Table of Contents
ATEN VC486-AT-G User Manual
Displayed below is the user manual for VC486-AT-G by ATEN which is a product in the Video Signal Converters category. This manual has pages.
Related Manuals
ATEN VanCryst™
VC486
12G-SDI to HDMI Converter
User Manual
VC486 User Manual
ii
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
KCC Statement
VC486 User Manual
iii
HDMI Trademark Statement
The terms HDMI, HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc.
RoHS
This product is RoHS compliant.
VC486 User Manual
iv
About this Manual
This user manual is provided to help you get the most from the VC486 unit. It
covers all aspects of installation, configuration, and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction introduces you to the 12G-SDI to HDMI
Converter. Its purpose, features, installation considerations, and panel
components are presented and described.
Chapter 2, Hardware Setup describes the steps that are necessary to
quickly and safely set up your installation.
Chapter 3, Operation explains the audio channel selection using the audio
channel switch and how to remote manage and control tasks via the ATEN
VC486 Configuration Software.
Chapter 4, The Firmware Upgrade Utility explains the source input
operation using the source switch pushbutton and RS-232 commands and its
limitations.
Appendix provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other
technical information.
Note:
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit or any connected
devices.
ATEN regularly updates its product documentation for new features and
fixes. For an up-to-date VC486 documentation, visit
http://www.aten.com/global/en/
VC486 User Manual
v
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
>Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
>
Run means to
open the Start menu, and then select Run.
Indicates critical information.
VC486 User Manual
vi
Package Contents
1 VC486 12G-SDI to HDMI Converter
1 power adapter
1 HDMI LockPro
4 foot pads
1 user instructions
Note: Make sure that all of the components are present and in good order. If
anything is missing or was damaged in shipping, contact your dealer.
VC486 User Manual
vii
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
International http://www.aten.com
North America http://www.aten-usa.com
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
VC486 User Manual
viii
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
VC486 User Manual
ix
Table of Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
1. Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Hardware Setup
Mounting the VC486 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connecting the VC486 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3. Operation
Selecting the Audio Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SDI Audio Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ATEN VC486 Configuration Software . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the ATEN VC486 Configuration Software . . . . . . . . . . . . . . 11
Connecting the VC486 to Your PC . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Opening the ATEN VC486 Configuration Software . . . . . . . . . . . . . . 14
Page Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Top Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Device List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Side Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. The Firmware Upgrade Utility
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 23
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VC486 User Manual
x
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Supported SDI Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1
Chapter 1
Introduction
Overview
The VC486 is a 12G-SDI to HDMI Converter that converts HD/3G/6G/12G-
SDI input signals to an HDMI output in real time. It supports various
transmission distances depending on different SDI formats, including 45 m
(12G-SDI), 60 m (6G-SDI), 90 m(3G-SDI), and 150 m (HD-SDI), offering the
flexibility for professional video projects. The VC486 is a perfect choice for
applications such as using HDMI televisions as SDI broadcast monitors, and
connecting to video projectors.
Chapter 1. Introduction
2
Features
Converts HD/3G/6G/12G-SDI input signals to an HDMI output in real
time
SDI signal re-clocked for high signal quality
Supports SDI standard SMPTE-292/424/425-3/2081/2082
Supports an SDI distance of up to 45 m (12G-SDI), 60 m (6G-SDI), 90 m
(3G-SDI) and 150 m (HD-SDI)
Supported SDI formats:
HD-SDI (SMPTE 292M, 296M, up to 1.485 Gbps)
3G-SDI (SMPTE 424M, 425M level A and B, up to 2.97 Gbps)
6G-SDI (SMPTE 2081-1, SMPTE 2081-10, up to 6 Gbps)
12G-SDI (SMPTE 2081-1, SMPTE 2081-10, SMPTE 2082-1 and
SMPTE 2082-10, up to 12 Gbps)
Supports analog stereo audio output with RCA (R/L) connector
Automatic detection of input video signals
Analog Audio channel selection with a 8-step rotary switch
ATEN VC486 Configuration Software for advanced configuration
Locking power connector
VC486 User Manual
3
Planning the Installation
Requirements
Prepare the following before installing the VC486 unit:
1 SDI source service
1 SDI source output device
2 SDI cables
1 HDMI cable
1 HDMI display
1 speakers
Considerations
The maximum transmission distance varies at different parts of the
transmission:
Connection Interface Distance
SDI source to the VC486 12G – SDI 45 m
6G – SDI 60 m
3G – SDI 90 m
HD – SDI 150 m
VC486 to the display 12G – SDI 45 m
6G – SDI 60 m
3G – SDI 90 m
HD – SDI 150 m
HDMI 3 m
Chapter 1. Introduction
4
Components
Front View
No. Component Description
1 HDMI output
status LED
The LED lights green to indicate the HDMI signal is stable.
