Table of Contents
- VM5404D/VM5808D User Manual
- Introduction
- Hardware Setup
- Front Panel Configuration
- Browser Operation
- Overview
- Logging In
- Main Page
- Profile List
- Profile Scheduling
- Connection Profiles
- Output Options
- System Settings
- Telnet Operation
- Configuration Menu
- 1. H – Call up the command list for help
- 2. GT – Set gateway address
- 3. IM – Set IP subnet mask
- 4. IP – Set IP address
- 5. LO – Load connections from profile
- 6. PW – Change password
- 7. RI – Read what input is connected to nn output
- 8. RO – Read what output is connected to nn input
- 9. SB – Set serial port baud rate
- 10. SS – Switch input to specified output
- 11. SV – Save the current connections into a profile
- 12. TI – Set timeout
- 13. VR – Software version information
- Configuration Menu
- RS-232 Commands
- Appendix
ATEN VM5808D User Manual
Displayed below is the user manual for VM5808D by ATEN which is a product in the Video Switches category. This manual has pages.
Related Manuals
4x4 / 8x8 DVI Matrix Switch with Scaler
VM5404D / VM5808D
User Manual
www.aten.com
VM5404D / VM5808D User Manual
ii
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installe d and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
Warning: This equipment is compliant with Class A of CISPR 32. In a
residential environment, this equipm ent may cause radio interference.
KCC Statement
유선 제품용 / A 급 기기 ( 업무용 방송 통신 기기 )
이 기기는 업무용 (A 급) 전자파적합기기로서 판매자 또는 사용자는 이
점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로
합니다 .
RoHS
This product is RoHS complian t.
VM5404D / VM5808D User Manual
iii
Safety
This product has been classified as Informatio n Technology Equipment.
SJ/T 11364-2006
The following contains information that relates to China.
VM5404D / VM5808D User Manual
iv
User Information
Online Registration
Be sure to register your product at our on line support center:
Telephone Support
For telephone support, call this num ber:
User Notice
All information, docu men tation, and specifications containe d in thi s m anual
are subject to change without prior notificatio n by the m a nufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particu lar purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the progr ams pro ve defectiv e following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PL EASE VERIFY THAT THE VOLTAGE S E TTING IS
CORRECT BEFORE USE.
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-949-428-1111
United Kingdom 44-175-3539-121
VM5404D / VM5808D User Manual
v
Package Contents
The VM5404D / VM5808D package consists of:
1 VM5404D / VM5808D DVI Matrix Switch with Scaler
1Power Cord
1 IR Remote Control
1 IR Receiver
1 Mounting Kit
1 User Instructions*
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encount er a prob lem, cont act your dealer.
Read this manual thorough ly and follow the installation and op erati on
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
*Features may have been added to the VM5404 D / VM5808D since this
manual was published. Please visit our website to download the most up-to-
date version.
© Copyright 2016 ATEN® International Co., Ltd.
Manual Date: 2016-06-29
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
VM5404D / VM5808D User Manual
vi
Contents
EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
Chapter 1.
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Source Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Display Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Source Device Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
VM5404D Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
VM5404D Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VM5808D Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
VM5808D Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2.
Hardware Setup
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 3.
Front Panel Configuration
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Front Panel Pushbuttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VM5404D / VM5808D User Manual
vii
Enter Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Port Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Input Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Output Port Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LCD Menu Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Menu Pushbutton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
IP Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
IP Address / Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Gateway. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Serial Port Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Operation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
EDID Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Output Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Security Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Save to a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Play/Stop the Profile Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Turn Video Wall Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Profile Pushbutton. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
IR Remote Control Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Change the Input source of an Output display . . . . . . . . . . . . . . . . . .34
Power on/off individual Output displays . . . . . . . . . . . . . . . . . . . . . . . 34
Power on/off all Output displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Chapter 4.
Browser Operation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Main Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Menu Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Profile List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Adding/Playing a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Importing/Exporting a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Profile List Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Play Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Profile Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Connection Profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Digital Signage Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Output Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Select Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
VM5404D / VM5808D User Manual
viii
Grid View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Click Cancel to undo all unsaved changes.Output Options . . . . . 48
Video Wall Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Video Wall Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Number of Displays / Output Order / Bezel Dimensions . . . . . . . 50
Null Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Independent Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Grouping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Display Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Video Wall Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Output Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DVI Video Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Fan Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Device Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
User Account. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Add Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Permission Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Port Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
EDID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
EDID Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Customized Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
EDID & CEA Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Customized EDID Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Telnet Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Configuration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
1. H – Call up the command list for help . . . . . . . . . . . . . . . . . . . . 75
2. GT – Set gateway address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
3. IM – Set IP subnet mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
4. IP – Set IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
5. LO – Load connections from profile . . . . . . . . . . . . . . . . . . . . . 76
6. PW – Change password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
7. RI – Read what input is connected to nn output . . . . . . . . . . . . 76
8. RO – Read what output is connected to nn input . . . . . . . . . . . 77
9. SB – Set serial port baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . 77
10. SS – Switch input to specified output . . . . . . . . . . . . . . . . . . . 77
11. SV – Save the current connections into a profile . . . . . . . . . . 77
12. TI – Set timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
13. VR – Software version information . . . . . . . . . . . . . . . . . . . . . 77
VM5404D / VM5808D User Manual
ix
Chapter 5.
RS-232 Commands
Serial Control Protocol Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
RS232 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Configuring the Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Switch Port Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
EDID Mode Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Mute Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Scaling Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Fan Speed Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Echo Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Black Screen Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Read Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Reset Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Baud Rate Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Save/Load Profile Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
OSD Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Alert Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
RS-232 Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
VM5404D / VM5808D User Manual
x
About this Manual
This User Manual is provided to help you get the most from your VM5404D /
VM5808D system. It covers all aspects of installat ion, configuration and
operation. An overview of th e information found in the manual is provided
below.
Chapter 1, Introduction, introduces you to the VM5404D / VM5808D
system. Its purpose, features and benefits are presented, and its front and back
panel components are described.
Chapter 2, Hardware Setup, describes how to set up your VM5404D /
VM5808D installation.
Chapter 3, Front Panel Conf iguration, explains the fundamental
concepts involved in operating the VM5404D / VM5808D at the local site via
the front panel LCD display using pushbuttons.
Chapter 4, Browser Operation, provides a complete description of the
VM5404D / VM5808D's Browser Graphical User Interface (GUI), and how to
use it to remotely configure and operate the VM5404D / VM5808D.
Chapter 5, RS-232 Protocol Commands, provides a complete list of the
serial control protocol commands used when utilizing the RS-232 Serial Port
so that an extra source device can be utilized in the installation.
An Appendix, provides specifications and other technical information
regarding the VM5404D / VM5808D.
VM5404D / VM5808D User Manual
xi
Conventions
This manual uses the following conv entions:
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
Bullet lists provide information, but do not involve sequential steps.
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start Run means to
open the Start menu, and then select Run.
Indicates critical information.
International http://www.aten.com
North America http://www.aten-usa.com
VM5404D / VM5808D User Manual
xii
This Page Intentionally Left Blank
1
Chapter 1
Introduction
Overview
The ATEN VanCryst VM5404D / VM5808D 4 x 4 / 8 x 8 DVI Matrix Switch
with Scaler is a versatile solution that provides an easy way to route high
definition video and audio from any of 4/8 DVI sources to any of 4/8 DVI
displays at the same time. As a Matrix Switch, each input can be independently
connected to any or all outputs, giving yo u the ultimate in flexibility and
control in any multi-disp lay audio/video installation.
The VM5404D / VM5808D features Seamless Switching, whi ch empl oys
FPGA matrix system architect ure to seamlessly switch between multiple
sources and multiple displays. With EDID Expert technology, the VM5404D /
VM5808D selects the optimum EDID settings for smooth pow er-up and the
highest quality display. It also features a high-performing scaling engine that
converts the video resolution into the display's native resolution to give you the
best image quality.
You can easily configure the VM5404D / VM5808D via the front panel LCD
display and pushbuttons, and through the use of an IR Remote Control. The
LCD provides a quick view of all port connections, and lets operators access
the unit’s built-in confi guration utility.
Furthermore, the VM5404D / VM5808D allows convenient configuration and
operation via an intuitive Graphical User Interface (GUI) using any web
browser. The web GUI provides you with advanced features which include
easy setup of custom Video Wall and Digital Signage configurations that can
be saved and recalled. Because your VM5404D / VM5808D can be controlled
over a standard TCP/IP connection, it conveniently integrates into any existing
network for easy remote access. For complete system and install integration,
serial control is standard through the VM5404D / VM5808D’s built-in RS-232
port that allows the switch to be controlled through a high-end controller or PC.
The VM5404D / VM5808D is an ideal solution for applications that require
DVI outputs from multiple sources to be conveniently deli vered to multiple
destinations, such as for stage presentations, competitions, control centers, and
system installations that require real-time reports.
VM5404D / VM5808D User Manual
2
Features
4x4 or 8x8 DVI I/O connections
Extends IR transmission via IR extension cable
Scaler – features a video scaling function to integrate a video wall
seamlessly with various output video formats
Seamless Switch™ – features close-to-zero second switching that provides
continuous video streams, real-time switching and stable signal
transmissions
Video Wall – allows you to create custom video wall layouts via intuitive
web GUI
EDID Expert™ – selects optimum EDID settings for smooth power-up
and high quality display
Multiple Control Methods – system management via front-pa nel
pushbuttons, IR, RS-232 and Ethernet (Telnet / Web GUI) connections
Video Wall – features up to 8/16 video wall profiles for custom screen
layouts via a point-n-click web GUI
Firmware Upgradeable
Rack Mountable (1U Design)
Chapter 1. Introduction
3
Requirements
The following devices are required for a complete VM5404D / VM5808D
installation:
Source Devices
Computer or A/V source device with DVI-D output connector(s)
Note: A DVI/HDMI adapter is required when connecting a HDMI source
device.
Display Devices
Display devices or receivers with an DVI input connector
Cables
1 DVI cable for each source device you will be connecting
1 DVI cable for each display device you will be connecting
1 Cat 5e cable
1 RS-232 serial cable
Note: No cables are included in this package. We strongly recommend that
you purchase high-quality cables of appropriate length since this will
affect the quality of the audio and video display. Contact your dealer to
purchase the correct cable sets.
