Beko UL584AP User Manual
Displayed below is the user manual for UL584AP by Beko which is a product in the Fridges category. This manual has pages.
Related Manuals
UL584APW
UL584APS
Larder Fridges
Please read this manual first!
Dear Customer,
We hope that your product, which has been produced in modern factories and
checked under the most meticulous quality control procedures, will provide you
with years of good service.
For this, we recommend you to carefully read the entire manual of your product
before using it and keep it at hand for future reference.
• This manual will help you use your appliance quickly and safely.
• Read the manual before installing and operating your product.
• Follow the instructions, especially those about safety warnings.
• Keep the manual in an easily accessible place as you may need it later.
• Also read the other documents provided with your product.
Symbols and their descriptions
This instruction manual contains the following symbols:
C Important information or useful usage tips.
A Warning against dangerous conditions for life and property.
B Warning against electric voltage shock.
EN
3
1 Your refrigerator 4
2 Warnings 5
Electrical requirements ....................... 6
Warning! This appliance must be
earthed .............................................. 6
Energy saving tips ............................. 6
Compliance with WEEE Directive and
Disposing of the Waste Product: ....... 7
Compliance with rohs directive: ........ 7
Package information .......................... 7
3 Installation 8
Transportation Instructions ................. 8
Installation Instructions ...................... 8
CONTENTS
4 Before operating 12
Final Check .....................................12
5 Using your refrigerator 13
Temperature Control And
Adjustment ...................................... 14
Defrosting ........................................ 15
6 Maintenance and
cleaning 16
7 Do's and Don'ts 17
8 Guarantee Details 18
9 How To Obtain Service 19
EN
4
1 Your refrigerator
C Figures that take place in this instruction manual are schematic and may not
correspond exactly with your product. If the subject parts are not included in the
product you have purchased, then it is valid for other models.
Congratulations on your choice of a BEKO quality Appliance which has been
designed to give you service for many years.
1. Movable shelves
2. Interior light & Thermostat knob
3. Wine rack
4. Defrost water collection channel -
Drain tube
5. Crisper cover
6. Crisper
7. Adjustable front feet
8. Door shelves
9. Egg tray
10. Bottle shelf
11. Top trim
2
5
6
3
7
4
1
11
8
8
10
9
EN
5
2 Warnings
• Do not connect your appliance to
the electricity supply until all packing
and transit protectors have been
removed.
• If transported horizontally leave
to stand upright for at least 4
hours before switching on to allow
compressor oil to settle
• If you are discarding an old
refrigerator with a lock or latch fitted
to the door, disable the lock/latch,
ensure that it is left in a safe condition
to prevent the entrapment of young
children.
• This fridge/freezer must only be used
for its intended purpose i.e the storing
and freezing of edible foodstuff.
• Do not dispose of the appliance
on a fire. At BEKO, the care and
protection of our environment is an
ongoing commitment. This appliance
which is among the latest range
introduced is particularly environment
friendly. Your appliance contains non
CFC / HFC natural substances in the
cooling system (Called R600a) and in
the insulation (Called cyclopentane)
which are potentially flammable
if exposed to fire. Therefore, take
care not to damage, the cooling
circuit / pipes of the appliance in
transportation and in use. In case of
damage do not expose the appliance
to fire or potential ignition source and
immediately ventilate the room where
the appliance is situated.
• We suggest you contact your local
authority for disposal information and
facilities available.
• See Installation Instructions on page
8 for information on suitable location.
• To obtain the best possible
performance and trouble free
operation from your appliance it is
very important to carefully read these
instructions.
• On delivery, check to make sure that
the product is not damaged and that
all the parts and accessories are in
perfect condition.
• Ensure that the plug remains readily
accessible. Do not use multiple
adapter or extension cable.
• Failure to observe these instructions
may invalidate your right to free
service during the guarantee period.
• Keep ventilation openings, in the
appliance enclosure or in the built-in
structure, clear of obstruction.
• Do not use mechanical devices
or other means to accelerate the
defrosting process, other than those
recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• Do not use electrical appliances
inside the food storage
compartments of the appliance,
unless they are of the type
recommended by the manufacturer.
• We suggest you keep these
instructions in a safe place for easy
reference.
• This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or
lack of experience and knowledge
if they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
EN
6
maintenance shall not be made by
children without supervision.
