Table of Contents
ATEN VE1843 User Manual
Displayed below is the user manual for VE1843 by ATEN which is a product in the AV Extenders category. This manual has pages.
Related Manuals
ATEN VanCryst™
VE1843
True 4K HDMI / USB
HDBaseT 3.0 Transceiver
User Manual
VE1843 User Manual
ii
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
Suggestion
Shielded twisted pair (STP) cables must be used with the unit to ensure
compliance with FCC & CE standards.
KCC Statement
VE1843 User Manual
iii
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
HDMI Trademark Statement
The terms HDMI, HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc.
RoHS
This product is RoHS compliant.
VE1843 User Manual
iv
About this Manual
This user manual is provided to help you get the most from the VE1843 unit.
It covers all aspects of installation, configuration, and operation. An overview
of the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the VE1843 system. Its purpose,
features, and installation considerations are described.
Chapter 2, Hardware Setup, describes the panel components of the VE1843
and detail steps to quickly and safely set up your installation.
Chapter 3, Operation, explains how to use the Tx and Rx switch, and how
to set up the input detection mode using the a pushbutton and RS-232
commands.
Appendix, provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other
technical information regarding the VE1843.
Note:
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit or any connected
devices.
ATEN regularly updates its product documentation for new features and
fixes. For an up-to-date VE1843 documentation, visit
http://www.aten.com/global/en/
VE1843 User Manual
v
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
>
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
>
Run means to
open the Start menu, and then select Run.
Indicates critical information.
VE1843 User Manual
vi
Package Contents
1 VE1843 True 4K HDMI / USB HDBaseT 3.0 Transceiver
1 RS-232 terminal block
1 foot pad set (4 pcs)
1 USB Type-B to USB Type-A cable
1 power adapter
1 IR emitter
1 IR receiver
1 user instructions
Note:
Make sure that all of the items are present and in good order. If
anything is missing or was damaged in shipping, please contact your
dealer for further assistance.
Features may have been added to the VE1843 since this manual was
published. Please visit our webiste to download the most up-do-date
version of the manual.
VE1843 User Manual
vii
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
International http://www.aten.com
North America http://www.aten-usa.com
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
VE1843 User Manual
viii
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
VE1843 User Manual
ix
Table of Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
1. Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Source Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Hardware Setup
Mounting the VE1843 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VE1843 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VE1843 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
VE1843 Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RS-232 Channel Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3. Operation
Tx and Rx Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
HDMI Audio Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Audio Embedding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Audio De-embedding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Bypassing Audio Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VE1843 User Manual
x
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1
Chapter 1
Introduction
Overview
The VE1843 is ATEN’s first video transceiver and integrates the functions of
a transmitter and a receiver into one unit. This combination allows users to
easily configure the unit to be a transmitter or receiver depending on their AV
solution, and to enjoy more flexible deployment and effective use with video
matrix switches, video splitters, etc.
Designed with HDBaseT 3.0 technology, the VE1843 not only extends True
4K uncompressed signals up to 100 m over a single Cat 6a cable (HDBaseT
3
Certified Cat 6a cable) with zero latency, but also transmits IR, RS-232,
Ethernet, independent audio, and USB signals with the latest HDBaseT
standards. For stable HDMI signal transmission, the VE1843 ensures high-
quality visuals and reliable extension by supporting HDCP 2.2, 3D, Deep
Color, and HDR. In addition, the VE1843 is equipped with HDMI audio
embedded / de-embedded functions, enabling users to flexibly adapt suitable
audio / video combinations based on different environments. To ensure non-
stop operations, the fanless fin heat sink design prevents overheating and thus
elevates its reliability.
Empowered by the above benefits, the VE1843 increases the potential of AV
applications while also streamlining complex installations. This makes the
VE1843 an ideal solution for conference halls, auditoriums, lecture halls,
museums, exhibition rooms, and anywhere else that requires high-quality
transmission and easy-to-use application.