VM5404D / VM5808D User Manual
4
Source Device Operating Systems
Supported operating systems are shown in the table below:
Browsers
Supported web browsers are shown in the table below:
OS Version
Windows 2000 and higher
Linux RedHat 6.0 and higher
SuSE 8.2 and higher
Mandriva (Mandrake) 9.0 and higher
UNIX AIX 4.3 and higher
FreeBSD 3.51 and higher
Sun Solaris 8 and higher
Novell Netware 5.0 and higher
Mac OS 9 and higher
DOS 6.2 and higher
OS Java Version Browser Version
Windows 8.1 V1.8.0_60 Chrome 45.0.2454.85 m
Firefox 40.0.3
Safari 5.1.7
Opera 31.0.1889.174
IE11 11
Windows 2012 R2
(64bit)
V1.8.0_60 (64bit) IE11 11 (64bit)
Windows 2008 R2
(64bit)
V1.8.0_60 (64bit) IE8 8
Windows 7
SP1(64bit)
V1.8.0_60 (64bit) IE10 10 (64bit)
Windows XP V1.8.0_60 IE8 8
CentOS 7.0
(64Bit)
V1.8.0_60 (64bit) Firefox 40.0.3
Ubuntu 12.04 V1.8.0_60 Chrome 45.0.2454.85
Solaris 11(64bit) V1.8.0_25 Firefox 33
Mac 10.10 V1.8.0_25 Safari 8
Chapter 1. Introduction
5
Components
VM5404D Front View
No. Component Description
1 LCD Display The LCD Display gives a quick view of all port
connections, and shows the various options for
configuring and operating the VM5404D. For full
details, see Main Screen, page 17.
2 Input Pushbuttons These pushbuttons refer to the DVI Input ports found
on the VM5404D rear panel. Press to select the Input
port. These pushbuttons may also correspond to menu
options, connection profiles (P1–P4) and so on.
Note: The INPUT (1–4) front panel pushbuttons have
built-in LEDs that light to indicate they have been
selected.
3 Output Pushbuttons These pushbuttons refer to the DVI Output ports found
on the VM5404D rear panel. Press to select the
Output port. These pushbuttons may also correspond
to connection profiles (P5–P8).
Note: The OUTPUT (1–4) front panel pushbuttons
have built-in LEDs that light to indicate they have been
selected.
4Prev / Next
Pushbuttons
These pushbuttons allow you to cycle through the
menu options on the LCD display.
5 Function Pushbuttons The function pushbuttons (MENU, PROFILE, ENTER
and CANCEL) are for navigating the LCD built-in
configuration utility. For full details, see Front Panel
Pushbuttons, page 15.
Note: The MENU and PROFILE front panel
pushbuttons have built-in LEDs that light to indicate
they have been selected.
12
3
45
VM5404D / VM5808D User Manual
6
VM5404D Rear View
No. Component Description
1 Power Socket This is a standard 3-pin AC power socket. The power
cord from an AC source plugs in here.
2 Power Switch This is a standard rocker switch that powers the unit
on and off.
3 Grounding Terminal The grounding wire attaches here. See Grounding,
page 12, for further details.
4 DVI Output Ports The cables from your DVI source devices plug into
these ports.
5 DVI Input Ports The cables from your DVI display devices plug into
these ports.
6 IR Port Connect the IR Receiver unit included with your
product via this 3.5 mm Mini Stereo Jack.
7 RS-232 Serial Port Connect a computer or high-end system controller via
this serial port.
8 Ethernet Port In order to access the VM5404D’s Browser Graphical
User Interface (GUI), the VM5404D must be
connected to your network. The cable that connects
the VM5404D to your LAN plugs in here. See Cable
Connection, page 13, for further details
38
56
1
2
47
Chapter 1. Introduction
7
VM5808D Front View
No. Component Description
1 LCD Display The LCD Display gives a quick view of all port
connections, and shows the various options for
configuring and operating the VM5808D. For full
details, see Main Screen, page 17.
2 Input Pushbuttons These pushbuttons refer to the DVI Input ports found
on the VM5808D rear panel. Press to select the Input
port. These pushbuttons may also correspond to menu
options, connection profiles (P1–P8) and so on.
Note: The INPUT (1–8) front panel pushbuttons have
built-in LEDs that light to indicate they have been
selected.
3 Output Pushbuttons These pushbuttons refer to the DVI Output ports found
on the VM5808D rear panel. Press to select the
Output port. These pushbuttons may also correspond
to connection profiles (P9–P16).
Note: The OUTPUT (1–8) front panel pushbuttons
have built-in LEDs that light to indicate they have been
selected.
4 Function Pushbuttons The function pushbuttons (MENU, PROFILE, ENTER
and CANCEL) are for navigating the LCD built-in
configuration utility. For full details, see Front Panel
Pushbuttons, page 15.
Note: The MENU and PROFILE front panel
pushbuttons have built-in LEDs that light to indicate
they have been selected.
12
3
4
VM5404D / VM5808D User Manual
8
VM5808D Rear View
No. Component Description
1 Power Socket This is a standard 3-pin AC power socket. The power
cord from an AC source plugs in here.
2 Power Switch This is a standard rocker switch that powers the unit
on and off.
3 Grounding Terminal The grounding wire attaches here. See Grounding,
page 12, for further details.
4 DVI Input Ports The cables from your DVI source devices plug into
these ports.
5 DVI Output Ports The cables from your DVI display devices plug into
these ports.
6 IR Port Connect the IR Receiver unit included with your
product via this 3.5 mm Mini Stereo Jack.
7 RS-232 Serial Port Connect a computer or high-end system controller via
this serial port.
8 Ethernet Port In order to access the VM5808D’s Browser Graphical
User Interface (GUI), the VM5808D must be
connected to your network. The cable that connects
the VM5808D to your LAN plugs in here. See Cable
Connection, page 13, for further details
38
56
1
2
47
Chapter 1. Introduction
9
IR Remote Control
Note: The VM5404D’s IR remote control only supports use of the 1~4 Input
and 1~4 Output push buttons.
No. Component Description
1 Power ON/OFF Use the ON and OFF pushbuttons to turn the Output
displays on or off – by individual port, or all ports. (see
IR Remote Control Operation, page 34)
2 Output Pushbuttons
1–8
Press Output display pushbuttons 1–8 to select the
Output display you want to configure (see IR Remote
Control Operation, page 34).
3 Input Pushbuttons
1–8
Press Input source pushbuttons 1–8 to select the
Input source you want to display on a selected output
(see IR Remote Control Operation, page 34).
1
2
3
VM5404D / VM5808D User Manual
10
This Page Intentionally Left Blank
11
Chapter 2
Hardware Setup
Rack Mounting
The VM5404D / VM5808D can be mounted in a 19” (1U) system rack. For the
most convenient front panel pushbutton configuration and operation at the
local site, mount the unit at the front of the rack, as follows:
1. Use the M3 x 8 Phillips head hex screws supplied with the Mou nti ng Kit
to screw the rack mounting brackets onto the front of the unit.
2. Position the unit in the front of the rack and align the holes in the mounting
brackets with the holes in the rack.
3. Screw the mounting brackets to the rack.
1. Important safety information regarding the placement of this
device is provided on page 101. Please review it before
proceeding.
2. Make sure that the power to all devices connected to the
installation are turned off. You must unplug the power cords of
any computers that have the Keyboard Power On function.
Phillips Head Hex
M3 x 8
VM5404D / VM5808D User Manual
12
Grounding
To prevent damage to your installation, it is important that all devices are
properly grounded.
1. Use a grounding wire to ground the VM5404D / VM5808D by connecting
one end of the wire to the grounding terminal, and the other end of the
wire to a suitable grounded object.
2. Make sure that all devices in your VM5404D / VM5808D installation are
properly grounded.
Chapter 2. Hardware Setup
13
Cable Connection
Installation of the VM5404D / VM5808D is simply a matter of connecting the
appropriate cables. Refer to the installation diagram on the following page (the
numbers in the diagram correspond to the steps below), and do the following:
1. Use a grounding wire to ground the unit by connecting one end of the wire
to the grounding terminal, and the othe r end of the wire to a suitable
grounded object.
Note: Do not omit this step. Proper grounding helps to prevent damage to
the unit from surges or static electricity.
2. Connect up to 4 (VM5404D) or 8 (VM5808D) DVI vi deo sources to the
DVI Input ports
3. Connect up to 4 (VM5404D) or 8 (VM5808D) DVI display devices to the
DVI Output ports
4. Connect the IR Receiver into the IR port.
5. (Optional) If using the Browser Operati on featu res (see Browser
Operation, page 37), plug a Cat 5e cable from the LAN into the VM5404D
/ VM5808D’s Ethernet port.
6. (Optional) If you are using the serial contro l function, use an appropriate
RS-232 serial cable to connect the computer or serial controller to the
VM5404D / VM5808D’s female RS-2 32 Serial port.
7. Plug the power cord supplied with the package into the VM5404D /
VM5808D’s 3-prong AC so cket, and then into an AC power source.
8. Power on the VM5404D / VM5808D and all devices in the instal lation.
VM5404D / VM5808D User Manual
14
Installation Diagram
5
6
1
3
2
4
7
15
Chapter 3
Front Panel Configuration
Overview
The VM5404D / VM5808D can be configured and operated locally via the
front panel LCD/pushbuttons and IR Remote Control; remotely over a standard
TCP/IP connection via graphical user interface (GUI) using a web browser; via
a remote terminal session using Telnet; or by a RS-232 serial controller.
The local front panel operation is discussed in this chapter. Web GUI
Operation is discussed in Chapter 4, and RS-232 serial control is discussed in
Chapter 5.
Front Panel Pushbuttons
The front panel features an LCD display and pushbuttons for convenient
operation locally. This allows users to perform operations such as selecting
which source shows on which display, viewing the IP settings, configuring the
serial port, setting the EDID Mode / OSD / Outp ut St atus, selecting security
settings, and loading/savi ng profiles.
Note the following front panel pushbutton functions:
Use the MENU pushbutton to access the Menu page options: IP Setting,
Serial Port Setting, Operation Mode, Security Mode, and Save to a Profile
(see LCD Menu Organization, page 21).
Use the PROFILE pushbutton to switch between the connection profiles
which have been added to the Profile List (see Profile List, page 39).
Pressing this pushbutton for longer than 3 seconds displays the Save to a
Profile page (see Save to a Profile, page 31).
Use the CANCEL pushbut ton to go back to a previous page, return to the
Main Screen, stop or exit an operation.
Use the ENTER pushbutton to select options and con firm op erations.
Use the INPUT / OUTPUT (1–8) or (1-4) pushbuttons to select the Input/
Output port. These pushbuttons may also correspond to menu options,
connection profiles, and so on.
The VM5404D provides Prev / Next pushbuttons to navigate the menus.
Use pushbuttons 7/8 (Prev/Next) to navigate the VM5808D menus.
VM5404D / VM5808D User Manual
16
Enter Password
Upon VM5404D / VM5808D startup, check the front panel LCD to view the
loading progress. If the Password screen / LCD Menu fails to load, an error
message displays. Reset the unit and try again.
If you are accessing the VM5404D / VM5808D for the first time, the Password
screen appears as soon as the LCD loading process is done. Enter the default
password 1234 to continue to the Main Screen (see Main Screen, page 17 ).
Additionally, th e Passw ord Screen appears if the VM5404D / VM5808D has
been configured to require a password for Front Panel operation (see Security
Mode, page 29).
To enter a password, do th e following:
1. In the Enter Password field, check that the cursor is at the first asterisk
(*) and flashing.
2. Use the front panel Input Port pu shbut ton s (1–8) or (1–4) to enter the 4-
digit password. After the fourth digit has been entered correctly, the Main
Screen displays.
