Beko BMF20B User Manual
Displayed below is the user manual for BMF20B by Beko which is a product in the Toaster Ovens category. This manual has pages.
Related Manuals
1
Sensitivity: Public
OVEN
SERVICE MANUAL
2
Sensitivity: Public
SAFETY WARNING
This section contains safety instructions that will help protect from risk of
personal injury or property damage.
Throughout this user manual the following symbols are used.
Important informations orinstructions of usage.
Warning for dangerous situations.
Warning for electric shock.
Warning for danger of fire.
Warning for hot surfaces.
General Safety
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
• Installation and repair procedures must always be performed by Authorized
Service Agents. The manufacturer shall not be held responsible for damages
arising from procedures carried out by unauthorized persons which may also void
the warranty. Before installation, read the instructions carefully.
• Do not operate the product if it is defective or has any visible damage.
Control that the product function knobs are switched off after every use.
Safety for Configurations
• Control the area of the configuration is appropriate.
• It is important that sources of energy is near the product.
• Do not lay the network wire on the hot surface.If not wire coalasces and this couses
short circuit.
• Be cafeful during the configuration wire is not cut or deformed.If not change them with
new one.
• There is not a component to release the gases resulting of the burning in the
product.Set up the product according to the configuration rules.Especially,be careful
with the airing tools and needs.
3
Sensitivity: Public
Informations for Consumer
• Product may be hot during the usage.Do not touch with hot parts ,inside the
oven,heating components etc. .When the product is working it is hot so do not put
combustable materials near the product.
• Do not wash the product with water! It is dangerous for electrick shock!Ürünü, üzerine s
• Do not heat the closed preserve jar or can with the product.Presure may cause the
explosion.
• Do not clean while the product is working.
• Do not change in anything on the porduct or any repair instead of some problems in the
user guide.
• If there is no door or window for airing ,blower must be built.
• Use a glove that is heat resistant during put/remove the meal to the hot oven
• Do not use the product if front glass is broken or removed or any deformation on the
tweel block.
• When tweel block is open, be careful about children do not sit down on it.
• Do not hang cloth or towel or something like them on handle.
4
Sensitivity: Public
PRODUCT ASSEMBLY/ ASSEMBLY RULES/ SETTINGS
Product Transportation
To carry or move the product, do
not use door or handle of the
product. Door, handle or hinges
can be harmed. Hold the sides of
the oven with both hands only
when it is cool to carry or move
the product.
When the product is being carried or
the product is being put to the ground,
do not put it keenly, do not drag it and
do not skid it from stairs.
5
Sensitivity: Public
Unpacking Product
To consider product changing in the mounting process, please do not harm package,
product and the product package when extracting.
① Remove the tape from the package.
② You should rise the oven and the foam with two hands
6
Sensitivity: Public
③ Take out the foam.
7
Sensitivity: Public
④ Take the plastic bag.
⑤The product should only be used on the bench.
8
Sensitivity: Public
Electrical Connection
Plug the power with the socket in good condition.
Oven Foots hang on (Optıonal)
There are four rubber feet as shown.
9
Sensitivity: Public
Product Use--Control panel
Turn the knob to set the desired function,cooking time, cooking temperature.
1
Thermostat knob
2
Function knob
3
Thermostat lamp
4
Mechanical timer
1
2
3
4
10
Sensitivity: Public
NOTE: Time must be set to start the cooking.If the time is not set, the oven will not work.
When the cooking time is over,
the time setting knob
automatically rotates
counterclockwise. (If you do not
want to use the timer function,
turn the knob clockwise or
counterclockwise to the hand
symbol).
Switch off the oven with the time
setting knob, function knob and
temperature knob.
11
Sensitivity: Public
Accessories
①Rotisserie Handle: Allow you to pick up Rotisserie fork.
②Rotisserie fork: Use to roast a variety of meats and poultry.
ROTISSERIE FORK USING TIPS
1. Insert the fork into the rod until near the end of the rod and then secure with thumbscrew.
2. Insert the food from the other side of the rod.
3. Place second fort into other side of the rod, and then secure with thumbscrew. Check that the
food is in the center of the rod firmly.
4. Insert the rod with food into the oven. Insert the one side of the rod into the support-hole of the
oven. And then place the other side of the rod onto the support-bracket of the oven.
③Wire Rack: For toasting, baking, and general cooking in casserole dishes and
standard pans.
④Food Tray: For use in broiling and roasting meat, poultry, fish, and various other foods.
⑤Food Tray Handle: for removing tray or rack.
⑥Crumb Tray: For collecting fallen oil or crumb.
12
Sensitivity: Public
Tags and Descriptions used in the product
Type the label
Given information on the product nameplate label on the product gas.
Sticker on the location;
According to the type of product,Located on the back wall of the product.
13
Sensitivity: Public
Barcode Label
According to the type of product,Located on the back wall of the product.
Barcode label location;
Product packaging is pasted on cardboard.
14
Sensitivity: Public
Operating functions
The order of operating modes shown here may be different from the arrangement on your
product.
