Beko BDIN16421 User Manual
Displayed below is the user manual for BDIN16421 by Beko which is a product in the Dishwashers category. This manual has pages.
Related Manuals
Dishwasher
User’s Manual
EN
15 8725 0100-AA_BEKO_E10_EN/ 12-02-21.(12:42)
BDIN...
The following symbols are used in the user manual and on the packaging:
Danger that may result in death or injury.
NOTICE
Danger that may result in damage to the product or its surroundings.
Important information or useful hints about usage.
Read the user manual.
Dear Customer,
Please read this user manual before using the product.
Thank you for choosing this Beko product. We hope that you get the best results
from your product which has been manufactured with high quality and state-of-the-art
technology. Therefore, please read this entire user manual and all other accompanying
documents before using the product.
Follow all warnings and information in the user manual. Thus, you can protect yourself
and your product against potential dangers.
Keep the user manual. If you handover the product to someone else, give the user
manual as well.
This product was manufactured using the latest technology in environmentally friendly conditions.
CONTENTS
1 SAFETY INSTRUCTIONS 4
Intended Use ..................................................... 4
Safety for children, vulnerable persons and pets 4
Electrical safety ................................................. 5
Transportation Safety ........................................ 5
Installation Safety .............................................. 6
Operational safety ............................................. 7
Maintenance and cleaning safety ...................... 8
Interior Lighting .................................................. 8
2 ENVIRONMENTAL
INSTRUCTIONS 8
Compliance with WEEE Directive and Disposing
of the Waste Product ......................................... 8
Package information .......................................... 9
Technical specifications ................................... 10
3 YOUR DISHWASHER 11
Overview...........................................................11
4 INSTALLATION 12
Appropriate installation location....................... 12
Connecting water supply ................................. 12
Aquasafe+Aquasafe ....................................... 13
Connection to the drain ................................... 14
Adjusting the feet ............................................. 14
Electrical connection........................................ 14
5 PREPARATION 15
Tips for energy saving ..................................... 15
Water softening system ................................... 15
Adjusting the water softening system .............. 15
Adding salt ....................................................... 16
Detergent ......................................................... 16
Tablet detergents ............................................. 18
Rinse aid.......................................................... 18
Items not suitable for washing in the
dishwasher ...................................................... 19
Placing the dishes into the dishwasher ........... 19
Cutlery basket ................................................. 21
Cutlery basket ................................................. 21
Collapsible lower basket tines ......................... 22
Collapsible lower basket tines ......................... 22
Tray Wash Supports ........................................ 23
SoftTouch Accessory ....................................... 23
Lower Basket Glass Holder ............................. 23
Lower basket multipurpose / height adjustable
service rack ..................................................... 24
Lower basket bottle wire .................................. 25
Upper basket height adjustable rack ............... 25
Upper basket multipurpose service rack ......... 25
Upper basket multi-function service rack......... 26
Adjusting the height of the upper basket ......... 27
Adjusting the height of the upper basket ......... 28
Collapsible upper basket wires ........................ 29
Height setting with empty basket ..................... 29
Ceiling cutlery basket ...................................... 30
Ceiling cutlery basket ...................................... 30
6 OPERATING THE PRODUCT 31
On/Off key ....................................................... 31
Programme Selection / Programme Cancel key 31
Function Keys .................................................. 31
Preparing the machine .................................... 31
Programme selection....................................... 31
Auxiliary functions............................................ 31
Programming the washing time ....................... 34
Starting the programme ................................... 35
Cancelling the programme .............................. 35
Salt Indicator ( ) ......................................... 35
Rinse Aid Indicator ( ) .................................. 35
Adjusting the amount of rinse aid .................... 35
End of programme ........................................... 36
Water Cut-off Warning ..................................... 36
Overflowing Warning ....................................... 36
InnerClean ....................................................... 36
7 MAINTENANCE AND
CLEANING 37
Cleaning the outer surface of the product ....... 37
Cleaning the interior of the machine ................ 37
Cleaning the filters ........................................... 37
Cleaning the hose filter .................................... 38
Cleaning the impellers ..................................... 39
Lower impeller ................................................. 39
Upper impeller ................................................ 39
8 TROUBLESHOOTING 40
4/EN
Safety Instructions
•This section contains safety
instructions that will help get
protected against risks of
personal injury or property
damage.
•Our company shall not be
responsible for damages
that may arise when these
instructions are not followed.
Installation and repair
procedures must always be
performed by the manufacturer,
authorised service agent or a
qualified person specified by the
importer.
Only use original parts and
accessories.
Do not repair or replace
any part of the product unless
specified expressly in the user
manual.
Do not make any technical
modifications to the product.
Intended Use
This product is designed to
be used in houses and indoor
places. For example:
- Personnel kitchens in
stores, offices and other working
environments;
- Farm houses;
- Areas used by customers
at hotels, motels and other types
of accommodation;
- Bed&breakfast type
hotels, boardinghouses.
This product must be used to
do the domestic type dishes
only.
This product is not suitable for
commercial or collective use.
•The service life of your
product is 10 years. During
this period, original spare
parts will be available to
operate the product properly.
Safety for children,
vulnerable persons and
pets
This product can be used
by children at and above 8
years old and by persons
whose physical, sensory or
mental capabilities were not
fully developed or who lack
experience and knowledge
provided that they are
supervised or trained on the
safe usage of the product and
the risks it brings out.
Children below the age of
3 must be kept away from
the product unless they are
continuously supervised.
Electrical products are
dangerous for children and
pets. Children and pets must
not play with, climb on or
enter inside the product.
Do not forget to close the
door of the product when
leaving the room where it is
located. Children and pets
may remain locked inside the
product and suffocate.
1-
5/EN
Cleaning and user
maintenance works should
not be performed by children
unless they are supervised by
someone.
Keep packaging materials
away from children. There
is the risk of injury and
suffocation.
Store all detergents and
additives used with the
product in a safe place away
from the reach of children.
For children's safety, cut the
power cable and break the
locking mechanism so that it
will be non-functional before
disposing of the product.
Electrical safety
The product must be
unplugged during installation,
maintenance, cleaning,
repairing and moving
procedures.
If the power cable is
damaged, it must be replaced
by a qualified person
specified by the manufacturer,
authorised service agent or
importer in order to avoid
potential dangers.
Do not squeeze the power
cable under or behind the
product. Do not place heavy
objects on the power cable.
Power cable must not be bent
excessively, pinched or come
into contact with any heat
sources.
Do not use extension cords,
multi-sockets or adapters to
operate the product.
Plug must be easily
accessible. If this is not
possible, the electrical
installation where the product
is connected must contain
a device which conforms to
the electrical regulations and
disconnects all poles from the
grid.
Do not touch the power plug
with wet hands.
Remove the plug from the
socket by gripping the plug
and not the cable.
Transportation Safety
Before transporting the
product unplug it and
disconnect its drain and water
supply connections. Drain the
remaining water in the product
completely.
Product is heavy, do not
move it alone.
NOTICE
Do not hold the
product from its door or panel to
move it.
NOTICE
If you need to move
the product, do it in upright
position and hold from the rear
side. Slanting the product to front
may cause the electronic parts in
it to get wet and damaged.
NOTICE
Make sure that
the hoses do not get kinked,
6/EN
squeezed or crushed while
placing the product into its
location after installation or
cleaning procedures.
Installation Safety
•To make the product ready for
use, review the information
in the user manual and
installation instructions and
make sure that the electricity,
water supply and drain
systems are appropriate. If
they are not, call a qualified
technician and plumber
to have the necessary
arrangements carried out.
These procedures are under
customer’s responsibility.
•Prior to installation, check
if the product has any
defects on it. If the product
is damaged, do not have it
installed.
•Do not install the product
in environments where the
temperature falls below 0ºC.
Do not place the product on
carpets or similar surfaces.