Chapter 1. Introduction
2
Features
Extends uncompressed True 4K HDMI signals up to 100 m over a single
Cat 6a cable (HDBaseT
3
Certified Cat 6a cable) with zero latency
Flexible for deployment — can be configured as a transmitter or receiver
depending on the AV solution
Compliant with HDBaseT 3.0 standards — transmits high-quality video,
full range IR, bi-directional RS-232, Gigabit Ethernet, independent stereo
audio and USB 2.0 signals channel bypass
HDMI (3D, Deep Color, 4K/60Hz); HDCP 2.2 compliant
Superior video quality — up to 4096 x 2160 @ 60 Hz (4:4:4); HDR
supported
Supports HDMI audio embedding / de-embedding functions
Supports HDMI local output
Compliant with the USB 2.0 standard for a wide range of USB peripherals
compatibility
LED indication of HDBaseT and HDMI signal status for easier
recognition
Fanless fin heat sink enclosure — elevates durability and reliability by
preventing overheating, fan malfunctions, and noises
Firmware upgradable
Built-in 8KV / 15KV ESD protection
Plug-and-play
Rack-mountable
VE1843 User Manual
3
Planning the Installation
Display
Up to two HDMI displays capable of the highest required resolution
Source Device
A source device with an HDMI port
Cables
2 HDMI cables
To connect the VE1843 transmitter and receiver units, we recommend
using cables of HDBaseT
3
Certified Cat 6a cable to ensure video quality.
For better video quality, we strongly suggest using ATEN 2L-2920 Cat 6a
cable (HDBaseT
3
Certified Cat 6a cable) with zero latency.
Considerations
The maximum transmission distance varies at different parts of the
transmission:
Note: The maximum transmission distance for True 4K resolution using
an ATEN 2L-2920 Cat 6a cable (HDBaseT
3
Certified Cat 6a cable )
with zero latency is 100 m. This cable is currently unavailable for
purchase and will be sold separately in the future.
Connection Interface Resolution Distance
Computer to the VE1843 Transmitter HDMI True 4K 5 m
The VE1843 Transmitter to a VE1843
Receiver (R) or a compatible ATEN
HDBaseT Receiver
HDBaseT
3
Certified Cat 6a
cable) with zero
latency
True 4K 100 m*
VE1843 Receiver to a display HDMI True 4K 5 m
Chapter 1. Introduction
4
This Page Intentionally Left Blank
5
Chapter 2
Hardware Setup
Mounting the VE1843 Unit
You can mount the VE1843 to the wall or on a rack.
Wall Mounting
Secure or hang the VE1843 unit to the wall using the built-in mounting
brackets.
Rack Mounting
Use the VE-RMK 1U Rack Mount Kit to rack mount the VE1843. For more
information about this accessory, go to www.aten.com/products
1. Please review the safety information regarding the placement of
this device in Safety Instructions, page 15.
2. Do not power on the VE1843 until all the necessary hardware is
connected.
Chapter 2. Hardware Setup
6
Hardware Overview
VE1843 Front View
No. Component Description
1 HDBaseT long reach
mode switch (reserved)
Sets to enable the long reach mode. This switch is
currently reserved for future expansion.
2 HDMI audio switch Sets to enable the embed and de-embed functions.
See Tx and Rx Switch, page 13.
3 RS-232 Port Connects to an RS-232 serial controller, such as a
PC or a control system.
4 HDBaseT port Connects to an HDBaseT
3
Certified Cat 6a cable
with zero latency to transmit HDMI and control
signals to the connected receiver if the unit is set to a
transmitter.
5 cable lock screw for ATEN
LockPro
TM
Universal HDMI cable lock that provides the easiest
way to secure an HDMI cable to most HDMI devices.
6 audio in Connects to an audio source device, such as a PC.
7 USB Type-B port Connects to source device, such as a PC.
8 firmware upgrade switch
(reserved)
This switch is reserved for ATEN Technical Support.
If you would like to do a firmware upgrade yourself,
please contact your dealer.
9 Tx / Rx switch Sets to define the unit as a transmitter or a receiver.
10 HDMI in Connects to an HDMI video source device using an
HDMI cable.