3. Press Cancel to clear the password. The digits revert to 4 asterisks and the
cursor goes back to the first asterisk.
Note: 1. The VM5404D / VM5808D password can be any four di git
combination between 1111 to 8888 (VM5808D) or 1111 to 4444
(VM5404D). The default password is 1234.
2. If you enter an incorrect password, the cursor goes back to the
first digit and reverts to flashing. The Incorrect Password message
displays at the bottom of the screen, but clears as soon as a new
password is enter ed.
3. If Password option is Enabled (see Security Mode, page 29), the
LCD display time-out is 5 minutes by default.
Enter Password: * * * *
Incorrect Password
Chapter 3. Front Panel Configuration
17
Main Screen
The Main Screen shows the Input ports in the top row, which are tied to the
Output ports shown in sequent ial order (1 –8) or (1 –4) at the bott om row.
The front panel pushbutton label (1–8) or (1–4) corresponds to the Input
ports and Output ports on the unit’s rear panel.
Use the Menu pushbutton to view the LCD Menu (see LCD Menu
Organization, page 21).
Use the Profile pushbutton to switch between profile connections (see
Profile List, page 39).
Port Switching
From the Main Screen, users can configure the Input-to-Output port
connections to associate an Input so urce device to an Output display.
Input Port Selection
Use the Input Port pushbuttons to select the Input port you want to configure.
To select which input source displays on each output port, do the following:
1. Press any Input port pushbutton (1–8) or (1-4). The Output port LED(s)
tied to the said Input port will begin to flash. Available output port LED(s)
will light up (steady).
In the example below , pressing Input port 1 shows it is tied to Output ports
1 and 2.
(Continues on next page.)
INPUT 1 2 5 5 1 1 3 4
OUTPUT 1 2 3 4 5 6 7 8
P1
INPUT 1 2 5 5 1 1 3 4
OUTPUT 1 2 3 4 5 6 7 8
VM5404D / VM5808D User Manual
18
(Continued from previous page.)
2. To disconnect an Output port from an Inp ut port, press the corresponding
Output port pushbutton.
In the example below, Output port 2 has been disconnected from Input port
1.
3. To switch to another Input port, press any Input port pushbutton. The
Output port LED(s) tied to the said Input port will flash.
In the example below, pressing Input port 2 shows it is tied to Output ports
3 and 4.
4. To connect Output port 2 to Input port 2 in the example above, then press
the Output port 2 pushbutton. The Output port 2 LED will also begin to
flash (0.5 sec on, 0.2 sec off). This indicates that Input port 2 is now
connected to Output ports 2, 3 and 4.
Once the signal from the selected Input port is successfully tied to the Output
port, the LEDs turn off and the LCD information is updated.
Note: 1. Pressing an Input port a second time deselects it.
2. Input ports that are not configured or tied to any output port do not in
the LCD screen.
3. Pressing the Cancel pushbutton once stops the Input Port Selection
operation and the LCD displays the active setting. Pressing the
Cancel pushbutton again turns all LEDs off.
4. Afte r 10 seconds of inactivity, all the LEDs turn off.
Chapter 3. Front Panel Configuration
19
Output Port Selection
Use the Output Port pushbuttons to select the Output port you want to
configure.
To select which output display corresponds to each input source device, do the
following:
1. Press any Output port pushbutton (1–8) or (1 –4).
In the example below, Output port 1 pushbutton has been pressed.
Available Input ports light up. Because no Input LEDs are flashing, no
ports have already been assigned to Output port 1.
2. If an Output port pushbutton is pressed a second time, it is deselected and
the LED turns off.
3. To connect the selected Output port(s) to an Input port, press the Input port
pushbutton. to which you want the Output port(s) tied. The newly selected
Input port LED flashes (0.5 sec on, 0.2 sec off), and the LCD information
is updated.
In the example below, pressing Input port 2 ties it to Output ports 2, 3 and
4.
INPUT 1 2 5 5 1 1 3 4
OUTPUT 1 2 3 4 5 6 7 8
VM5404D / VM5808D User Manual
20
4. To switch Output ports 2, 3 and 4 to another Inp ut po rt (and disconnect it
from Input port 2), press another Input port pushbutton to which you want
them tied.
In the example below, Input port 3 has been pressed and is now connected
to Output ports 2, 3 and 4.
Note: 1. Pressing an Output port a second time deselects it.
2. Pressing the Cancel pushbutton once stops the Output Port Selection
operation, and the LCD displays the active setting. Pressing the
Cancel pushbutton again turns all LEDs off.
3. Afte r 10 seconds of inactivity, all the LEDs turn off.
Chapter 3. Front Panel Configuration
21
LCD Menu Organization
The VM5404D / VM5808D has a built-in configuration utility via the fron t
panel LCD, whic h can be controlled by pressing the MENU and front panel
Input pushbuttons (1–8). User can cycle through the me nu options, starting
from IP Setting page, in the order shown in the table below:
Note: The highlighted values are the default settings of the VM540 4D /
VM5808D.
Menu Page Sub-Menu Page(s)
IP Setting IP Address
Subnet Mask
Gateway
Serial Port Setting Baud Rate 9600 / 19200 / 38400 / 115200
Operation Mode EDID Default / Port1 / Remix / Customized
OSD On / NA
Output Status Video On / NA
Output
Resolution
01-04 (VM5404H);
01-08 (VM5808H)
Security Mode Mode None
Password Enable
Lock Screen
Change Password Old Password New Password
Save to a Profile Save to a Profile No. 01–08 (VM5404D); 01-16 (VM5808D)
Play/Stop the Profile Schedule
Turn Video Wall Off
VM5404D / VM5808D User Manual
22
Menu Pushbutton
Press the MENU pushbutton to switch between the Main Screen and LCD
Menu page. When the Menu is active, the MENU pushbutton’s built-in LED
lights up:
From the Menu page:
Press 1 to go to the IP Setting page (see IP Setting, page 22)
Press 2 to go to the Serial Port Setting page (see Seri al Port Setti ng,
page 24)
Press 8/Next to go to the nex t page(s) for the su b-menu pages
Press Menu or Cancel to return to the Main Screen
IP Setting
The IP Setting page displays the VM54 04D / VM5808D’s IP configuration.
The values in the LCD Menu are read-only and can be edited via the Browser
GUI (OSD, page 74).
IP Address / Subnet Mask
To view the VM5404D / VM5808D’s IP address and Subnet Mask, do the
following:
1. From the Menu page, press 1 to see the IP Setting submenu. The IP
address and Subnet Mask are then shown.
Note: The VM5404D / VM5808D default IP address is 192.168.0.60. The
default Subnet Mask is 255.255.255.0
2. Press 8/Next to go to the next page.
3. Press Menu to return to the Menu page.
4. Press Cancel to return to the previous page without saving.
1: IP Setting
2: Serial Port Setting 8: Next
IP Address: 192.168.0.60
Subnet Mask: 255.255.255.0 8: Next
Chapter 3. Front Panel Configuration
23
Gateway
To view the VM5404D / VM5808D’s gateway address, do th e following:
1. From the Menu page, press 1 to see the IP Setting submenu, then press 8 to
get to the next page. The gateway address displays.
Note: The default Gateway is 192.168.0.1.
2. Press 7/Prev to go to the previous page.
3. Press Menu to return to the Menu page.
4. Press Cancel to return to the previous page without sav ing.
Gateway: 192.168.0.1
7: Back
VM5404D / VM5808D User Manual
24
Serial Port Setting
To configure the VM5404D / VM5808D’s baud rate for its serial port
connection, select Serial Port Setting from the Menu pag e.
Baud Rate
To set the VM5404D / VM5808D’s baud rate, do the following:
1. Select Baud Rate Setting from the Serial Port Setting submenu by
pressing 1:
2. Press pushbuttons 1–4 to make your selection.
Baud Rate options are:
1: 9600
2: 19200
3: 38400
4: 115200
Note: The default baud rate is 19200.
3. Press Menu to return to the Menu page.
4. Press Cancel to return to the previous step without saving.
1: IP Setting
2: Serial Port Setting 8: Next
1: Baud Rate Setting
1: 9600 3: 38400
2: 19200 (In use) 4: 115200
Chapter 3. Front Panel Configuration
25
Operation Mode
The EDID Mode, OSD and Output Status features can be configured from the
Operation Mode page.
EDID (Extended Display Identificati on Data) is used to have the
VM5404D / VM5808D automatically apply a preset video
configuration or EDID Mode, which utilizes the best resolution across
different monitors
The OSD, when enabled for a port, lets an attached display/monitor
show real-time port switching information
The Output Status shows whether the video/audio of an Output port is
turned on or off and allows viewing and setting of the Output
Resolution
To configure the VM5404D / VM5808D’s operatio n mode settings from the
Main Screen, use the Menu pushbutton to access the Menu page, press 8/Next
to navigate to the next page, then press pushbutton 1 to access the Operation
Mode page.
EDID Mode
To configure the EDID Mode, do the following:
1. From the Operation Mode page, press pushbutton 1:
(Continues on next page.)
1: Operation Mode
2: Security Mode 8: Next
7: Back
1: EDID Mode
8: Next
VM5404D / VM5808D User Manual
26
2. Press pushbuttons 1–4 to make your selection.
EDID Mode options are:
3. Press Menu to return to the Menu page.
4. Press Cancel to return to the previous step without saving.
OSD
The On-Screen Display or OSD feature enables real-time text updates to
appear on the display device’s screen for any configuration changes made to
the Output port via the VM5404D / VM5808D’s front panel, IR remote control
or Browser GUI.
To configure the OSD setting for each output port, do the following:
1. From the Operation Mode page, press 8 or Next to go to the next page,
then press pushbutton 1:
2. From the Output Status page, press pushbutton 1:
EDID Option Description
1: Port1 The EDID from port1 is passed to all video sources.
2: Default The default EDID is passed to all video sources.
3: Remix Uses the EDID of each connected display according to its
connection when the VM5404D / VM5808D is first powered on,
or immediately after pressing 3 to select the Remix option.
4: Customized Automatically retrieves and saves the EDID settings of a
connected monitor/display device to an input source port. This
can be configured using the Browser GUI. See Customized
EDID Settings, page 69.
1: Port 1 3: Remix
2: Default (In use) 4: Customized
1: OSD 7: Back
2: Output Status
1: Video
Chapter 3. Front Panel Configuration
27
3. Press pushbuttons (1–8) or (1–4) to enable (ON) or disable (NA) the OSD
feature for the output port.
Note: The default OSD setting is On.
4. Press Menu to return to the Menu page.
5. Press Cancel to return to the previous step without saving.
Output Status
To configure the Output Status settings for each output port, do the following:
1. From the Operation Mode page, press 8 or Next to go to the next page,
then press pushbutton 2:
2. From the Output Status page, press 1 to select Video.
3. Press pushbuttons (1–8) or (1–4) to enable (ON) or disable (NA) the
video/audio of the output port .