This may cause fire hazard
since the product will not be
ventilated from below.
Place the product on a clean,
flat and solid surface and
balance it with adjustable feet.
If the feet are not adjusted
properly, the door will not
be closed completely and
cause hot steam to escape.
Otherwise, it might cause
serious burns and injuries,
and harm your furniture.
Do not install the product
close to heat sources (heater,
stove and etc.) or under the
cooking area of a hob.
•If the product is going to
be used inside a wardrobe/
cabinet/module, keep the
doors of the wardrobe/cabinet/
module open during operation
in cases where there are no
openings to provide sufficient
air circulation.
Plug the product in a
grounded socket protected
by a fuse with current
values as per type label
of the product. Have the
grounding installation made
by a qualified electrician. Do
not use the product without
having the grounding made as
per local/national regulations.
Plug the product in a socket
that conforms the voltage and
frequency values stated on
the type label of the product.
Do not plug the product
in sockets that are loose,
dislocated, broken, dirty,
greasy or bear the risk of
getting in contact with water,
such as places where there
might be water leak from the
counter.
NOTICE
You must use the
new hose set provided with the
product. Do not reuse the old
7/EN
hose set. Do not make extension
at the hoses.
NOTICE
Connect the water inlet
hose directly to the water tap.
Pressure coming from the tap
should be 0.03 MPa (0.3 bars)
minimum and 1MPa (10 bars)
maximum. If the water pressure
exceeds 1 MPa (10 Bars), a
pressure relief valve should be
installed in between.
Route the power cable and
hoses in a way that they do
not cause risk of tripping.
Operational safety
•Only dishwasher safe
detergents, rinse aids and
additives must be used.
Never use chemical solvents
in the product. They bring
forth the risk of explosion.
The wash-water inside the
product is not potable.
Dishwasher detergents have
high alkali content and can
be very dangerous when
ingested. Avoid letting them
get into contact with skin and
eyes and keep children away
from the product when its
door is open. Make sure that
the detergent dispenser is
empty after the washing cycle
is complete.
When you pull the upper and
lower baskets out completely,
the door of the product will
bear all the weight of the
baskets. Do not sit or put
other loads on the door;
otherwise, the product may
tilt.
Maximum washing capacity
of the product is stated in the
section called
“Technical
Specifications”
.
To prevent possible injuries,
always place the sharp and
pointed dishes such as
service fork, bread knife,
etc. upside down so as their
pointed ends face down or
they lie horizontally in the dish
basket.
Open the door of the product
carefully if you need to do so
when the product is running.
Be careful against hot steam
that may escape or hot water
that may spill.
Do not start the broken or
damaged product. Unplug
the product (or switch off the
fuse it is connected to), turn
off the water tap and call the
authorised service agent.
Do not place flame sources
(lit candles, cigarettes, etc.)
on or close to the product.
Do not keep combustable/
flammable substances close
to the product.
Do not climb on the product.
•Unplug the product and close
the tap if you are not going to
use it for a long time.
8/EN
Maintenance and cleaning
safety
Do not wash the product by
spreading or pouring water
onto it.
Do not use sharp or abrasive
tools when cleaning the
product. Do not use home
cleaning products, detergent,
gas, gasoline, thinner, alcohol,
varnish etc.
NOTICE
Do not forget to install
the product’s filter back after you
have cleaned it. Otherwise, pumps
will get clogged and product will be
damaged.
Interior Lighting
Depending on the model
of your product, call the
authorised service agent when
it is required to change the
LED/bulb used for lighting.
Environmental
Instructions
Compliance with WEEE
Directive and Disposing of
the Waste Product
This product complies with
EU WEEE Directive (2012/19/
EU). This product bears a
classification symbol for
waste electrical and electronic
equipment (WEEE).
This symbol indicates
that this product shall
not be disposed with
other household wastes
at the end of its service
life. Used device must
be returned to official collection
point for recycling of electrical
and electronic devices. To find
these collection systems please
contact to your local authorities
or retailer where the product was
purchased. Each household
performs important role in
recovering and recycling of old
appliance. Appropriate disposal
of used appliance helps prevent
potential negative consequences
for the environment and human
health.
Compliance with RoHS
Directive
The product you have purchased
complies with EU RoHS Directive
(2011/65/EU). It does not contain
harmful and prohibited materials
specified in the Directive.
2-
9/EN
Package information
Packaging materials of
the product are
manufactured from
recyclable materials in
accordance with our National
Environment Regulations. Do not
dispose of the packaging
materials together with the
domestic or other wastes. Take
them to the packaging material
collection points designated by
the local authorities.
10/EN
Technical specifications
Maximum washing capacity (check the
energy label and Programme data and
average consumption values table given
on Quick Guide. )
Height (check installation document for
installation)
Width: 60
Depth: 57
Power input: 220-240 V, 50 Hz *
Total power 1800-2100 W *
Heater power: 1800 W *
Total current: 10 A *
Pump power: 90 - 125 W *
Drain pump power: 30 W *
* For detailed electrical values, check
the type label on the machine door.
Water Pressure 0.3 –10 bar
(= 3 – 100 N/cm² = 0.03-1.0 Mpa)
Technical specifications may be
changed without prior notice to improve
the quality of the product.
Figures in this manual are schematic
and may not match the product exactly.
Values stated on the markings of the
product or in the printed documents
accompanying the product are
obtained in the laboratory on basis of
the relevant standards. These values
may vary according to the usage of the
product and ambient conditions.
Note for test institutions:
Data required for performance tests shall
be provided upon request. Requests can
be e-mailed to the following address:
dishwasher@standardloading.com
Do not forget to provide the code, stock
number and serial number of the product
to be tested in your request e-mail along
with your contact information. Code, stock
number and serial number of the product
may be found on the type label attached to
the side wall of the door.
Compliance to standards and test
data/EC declaration of conformity
Development, production and
sales stages of this product comply
with the safety rules included in all
pertaining European Community
regulations.
2014/35/EU, 2014/30/EU, 93/68/EC, IEC
60436 / EN 60436
The model information as stored in
the product database can be reached
by entering following website and
searching your model identifier (*)
found on energy label.
https://eprel.ec.europa.eu/
XXXXXXXXXX (*)
18 7575 8000
3:25
REV:AA
12.9 L
94
13 x
kWh
2019/2017
48
db
11/EN
Your dishwasher
Overview
1. Upper basket
2. Upper impeller
3. Lower impeller
4. Cutlery basket (depends on model)
5. Door
6. Rating Label
7. Control panel
8. Detergent dispenser
9. Lower basket
10. Filters
11. Salt reservoir lid
12. Upper basket rail
13. Upper cutlery basket (depends on model)
14. Tabletop (depends on model)
15. Fan drying system (depends on model)
3-
15
15
12/EN
Installation
Read “Safety Instructions” section first!
Installation procedures must always be
performed by the manufacturer, authorised
service agent or a qualified person
specified by the importer. To make the
product ready for use, make sure that
the electricity, tap water supply and water
drainage systems are appropriate before
calling the authorised service agent. If
they are not, call a qualified technician
and plumber to have the necessary
arrangements carried out.
Preparation of the location and
electrical, tap water and waste water
installations at the place of installation
is under customer's responsibility.
Installation and electrical connections
must be carried out by the authorised
service agent. Manufacturer shall
not be held responsible for damages
arising from processes carried out by
unauthorised persons.
Prior to installation, check if the product
has any defects on it. If the product
is damaged, do not have it installed.
Damaged products cause risks for your
safety.
Make sure that the water inlet and
discharge hoses are not folded,
pinched or crushed while pushing the
product into its place after installation
or cleaning procedures.
The front of the appliance may not be
removed on free-standing or under-the-
counter models. The warranty will be
void if this is done.
When placing the product, pay attention not
to damage the floor, walls, piping, etc. Do
not hold the product from its door or panel
to move it.
