Table of Contents
- IP8000 User Manual
- User Information
- Package Contents
- Introduction
- Hardware Setup
- Browser Login
- Administration
- The Windows Client
- The Java Applet
- The Log File
- The Log Server
- AP Operation
- Appendix
ATEN IP8000-AT-G User Manual
Displayed below is the user manual for IP8000-AT-G by ATEN which is a product in the Interface Cards/Adapters category. This manual has pages.
Related Manuals
Remote Management PCI Card
IP8000
User Manual
www.aten.com
ip8000.book Page i Friday, May 9, 2008 10:39 AM
IP8000 User Manual
ii
FCC Information
This is an FCC Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
RoHS
This product is RoHS complian t.
SJ/T 11364-2006
The following contains information that relates to China.
ip8000.book Page ii Friday, May 9, 2008 10:39 AM
IP8000 User Manual
iii
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modi fications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage settin g was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
International http://support.aten.com
North America ATEN TECH http://www.aten-usa.com/product_registration
ATEN NJ http://support.aten.com
International 886-2-8692-6959
North America ATEN TECH 1-888-999-ATEN
ATEN NJ 1-732-356-1703
ip8000.book Page iii Friday, May 9, 2008 10:39 AM
IP8000 User Manual
iv
Package Contents
The IP8000 package consists of:
1 IP8000 Remote Management PCI Card
1 Custom KVM Cable Set
1 Feature Cable
1 Power Adapter
1 Software CD
1 User Manual*
1 Quick Start Guide
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual tho rou ghly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
*Features may have been added to the IP8000 since this manual was printed.
Please visit our webs i te to do w nl oad the most up-to- date version of the
manual.
© Copyright 2007 ATEN® International Co., Ltd.
Manual Part No. PAPE-0279-100G
Printing Date: 12/2 007
P/N: IP8000 ATFW Series
A
TEN and the ATEN lo go are registered trademar ks of ATEN International Co., Lt d. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
ip8000.book Page iv Friday, May 9, 2008 10:39 AM
IP8000 User Manual
v
Contents
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
1. Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Virtual Media Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
IP8000 Layout Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2. Hardware Setup
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Basic Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Feature Cable Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3. Browser Login
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Screen Elements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Utility Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Administration Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Remote Console Preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4. Administration
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Access Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
DNS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Finishing Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
ip8000.book Page v Friday, May 9, 2008 10:39 AM
IP8000 User Manual
vi
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
IP Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
MAC Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ANMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
RADIUS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
RADIUS Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
CC Management Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Log Server Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
User Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Customization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5. The Windows Client
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
The Windows Client Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Hotkey Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Configuring the Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Video Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Virtual Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Message Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
The Button Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Compose Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Message Display Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
User List Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6. The Java Applet
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
The Java Applet Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Hotkey Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Configuring the Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Video Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Message Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Ctrl+Alt+Del. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Lock LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
7. The Log File
The Log File Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
ip8000.book Page vi Friday, May 9, 2008 10:39 AM
IP8000 User Manual
vii
8. The Log Server
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
The Menu Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Configure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
The Log Server Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
The List Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
The Tick Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
9. AP Operation
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
The AP Windows Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
The Windows Client Conn ection Screen. . . . . . . . . . . . . . . . . . . . . . .67
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
The Administrator Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
ANMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
User Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Upgrading the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
The AP Java Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Starting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
The Java Client Connection Screen . . . . . . . . . . . . . . . . . . . . . . . . . .78
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
ip8000.book Page vii Friday, May 9, 2008 10:39 AM
IP8000 User Manual
viii
IP Address Determination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Resetting Your Computer Address . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
The Windows Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Administrator Login Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
The Windows Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
The Java Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
The Log Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Sun Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Additional Mouse Synchronization Procedures . . . . . . . . . . . . . . . . . . . . 89
Windows:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Sun / Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Trusted Certificates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Installing the Certificate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Certificate Trusted. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
ip8000.book Page viii Friday, May 9, 2008 10:39 AM
IP8000 User Manual
ix
About this Manual
This User Manual is provided to help you get the most from your IP8000. It
covers all aspects of installation, configuration and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the IP8000. Its purpose,
features and benefits are presented, and its components are described.
Chapter 2, Hardware Setup, provides step-by-step instructions for
connecting up your installation.
Chapter 3, Browser Login, describes how to log into the IP8000 with a
browser, and explains the functions of the icons and buttons that appear on the
opening web page.
Chapter 4, Administration, explains the administrative procedures that are
employed to configure the IP8000’s working environ men t.
Chapter 5, The Windows Client, explains how to connect to the IP8000
with the browser-based Windows Client software, and describes how to use the
OSD to access and control the server that the card is installed in.
Chapter 6, The Java Applet, describes how to connect to the IP8000 with
the Java Applet software, and explains how to use the OSD to access and
control the server that the card is installed in.
Chapter 7, The Log File, shows how to use the log file utility to view the
events that take place on the IP8000.
Chapter 8, The Log Server, explains how to install, configure, and use, the
Log Server
Chapter 9, AP Operation, describes how to config ure and operate the
IP8000 using the stand-alone Windows and Java AP programs, instead of th e
browser.
An Appendix, at the end of the manual provides technical and
troubleshooting in formation.
ip8000.book Page ix Friday, May 9, 2008 10:39 AM
IP8000 User Manual
x
Conventions
This manual uses the following conven tions:
Product Information
For information about all ATEN products and how they can help you connect
without limits, vi si t ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a li st of locations and telephone numbers:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start → Run means to
open the Start menu, and then select Run.
Indicates critical information.
International http://www.aten.com
North America ATEN TECH http://www.aten-usa.com
ATEN NJ http://www.aten.com
ip8000.book Page x Friday, May 9, 2008 10:39 AM
1
Chapter 1
Introduction
Overview
The IP8000 is a PCI card implementation of a control unit that provides “over-
IP” access and control of the server it is installed in. In addition to local console
operation, the IP8000 allows multi-platform access and control of the server
from remote locations using a standard Internet browser or with a stand-alone
Windows-based application.
The IP8000 installs in any available PCI slot, then connects to the Internet, an
Intranet, LAN, or WAN using industry standard Category 5 cable. Because the
IP8000 uses TCP/IP for its communications protocol, the server it is connected
to can be accessed from any computer on the Net - whether that computer is
located down the hall, down the street, or half-way around the world.
For ease of operation, a user-friendly Windows GUI Client and a Java Applet
are available in browser-based versions. A stand-alone Windows application
version is provided, as well. Inclusion of the Java applet ensures that the
IP8000 is platform independent, and is able to work with all operating systems.
Operators at remote locations connect to the IP8000 via its IP address. Once a
connection has been established and au thorization granted, remote users can
exchange keyboard, video and mouse signals with the server just as if they
were physically present and working on the equipment directly.
Administrator utilities are provided to configure the system; limit access from
remote comput ers; manage users; and maintain the sy st em with firmware and
software module updates. In addition, a Log Server records all the events that
take place on the IP8000 for the administrator to analyze.
System administrators can handle a multitude of tasks with ease - from
installing and running GUI applications, to BIOS level troubleshooting, routine
monitoring, maintenance, system administration, reb ooting and even pre-
booting functions.
Your IP8000 investment is protected by a Firmware Upgrade Utility. You can
stay current with the latest functionality improvemen ts by downloading
firmware update files from our website as they become available, and then
using the utility to quickly and con veni en tly pe rform the upgrade.
ip8000.book Page 1 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
2
Features
Standard PCI-sized card provides over-IP access and control of a remote
server from anywhere in the world
Virtual medi a via USB 2.0 data transmission
Remote power control and reset suppo rt
Up to 64 user accounts – Up to 32 concurrent user login s for single-bus
sharing
Message board feature allows logged in users to communicate with each
other, and allows a user to take exclusive control of the KVM functions
External authentication support: RADIUS
Web-based Wi ndows and Java implementations allow th e server to be
controlled from any browser.
Windows GUI and Java client software for non-browser access – the Java
client works with practically all operating systems
Supports TCP/IP, HTTP, HTTPS, UDP, DHCP, SSL, ARP, DNS, ICMP,
CHAP
Supports 10Base-T, 100Base-T
Superior video resolution: up to 1600 x 120 0 @ 60Hz; 24-bit color depth
for remote sessions
Bandwidth optimizatio n via grayscale and video quality setting
Advanced security features include password protection and adv a nced
encryption technologies
Secure 128-bit SSL encryption
Enable/disable browser operation
Three level authentication: M ulti- Administrators, Users, Viewers
Event logging
Remote firmware upgrad ing
Host-side OS support: Windows 2000/2003/XP/NT; Redhat 7.1 and
above; FreeBSD, Novell
ip8000.book Page 2 Friday, May 9, 2008 10:39 AM
1. Introduction
3
System Requirements
General
For best results we recommend that the computers used to access the
IP8000 control unit have at least a P III 1 GHz processor, and that the
screen resolution is set to 1024 x 768.
Browsers must support 128-bit SSL data encrypti on.
For best results we recommend that the internet connection speed be at
least 128 kbps.
For the browser-based Java Applet and AP Java Client, you must have
Sun's Java Runtime Environment (JRE) 6, Update 3, or higher.
For the Log Server, you must have the Microsoft Jet OLEDB 4.0 or higher
driver installed.
Video
Only non-interlaced video signals at the following resolutio ns and refresh
rates are supported:
Resolution Refresh Rate s
640 x 480 60, 72, 75, 85, 90, 100, 120
720 x 400 70, 75
800 x 600 56, 60, 72, 75, 85, 90, 100, 120
1024 x 768 60, 70, 75, 85, 90, 100
1152 x 864 60, 70, 75, 85
1280 x 1024 60, 70, 75
1600 x 1200 60
ip8000.book Page 3 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
4
Cables
Two cable sets are provided with this package: a KVM cable set to link the
IP8000 to a server; and a feature cable to link the IP8000 to the mainboard
power control header.
Note: Only cable sets specifically designed to work with the IP8000 may
be used for the above purposes.
Cat 5 or higher cable should be used to connect the IP8000 to the LAN,
WAN, or Internet.
