Table of Contents
ATEN VE802 User Manual
Displayed below is the user manual for VE802 by ATEN which is a product in the AV Extenders category. This manual has pages.
Related Manuals
HDMI HDBaseT-Lite Extender with POH
VE802
User Manual
www.aten.com
VE802 User Manual
ii
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operate d in a comme r ci al environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed an d used in accordance with
the instruction manual , ma y cau se harm ful inte rference to radio communications.
Operation of th is equipment i n a residenti al area is lik ely to c ause harmful interferenc e
in which case the user will be require d to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
CE Warning: This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
Suggestion: Shielded twist ed pai r (STP) cable s must be used with the unit to ensure
compliance with FCC & CE standards.
RoHS
This product is RoHS compliant.
SJ/T 11364-2006
The following contains information that rela tes to China.
VE802 User Manual
iii
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
User Notice
All information, documentation, and specifications contained in th is manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modi fications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage settin g was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
International http://eservice.aten.com
International 886-2-8692-6959
China 86-10-5255-0110
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
United Kingdom 44-8-4481-58923
VE802 User Manual
iv
Package Contents
VE802 Package Contents
1 VE802T/R HDMI HDBaseT-Li te Ex tender with POH
1 Power Adapter
1 IR Transmitter
1 IR Receiver*
2 Terminal Blocks
1 User Instructions
VE802T Package Contents
1 VE802T HDMI HDBaseT-Lite Transmitter with POH
1 Power Adapter
1 IR Transmitter
1 Terminal Block
1 User Instructions
VE802R Package Contents
1 VE802R HDMI HDBaseT-Lite Receiver with POH
1 IR Receiver*
1 Terminal Block
1 User Instructions
1 Power Adapter
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual tho rou ghly and follow the installatio n and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
Features may have been added to the VE802 since this manual was published.
Please visit our website to download the most up-to-date version of the manual.
Note: * The included IR receiver supports full frequency IR signals from
30kHz to 60kHz. The IR receiver cable included with the package,
however, only supports signals from 30kHz to 56 kHz.
© Copyright 2015 ATEN® International Co., Ltd.
Manual Date: 2015-05-11
ATEN and the A TEN logo are registered tr ademarks of ATEN International Co. , Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
VE802 User Manual
v
Contents
EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
VE802 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
VE802T Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
VE802R Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Chapter 1.
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Source Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Chapter 2.
Hardware Setup
Setting Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
RS-232 Channel Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Chapter 3.
Operation
LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
VE802T (Transmitter) and VE802R (Receiver). . . . . . . . . . . . . . . . . .11
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
VE802 User Manual
vi
About this Manual
This User Manual is provided to help you get the most from your system. It
covers all aspects of installation, configuration and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the VE802 system. Its purpose,
features and benefits are presented, and its front and back panel components
are described.
Chapter 2, Hardware Setup, describes the steps that are necessary to
quickly and safely set up your installation.
Chapter 3, Operation, explains the fundamental concepts involved in
operating the VE802
An Appendix, provides specifications and other technical information
regarding the VE802.
VE802 User Manual
vii
Conventions
This manual uses the following conv entions:
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start → Run means to
open the Start menu, and then select Run.
Indicates critical information.
International http://www.aten.com
North America http://www.aten-usa.com
1
Chapter 1
Introduction
Overview
The VE802 HDMI HDBaseT-Lite Extender extends an HDBaseT signal up to
70m from the HDBaseT source using one Cat 5e/6 cable. VE802 supports RS-
232 and IR signaling pass-through, allowing you to control the HDMI source
device from the remote unit (VE802R) while also granting access to the HDMI
display device from the local unit (VE802T). IR signals can also be extended
in both directions. The VE802 features Power over HDBaseT (POH) which can
send power over Cat 5e/6 cable without an additional power supply. The
VE802 is HDMI (3D, Deep Color,4kx2k) and HDCP compatible. The VE802
is perfect for a digital entertainment center or any installation that requires
superior video quality .