1098
321 4 5 6 7
VE1843 User Manual
7
VE1843 Rear View
No. Component Description
1 USB Type-A port Connects to a peripheral device, such as a keyboard
or mouse.
2 cable lock screw for ATEN
LockPro
TM
Universal HDMI cable lock that provides the easiest
way to secure an HDMI cable to most HDMI
devices.
3 audio out Connects to an audio output device, such as a set of
speakers.
4 Ethernet port Connects to a network switch to provide Internet
access for the connected source device using an
RJ-45 cable.
5 IR port Connects to an IR emitter or IR receiver for remotely
control using an IR remote control.
6 power jack Connects to a power adapter for power supply.
7 HDMI out Connects to a HDMI display device using an HDMI
cable.
7
321 4 5 6
Chapter 2. Hardware Setup
8
VE1843 Top View
No. Component Description
1 grounding terminal Grounds the unit to a suitable grounded object.
Transmitter LEDs
2 power LED Lights green: The unit is receiving power.
Off: The unit is powered off.
3 link LED Lights orange: The transmission between the
transmitter and receiver is stable.
Blinks orange: The transmission between the
transmitter and receiver is unstable.
Off: There is no transmission between the
transmitter and receiver.
4 HDMI in LED Lights orange: The video display is normal with the
HDCP key.
Blinks orange: The video display is normal without
the HDCP key.
Off: There is no video signal.
Receiver LEDs
64321 75
VE1843 User Manual
9
5 HDMI out LED Lights orange: The video display is normal with the
HDCP key.
Blinks orange: The video display is normal without
the HDCP key.
Off: There is no video signal.
6 link LED Lights orange: The transmission between the
transmitter and receiver is stable.
Blinks orange: The transmission between the
transmitter and receiver is unstable.
Off: There is no transmission between the
transmitter and receiver.
7 power LED Lights green: The unit is receiving power.
Off: The unit is powered off.
No. Component Description
Chapter 2. Hardware Setup
10
Hardware Installation
Follow the steps below to safely install the VE1843 to a source, a display
device, and other devices as required.
1. Ground the VE1843 by connecting one end of a grounding wire to the
grounding terminal and the other end to a suitable grounded object.
Note: Do not omit this step. Proper grounding helps to prevent damage to
the unit from power surges or static electricity.
2. Important: Before connecting the VE1843, please set the Tx / Rx switch
to define the unit. The VE1843 will be a transmitter if the Tx / Rx switch is
set to Tx, or the VE1843 will be a receiver if the Tx / Rx switch is set to
Rx.
1
Note: The illustrated installation is
based on two VE1843 units.
RS-232 Audio USBHDMI HDMI
Audio
Ethernet IR
Set to Tx
VE1843 Transmitter
VE1843 Receiver
Power
Power
IR
Ethernet
RS-232
Set to Rx
HDBaseT3
!
Local
Output
HDMIUSB
VE1843
(Front)
VE1843
(Rear)
VE1843
(Front)
VE1843
(Rear)
VK Control System
13
2345
7
9
610
14
2
13 11 12 810 914
VE1843 User Manual
11
3. Connect an HDMI-enabled PC to the transmitter using an HDMI cable.
You can connect other HDMI-enabled source device here (e.g., Blu-ray
player).
4. (Optional) Connect an audio source device (e.g., PC) to the transmitter. To
embed this audio input to the HDMI output, put the HDMI audio switch
(on Tx) to ON.
5. Connect the USB Type-B port of the transmitter to a USB host (e.g., PC).
6. Connect an HDMI-enabled display device to the transmitter using an
HDMI cable.
7. Connect the HDBaseT ports of the transmitter and receiver with a
HDBaseT
3
Certified Cat 6a cable (or above).
8. (Optional) Connect your speakers or audio amplifier to the receiver. To de-
embed this HDMI audio from the HDMI output, put the HDMI audio
switch (on Rx) to ON.
