Table of Contents
- To Start Menu
- How to Use This Manual
- Table of Contents
- Projector Highlights
- Safety Instructions
- For Safe Use
- Before Installation
- Open Source Software
- Before Use
- Basic Guide
- Installation Procedure
- Connection Procedure
- Projection Procedure
- Convenient Features
- Advanced Guide
- Using Menus
- Menu Configuration
- Menu Description
- Input settings
- Image adjustment
- Install settings
- Positional lock
- Image flip H/V
- Screen aspect
- Zoom
- Keystone
- Digital image shift
- Professional settings
- Micro-digital image shift
- Registration
- Fan mode
- Vertical projection
- Edge blending
- Lens - Position
- Screen color
- On screen
- Menu position
- Guide
- Show input status
- Overheat warning display
- Menu display time
- Lamp warning display
- Air filter warning display
- Split screen ID display
- Test pattern
- System settings
- User screen settings
- Logo capture
- Logo position
- No signal screen
- Screen when blank
- Projector on
- Interface settings
- Key repeat
- Key lock
- Remote control channel
- Audio in terminal select
- HDBaseT
- Communication settings
- HDMI image input
- HDBaseT image input
- Power management mode
- Power management duration
- Direct power on
- Beep
- Motion blur reduction
- Language
- Other settings
- Password settings
- Register password
- [Fn] button settings
- Gamma restore
- Lamp counter
- Air filter counter
- Power counter
- Firmware
- Factory defaults
- Network settings
- Completing Projector Settings
- Completing Computer Settings
- Checking Projector Information
- Advanced Projection
- Other Information
Canon REALiS WUX6500 D Pro AV User Manual
Displayed below is the user manual for REALiS WUX6500 D Pro AV by Canon which is a product in the Data Projectors category. This manual has pages.
Related Manuals
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced Guide
Using Menus
Menu Configuration
Menu Description
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
ENG
MULTIMEDIA PROJECTOR
User’s Manual
2
How to Use This Manual
Thank you for purchasing a Canon projector.
The WUX6500 Multimedia Projector is a high-performance projector that is
capable of projecting a high-resolution computer screen and high-quality
digital image on a large screen.
This Manual
This is the user’s manual for WUX6500 Multimedia Projectors (hereafter,
“projector”). The “Basic Guide” section describes installation and basic use of the
projector. Descriptions of menus and how to connect the projector to a network are
given in the “Advanced Guide” section. Read this manual thoroughly to make the
most of your projector. We recommend requesting installation by a qualified
technician or the Canon Customer Support Center.
Selecting Screen Aspect
Select the correct aspect ratio for the screen which is used.
1
Press the MENU button to display the menu window.
Remote control Projector
Symbols Used in This Manual
Sections labeled with these symbols give the following kinds of information.
Indicates precautions and information to note when using the projector.
Symbols of Button Operations
The projector can be operated using the buttons on the remote control or on the
side of the projector. The remote control allows you to operate all functions of the
projector.
In this document, the button’s operations are shown as below.
Remote control button
operation
Operation of buttons
on side of projector
Indicate the buttons to
be pressed
3
Table of Contents
How to Use This Manual............... 2
Projector Highlights...................... 5
Safety Instructions........................ 7
Safety Precautions................................. 8
CAUTION ON HANGING FROM THE
CEILING .................................................. 8
AC Power Cord Requirement.............. 11
Federal Communication Commission
Notice .................................................... 12
Precautions for Use ............................. 14
Installation and Handling
Precautions .......................................... 15
Precautions on the Lamp .................... 17
Precautions for the Batteries of the
Remote Control .................................... 18
For Safe Use ................................ 20
Before Installation....................... 22
Precautions When Carrying/Shipping
the Projector......................................... 22
Precautions for Installation................. 22
Open Source Software ............... 27
Before Use ................................... 28
Included Accessories .......................... 28
Part Names ........................................... 29
Projector ............................................... 29
Side Control.......................................... 30
LED Indicators...................................... 31
Input Terminal ...................................... 33
Remote Control .................................... 35
Preparing the Remote Control............ 37
Basic Guide ............................39
Installation Procedure ................ 40
Setting Up the Projector...................... 40
Relationship Between Image Size and
Projecting Distance ............................. 43
Lens Shift Function ............................. 47
Connection Procedure ............... 49
Connecting a Computer ...................... 49
Connecting AV Equipment.................. 51
Plugging the Projector In .................... 52
Projection Procedure.................. 53
Step 1 Turn the Projector On .............. 53
Step 2 Select an Input Signal.............. 56