• Children should be supervised to
ensure that they do not play with the
appliance.
Electrical requirements
Before you insert the plug into the wall
socket make sure that the voltage and
the frequency shown on the rating
plate inside the appliance corresponds
to yourelectricity supply.
Rating label is on the left hand side of
fridge inner liner.
We recommend that this appliance be
connected to the mains supply via a
Suitable switched and fused socket.
The appliance must be positioned so
that the plug is accessible.
Should the mains lead of the appliance
become damaged or should it need
Replacing at any time, it must be
replaced by a special purpose made
mains lead which can only be obtained
from a BEKO authorised service
agent.
Warning! This appliance
must be earthed
If the fitted moulded plug is not
suitable for your socket, then the plug
should be cut off and an appropriate
plug fitted. Destroy the old plug which
is cut off as a plug with bared cord
could cause a shock hazard if inserted
into a socket elsewhere in the house.
The moulded plug on this appliance
incorporates a 13 A fuse. Should
the fuse need to be replaced an
ASTABEAB approved BS 1362 fuse
of the same rating must be used. Do
not forget to refit the fuse cover. In the
event of losing the fuse cover the plug
must not be used until a replacement
fuse cover has been fitted.
Colour of the replacement fuse cover
must be the same colour as that
visible on the pin face of the plug. Fuse
covers are available from any good
electrical store.
Important! Fitting A Different Plug
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals in
your plug proceed as follows: (See
diagram).
1. Connect the green-yellow or green
(Earth) wire to the terminal in the plug
marked ‘E’ or with the symbol or
coloured green and yellow or green.
2. Connect the blue (Neutral) wire to
the terminal in the plug marked ‘N’ or
coloured black.
3. Connect the brown (Live) wire to the
terminal in the plug marked ‘L’ or
coloured red.
With alternative plugs a 13 A fuse must
be fitted either in the plug or adaptor
or in the main fuse box. If in doubt
contact a qualified electrician.
Energy saving tips
1. Ensure your appliance is installed in a
well ventilated area.
2. Ensure the time between buying
chilled/frozen food and placing
them in your appliance is kept at
minimum, particularly in summer. We
recommend you use a cool bag or a
special carrier bag to carry perishable
food.
3. Do not leave the door (s) of your
appliance open longer than
necessary and ensure they are closed
properly after each opening.
4. Defrost frozen food in the fridge
compartment, so that frozen food
acts as an ice pack to assist cooling
in the fridge.
EN
7
5. Energy consumption of this
appliance is measured while freezer
compartment is loaded without
use of top shelf lid and the drawers
except the bottom drawer. It is
advised that freezer compartment is
loaded without use of drawers except
the bottom drawer in order to achieve
maximum loading capacity.
Compliance with WEEE
Directive and Disposing of
the Waste Product:
This product complies with EU WEEE
Directive (2012/19/EU). This
product bears a
classification symbol for
waste electrical and
electronic equipment
(WEEE).This product has
been manufactured with
high quality parts and materials which
can be reused and are suitable for
recycling. Do not dispose of the waste
product with normal domestic and
other wastes at the end of its service
life. Take it to the collection center for
the recycling of electrical and
electronic equipment. Please consult
your local authorities to learn about
these collection centers.
Compliance with rohs
directive:
The product you have purchased
complies with EU RoHS Directive
(2011/65/EU). It does not contain
harmful and prohibited materials
specified in the Directive.
Package information
Packaging materials of the product
are manufactured from recyclable
materials in accordance with our
National Environment Regulations. Do
not dispose of the packaging materials
together with the domestic or other
wastes. Take them to the packaging
material collection points designated
by the local authorities.
EN
8
3 Installation
Transportation Instructions
1. The appliance should be transported
only in a vertical upright position. The
packing as supplied must be intact
during transportation.
2. If during the course of transport the
appliance has to be transported
horizontally, it must only be laid on its
right hand side when standing in the
front of the appliance. After bringing
it to upright position,it must not be
operated for at least 4 hours to allow
the system to settle.
3. Failure to comply with the above
instructions could result in damage
occuring to the appliance. The
manufacturer will not be held
responsible if these instructions are
disregarded.
4. The appliance must be protected
against rain, moisture and other
atmospheric influences.
