Table of Contents
ATEN IC485S-AT-E User Manual
Displayed below is the user manual for IC485S-AT-E by ATEN which is a product in the Signal Converters category. This manual has pages.
Related Manuals
FCC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply
with the limits for a Class B digital service, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the
user’s authority to operate this equipment. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
KCC Statement
RoHS
This product is RoHS compliant.
- 3 -
IC485S /IC485SI User Manual
Online Registration
You can register your product at our online support center:
Online Support
International
North America
International http://support.aten.com
Email Support support@aten.com
Online
Support
Technical Support http://support.aten.com
Troubleshooting
Documentation
Software Updates
http://www.aten.com
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software
Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
1-949-428-1111
- 4 -
Telephone Support
For telephone support, call this number:
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
- 5 -
Package Contents
The RS232 / RS485 Interface Converter package contains the
following items:
IC-485S or IC-485SI Interface Converter
1 Power Adapter (DC 9V; 300mA)
1 User Manual*
Check to make sure that all the components are present and that
nothing got damaged in shipping. If you encounter a problem,
contact your dealer.
Read this manual thoroughly and follow the installation and
operation procedures carefully to prevent any damage to the unit,
and/or any of the devices connected to it.
*Features may have been added to the IC485S /IC485SI since
this manual was printed. Please visit our website to download
the most up-to-date version of the manual.
Copyright © 2015-2020 ATEN
®
International Co., Ltd.
Manual Part No. PAPE-0075-202G
Manual Date: 2020-11-16
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights
reserved. All other trademarks are the property of their respective owners.
- 6 -
Overview
Although RS-232 serial ports are found on almost every
computer, because of their slow transmission speeds, limited
range, and limited networking capabilities, they are not an
effective solution for industrial strength long distance
communications systems.
Systems based on the RS-485 standard, however, utilize
different voltage lines for the data and control signals, so they are
not subject to the RS-232 limitations.
The IC-485S / IC-485SI is a bidirectional converter that
transparently converts RS-232 signals to RS-485 signals (and
vice versa). The IC-485S / IC-485SI provides Point-to-Point;
Multidrop; and Simplex operations over distances of up to 1200
m (4000 ft.), thus permitting the creation of reliable long distance
data communications systems using standard computer
hardware.
- 7 -
Switch Configuration
The IC-485S / IC-485SI’s operating mode parameters are set
with two slide switches:
SW1 sets the Device Mode
SW2 sets the Transmitting and Receiving Mode
IC-485S Switch Settings
Position
Setting
SW1 SW2
1DCETxO, RxON
2 DTE TxRTS, RxRTS
3 Monitor TxRTS, RxON
Spare
Power Jack
RJ-11
Terminal Block
SW 1
SW 2 RS-232 DB-25 Female Connecter
- 8 -
IC-485SI Switch Setting
Position
Setting
SW1 SW2
1DCETxO, RxON
2 DTE TxRTS, RxRTS
3XTxRTS, RxON
Power Jack
Grnd. Tab
T
erminal Block
SW 1
SW 2 RS-232 DB-25 Female Connect
er
- 9 -
Terminology
Explanations of the SW! and SW2 terms are given in the table
below:
Term Explanation
DCE Data Communications Equipment; if the IC-485S /
IC-485SI is going to be plugged into a DTE
device, the IC-485S / IC-485SI must be set to
DCE.
DTE Data Terminating Equipment; if the IC-485S / IC-
485SI is going to be plugged into a DCE device,,
the IC-485S / IC-485SI must be set to DTE.
TxON,, RxON This setting is used in Point-to-Point operations,,
in which the unit is always in Transmitting and
Receiving Mode.
TxRTS, RxRTS This setting is used in Multidrop operations, in
which the unit is in Transmitting Mode when the
RTS signal is high, and is in Receiving Mode
when the RTS signal is low.
TxRTS, RxON This setting is used in Multidrop Full Duplex
operations to monitor the RS-485 line signals.
Receiving Mode is always ON. Transmitting mode
only occurs when the RTS signal is high.
- 10 -
Operating Modes
The IC-485S / IC-485SI supports four operating modes: Point-to-
Point; Multidrop; Simplex; and Monitor (IC-485S only). Point-to-
Point and Multidrop can be configured for Full or Half Duplex.
Each of the operating modes is explained in the sections that
follow.
Point-to-Point
A Point-to-Point configuration is one in which two devices,
located at two different places are linked for communication by a
pair of IC-485S or IC-485SI units. There are two configurations:
Point-to-Point Full Duplex, and Point-to-Point Half Duplex.