Note: The default Output Status setting is On.
4. Press Menu to return to the Menu page.
5. Press Cancel to return to the previous step without saving.
OUTPUT 1 2 3 4 5 6 7 8
ON ON ON NA ON NA ON NA
1: OSD 7: Back
2: Output Status
1: Video
2: Output Resolution
OUTPUT 1 2 3 4 5 6 7 8
ON ON ON NA ON NA ON NA
VM5404D / VM5808D User Manual
28
To configure the Output Resolution settings for each output port, do the
following:
1. From the Operation Mode page, press 8 or Next to go to the next page,
then press pushbutton 2:
2. From the Output Status page, press 2 to select Output Resolution.
3. Press pushbuttons (1–8) or (1–4) to select an output port whose resolution
will be changed.
4. Available options include: Native Resolu tio n, 1024x768@60Hz,
1280x720@60Hz, 1280x10 24@60Hz, 1400x1050@60H z,
1600x1200@60Hz, 1920x1080@60Hz, 19 20x1200@60Hz,
1280x720@50Hz, 1920x1080@50Hz, 1280x800@60Hz, 720x576@50Hz
and 1600x900@60Hz.
5. Press Menu to return to the Menu page.
6. Press Cancel to return to the previous step without saving.
1: OSD 7: Back
2: Output Status
1: Video
2: Output Resolution
OUTPUT 1 2 3 4 5 6 7 8
Chapter 3. Front Panel Configuration
29
Security Mode
The Security Mode page allows users to manage the VM5404D / VM5808D’s
security-related settings. Three security modes are available: None, Password
Enable and Lock Screen. The VM5404D / VM5808D’s password can also be
changed here.
To configure the VM5404D / VM5808D’s secu rity settings from the Main
Screen, use the Menu pushbutton to access the Menu page, press 8 or Next to
navigate to the next page, then press pushbutton 2 to access the Security Mode
page.
Mode
1. To change the VM5404D / VM5808D’s security mode, press pushbutton 1
in Security Mode.
2. In the Mode menu, to disable security settings, press pushbutton 1. The
menu will then return to Security Mode. To require a password after the
LCD display times out or is powered off/on, press pushbutton 2. The menu
will then return to the home screen.
Note: If Password is Enabled, the LCD display’s default time-out is 5 minutes.
The VM5404D / VM5808D’s default password is 1234.
3. To enable a lock screen, press 8 or Next to navigate to the next page, then
press pushbutton 1. The menu will then return to the home screen . When
Lock Screen is enabled, pressing any pushbutton from the hom e screen
will trigger the following message: Please press “Menu” to start.
1: Operation Mode
2: Security Mode 8: Next
7: Back
1. Mode: None
2. Change Password
1. None (In Use)
2. Password Enable 8: Next
1. Lock Screen 7: Back
VM5404D / VM5808D User Manual
30
4. Press Menu to return to the Menu page.
5. Press Cancel to return to the previous step without saving.
Change Password
1. To change the password for accessing the unit, press pushbutton 2.
2. In the Old Password field, the cursor flashes at the first digit. Enter the old
password (see Enter Password, page 16). If the old password is ente red
correctly, you can proceed to the next step.
Note: If you entered an incorrect password, an error message appears and the
cursor goes back to the first digit (flashing). The Incorrect Password
message clears as soon as a new digit is entered.
3. In the New Password field, the cursor flashes at the first dig it. Enter the
new password using the front panel number pushbuttons VM5808H:
(1111–8888) or VM5404H: (1111–4444).
4. Re-enter the new password in the followi ng screen. The new password is
applied by the VM5404D / VM5808D im mediately.
If the password you entered does not match the one entered in the previous
screen, an error message appears. Enter th e ne w password correctly.
5. Press Menu to return to the Menu page.
6. Press Cancel to return to the previous step without saving.
1. Mode: None
2. Change Password
Old Password: * * * *
Incorrect Password
New Password: * * * *
Re-enter New Password: * * * *
Chapter 3. Front Panel Configuration
31
Save to a Profile
The switch allows users to store up to 8 (VM5404D) or 16 (VM5808D )
(numbered P1–P16) different connection profiles that can be saved and
recalled later.
The active Input-to-Output port connections on the LCD Main Screen is the
configuration saved to a profile. When a user loads a profile, the change is
immediate and the profile number is shown on the lower right corner of the
LCD screen.
To save a profile once the desired port connections are set, do the follow ing :
1. Press the Menu pushbutton to access the Menu page, then 8/Next to
navigate to the next pages. Press pushbutton 1 to open the select Save to a
Profile page.
2. On the page that opens, you are asked to give the profile a number . Use the
front panel number pushbuttons to select a profile number into which you
want to save the configuration.
VM5404D: Options are P1–P8 (when saving a profile via the LCD),
where:
Input port pushbuttons 1–4 correspond to Profile P1 to P4
Output port pushbuttons 1–4 correspond to Profile P5 to P8
VM5808D: Options are P1–P16 (when saving a profile via the LCD),
where:
Input port pushbuttons 1–8 correspond to Profile P1 to P8
Output port pushbuttons 1–8 correspond to Profile P9 to P16
3. Press Enter to store the configuration – the LCD shows Profile Saved.
4. Press Menu to return to the Menu page,
5. Press Cancel to return to the previous step without saving.
Note: Access the Save to a Profile page quickly by pressing the Profile
pushbutton for longer than 3 seconds.
1: Save to a Prole
2: Play/Stop the Prole Schedule
7: Back
Save to a Prole No. 1
In 1-8=P1-P8;Out 1-8=P9-16.
VM5404D / VM5808D User Manual
32
Play/Stop the Profile Schedule
Inputting port pushbutton 2 will Play or Stop the active Profile Schedule.
1: Save to a Prole
2: Play/Stop the Prole Schedule
7: Back
Chapter 3. Front Panel Configuration
33
Profile Pushbutton
The PROFILE pushbutton lets users conveniently switch between connection
profiles that have been saved or added to the Profile List (see Profile List,
page 39).
When a Profile is in use, its profile number (P1–P16) is shown on the lower
right corner of the LCD display.
The Profile pushbutton functi o ns as follows:
After pressing the Profile pushbutton, available profile numbers will light
up. The active profile number will flash. use the Input/Output pushbuttons
to switch to a specific profile (P1 to P16) or (P1 to P8). Note that:
Input ports 1–8 or 1-4 correspond to Profile P1 to P8 or P1 to P4
Output ports 1–8 or 1-4 correspond to Profile P9 to P16 or P5 to P8
(where Output Port 1=Profile 9, Output Port 2=Profile 10... Ou tput
Port 8=Profile 16)
The selected pushbutton’s light flashes, and the VM5404D / VM5808D
immediately applies the port connections configured in the selected
profile. If the light changes to a steady state, it means the profile is valid.
After pressing the Profile pushbutton, pressing it again will change to next
profile in Profile Scheduling (see page 44), not the profile list. This feature
is only available while a schedule is playing.
Press the Cancel pushbutton to exit
Note: If there are no profiles configured on the VM5404D / VM5808D device,
an error message “No Available Profile” is displayed when the Profile
pushbutton is pressed.
A Profile’s port connections can be edited using the front panel pushbuttons
(see Port Switching, page 17) or from the Connections page of the Browser
GUI (see Connection Profiles, page 46). Additionally, the Profile List can be
configured via the Profile page of the Browser GUI (see Profile List, page 39).
INPUT 1 2 5 5 1 1 3 4
OUTPUT 1 2 3 4 5 6 7 8 P1
VM5404D / VM5808D User Manual
34
IR Remote Control Operation
The IR remote control (IR Remote Control, page 9) included with the
VM5404D / VM5808D can be used to:
change the Input source of any Output display
power on/off individual Output displays; or
power on/off all Output displays simultaneously
Before using the remote control, a user must first plug the IR External Receiver
into the rear panel of the VM5404D / VM5808D and place the receiver where
the IR signal can be reached (see IR Port, pag e 8).
Change the Input source of an Output display
To change the Input source of an Output display, using the remote control, do
the following:
1. Press the Output port number (1–8) or (1-4) you want to change.
2. Within 2 seconds press the Input port number (1–8) or (1-4) you want the
Output port to display.*
3. Repeat steps 1-2 to change additional ports.
*For the change to occur the Input number mu st be pressed with in 2
seconds of pressing the Output number.
Power on/off individual Output displays
To power on/off individual Output displays, using the remote control, do the
following:
1. Press the Output port num ber (1–8) or (1-4) you want to power on/off.
2. Within 2 seconds press the ON or OFF pushbutt on.*
3. Repeat steps 1-2 to change the power status back on/off.
*If the ON or OFF pushbutton is pressed after 2 seconds of pressing the
Output port number, all the displays are powered on or off instead of just
the intended Output port.
Chapter 3. Front Panel Configuration
35
Power on/off all Output displays
To power on/off all Output displays simultaneously, with the remote control,
do the following:
1. Press the ON or OFF pushbutton.*
2. Repeat step 1 to simultaneously change back the power status of all Output
ports, to on or off, respectively.
*The ON or OFF pushbuttons bring all displays to the same power status,
regardless of the individual power statuses.
VM5404D / VM5808D User Manual
36
This Page Intentionally Left Blank
37
Chapter 4
Browser Operation
Overview
The VM5404D / VM5808D can be configured over a st andard TCP/IP
connection via its built-in Graphical User Interface (GUI). Because it can be
accessed from anywhere over a network or the Internet, operators can easily
log in via web browser. Security is ensured by password protection and user-
configurable time-out. The VM5404D / VM5808D supports three levels of
remote users with various privileges, and up to 32 users can log into the GUI
at one time. For full details, see the sections that follow.
Logging In
To access the GUI, type the VM5404D / VM5808D’s IP address into the
address bar of any browser. If a Security Alert dialog box appears, accept the
certificate – it can be trusted. The login screen appears:
The default IP address is http://192.168.0.60
The default Username and Password are: administrator / password
Enter the username and password, then click Login.
The same user can not be logged in simultaneously.
Use the drop-down menu to select the GUI language
English, French, German, Italian, Japanese, Korean, Portuguese,
Russian, Spanish, Simplified Chinese and Traditional Chinese
Note: The username supports lower case letters only.
VM5404D / VM5808D User Manual
38
Main Page
The Main Page op ens to the Profile List. This is where you configure the input
to output connections by creating profiles. The page is divided into three parts:
the Menu Bar, Profile List, and Profile Schedul ing.
Menu Bar
The Menu Bar consists of the Settings icon and Logout button.
Click Settings to enter the System Settings (see page 57).
Click the Logout button to log out of the GUI.
Chapter 4. Browser Operation
39
Profile List
The Profile List lets you con figure the input to output port connections by
creating profiles to use. You can store up to 8 (VM5404D) or 16 (VM5808D)
differently configured profiles that can be saved an d played by two methods:
locally via the unit’s front panel pushbuttons and via the web GUI.