Operating Systems
Supported operating systems are shown in the table, below:
Virtual Media Support
USB CDROM Drives
USB Floppy Drives
USB Flash Drives
IDE CDROM Drives
Image Files
OS Version
Windows 2000 and higher
Linux RedHat 7.1 and higher
SuSE 8.2 and higher
Mandriva (Mandrake) 9.0 and higher
UNIX AIX 4.3 and higher
FreeBSD 4.2 and higher
Novell Netware 5.0 and higher
ip8000.book Page 4 Friday, May 9, 2008 10:39 AM
1. Introduction
5
IP8000 Layout Diagram
No. Component Description
1. Monitor Port The video cable from your monitor plugs in here
2. LAN Port The cable that connects to the WAN, LAN, Intranet, or
Internet plugs in here.
3. KVM Port The Custom KVM cable that links the card to your server’s
Video and USB ports plugs in here.
4. Power Jack The power adapter cable plugs in here.
Note: Use of the power adapter is optional. If it is not used,
however , you will be unable to perform a remote Power On.
5 Feature Cable
Connector The feature cable plugs in here. See Feature Cable
Installation, page 9 for details.
1
2
3
4
5
ip8000.book Page 5 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
6
This Page Intentionally Left Blank
ip8000.book Page 6 Friday, May 9, 2008 10:39 AM
7
Chapter 2
Hardware Setup
Before You Begin
Basic Installation
After installing the IP8000 into any available PCI sl ot on the server’s
mainboard, refer to the installation diagram below (the diagram num bers
correspond to the step numbers), and do the following:
1. Plug the local monitor cable into th e IP8000's video port.
2. Plug the local keyboard and mouse into the server’s keyboard and mouse
ports.
Note: The installation diagram depicts a PS/2 Mouse and Keyboard. If you
use USB mice and keyboards, plu g them into USB port s.
1. Make sure that the power to any device that you connect to the
installation has been turned off. You must unpl ug the power
cords of any computers that have the Keyboard Power On
function.
2. Avoid Electrostatic Discharge (ESD). Keep your IP8000 card in
its antistatic bag until it is ready to be installed. Avoid contact
with any component or connector on any adapter card, printed
circuit board, or memory module. Handle these components by
the mounting bracket.
3. Perform all unpacking and installati on procedures on a ground
connected antistatic mat. Wear an antistatic wristband grounded
at the same point as the antistatic mat. You can also use a sheet
of conductive aluminum foi l grounded through a one megaohm
resistor instead of the antistatic mat. Similarly, a strip of
conductive aluminum foil wrapp ed around the wrist and
grounded through a one mega ohm resistor serves the same
purpose as a wristband.
ip8000.book Page 7 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
8
3. Use the KVM Cable provided with this package to connect the IP8000's
KVM port to the server’s video port and USB port.
4. Plug the LAN or WAN cable into the IP800 0's LAN port.
5. Plug the power adapter cable into the IP80 00's power jack, then plug the
power adapter into an AC power source.
Note: Use of a power adapter is optional. If a power adapter isn’t used,
however, you will not be able to perform a remote Power On.
Note: Although the IP8000 plugs into a server’s PCI slot, it has its own
environment and operates independent ly of the server it resides on –
using its I/O ports to link to the server it co ntrols. It can even li nk to
(with steps 2 and 3), and control, a server other than the one it actually
resides on.
2
1
3
4
5
ip8000.book Page 8 Friday, May 9, 2008 10:39 AM
2. Hardware Setup
9
Feature Cable Installation
The feature cable provides the ability to perform remote power on/off and reset
operations. The cable plugs into a header block located at the upper right of the
card. The block contains two rows of pins. The upper row comprises pins 1, 3,
5, and 7; the lower row comprises pins 2, 4, 6, and 8. To install the feature
cable, do the following:
1. Plug the feature cable’s large connector (the one containing all 4 wires)
into to the lower row of pins (pins 2–8) with the white wire at the top; the
orange wire at the bottom.
2. Unplug the leads from the computer mainboard’ s Reset pin header. (These
are the ones coming from the computer case’s Reset switch).
3. Plug the feature cable connector containing the white and blue wires into
the mainboard’s Reset pin header.
4. Unplug the leads from the computer mainboard’s Power pin header.
(These are the ones coming from the computer case’s Power switch).
5. Plug the feature cable connector containing the white and orange wi res
into the computer mainbo ard’s Power header.
(Continues on next page.)
White
Blue
White
Orange
W
B
W
O
To Mainboard
Reset Header
To Mainboard
Power Header
2
4
6
8
ip8000.book Page 9 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
10
(Continued from previous page.)
6. Plug the leads from computer case’s Reset switch into pins 1–3 (on the
upper row) of the IP8000’s feature cable pin header.
7. Plug the leads from the computer case’s Power switch into pins 5–7 (on
the upper row) of the IP8000’s feature cable pin header.
Note: It is not necessary to pay attention to the plug alignment (i.e., which
wire is aligned with which pin) when you plug the leads from the feature
cable into the mainboard headers, or when you plug the leads from the
case into the feature cable header.
From Case
Reset Switch
From Case
Power Switch
1
3
5
7
ip8000.book Page 10 Friday, May 9, 2008 10:39 AM
11
Chapter 3
Browser Login
The IP8000 can be accessed either from an internet type browser, or via
stand-alone Windows and Java applications. The next several chapters
describe bro wser-based operations. Stand-alone AP operation is discussed in
Chapter 9.
Logging In
To operate the IP8000 from an Internet browser, begin by logging in:
1. Open your browser and specify the IP address of the IP8000 you want to
access in the browser's URL location bar.
Note: 1. For security purposes, a login string may have been set by the
administrator. If so, you must include a forward slash and the
login string along with the IP address when you log in. For
example:
192.168.0.100/ip8k
If you don't know the IP address and login string, ask your
Administrator.
2. If you are the administrator, and are logging in for the first time,
the various ways to determine the IP8000's IP address are
described in the Appendix on page 83.
(Continues on next page.)
ip8000.book Page 11 Friday, May 9, 2008 10:39 AM
Chapter 3. Browser Login
13
The IP8000 login page appears:
3. Provide a valid Username and Password (set by the IP8000 administrator),
then Click Login to continue.
Note: 1. If you are the administrator, and are logging in for the first time,
use the default Username: administrator; and the default
Password: password. For security purposes, we strongly
recommend you remove these and give yourself a unique
Username and Password (see User Management, page 27).
2. If you supplied an invalid login, the login entry boxes will
become blank. Log in again being careful to specify a valid
Username and Password.
ip8000.book Page 13 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
14
After you have successfully logged in, the IP8000 Main Screen appears:
Screen Elements
The Main Screen consists of Utility icon s arranged vertically down the left
side; Administration icons arranged across the top; and a Remote Console
Preview with icons to launch the Java Applet and Windows Client displayed in
the center.
Note: If a user doesn’t have permission to perform a particular activity, the
icon for that activity doesn’t appear. See User Management, page 27,
for permission details.
(Continues on next page.)
ip8000.book Page 14 Friday, May 9, 2008 10:39 AM
Chapter 3. Browser Login
15
(Continued from previous page.)
Utility Icons
The icons arranged down the left side perform the foll owing functions:
Administration Icons
The icons arranged across the top of the page are linked to the adm ini stration
utilities, which are used to configure th e IP8000. The ability to make
configuration changes depends on the permissions associated with a user’s
login information (see User Management, page 27). The admi nistrative
functions are discussed in Chapter 4.
Icon Purpose
Remote Console: Clicking this icon closes whatever is displayed on the
Main Screen, and brings back the Remote Console Preview.
Power Management: If the feature cable has been properly installed
(see Feature Cable Installation, page 9), and you have the proper
permission (see User Management, page 27), clicking this icon will bring
up an interface that allows you to Power On, Power Off, or Reset the
remote server.
Log: All the events that take place on the IP8000 are recorded in a log
file. If you have the proper permission (see User Management, page 27),
clicking this icon displays the contents of the log file. See Chapter 7, The
Log File, for further details.
Logout: Click this icon to log out and end your IP8000 session.
It is important to log out when you end your session. Otherwise, you must
wait until the timeout setting has expired before the IP8000 can be
accessed again. (See Timeout, page 29.)
ip8000.book Page 15 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
16
Remote Console Preview
The main portion of the screen shows a snapshot of the rem ote displ a y.
The active elements of the Remote Console Preview are described in the
following table:
Note: 1. If a user doesn’t have permission to open the Java Applet, the icon to
launch the applet does not appear.
2. If a user doesn ’t hav e perm issi on to open the Windows Client, the
icon to launch the client does not appear.
IP8000 operation using the Java applet is discussed in Chapter 6; IP8000
operation using the Windows client is discussed in Chapter 5.
Element Action
Refresh Clicking Refresh updates the snapshot of the remote
display.
Open Java Applet If you are on a platform other than Windows, clicking
Open Java Applet uses a Java applet to open the remote
server’s display on your desktop.
Open Windows Client If you are running Windows, clicking Open Windows
Client uses a Windows plugin to open the remote
server’s display on your desktop.
ip8000.book Page 16 Friday, May 9, 2008 10:39 AM
17
Chapter 4
Administration
Introduction
The administration utilities, represented by the icons located across the top of
the IP8000 web page, are used to configure the IP8000’s operating
environment.
This chapter discusses each of them in turn.
Note: 1. As you make your configuration changes in each dialog box, click
Apply to save them.
2. Some configuration changes only take effect after an IP8000 reset.
For those changes, a check is automatically pu t in the Reset on Exit
box (see Customization, page 29). To have the changes take effect,
log out and then log back in again.
3. If you do n't have Con figuration privileges (see User Management,
page 27), the Admini st ration configuration dialog s are not available.
ip8000.book Page 17 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
18
General
The General page is the first of the Administration pages, and pro vid es
information about the IP8000's status.
An explanation of each of the screen items is given in the table below:
Item Explanation
Device Name: To make it easier to manage installations that have more than one
IP8000, each one can be given a name. To assign a name for the
IP8000, key in one of your choosing here (16 characters max.).
MAC Address: The IP8000's MAC Address displays here.