Chapter 1. Introduction
2
Features
HDBaseT Connectivity – extends an HDMI connection over a long
distance via one Cat 5e/6a cable
HDBaseT Anti-jamming – resists signal interferen ce during high-quali ty
video transmission using HDBaseT tech nolo gy
EDID Expert – configures optimum EDID settings for smooth power-up,
high-quality display and use of the best resolution across different screens
POH (Power over HDBaseT) – supplies power from Transmitter to
Receiver over a long distance via one Cat 5e/6a cable
A bi-directional RS-232 serial port to connect with a high-end system for
more device control
A bi-directional IR channel for IR signal cont rol; IR transmission is
processed one way at a time
Supports IR signal frequencies from 30kHz to 60kHz*
Rack- Mountable
Note: * The included IR receiver supports full frequency IR signals from
30kHz to 60kHz. The IR receiver cable included with the package,
however, only supports signals from 30kHz to 56 kHz.
VE802 User Manual
3
Requirements
Display
An HDMI display capable of the high est required resolution
Source Device
The following equipmen t is required:
A source device with an HDMI port
Cables
Cat 5e cable is required to connect the T ransmitter and Receiver units.
Cable of a lower standard will result in degrading the vid eo signal. We
strongly recommend using Cat 5e cables or above.
For better quality over lon ger distances, we suggest using 2L – 2801 (350
MHz) Low Skew Cable.
Maximum Cable Distances
Note:* 70m is the maximum cable dist ance when using a Cat 6a or above
cable.
Connection Distance
Computer to Transmitter (VE802T) 1.8 m
Transmitter (VE802T)
to Receiver (VE802R)
70 m*
Receiver (VE802R) to monitor 1.8 m
Chapter 1. Introduction
4
Components
See Chapter 3, Operation for details.
No. Component Description
1 F/W Upgrade Switch The Firmware upgrade port is r eserved for tech
support. If you would like to do a firmware
upgrade yourself, please contact your dealer.
2 IR Port Connect an IR Transmitter to the IR port on the
VE802T.
3 RS-232 Port You can connect the RS-232 main controller to the
VE802, such as the PC or Control system.
4 HDMI Input Port Connect the HDMI Input Port on the VE802T to
the HDMI Output Port on the video source device
using an HDMI cable.
5 HDBaseT Output Port The Cat 5e cables that connects the Receiver
Units, plug in here.
6 Locking Power Jack The cable from the Power adapter connects here.
VE802T Front View
56
VE802T Rear View
34
12
VE802T Top View
VE802 User Manual
5
See Chapter 3, Operation for details.
No. Component Description
1 HDBaseT Input Port The Cat 5e cables that connects to the
Transmitter Unit plugs in here.
2 Locking Power Jack The cable from the Power adapter connects here.
3 F/W Upgrade Switch The Firmware upgrade port is reserved for tech
support. If you would like to do a firmware
upgrade yourself, please contact your dealer.
4 IR Port Connect an IR Receiver to the IR port on the
VE802R.
5 RS-232 Port You can connect RS-232 serial devices/
peripherals to the VE802, such as touchscreens
and bar code scanners.
6 HDMI Output Port Connect the HDMI display to this port.
VE802R Rear View
VE802R Front View
12
3456
VE802R Top View
Chapter 1. Introduction
6
This Page Intentionally Left Blank
Chapter 2
Hardware Setup
Setting Up
Setting up the VE802 HDBaseT-Lite Extender system is simply a matter of
plugging in the cables. Make sure that all the equipment to be connected are
powered off, then refer to the installation diagram on the next page and do the
following:
1. Connect the HDMI Input Port on the VE802T to the HDMI Output Port on
your video source device using HDM I cable.
2. Connect one end of the RJ-45 cable to the HDBaseT output port on the
transmitter . Then connect the other end of the RJ-45 cable to the HDBaseT
input port on the receiver.
3. Connect the HDMI Output Port on the VE802R to the HDMI Input Port on
your video disp lay device using HDMI Cabl e.
4. Plug the power adapter into the power jack on the VE802T.
(Optional) Plug the power adapter into the Power Jack on the VE802R if
necessary.
5. (Optional) Connect you computer or contro ller system to the termi nal
block on the VE802 to serial commands
6. (Optional) Connect an IR Transmitter/Receiver to the IR port on the
VE802T/VE802R.
1. Important safety informat ion is provided on page 13. Please
review it before proceeding.