Step 3 Adjust the Image ...................... 57
Step 4 Select an Aspect Ratio (Screen
Aspect) Matching the Screen.............. 63
Step 5 Adjusting Keystone
Distortion .............................................. 67
Step 6 Select the Image Quality (Image
Mode) .................................................... 70
Step 7 Turn the Projector Off.............. 71
Convenient Features...................72
Adjusting the Volume .......................... 74
Muting the Sound................................. 74
Zooming Part of an Image................... 75
Advanced Guide ....................77
Using Menus ................................78
Menu Configuration ............................. 78
Basic Menu Operations ....................... 79
Menu Configuration ....................81
Menu Description ........................90
Input settings ....................................... 90
Image adjustment ................................ 96
Install settings.................................... 104
System settings ................................. 116
Network settings ................................ 127
Completing Projector Settings ......... 129
Completing Computer Settings ........ 136
Checking Projector Information ....... 156
Advanced Projection.................157
Projecting Images on a USB Flash
Drive .................................................... 157
Description of USB File Browser...... 159
Selecting an Image for Projection .... 160
Operating the Projected Image......... 160
Running a Slideshow of Data Saved in a
USB Flash Memory ............................ 161
Split-Screen Display .......................... 161
Projecting from Multiple Projectors at
Once (Edge Blending) ....................... 162
Other Information ................169
Maintenance...............................170
Cleaning the Projector and the Air
Filter .................................................... 170
Cleaning the Air Filter........................ 171
Replacing the Air Filter...................... 172
Replacing the Lamp........................... 173
Replacement Lamp ............................ 175
Table of Contents
4
Lamp Replacement Procedure ......... 176
Installing / Removing the Lens
Unit ...................................................... 178
Product Specifications ............. 183
Relationship between Aspect and
Screen Aspect .................................... 183
Displayed Test Patterns .................... 187
Supported Signal Types.................... 188
Troubleshooting........................ 198
LED Indicator Details......................... 198
Symptoms and Solutions.................. 199
Index........................................... 205
Option ........................................ 207
Installation and Handling Precautions
Précautions d’installation et de manipulation
Precauciones de instalación y manejo
Hinweise zur Aufstellung und Handhabung
Precauzioni relative all’installazione e a come si
maneggia il proiettore
Voorzorgsmaatregelen voor installatie en
behandeling
Forsigtighedsregler ved installation og håndtering
Försiktighetsåtgärder vid montering och hantering
Asennusta ja käsittelyä koskevat varotoimet
安装和搬运注意事项
설치 및 취급 절차
安裝與使用注意事項
設置および取り扱い上のご注意
Installation and Handling Precautions
• Donotinstalltheprojectorinalocationthatisdamp,orwherethere
isalotofdust,oilysmokeortobaccosmoke.Doingsocouldcause
contaminationofopticalcomponentssuchasthelensandthemirror
andmayresultindeteriorationofimagequality.Inaddition,oilcan
degradetheplastic,whichcouldresultinaceiling-mountedprojector
fallingfromitsmounting.
• Donotuseadhesives,lubricants,oils,oralkalinedetergentsfor
maintenanceoftheprojector.Theycouldadheretotheplasticand
deteriorateit,possiblyresultingintheprojectorfallingifitisceiling-
mounted.
• Makesuretoimplementanti-fallmeasuressuchasananti-fallwire
wheninstallingtheprojectorinhighplaces,forexample,installingit
ontheceiling.
ENG Storethisdocumenttogetherwiththe“ImportantInformation”
(booklet)andthe“User’sManual”(CD-ROM).
Avertissement
Précautions d’installation et de manipulation
• N’installezpasleprojecteurdansunendroithumideoutrès
poussiéreux,oudanslequelilseraitexposéàdesfuméescontenant
desparticulesdegraisseoudetabac.Lescomposantsoptiques,
commel’objectifoulemiroir,pourraientêtrecontaminés,etla
qualitédel’imageenseraitaltérée.Deplus,l’huilepeutdétériorerle
plastique,cequipourraitprovoquerlachuteduprojecteurmontéau
plafond.
• N’utilisezpasdecolle,delubriants,d’huilesoudedétergents
alcalinspourl’entretienduprojecteur.Ilspourraientsecollerau
plastiqueetl’endommager,cequipourraitprovoquerlachutedu
projecteurs’ilestmontéauplafond.
• Veillezàmettreenplacedesmesuresantichutetellesqu’uncâble
antichutelorsdel’installationduprojecteurenhauteur,parexemple
auplafond.
Attention
FRA Conservezcedocumentavecles«Informationsimportantes»
(livret)etle«Moded’emploi»(CD-ROM).
Warnung
Hinweise zur Aufstellung und Handhabung
• StellenSiedenProjektornichtaneinemOrtauf,andemerFeuchtigkeit,
Staub,starkenÖldünstenoderZigarettenrauchausgesetztist.Andernfalls
könntendieoptischenBauteile(Objektiv,Spiegel)verschmutztwerden,
waszueinerVerschlechterungderBildqualitätführenwürde.Darüber
hinauskannÖldenKunststoffzersetzen.Dieskanndazuführen,
dasseinanderDeckemontierterProjektorausseinerHalterungfällt.
• VerwendenSiekeineKlebstoffe,Schmiermittel,Öleoderalkalische
ReinigungsmittelfürdieWartungdesProjektors.Siekönntenan
demKunststoffanhaftenundihnbeschädigen.Dieskanndazu
führen,dassderProjektorherunterfällt,wenneraneinerDecke
montiertist.