Appropriate installation location
In the area where this product is
installed, there must not be a lockable,
sliding or hinged door that will restrict
full opening of the product’s door.
Make sure that you select a location
that will allow you to load and unload
the dishes in a fast and comfortable
manner.
•Place the product on a solid and flat
floor that has sufficient load carrying
capacity! The product must be installed
on a flat surface in order for the door to
be closed properly and securely.
•Do not install the product at places
where temperature may fall below 0ºC.
•Place the product on a hard floor. Do
not place it on a long pile rug or similar
surfaces.
Do not place the product on the power
cable.
•Make sure that you select a location
that will allow you to load and unload
the dishes in a fast and comfortable
manner.
•Install the product at a place close to
the tap and the drain hole. Select the
installation location by considering
that it will not be changed after the
connections are made.
Connecting water supply
We recommend installing a filter at
the water inlet in order to prevent the
dirt (sand, clay, rust) in the mains or
water installation of your home from
damaging the machine or the dishes.
4-
13/EN
Permitted water temperature: up to
25°C ( 60°C for products equipped
with Aquasafe+Aquasafe; please
refer to Aquasafe+Aquasafe section
)
The dishwasher may not be connected to
open warm water devices or flow-through
water heaters.
NOTICE
Do not use an old or used water
inlet hose on the new product. Use the new
water inlet hose supplied with the product.
Do not make extension at the hoses.
NOTICE
Connect the water inlet hose
directly to the water tap. Pressure coming
from the tap should be 0.3 bars minimum
and 10 bars maximum. If the water
pressure exceeds 10 bars, a pressure relief
valve should be installed in between.
NOTICE
The water supply and draining
hoses must be securely fastened and
remain undamaged.
NOTICE
Open the taps completely after
making the connections to check for water
leaks.
Aquasafe+Aquasafe
(depends on the model)
The Aquasafe+Aquasafe system protects
against water leaks that may occur at the
hose inlet.Water contact with the valve box
of the system must be avoided to prevent
damage to the electrical system.
As the hose set contains electrical
connections and assemblies, never
shorten or lengthen the hose with
extension hoses.
If the Aquasafe+Aquasafe system is
damaged, unplug the product and call
the authorised service agent.
14/EN
Drain pipe must be connected to the
sewage system and it should not be
connected to any surface water.
Adjusting the feet
If the door of the product cannot be closed
properly or if the product rocks when you
push it slightly, then you need to adjust
the feet of the product. Adjust the feet of
the product as illustrated in the installation
Connection to the drain
Water discharge hose can directly be
connected to the drain hole or sink’s
drainage. See the installation manual
supplied with your machine for detailed
information.
min
300
min
120
max 1000
min 500
manual supplied with the product.
Steam may escape if the door of the
dishwasher is not adjusted properly.
Hot steam may cause serious burns
and injuries and damage your furniture.
Electrical connection
Connect the product to a grounded
outlet protected by a fuse complying
with the values in the "Technical
specifications" table. Our company
shall not be liable for any damages
that will arise when the product is used
without grounding in accordance with
the local regulations.
•Connection must comply with national
regulations.
•Power cable plug must be easily
accessible after installation.
•Plug in the product to a grounded
socket which is protected by a fuse of
10 Amperes.
•The specified voltage must be equal to
your mains voltage.
Do not make connections via extension
cables or multi-plugs.
Damaged power cables must be
replaced by the authorised service
agent.
15/EN
Preparation
Read “Safety Instructions” section first!
Tips for energy saving
Following information will help you use the
product in an ecological and energy-efficient
manner.
Wipe away any coarse food remnants on the
dishes before putting them in the product.
Manual pre-rinsing of tableware items
leads to increased water and energy
consumption and is not recommended.
Washing tableware in a household
dishwasher usually consumes less energy
and water in the use phase than hand
dishwashing when the household dishwasher
is used according to the manufacturer’s
instructions.
Operate the product after filling it completely.
When selecting a programme, consider
the table of "Programme data and average
consumption values" given on Quick Guide.
Do not put more detergent than suggested
on the detergent package.
Water softening system
The product is equipped with a water
softening system which reduces the
hardness of incoming water. This system
softens the supply water to a level that will
allow washing the dishes with the required
quality.
The mains water hardness must be
softened if it is over 7°dH. Otherwise,
hardness ions will accumulate on
the dishes that are washed and may
affect the washing, rinsing and drying
performances of the machine.
Adjusting the water softening
system
Washing performance will increase when
water softening system is adjusted properly.
5-
Read “Quick Guide - Adjusting Water
Softening System” before this section!
The regeneration of the water softening
system can be done in all programmes
during drying step. When regeneration
occurs, duration, energy and water
consumption of the programme increase.
For regeneration process; frequency of
regeneration cycle, maximum additional
duration, water and energy consumption
are given in table below depending on
Eco 50°C programme water consumption,
when the dishwasher is run under standard
conditions with 14 dH water supply on its
Eco 50°C programme:
Eco 50°C water
consumption (l)
Regeneration after
…. cycles
Additional
duration (min)
Additional water
consumption (l)
Additional energy
consumption (kWh)
12,3-14,7 5 5 3,0 0,05
9,6-12,2 6 5 3,0 0,05
9,0-9,5 7 5 3,0 0,05
8,0-9,0 8 5 3,0 0,05
7,0-7,9 9 5 3,0 0,05
For the water consumption of your
dishwasher on Eco 50°C programme,
look at the Programme data and average
consumption values table given on Quick
Guide.
16/EN
You can put about 2 kg of softening
salt into the salt reservoir.
5. Replace the lid and tighten it when the
reservoir is full.
You need to add salt right before
starting the machine. Thus, the
overflowing salty water will be flushed
immediately, preventing the risk
of corrosion in machine. In cases
where you would not start washing
immediately, run your machine empty
in the shortest programme.
Since different salt brands in the
market have different particle sizes and
since the water hardness may vary,
dissolution of the salt in water may
take a couple of hours. Therefore, Salt
Indicator remains on for a while after
adding salt into the machine.
Detergent
You can use powder, liquid/gel or tablet
detergents in the machine.
Only use detergents produced
particularly for use with dishwashers.
Note that detergents that contain
chlorine and phosphate can be harmful
for the environment. Liquid detergents
without chlorine may not remove tea
and coffee stains from cups.
Adding detergent
Pay attention to the warnings on the
detergent packaging to get better
washing and drying results. Contact
the manufacturer of the detergent for
Adding salt
Water softening system needs to be
regenerated in order for the product
to operate with the same performance
continuously. Dishwasher salt is used for
this purpose.
Use only special softening salts
produced particularly for the
dishwashers in your machine.
It is recommended to use granule- or
powder-formed softening salts in the
water softening system. Do not use
salts that do not completely dissolve
in water such as table salt or rock
salt. Otherwise the performance of the
system may deteriorate in time.
Salt reservoir will be filled with water
when you start the product. For this
reason, add salt before operating the
machine.
1. Firstly, take the lower basket out to add
softening salt.
2. Turn the salt reservoir lid counter-
clockwise to open it (A).
3. Add 1 liter of water to salt reservoir of
your machine only in initial use.
4. Fill the salt reservoir with salt by
using the salt funnel (D). To speed up
dissolution rate of salt in water, stir it
with a spoon.
17/EN
using detergent tablets.
3. Push the lid of the detergent dispenser
to close it. A "click" will be heard when
the lid is closed.
1
2
3
Use powder or liquid/gel detergent in
short programmes without prewash
since the solubility of the tablet
detergent changes depending on the
temperature and time.
further questions.
Do not put solvents into the detergent
dispenser. There is the risk of
explosion!
Put the detergent into the detergent
dispenser just before operating the
machine as illustrated below.
