Beko TBN7400W User Manual
Displayed below is the user manual for TBN7400W by Beko which is a product in the Blenders category. This manual has pages.
Related Manuals
TBN7400W
www.beko.com
Table Blender
User Manual
01M-8815093200-3918-01
EN
Dear Customers,
Thank you for selecting an Beko product. We hope that you get the best results from
your product which has been manufactured with high quality and state-of-the-art
technology. Therefore, please read this entire user manual and all other accompanying
documents carefully before using the product and keep it as a reference for future use.
If you handover the product to someone else, give the user manual as well. Follow all
warnings and information in the user manual.
Following symbols are used in the various section of this manual:
C
Important information and useful
hints about usage.
AWARNING:
Warnings for
dangerous situations concerning
the safety of life and property.
Materials are intended to be in
contact with food.
Do not immerse the appliance,
power cord or power plug in water
or in other liquids.
Potection class against electric
shock.
Ths product has been produced n envronmentally-frendly, state-of-the-art facltes.
Comples wth the WEEE Drectve. It does not contan PCB.
3 / EN
Table Blender / User Manual
CONTENTS
ENGLISH 4-12
4 / EN Table Blender / User Manual
This section contains safety
instructions that will help protect
from risk of personal injury or
property damage.
Failure to follow these instructions
invalidates the granted warranty.
• This appliance complies with the
international safety standards.
• This appliance can be used by
people who have limited physical,
sensory or mental capacity or
who do not have knowledge and
experience, provided that they are
supervised or they understand
the instructions with regard
to safe use of the product and
potential dangers.
• Do not use it if the power cable,
blades or the appliance itself is
damaged. Contact an authorised
service.
• Only use the original parts or
parts recommended by the
manufacturer.
• Do not attempt to dismantle the
appliance.
• Do not operate or place any part
of this appliance or its parts on or
near hot surfaces.
• Do not use the device for hot food.
• Your mains power supply should
comply with the information
supplied on the rating plate of the
appliance.
• Do not use the appliance with an
extension cord.
• Do not touch the plug of the
appliance with damp or wet hands.
• Do not pull the power cable when
unplugging the appliance.
• Unplug the appliance before
cleaning, disassembly, accessory
replacement and wait for it to stop
completely.
• When emptying the container,
during cleaning and grabbing
chopping blades with bare hands
serious injuries could result
due to incorrect use. Use the
plastic section trying to hold the
chopping blade.
• Never touch blades while using the
appliance. There is the possibility
of injury due to incorrect usage.
• After cleaning, dry the appliance
and all parts before connecting
it to mains supply and before
attaching the parts.
1
5 / EN
Table Blender / User Manual
• Do not immerse the appliance,
power cable, or power plug in
water or any other liquids.
• If you keep the packaging
materials, store them out of the
reach of children.
• Children shall not use the
appliance. Keep the appliance out
of the reach of children.
This product complies with EU WEEE Directive
(2012/19/EU). This product bears a classification
symbol for waste electrical and electronic
equipment (WEEE).
This product has been manufactured
with high quality parts and materials
which can be reused and are suitable
for recycling. Do not dispose of the
waste product with normal domestic
and other wastes at the end of its service life. Take
it to the collection center for the recycling of
electrical and electronic equipment. Please
consult your local authorities to learn about these
collection centers.
The product you have purchased complies with EU
RoHS Directive (2011/65/EU). It does not contain
harmful and prohibited materials specified in the
Directive.
Packaging materials of the product are
manufactured from recyclable
materials in accordance with our
National Environment Regulations. Do
not dispose of the packaging materials together
with the domestic or other wastes. Take them to
the packaging material collection points
designated by the local authorities.
Cut the solid food into small pieces before placing
them in the appliance as stated in the user manual.
Follow the other instructions and times specified
in the manual. Select low speed levels if suitable
for the food to be prepared. Switch off and unplug
the appliance after using it.
The moulded plug on this appliance incorporates
a 13 A fuse. Should the fuse need to be replaced
an ASTA approved BS1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the plug must
not to be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the pin
face of the plug Fuse covers are availabe from any
good electrical store.
1
6 / EN Table Blender / User Manual
•
•As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
•Brown cable = L (Live)
•Blue cable = N (Neutral)
•Green/yellow cable must be connected to
ground (E) line
•With the alternative plugs a 13 A fuse must be
fitted either in the plug or adaptore or in the
main fuse box. If in doubt contact a qualified
electrician.
1
7 / EN
Table Blender / User Manual
2 Table blender
The values whch are declared n the markngs axed on your applance or the other prnted documents suppled wth t repre-
sent the values whch were obtaned n the laboratores pursuant to the pertnent standards. These values may vary accordng
to the usage of the applance and ambent condtons.
1. Cap/Measuring cup
2. Lid opening
3. Lid
4. Jug
5. Jug handle
6. Blade unit
7. Sealing ring
8. Motor housing
9. Control dial
10. Non-slip feet
11. Cable storage coil
220-240 V~, 50-60 Hz
400 W
Technical and design modifications reserved.