9. (Optional) To remotely control a device connected to the receiver, for
example, a TV, connect the IR emitter to the IR port of the receiver, and
the IR receiver to the IR port of the transmitter, and vice versa.
Note: The unit supports bi-directional IR transmission.
10. (Optional) To provide network connectivity for your PC, connect the
receiver to a network switch, and then connect the Ethernet port of the
transmitter to your PC.
Note: The unit supports bi-directional bypass transmission.
11. (Optional) Connect the USB Type-A port to a USB peripheral.
12. Connect an HDMI-enabled display device to the receiver using an HDMI
cable.
13. (Optional) To remotely control a PC through serial controller, connect the
RS-232 port of the transmitter to a serial controller, and then connect the
RS-232 port of the receiver to a PC, and vice versa.
Note: The unit supports bi-directional bypass transmission.
14. Connect the power cord and the power adapter, and then plug the power
adapter cables into the power jack on the units.
15. Power on all connected devices.
Chapter 2. Hardware Setup
12
RS-232 Channel Transmission
You can manage the connected devices via RS-232 serial devices, such as
computers or bar code scanners. The RS-232 signal transmission flow can be
illustrated as follows:
The general concept here is that a RS-232 signal can be transmitted (Tx) to the
receiving (Rx) end of a unit. The received signal can then be transmitted (Tx)
to the receiving (Rx) end of another unit. The RS-232 signals can be
transmitted back the other way.
PIN
CONFIGURATION
(Captive screw
connectors) Tx
Rx
Gnd
Tx
Rx
Gnd
Tx
Rx
Gnd
Tx
Rx
Gnd
S
Cat 5e/6/6a/7 cable
Transimitter
Receiver
13
Chapter 3
Operation
Tx and Rx Switch
Use the Tx / Rx switch to set the unit as a transmitter or receiver as needed.
HDMI Audio Switch
Audio Embedding
To embed the audio signals, follow the steps below.
1. Set the HDMI audio switch on the VE1843 transmitter to On.
2. Set the HDMI audio switch on the VE1843 receiver to Off.
Audio De-embedding
To de-embed the audio signals, follow the steps below.
1. Set the HDMI audio switch on the VE1843 transmitter to Off.
2. Set the HDMI audio switch on the VE1843 receiver to On.
Tx / Rx switch
HDMI audio switch
VE1843 User Manual
14
Bypassing Audio Signals
To bypass the audio signals, follow the steps below.
1. Set the HDMI audio switch on the VE1843 transmitter to Off.
2. Set the HDMI audio switch on the VE1843 receiver to Off.
Note: By default, the HDMI audio switch on the VE1843 is set to Off.
15
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
To prevent damage to your installation it is important that all devices are
properly grounded.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
Appendix
16
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
VE1843 User Manual
17
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://support.aten.com
For telephone support, see Telephone Support, page vii.
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase
Your computer configuration, including operating system, revision level,
expansion cards, and software
Any error messages displayed at the time the error occurred
The sequence of operations that led up to the error
Any other information you feel may be of help
Email Support support@aten-usa.com
Online Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
Appendix
18
Specifications
Function VE1843
Video Input
Interfaces 1 x HDMI Type-A Female (Black)
Impedance 100 Ώ
Max. Distance 5 m
Video Output
Interfaces 1 x HDMI Type-A Female (Black)
Impedance 100 Ώ
Max. Distance 5 m
Video
Max. Data Rate 18 Gbps (6 Gbps per Lane)