5. Empty any water in the drain
tray before moving see section
“Defrosting” and “Cleaning & Care”
for further information
IMPORTANT :
Make sure the plastic evaporating pan
at the back of the product collects
water properly.
IMPORTANT:
Care must be taken while cleaning
/ carrying the appliance to avoid
touching the bottom of the condenser
metal wires at the back of theappliance
as you might injure your fingers and
hands.
IMPORTANT:
This appliance is not designed for
stacking with any other appliance.
When positioning your appliance, take
care not to damage your flooring,
pipes,wall coverings etc. Do not
move the appliance by pulling by the
door or handle.Do not attempt to sit
or stand on top of your appliance as
it is not designed for such use. You
could injure yourself or damage the
appliance.
IMPORTANT:
Make sure that mains cable is not
caught under the appliance during and
after carrying / moving the appliance,
to avoid the mains cable becoming cut
or damaged.”Do not allow children to
play with the appliance or tamper with
the controls.
BEKO declines to accept any liability
should the instructions not be
followed.
Installation Instructions
1. If possible avoid placing the appliance
near cookers, radiators or in direct
sunlight as this will cause the
compressor to run for long periods.
If installed next to a source of heat
or refrigerator, maintain the following
minimum side clearances:
From Cookers 2” (50 mm)
From Radiators 12” (300 mm)
From Refrigerators or Larder Fridge 1”
(25 mm)
2. No gap is required at sides and top.
See item 3 below to ensure a gap is
obtained at the rear of the appliance.
If a gap is available on side and
top, retain it if possible as it would
improve the air circulation around the
appliance.
EN
9
3. Fit the two plastic wall spacer
supplied with the appliance on to
the condenser at the back of the
refrigerator by rotating 1/4 turn (see
diagram).
4. The appliance should be located
on a smooth surface. The two front
feet can be adjusted as required. To
ensure that your appliance is standing
upright adjust the two front feet, by
turning clockwise or anti-clockwise,
until the product is in firm contact with
the floor. Correct adjustment of feet
avoids excessive vibration and noise.
5. Refer to “Cleaning and Care” section
to prepare your appliance for use.
6. This appliance has been designed
to operate in ambient temperatures
between +10 and +32 degrees C (50
and 90 degrees F). Therefore if the
appliance is installed in an unheated
/ cold room (E.g.: Conservatory /
annex / shed / garage etc.) then the
appliance may not operate and as a
result the storage time of food may
be reduced.
7. A special receptacle is supplied to
store the mains plug during transit.
The receptacle is fixed at the back of
the cabinet, on the right hand side of
the compressor. (See diagram) Gently
remove the plug from the receptacle.
8. Never pull the mains cord, you may
damage the appliance. In the case
of transportation, ensure you locate
the plug in the receptacle provided
to avoid transit damage.The space
in the room where the appliance is
installed must not be smaller than 10
cubic metres.
EN
10
Repositioning The Door
Follow the step by step instructions and the diagram below.
Numbers in brackets refer to diagrams.
1
60°
10
6
2
3
4
5
8
7
9
EN
11
1. Switch off at the socket outlet and
pull out the mains plug.
2. Remove all food, loose items and
fittings from inside the appliance and
door shelves.
3. Carefully tilt the appliance on its back
side. (1) (You may need somebody to
help you.) Take care not to damage
the appliance by laying on some
protective material (e.g. its original
packaging). Make sure that you
tilt the appliance on its back side,
otherwise compressor oil may block
the pipes and you may damage the
appliance.
4. Unscrew and remove the LHS front
feet and bolt (2).
5. Unscrew the bolts and remove the
bottom hinge while holding the door
(3).
6. Remove the door carefully from the
top hinge by sliding down wards (4).
7. Reposition top hinge bushing and
blanking plug on the opposite side
and stand the door safely (5). You
may find it easier to remove the
bushing and the plug with the tip of
a small screwdriver. Take care not to
mark the door.
8. Reposition the top hinge on the
opposite side (6 and 7).
9. To refit the door, locate the top hinge
in the door, attach to the cabinet and
hold the door (8).
10. Fit the bottom hinge (9). If necessary
adjust and then tighten the bolts.
Ensure,that the door opens and
closes easily and that there are no
gaps allowing air into the cabinet. If
there are gaps between the door seal
and the cabinet,adjust the door seal
by gently pulling away from the door
using fingers.