1. Push the latch to right to open the
detergent dispenser lid (A). (depends
on model)
2. Put suggested amount of powder,
liquid/gel or tablet detergent in the
reservoir.
Inside the detergent dispenser there
are level markings that help you
use appropriate amount of powder
detergent. When brimful, detergent
dispenser will contain 45 cm³ of
detergent. Fill detergent up to 15 cm³
or 25 cm³ level marks in the detergent
dispenser according to fullness of the
machine and/or soiling degree of the
dishes. One tablet is enough if you are
18/EN
3. After the empty washing cycle, review
the user manual and readjust the water
hardness level so as to suit the water
supply.
4. Make the appropriate rinse aid settings.
Rinse aid
The rinse aid used in dishwashers
is a special combination that aims to
increase drying efficiency and prevent
water or lime stains on the washed
items. For this reason, care must be
paid to have rinse aid in the rinse
aid reservoir and to use rinse aids
produced specially for dishwashers
only.
1. Open the lid of the rinse aid reservoir
with the help of the latch.
2. Fill the reservoir until “MAX” level.
Tablet detergents
In addition to the conventional tablet
detergents, there are also commercially
available detergent tablets that show water
softening salt and/or rinse aid effect. Some
types of these detergents contain special-
purpose components such as glass and
stainless steel protectors. These tablets
show their effects up to a certain water
hardness level (21°dH). Water softening
salt and rinse aid must also be used
together with the detergent if the water
hardness level is above the mentioned
level.
The best washing performance in
dishwashers is obtained by using
detergent, rinse aid and water
softening salt individually.
Observe the instructions of the
detergent manufacturer on the package
when using tablet detergents.
Contact the detergent manufacturer if
your dishes are wet and/or if you notice
limescale spots particularly on your
glasses after the washing programme
is over when using a tablet detergent.
When you switch to powder
detergent from tablet detergent:
1. Make sure that salt and rinse aid
reservoirs are full.
2. Set the water hardness to the highest
level and perform an empty run.
19/EN
3. Slightly press the point (B) of the
reservoir lid to close it.
4. If there are stains on tableware items
after washing, level must be increased
and if there is a blue trace after wiping
them by hand, it must be decreased.
This is set to position 3 as factory
default.
The rinse aid adjustment is described
under "Adjusting the amount of rinse
aid" in the section for operating the
machine.
Wipe clean any spilled rinse aid
outside the reservoir. Rinse aid that
spilled accidentally will cause foaming
and it will eventually decrease washing
performance.
Items not suitable for washing in
the dishwasher
•Never wash dishes soiled by cigarette
ash, candle remnants, polish, dyestuff,
chemicals, etc. in your dishwasher.
•Do not wash silverware and cutlery
with wooden or bone stems, glued
pieces, or pieces that are not resistant
to heat, as well as copper and tin-
plated containers in the dishwasher.
Decorative prints of chinaware as well
as aluminium and silver items may get
discoloured or tarnished after washing
in the dishwasher just as it happens in
handwashing as well. Some delicate
glass types and crystals may become
dull in time. We strongly recommend
you to check if the tableware you
are going to purchase is suitable for
washing especially in the dishwasher.
Placing the dishes into the
dishwasher
Depending on the capacity of your
dishwasher, you can use your dishwasher
in the optimum way with respect to energy
consumption and washing and drying
performance only if you place the dishes in
an orderly way.
•Wipe away any coarse food remnants
(bones, seeds, etc.) on the dishes
before placing them in the dishwasher.
•Place thin, narrow pieces in the middle
sections of baskets if possible.
•Place the heavily soiled and bigger
items in the lower basket and smaller,
delicate and light items in the upper
basket.
•Place the hollowed dishes such as
bowls, glasses and pans upside down
in the dishwasher. Thus, accumulation
of water in deep hollows is prevented.
To prevent possible injuries, always
place the sharp and pointed dishes
such as service fork, bread knife, etc.
upside down so as their pointed ends
will face down or lay them horizontally
in the dish basket.
Unload dishes in the lower basket first and
then the dishes in the upper basket.
20/EN
Suggestions for loading the dishwasher
Lower basket
Upper basket
Improper Loading Of Dishware
Improper Loading Of Dishware
21/EN
Cutlery basket
(depends on model)
Cutlery basket is designed to wash your
dishes such as knife, fork, spoon, etc. in an
efficient manner.
Since the cutlery basket can be moved
(A, B), you can create more space while
placing your dishes in the lower basket and
free up space for your dishes of different
sizes.
Cutlery basket
(depends on model)
Cutlery basket is designed to wash your
dishes such as knife, fork, spoon, etc. in an
efficient manner.
Since the cutlery basket can be moved
(A, B), you can create more space while
placing your dishes in the lower basket and
free up space for your dishes of different
sizes..
22/EN
Collapsible lower basket tines
(depends on model)
There are foldable tines (A) located at
the lower basket of the machine are
designed for an easier placement of large
pieces such as pans, bowls, etc. You can
create larger spaces by folding each tines
individually or all of them at once.
To bring the collapsible tines into horizontal
position, grab the tines from mid position
and push them in the directions of arrows
(B). To bring the tines back to vertical
position, just lift them up. Collapsible tines
will click into the latch again (C).
Bringing the tines to the horizontal
position by holding them from the tips
may cause them to bend. Therefore,
it will be appropriate to bring the tines
in the middle to horizontal or vertical
position by holding them from their
stems and pushing in the direction of
arrow.
Collapsible lower basket tines
(depends on model)
There are foldable tines (A) located at
the lower basket of the machine are
designed for an easier placement of large
pieces such as pans, bowls, etc. You can
create larger spaces by folding each tines
individually or all of them at once.
To bring the collapsible tines into horizontal
position, grab the tines from mid position
and push them in the directions of arrows
(B). To bring the tines back to vertical
position, just lift them up. Collapsible tines
will click into the latch again (C).
Bringing the tines to the horizontal
position by holding them from the tips
may cause them to bend. Therefore,
it will be appropriate to bring the tines
in the middle to horizontal or vertical
position by holding them from their
stems and pushing in the direction of
arrow.
23/EN
Tray Wash Supports
(depends on model)
Use the supports to wash trays in the
bottom basket.
See the Auxiliary functions section for
appropriate programme and function
selection.
SoftTouch Accessory
(depends on model)
The SoftTouch Accessory found in the
lower basket of your machine enables a
safe washing for your fragile glasses.
Lower Basket Glass Holder
(depends on model)
Lower Basket Glass Holder found in the
lower basket of your machine enables a
safe washing for your oversized and tall
glasses.
24/EN
Lower basket multipurpose /
height adjustable service rack
(depends on model)
This accessory located at the lower basket
of your machine allows you to easily wash
pieces such as extra glasses, long ladles
and bread knives.
You may use the racks as required by
moving them to lower or upper position,
or close them to create a wider space
in your lower basket.
Make sure that the impeller does not
touch the dishes you placed on the
racks.
To close the racks:
1. Fold the rack (A).
2. Slide the rack up (B).
3. Put the rack in vertical position (C).
4. Slide the rack down and lock it by the
tabs (D).
You may open the racks in the same
process in reverse order.
To adjust the height of the racks:
1. Fold the rack (E).
2. Slide the rack up (F).
3. Open the rack at the desired level (G).
25/EN
Upper basket multipurpose
service rack
(depends on model)
This accessory located at the upper basket
of your machine allows you to easily wash
pieces such as extra long ladles and bread
knives.
You can lift up the upper basket
multipurpose service rack to remove it if
you do not want to use it.
If you want to use the upper basket
multipurpose service rack again, you can
easily attach it to the side section of your
upper basket.
Upper basket height adjustable
rack
(depends on model)
Use the lower and upper parts of the height
adjustable racks in the upper basket of
the machine by sliding them down or up
according to the heights of the glasses,
cups or etc. (A, B, C).