2 SDI input status
LED
The LED lights green to indicate the SDI signal is stable.
3 power LED
The LED lights green to indicate the unit is receiving power.
123
VC486 User Manual
5
Rear View
No. Component Description
1 power jack Connects to the power adapter.
2 firmware upgrade port Connects to a USB
Micro-B cable for firmware
upgrade. See The Firmware Upgrade Utility,
page 23.
3 audio channel switch Use the switch to set an audio channel from 0 - 7.
See Selecting the Audio Channel, page 9.
4 HDMI out port Connects to the HDMI in port on the display device.
5 SDI input port Connects to the SDI out port on the source device.
6 SDI output port Connects to the SDI in port on the display device.
7 audio output ports Connects to the audio in port on a speaker.
4
1237
56
Chapter 1. Introduction
6
This Page Intentionally Left Blank
7
Chapter 2
Hardware Setup
Mounting the VC486 Unit
You can mount the VC486 on a rack.
Rack Mounting
Use the VE-RMK 1U Rack Mount Kit to rack-mount the VC486. For more
information about this accessory, go to www.aten.com/products
1. Please review the safety information regarding the placement of
this device in Safety Instructions, page 29.
2. Do not power on the VC486 until all the necessary hardware is
connected.
Chapter 2. Hardware Setup
8
Connecting the VC486 Unit
Follow the steps below to connect the VC486 to a source, and other controls as
required.
1. Ground the VC486 by connecting one end of a grounding wire to the
Grounding Terminal and the other end to a suitable grounded object. The
Grounding Terminal is located on the left side of the unit.
Note: Do not omit this step. Proper grounding helps to prevent damage to
the unit from power surges or static electricity.
2. Use an HDMI cable to connect an HDMI-enabled monitor to the HDMI
output port on the VC486.
3. Use a coaxial cable to connect an SDI source device to the SDI input port
on the VC486.
4. Use a coaxial cable to connect an SDI display device or SDI router to the
SDI output port on the VC486.
5. Connect your audio output device (e.g. speakers) to the audio output ports
on the VC486.
6. Plug the provided power adapter into an appropriate power source; plug
the power adapter cable into the power jack on the VC486.
7. (Optional) To change the SDI audio output channel, use the audio channel
switch. Each number on the switch represents two channels, with 0
representing channel 1 and 2, 1 representing channel 3 and 4, etc.
8. Check that the power LED, HDMI output status LED, and SDI input status
LED light green to indicate that the VC486 is receiving power and ready
to operate.
5
2
3
4
67
SDI Router
Speakers
SDI Input Source
or
Local Monitor with
HDMI Input
Local Monitor with
Coaxial Input
1
9
Chapter 3
Operation
Selecting the Audio Channel
Switch the audio channel switch on the VC486 to switch the audio channel
from 0 - 7. Each audio chann el support 2 an alogs, see the tabl e below for more
information.
SDI Audio Selection
Switches Supported Analog
1 - 2
3 - 4
5 - 6
7 - 8
audio channel switch
Chapter 3. Operation
10
9 - 10
11 - 12
13 - 14
15 - 16
Switches Supported Analog
VC486 User Manual
11
ATEN VC486 Configuration Software
For advanced settings, such as configuration the VC486’s input, output, and
audio settings, download and install the ATEN VC486 Configuration Software
from the product web page.