Adding/Playing a Profile
To configure a connection pro fil e:
1. From the Profile List, click a [Profile].
2. Select the profile type:
Digital Signage: Select this option fo r video that is displayed
independently on sep arate monitors (page 46).
V ideo W all: Select this option for monitors that are displayed together -
tiled or as a large screen (page 49).
3. Configure the input to output connections for a Digital Signage (page 46)
or Video Wall (page 49) profile.
VM5404D / VM5808D User Manual
40
4. New profiles appear in the Profile List, as shown here:
5. Select the profile and click Apply.
6. The profile appears in the large Play window and the connections start:
Note: More information about Profile List options are provided on the next
page.
Chapter 4. Browser Operation
41
Importing/Exporting a Profile
To export the VM5404D / VM5808 D’s connection profiles, do the followin g:
1. Click Export Profiles. A configuration file will then begin downloadin g.
To import connection profiles to the VM5404D / VM5808D, do the following:
1. Click Import Profiles.
2. Browse to the configuration file, select it and click Open.
Note: Importing a connection profile database will overwrite the current
profiles.
VM5404D / VM5808D User Manual
42
Profile List Options
Clicking a Profile or the Play window opens a pop-up menu with optio ns.
Profile
Play Window
Option Description
Apply Click Apply to put the profile in the Play window. This allows you to
start the profile connections.
Edit Click Edit to configure the profile's input to output connections.
Option Description
On Sequence On Sequence will appear when a profile schedule is playing (see
page 44).
<Click < to go back to the previous profile in the sequence, when
Profile Scheduling is in use. Only available with On Sequence.
>Click > to advance to the next profile in the sequence, when Profile
Scheduling is in use. Only available with On Sequence.
Positioning Click Positioning to open a window that allows you to adjust the
image position on each display. For Video Wall profiles, you can
also set the Bezel Dimension, which is the frame thickness between
each display.
Remove Removes the profile from the Play window.
Chapter 4. Browser Operation
43
Other
Edit Click Edit to configure the profile's input to output connections.
Option Description
Show OSD Check Show OSD to show text updates that appear on the display
when configuration or port changes are made.
Mute All Check Mute All to mute the audio for all ports.
Blank All Check Blank All to turn off the video to all displays.
Option Description
VM5404D / VM5808D User Manual
44
Profile Scheduling
Profile Scheduling is located below the Profile List. Scheduling allows you to
queue and play connection profiles in sequence for a specific amount of time.
Option Description
Click to edit profile schedule.
Click to play profile schedule.
Click to stop profile schedule.
Click to change to next or previous profile when a profile schedule is
playing.
Chapter 4. Browser Operation
45
After selecting Edit, you will be presented with the following options.
Option Description
Click to add profiles to the schedule in the order to be played, left to
right, then set the amount of time each profile plays.
Click a profile for a pop-up menu to appear:
Select Startup to use the profile as the starting point for the
schedule.
Click Replace to replace the selected profile with another profile.
Click Remove to delete the profile from the schedule.
Use < > to change the profile’s position in the schedule.
Use the drop-down menu to select the duration (Hours, Minutes, or
Seconds) and enter the amount of time for the profile to play. After
the time expires, the schedule switches to the next profile.
Use Repeat to stop switching between schedules and stay on the
currently selected profile. If Repeat isn’t used, the schedule will loop
back to the first profile. If Repeat is used, a specific number of
hours, minutes and seconds cannot be set and later profiles will not
be played.
Save Click Save to save the schedule as it appears. After saving, the
Profile Scheduling window will close.
When a Profile Schedule is playing the On Sequence box will
appear in the Play window.
Cancel Click Cancel to discard changes and return to the Profile Schedule
page.
VM5404D / VM5808D User Manual
46
Connection Profiles
There are two types of profiles: Digital Signage and Video Wall. Digital
Signage profiles are for displays where video is viewed on separate
monitors.Video Wal l profiles are for displays that are tiled together, where
multiple monitors form one large screen – in various arrangements.
Digital Signage Profile
Each icon represents an output port and the connected display. The large
number is the Input port selected for the display. The small number (upper-left
corner) is the Output port for the display. Click the icons to select options.
Select icons to choose the Video Input from the Select Source menu.
Click the PEN icon or name to edit the profile name.
Click Select All to select all outputs.
Click Unselect All to unselect all outputs.
Click Save to save the profile or Save as to save as a different profile
number.
Click Grid View to use an alternate method for configuring connection
profiles (see page 48).
Chapter 4. Browser Operation
47
Output Icon
Select Source
Option Description
Output Icon Click an Output icon(s) to highlight it in green and use the Select
Source menu to set the video options (see Select Source below).
The large number is the Video Input port selected for the display.
The small number (upper-left corner) is the Output port of the
display.
Mute / Video Click the speaker icon to mute the audio on/off.
Click the video icon to turn the video off/on.
Option Description
Select Source The Select Source menu appears when you click an Output icon.
Output Displays the Outputs that are selected for the configuration change.
Video Input Use the drop-down menu to select the Video Input.
Click Save or Save as to save the changes.
Radio Button Fit Width of Output(s): fits the video to the width of the display.
Fit Height of Output(s): fits the video to the height of the display.
Scale to Whole Output(s): fits the video on the entire display.
VM5404D / VM5808D User Manual
48
Grid View
The Grid View allows you to select the Input to Output connections using a
simple grid.
Select a box to coordinate Input Ports to Output Ports. By default,
ports will be aligned so that i01 will correspond to o01, etc.
Uncheck a box to disable the video for that Output Port. The column
will no longer contain a yellow box.
Check an Input Port radio button to align all Output Ports to that Input
Port.
Click Test to play current profile witho ut saving.
Click Save & Apply to save a profile and begin playing it.
Click Save to save the profile.
Click Save as to save the profile as a different profile number.
Click Cancel to undo all unsaved changes.Output Options
For instructions on the Output Options, see Outp ut Options, page 55.
Chapter 4. Browser Operation
49
Video Wall Profile
Each blank icon represents an Output port and the connected display. Use the
icons to create Independent and Grouped Outpu ts. Independent Outputs will
display video on a single monitor. Grouped Outputs will display video across
multiple monitors as one large screen.
Video Wall Options
Click an icon to choose its Output and Video Input from the Display
Preference menu (see page 52).
Click multiple icons to G rou p Outputs (see Grouping, page 52) and
choose the Video Input from the Display Preference menu.
Use + next to Di splay Layout _1 to create additi onal layouts under
the same profile.
Click the PEN icon or name to edit the profile name.
Click Select All to select all outputs.
Click Unselect All to unselect all outputs.
Click Test to play current profile without saving.
Click Save & Apply to save the profile and put it in the Play win dow
(see page 42).
Click Save to save the profile.
Click Save as to save the profile as a different profile number.
Click Cancel to discard changes and return to the Profile List.
VM5404D / VM5808D User Manual
50
Number of Displays / Output Order / Bezel Dimensions
Option Description
Number of
Displays
Use the Horizontal and Vertical drop-down menu to select the
number of displays that make up the video wall (a maximum of 64
are supported). Match this to the physical layout of the displays.
Click Apply to set the layout.
Output Order Automatically assign output ports by selecting one of the following
options: Left to right (top to bottom), right to left (top to bottom), top
to bottom (left to right) or top to bottom (right to left).
Bezel
Dimension
Use the four boxes to increase/decrease the frame size for each
active display.
Monitor
Lock / Unlock
Click the monitor icon to Lock the (4) bezel settings, so that when
one size is changed they all change.
Click the monitor icon to Unlock the (4) bezel settings, so that each
size can be set independently.
Chapter 4. Browser Operation
51
Null Input
Option Description
Null Input Icon Click Null Input icons to highlight icons in green and use the Display
Preferences menu to set the video options (see Display
Preferences, page 53).
Select a single icon to set the Output and Video Input for an
independent display (see Independent Output, page 52).
Select multiple icons and set the Video Input to group displays as
one screen (see Grouping, page 52). You must first set the Output
port for each icon.
Drop-down Menu Use the drop-down menu to select the Output port.
VM5404D / VM5808D User Manual
52
Independent Output
Grouping
Option Description
Independent
Output
Independent Outputs are displays that have their own Video Input
and Output selected. Independent Outputs:
Display their own video
Icons have their own color and Video Input
Select an Independent Output and use the Display Preferences
(page 53) menu select the Video Input.
Drop-down
Menu
Use the drop-down menu to select the Output port.
Mute / Video Click the speaker icon to mute the audio on/off.
Click the video icon to turn the video off/on.
Option Description
Grouping Click multiple icons to Group Outputs (highlighted in green) and
click to group the displays into one screen*. Use the Display
Preferences menu to select the Video Input for the group - each
Output icon in the Group will appear with the same Video Input
number and icon color (see Group, page 53).
Note: Before grouping you must set the Output port for each icon.
Ungroup Select a group and click to ungroup the displays.
Chapter 4. Browser Operation
53
Group
Display Preferences
Option Description
Group A Group (of Outputs) shares the same Video Input and displays
the video together as one large screen. A Group of Outputs:
Displays video across multiple monitors to form one screen
Icons have the same color and Video Input number.
Select a Group and use the Display Preferences menu to select
the Video Input.
To group outputs see Grouping, page 52.
Mute / Video Click the speaker icon to mute the audio on/off.
Click the video icon to turn the video off/on.
Option Description
Display
Preferences
Click Output icons for the Display Preferences menu to appear– to
select the Output and/or Video Input port.
Output Use the drop-down menu to select the Output port (Independent
and single Blank icons only).
If you select multiple displays the output ports selected will appear
here. You can use the output icon’s drop-down menu to change the
output port for the display.
VM5404D / VM5808D User Manual
54
Video Wall Example
The example below show s a video wall with 4 displays.
Each Group and Independent Output has a unique color.
This video wall has 1 Group and 2 Independent displays.
The Group will show Video Input 01 across both displays as one large
screen.
The Independent displays will show the video from their own Video
Input – 03 and 04.
Add Display Layouts to create separate video walls (see Video Wall
Options, page 49).
Video Input Use the drop-down menu to select the Video Input port.
Radio Button Fit Width of Output(s): fits the video to the width of the display.
Fit Height of Output(s): fits the video to the height of the display.
Scale to Whole Output(s): fits the video on the entire display.
Option Description
Chapter 4. Browser Operation
55
Output Options
The Output Options page is used to config ure DVI Video options.
DVI Video Options
DVI Video Options allow you to set Seamless Switch options which determine
how a display performs when the input port is changed.
The Transition, Period and Scale Resolution apply only when Seamless
Switching is on.
Seamless Switch: Turning Seamless Switch on removes the video
distortion and delay seen when an input port is switched.
Use the drop-down menu to apply to all ports, or the ON/OFF
button to enable/disable Seamless Switching per port.
Transition: Allows you to fade the video display when the input port is
changed. Use the period option to set the fade speed.
Use the drop-down menu to apply to all ports, or ON/OFF button
to enable/disable Transitions per port.