Lower basket bottle wire
(depends on model)
The bottle wire is designed for easier
washing of long pieces with wide mouths.
You may take out the bottle wire from the
basket when not in use by pulling it out
from both sides (H).
26/EN
Upper basket multi-function
service rack
(depends on model)
Thanks to the upper basket multi-function
service rack on the upper basket of your
appliance, you may load and wash long
service-ware and kitchen-ware easily. Also,
the wineglass securing compartments
available on the front side of this accessory
allows easier placing of the stemware with
proper sizes on the upper basket.
You may remove the upper basket multi-
function service rack by lifting it upwards
when you do not want to use it.
You may reinstall the upper basket multi-
function service rack on the side of your
upper basket easily to use it again.
Tray Washing Support
(depends on model)
You may use the tray washing supports
if you want to wash a tray on your lower
basket.
Refer to the Additional Functions section to
select the proper program and function.
You may fold this part when it is not used to
facilitate the placement of your dishes.
12
You may also remove the part when
required as shown in figures 1 and 2.
The tray washing supports shall be
removed as shown in figures 1 and
2 for performance inspection tests
that shall be performed as per the
standards.
27/EN
To lower the basket, while it is in the
uppermost position;
1. Hold the upper basket wires with both
hands, slightly lift up the basket and
simultaneously push and release the
latches shown in the figure (B).
2. Lower the basket from its current
position to the lower one.
3. Release the basket after it has reached
one level down.
Repeat the process if the height is not
sufficient.
1
2
3
The movement mechanism may not
function properly if the upper basket is
overloaded or if the weight distribution
is not balanced. In heavier conditions,
there is the risk of falling one level
down.
Make sure that the adjustment
mechanism has the same positions
on the right and left sides of the upper
basket.
Adjusting the height of the upper
basket
(depends on model)
The upper basket height adjustment
mechanism has been designed for you to
create large spaces in the lower or upper
sections of your machine depending on
your needs by adjusting the height in the
upper or lower direction while your basket
is empty or loaded.
Thanks to this mechanism, you can use
your basket in three different positions,
namely lower, middle and upper positions
(1, 2, 3).
1. To raise your basket, hold the upper
basket wires with both hands while the
basket is in the lowermost position and
pull them up (A).
2. You will hear a "Click" from the right
and left mechanisms, indicating that
the basket has reached the next level.
Release the basket.
Repeat the process if the height is not
sufficient.
1
2
3
28/EN
Adjusting the height of the upper
basket
(depends on model)
Upper basket height adjustment
mechanism is designed so that you can
create wide spaces on the upper or lower
compartment of the machine by adjusting
the basket upwards or downwards either
while it is empty or full.
Thanks to this mechanism, you may use
your basket in three different positions,
namely lower, center or upper positions.
To lower the basket, perform the following
while the basket is at uppermost position;
1. Hold the wires of the upper basket and
raise the handle of the mechanism
upwards as shown in the figure (A).
2. Lower the basket to the next lower
position.
3. Release the basket when it catches on
to the next lower position.
Repeat the same operation if the height is
not adequate.
1
2
3
1. To raise the basket, hold the wires of
the basket and pull the basket upwards
with both hands while the basket is at
the lowermost position (B)
2. Release the basket when it catches on
to the next upper position with a “Click”
that may be heard from the right and
left mechanisms.
Repeat the same operation if the height is
not adequate.
1
2
3
The movement mechanism may not
work properly when the upper basket is
overloaded or when the load is
unbalanced. And it may fall to the next
lower position in heavier conditions.
Ensure that the adjustment
mechanisms on the right and left of the
upper basket are aligned.
29/EN
Height setting with empty basket
(depends on model)
In this model, the height setting of the
upper basket may be changed using the
wheels which are mounted at two different
heights.
Release the latches on both the right and
left tracks of the upper basket by pushing
them outwards.
Pull the basket out completely.
Place the basket back into the tracks at the
desired height.
Push the latches back into the correct
position.
Collapsible upper basket wires
(depends on model)
You can use collapsible wires when you
need a larger space for your dishes in the
upper basket of your machine.
To bring the collapsible wires into horizontal
position, grab the wire from the middle
position and push them in the direction of
arrow in the figure. Place your larger dishes
into the area created. To bring the wires
back to vertical position, just lift them up.
Bringing the wires to the horizontal
position by holding them from the tips
may cause them to bend. Therefore,
hold the wires from their stems while
bringing them to the horizontal or
vertical positions.
30/EN
Ceiling cutlery basket
(depends on model)
Ceiling cutlery basket is designed to wash
your cutlery items such as forks, spoons
and etc. by placing them between the bars
on the basket.
Ceiling cutlery basket
(depends on model)
Ceiling cutlery basket is designed to wash
your cutlery items such as forks, spoons
and etc. by placing them between the bars
on the basket.
1
In models with partial movement feature,
pushing the bar (1) on the handle enables
the central tray of the basket to get to
the lower position and the system gets
unlocked. Thus right and left side trays can
be used as moving parts.
The free space enabled by the side trays
allows long parts to be loaded in the upper
basket.
When the central tray is in the lower
position, you can load long/high items
such as coffee cups, ladles, etc. on the
tray. When the side trays lean on two side
walls, the handle can be pulled to allow the
central tray to rise and the system to be
locked.
31/EN
Operating the product
6-
On/Off key
When you press the On/Off key, the
product that is in the On position will switch
on with the Eco programme.
Programme Selection /
Programme Cancel key
Select the programme by pressing the
desired programme key.
Press the Start / Pause / Cancel key for 3
seconds to cancel the running programme.
Function Keys
If you press any of the Function keys
during programme selection or time delay
selection, the indicator of the function will
flash if the programme you have selected
supports the selected function.
To cancel the selected function, press the
function key again.
Preparing the machine
1. Open the door of the dishwasher.
2. Place the dishes in accordance with
the instructions in the user manual.
3. Make sure that the upper and lower
impellers rotate freely.
4. Put adequate amount of detergent into
the detergent dispenser.
5. Check if the Salt and Rinse Aid
indicators light and add salt and/or
rinse aid if needed.
Programme selection
1. Press the On/Off button to turn on your
machine.
Auxiliary functions
Washing programmes of your dishwasher
are designed to obtain the best cleaning
effect, considering the type of the soiling,
soiling degree and properties of the dishes
to be washed.
Auxiliary functions allow you save from
time, water and power.
Auxiliary functions may cause changes
in the programme duration.
Auxiliary functions are not suitable for
all washing programs. Indicator of the
auxiliary function that is not compatible
with the programme will not be active.
2. Refer to the table of "Programme data
and average consumption values"
to determine a washing programme
suitable for your dishes.
3. Selected programme will start when
you close the door of your machine.
Read “Safety Instructions” section first!
Read “Quick Quide” before this
section.
Half Load function
(Depends on model)
It is used to operate the machine without
loading it completely.
1. Load your dishes in the machine as
you like.
2. Turn the machine on with On/Off key.
3. Select the desired programme and
press the Half Load key.
While the function is enabled, the Half
Load indicator will come on in the function
selection indicator and on the display.
4. Close the door of the machine to start
the programme.
With the Half Load function you can
save both water and power while using
the lower and upper baskets of the
machine.
32/EN
Half Load function/
AquaIntense Function
(depends on model)
AquaIntense impeller
located under the
lower impeller helps
washing your heavily
soiled dishes placed
in the right side of the lower basket. It will
give better results to place the most soiled
dish to the right front side.
Do not try to remove the AquaIntense
impeller!
Fast+ Function
(Depends on model)
It shortens the time of the washing cycle
selected and decreases water consumption
by enabling washing under higher pressure.
SteamGloss Function
(Depends on model)
It provides superior drying performance.