1
2
3
4
7
8
6
5
9
10
11
8 / EN Table Blender / User Manual
3
C
Your blender has been designed
to process small amount of foods;
it must not be used for any other
purpose.
C
Do not use the it to chop extremely
hard ingredients such as coconut,
grains or bones. Remove the stalks
of plants, shells of walnuts, and
bones, sinews and gristles of meats.
C
Unplug the appliance when not in
use.
A
WARNING:
Switch off the
appliance and disconnect from
supply before changing accessories
or approaching parts that move in
use.
1. Remove all packaging and stickers materials
and dispose of them according to the applicable
legal regulations.
2. Take the entire unit of the motor housing
(8) and place it on a level surface, e.g. on the
kitchen counter.
3. Now set the jug (4) with the opening facing
down on a level surface.
4. Rotate the blade unit (6) clockwise and raise it
from the edges to remove it.
AWARNING:
Do not remove the
blade unit by lifting it from the
blades.
AWARNING:
The blade unit is
very sharp! Handle the blade unit
with utmost care, especially during
cleaning, in order to avoid injuries.
5. Clean all parts, with the exception of the motor
housing as described in “Cleaning and Care”.
6. Then re-assemble the jug blender in the reverse
order.
7. Put the jug D on the motor housing (8).
C
Make sure that the notches on the
bottom of the jug fit those in the
motor housing.
8. Cut the food into small pieces before using the
appliance.
1. Place the device on an even and dry surface.
The non-slip feet (10) ensure the stability of
the appliance.
2. Make sure that the power cord is disconnected
from the power supply and the control dial I is
on “0” before putting food into the jug.
3. To remove the reservoir (4) from the motor unit
(8), rotate it anti-clockwise and lift it. Put the
reservoir on a flat surface.
4. Rotate the measuring beaker (1) anti-clockwise
and lift to remove. Rotate the lid anticlockwise
and lift to open.
5. Now put the ingredients to be blended in the
jug (4). The ingredients should only be about
2-5 cm long.
C
Add water to ensure the jug blender
functions smoothly.
C
Mix 3 units of hard food and 2 units
of water in order to have a smooth
jug blender experience
(i.e: 60 gr hard food 40 ml water).
A
WARNING:
Do not put or blend
hot food or liquids in the jug. If you
process soup, make sure that the
liquid temperature does not exceed
40°C.
9 / EN
Table Blender / User Manual
3
AWARNING:
To process crushed
ice, we suggest you to start with
three quarters of ice in the jug and
add 15 ml of cold potable water.
AWARNING:
Don´t try to crush ice
without adding water to the jug.
AWARNING:
Never let the jug
blender operate while empty
(without food).
AWARNING:
Never let the jug
blender operate without the jug on
the motor housing.
6. Close the lid (3). Make sure that the cap/
measuring cup (1) is inside the lid opening and
is secured.
7. Place the jug (4) upright onto the motor housing
(8).
AWARNING:
Never move or turn
the jug after it is properly seated in
the place.
8. Connect the power plug to a suitable power
outlet.
9. The cutting speed can be variably adjusted with
the control dial (9).
C
To operate the blender at the low
speed, turn the control dial (9) to “1”.
C
If you want to blend with a higher
speed, turn the control dial (9) to the
desired speed level (2-3).
C
For short pulses of blending with a
high speed, turn the control dial (9)
to “P”. When you release the control
dial (9), the blender will stop and
return to “0” automatically.
C
If ingredients are to be added during
the blending process, then add them
through the opening in the lid (2). To
do this, take out the cap/measuring
cup (1).
10. After the desred consstency of the blended
food has been reached, turn the control dal
(9) to 0 to swtch off the blender
AWARNING:
Never run the blender
for longer than 1 minute, otherwise
it would overheat.
AWARNING:
After running the
appliance for 1 minute, let it cool
down before using it again.
AWARNING:
Be sure the motor
is switched off and has completely
stopped before removing the jug (4)
from the motor housing (8).
AWARNING:
Do not place any
utensil (scraper, fork, etc.) in the jug
while blender is operating.
11. Pull the power plug out of the power outlet.
12. To remove the reservor (4) from the motor
unt (8), rotate t ant-clockwse and lft t, and
then remove the measurng beaker (1).
13. Take off the ld and pour the mxture nto
glasses or other contaners.
10 / EN Table Blender / User Manual
4
•To add ice cubes to mixtures while the blender
is operating, add one cube at a time through the
cap (1). Wait a few seconds before adding the
next ice cube so that the blender can properly
blend the ice.
•To add food while the blender is operating,
remove the cap (1) and drop the ingredients
through the opening. Be sure to cut the food
into about 2-5 cm pieces to fit through the
opening. Replace the cap (1) when you have
finished adding ingredients.
•When blending solid food, such as raw
vegetables, cooked or uncooked meat and fruits
always cut them into no larger than 2-5 cm
pieces before placing them into the jug. Blend
no more than 2 cups of these food at a time.
This will speed the blending process and reduce
wear on the blending blades.
•Always place liquid ingredients in the jug first,
unless a recipe specifically states otherwise.