Firmware Version: Indicates the IP8000's current firmware version level. New
versions of the IP8000's firmware can be downloaded from our
website as they become available (see Firmware, page 31). You
can reference this number to see if there are newer versions
available on the website.
Last IP from
DHCP Server If the IP8000 is on a network that uses DHCP assigned IP
addresses, this item is a convenient way of ascertaining what its
IP address is, in order to inform the Users which IP to use when
they log in.
Note: If the switch has a fixed IP address, this item doesn’t appear .
ip8000.book Page 18 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
19
Network
The Network dialog is used to specify the IP8000's network environment.
Access Ports
If a firewall is being used, the Administrator can specify the port numbers that
the firewall will allow. Users must specify the port number as part of th e IP
address If an invalid port number (or no port number) is specified, the IP8000
will not be found. An explanation of the fields is given in the table below:
Note: The access ports cannot have the same value. You must set a different
value for each one.
Field Explanation
Program: This is the port number used for keyboard, mouse, video, and
message data transfers. Valid entries are from 1024–65535. The
default is 9000.
Virtual Media: This is the port number used for data transfer using the IP8000’s
virtual media feature. V alid entries are from 1024–65535. The default
is 9003.
HTTP: The port number for a browser login. Valid entries are from 1–65535.
The default is 80.
HTTPs: The port number for a secure browser login. Valid entries are from
1–65535. The default is 443.
ip8000.book Page 19 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
20
IP Address
The IP8000 can either have its IP address assigned dynam icall y at bootup
(DHCP), or it can be given a fixed IP address.
For dynamic IP address assignment, select the Obtain an IP address
automatically, radio button.
Note: If the IP8000 is on a network that uses DHCP to assign network
addresses, and you need to ascertain its IP address, see IP Address
Determination, page 83, for information.
To specify a fixed IP address, select the Set IP address manually, radio
button and fill in the IP address.
DNS Server
The IP8000 can either have its DNS server address assigned automatically, or
a fixed address can be specified.
For automatic address assignment, select the Obtain DNS server address
automatically, radio button.
To specify a fixed address, select the Use the following DNS server
address, radio button and fill in the required informat ion.
Note: Specifying the Primary DNS Server address is required; the
Alternate DNS Server address is optional.
Finishing Up
After making any network changes, be sure Reset on exit on the Customization
page (see Customization, page 29) has been enabled (there is a check in the
checkbox), before logging out. Th is allow s network changes to take effect
without having to power the IP8000 off and on.
ip8000.book Page 20 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
21
Security
The Security page controls access to the IP8000.
Overview
IP and MAC Filters control access to the IP8000 based on the IP and/or
MAC addresses of the computers attempting to access the system. If any
filters have been configured, they appear in the IP Filter and/or MAC
Filter list boxes.
The Default web page name let s th e Admi nistrator specify a login string
(in addition to the IP address) that users must include when they access the
IP8000 with a browser. For example:
192.168.0.126/abcdefg
Users must include the forward slash and the string when they specify the
IP address in the browser’s URL bar. For security purposes, we
recommend that you change this string from time to time.
Note: If no string is specified here, anyone can access the IP8000 with a
Web browser using the IP address alone. This makes the installation
less secure.
ip8000.book Page 21 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
22
Filtering
To enable IP and/or MAC filtering, Click to put a check mark in the IP Filter
Enable and/or MAC Filter Enable checkbox. There are a maximum of 100
filters allowed for each.
If the include button is checked, all the addresses within the filter range are
allowed access; all other addresses are denied access.
If the exclude button is checked, all the addresses within the filter range
are denied access; all other addresses are allowed access.
IP Filtering
To add an IP filter:
1. Click Add. A dialog box similar to the one below appears:
2. Specify the filter address in the dialog box, then Click OK.
A second dialog box, similar to the one below, appears:
3. To filter a single IP address, key in the same address as the start IP. To
filter a continuous range of addresses, key in the end number of the range.
4. After filling in the address, cli ck OK.
5. Repeat these steps for any additional IP addresses you want to filter.
ip8000.book Page 22 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
23
To delete a filter, select it and Click Remove.
To modify a filter, select it and Click Edit. The Edit dialog box is similar to the
Add dialog box. When it comes up, simply delete the old address and replace
it with the new one.
MAC Filtering
To add a MAC filter:
1. Click Add. A dialog box similar to the one below appears:
2. Specify the MAC address in the dialog box, then Click OK.
3. Repeat these steps for any additional MAC addresses you want to filter.
To delete a filter, select it and Click Remove.
To modify a filter, select it and Click Edit. The Edit dialog box is similar to the
Add dialog box. When it comes up, simply delete the old address and replace
it with the new one.
ip8000.book Page 23 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
24
ANMS
The Advanced Network Management Settings dialog box allows you to set up
login authorization management from a external sources. It is divided into three
main panels, as described, below:
RADIUS Settings
To allow authorization for the IP8000 through a RADIUS server, do the
following:
1. Check Enable RADIUS.
2. Fill in the IP addresses and Service Ports for the Primary and Alternate
RADIUS servers.
3. In the Timeout field, set the time in seconds that the IP8000 waits for a
RADIUS server reply before it times out.
4. In the Retries field, set the number of allowed RADIUS retries.
5. In the Shared Secret field, key in the character string that you want to use
for authentication between the IP8000 and the RADIUS Server.
(Continues on next page.)
ip8000.book Page 24 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
25
(Continued from previous page.)
6. On the RADIUS server , set the access rights for each use r according to the
information in the table, below:
Note: 1. The characters are not case sensitive. Upper or lower case work
equally well.
2. Characters are comma delimited.
3. An invalid character in the configuration string will prohibit
access to the IP8000 for the user.
RADIUS Examples
RADIUS Server access rights examples are given in the table, below::
Character Meaning
C Grants the user administrator privileges, allowing the user to
configure the system.
W Allows the user to access the system via the Windows Client
program.
J Allows the user to access the system via Java.
PAllows the user to Power On/Off, Reset the computer that the IP8000
is connected to.
L Allows the user to access log information via the user's browser.
V Limits the user's access to only viewing the video display.
S Allows the user to use the virtual media function.
String Meaning
c,w,p User has administrator privileges; user can access the system via the
Windows Client; user can manage the attached Power over the NET
device.
w,j,l User can access the system via the Windows Client; user can access
the system via the Java Client; user can access log information via the
user’s browser.
ip8000.book Page 25 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
26
CC Management Settings
To allow authorization for the IP8000 through a CC (Control Center) server,
check Enable CC Management and fill in the CC Server’s IP address and the
port that it listens on in the appropriate fields.
Log Server Settings
Important transactions that occur on the IP8000, such as logins and internal
status messages, are kept in an automatically generated log file. See Chapter 8,
The Log Server, for details on setting up the log server.
Specify the MAC address of the computer that the Log Server runs on in
the MAC address field.
Specify the port used by the computer that the Log Server runs on to listen
for log details in the Port field. The valid po rt range is 1—6 5535. The
default port number is 9001.
ip8000.book Page 26 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
27
User Management
The User Management dialog box is used to create and manage user profiles.
Up to 64 user profiles can be established.
To add a user profile, fill in the information asked for in the User Info
panel and click Add. The user’s name appears in the User List pan el.
To delete a user profile, select it from the names displayed in the User List
panel, and click Remove. The user’s name is removed from the User List
panel.
To modify a user profile, first select it from the list in the upper panel; then
change the information that appears in the User Info dialog box.
Note: The user’s password is not displayed – the Password and Confirm
fields are blank. If you do not want to change the user’s password,
simply leave the two fields blank. If you do want to change the
user’s password, key the new password in the Password field, then
key it in again in the Confirm field.
When you have made all your changes, click Update.
The Reset button clears all the information shown in the User Info fields.
(Continues on next page.)
ip8000.book Page 27 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
28
(Continued from previous page.)
An explanation of th e profile items is given in the table bel ow:
Item Explanation
Username A minimum of 6 and a maximum of 16 characters is allowed.
Password A minimum of 6 and a maximum of 16characters is allowed.
Confirm Password To be sure there is no mistake in the password you are asked to
enter it again. The two entries must match.
Description Additional information about the user that you may wish to
include.
Permissions Click to place/remove a check mark next to an item to
grant/withhold access to that aspect of the IP8000’s operation.
Win Client: Checking Win client allows a user to access the
IP8000 via the Windows Client software.
View Only: Checking View Only allows a user to view the video
of the display of the computers attached to the ports of the KVM
switch connected to the IP8000, but they are not allowed to
perform any operations on the computers.
Power Management: Checking Power Management allows a
user to Power On / Power Off / Reset the computer that the
IP8000 is connected to.
Log: Checking Log allows a user to view the contents of the log
file.
Virtual Media: Checking Virtual Media allows a user to utilize
the IP8000’s virtual media capabilities (see Virtual Media,
page 40 for details).
Java Applet: Checking Java Applet allows a user to access the
IP8000 via the Java Applet software.
Configure: Checking Configure gives a user Administrator
privileges, and allows the user to set up and modify the IP8000's
operating environment.
ip8000.book Page 28 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
29
Customization
This configuration dialog allows the Administrator to set Timeout, Login
failure, and Working mode parameters.
An explanation of the Customization parameters is given in the table belo w:
(Continues on next page.)
Parameter Explanation
Timeout If the IP8000 doesn't receive any input from a computer
that is accessing it with the Windows Client or Java Applet
for the amount of time specified here, it ends the
connection.
Login
failures Allowed Sets the number of consecutive failed login attempts that
are permitted from a remote computer.
Timeout Sets the amount of time a remote computer must wait
before attempting to login again after it has exceeded the
number of allowed failures.
ip8000.book Page 29 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
30
(Continued from previous page.)
Item Explanation
Working
Mode Enable
ICMP If ICMP is enabled, the IP8000 can be pinged. If it is not
enabled, the device cannot be pinged.
Enable
device list If this item is enabled, the device will show up in the list of
local IP8000 units (see Starting Up, page 66). If it is not
enabled, it will not show up.
Enable
browser Placing a check in this box allows the user to access the
IP8000 from a browser. If this function is not enabled,
users will not be able to log into the unit via their browsers.