11. Fit the other front feet .
12. Fit the plugs on the holes on inner
liner .
13. 19. Carefully stand your appliance.
(You may need somebody to help
you.)
14. Adjust the front feet (See Installation
Instructions)
15. Put back all, loose items and fittings.
16. Wait for at least 4 hours to allow the
system to settle before switching
on.Spare plastic parts supplied with
the appliance are for your future use
during door repositioning.
EN
12
4 Before operating
Final Check
Before you start using the fridge/
freezer check that:
1. The feet have been adjusted for
perfect levelling.
2. The interior is dry and air can circulate
freely.
3. Clean the interior as recommended
under “Cleaning And Care.”
4. Insert the plug into the wall socket
and switch on the electricity supply.
When the door is open the interior
light will come on.
5. You will hear a noise as the
compressor starts up. The liquid and
gases sealed within the refrigeration
system may also give rise to noise,
whether the compressor is running or
not which is quite normal.
6. Slight undulation of the top of the
cabinet is quite normal due to the
manufacturing process used, so do
not worry, it is not a defect.
7. We recommend that you set
the thermostat knob at 3 (three)
and monitor the temperature to
ensure the appliance maintains
desired storage temperatures (See
section Temperature Control and
Adjustment).
8. Do not load the appliance
immediately it is switched on. Wait
until the correct storage temperature
has been reached. We recommend
that you check the temperature
with an accurate thermometer
(see; Temperature Control and
Adjustment).
9. Important Note :Ice formation at the
back is normal, do not worry. (See
Defrosting)
EN
13
5 Using your refrigerator
Arrangement Examples (See
diagram).
1. Baked, chilled cooked food, dairy
products.
2. Meat, sausages, cold cuts, cans.
3. Wine rack
4. Fruit, vegetables, salads.
5. Tubes, small bottles and cans.
6. Egg tray.
7. Butter, cheese, dairy products.
8. Beverages, large bottles.
The following guidelines and
recommendations are suggested to
obtain the best results and storage
hygiene.
1. Appliance is for the short term
storage of fresh food and drinks.
2. Cooked dishes must be stored
in airtight covered containers and
are best placed on either of the
removable shelves.
3. Fresh wrapped produce can be
placed on the shelf. Fresh fruit and
vegetables should be cleaned and
stored in the crisper bins.
4. Bottles can be placed in the door
section.
5. To store raw meat, wrap in polythene
bags and place on the lowest
shelf. Do not allow to come into
contact with cooked food to avoid
contamination. For safety, only store
raw meat for two to three days.
6. Shelves incorporate rear stops and
tilting for storing bottles. Lift shelf to
clear grooves when adjusting.
7. To tilt a shelf place the back of the
shelf one level below the front of the
shelf. To remove a tilted shelf, first
release the back off the grooves and
then pull it.
2
5
6
7
3
4
1
8
.
.
.
.
EN
14
8. Keep the food packed, wrapped
or covered. Allow hot food and
beverages to cool before placing
them in the fridge. Do not store
explosive substances in the
refrigerator. High proof alcohol
must be stored upright in sealed
containers. Left over canned food
should not be stored in the can.
9. Side handle to be fitted by the
user (Supplied in the appliance)
10. Some fruit and vegetables suffer
damage if kept at temperatures near
0 degrees centigrade. Therefore
wrap pineapples, melon, cucumbers,
tomatoes and similar produce in
polythene bags.
11. Shelves, racks, crisper bins, dairy
compartments, drawers, bottle
grippers are all removable.
12. Always wrap food using a suitable
packaging material before storing
in your appliance to avoid contact
with the appliance surface and food
remains for hygiene reasons.
Temperature Control And
Adjustment
Operating temperatures are
controlled by the thermostat
(seediagram). Settings may be
made from 1 to 5, the coldest
position.
When the appliance is
switched on for the first
time, the thermostat should
be adjusted so that after
24 hours, theaverage fridge
temperature is no higher than
+5°C (+41°F).
We recommend you set the
thermostat halfway between
the 1 and 5 setting and
monitor to obtain the desired
temperature i. e. towards 5
you will obtain a colder fridge
temperature and vice versa.