Installing the ATEN VC486 Configuration Software
To install the ATEN VC486 Configuration Software on your PC, follow the
steps below.
1. Download the ATEN VC486 Configuration Software package from our
product web page and unzip the downloaded file.
2. Double-click on the ATEN VC486 Configuration Software app.
3. The ATEN VC486 Configuration Software Setup dialog box appears, and
click Install.
Chapter 3. Operation
12
4. Wait for the installation process to complete, and click Finish.
VC486 User Manual
13
Connecting the VC486 to Your PC
Use a USB Micro-B to USB Type-A cable to connect a USB Type-A port on
your computer, and the other end to the firmware upgrade port on your VC486.
Chapter 3. Operation
14
Opening the ATEN VC486 Configuration Software
Before you open the ATEN VC486 Configuration Software, make sure the
VC486 is connected to your PC.
1. Locate and double-click the ATEN VC486 Configuration Software icon
on your desktop.
2. The ATEN VC486 Configuration Software main page appears.
VC486 User Manual
15
Page Components
No. Component Description
1 Top Menu
Language: Click to select a preferred language. See
Language, page 16.
Help: Click to gain access to the user manual, FAQ,
and available firmware updates. See Help, page 16.
2 Device List Click to select an available VC486 from your PC for
configuration, or click to refresh the device list. See
Device List, page 17.
3 Side Menu Click the side menu to configure the VC486’s input, output,
audio, and info settings. See Side Menu, page 17.
4 Settings Page Allows you to configure settings for the VC486. The
content varies depending on the selected side menu.
When the configuration has been made, the Apply button
changes from grey to green .
Chapter 3. Operation
16
Top Menu
Language
Click to select a language between English, Chinese TW, Chinese CN,
Japanese, Korean, German, Spanish, French, and Russian.
Help
Click to access to the most up-to-date user manual, FAQ, and available
firmware updates.
VC486 User Manual
17
Device List
In the device list field, it allows you to select an available VC486 for
configuration by clicking , or click
to refresh the device list
.
Side Menu
The Side Menu allows you to configure input, output, audio settings, and
device name for the selected VC486.
Input
Chapter 3. Operation
18
Output
In the output configuration page, it allows you to configure the color space,
color depth, and HDCP settings.
Component Description
Color Space Sets a color space for the selected VC486 by clicking .
Color Depth Sets a color depth for the selected VC486 by clicking .
HDCP Sets to enable or disable HDCP by clicking .
VC486 User Manual
19
Audio
In the audio configuration page, it allows you to configure the HDMI audio
channel, HDMI audio selection, and analog audio selection settings.
Component Description
HDMI Audio
Channel
Sets the HDMI audio channel between 2 Channels and 8
Channels.
HDMI Audio
Selection
Sets an HDMI audio channel selection for the selected VC486 by
clicking .
Analog Audio
Selection
Sets an analog audio channel selection for the selected VC486 by
clicking .
Chapter 3. Operation
20
Info
In the info configuration page, it allows you to configure the device name for
the selected VC486, and view its firmware version.
Reset
To reset the selected VC486 to its factory default settings, click Reset.
VC486 User Manual
21
A warning message appears, and click OK.
Chapter 3. Operation
22
This Page Intentionally Left Blank
23
Chapter 4
The Firmware Upgrade Utility
Introduction
The purpose of the Windows-based Firmware Upgrade Utility is to provide an
easy process for upgrading the VC486. The program comes as part of a
Firmware Upgrade Package that is specific for each device.
As new firmware versions become available, new firmware upgrade packages
are posted on our website. Check the website regularly to find the latest
information and packages.
Downloading the Firmware Upgrade Package
To download the firmware upgrade package:
1. On our Website go to: Download - Firmware and choose the device
model, or from the VC486 product page under the Resources tab, select
Firmware. A list of available firmware upgrade packages appears.
2. Choose the firmware upgrade package that you wish to install (usually the
most recent) and download it to your computer.