2. Make sure that the power to all devices connected to the
installation are turned off. You must unplug the power cords of
any computers that have the Keyboard Power On function.
Chapter 2. Hardware Setup
8
Installation Diagram
VE802T
1
2
3
4
5
5
6
VE802R(R)
VE802R(F)
VE802T(R)
VE802T(F)
6
VE802 User Manual
9
RS-232 Channel Transmission
You can connect RS-232 serial devices/peripherals to the VE802, such as
touchscreens and bar code scanners. The RS-232 signal transmission flow is
shown in the following example:
From a source device, the RS-232 signal is transmitted (Tx) to the VE802T
receiving (Rx) unit; the VE802R transmits (Tx) signals to the display device
(Rx).
PIN
CONFIGURATION
(Captive screw
connectors)
Tx
Rx
Gnd
Tx
Rx
Gnd
Tx
Rx
Gnd
Tx
Rx
Gnd
Serial
Device
Cat 5
Chapter 2. Hardware Setup
10
This Page Intentionally Left Blank
11
Chapter 3
Operation
LED Display
The VE802 Transmitter and Receiver units have front panel LEDs to indicate
their operating status, as shown in the tables, following:
VE802T (Transmitter) and VE802R (Receiver)
Note: *HDMI Ou t LED VE802R only.
LED Indication
Power (Green) Lights to indicate that the system is receiving power.
Link (Orange) Light is static to indicate that the connection to the Transmitter
and Receiver units are ok.
Flashes when there is a problem with the connection.
HDMI Out* Light is static HDMI display is normal with HDCP key.
Flashes when HDMI display is normal without HDCP key.
OFF when there is no HDMI Signal.
Chapter 3. Operation
12
This Page Intentionally Left Blank
13
Appendix
Safety Instructions
General
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
This product is for indoor use on ly.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operati on, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openin gs. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before clean ing. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V
phase-to-phase voltage.
To prevent damage to your installation, it is important that all devices are
properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug. Always follow you r local /national
wiring codes.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Appendix
14
If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabin et slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operatin g instructi ons.
Improper adjustment of other controls may result in damage that will
require extensive work by a qual ified technician to repair.
This product is for indoor use only.
VE802 User Manual
15
Technical Support
International
For online technical support – including troubleshooting, docum entation,
and software updates: http://eservice.aten.com
For telephone support, Telepho ne Support, page iii
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your com put er configuration, including operating syst em, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
Appendix
16
Specifications
Function VE802
Video Input Interface 1 x HDMI Type A Female (Black)
Impedance 100Ω
Max distance 1.8m
Video Output Interface 1 x HDMI Type A Female (Black)
Impedance 100Ω
Video Max. data rate 10.2Gbps (3.4G bps per lane)
Max. pixel clock 340 MHz
Compliance HDMI (3D, Deep Color, 4K)
HDCP Compatible
Consumer Electronics Control (CEC)
Max resolutions/ Distance Up to 4K2K @ 40m / 1080p @ 70 m
Audio Input 1 x HDMI Type A Female (Black)
Output 1 x HDMI Type A Female (Black)
Control RS-232 Connector 1x Terminal Block,3 pole
Baud rate and
protocol Baud Rate: 19200, Data Bits :8, Stop Bits:1, no
parity and flow control
IR 1 x Mini Stereo Jack Female (Black)
Power Connector 1 x DC Jack (Black)
Consumption VE802T:DC5V,3.6W;
VE802R:DC5V,4W
Environment Operating temp. 0-50ºC
Storage temp. -20-60°C
Humidity 0-80% RH, Non-condensing
Physical
Properties Housing Metal
Weight VE802T: 0.44 kg
VE802R: 0.46 kg
Dimensions (LxWxH) 14.49 x 12.30 x 3.00 cm
VE802 User Manual
17
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILI TY EXCE ED THE PRICE PAID
FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESUL TING FRO M THE USE OF THE PRODUCT, DISK,
OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with
respect to the contents or use of this documentation, and especially disclaims its quality,
performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or
documentation without obligation to notify any ind ividual or entity of such
revisions, or update. For further inquiries, please contact your direct vendor.