Some sections of the fridge may be
cooler or warmer ( such as the salad
crisper and the top part of the cabinet
) which is quite normal.Over ambient
temperatures of 25°C (77°F) especially
in summer turn the thermostat
knob towards 5. Under ambient
temperatures of 25°C (77°F) turn the
thermostat knob to a half way position.
Frequent door opening cause higher
internal temperatures, so close the
door as soon as possible after use.
In case of a temporary ice build up in
the fridge compartment reduce the
thermostat setting to 1, monitoring
at the same time that the fridge
temperature is maximum +5 degrees
C (41 degrees F). Once the ice build
up disappears and the appliance
starts auto defrosting again as normal,
then you may increase the thermostat
setting, if required.
EN
15
Defrosting
The larder fridge defrosts automatically.
The defrosting water runs to the drain
tube via a collection channel and is
evaporated in a special container (1)
at the back of the appliance (see
diagram).
During defrosting water droplets
may format the back of the larder
fridge where concealed evaporator is
located. Some droplets may remain on
the liner and refreeze when defrosting
is completed.
Do not use pointed or sharp edged
objects such as knives, forks to
remove the droplets which have
refreezed.If at any time the defrost
water does not drain from the
collection channel, check to ensure
that no food particles have blocked
the drain tube. The drain tube can be
cleared by pushing the special plastic
plunger provided down the drain tube.
1
2
Replacing The Interior Light Bulb
(See Diagram)
Should the light fail to work switch
off at the socket
outlet and pull out
the mains plug.
Follow the below
instructions to
check if the light
bulb has worked
itself loose.
If the light still fails
to work obtain a
replacement E14
screw cap type 15
Watt (Max) bulb
from your local
electrical store
and then fit it as
follows:
1. Switch off at
the socket
outlet and pull
out the mains
plug. You may
find it useful to
remove shelves
for easy access.
2. Remove the
light diffuser
cover as shown
in figure (b-c).
3. Replace the
burnt-out light
bulb.
4. Reassemble the light diffuser cover
as shown in figure (d).“Push firmly to
ensure cover is fitted properly.”
5. Carefully dispose of the burnt-out
light bulb immediately.“Replacement
light bulb can easily be obtained
from a good local electrical or DIY
store.”
EN
16
6 Maintenance and cleaning
• We recommend that you switch off
the appliance at the socket outlet
and pull out the mains plug before
cleaning.
• Never use any sharp abrasive
instrument, soap, household
cleaner, detergent and wax polish for
cleaning.
• Use luke warm water to clean the
cabinet of the appliance and wipe it
dry.
• Use a damp cloth wrung out in
a solution of one teaspoon of
bicarbonate of soda to one pint of
water to clean the interior and wipe
it dry.
• If the appliance is not going to be
used for a long period of time switch
it off,remove all food, clean it and
leave the door ajar.
• Any dust that gathers on the
condenser, which is located at the
back of the should be removed once
a year with a vacuum cleaner.
• Check door seals regularly to ensure
they are clean and free from food
particles..
• Never :
• Clean the worktop with
unsuitablematerial; eg petroleum
based products.Subject it to hot
temperatures in any way.Scour, rub
etc., with abrasive material.
EN
17
7 Do's and Don'ts
Do- Clean your appliance regularly
(See “Cleaning and Care”)
Do- Keep raw meat and poultry below
cooked food and dairy products.
Do-Keep food for as short a time as
possible and adhere to ‘Best Before’
and “Use By” dates.
Do- Take off any unusable leaves on
vegetables and wipe off any soil.
Do- Leave lettuce, cabbage, parsley
and cauliflower on the stem.
Do- Wrap cheese firstly in greaseproof
paper and then in a polythene bag
excluding as much air as possible.
For best results take out of the fridge
compartment an hour before eating.
Do- Wrap raw meat and poultry
loosely in polythene or aluminium foil.
This prevents drying.
Do- Wrap fish and offal in polythene
bags.
Do- Wrap food which have a strong
odour or can dry out in polythene
bags, aluminium foil or place in an
airtight container.
Do- Wrap bread well to keep it fresh.
Do- Chill white wines, beer, lager and
mineral water before serving.
Don’t- Store bananas in your fridge.
Don’t- Store melon in your fridge. It
can be chilled for short periods as long
as it is wrapped to avoid it flavouring
other food.
Don’t- Leave the door open for long
periods as this will make the larder
refrigerator more costly to run.