Period: Sets the fade speed for the Transition option.
Use the drop-down menu to apply an option (Slow, Normal, or
Fast) to all ports, or lower drop-down menus to apply options per
port.
Scale Resolution: Forces the port to scale the video displayed to th e
selected resolution. Options are: 720x576 @50HZ, 1024x768@60HZ,
VM5404D / VM5808D User Manual
56
1280x720@50HZ, 1280x720@60HZ, 1280x800@60 HZ,
1280x1024@60HZ, 1400x1050@60Hz, 1600x900@60HZ,
1600x1200@60HZ, 1920x1200@60HZ, 1920x1080@50HZ,
1920x1080@60HZ.
Use the top drop-down menu to apply an option to all ports, or
lower drop-down menus to apply opt ion s per port.
Click Test to play current profile witho ut saving.
Click Save to save the profile or Save as to save as a different profile
number.
Click Save & Apply to save the profile and put it in the Play win dow
(see page 42).
Click Cancel to discard changes and return to the Profile List.
Chapter 4. Browser Operation
57
System Settings
Click the Settings link from the Main page for the System Settings to open on
the General page:
The General page allows you to edit Baud, Language and Fan settings
and view device information.
The User Account page allows you to add and edit user accounts.
The Port Name page allows you to name each input and output port.
The Network page allows configuration of the network settings.
The EDID page is used to set the EDID modes.
The Maintenance page is for upgrading the device’s firmware.
The HDCP page is lets users view and set HDCP key settings.
The OSD page allows users to control port OSD settin gs.
Click Back to Profile List to return to the Main page.
VM5404D / VM5808D User Manual
58
General
The General page has three sections: Fan Status, Device Info and Other.
Fan Status
This section displays the VM5404D / VM58 08D’s two fans’ statuses.
The VM5404D / VM5808D also includes a drop-down menu which
allows for manual selection of fan speed.
Note: If the fans have stopped working or are switched off, they will
appear as follows.
Device Info
This section lists the device’s type, Model Name, Firmware Version
and port statuses.
Other
Use the Language drop-down menu to select a preferred user interface
language.
Options include: English, French, German, Italian, Japanese,
Korean, Portuguese, Russian, Spanish, Simplified Chinese and
Traditional Chinese.
Use the Baud Rate drop-down menu to select a serial port setting.
Options include: 9600, 19200, 3840 0 and 115200.
Chapter 4. Browser Operation
59
Options include: English, French, German, Italian, Japanese,
Korean, Portuguese, Russian, Spanish, Simplified Chinese and
Traditional Chinese.
Use the Baud Rate drop-down menu to select a serial port setting.
Options include: 9600, 19200, 38400 and 115200.
VM5404D / VM5808D User Manual
60
User Account
The User Account page lets you add, edit, or delete users and change the
password for accessing the VM5404D / VM5808D’s GUI.
Note: This is an Administrator only function.
Add account – Click the Add account button to add another user to the
list. The VM5404D / VM5808 D supports up to 32 users at one time
(see page 61 for more details).
Edit – Click the Edit button to change user information. This option
allows an Administrator to edit individual accounts.
Edit – Rename the user account, set the password, add a
description, and set the user’s permission level (see page 61 for
more details).
Delete – Removes the user account.
The default username and password are: administrator/password.
Chapter 4. Browser Operation
61
Add Account
Use the Add Account / Edit buttons to create a user account, set the user’s
password, add a description, and set the user’s permission level (see
Permission Level, page 62) when accessing the VM5404D / VM5808D’s GUI.
Fill in a username or edit an existing one.
Enter a password and re-type the password to confirm.
Note: Usernames and passwords accept multi-lingual characters, and must
be 5–16 alphanumeric characters (excluding :;=[]+=/?\|). Passwords
are case sensitive. Usernames only support lower case letters.
Add or edit the description for the user.
Select the permission level that you wa nt to grant the user (see
Permission Level, page 62).
Click Create User to save the data.
Click Cancel to discard the changes and exit.
If a user is logged into the VM5404D / VM5808D’s GUI, their user
settings cannot be edited, and the fields in this screen are grayed out.
VM5404D / VM5808D User Manual
62
Permission Level
At the bottom of the New/Edit User page is the permission section, whi ch is
used to set a user’s permi ssion level.
The three available permission levels are as follows:
Administrator – this level provides full access and control of the
VM5404D / VM5808D, in addition to full User Management
privileges.
Advanced User – this level provides full access and control with no
User Management privileges.
Basic User – this level only provides basic functions (connections and
open profiles).
Chapter 4. Browser Operation
63
Port Name
The Port Name page lets you name the input and outpu t ports for easy
identification.
To name an Input/Output port, enter a descripti ve name of up to 16
multi-language characters (excluding :;=[]+=/?\|) in the corresponding
field and click Save.
Language characters available include: English, French, German,
Italian, Japanese, Korean, Portuguese, Russian, Spanish, Simplified
Chinese and Traditional Chinese.
To change an Input/Output port’s name, enter another value and click
Save.
Input and Output port names can be the same.
Press Cancel to go back a level, return to the initial screen, or exit.
VM5404D / VM5808D User Manual
64
Network
The Network page lets you configure the IP settings, website tim eou t, and
Telnet settings for connecting to the VM5404D / VM5808D.
Enable DHCP to allow the DHCP server to assign an IP address to the
VM5404D / VM5808D . Select Disable to enter your own static IP address
settings for the device.
Click Cancel to use the following defau lt values:
IP Address – 192.168.0.60
Subnet Mask – 255.255.255.0
Default Gateway – 192.168.0.1
Websit e Timeout* – 5 minutes
Telnet Enabled
Enter the values, then click Save. Changes may take a few seconds and after
refreshing the page automatically redirects you to the IP address specified.
*This option controls how long an inactive web connection stays logged
into the VM5404D / VM5808D. Use N/A to disable this option. Other
options include 5, 10, 30 and 60 minutes. Any changes will take effect
immediately.
Chapter 4. Browser Operation
65
EDID
The EDID Settings page lets users view and select an EDID Mode so that the
VM5404D / VM5808D can use the best resolution for its display(s).
Note: The EDID Mode can also be selected via the Front Panel pushbuttons –
see EDID Mode, page 25.
Extended Display Identification Data (EDID) is a data format that contains a
display's basic information and is used to communicate with the video source/
system.
VM5404D / VM5808D User Manual
66
EDID Mode
In the left panel of the page, users can select a pre-configured EDID Mode
using the EDID Mode radio butto ns.
Select the EDID Mode to use and click Apply. The VM5404D / VM5808D
uses the settings configured for that ED ID m ode.
Options are:
ATEN Default: All ports' ED ID are the same as the hardware default
EDID.
Port 1 Mode: All ports' EDID are the same as Port1's EDID.
Remix: All ports' EDID use the best display resolution.
Customized: See Customized Mode, see page 69.
Chapter 4. Browser Operation
67
Customized Mode
Use the Customized Mode to automatically retrieve and save the EDID settings
of a connected monitor/ display device to an input source port.
In the left-most panel of the page, select Customized from the EDID
Mode section and click Apply.
Port EDID Status: Select which input source port you want to store
the EDID configuration (01–08).
Retrieve EDID: Click and a pop-up window appears to retrieve the
EDID settings of a stored EDID configuration: Customized EDID 01-
08, or ATEN Default. Select the port to retrieve:
The right panel displays a summary of the acquired EDID settings that
you can edit. Click Save and select the configuration for the Current
or All Ports for the duration of the sessio n .
VM5404D / VM5808D User Manual
68
EDID & CEA Description
The right panel of the screen lets users view the configuration of the EDID and
CEA Modes selected:
From the left column, click the option that you want to view and/or
edit. There are two categories: EDID (Extended Display Identification
Data) and CEA (Consumer Electronics Association).
When you highlight the menu items on the left column, the right
column displays the current settings for the corresponding EDID
configuration. Some of the screens are read-only.
See Customized EDID Settings, page 69 for more information on these
two columns.
Chapter 4. Browser Operation
69
Customized EDID Settings
The EDID structure is comprised of 128 bytes in total – each heading shown in
the left column corresponds to a specific number of bytes.
The pages for the pre-configured EDID Modes (Port 1, Default and Remix)
cannot be edited. The pages for the Customized EDID, which can be edited, are
discussed in the proceeding sections:
Established Timings
This page lists video resolutio ns/timings that display devices can support.
Select the resolution(s) you want to use for the attached monitor/
display device.
Click Clear to deselect all the items.
Click Select All to check all the items.
Click Save to apply the changes.
VM5404D / VM5808D User Manual
70
Standard Timings
This page shows eight resolutions/ tim ings that display devices can support in
addition to those listed in the Established Timings page.
Select the H Active Pixel from the drop-down menu.
Select the Aspect Ratio from the drop-down menu.
Click Save to apply the changes.
Detail Timing / Display Description
This screen gives more video resolution options, and provides resolution/
timing details.
In the drop down menu, choose a resolution with values that fit the attached
monitor/display device and click Save.
Chapter 4. Browser Operation
71
Monitor Description
This screen lets you specify the viewing specifications, namely horizontal and
vertical scan ranges and pixel clock rate, of your monit or/display device.
Enter the values that correspond to your device and click Save to apply the
changes.
VM5404D / VM5808D User Manual
72
Firmware
The Maintenance page lets users upgrade the VM5404D / VM5808D’s
firmware and back up or restore system settings. This is an Administrator only
function.
To upgrade the VM5404D / VM5808D ’s firm ware, do the following:
1. Use the Browse button to locate the firmware upgrade file. Make sure you
have the correct file saved on your PC.
2. Click Upgrade to begin the upgrade procedure.
Note: After updating the firmware, it’ s recommended that you clear your web
browser’s cache and then close and reopen the web browser. This will
ensure the GUI refreshes and functions properly.
To back up the VM5404D / VM5808D’s system setting s, do the following:
1. Click Backup. A configuration file will then begin downloading.
To restore the VM5404D / VM5808D’s system settings, do the following:
1. Use the Browse button to locate the configuration file. Make sure you
have the correct file saved on your PC.
2. Click Restore to begin the restoration procedure.
Note: User accounts cannot be backed up or restored.
Chapter 4. Browser Operation
73
HDCP
The HDCP page lets users view and set HDCP key settings between input and
output ports for digital copy protection and to ensure Seamless Switching
between different devices. This is an Administrat or and Advance d User only
function.
Input
Here users can select whether input port content is HDCP 1.4 or non-HDCP
enabled.
Connection
Here users can find a visual display of connection paths between in puts and
outputs. When selecting an input, its path is displayed in green.
Output
Here users can define whether or not HDCP settings are fixed, either by
individual port or by applying one setting to all ports. By prearranging and
fixing keys, this setting ensures that Seamless Switching is possible even when
switching between HDCP and non-HDCP enabled devices.
VM5404D / VM5808D User Manual
74
OSD
The OSD page lets users view and set OSD settings for all ports.