Enable
multiuser Enabling Multiuser operation permits up to 32 users to log
into the IP8000 at the same time through any combination
of: the browser-based Windows Client, the AP Windows
Client, the browser-based Java Applet, and the AP Java
Client.
Mouse
Sync Mode Automatic This is the default. Automatic causes an automatic
synching of the remote and local mouse pointers when a
connection to the remote display is made.
Note: This feature only supports USB mice on Windows
systems. For all other configurations, you must select
Manual.
Manual Selecting Manual means that no automatic mouse pointer
synching takes place. All synching must be done manually
with the Windows Client and Java Applet synching
procedures. (See Auto-Sync, page 39, and page 50 and
Adjust Mouse, page 37).
Also see Additional Mouse Synchronization Procedures,
page 89, for further help, if necessary.
Reset Some configuration changes only take effect after an
IP8000 reset. These include changes on the Network
page; a Log Server port change; enabling/disabling
browser access; and upgrading the firmware.
For those changes, a check is automatically put in the
Reset on Exit box.
To have the changes take ef fect, log out and then log back
in again. A wait of approximately 30 to 60 seconds is
necessary before logging in following the reset.
Note: If the IP8000’s performance degrades, reset it by
putting a check in the Reset on Exit box, and then log out /
log in.
ip8000.book Page 30 Friday, May 9, 2008 10:39 AM
Chapter 4. Administration
31
Firmware
As new versions of the IP8000 firm wa re become available, they can be
downloaded from our website. Check the website regularly to find the latest
information and packages.
To upgrade the firmware, do the follo wing:
1. Download the new firmware file to a computer that is not the one that your
IP8000 is installed on.
2. From that computer , open your browser; log in to the IP8000; and click the
Firmware
icon to bring up the
Firmware File
dialog box:
3. Click Browse; navigate to the directory that the new firmware file is in
and select the file.
4. Click Upload.
5. After the upload completes, the Reset on exit checkbox
(See Customization, page 29) will automatically be enabled. To have the
new firmware take effect, click Logout at the bottom left of the Main web
page to exit and reset the IP8000, then login again.
ip8000.book Page 31 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
32
This Page Intentionally Left Blank
ip8000.book Page 32 Friday, May 9, 2008 10:39 AM
33
Chapter 5
The Windows Client
Starting Up
After you log in (see Logging In, page 11), Click the Open Windows Client link
on the Remote Console Preview screen.
Note: 1. The first time you run the Windows client, you are prompted to install
a plugin (ip8000plugin.exe) that is required for its operation:
Click the link; in the dialog box th at comes up, click Run.
If the dialog box doesn’t have a Run option, click Save, then, with the
browser still open, run the file.
This brings up the plugin installation wizard. Click Next to start the
installation, then follow along with the wizard to com plete it .
Now, go back to the login screen and click Open Windows Client
again.
2. To unin stall the plugin, use the Windows Add or Remove Programs
function (Start → Control Panel → Add or Remove Programs).
(Continues on next page.)
ip8000.book Page 33 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
34
(Continued from previous page.)
A second or two after you click the Open Windows Client link, the remote
server’s display appears as a window on your desktop:
Navigation
You can work on the remote system via the screen display on your monitor just
as if it were your local system.
Note: 1. You can maximize the window, drag the borders to resize the
window; or use the scrollbars to move around the screen.
2. Due to net lag, there might be a slight delay before your keystrokes
show up. You may also have to wait a bit for the remote mouse to
catch up to your local mouse before you click.
3. Due to net lag, or insufficient computing power on the local machine,
some images, especially motion images, may display poorly.
ip8000.book Page 34 Friday, May 9, 2008 10:39 AM
Chapter 5. The Windows Client
35
The Windows Client Control Panel
The Windows Client control panel – located at the bottom right of the screen –
provides utilities to help you cont rol remote KVM operations.
The panel consists of an icon bar with a text bar below it. The text bars displays
the remote server’s video resolution.
Note: You can move the control panel to any convenient location on the screen
by moving the mouse pointer over one of its borders and dragging.
(Continues on next page.)
ip8000.book Page 35 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
36
(Continued from previous page.)
The functions that the icons perform is described in th e table belo w:
The Windows Client Control Panel icons and their functions are described in
the sections that follow.
Icon Function
Click to bring up the Hotkey setup dialog box (see Hotkey Setup,
page 37 for details).
Click to bring up the Video settings dialog box.
Click to bring up the Virtual media dialog box.
Click to bring up the Message board.
Click to send a Ctrl+Alt+Del signal to the remote system.
Click to exit the remote view.
These icons show the Num Lock, Caps Lock, and Scroll Lock status
of the remote computer.
When the lock state is On, the LED is bright green and the lock hasp
is closed.; When the lock state is Off, the LED is dull green and the
lock hasp is open. Click on the icon to toggle the status.
Note: When you first connect, the LED display may not be accurate.
To be sure, click on the LEDs to set them.
ip8000.book Page 36 Friday, May 9, 2008 10:39 AM
Chapter 5. The Windows Client
37
Hotkey Setup
Various actions related to manipulating the rem ote server can be
accomplished with hotkeys. The Hotkey Setup utility is accessed by
clicking the Keyboard icon on the Control Panel. The actions performed by the
Hotkeys are listed in the left panel; the curren tly de fined keys that invoke the
actions are shown in the panel to the right.
Action Explanation
Toggle screen mode Toggles the screen display between full screen and
windowed modes.
Adjust Video Brings up the video setting dialog box.
Toggle OSD Toggles the control panel Off and On.
Toggle pointer display If you find the display of the two mouse pointers (local and
remote) to be confusing or annoying, you can use this
function to hide the non-functioning poin t er. Since this
function is a toggle - use the hotkeys again to bring the
pointer display back to its original configuration.
Adjust Mouse Synchronizes the movement of the local and remote mice.
Substitute Alt Key Although all other keyboard input is captured and sent to the
IP8000, [Alt + Tab] and [Ctrl + Alt + Del] work on your local
computer. In order to implement their effects on the remote
system, a function key is substituted for the Alt key. If you
substitute the F12 key, for example, you would use [F12 +
Tab] and [Ctrl + F12 + Del].
Exit remote view Ends the remote connection to the IP8000 and returns to
local operation.
ip8000.book Page 37 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
38
Configuring the Hotkeys
If you find the default Hotkey com bi nations inconvenient, you can configure
them by following these steps:
1. Highlight the Action , then Click Start
2. Key in the new combination. The key names appear in the Key field as you
press them.
3. Click Set
4. Click Close.
ip8000.book Page 38 Friday, May 9, 2008 10:39 AM
Chapter 5. The Windows Client
39
Video Settings
The Video settings dialog box allows you to adjust the placement and
picture quality of the remote screen (as displayed on your monitor).
The meanings of the adjustme nt options are given in the table below:
Option Usage
Screen Position Adjust the horizontal and vertical position of the remote
computer window by Clicking the Arrow buttons.
Auto-Sync Click Auto-Sync to have the function detect the vertical and
horizontal offset values of the remote screen and automatically
synchronize it with the local screen.
If the local and remote mouse pointers are out of sync, in most
cases, performing this function will bring them back into sync.
Note: This function works best with a bright screen.
If you are not satisfied with the results, use the Screen Position
arrows to position the remote display manually.
Video Quality Drag the slider bar to adjust the overall Video Quality. The higher
the value, the clearer the picture and the more video data goes
through the network. Depending on the network bandwidth, a
high value may slow down response time.
ip8000.book Page 39 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
40
Virtual Media
The IP8000’s virtual media feature allows a USB 2.0 device (Floppy
drive, CDROM, Flash Drive, etc.), or an image file, on a user’s
system, to appear, and act, as if it were installed on the remote server.
To implement this redirection feat ure, do the following:
1. Bring up the Virtual media dialog box:
2. Select the media source.
a) If you select Drive, drop down the drive list to select the appropriate
drive:
b) If you select File, click the button with the three dots to browse to your
image file.
ip8000.book Page 40 Friday, May 9, 2008 10:39 AM
Chapter 5. The Windows Client
41
3. After you have made your media source selection, click Start. The device
(or image file) that you have selected is then redirected to the remote
server, where it shows up as a drive on the remote server’s file system.
Note: You can dismiss the Virtual media dialog bo x at th is po int – the
redirection will stay in effect.
You can treat the folder as if it were really on the remote server – drag and
drop files to/from it; open files on the remote system for editing and save
them to the redirected drive, etc.
Files that you save to the redirected drive, wi ll actually be saved to the
USB device on your local system. Files that you drag from the redi rect ed
drive will actually come from the USB device on your local system.
4. To end the redirection, bring up the Virtu al medi a dialo g box and click
Stop.
ip8000.book Page 41 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
42
Message Board
The IP8000 supports multiple user logins, which can possibly give rise
to access conflicts. To alleviate this problem, a message board, similar
to an internet chat program, allows users to communicate with each other:
(Continues on next page.)
ip8000.book Page 42 Friday, May 9, 2008 10:39 AM
Chapter 5. The Windows Client
43
(Continued from previous page.)
The Button Bar
The buttons on the Button Bar are toggles. Their actions are described in the
table below:
Compose Panel
Key in the messages that you want to post to the board in thi s pane l. Click
Send, or press [Enter] to post the message to the board.
Message Display Panel
Messages that users post to the board - as well as system messages - display in
this panel. If you disable Chat, however, messages that get posted to the board
won't appear.
Button Action
Enable/Disable Chat. When disabled, messages posted to the
board are not displayed. The icon displays next to the user's name in
the User List panel when he has disabled Chat.
Occupy/Release Keyboard/Video/Mouse. When you Occupy the
KVM, other users cannot see the video, and cannot input keyboard or
mouse data. The icon displays next to the user's name in the User
List panel when he has occupied the KVM.
Occupy/Release Keyboard/Mouse. When you Occupy the KM,
other users can see the video, but cannot input keyboard or mouse
data. The icon displays next to the user's name in the User List panel
when he has occupied the KM.