Max. Pixel Clock 600 MHz
Compliance HDMI (3D, Deep Color, 4K / 60Hz); 4K HDR
HDCP 2.2 Compatible
Max. Resolutions 4096 x 2160 @ 60Hz (4:4:4)
3840 x 2160 @ 60Hz (4:4:4)
Max. Resolutions / Distances Up to 4K x 2K @ 60Hz (4:4:4) @ 100 m (HDBaseT
3
Certified Cat 6a cable / ATEN 2L-2920 Cat 6a cable)
Audio
Input 1 x HDMI Type-A Female (Black)
1 x Stereo Audio (Mini Stereo Jack Female Green)
Output 1 x HDMI Type-A Female (Black)
1 x Stereo Audio (Mini Stereo Jack Female Green)
Connectors
Unit to Unit 1 x RJ-45 Female
Power 1 x DC Jack with locking (Black)
Control
RS-232 Channel Connector: 1 x Terminal Block, 3 Pole
Baud Rate: 19200
Data Bits: 8
Stop Bits 1
no parity and flow control
IR Channel 1 x Mini Stereo Jack Female (Black, Bi-directional )
30K ~ 56KHz full range transmission
Ethernet Channel 1 x GbE RJ-45 Female
VE1843 User Manual
19
USB Channel 1 x USB Type-B Female (White, Host)
1 x USB Type-A Female (White, Device)
Power Consumption DC12V:6.45W:40BTU
Switches
Selection 1 x Slide Switch – Tx (Transmitter) / Rx (Receiver)
Mode Selection 1 x Slide Switch – HDMI Audio Embedding or De-
embeddin ON/OFF selection
Firmware Upgrade 1 x Slide Switch - ON/OFF
Long Reach Mode 1 x Slide Switch - ON/OFF (Reserved)
LEDs
Power 1 x Tx (Green, Transmitter)
1 x Rx (Green, Receiver)
Note: The Tx or Rx LED lights to indicate which role the
VE1843 is set to.
Link 1 x Tx (Orange, Transmitter)
1 x Rx (Orange, Receiver)
Video Output 1 x Rx HDMI Out (Orange, Receiver)
Video Input 1 x Tx HDMI In (Orange, Transmitter)
Environmental
Operating Temperature 0 - 40°C
Storage Temperature -20 - 60°C
Humidity 0 x 80% RH, Non-Condensing
Physical Properties
Housing Metal
Weight 0.64 kg (1.41 lb)
Dimensions (L x W x H) 17.15 x 15.09 x 3.00 cm (6.75 x 5.94 x 1.18 in)
Function VE1843
Appendix
20
Input Resolutions 6460 x 480 @ 60/67/72/75 Hz
720 x 400 @ 70 Hz
800 x 600 @ 56/60/72/75 Hz
1024 x 768 @ 60/70/75 Hz
1280 x 800 @ 60 Hz
1280 x 1024 @ 60/75 Hz
1400 x 1050 @ 60 Hz
1400 x 900 @ 60 Hz
1600 x 1200 @ 60 Hz
1680 x 1050 @ 60 Hz
1920 x 1080/1200 @ 60 Hz
1920 x 1200 @ 60 Hz (Reduced Blanking)
1080p 60 Hz
480p 60 Hz (4:3)/(16:9)
720p 60 Hz
1080i 60 Hz
640 x 480 60 Hz (4:3)
576p 50 Hz (4:3)/(16:9)
720p 50 Hz
1080i/1080p 50 Hz
1080p 24/25/30 Hz
3840 x 2160p 24/25/30/50/60 Hz
4096 x 2160p 24/25/30/50/60 Hz
3840 x 2160p 50/60 Hz 4:2:0
4096 x 2160p 50/60 Hz 4:2:0
Function VE1843
VE1843 User Manual
21
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in
materials and workmanship for a Warranty Period of two [2] years (warranty
period may vary in certain regions/countries) commencing on the date of
original purchase. This warranty period includes the LCD panel of ATEN LCD
KVM switches. Select products are warranted for an additional year (see A+
Warranty for further details). Cables and accessories are not covered by the
Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty
Period. If a product is detective, ATEN will, at its discretion, have the option
to (1) repair said product with new or repaired components, or (2) replace the
entire product with an identical product or with a similar product which fulfills
the same function as the defective product. Replaced products assume the
warranty of the original product for the remaining period or a period of 90 days,
whichever is longer. When the products or components are replaced, the
replacing articles shall become customer property and the replaced articles
shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
© Copyright 2021 ATEN® International Co., Ltd.
Released: 2021-08-13
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.