1. Point-to-Point Full Duplex
Point-to-Point Full Duplex uses reverse four wire cabling
as shown in the diagram below:
For both IC-485S / IC-485SI units, set SW1 to DCE or DTE
depending on what type of device the IC-485S / IC-485SI
will plug into (if it will plug into a DCE device, configure it
for DTE, and vice versa).
For both IC-485S / IC-485SI units, set SW2 to TxON,
RxON.
T+
T-
R-
R+
R+
R-
T-
T+
Connect
to PC#1's
COM port
Connect
to PC#2's
COM port
DB-25 DB-25
- 11 -
2. Point-to-Point 2 Wire Half Duplex
Point-to-Point Half Duplex uses straight through four wire
cabling, as shown in the diagram below:
For both IC-485S / IC-485SI units, set SW1 to DCE or DTE
depending on what type of device the IC-485S / IC-485SI
will plug into (if it will plug into a DCE device, configure it
for DTE, and vice versa).
For both IC-485S / IC-485SI units, set SW2 to TxRTS,
RxRTS.
Note: The RTS signal is controlled by an external software
command. The IC-485S / IC-485SI has no capability to
control this signal by itself
T+
T-
R-
R+
R+
R-
T-
T+
Connect
to PC#1's
COM port
Connect
to PC#2's
COM port
DB-25 DB-25
- 12 -
Multidrop
A Multidrop configuration is one in which more than two devices
are linked for communication using several IC-485S / IC-485SI
units.
One of the devices that one of the IC-485S / IC-485SIs connects
to is designated as the Primary device. All the remaining devices
that the rest of the IC-485S / IC-485SIs connect to are designated
as Secondary devices. There are two configurations: Multidrop
Full Duplex, and Multidrop Half Duplex.
1. Multidrop 4 Wire Full Duplex
Multidrop Full Duplex uses reverse four wire cabling to link
all the connected IC-485S / IC-485SI units:
For all IC-485S / IC-485SI units, set SW1 to DCE or DTE
depending on what type of device the IC-485S / IC-485SI
will plug into (if it will plug into a DCE device, configure it
for DTE, and vice versa).
For the Primary unit, set SW2 to TxON, RxON.
For all Secondary units, set SW2 to TxRTS, RxON.
Primary
T+
T
-
R
-
R+
Secondary 1
R+
R -
T -
T+
Secondary 2
R+
R -
T -
T+
.
.
.
Secondary 31
PC1
COM1/
COM2
PC2
COM1/
COM2
PC3
COM1/
COM2
- 13 -
2. Multidrop Half Duplex
Multidrop Half Duplex uses straight-through four wire
cabling, to link all the connected IC-485S / IC-485SI units:
For all IC-485S / IC-485SI units, set SW1 to DCE or DTE
depending on what type of device the IC-485S / IC-485SI
will plug into (if it will plug into a DCE device, configure it
for DTE, and vice versa).
For all IC-485S / IC-485SI units set SW2 to TxRTS,
RxRTS.
Note: The RTS signal is controlled by an external software
command.The IC-485S / IC-485SI has no capability to
control this signal by itself.
Primary
T+
T
-
R
-
R+
Secondary 1
R+
R -
T -
T+
Secondary 2
R+
R -
T -
T+
PC1
COM1/
COM2
PC2
COM1/
COM2
PC3
COM1/
COM2
Secondary 3
R+
R -
T -
T+
.
.
Secondary 31
PC4
COM1/
COM2
- 14 -
Simplex
A Simplex configuration is one in which more than two devices
are linked for communication using several IC-485S / IC-485SI
units in a manner similar to Multidrop. The difference is that in a
Simplex configuration, the Primary device can only talk, and the
Secondary devices can only listen.
Simplex uses reverse two wire cabling to link all the
connected IC-485S / IC-485SI units, as shown in the figure
below:
For all IC-485S / IC-485SI units, set SW1 to DCE or DTE
depending on what type of device the IC-485S / IC-485SI
will plug into (if it will plug into a DCE device, configure it
for DTE, and vice versa).
For all of the units (Primary and Secondary), set SW2 to
TxON, RxON.
Primary
T+
T
-
R
-
R+
Secondary 1
R+
R -
T -
T+
Secondary 2
R+
R -
T -
T+
Secondary 3
R+
R -
T -
T+
:
:
Secondary 31
PC1
COM1/
COM2
PC2
COM1/
COM2
PC3
COM1/
COM2
PC4
COM1/
COM2
- 15 -
Monitor IIX-485S Only!
With Monitor Mode, the RS-485S can be wired to the lines of an
RS-485 or RS-422 device to monitor the line signals. In this
configuration, the RS-485S changes the functions of T+ and T- to
R’+ and R’- respectively.
Set SW1 to Monitor.
Set SW2 to TxRTS, RxON
Note: 1. The RTS must be Low in Monitor Mode.