Don’t- Don’t- Store poisonous or any
dangerous substances in the larder
refrigerator. Your larder refrigerator
has been designed for the storage of
edible foodstuffs only.
Don’t- Consume food which has been
stored for an excessive time in the
larder refrigerator.
Don’t- Consume food which has been
stored for an excessive time in the
larder refrigerator.
Don’t- Store cooked and fresh food
together in the same container. They
should be packaged and stored
seperately.
Don’t- Let defrosting food or food
juices drip onto food in your larder
refrigerator.
Problem Solvıng
If the appliance does not operate when
switched on, check whether:
• The plug is inserted properly in the
socket and that the power supply is
on. (To check the power supply to
the socket, plug in another appliance)
• The fuse has blown/circuit breaker
has tripped/main distribution switch
has been turned off.
• The temperature control has been set
correctly.
• New plug is wired correctly if you
have changed the fitted moulded
plug.
If the appliance is still not operating
after the above checks, please refer
to the section on “How To Obtain
Service”.
Please ensure that above checks have
been made as a charge will be made if
no fault is found.
EN
18
GUARANTEE DETAILS
Your new Beko product is guaranteed against the cost of breakdown repair for
twelve months from the date of the original purchase.
What is covered?
•Repairs necessary as a result of faulty materials, defective components or
manufacturing defect.
•The cost of functional replacement parts, but excluding consumable items.
•The labour costs of a Beko approved repairer to carry out the repair.
What is not covered?
•Transit, delivery or accidental damage or misuse and abuse.
• Cabinet or appearance parts, including control knobs, flaps, handles or
container lids.
•Accessories or consumable items including but not limited to, ice trays,
scrapers, cutlery baskets, filters and light bulbs.
•
Repairs required as a result of unauthorised repair or inexpert installation that
fails to meet the requirements contained in the user instruction book.
•Repairs to products used on commercial or non-residential household
premises.
•Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is
often included within your household contents insurance policy, or may be
available separately from your retailer).
Important notes.
•Your Beko product is designed and built for domestic household use only.
•The guarantee will be void if the product is installed or used in commercial
or non-residential domestic household premises.
•
The product must be correctly installed, located and operated in accordance
with the instructions contained in the User Instructions Booklet provided.
•Professional installation by a qualified Electrical Domestic Appliance Installer
is recommended for all Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a
Gas Safe (or BORD GAIS) registered
Gas Installer.
•The guarantee is given only within the boundaries of the United Kingdom
and the Republic of Ireland.
•The guarantee is applicable only to new products and is not transferable if
the product is resold.
•Beko disclaims any liability for incidental or consequential damages.
The guarantee does not in anyway diminish your statutory or legal rights.
8 Guarantee Details
EN
19
HOW TO OBTAIN SERVICE
Please keep your purchase receipt or other proof of purchase in a safe
place; you will need to have it should the product require attention under
guarantee.
You should also complete the details below; it will help us assist you when
requesting service. (The model number is printed on the Instruction Booklet and
the serial number is printed on the Rating Label affixed to the appliance)
Model No: Serial No: Retailer: Date of purchase:
For service under guarantee simply telephone the appropriate number
below
UK Mainland & Northern Ireland
Fridges & Freezers 0845 6004903
Electric Cookers 0845 6004902
Gas & Dual Fuel Cookers 0845 6004905
Washing Machines 0845 6004906
& Dishwashers
Republic of Ireland
All Refrigeration, All Cookers 01 862 3411
Washing Machines & Dishwashers
Before requesting service please check the trouble-shooting guide in
the Operating Instructions as a charge may be levied where no fault is
found even though your product may still be under guarantee.
Service once the manufacturers guarantee has expired.
If you have purchased an extended guarantee please refer to the instructions
contained within the extended guarantee agreement document. Otherwise
please call the appropriate number above where service can be obtained at a
charge.
Should you experience any difficulty in obtaining service please contact the Beko
Customer Help-Line. Tel: 0845 6004911 e-mail: service@beko.co.uk
9 How To Obtain Service
Printed in Turkey
Part no:
Revision no:
BEKO plc
Beko House
Caxton Way
Watford
Hertfordshire
WD18 8UF
Tel: 0845 6004911
Fax: 0845 6004922
e-mail: service@beko.co.uk
website: www.beko.co.uk
AH
57 1227 0000