Show/Hide User List. When you Hide the User List, the User List
panel closes.
ip8000.book Page 43 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
44
User List Panel
The names of all the logged in users appear in the User List panel. Select
the names of the users that you wish to send the message to before sending
your message.
If a user has disabled Chat, its icon displays before the user's name to
indicate so.
If a user has occupied the KVM or the KM, its icon displays before the
user's name to indicate so.
ip8000.book Page 44 Friday, May 9, 2008 10:39 AM
45
Chapter 6
The Java Applet
Introduction
The Java Applet makes the IP8000 accessible to all platforms that have JRE 6
Update 3 or higher installed. Java is available for free download from Sun's
Java web site (http://www.java.com or http://java.sun.com). To access the
IP8000 with the Java Applet :
After you log in (see Logging In, page 11), Click the Open Java Applet link on
the Remote Console Preview screen.
Note: If a Security Warning dialog box appears, click Run, to accept it.
After a second or two, the remote server’s display appears as a window on your
desktop:
ip8000.book Page 45 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
46
Navigation
You can work on the remote system via the screen display on your monitor just
as if it were your local system.
You can maximize the window, drag the borders to resize the window; or
use the scrollbars to move around the screen.
You can switch between your local and remote pro grams with [Alt + Tab].
Note: 1. Due to net lag, there might be a slight delay before your keystrokes
show up. You may also have to wait a bit for the remote mouse to
catch up to your local mouse before you click.
2. Due to net lag, or insufficient computing power on the local machine,
some images, especially motion images, may display poorly.
The Java Applet Control Panel
The Java Applet control panel – located at the bottom right of the screen –
provides utilities to help you control remote KVM operations.
The panel consists of an icon bar with a text bar below it. The text bars displays
the remote server’s video resolution.
Note: You can move the control panel to any convenient location on the screen
by moving the mouse pointer over one of its borders and dragging.
(Continues on next page.)
ip8000.book Page 46 Friday, May 9, 2008 10:39 AM
Chapter 6. The Java Applet
47
(Continued from previous page.)
The functions that the icons perfo rm is described in the table below:
The Java Applet Control Panel icons and their functi ons are descri bed in the
sections that follow.
Icon Function
Click to bring up the Hotkey setup dialog box (see Hotkey Setup,
page 48 for details).
Click to bring up the Video settings dialog box.
Click to bring up the Message board (see page 51).
Click to send a Ctrl+Alt+Del signal to the remote system.
Click to exit the remote view.
The Lock Key LEDs show the Num Lock, Caps Lock, and Scroll Lock
status of the remote computer.
When the lock state is Off, the LED is dull green and the lock hasp
is open.
When the lock state is On, the LED turns bright green and the lock
hasp is closed.
Click on the icon to toggle the status.
Note: When you first connect, the LED display may not be accurate.
To be sure, click on the LEDs to set them.
ip8000.book Page 47 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
48
Hotkey Setup
Various actions related to manipulating the remote server can be
accomplished with hotkeys. The Hotkey Setup utility is accessed by
clicking the Keyboard icon on the Control Panel. The actions performed by the
Hotkeys are listed in the left panel; the currently defined keys that invoke the
actions are shown in the panel to the right .
Action Explanation
Toggle screen mode Toggles the screen display between full screen and
windowed modes.
Adjust Video Brings up the video setting dialog box.
Toggle OSD Toggles the control panel Off and On.
Toggle pointer display If you find the display of the two mouse pointers (local and
remote) to be confusing or annoying, you can use this
function to hide the non-functioning pointer. Since this
function is a toggle - use the hotkeys again to bring the
pointer display back to its original configuration.
Adjust Mouse Synchronizes the movement of the local and remote mice.
Substitute Alt Key Although all other keyboard input is captured and sent to the
IP8000, [Alt + Tab] and [Ctrl + Alt + Del] work on your local
computer. In order to implement their effects on the remote
system, a function key is substituted for the Alt key. If you
substitute the F12 key, for example, you would use [F12 +
Tab] and [Ctrl + F12 + Del].
Exit remote view Ends the remote connection to the IP8000 and returns to
local operation.
ip8000.book Page 48 Friday, May 9, 2008 10:39 AM
Chapter 6. The Java Applet
49
Configuring the Hotkeys
If you find the default Hotkey combinations inconvenient, you can reconfigure
them by following these steps:
1. Highlight the Action, then click Start.
2. Key in the new combination. The key names appear in the Key field as you
press them.
3. Click Set.
4. Click Close.
ip8000.book Page 49 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
50
Video Settings
The Video settings dialog box allows you to adjust the placement and
picture quality of the remote screen (as displayed on your monitor).
The meanings of the adjustment opt ions are given in the table below:
Option Usage
Screen position A djust the horizontal and vertical position of the remote
computer window by Clicking the Arrow buttons.
AutoSync Click Auto-Sync to have the function detect the vertical and
horizontal offset values of the remote screen and automatically
synchronize it with the local screen.
If the local and remote mouse pointers are out of sync, in most
cases, performing this function will bring them back into sync.
Note: This function works best with a bright screen.
If you are not satisfied with the results, use the Screen Position
arrows to position the remote display manually.
Video quality Drag the slider bar to adjust the overall Video Quality (right is
higher; left is lower). The higher the value, the clearer the picture
and the more video data goes through the network. Depending
on the network bandwidth, a high value may slow down
response time.
ip8000.book Page 50 Friday, May 9, 2008 10:39 AM
Chapter 6. The Java Applet
51
Message Board
The IP8000 supports multiple user logins, which can possibly give rise
to access conflicts. To alleviate this problem, a message board feature,
similar to an internet chat program, allows users to communicate with each
other:
The buttons on the Button Bar are toggles. Their actions are described in the
table below:
Enable/Disable Chat. When disabled, messages posted to the
board are not displayed. The icon displays next to the user's name
in the User List panel when he has disabled Chat.
Occupy/Release Keyboard/Video/Mouse. When you Occupy the
KVM, other users cannot see the video, and cannot input keyboard
or mouse data. The icon displays next to the user's name in the
User List panel when he has occupied the KVM.
Occupy/Release Keyboard/Mouse. When you Occupy the KM,
other users can see the video, but cannot input keyboard or mouse
data. The icon displays next to the user's name in the User List
panel when he has occupied the KM.
ip8000.book Page 51 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
52
The names of all the logged in users appear in the User List panel.
Select the users that you want to post to before sending your message.
Users that aren’t selected won’t see the message.
To Hide/Unhide the User List panel, click on the arrows in the panel
separator.
If a user has disabled Chat, the Disabled Cha t icon displays before th e
user's name to indicate so.
If a user has occupied the KVM or the KM, the corresponding icon
displays before the user's name to indi cate so.
Key in the messages that you want to post to the board in the Compose
panel. Click Send, to post the message to the board.
Messages that users post to the board – as well as system messages –
display in the Message Display panel. If you disable Chat, however,
messages that get post ed to the board do not appear.
ip8000.book Page 52 Friday, May 9, 2008 10:39 AM
Chapter 6. The Java Applet
53
Ctrl+Alt+Del
Clicking this button sends a Ctrl+Alt+Del signal to the remote system.
Exit
Click this button to exit the Java Applet and return to local operation.
Lock LEDs
The Lock Key LEDs show the Num Lock, Caps Lock, and Scroll
Lock status of the remote computer.
When the lock state is Off, the LED is dull green and the lock hasp is open.
When the lock state is On, the LED turns bright green and the lock hasp is
closed.
Click on the icon to toggle the status.
Note: When you first connect, the LED display may not be accurate. To be
sure, click on the LEDs to set them.
ip8000.book Page 53 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
54
This Page Intentionally Left Blank
ip8000.book Page 54 Friday, May 9, 2008 10:39 AM
55
Chapter 7
The Log File
The Log File Screen
The IP8000 logs all the events that take place on it. To view the contents of the
log file in th e browser, cl ick the Log icon at the left of the web page. A screen
similar to the one below appears:
A maximum of 512 events are kept in the log file. As new events are recorded,
they are placed at the bottom of the list. When a new event is recorded after
there are 512 events in the log file, the earliest event in the list is discarded. To
clear the log file, click on the Clear Log icon at the lower right of the page.
Note: If the server that the IP8000 is installed in is shut down , and the
IP8000’s power adapter isn’t plugged in, the contents of the browser-
based log file are lost. If the Log Server has been properly installed and
configured, however, the log data can be retrieved from there. See
Chapter 8, The Log Server, for details
ip8000.book Page 55 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
56
This Page Intentionally Left Blank
ip8000.book Page 56 Friday, May 9, 2008 10:39 AM
57
Chapter 8
The Log Server
Introduction
The Windows-based Log Server is an administrative utility that records all the
events that take place on selected IP8000 units and writes them to a searchable
database. The installer for the Log Server program – LogSetup.exe – can be
found on the IP8000 software CD. This chapter describes how to install and
configure the Log Server.
Installation
Installation
To install the Log Server program, do the following:
1. Copy LogSetup.exe from the software CD to a convenient location on your
hard disk.
2. Run the program and follow along with the installation dialog boxes.
When the installation completes, an icon – LogServer – is placed on your
desktop and a program entry is made in the Window s Start menu:
(Start → All Programs → LogServer → LogServer).
(Continues on next page.)
ip8000.book Page 57 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
58
(Continued from previous page.)
Starting Up
To bring up the Log Server, either double click the program icon, or key in the
full path to the program on the command line. The first time you run it, a screen
similar to the one below appears:
Note: 1. The MAC address of the Log Server computer must be specified in
the ANMS settings – see page 2 4 for details.
2. The Log Server requires the Microsoft Jet OLEDB 4.0 driver in order
to access the database.
The screen is divided into three components:
A Menu Bar at the top
A panel that will contain a list of IP8000 uni ts in the mi ddle (see The Log
Server Main Screen, page 63, for details).
A panel that will contain an Events List at the bottom
Each of the components is explained in the sections that follow.
ip8000.book Page 58 Friday, May 9, 2008 10:39 AM
Chapter 8. The Log Server
59
The Menu Bar
The Menu bar consists of four items:
Configure
Events
Options
Help
These are discussed in the sections that follow.