Chapter 4. The Firmware Upgrade Utility
24
Preparation
To prepare for the firmware upgrade, do the following:
1. Unplug the VC486’s power adapter.
2. Use a USB Micro-B to USB Type-A cable to connect a USB Type-A port
on your computer, and the other end to the firmware upgrade port on your
VC486.
3. Plug the power adapter into power jack on the VC486.
4. If successful, the SDI, HDMI, and power status LEDs will start to flash.
Now, you can start the upgrade process as explained on the next page.
VC486 User Manual
25
Starting the Upgrade
To upgrade the firmware:
1. Run the downloaded firmware upgrade package file either by double-
clicking the file icon, or by opening a command line and entering the full
path to it.
The Firmware Upgrade Utility welcome screen appears:
Note: The screens shown in this section are for reference only. The wording
and layout of the actual screens put up by the Firmware Upgrade Utility
may very slight from these examples.
2. Read and Agree to the License Agreement (click the I Agree radio button).
Chapter 4. The Firmware Upgrade Utility
26
3. Click Next to continue. The Firmware Upgrade Utility main screen
appears. The devices capable of being upgraded are listed in the Device
List panel:
4. Click Next to perform the upgrade. The Status LEDs SDI, HDMI, and
power will flash while the upgrade is in process.
If you enabled Check Firmware Version, the Utility compares the device's
firmware level with that of the upgrade files. If it finds that the device's
version is higher than the upgrade version, it brings up a dialog box
informing you of the situation and gives you the option to continue or
cancel.
If you didn't enable Check Firmware Version, the Utility installs the
upgrade files without checking whether they are a higher level, or not.
Status messages appear in the Status Messages panel, and the progress
toward completion is shown on the Progress bar.
VC486 User Manual
27
Upgrade Succeeded
After the upgrade has completed, all port LEDs will stop flashing and a screen
appears to inform you that the procedure was successful:
Click Finish to close the Firmware Upgrade Utility.
Upgrade Failed
If the Upgrade Succeeded screen doesn't appear, it means that the upgrade
failed to complete successfully. See the next section, Firmware Upgrade
Recovery, for how to proceed.
Chapter 4. The Firmware Upgrade Utility
28
Firmware Upgrade Recovery
There are three conditions that call for firmware upgrade recovery:
When a firmware upgrade is manually aborted.
When the mainboard firmware upgrade fails.
When the I/O firmware upgrade fails.
To perform a firmware upgrade recovery, do the following:
1. Power off the device.
2. Connect the USB Micro-B to USB Type-A cable to the USB Type-A port
on your computer, and the other end to the firmware upgrade port of your
VC486.
3. Repeat the upgrade procedure.
29
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
To prevent damage to your installation it is important that all devices are
properly grounded.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Appendix
30
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
VC486 User Manual
31
Rack Mounting
Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflow is provided to devices in the rack.
Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer.
Do not step on or stand on any device when servicing other devices in a
rack.