Tablet detergent function
(depends on model)
Allows to obtain a better drying
performance from the multi-purpose
detergents called as all in one detergents
such as 2in1, 3in1, 4in1, 5in1 and etc.,
depending on the hardness level of the tap
water.
Press and hold the tablet function buttons
on the panel to activate the tablet function
for appropriate programmes. Selecting the
tablet function will light the Tablet Detergent
indicator.
If you have used the Tablet features
during the last washing programme
you used, Tablet function will remain
active in the next washing programme
you will select. If you do not want to
use these functions in the new program
you have selected, press the Tablet
Detergent key until the indicator of the
relevant function turns off.
Tablet Detergent function may cause
change in the programme duration.
TrayWash Function
(depends on the model)
Select Intensive 70°C programme and
press function key to run this function.
AquaActive Function
(Depends on model)
This function operates the lower impeller
with a higher pressure and higher speed to
enable a better washing for dishes such as
pans and trays with stubborn, dried soiling.
IonGuard function
(depends on the model)
IonGuard function is enabled at regular
intervals and prevents the formation of
bad odours due to putrefaction. If this
function is selected, it will be activated
while the product is turned off and the
IonGuard indicator on the panel will flash.
A ventilation noise can be heard, this
is normal. Until the function selection is
disabled, system is automatically activated
intermittently.
Super Rinse Function
(Depends on model)
Depending on the type of the detergent
used, if a detergent dissolving issue is
encountered it will remove the resulting
stains from the dishes and enables the
optimum rinsing performance.
Hygiene Intense function
(depends on the model)
Designed to be used when more hygiene
is required for washing the dishes. This
function increases the washing and rinsing
temperatures in the selected cycle and
extends the periods of these steps in the
cycle. Moreover, an additional rinsing cycle
is performed to wash and rinse your dishes
with more hygiene.
33/EN
Changing Warning Sound Volume
1. After turning on your machine, press
and hold the Time Delay and Start /
Pause / Cancel keys respectively.
2. Using the Time Delay key, turn on 9
and 6 LEDs.
3. Adjust the volume with the function
keys.
If the 1st programme indicator is on, the
volume is off
If the 2nd programme indicator is on, the
volume is at medium level
If the 3rd programme indicator is on, the
volume is at high level.
4. Turn off the machine with the On/Off
key to save the changes.
Floor illumination
Warning to show that machine is in
washing phase
(depends on the model)
Your machine reflects a light to the floor
during the washing process. This light turns
off after the washing process is complete.
Floor illumination is activated
automatically when the washing
programme starts and remains lit until
the end of the programme.
Floor illumination cannot be cancelled
by the user.
Inner Illumination
(depends on the model)
Some models have interior lighting to
illuminate the interior when the door is
opened.
Changing the interior lighting
setting
1. After turning on your machine, press
and hold the Time Delay and Start /
Pause / Cancel key for 3 seconds.
2. Press the Time Delay key to switch the
delay indicator to position 9.
3. You can press the function keys to
turn on and off the inner illumination.
The inner illumination is switched to
off position if the 1st programme LED
is on, and to the on position if the 2nd
programme LED is on.
4. Press the On/Off key to exit the
settings menu. Your setting will be
saved automatically.
SelfDry
(Depends on the Model)
Thanks to the “SelfDry” feature on your
machine, the drying effectiveness of your
machine is improved and power is saved.
There are two options, namely “OFF” and
“ON”.
You may use sub-menu settings to change
“SelfDry” settings.
When you activate this function, the door
of your machine is opened automatically at
the end of the washing cycle.
SelfDry feature opens the door at
the end of the washing cycle thanks
to the “door opening shafts". This
process takes about 2 minutes. Do not
force to close the door if the power is
interrupted while the shafts are moving
out. Operation shall be completed
and shafts shall be retracted when the
power is restored.
SelfDry function may cause changes to
the cycle time.
34/EN
Changing SelfDry Settings
1. Press the Delay and Start/Pause/
Cancel key simultaneously for 3
seconds after turning on your machine.
2. Press the Delay key until 3 hours delay
indicator is illuminated in the menu.
Using the function keys, set the SelfDry
function on or off. Function is off when
the first cycle indicator is illuminated,
and it is turned on when the second
cycle indicator is illuminated.
3. Turn off your machine with the On/Off
key to save the setting.
EverClean Filter
(depends on the model)
With this function, your micro filter will be
cleaned by a special system at the end of
washing cycle and it is made ready for use
for the next usage of the machine. This
cleaning process increases the cleaning
period of the micro filter from 2 weeks to
3 months and thus boosts the washing
performance. Employing this function in
every washing cycle is recommended in
order to get the most out of it.
Programming the washing time
Time Delay
If an economical electricity tariff is applied
in your region, you can use the time
delay function to wash your dishes during
appropriate hours.
You can delay the start of the selected
programme up to 9 hours.
Hold the delayed start key pressed for
1 second more than the other keys.
1. Press the time delay key after selecting
the washing programme and other
auxiliary functions.
2. Once you press the Time Delay key "3
hours" Time Delay indicator will start
flashing.
3. Set the desired time by pressing the
Time Delay key. Each press on the key
will increase up to 9 hours with 3-hour
increments.
4. Close the door of your machine after
setting the Time Delay. Once the delay
time is over, the selected programme
will start automatically.
The time delay will start countdown
with the closing of the door after
selecting the Time Delay function.
If the door is opened while the Time
Delay function is active, the countdown
will be paused and start icon will start
to flash.
Changing the settings while Time
Delay function is active
While the Time Delay function is activated,
you cannot make changes in the washing
programme, auxiliary functions or the
duration of time delay.
Auxiliary functions cannot be set after
the programme has started.
To cancel the time delay function
To cancel the process while the Time Delay
function is active the programme should be
canceled.
35/EN
Time delay function cannot be set after
the programme has started.
Starting the programme
Close the door of your machine to start it
after selecting the programme and auxiliary
functions.
Your machine performs water softening
depending on the hardness level of the
mains water. Washing time can change
while the programme is running
depending on the ambient temperature
where your machine is installed,
temperature of the supply water and
amount of the dishes.
Pay attention not to open the door of
the machine when it is running. There
may be a rush of vapour when you
open the door of your machine; be
careful.
After the rinsing step the machine
will wait silent in pause mode for
some time in order to have the water
remaining in the machine and on the
dishes drained completely and to have
the water softener cleaned, and then it
will resume running in drying mode.
Cancelling the programme
Press and hold the Programme Selection
/ Programme Cancel keys for 3 seconds.
Release the key as the Start indicator starts
flashing.
Once you close the door of your machine,
draining is completed in 2 minutes
and the machine gives an audible warning
when it is completed.
There might be residues of detergent
or rinse aid left in the machine and/or
on the pieces being washed depending
on the step in which the programme
has been cancelled.
Salt Indicator ( )
Please check the salt indicator on the
display to see whether there is adequate
amount of softening salt in the dishwasher
or not. You need to refill the salt reservoir
with salt whenever salt indicator appears
on the display of your machine.
Adjusting the water hardness level is
explained in Water Softening System
section.
Rinse Aid Indicator ( )
Please check the rinse aid indicator on the
display to see whether there is adequate
amount of rinse aid in the dishwasher or
not. You need to refill the rinse aid reservoir
with rinse aid whenever rinse aid indicator
appears on the display of your machine.
Adjusting the amount of rinse
aid
1. After turning on your machine, press
and hold the Time Delay and Start /
Pause / Cancel keys respectively.
2. Using the Time Delay key, turn on the 6
LED.
3. You can use the function keys to adjust
the rinse aid level.
If the 1st programme indicator is on, no
rinse aid will be dispensed
If the 2nd programme indicator is on, 1
dose of rinse aid will be dispensed.
If the 3rd programme indicator is on, 2
doses of rinse aid will be dispensed.
If the 4th programme indicator is on, 3
doses of rinse aid will be dispensed.