Note: If the Menu Bar appears to be disabled, click in the IP8000 List window
to enable it.
Configure
The Configure menu contains three items: Add, Edit, and Delete. They are used
to add new IP8000 units to the IP8000 List, edit the information for units
already on the list, or delete IP8000 units from the list.
To add a IP8000 to the IP8000 List, cl ick Add.
To edit or delete a listed IP8000, first select the one you want in the IP8000
List window, then open this menu and click Edit or Delete.
When you choose Add or Edit, a dialog box, similar to the one below appears:
ip8000.book Page 59 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
60
A descriptio n of the fields is giv en in the table, below:
Fill in or modify the fields, then click OK to finish.
Events
The Events Menu has two items: Search and Maintenance.
Search
Search allows you to search for events containing specific words or strings.
When you access this function, a screen similar to the one below appears:
Field Explanation
Address This can either be the IP address of the IP8000 or its DNS name (if the
network administrator has assigned it a DNS name). Key in the value
specified for the IP8000 in the ANMS settings (see ANMS, page 24).
Port Key in the port number that was specified for the IP8000 in the ANMS
settings (see ANMS, page 24).
Description This field is provided so that you can put in a descriptive reference for
the unit to help identify it.
Limit This specifies the number of days that an event should be kept in the
Log Server's database before it expires and it is cleared out.
ip8000.book Page 60 Friday, May 9, 2008 10:39 AM
Chapter 8. The Log Server
61
A description of the items is given in the tabl e be low:
Maintenance
This function allows the administrator to perform manual maintenance of the
database, such as erasing specified records before the expiration time that was
set with the Limit setting of the Edit function (see page 60).
Item Explanation
New search This is one of three radio buttons that define the scope of the
search. If it is selected, the search is performed on all the
events in the database for the selected IP8000.
Search last results This is a secondary search performed on the events that
resulted from the last search.
Search excluding last
results This is a secondary search performed on all the events in the
database for the selected IP8000 excluding the events that
resulted from the last search.
Server List IP8000 units are listed according to their IP address. Select
the unit that you want to pe rform the search on from this list.
You can select more than one unit for the search. If no units
are selected, the search is performed on all of them.
Priority List Sets the level for how detailed the search results display
should be. 1 is the most general; 3 is the most specific.
Start Date Select the date that you want the search to start from. The
format follows the MM/DD/YYYY convention, as follows:
11/04/2005
Start Time Select the time that you want the search to start from.
End Date Select the date that you want the search to end at.
End Time Select the time that you want the search to end at.
Pattern Key in the pattern that you are searching for here. The
multiple character wildcard (%) is supported. E.g., h%ds
would match hands and hoods.
Results Lists the events that contained matches for the search.
Search Click this button to start the search.
Print Click this button to print the search results.
Exit Click this button to exit the Search dialog box.
ip8000.book Page 61 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
62
Options
Network Retry allows you to set the number of seconds that the Log Server
should wait before attempting to connect if the previous attempt to connect
failed. When you click this item, a dialog box, similar to the one below appears:
Key in the number of seconds, then click OK to finish.
Help
From the Help Menu, click Contents to access the online Windows Help file.
The help file contains instructions about how to setup, operation and
troubleshoot the Log Server.
ip8000.book Page 62 Friday, May 9, 2008 10:39 AM
Chapter 8. The Log Server
63
The Log Server Main Screen
Overview
The Log Server Main Screen is divided into two main panels.
The upper (List) panel lists the IP8000 units that have been selected for the
Log Server to track (see Configure, page 59).
The lower (Event) panel displays the log events for the currently selected
IP8000 (the highlighted one - if there are more than one). To select a
IP8000 unit in the list, sim ply click on it.
ip8000.book Page 63 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
64
The List Panel
The List panel contains six fields:
The Tick Panel
The lower panel displays tick informati on for the currently selected IP8000.
Note that if the installation contains more than one switch, even though a
switch isn’t currently selected, if its Recording checkbox is checked, the Log
Server records its tick information and keeps it in its database.
Field Explanation
Recording Determines whether the Log Server records log events for
this IP8000 or not. If the Recording check box is checked, the
field displays Recording, and log events are recorded. If the
Recording check box is not checked, the field displays
Paused, and log events are not recorded.
Note: Even though a IP8000 is not the currently selected
one, if its Recording check box is checked, the Log Server will
still record its log events.
Address This is the IP Address or DNS name that was given to the
IP8000 when it was added to the Log Server (see Configure,
page 59).
Port This is the port number that was assigned to the IP8000 when
it was added to the Log Server (see Configure, page 59).
Connection If the Log Server is connected to the IP8000, this field
displays Connected.
If it is not connected, this field displays Waiting. This means
that the Log Server's MAC address and/or port number has
not been set properly . It needs to be set in the ANMS settings
(see page 24) and specified in the Configure dialog box (see
Configure, page 59).
Days This field displays the number of days that the IP8000's log
events are to be kept in the Log Server's database before
expiration (see Configure, page 59).
Description This field displays the descriptive information given for the
IP8000 when it was added to the Log Server (see Configure,
page 59).
ip8000.book Page 64 Friday, May 9, 2008 10:39 AM
65
Chapter 9
AP Operation
Introduction
In addition to the browser based client utilities, the IP8000 also provides
stand-alone Windows and Java applications that can be used without a browser.
Both applications can be found on the IP8000 softw a re CD. The inst aller for
the Windows Client program is called ip8000winclient.exe; the Java Client
program is called iClientJ.jar.
The AP Windows Client
Installation
To install the stand-alone Windows Client program, do the following:
1. Copy ip8000winclient.exe from the software CD to a convenient location
on your hard disk.
2. Run the program and follow along with the installation dialog boxes.
When the installation completes, an icon – IP8000 WinClient – is placed on
your desktop and a program entry is made in the Wi ndows Start menu:
(Start → All Programs → IP8000 → IP8000 WinClient).
(Continues on next page.)
ip8000.book Page 65 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
66
(Continued from previous page.)
Starting Up
To connect to the IP8000, either click its icon on the desktop or click its entry
on the Start menu.
If this is the first time that you are running the utility, a dialog box appears
requesting you to input your seri al number.
The serial number can be found on the IP800 0's CD case. Key in the serial
number - 5 characters per box - then click OK to bring up the IP8000
Connection Screen.
Note: 1. Letters in the serial number must be entered in capitals.
2. This dialog box only appears the first time you run the program. In the
future, you go directly to the Windows Client Connection screen.
ip8000.book Page 66 Friday, May 9, 2008 10:39 AM
Chapter 9. AP Operation
67
The Windows Client Connection Screen
A description of the Connecti on Screen is given in the following table:
Item Description
Server List Each time the WinClient program is run, it searches the user's
local LAN segment for IP8000 units, and list s whichever ones
it finds in this box. If you want to connect to one of these
units, select it, then click Login. When you have finished with
your session, Click Logout to end the connection.
Server This area is used when you want to connect to a IP8000 at a
remote location. You can drop down the IP list box and select
an address from the list. If the address you want isn't listed,
you can key in the IP address you want. Then, key in the Port
number in the Port field. If you don't know the Port number,
contact the Administrator.
When the IP address and Port number for the unit you wish to
connect to have been specified, click Login to start the
connection. When you have finished with your session, Click
Logout to end the connection.
Login Starts the connection to the IP8000.
Logout
These buttons become active once you log into the IP8000.
See page 69 for details.
Remote View
Change Password
Admin Utility
ip8000.book Page 67 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
68
Logging In
Once the IP8000 connects to the unit you specified, a login window appears:
Provide a valid Username and Password, then Click OK to continue.
Note: The default Username is administrator; the default Password is
password. For security, we stron gly recommend that you change these
to something unique (see User Management, page 74, for details).
(Continues on next page.)
ip8000.book Page 68 Friday, May 9, 2008 10:39 AM
Chapter 9. AP Operation
69
(Continued from previous page.)
After you have successfully logged in, the Connection screen reappears:
At this time there are four active buttons, as describe d in the tab le, below:
Button Action
Logout Breaks the connection to the IP8000.
Remote View In some cases, administrator’s do not wish to have users connect
to the IP8000 with a browser . Remote View solves this problem. It
opens a window on the user’s desktop containing the remote
server’s display that is the same as the one that appears with the
browser-based Windows client. Refer to Chapter 5, The Windows
Client, for operation details.
Change Password Allows users to change their passwords without administrator
intervention.
Admin Utility The Administrator Utility provides administrators with a non-
browser based method for configuring and controlling IP8000
operations. The Administrator Utility is discussed in the sections
that follow.
ip8000.book Page 69 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
70
The Administrator Utility
The Administrator Utility appears as a notebook with six tabs . Each tab
represents a different administrative function. A description of the fu nctions
and how to configure their settings is provided in th e sections that follow.
General
The Settings notebook opens with the General page displayed:
The General page provides information about the IP8000's status, as explained
in the table, below:
Item Description
Device Name: To make it easier to manage installations that have more
than one IP8000, each one can be given a name. To
assign a name for the IP8000, erase the current name
and key in one of your choosing (16 characters max.).
MAC Address The IP8000's MAC Address displays here.
Main Firmware Version: Indicates the mainboard's current firmware version level.
New versions of the IP8000's firmware and
authentication software can be downloaded from our web
site as they become available (see Upgrading the
Firmware, page 76, for details).
ip8000.book Page 70 Friday, May 9, 2008 10:39 AM
Chapter 9. AP Operation
71
Network
This page is used to specify the IP8000's network environment.
The settings on this page are essentially the same as that of the browser-based
version. See Network, page 19, for details.
Note: Be sure to enable Reset on exit on the Customization page (see page 75)
before exiting the Administrator Utility . This allows network changes to
take effect without having to power the IP8000 off and on.
ip8000.book Page 71 Friday, May 9, 2008 10:39 AM
Chapter 9. AP Operation
73
ANMS
The Advanced Network Management Settings dialog box allows you to set up
login authorization manag e ment from a external sources.