Appendix
32
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://support.aten.com
For telephone support, see Telephone Support, page vii:
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase
Your computer configuration, including operating system, revision level,
expansion cards, and software
Any error messages displayed at the time the error occurred
The sequence of operations that led up to the error
Any other information you feel may be of help
Email Support support@aten-usa.com
Online Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
VC486 User Manual
33
Specifications
Function VC486
Switches
Audio Selection 1 x Rotary Switch (8-steps)
Control
USB 1 X Micro USB (Firmware Upgrade)
Video Input
Interfaces 1 x SDI (BNC Connector, Inter-locked Socket)
Impedance 75 Ώ
Video Output
Interfaces 1 x HDMI Type A Female (Black)
1 x SDI (BNC Connector, Inter-locked Socet)
Impedance HDMI: 100Ώ
SDI: 75 Ώ
Video
Max. Data Rate 12 Gpbs
Supported Resolutions 720p50, 720p59.94, 720p60 1080p23.98, 1080p24,
1080p25, 1080p29.97, 1080p30, 1080p50, 1080p59.94,
1080p60 , 1080PsF25, 1080PsF29.97, 1080PsF30 1080i50,
1080i59.94, 1080i60
2K DCI 23.98p, 2K DCI 24p, 2K DCI 25p, 2K DCI 25PsF:
2160p23.98, 2160p24, 2160p25, 2160p29.97, 2160p30,
2160p50, 2160p59.94, 2160p60, 4K DCI 23.98p
4K DCI 24p, 4K DCI 25p
Max. Distance [12G-SDI] up to 45 m
[6G-SDI] up to 60 m
[3G-SDI] up to 90 m
[HD-SDI] up to 150 m
HDMI up to 3 m (3840 x 2160 @ 60Hz)
Audio
Output 1 x HDMI Type A Female (Black)
2 x RCA Connector Female (R/L, Analog Audio)
Format Compliance with HDMI and Audio 2 CH
Appendix
34
SDI Formats
SDI Formats HD-SDI (SMPTE 292M, 296M, up to 1.485 Gbps)
3G-SDI (SMPTE 424M, 425M Level A and B, up to 2.97
Gbps)
6G-SDI (SMPTE 2081-1, SMPTE 2081-10, up to 6 Gbps)
12G-SDI (SMPTE 2081-1, SMPTE 2081-10, SMPTE 2082-1,
and SMPTE 2082-10, up to 12Gbps)
Connectors
Power 1 x DC 5V 3A, Lockable
Power
Consumption DC5V; 5.69W; 27BTU
Environmental
Operating Temperature 0 - 40°C
Storage Temperature -20 - 60°C
Humidity 0 - 80% RH, Non-Condensing
Physical Properties
Housing Metal
Weight 0.65 kg (1.43 lb)
Dimensions (L x W x H) 18.20 x 12.96 x 2.87 cm (7.17 x 5.10 x 1.13 in.)
Function VC486
VC486 User Manual
35
Supported SDI Resolutions
The VC486 supports the following SDI resolutions:
Video Format Resolution Color Space Scan Frequency
(Hz)
HD 720p YCbCr-422-10bit 25
29.97
30
50
59.94
60
1080i 50
59.94
60
1080sF 23.98
24
25
29.97
30
1080p 23.98
24
25
29.97
30
Appendix
36
3GA 1080p YCbCr-422-10bit 47.95
48
50
59.94
60
YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
23.98
24
25
29.97
30
720p YCbCr-444-10bit
RGB-444-10bit
25
29.97
30
50
59.94
60
1080i YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
50
59.94
60
1080sF YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
23.98
24
25
29.97
30
Video Format Resolution Color Space Scan Frequency
(Hz)
VC486 User Manual
37
3GB-DL 1080p YCbCr-422-10bit 47.95
48
50
59.94
60
YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
23.98
24
25
29.97
30
1080i YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
50
59.94
60
1080sF YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
23.98
24
25
29.97
30
6G 1080p YCbCr-444-10bit
RGB-444-10bit
50
59.94
60
2160p YCbCr-422-10bit 23.98
24
25
29.97
30
12G 2160p YCbCr-422-10bit 47.95
48
50
59.94
60
YCbCr-444-10bit
RGB-444-10bit
YCbCr-444-12bit
RGB-444-12bit
YCbCr-422-12bit
23.98
24
25
29.97
30
Video Format Resolution Color Space Scan Frequency
(Hz)
Appendix
38
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in
materials and workmanship for a Warranty Period of two [2] years (warranty
period may vary in certain regions/countries) commencing on the date of
original purchase. This warranty period includes the LCD panel of ATEN LCD
KVM switches. Select products are warranted for an additional year (see A+
Warranty for further details). Cables and accessories are not covered by the
Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty
Period. If a product is detective, ATEN will, at its discretion, have the option
to (1) repair said product with new or repaired components, or (2) replace the
entire product with an identical product or with a similar product which fulfills
the same function as the defective product. Replaced products assume the
warranty of the original product for the remaining period or a period of 90 days,
whichever is longer. When the products or components are replaced, the
replacing articles shall become customer property and the replaced articles
shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
© Copyright 2021 ATEN® International Co., Ltd.
Released: 2021-08-24
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.