OSD: Sets the default OSD option for the port. When OSD is on, real-
time text updates appear on the display for 10 seconds when
configuration and port changes are made to its output.
Use the drop-down menu to apply options to all ports, or ON/OFF
button to enable/disable the OSD for each port.
Click Save to save the settings or Cancel to exit witho ut savin g the
settings.
Chapter 4. Browser Operation
75
Telnet Operation
The VM5404D / VM5808D can be operated and confi gured via a remote
terminal session using Telnet.
To log into the VM5404D / VM5808D by means of a Telnet session, do the
following:
1. On your computer, open a terminal (command line) session.
2. At the prompt, key in the VM5404D / VM5808D’s IP address in the
following way:
telnet [IP address]:23
3. Press Enter. The login screen appears. At the login prom pt, provide your
Username and Password.
Note: If a user logs on using a Username that is already in session, the newest
login takes effect and the previous session is replaced.
Configuration Menu
Once a Telnet connection to the VM5404D / VM5808D is established, the
device’s text-based Configuration Menu comes up, with the following items:
1. H – Call up the command list for help
Command list:
GT – Set gateway address
IM – Set IP subnet mask
IP – Set IP address
LO – Load connections from profile nn
PW – Change password
RI– Read what input is connected to nn output
RO – Read what output is connected to nn input
SB – Set the serial port baud rate
SS – Switch input to specifi ed port
SV – Save the current connections int o pro fi le nn
TI – Set timeout
VM5404D / VM5808D User Manual
76
VR – Software version information
Ctrl-Q – Quit
2. GT – Set gateway address
GT
Old gateway address: 192.168.0.1
New gateway address:
3. IM – Set IP subnet mask
IM
Old IP subnet mask: 255.255.255.0
New IP subnet mask:
4. IP – Set IP address
IP
Old IP address: 192.168.0.60
New IP address:
5. LO – Load connections fr om pr ofile
LO 01
Load profile 01 OK.
6. PW – Change password
PW
Old password: ********
New password:
7. RI – Read what input is connected to nn output
RI 01
Input port 02 04 08 is connected to outp ut port 01
Chapter 4. Browser Operation
77
8. RO – Read what output is connected to nn input
RO 01
Output port 02 is connected to input port 01
9. SB – Set serial port baud rate
SB 96
Serial port baud rate is set to 9600
10. SS – Switch input to specified output
SS 01,03
Switch input 01 to output 03
11. SV – Save the current connections into a profile
SV 01
Save the current connections into profile 01
12. TI – Set timeout
TI 30
Set 30 minute timeout
13. VR – Sof tware version information
VR
Software version 1.0.
Note: For further information about these functions, please reference the
equivalent Browser GUI functions earlier in this chapter.
VM5404D / VM5808D User Manual
78
This Page Intentionally Left Blank
79
Chapter 5
RS-232 Commands
Serial Control Protocol Commands
The VM5404D / VM5808D’s built-in bi-directional RS-232 serial interface
allows system control through a high-en d control ler or PC. The RS-232
commands for the VM5404D and VM5808D are the same, with th e only
difference being that the VM5808D has 4 additional ports.
RS232 Pin Assignment
Configuring the Serial Port
The controller’s serial port should be conf ig ured as follows:
Pin Description Pin Description
1 Not connected 6 Not connected
2 RXD 7 Not connected
3 TXD 8 Not connected
4 Not connected 9 Not connected
5GND
Baud Rate 19200
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
VM5404D / VM5808D User Manual
80
Verification
After entering a command, a verification message appears at the end of the
command line as follo ws:
Command OK - indicates that the command is correct and successfully
performed by the switch
Command incorrect - indicates that the command has the wrong format
and/or values.
Chapter 5. RS-232 Commands
81
Switch Port Command
The Switch Port command allo ws you to swit ch ports on the VM5404D /
VM5808D.
The formula for the Switch command is as follows:
Command + Input + Number + Output + Number + Control + [Enter]
1. For example, to switch input port 02 to ou tput port 05, type:
sw i02 o05 [Enter]
2. To switch output port 04 to the next port, type:
sw o04 + [Enter]
3. To turn off video output on port 03, type:
sw o03 off [Enter]
The following tables show the possible values for the Switch Port command:
Command Description
sw Switch command
Input Command Description
i Input command
Port number Description
xx 01-08 port
Output Command Description
o Output command
Port number Description
yy 01-08 port
* All output ports
Control Description
on Turn on the display
off Turn off the display
+Next Port
-Previous Port
VM5404D / VM5808D User Manual
82
Note: 1. By default, input port 01 is tied to output port 01; input port 02 is tied
to output port 02; and so on until port 08 (i.e., o01 i01, o02 i02).
2. Each command string can be separated with a space.
3. The Port Number can be skipped, and the default value will be used.
The following table lists the available Switch Port commands:
Command Input
Command Input
Port Output
Command Output
Port Control Enter Description
sw i xx o yy
*
[Enter] Switch Input Port xx to
Output Port yy
(xx:01~08; yy:01~08,
*)
sw o yy
*
on
off
[Enter] Turn on Output Port yy
Turn off Output Port yy
(yy:01~08, *)
sw o yy
*
+
-
[Enter] Switch Output port yy
to next Output port.
Switch Output port yy
to previous Output
port.
(yy:01~08, *)
Chapter 5. RS-232 Commands
83
EDID Mode Command
Extended Display Identification Data (EDID) is a data that contains a display's
basic information and is used to communicate with th e video source.
The formula for the EDID command is as follows:
Command + Control + [Enter]
1. For example, to use the Port1 EDID mode, type:
edid port1 [enter]
The following tables show the possible values for the EDID command:
Note: Each command string can be separated with a space.
The following table lists the available EDID commands:
Command Description
edid EDID Mode command
Control Description
port1 Implement the EDID of the connected
display to Port 1, and pass it to the
video source.
remix Implement the EDID of each
connected display according to its
connection when the VM5808D is first
powered on, or immediately after
selecting the Remix option.
default Implements ATEN’s default EDID.
(default)
custom Implements the customized mode as
set in the EDID system settings.
(See Customized EDID Settings,
page 69)
Command Control Enter Description
edid port1 [Enter] The EDID from Port 1 is passed to the video
source.
edid remix [Enter] The VM5404D / VM5808D implements the
EDID of each connected display according to
its connection when the VM5808D is first
powered on, or immediately after selecting the
Remix option.
edid default [Enter] ATEN’s default EDID is passed to the video
source.
VM5404D / VM5808D User Manual
84
EDID custom [Enter] Implements the customized mode.
Command Control Enter Description
Chapter 5. RS-232 Commands
85
Mute Command
Mute allows you to enable or disable an output port(s) audio.
The formula for the Mute command is as follows:
Command + Output + Number + Control + [Enter]
1. For example, to mute the audio coming from output port 1, type:
mute o01 on [enter]
The following tables show the possible values for the Mute command:
Note: 1. Each command string can be separated with a space.
2. Sk ip th e output port command to mute or enable the audio of all
output ports.
The following table lists the available Mute commands:
Command Description
mute Mute command
Output Command Description
o Output command
Port number Description
yy 01-08 port (default is 01)
* All output ports
Control Description
on Mute on; audio from DVI output port is
disabled
off Mute off; audio output enabled
(default)
Command Output
Command Output
Port Control Enter Description
mute oyy
*
on [Enter] Audio on for output port yy
(yy:01~08, *)
mute oyy
*
off [Enter] Audio off for output port yy
(default)
(yy:01~08, *)
VM5404D / VM5808D User Manual
86
Scaling Command
The Scaling command allows you to set a resolution for scaling the display
connected to an output port.
The formula for the Scaling command is as follows:
Command + Output + Nu mber 1 + Horizontal Resolution + Number 2
+ Vertical Resolution + Number 3 + Frequency + Number 4 + Contr ol
+ [Enter]
1. For example, to turn scaling off for output port 02, type:
scaling o02 off [Enter]
2. To set the scaling for output port 04 to 1920x1080@60Hz, type:
scaling o04 1080p [Enter]
3. To set the scaling for all output ports to the connected display’s native
resolution, type:
scaling o* native [Enter]
The following tables show the possible values for the Scaling command:
Command Description
scaling Scaling command
Output Description
o Output command
Port Number Description
yy 01-08 port
* All output ports
Horizontal
Resolution Description
hor Horizontal resolution command for
scaling
Resolution Number Description
hhhh Horizontal resolution
Vertical Resolution Description
ver Vertical resolution command for
scaling
Chapter 5. RS-232 Commands
87
Note: 1. Each command string can be separated with a space.
2. The Port Number command string can be skipped, and the default
value will be used.
The following table lists the available Scaling commands:
Resolution Number Description
vvvv Vertical resolution
Frequency Description
freq Frequency command for scaling
Frequency Number Description
fff Frequency resolution
Control Description
off Turn off the scaling function
(by pass mode)
native Map display's native resolution for
scaling (default)
Comm
and Outp
ut
Port
Numb
er
Horiz
ontal
Resol
ution
Numb
er
Vertic
al
Resol
ution
Numb
er Frequ
ency Numb
er Contr
ol Enter Description
scaling oyy
*
off [Enter
]
Turn off
scaling for
port yy (by
pass mode)
yy: 01 ~ 08 or
*
scaling oyy
*
native [Enter
]
Enable
display’s
native
resolution for
scaling on
output port yy
(default)
yy: 01 ~ 08 or
*
VM5404D / VM5808D User Manual
88
scaling oyy
*
hor 1920 ver 1080 freq 60 [Enter
]
Scale output
port yy to
1920x1080@
60Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1920 ver 1080 freq 50 [Enter
]
Scale output
port yy to
1920x1080@
50Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1280 ver 720 freq 60 [Enter
]
Scale output
port yy to
1280x720@6
0Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1280 ver 720 freq 50 [Enter
]
Scale output
port yy to
1280x720@5
0Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1920 ver 1200 freq 60 [Enter
]
Scale output
port yy to
1920x1200@
60Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1600 ver 1200 freq 60 [Enter
]
Scale output
port yy to
1600x1200@
60Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1400 ver 1050 freq 60 [Enter
]
Scale output
port yy
to1400x1050
@60Hz
yy: 01 ~ 08 or
*
Comm
and Outp
ut
Port
Numb
er
Horiz
ontal
Resol
ution
Numb
er
Vertic
al
Resol
ution
Numb
er Frequ
ency Numb
er Contr
ol Enter Description
Chapter 5. RS-232 Commands
89
scaling oyy
*
hor 1280 ver 1024 freq 60 [Enter
]
Scale output
port yy to
1280x1024@
60Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1024 ver 768 freq 60 [Enter
]
Scale output
port yy to
1024x768@6
0Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1600 ver 900 freq 60 [Enter
]
Scale output
port yy to
1600x900@6
0Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 1280 ver 800 freq 60 [Enter
]
Scale output
port yy to
1280x800@6
0Hz
yy: 01 ~ 08 or
*
scaling oyy
*
hor 720 ver 576 freq 50 [Enter
]
Scale output
port yy to
720x576@50
Hz
yy: 01 ~ 08 or
*
Comm
and Outp
ut
Port
Numb
er
Horiz
ontal
Resol
ution
Numb
er
Vertic
al
Resol
ution
Numb
er Frequ
ency Numb
er Contr
ol Enter Description
VM5404D / VM5808D User Manual
90
Fan Speed Command
The Fan Speed command allows you to set the VM5808D’s internal fan speed.