•To blend beverages, place all ingredients in the
jug at the same time.
•Avoid overblending. Usually, you will need to
blend for a few seconds.
•Overblending may cause food to become mushy.
AWARNING:
Never use petrol
solvents, abrasive cleaners, metal
objects or hard brushes to clean the
appliance.
AWARNING:
The blades of the
cutter unit are very sharp! Handle
the blades with utmost care in order
to avoid injuries.
AWARNING:
Never clean the
appliance with your bare hands.
A
WARNING:
Clean the jug blender
after each use. Do not let any food
remnants harden on and inside the
jug blender. This will make it more
difficult to clean it later.
A
WARNING:
Do not use boiling
water. The blade assembly bearings
have been designed with a lifetime
lubricant; exposure to boiling water
may damage these bearings and
shorten the life of the blender.
1. Turn the appliance off and disconnect it from
wall socket.
2. Allow the appliance to cool down.
3. Remove the jug D from the motor housing (8).
Rinse with water to remove any large food
particles that may have accumulated in the jug.
C
You can use the measuring cup (1) to
remove the blender blade.
4. Turn the glass container over and place it on a
level, non-slip surface. Attach the measuring
cup (1) by placing it over the cutting blade unit
(6). Remove the cutting blade unit (6) by turning
it with the measuring cup in the direction of the
“open lock symbol” (counterclockwise). Glass
container, lid and measuring cup can now be
washed in the dishwasher. Carefully rinse the
cutting blade unit under running water.
5. To place the blade unit (6) back to the glass
container (4), turn the blade unit (6) to the
locking “ ” direction (clockwise) using the
measuring cup (1).
6. Replace the jug (4) on the motor
housing (8).
7. Place 1 to 1 ½ cups warm water with some
drops of mild cleanser into the jug (4) and
switch to speed “4” for a few seconds. Remove
the jug from the motor housing and rinse with
water. Repeat as necessary.
11 / EN
Table Blender / User Manual
4
C
Do not immerse the motorized base
or blade unit in liquid, or place them
in the dishwasher. Only the lid and
the jug may be immersed and placed
in the dishwasher.
8. Use a damp soft cloth and some mild cleanser to
clean the exterior of the appliance.
9. Wipe the blender base, cutter unit (6) and lid
with a lint free cloth before the next usage.
If you do not plan to use the appliance for a long
period of time, please store it carefully. Make sure
the appliance is unplugged and completely dry.
Store the appliance in a cool, dry place. Make sure
the appliance is kept out of the reach of children.
•During handling and transportation, carry
the appliance in its original packaging. The
packaging of the appliance protects it against
physical damages.
•Do not place heavy loads on the appliance or the
packaging. The appliance may be damaged.
•Dropping the appliance will render it non-
operational or cause permanent damage.
12 months breakdown and repair guarantee
Product Guarantee
Guarantor: Beko plc, 1 Greenhill Crescent, Watford, Hertfordshire. WD18 8UF
The guarantee does not in any way diminish your statutory or legal rights.
Your appliance has the benefit of our manufacturer’s guarantee which covers the product for 12 months
from the date of original purchase.
This gives you reassurance that if within that time, your appliance is proven to be defective because of
either workmanship or materials, we will at our discretion either repair or replace your appliance.
The appliance must be correctly installed, located and operated in accordance with the instructions
contained in the user manual.!The guarantor disclaims any liability for accidental or consequential damage.
The Guarantee is subject to the following conditions:
Documentary proof of the original purchase date is provided.
The appliance has been installed and operated correctly and in accordance with our operating and maintenance
instructions.
The appliance is used only on the electricity supply on the rating plate.
The appliance has only been used for normal domestic purposes.
The appliance has not been altered, serviced, dismantled or otherwise interfered with by any person.
The appliance is used in the United Kingdom or Republic of Ireland.
Any parts removed during repair work or any product that has been replaced becomes our property.
The guarantee is not transferrable if the product is resold.
The Guarantee does not cover:
Transit, installation or delivery damage.
Accidental damage.
Misuse or abuse.
Replacement of any consumable item or accessories. These include but are not limited to: plugs, cables, light bulbs,
knobs, filters and flaps.
Repairs or replacements required as a result of unauthorised repairs or inexpert installation that fails to meet the
requirements contained in the user guide or instruction book.
Repairs to products used in commercial or non-residential household premises.
How to obtain after sales service, help or general advice
Please keep your purchase receipt or other proof of purchase in a safe place as you will need to
show us this document if your product requires attention within the guarantee period.
Please also record your product details below, which will allow you to access our services more quickly and
help us identify your product. The model number is printed on the front of the user guide and the serial and
model number is shown on your products rating plate.
Model number
Serial number
Purchased from
Date of purchase
Please call our UK based Customer Service department if you need help or advice from us:
United Kingdom and Northern Ireland: 0333 207 9710
Republic of Ireland: 01 862 3411
You can also contact us through our website: www.beko.co.uk
www.beko.co.uk
Arçelik A.Ş.
Karaağaç Cad. No: 2-6, Sütlüce, 34445
İstanbul, Türkiye