2. The R+ and R- signals are converted and linked to the
RS-232 port, DB-25 pin 3. The R’+ and R’- (T+ and T-)
signals are converted and linked to the RS-232 port,
DB-25 pin 2.
Device 1
T+
T
-
R-
R+
Device 2
R+
R-
T-
T+
IC-485S
T+ (R'+)
T- (R'-)
R-
R+
PC
COM1/
COM2
- 16 -
Installation
1. Set each IC-485S / IC-485SI’s configuration switches
according to the information provided in the Switch
Configuration and Operating Modes sections.
2. Plug the IC-485S / IC-485SI’s DB-25 female connector into
the computer’s RS-232C port.
3. Connect the IC-485S / IC-485SI units to each other:
Use two or four wire twisted pair cable in a reverse or
straight through configuration according to the information
provided in the Switch Configuration and Operating Modes
sections.
For the IC-485S, you may use either the RJ-11 telephone
socket, or wire directly to the Terminal Block (See the
Terminal Block section for pin assignment details).
For the IC-485SI, you must ground the device by
connecting a grounding wire from the Grounding Tab to the
grounding source.
Note: 1. When tightening the terminal connector screws it is
recommended to use a Phillips PH1 Screwdriver.
2. Over-tightening the terminal connector screws may
result in damage to your IC-485S or IC-485SI and
difficulty loosening the screws.
4. Power on the computers. The units are now ready for
operation.
- 17 -
Appendix
The Terminal Block
The four screw terminal block has different pin assignments
depending on the operating mode:
In DCE/DTE mode, terminals 1 (+V) and 2 (-V) are configured
to transmit data (the transmitter); while terminals 3 (-V) and 4
(+V) are configured to receive data (the receiver).
In Monitor mode (IC-485S only), terminals 1 and 2 are,
respectively, the positive and negative of receiver 1; while
terminals 3 and 4 are, respectively, the positive and negative
of receiver 2.
Pin DCE/DTE Monitor
1 Transmitter +V Receiver 1 +V
2 Transmitter -V Receiver 1 -V
3 Receiver -V Receiver 2 -V
4 Receiver +V Receiver 2 +V
- 18 -
DCE / DTE Connection Table
Because of the polarity of the communication signals, a DTE
configured device must connect to a DCE configured device. The
shaded area in the figure below is an example of a DTE to DCE
connection:
Self Test
To test the internal circuit of the interface converter, connect a
dumb terminal to the unit and do the following:
1. Set SW1 to DCE (if the dumb terminal is configured for DCE).
2. Set SW2 to TxON, RxON.
3. Connect a wire from pin 1 (Tx+) to pin 4 (Rx+)
4. Connect a wire from pin 2 (Tx-) to pin 3 (Rx-)
5. Set the terminal to full duplex and enter data.
If the data displays on the screen, the internal circuit is
operational.
DCE
DB-9
2
3
8
7
4
6
5
DTE
DB-9
3
2
7
8
6
4
5
DCE
DB-25
3
2
5
4
20
6
7
DTE
DB-25
2
3
4
5
6
20
7
DCE
DB-25
2
3
4
5
6
20
7
DTE
DB-25
3
2
5
4
20
6
7
Tx Rx
Rx Tx
RTS CTS
CTS RTS
DSR DTR
DTR DSR
GND
Cable
25/25 or
9/25 pin
IC-485ASIDevice's Connector Pin #
- 19 -
Troubleshooting
Problem Action
Data Transmission
Failure
Check that the power adapter is plugged in
and working properly.
Check that the IC-485S / IC-485SI units are
securely plugged into the computers’ serial
ports.
Check that the cables are properly set up and
properly connected.
Check that SW1 and SW2 are set properly.
Data Loss or Error Check that the Data Rate and Data Format
are the same for all devices.
- 20 -
Limited Warranty
ATEN warrants its hardware in the country of purchase against
flaws in materials and workmanship for a Warranty Period of two
[2] years (warranty period may vary in certain regions/countries)
commencing on the date of original purchase. This warranty
period includes the LCD panel of ATEN LCD KVM switches.
Select products are warranted for an additional year (see A+
Warranty for further details). Cables and accessories are not
covered by the Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the
Warranty Period. If a product is detective, ATEN will, at its
discretion, have the option to (1) repair said product with new or
repaired components, or (2) replace the entire product with an
identical product or with a similar product which fulfills the same
function as the defective product. Replaced products assume the
warranty of the original product for the remaining period or a
period of 90 days, whichever is longer. When the products or
components are replaced, the replacing articles shall become
customer property and the replaced articles shall become the
property of ATEN.
To learn more about our warranty policies, please visit our
website:
http://www.aten.com/global/en/legal/policies/warranty-policy