Top and bottom heating
Fan supported bottom/top heating
Fan assisted top heating
Top and bottom heating are in
operation. Food is heated
simultaneously from the top and
bottom. For example, it is suitable for
cakes, pastries, or cakes and
casseroles in baking moulds. Cook
with one tray only.
Top heating, bottom heating plus fan
(in the rear wall) are in operation. Hot
air is evenly distributed throughout
the oven rapidly by means of the fan.
Cook with one tray only.
Top heating and the fan (in the rear
wall) are in operation. Hot air is
distributed better with fan when
compared to the situation where only
top heating is in operation.
15
Sensitivity: Public
Top/ bottom heating
/
Top+ bottom heating + convection + rotisserie
This function is ideal for
baking pork slice, chicken
legs, chicken wings, potato
flakes, poultry meat, chops,
fish and so on with more
evenly heating up.
Full grill and turnspit are in operation. It is
suitable for grilling and making rotisserie
with large pieces of meat.
16
Sensitivity: Public
Lıst Ofcomponents/ Component Workıng Prıncıple
Convection fan assembly
Convection fan with rotisserie assembly
17
Sensitivity: Public
heating elements
signal Lamp
The warning light is lighting on, indicating that the oven is in operation. Power consumption
is very low.
18
Sensitivity: Public
TROUBLESHOOTING/ FAULT FINDING DIAGRAMS
Thermostat malfunctions
The oven is running continuously, the thermostat does not trip
19
Sensitivity: Public
Troubleshooting of oven (terminal)
No Elecricity on oven or power not transferring to appliance from oven
20
Sensitivity: Public
TOOLS FOR INSTALLATION/UNINSTALLATION
Cross screwdriver
straight screwdriver
combination cut pliers
21
Sensitivity: Public
INSTALLATION COMPONENTS /UNINSTALLATION
PS:Following instructions only for uninstalling of componets. Do opposite for installation of
components.
Oven Feet change
There are four rubber feet.
①Pull out the four rubber feet as shown.
②And then use the cross screwdriver to remove the four screws to remove the for support
feet.
22
Sensitivity: Public
23
Sensitivity: Public
Main enclosure and rear enclosure Change
① remove all the screws on the main enclosure.
24
Sensitivity: Public
② take the main enclosure.
25
Sensitivity: Public
③remove all the screws on the rear enclosure
④the power cord is connected with the rear enclosure. And there are so many wires
connect with the power cord.
26
Sensitivity: Public
⑤cut the tapes.
⑤ remove the wiring caps.
27
Sensitivity: Public
28
Sensitivity: Public
⑥ remove the screws beside the wire.
⑧pull out the wire.
29
Sensitivity: Public
⑨unbolt the wires.
30
Sensitivity: Public
⑩take the spacer under the power cord.
31
Sensitivity: Public
⑪pull out the power cord. And take the rear enclosure.
32
Sensitivity: Public
heat insulation plate
① Replace the screws on the heat insulation palte..
33
Sensitivity: Public
② take the heat insulation plate.
34
Sensitivity: Public
Front Door Change
①Open the front door complately
②remove the screw on the door axes and axes support. Then pull out the door with two
hands.
Sensitivity: Public
②remove the screws on the door to disassemble the door handle.
Sensitivity: Public
③there is sticky tape between door frame and front glass door. Pry it open with a straight
screwdriver carefully.
Sensitivity: Public
Sensitivity: Public
④remove the screws on the rear glass door.
Sensitivity: Public
Knob Change
You should draw to yourself. Replace the button with the new one.
Sensitivity: Public
Replacement of the control panel
①To do this, the knobs must first be removed and the side wall removed.
②remove all the screws in front of the control panel.
③Cut the tapes.
③ remove the wiring caps.
Sensitivity: Public
Sensitivity: Public
⑤Pull out the thermostat,switch and the timer behide the control panel. And then remove
the line that connect with the thermostat,switch and the timer.
Sensitivity: Public
⑥The panel is connect with the front plate. Remove all the screws on the front plate. Then
you can remove the front plate.
Sensitivity: Public
Sensitivity: Public
⑦ Remove the screws behide the panel. The panel is disassembled completely.
Sensitivity: Public
Convection fan assembly Change
①remove the screws on the convection fan assembly.
②Disassemble the convection fan assembly.
Sensitivity: Public
Lamp Change
①there are three buckles on the bottom of the lamp assembly. remove the line on the lame
assembly. Then unlock the buckles.
Sensitivity: Public
②hold the lamp assembly with two hands. Push in the direction of the inner oven to
disassemble the lamp assembly.
Sensitivity: Public
Oven Heating elements Change
①remove the screws beside the heating elements.
Sensitivity: Public
②pull out the heating element from one side.
Sensitivity: Public
EXPLODED VIEW
Explodedimages may varyaccording tothe type ofmodel and product . You can reach the
last exploded views on e-library by define model type.
Sensitivity: Public
16.SERVICE PART LIST
Service part lists may varyaccording tothe type ofmodel and product . You can reach the
last service part list on e-library by define model type.