Note: This feature is not supported by the VM5404D.
To set the fan speed, use the following command:
Command + Control + [Enter]
1. For example, to set the fan to low speed, type:
fan low [Enter]
The following tables show the possible values for the Fan Sp eed command:
Note: Each command string can be separated with a space.
The following table lists the available Fan Speed commands:
Command Description
fan Fan Speed Command
Control Description
low Set internal fan to low speed (default)
mid Set internal fan to normal speed
high Set internal fan to high speed
Command Control Enter Description
fan low [Enter] Sets fan speed to low
fan mid [Enter] Sets fan speed to normal
fan high [Enter] Sets fan speed to high
Chapter 5. RS-232 Commands
91
Echo Command
The Echo function updates the RS232 controller when operations are made via
the front panel pushbuttons, web browser, or telnet. The changes echo back to
the RS232 controller to keep the settings in sync with the device.
The formula for the Echo command is as follows:
Command + Control + [Enter]
1. For example, to enable the echo feature, type:
echo on [Enter]
The following tables show the possible values for the Echo command:
Note: Each command string can be separated with a space.
The following table lists the available Echo commands:
Command Description
echo Echo command
Control Description
on Turns Echo function on
off Turns Echo function off (default)
Command Control Enter Description
echo on [Enter] Turn on Echo function
echo off [Enter] Turn off Echo function
VM5404D / VM5808D User Manual
92
Black Screen Command
The Black Screen command turns a display screen black when no source signal
is detected. This prevents the display from showing the default blue or other
color used when no source signal is detected.
The formula for the Black Screen command is as follows:
Command + Control + [Enter]
1. For example, to enable the Black Screen function, type:
blackscreen on [Enter]
The followin g tables show the possible values for the Black Screen command:
Note: Each command string can be separated with a space.
The following table lists the available Black Screen commands:
Command Description
blackscreen Black Screen command
Control Description
on Turns Black Screen function on
(default)
off Turns Black Screen function off
Command Control Enter Description
blackscreen on [Enter] Turn on Black Screen function
blackscreen off [Enter] Turn off Black Screen function
Chapter 5. RS-232 Commands
93
Read Command
The Read command allows you to view information abo ut the device.
The formula for the Read command is as follows:
Command + [Enter]
1. To view information, type:
read [Enter]
The following table shows the possible values for the Read command:
The following table lists the available Read commands:
The following is an example of the information the system will provide when
the Read command is used:
read Command OK
o01 i03 video on audio on 1920x1 080@60(1080p)
o02 i04 video off audio off bypass
o03 i02 video on audio off 1600x12 00@60
Which means:
1. o01 i03 video on audio on 1920x1080@60(1080p)
Output 01 is connected to Input 03 with vid eo and audio on; the resolution is
scaled to 1080p at 60Hz
2. o02 i04 video off audio off bypass
Output 01 is connected to Input 03 with vid eo audio off; scaling is bypassed
(turned off)
3. o03 i02 video on audio off 1600x1200@60
Output 03 is connected to Input 02 with video on and audio off; the resolution
is scaled to 1600x1200 at 60Hz
Command Description
read Read command
Command Enter Description
read [Enter] Reads information from the
device
VM5404D / VM5808D User Manual
94
Reset Command
The Reset command allows you to reset the VM5404D / VM5808D to the
default factory settings.
The formula for the Reset command is as follows:
Command + [Enter]
The following tables show the possible values for the Reset command:
Note: Each command string can be separated with a space.
The following table lists the available Reset commands:
Command Description
reset Reset command
Command Enter Description
reset [Enter] Resets the device settings
Chapter 5. RS-232 Commands
95
Baud Rate Command
The Baud Rate command allows you to set the RS-232 da ta rate for the
VM5404D / VM5808D to use. Options are 9600, 19200 (default) 38400 and
115200.
The formula for the Baud Rate command is as follows:
Command + Control + [Enter]
1. For example, to set 38400 as the baud rate, type:
baud 38400 [Enter]
The following tables show the possible values for the Baud Rate command:
Note: Each command string can be separated with a space.
The following table lists the available Baud Rate commands:
Command Description
baud Sets the RS-232 baud rate
Control Description
9600 Use 9600 baud rate
19200 Use 19200 baud rate (default)
38400 Use 38400 baud rate
115200 Use 115200 baud rate
Command Control Enter Description
baud 9600 / 19200 / 38400 /
115200
[Enter] Sets the RS-232 baud
rate
VM5404D / VM5808D User Manual
96
Save/Load Profile Command
The Save/Load Profile command allows you to save and load conn ect ion
profiles. Saving profiles will save the connections currently in use.
The formula for the Save/Load Profile command is as follows:
Command + Profile + Number + Control + [Enter]
1. For example, to save the current conn ectio n configuration to profile 02,
type:
profile f 02 save [Enter]
The following tables show the possible values for the Save/Load Profile
commands:
Note: Each command string can be separated with a space.
The following table lists the available Save/Load Profile commands:
Command Description
profile Save / Load profile
Profile Description
f Profile command
Profile Number Description
yy VM5404D: 01-08 (default is 01)
VM5808D: 01-16 (default is 01)
Control Description
save Save the connection configuration
load Load a saved profile
Command Profile Profile
Number Control Enter Description
profile fyy
*
save [Enter] Save the connections as profile yy.
VM5404D: (yy:01~08, *)
VM5808D: (yy:01~16, *)
profile fyy
*
load [Enter] Load profile yy.
VM5404D: (yy:01~08, *)
VM5808D: (yy:01~16, *)
Chapter 5. RS-232 Commands
97
OSD Command
To enable or disable the On-Screen Display (OSD) for displays, use the
followin g co mmand:
Command + Output + Number + Control + [Enter]
1. For example, to enable the OSD for output 07, type:
osd o07 on [Enter]
2. For example, to disable the OSD for all outputs, type:
osd o* off [Enter]
The following tables show the possible values for the OSD command:
Note: Each command string can be separated with a space.
The following table lists the available OSD commands:
Command Description
osd OSD command
Output Description
o Output port command
Number Description
yy Output port
01~16 port (default is 01)
* All output ports
Control Description
on Enable OSD function
off Disable OSD function (default)
Command Output
Command Output
Port Control Enter Description
osd oyy
*
on [Enter] OSD on for output yy
yy:01~16, *
osd oyy
*
off [Enter] OSD off for output yy
(default)
yy:01~16, *
VM5404D / VM5808D User Manual
98
Alert Command
To trigger a warning when issues arise for a specific input port, use the
following command:
Command + Input + Number + Control + [Enter]
1. For example, to enable the basic Alert function for input port 1, type:
alert i01 m1 [enter]
The following tables show the possible values for the Alert command:
Note: Each command string can be separated with a space.
Command Description
alert Alert command
Input Description
i Input command
Port number Description
yy VM5404D: 01-04
VM5808D: 01-08
Control Description
off Disable Alert (default)
m1 Show basic Alert (flashing border)
m2 Show detailed Alert (flashing border
and port information)
Chapter 5. RS-232 Commands
99
The following table lists the available Alert commands:
Command Input
Command Input Port Control Enter Description
alert iyy
off [Enter] Alert off for input port yy
VM5404D (yy:01~04)
VM5808D (yy:01~08)
alert iyy
m1 [Enter] Basic Alert on for input port yy
VM5404D (yy:01~04)
VM5808D (yy:01~08)
alert iyy
m2 [Enter] Detailed Alert on for input port yy
VM5404D (yy:01~04)
VM5808D (yy:01~08)
VM5404D / VM5808D User Manual
100
This Page Intentionally Left Blank
101
Appendix
Safety Instructions
General
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
This product is for indoor use only.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage wi ll resul t.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be bl ocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device shoul d be oper ated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V
phase-to-phase voltage.
To prevent damage to your installation it is important that all devices are
properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug . Always follow your local/national
wiring codes.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
VM5404D / VM5808D User Manual
102
If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
un-interruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yoursel f. Refer all servicin g to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
Avoi d circui t overloads. Before connecting equipment to a circuit, know
the power supply’s limit and never exceed it. Always review the electrical
specifications of a circuit to ensure that you are not creating a dangerous
condition or that one does not already exist. Circui t overloads can cause a
fire and destroy equipment.
Appendix
103
Rack Mounting
Before working on the rack, ma ke sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflow is provided to devices in the rack.
Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer.
Do not step on or stand on any device when servicing other devices in a
rack.
VM5404D / VM5808D User Manual
104
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://eservice.aten.com
For telephone support, see Telephone Suppo rt, page iv:
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Yo ur com puter configuration, including operating syst em, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
Telephone Support 1-888-999-ATEN ext 4988
Appendix
105
Specifications
Function VM5404D VM5808D
Video Input Interface 4 x DVI-D Female
(White)
8 x DVI-D Female
(White)
Impedance 100 Ω
Max. Distance 1.8 m
Video
Output
Interface 4 x DVI-D Female
(White)
8 x DVI-D Female
(White)
Impedance 100 Ω
Video Max. Data Rate 6.75 Gbps (2.25 Gbps Per Lane)
Max. Pixel Clock 225 MHz
Compliance HDCP 1.4 Compatible
Max. Resolution Up to 1920 x 1200
Max. Distance Up to 5 m
Control RS-232 Connector: 1 x DB-9 Female (Black)
Baud Rate and Protocol: Baud Rate: 19200, Data
Bits: 8, Stop Bit: 1, Parity: No, Flow Control: No
IR 1 x Mini Stereo Jack Female (Black)
Ethernet 1 x RJ-45 Female (Black)
EDID Settings EDID Mode: Default / Port 1 / Remix / Customized
Power Connector 1 x 3-Prong AC Socket
I/P Rating 100-240VAC; 50-60Hz; 1.0A
Consumption 120VAC, 34.1W;
230VAC, 34.4W
120VAC, 56.4W;
230VAC, 55.9W
Environme
nt
Operating Temp. 0–50ºC
Storage Temp. -20–60ºC
Humidity 0–80% RH, Non-condensing
Physical
Properties
Housing Metal
Weight 3.50 kg 4.25 kg
Dimensions (L x W x
H)
43.24 x 25.98 x 4.4 cm
VM5404D / VM5808D User Manual
106
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILI TY EXCE ED THE PRICE PAID
FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESUL TING FRO M THE USE OF THE PRODUCT, DISK,
OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with
respect to the contents or use of this documentation, and especially disclaims its quality,
performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or
documentation without obligation to notify any indivi dual or entity of such
revisions, or update. For further inquiries, please contact your direct vendor.