If the 1st, 2nd, 3rd and 4th programme
indicators are on, 4 doses of rinse aid will
be dispensed.
4. Press the On/Off key to exit the
settings menu. Your setting will be
saved automatically.
36/EN
End of programme
When the programme you have
selected comes to an end, an audible
warning signal will warn you to turn off
your machine. This audible signal will
warn you with certain intervals before it
turns off.
Start / Pause indicator will go off once the
washing programme has ended.
1. Open the door of the machine.
2. Press the On/Off key to switch off your
machine.
3. Close the tap.
4. Unplug the machine from the socket.
For energy saving, the machine is
automatically switched off following the
completion of the programme or when
the programme is not started.
Leave your dishes in the machine
for about 15 minutes after they are
washed in order to have them cooled.
Your dishes will dry in a shorter time
if you leave the door of your machine
ajar during this period. This process
will increase the drying effectiveness of
your machine.
Water Cut-off Warning
If mains water is cut off or water inlet tap
is turned off, the machine will not take
water in and water off indicator will flash.
As long as the problem continues, washing
programme is paused and the water inlet
is checked regularly by the machine; when
the water is restored water off indicator will
disappear after a while and the washing
programme resumes.
Overflowing Warning
If the machine intakes too much water or
there is leakage at any of the components
then the machine will detect this and
water overflow indicator will flash on the
Programme indicator. As long as the
overflowing continues the safety algorithm
will be active and try to discharge the water.
If overflowing stops and safety is assured,
water overflow indicator will disappear. If
the indicator does not disappear, there is a
permanent fault. In this case the authorised
service should be contacted.
InnerClean
(depends on model)
This programme is recommended to be
operated on each 1-2 months for machine
cleaning and necessary hygiene. The
programme should be operated while the
machine is empty.
In order to achieve an efficient result, it is
recommended to use together with special
machine cleaning agents.
Do not use this programme to
clean dishes. As it operates in high
temperatures, it is harmful for the
dishes.
37/EN
Maintenance and
cleaning
Read “Safety Instructions” section first!
Unplug the product and turn off the
tap before attempting any cleaning
procedures.
Do not use abrasive substances for
cleaning.
Clean the filter and impellers at least
once a week in order for the machine to
operate efficiently.
Service life of the product extends and
frequently faced problems decrease if it is
cleaned at regular intervals.
Cleaning the outer surface of the
product
NOTICE
Clean the outer surface and door
gaskets of the product gently with a mild
cleaning material and damp cloth. Wipe the
“control panel” only with a damp cloth.
Cleaning the interior of the
machine
•Clean the interior of the machine by
operating the machine in the programme
running at the highest possible
temperature with detergent or special
machine cleaning agents monthly. This
operation will help removal of leftovers
and limescale from the interior of the
machine.
•If water has remained in the machine,
drain the water by performing the
procedures under the topic "Cancelling
a programme". If the water cannot
be discharged, remove the filters as
specified in the "Cleaning the filters"
section and check if there are any
leftover deposits that have accumulated
at the bottom of the machine, blocking
the water path. Clean if necessary.
Cleaning the filters
Clean the filters at least once a week in
order for the machine operates efficiently.
Check if food residues are left on the filters.
If there are food residues on filters, take
them out and clean well under running
water.
1. Turn the micro filter (1) and coarse filter
(2) assembly counter clockwise and
pull it out from its seating.(depends on
model)
2. Pull out the metal/plastic filter (3) from
the seating.
3. Press the two pawls on the coarse filter
inwards and separate the coarse filter
from the assembly.
7-
38/EN
4. Clean all three filters under tap water
by means of a brush.
5. Place the metal/plastic filter.
6. Place the coarse filter into the micro
filter. Make sure that it is properly
seated. Turn the coarse filter clockwise
until a "click" sound is heard.
Do not use the dishwasher without
filter.
Incorrect placement of the filters will
reduce washing efficiency.
Micro Filter Cleaning Mechanism
(depends on model)
Filter cleanliness is increased by 80%
with the micro filter cleaning system
available on your machine.
If your machine has auto filter cleaning
feature do not remove the micro filter
cleaning mechanism (4) for cleaning.
Cleaning the hose filter
Damages on the machine that may be
caused by impurities coming from the
urban supply water or your own water
installation (such as sand, dirt, rust, etc.)
can be prevented by means of the filter
attached to the water inlet hose. Check the
filter and the hose regularly and clean them
if necessary.
1. Turn off the tap and remove the hose.
2. After taking out the filter, clean it under
running tap water.
3. Place the cleaned filter back to its seat
in the hose.
4. Install the hose to tap.
(depends on model)
39/EN
Cleaning the impellers
Clean the impellers at least once a week in
order for the machine operates efficiently.
Lower impeller
Check if the holes on the lower impeller (1)
are clogged. If they are clogged, remove
and clean the impeller. You can pull the
lower impeller up to remove it.
(depends on model)
Check if the holes on the lower impeller
assembly are clogged. If they are clogged,
remove and clean the impeller assembly.
(depends on model)
C
To remove and clean the lower impeller
assembly together, hold by one hand from
the (C) points shown in the figure and pull
up to remove. After cleaning, follow these
steps in reverse order to reinstall the
impeller assembly.
Do not try to rotate the impeller by
holding its ends. Trying to rotate the
end sections may cause the gear
system within the impeller to break.
Upper impeller
Check if the holes on the upper impeller (1)
are clogged. If they are clogged, remove
and clean the impeller. Turn its nut to left to
remove the upper impeller.
Make sure that the nut is tightened well
when installing the upper impeller.
40/EN
Troubleshooting
Machine does not start.
• Power cable is unplugged. >>> Check if the power cable is plugged in.
• Fuse is blown. >>> Check the fuses in your house.
• Water is cut. >>> Make sure that the water inlet tap is open.
• Door of the machine is open. >>> Make sure that you have closed the door of the
machine.
• On / Off button is not pressed. >>> Make sure that you have turned on the machine by
pressing the On / Off button.
Dishes are not washed clean
• Dishes are not placed orderly in the machine. >>> Load the dishes as described in the
user manual.
• Selected programme is unsuitable. >>> Select a programme with a higher temperature
and cycle time.
• Impellers are stuck. >>> Prior to starting the programme, turn the lower and upper
impellers by hand to make sure that they rotate freely.
• Impeller holes are clogged. >>> Lower and upper impeller holes might be clogged
with food remnants such as lemon pips. Clean the impellers regularly as illustrated in
section “Cleaning and Care”.
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter system
regularly as illustrated in section “Cleaning and Care”.
• Filters are installed incorrectly. >>> Check the filter system and make sure that it is
installed correctly.
• Baskets are overloaded. >>> Do not overload the baskets in excess of their capacity.
• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a closed
container if possible. For ease-of-storing, we recommend you to use tablet detergents.
• Detergent is not sufficient. >>> If you are using powder detergent, adjust the amount of
detergent according to the soiling degree of your dishes and/or programme definitions.
We recommend you to use tablet detergents for optimum results.
• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if
necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the
machine.
• Detergent dispenser lid is left open. >>> Make sure that the detergent dispenser lid is
closed tightly after adding detergent.
Dishes are not dry at the end of cycle
• Dishes are not placed orderly in the machine. >>> Place your dishes in a way that no
water will accumulate in them.
8-
41/EN
• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if
necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the
machine.
• Machine is unloaded right after the programme is over. >>> Do not unload your
machine right after washing process is completed. Slightly open the door and wait
for evacuation of the steam inside for a while. Unload the dishes after the pieces
cool down to a touchable level. Start unloading process from the lower basket. Thus,
dropping of water remained on a piece at upper basket onto the pieces at lower basket
is prevented.
• Selected programme is unsuitable. >>> Since rinsing temperature is low at
programmes with short duration, drying performance will also be low. Select
programmes with longer duration for a higher drying performance.
