19208 / CS19216 back up.
After you start back up, you can use the default login procedure (see OSD
Login, page 29) to login.
Appendix
97
Factory Default Hotkeys and Settings
Setting Default
OSD Hotkey [Scroll Lock] [Scroll Lock]
Invoking HSM Hotkey [Number Lock] [-]
Port ID Display Position Upper Left Corner
Port ID Display Duration 3 seconds
Port ID Display Mode The Port Number plus the Port Name
Auto Scan Interval 5 seconds
Scan/Skip Mode All Ports
Mouse Emulation Enabled
Screen Blanker Disabled
Logout Timeout Disabled
EDID Mode DisplayPort Monitor’s EDID
Beeper Enabled
Accessible Ports Full for All Users on All Ports
Video DynaSync Enabled
CS19208 / CS19216 User Manual
98
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in
materials and workmanship for a Warranty Period of two [2] years (warranty
period may vary in certain regions/countries) commencing on the date of
original purchase. This warranty period includes the LCD panel of ATEN LCD
KVM switches. Select products are warranted for an additional year (see A+
Warranty for further details). Cables and accessories are not covered by the
Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty
Period. If a product is detective, ATEN will, at its discretion, have the option
to (1) repair said product with new or repaired components, or (2) replace the
entire product with an identical product or with a similar product which fulfills
the same function as the defective product. Replaced products assume the
warranty of the original product for the remaining period or a period of 90 days,
whichever is longer. When the products or components are replaced, the
replacing articles shall become customer property and the replaced articles
shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
© Copyright 2021 ATEN® International Co., Ltd.
Released: 2021-05-26
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
Index
A
Activate Beeper 41
ADM 39
Auto Scanning 45
Invoking Auto Scan 50
Pausing Auto Scan 50
Scan Duration 38
Stopping 50
B
Beeper
Activate 41
Control 52
Hotkey Control 52, 53
BRC 44
Broadcast Mode 44
C
Clear the Name List 41
Components 6
Computer Connection Tables 93
D
desktop mounting 12
E
Edit Port Names 41
F
F1: GOTO 35
F2: LIST 36
F3: SET 37
F4: ADM 39
F5: SKP 43
F6: BRC 44
F7: SCAN 45
F8: LOUT 46
Firmware upgrade
OSD setting 42
port 80
recovery 85
G
GOTO 35
H
Hot Plugging 27
Console Ports 27
KVM ports 27
Hotkey
Beeper Control 52, 53
Command Mode 38
OSD 37
Selecting the Active Port 49
Hotkey Mode
exiting 48
Hotkey Port Control 47
I
Installation
two stage 19
K
Keyboard Emulation
Mac 59
Sun 60
L
LIST 36
Logout 46
Logout Timeout 40
LOUT 46
M
mounting
desktop 12
rack 12
O
Online
Registration iii
OSD
Functions 34
Hotkey 32, 37
Logout 46
Main Screen 31, 32
Main Screen Headings 33
Navigation 33
Overview 31
Password 31
P
Password 31
Pause 45
Port ID
Display Duration 38
Display Mode 38
Display Position 37
Numbering 28
Port Names 41
Port Selection 28
CS19208 / CS19216 User Manual
Manual 28
ports
quick view 41
set operating system 42
Powering Off and Restarting 29
Q
quick view ports 41
R
Rack Mounting
Safety information 91
rack mounting 12
front 13
rear 15
Requirements
Operating Systems 5
OS Support 5
Restore Default Values 41
RoHS ii
S
Safety Instructions
General 89
Rack Mounting 91
SCAN 45
Scan Duration 38
SCAN/SKIP MODE 38
Screen Blanker 38
Selecting the Active Port 49
SET 37
Accessible Ports 40
Logout Timeout 40
Quick View Ports 41
Skip Mode 43, 51
Specifications 94
stacking 12
T
Technical Support 92
Telephone support iii
Timeout 40
Two Stage Installation 19
U
User Notice iii