The settings on this page are essentially the same as that of the browser-based
version. See ANMS, page 24, for details.
ip8000.book Page 73 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
74
User Management
This page is used to set up and manage user profiles. It defines the access rights
of each user. Up to 64 user profiles can be established
The settings on this page are essentially the same as that of the browser-based
version. See U ser Management, page 27, for detai ls.
ip8000.book Page 74 Friday, May 9, 2008 10:39 AM
Chapter 9. AP Operation
75
Customization
This page allows the Administrator to upgrade the firmware and to set to set
various working parameters.
Except for the Firmware Upgrade section, the setting s on this page are
essentially the same as that of the browser-based version. See Customization,
page 29, for details on setting Timeout, Login failure, Working mode, and
Mouse Sync Mode parameters.
The Firmware Upgrade section is used when upgrading the IP8000’s firmware.
Upgrading the firmware is discussed in the next section.
ip8000.book Page 75 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
76
Upgrading the Firmware
New versions of the Mainboard firmware files can be downloaded from our
website as they become available. After downloading the new firmware file, to
upgrade the firmware, do the following:
1. On the Customization page of the Administration Utility’s configuration
notebook (see page 75) click the Browse button.
2. In the File Open dialog box that appears, navigate to the directory that the
downloaded firmware upg rade file is in; select the file; then click Open.
3. When you return to the Customization page, the file appears in the
Mainboard F/W field. Click OK to perform the upgrade.
ip8000.book Page 76 Friday, May 9, 2008 10:39 AM
Chapter 9. AP Operation
77
The AP Java Client
The Java Client is provided to make the IP8000 accessible to all platforms.
Systems that have JRE 6 Update 3 or higher installed can connect. If you don't
already have Java, it is available for free download from Sun's Java web site
(http://www.java.com or http://java.sun.com).
Starting Up
To connect to the IP8000 with the stand-alone Java Client program, copy
iClientJ.jar to a convenient location on yo ur hard disk; then dou ble-click its
icon – or key in the full path to the program on the command line – to bring up
the Java Client Connection screen.
Note: 1. Letters in the serial nu mber must be entered in capitals.
2. If this is the first time that you are running the program a dialog box
appears requesting you to input your serial number.
The serial number can be found on the IP8000's CD case. Key in the
serial number - 5 characters per box - then click OK to bring up the
IP8000 Connection Screen.
After performing this operati on the fi rst time you run the program,
this dialog box doesn’t appear again – you go directly to the Java
Client Connection screen.
ip8000.book Page 77 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
78
The Java Client Connection Screen
To connect to the IP8000
1. Key in its IP address in the Server field.
2. If the port number shown isn’t correct, key in the correct number.
3. Click Connect.
Logging In
Once the IP8000 connects to the unit you specified, a login window appears:
Provide a valid Username and Password, then Click OK.
Note: The default Username is administrator; the default Password is
password. For security, we stron gly recommend that you change these
to something unique (see User Management, page 74, for details).
After you have successfully logged in, a window opens on your deskto p
containing the remote server’s display. This is the same window that appears
when you run the browser-based Java applet. Refer to Chapter 6, The Java
Applet, for operation details.
ip8000.book Page 78 Friday, May 9, 2008 10:39 AM
79
Appendix
Safety Instructions
General
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage wi ll resul t.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be bl ocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been
provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device shoul d be oper ated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
ip8000.book Page 79 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
80
When connecting or disconnect ing po wer to hot-pluggable power
supplies, observe the following guidelines:
Install the power supply before connecting the power cable to the
power supply.
Unplug the power cable before removing the po wer supply.
If the system has multiple sources of power , disconnect power from the
system by unplugging all power cables from the power supplies.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yoursel f. Refer all servicin g to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
ip8000.book Page 80 Friday, May 9, 2008 10:39 AM
Appendix
81
Technical Support
International
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration , including operating system, revision leve l,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten.com
Online
Support Technical Support http://support.aten.com
Troubleshooting
Documentation
Software Updates
http://www.aten.com
Telephone Support 886-2-8692-6959
Email Support ATEN TECH support@aten-usa.com
ATEN NJ sales@aten.com
Online
Support Technical Support ATEN TECH http://www.aten-usa.com/support
ATEN NJ http://support.aten.com
Troubleshooting
Documentation
Software Updates
ATEN TECH http://www.aten-usa.com
ATEN NJ http://www.aten.com
Telephone Support ATEN TECH 1-888-999-ATEN
ATEN NJ 1-732-356-1703
ip8000.book Page 81 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
82
Specifications
Function Specification
Connectors Console Ports Video 1 x HDB-15 Female
KVM Link 1 x SPHD-15 Female
LAN 1 x RJ-45 Receptacle
Power 1 x DC Jack 5V
LEDs Link 1 (Green)
10/100 Mbps 1 (Orange/Green)
Emulation Keyboard/Mouse USB; PS/2
Video 1600 x 1200 @ 60 Hz; DDC2B
Power Consumption DC 5 V; 5.5 W
Environment Operating Temp. 0–50o C
Storage Temp. -20–60o C
Humidity 0–80% RH
Physical
Properties Weight 0.10 kg
Dimensions (L x W x H) 15.35 x 12.00 x 2.15 cm
ip8000.book Page 82 Friday, May 9, 2008 10:39 AM
Appendix
83
IP Address Determination
If you are an administrator logging in for the first time, you need to access the
IP8000 in order to give it an IP address that users can connect to. There are two
methods to choose from: 1) Resetting Your Computer Address ; and 2) r unning
the Windows Client program.
The first method is useful for determining the IP value of devices with fixed
addresses. The Windows Client method is good for determining the IP value of
devices with either fixed or DH CP derived IP addresses. With either method
your computer must be on the same network segment as the IP8000.
Note: The Windows Client method is especially useful if the device’s DHCP
assigned address changes.
After you have connected and logged in to the IP8000, you can give it a fixed
network address in the Network Settings dialog box (see page 19).
Resetting Your Computer Address
For non-Windows computers, a browser based method for setting the IP8000’s
IP address is available. It is based on the fact that when the IP8000 starts, if it
doesn't find a DHCP environment after 30 seconds, it automatically sets its IP
address to 192.168.0.60. To set the IP8000’s address with this method, do the
following:
1. Set your computer's IP address to 192.168.0 .XXX
Where XXX represents any number or numbers except 60.
2. Specify the switch's default IP address (192.168.0.60) in the URL entry
box of your browser.
3. After you connect and log in, click the Network icon (see page 19) to
assign a fixed IP address for the IP8000 that is suitab le for the network
segment that it resides on.
4. After you log out, be sure to reset your computer's IP address to its original
value.
ip8000.book Page 83 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
84
The Windows Client
For computers running Windows, the IP80 00's IP address can be determined
with the Windows stand-alone application program.
When you run the Windows stand-alone application (see page 65), it searches
the network segment for IP8000 devices, and displays what it finds in a dialog
box similar to the one below:
You can now use this network address if it is suitable to do so. You can change
it to a more suitable one if you wish, by clicking Login, logging in, clicki ng
Admin Utility, and clicking the Network tab. See Network, page 71, for
details.
ip8000.book Page 84 Friday, May 9, 2008 10:39 AM
Appendix
85
Administrator Login Failure
If you are unable to perform an Administrator login to the IP8000 (because the
Username and Password information has become corrupt ed, or you have
forgotten it, for example), th ere is a procedure you can use to clear the login
information.
Note: Performing this procedure also returns all settings to their defaults.
To clear the login information (and return all settings to their defaults), do the
following:
1. Power off the IP8000 by unplugging its power adapter cable.
2. Power off the server that the IP8000 is installed in and remove its housing.
3. Short the jumper on the IP8000 labeled J2 Default Password.
4. Power on the IP8000 by plugging its power adapter cable back in. Wait a
few seconds, then unplug it again.
5. Remove the jumper cap from J2.
6. Close the housing and start the server back up.
7. Plug the IP8000’s by power adapter cable back in.
After you complete these steps, you can use the default Username and
Password (see page 13) to lo g into the IP8000.
ip8000.book Page 85 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
86
Troubleshooting
Overview
Operation problems can be due to a variety of causes. The first step in solving
them is to make sure that all cables are securely attached and seated completely
in their sockets.
In addition, updating the product’s fi rmware may solve problem s that have
been discovered and resolved since the prior version was released. If your
product is not running the latest firmware version, we strongly recommend that
you upgrade. See Upgrading the Firmware, page 76, for upgrade details.
The Windows Client
Problem Resolution
Remote mouse pointer is
out of step. Use the AutoSync feature (see Video Settings, page 39), to
synch the local and remote monitors.
If the method shown above fail to resolve the problem, use
the Toggle Mouse Display function (see page 37).
If the procedures above fail to resolve the problem, perform
the operations described under Additional Mouse
Synchronization Procedures, page 89, on both the local
and remote computers.
Part of remote window is
off my monitor. Use the AutoSync feature (see Video Settings, page 39), to
sync the local and remote monitors.
When I log in, the
browser generates a CA
Root certificate is not
trusted, or a Certificate
Error response.
The certificate’s name is not found on Microsoft’s list of
Trusted Authorities. The certificate can be trusted.
See Trusted Certificates, page 91, for details.
ip8000.book Page 86 Friday, May 9, 2008 10:39 AM
Appendix
87
The Java Client
The Log Server
Symptom Action
Java Client won't connect
to the IP8000 1. JRE 6 Update 3 or higher must be installed on your
computer.
2. Close the Java Client, reopen it, and try again.
Java Client performance
deteriorates. Exit the program and start again.
National language
characters don't appear. When entering national language characters, if your local
keyboard is set to a non-English national language
layout, you must set the remote computer's keyboard
layout to English.
When I log in, the browser
generates a CA Root
certificate is not trusted, or
a Certificate Error
response.
The certificate’s name is not found on Microsoft’s list of
Trusted Authorities. The certificate can be trusted.
See Trusted Certificates, page 91, for details.
There is no Virtual Media
icon on my Control Panel. The virtual media function only supports the Windows
browser and AP client programs.
Problem Resolution
The Log Server program does
not run. The Log Server requires the Microsoft Jet OLEDB 4.0
driver in order to access the database.