• Surface quality of the kitchen utensils is deteriorated. >>> Desired washing
performance can not be obtained on kitchen utensils with deteriorated surfaces and it
is not suitable to use such utensils in terms of hygiene as well. Also, water can not flow
easily on deteriorated surfaces. It is not recommended to wash such kitchen utensils in
dishwasher.
It is normal that drying complaints can be experienced with Teflon kitchen utensils. It is
associated with the structure of Teflon. Since the surface tensions of Teflon and water
are different, water droplets will remain as beads on the Teflon surface.
Tea, coffee or lipstick stains remain on dishes.
• Selected programme is unsuitable. >>> Select a programme with a higher temperature
and cycle time.
• Surface quality of the kitchen utensils is deteriorated. >>> Tea and coffee stains or
other dye spots may not be cleaned in dishwasher when they have penetrated in
deteriorated surfaces. Desired washing performance can not be obtained on kitchen
utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of
hygiene as well. It is not recommended to wash such kitchen utensils in dishwasher.
• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a closed
container if possible. For ease-of-storing, we recommend you to use tablet detergents.
Lime traces remain on dishes and glassware gains a misty appearance
• Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if
necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the
machine.
• Water hardness setting is low or salt level is insufficient >>> Measure the hardness of
the supply water appropriately and check the water hardness setting.
• Salt leakage exists. >>> Pay attention not to spill salt around the salt filling hole while
adding salt. Make sure that the salt reservoir lid is tightly closed after finishing the
filling process. Run the prewash programme to remove the salt that spilled inside
the machine. Since the salt granules that will remain under the lid will dissolve
during prewash, causing the lid loosen, check the lid once again at the end of the
programme.
42/EN
There is a different odour in the machine
A new machine has a peculiar odour. It will fade out after a couple of washes.
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter system
regularly as illustrated in section “Cleaning and Care”.
• Dirty dishes are kept in dishwasher for 2-3 days. >>> If you are not going to start
the machine right after you have put the dishes into it, remove the remnants on the
dishes and run the Prewash programme without detergent every 2 days. In such
cases, do not close the door of the machine completely in order to avoid odour build
up in machine. You can also use commercially available odour removers or machine
cleaners.
Rust, discoloration or surface deterioration occurs on dishes
• Salt leakage exists. >>> Salt may cause deterioration and oxidation on metal surfaces.
Pay attention not to spill salt around the salt filling hole while adding salt. Make sure
that the salt reservoir lid is tightly closed after finishing the filling process. Run the
prewash programme to remove the salt that spilled inside the machine. Since the salt
granules that will remain under the lid will dissolve during prewash, causing the lid
loosen, check the lid once again at the end of the programme.
• Salty food remnants have remained on dishes for a long time. >>> If cutlery soiled
with such foods will be kept waiting in machine, dirt must be removed by prewash or
dishes must be washed without being kept waiting.
• Electric installation is not grounded. >>>Check if your machine is connected to the
actual grounding line. Otherwise, the static electric created in the product causes arcs
on the surfaces of metal items creating pores, removing the protective cover on the
surface and causing discoloration.
• Intensive cleansers such as bleaches are used. >>> Protective cover on metal
surfaces gets damaged and looses its efficiency in time when it gets in contact with
cleansers such as bleach. Do not wash your dishes with bleach.
• Metal items particularly knives are used for purposes other then their intended uses.
>>> Protective cover on the edges of knives may get damaged when they are used for
purposes such as opening cans. Do not use metal kitchen utensils out of their intended
uses.
• Cutlery are made of low quality stainless steel. >>> Corrosion on such items is
inevitable; they should not be washed in dishwashers.
• Kitchen utensils that are already corroded are washed in dishwasher. >>> Rust on a
corroded item can migrate to other stainless steel surfaces and cause corrosion on
those surfaces as well. Such items should not be washed in dishwashers.
Detergent remains in detergent dispenser.
• Detergent dispenser was damp when adding detergent. >>> Make sure that the
detergent dispenser is dried well prior to filling it with detergent.
• Detergent is added long before the washing process. >>> Pay attention to add
detergent shortly before start-up of the washing.
43/EN
• Opening of the detergent dispenser lid is prevented during washing. >>> Place the
dishes in a way that will not prevent the detergent dispenser lid from opening and the
water going into the machine from impellers.
• Detergent is stored under unsuitable conditions. >>> If you are using powder
detergent, do not store the detergent package in humid places. Keep it in a closed
container if possible. For ease-of-storing, we recommend you to use tablet detergents.
• Impeller holes are clogged. >>> Lower and upper impeller holes might be clogged
with food remnants such as lemon pips. Clean the impellers regularly as illustrated in
section “Cleaning and Care”.
Decorations and ornaments on kitchen utensils are being erased.
Decorated glasses and decorated lustre porcelains are not suitable for washing in the
dishwasher. Manufacturers of some glassware and porcelain tableware items do not
recommend washing such kitchen utensils in the dishwashers either.
Dishes are scratched.
Kitchen utensils that contains or are made of aluminium should not be washed in
dishwasher.
• Salt leakage exists. >>> Pay attention not to spill salt around the salt filling hole while
adding salt. Spilled salt can cause scratches. Make sure that the salt reservoir lid is
tightly closed after finishing the filling process. Run the prewash programme to remove
the salt that spilled inside the machine. Since the salt granules that will remain under
the lid will dissolve during prewash, causing the lid loosen, check the lid once again at
the end of the programme.
• Water hardness setting is low or salt level is insufficient >>> Measure the hardness of
the supply water appropriately and check the water hardness setting.
• Dishes are not placed orderly in the machine. >>> When placing the glasses and other
glassware into the basket lean them not against other dishes but the edges or racks of
the basket or the glass support tines. Striking of the glasses to each other or to other
dishes due to the impact of water during washing can cause breaks, or scratches on
their surfaces.
A smear remains on glasses that resembles milk stain which can not be
removed when wiped by hand. A bluish / rainbow appearance occurs when
the glass is pointed to light.
• Excessive rinse aid is used. >>>Lower rinse aid setting. Clean the spilled rinse aid
when adding rinse aid.
• Corrosion has occurred on glass due to soft water. >>> Measure the hardness of the
supply water appropriately and check the water hardness setting. If your supply water
is soft (<5 dH), do not use salt. Choose programmes that wash in higher temperatures
(e.g. 60-65°C). You can also use glass protective detergents that are commercially
available.
44/EN
Foam forms in the machine.
• Dishes are washed with hand-wash detergent by hand but not rinsed before placing
them into the machine. >>> Hand-wash detergents do not contain antifoam. There is
no need to hand-wash the dishes before placing them into the machine. Removing the
coarse soil on the dishes under tap water, with a tissue paper or fork will be sufficient.
• Rinse aid has spilled into the machine when adding rinse aid. >>> Take care that rinse
aid is not spilled in the machine when you are filling it. Clean any spilled rinse ait with
the help of a tissue paper/towel.
• Lid of the rinse aid reservoir is left open. >>> Make sure that the lid of the rinse aid
reservoir is closed after adding rinse aid.
Kitchen utensils are broken.
• Dishes are not placed orderly in the machine. >>> Load the dishes as described in the
user manual.
• Baskets are overloaded. >>> Do not overload the baskets in excess of their capacity.
Water remains in the dishwasher at the end of the programme.
• Filters are clogged. >>> Check if the filter system is clean. Clean the filter system
regularly as illustrated in section “Cleaning and Care”.
• Discharge hose is clogged/blocked. >>> Check the discharge hose. If necessary,
remove the discharge hose, clear the blockage and insert is as illustrated in the user
manual.
If you cannot eliminate the problem although you follow the instructions in this section,
consult your dealer or the Authorised Service Agent. Never try to repair a nonfunctional
product yourself.