This driver is automatically installed with Windows
ME, 2000 and XP.
For Windows 98 or NT, you will have to go to the
Microsoft download site:
http://www.microsoft.com/data/download.htm
to retrieve the driver file:
MDAC 2.7 RTM Refresh (2.70.9001.0)
Since this driver is used in Windows Office Suite, an
alternate method of obtaining it is to install Windows
Office Suite. Once the driver file or Suite has been
installed, the Log Server will run.
ip8000.book Page 87 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
88
Sun Systems
*These solutions work for most common Sun VGA cards. If using them fails
to resolve the problem, consult the Sun VGA card's manual.
Problem Resolution
Video display problems with
HDB15 interface systems (e.g.,
Sun Blade 1000 servers).1
The display resolution should be set to 1024 x 768:
Under Text Mode:
1. Go to OK mode and issue the following
commands:
setenv output-device screen:r1024x768x60
reset-all
Under XWindow:
1. Open a console and issue the following command:
m64config -res 1024x768x60
2. Log out
3. Log in
Video display problems with
13W3 interface systems (e.g.,
Sun Ultra servers).*
The display resolution should be set to 1024 x 768:
Under Text Mode:
1. Go to OK mode and issue the following
commands:
setenv output-device screen:r1024x768x60
reset-all
Under XWindow:
1. Open a console and issue the following command:
m64config -res 1024x768x60
2. Log out
3. Log in
The local and remote mouse
pointers do not sync For USB mice on Windows systems. the local and
remote mouse pointers are designed to automatically
sync when you connect. For other mice and computer
platforms, you must select Manual as the Mouse
Sync Mode choice, and sync the pointers manually.
See Mouse Sync Mode, page 30 for further details.
ip8000.book Page 88 Friday, May 9, 2008 10:39 AM
Appendix
89
Additional Mouse Synchronization Procedures
If the mouse synchronization procedures mentioned in the manu al fail to
resolve mouse pointer problems for particular compu ters, try the followi ng:
Windows:
Note: In order for the local and remote mice to synchronize, you must use the
generic mouse driver supplied with the MS operating system. If you
have a third party driver installed - such as one supplied by th e mouse
manufacturer - you must remove it.
1. Windows 2000:
a) Open the Mouse Properties dialog box (Control Panel → Mouse →
Mouse Properties)
b) Click the Motion tab
c) Set the mouse speed to the middle position (6 un its in from the left)
d) Set the mouse acceleration to None
ip8000.book Page 89 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
90
2. Windows XP / Windows Server 2003:
a) Open the Mouse Properties dialog box (Control Panel → Mouse)
b) Click the Pointer Option s tab
c) Set the mouse speed to the middle position (6 units in from the left)
d) Disable Enhance Pointer Precision
3. Windows ME:
Set the mouse speed to the middle position; disable mouse acceleration
(click Advanced to get the dialog box for this).
4. Windows NT / Wi ndows 98 / Windows 95:
Set the mouse speed to the slowest position.
Sun / Linux
Open a terminal session and issue the foll o w ing command:
Sun: xset m 1
Linux: xset m 0
ip8000.book Page 90 Friday, May 9, 2008 10:39 AM
Appendix
91
Trusted Certificates
Overview
When you try to log in to the device from your bro wser, a Security Al ert
message appears to inform you that the device’s certificate is not trusted, and
asks if you want to proceed.
The certificate can be trusted, but the alert is triggered because the certificate’s
name is not found on Microsoft’s list of Trusted Authorities. You have two
options: 1) you can ignore the warning and click Yes to go on; or 2) you can
install the certificate and have it be recognized as trusted.
If you are working on a computer at another location, accept the certificate
for just this session by clicking Yes.
If you are working at your own computer, install the certificate on your
computer (see below for details). After the certificate is installed, it will be
recognized as trusted.
ip8000.book Page 91 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
92
Installing the Certificate
To install the certificate, do the following:
1. In the Security Alert dialog box, click View Certificate. The Certificate
Information dialog box appears:
Note: There is a red and white X logo over the certifica te to indicate that it is
not trusted.
2. Click Install Certificate.
3. Follow the Installation Wizard to complete the installation. Unless you
have a specific reason to choose otherwise, accept the default options.
4. When the Wizard presents a caution screen:
Click Yes.
5. Next, click Finish to complete the installation ; then click OK to close the
dialog box.
ip8000.book Page 92 Friday, May 9, 2008 10:39 AM
Appendix
93
Certificate Trusted
The certificate is now trusted:
When you click View Certificate, you can see that the red and white X logo is
no longer present – further indication that the certificate is trusted:
ip8000.book Page 93 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
94
About SPHD Connectors
Limited Warranty
ALTUSEN warrants this product against defects in material or workmanship for a period of one
(1) year from the da te of purchase. If this product proves to be defective, contact ALTUSEN's
support department for repair or replacement of your unit. ALTUSEN will not issue a refund.
Return requests can not be proces sed without the original proof of purchase.
When returning the product, you mu st ship the product in its original packaging or packaging that
gives an equal degree of protection. Include your proof of purchase in the packag ing and the RMA
number clearly marked on the outside of the package.
This warranty becomes invalid if the factory-supplied serial number has been removed or altered
on the product.
This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse,
abuse, negligence or modification of any part of the pr oduct. This warranty does not cover damage
due to improper operation or maintenance, connection to improper equipment, or attempted repair
by anyone other than ALTUSEN. This warr anty does not cover products sold AS IS or WITH
FAULTS.
IN NO EVENT SHALL ALTUSEN'S LIAB ILITY EXCEED THE PRICE PAID FOR THE
PRODUCT. FURTHER, ALTUSEN SHALL NOT BE RESPONSIBLE FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS
DOCUMENTATION. ALTUSEN SHALL NOT IN ANY WAY BE RESPONSIBLE FOR,
WITHOUT LIMITATION, LOSS OF DATA, LOSS OF PROFITS, DOWNTIME, GOODWILL,
DAMAGE OR REPLACEMENT OF EQUIPMENT OR PROPERTY, AND ANY EXPENSES
FROM RECOVERY, PROGRAMMING, AND REPRODUCTION OF ANY PROGRAM OR
DATA.
ALTUSEN makes no warranty or representation, expressed, implied, or statutory with respect to
its products, contents or use of this documentation and all accompanying software, and specifically
disclaims its quality, performance, merchantability, or fitness for any particular purpose.
ALTUSEN reserves the right to revise or update its product, software or documentation without
obligation to notify any individual or entity of such revisions, or update.
For details about extended warranties, please contact one of our dedicated value added resellers.
This product uses SPHD connectors for its KVM and/or
Console ports. We have specifically modified the shape of these
connectors so that only KVM cables that we have designed to
work with this product can be connected.
ip8000.book Page 94 Friday, May 9, 2008 10:39 AM
95
Index
A
Access Ports, 19
Administration, 17
ANMS, 24
Customization, 29
Firmware up grading, 31
General, 18
Network, 19
Security, 21
Administrator Login Failure, 85
Administrator Utility, 70
ANMS, 24
settings, 73
AP Operation, 65
Java Client, 77
Windows Client, 65
B
Browser screen elements, 14
C
CC Management, 26
Control Panel
Java Applet, 46
Windows Client, 35
Corrupt Password, 85
Customization, 29
settings, 75
D
DNS Server, 20
F
Features, 2
Filtering, 21
IP, 22
MAC, 23
Firmware
Upgrading, 75
upgrading, 76
Firmware upgrading, 31
Forgotten Passw ord , 85
G
General, 18
settings, 70
H
Hardware Setup
Basic Installation, 7
Feature Cable Installation, 9
Hotkey Setup
Java Applet, 48
Windows Client, 37
Hotkeys
Windows Client, 37, 48
I
Installation, 7
basic, 7
feature cabl e , 9
Invalid login, 13
IP Address, 20
IP address determi nation, 83
IP Filtering, 22
J
Java Applet
Navigation, 46
Java Client
AP Version, 77
Troubleshooting, 87
ip8000.book Page 95 Friday, May 9, 2008 10:39 AM
IP8000 User Manual
96
L
Layout Diagram, 5
Lock Key LEDs, 47, 53
Log File, 55
Main Screen, 55
Log file, 55
Log Server, 1
Configure, 59
Events, 60
Installation, 57
KN9108/KN9116 Main
Screen, 63
Main Screen, 58
Maintenance, 61
Menu Bar, 59
Options, 62
Search, 60
Settings, 26
Starting Up, 58
Tick Panel, 64
Troubleshooting, 87
Logging In, 11
Logging in
AP program, 68, 78
Login
Failure, 29
Invalid login, 13
M
MAC Address, 18
MAC filtering, 23
Message Board
Java Applet, 51
Windows Client, 42
Mouse Synchronization, 89
Mouse synchronization
Windows, 89
N
Network, 19
settings, 71
Network environment, 71
O
Online
Registration, iii
Overview, 1
R
RADIUS, 24
Access Rights Examples, 25
Requirements
Operating Systems, 4
OS Support, 4
RoHS, ii
S
Safety Instructions
General, 79
Screen Elements, 14
Security, 21
settings, 72
Serial number, 66, 77
Settings Notebook
ANMS, 73
Customization, 75
General, 70
Network, 71
Security, 72
User Management, 74
SJ/T 11364-2006, ii
System Requirements, 3
T
Technical Support, 81
Telephone support, iii
Tick Panel, 64
ip8000.book Page 96 Friday, May 9, 2008 10:39 AM
Index
97
Time out cont ro l, 29
Troubleshooting
Java Client, 87
Log Server, 87
Windows Client, 86
Trusted Certificates, 91
U
Upgradi ng fi rmw a r e, 75
Upgrading the Firmware, 76
User Management, 74
Administration
User Management,27
User management
settings, 74
User Notice, iii
User Station filtering
MAC, 23
V
Video Settings
Java Applet, 50
Windows Client, 39
Virtual Media, 40
W
Windows Client, 1, 33
AP Version, 65
Installation, 57, 65
Navigation, 34
Starting up, 33
Troubleshooting, 86
ip8000.book Page 97 Friday, May 9, 2008 10:39 AM