• AchtenSiedarauf,dassderProjektorbeiderMontageineiner
hohenPosition(z.B.anderDecke)gegenAbsturzgesichertwird(z.
B.miteinemDrahtseil).
Vorsicht
GER BewahrenSiediesesDokumentzusammenmit„WichtigeInforma-
tionen“(Broschüre)unddem„Benutzerhandbuch“(CD-ROM)auf.
Advertencia
Precauciones de instalación y manejo
• Noinstaleelproyectorenunlugarhúmedoodondehayapolvo,
humodetabacoograsa.Dehacerlo,loscomponentesópticos
comolalenteyelespejopodríanensuciarse,afectandoalacalidad
deimagen.Además,lagrasapuededegradarelplástico,locual
podríacausareldesprendimientodelproyectormontadoeneltecho
respectodesumontura.
• Noutiliceadhesivos,lubricantes,aceitesodetergentesalcalinos
paraelmantenimientodelproyector.Talessustanciaspodrían
adherirsealplásticoydeteriorarlo,loquepodríacausarlacaídadel
proyectorsiestámontadoeneltecho.
• Alinstalarelproyectorenlugareselevados,comoporejemploen
eltecho,asegúresedetomarmedidascontralacaídadelaparato,
talescomoelusodeuncabledesujeción.
Atención
SPA Guardeestedocumentojuntoconla“Informaciónimportante”
(folleto)ylas“Instruccionesdeuso”(CD-ROM).
Waarschuwing
Voorzorgsmaatregelen voor installatie en behandeling
• Installeerdeprojectornietineenvochtigeofstofgeruimteofopeen
plaatsmetvettigerookoftabaksrook.Ditkanverontreinigingvan
deoptischecomponentenzoalsdelensendespiegelveroorzaken
enkanverslechteringvandebeeldkwaliteittotgevolghebben.
Daarnaastkunnenvetenoliehetkunststofaantastenwaardooreen
projectordieaanhetplafondisbevestigd,zoukunnenvallen.
• Gebruikvoorhetonderhoudvandeprojectorgeenhechtmiddelen,
smeerolie,andereolieofalkalischeschoonmaakmiddelen.Deze
blijvenmogelijkachterophetkunststof,waardoorditwordt
aangetast.Hierdoorzoudeprojectorkunnenvallenalsdezeaanhet
plafondisgemonteerd.
• Zorgervoordatuvalpreventiemaatregelenneemt,bijvoorbeelddoor
eenveiligheidskabeltegebruiken,alsudeprojectoropeenhoge
plaatsinstalleert,bijvoorbeeldaanhetplafond.
Voorzichtig
NLD Bewaarditdocumentsamenmethetboekje„Belangrijke
informatie”ende„Gebruikershandleiding”(CD-ROM).
Avvertenza
Precauzioni relative all’installazione e a come si maneggia il proiettore
• Noninstallareilproiettoreinluoghiumidioinpresenzadigrandi
quantitatividipolvere,fumooleosoofumoditabacco.Incasocontrario,
sipotrebbeprovocarelacontaminazionedeicomponentiotticiquali
l’obiettivoelospecchio,eprovocareildeterioramentodellaqualità
dell’immagine.Inoltre,l’oliopuòdegradarelaplastica,ilchepotrebbe
risultarenellacadutadiunproiettoremontatoasofttodalsuoattacco.
• Nonutilizzareadesivi,lubricanti,oliodetergentialcaliniperla
manutenzionedelproiettore.Potrebberoaderireallaplasticae
deteriorarla,conlapossibilitàdicausarelacadutadelproiettore,
qualorasiamontatoasoftto.
• Quandosiintendeinstallareilproiettoreinubicazionielevate,ad
esempioquandosiintendeinstallarlosulsoftto,accertarsidi
implementaremisurediprevenzionedellecadute,adesempioun
cavometallicoanticaduta.
Attenzione
ITA Conservarequestodocumentoinsiemea“Informazioniimportanti”
(opuscolo)eal“Manualed’uso”(CD-ROM).
YT1-7519-000 ©CANONINC.2017
Varning
Försiktighetsåtgärder vid montering och hantering
• Monterainteprojektornpåenplatssomärfuktigellerdärdetnns
mycketdamm,oljigrökellertobaksrök.Dettakanförorenaoptiska
komponenter,t.ex.linsochspegel,ochkanledatillförsämrad
bildkvalitet.Dessutomkanoljabrytanedplasten,vilketkanledatill
attprojektornfallernedfrånsittfästeomdenärtakmonterad.
• Användintelim,smörjmedel,oljorelleralkaliskarengöringsmedel
vidunderhålletavprojektorn.Sådanaämnenkanklibbafastpå
plastenochbrytanedellerpåannatsättskadaden,vilketeventuellt
kanledatillattprojektornfallernedomdenärtakmonterad.
• Användalltidenfallskyddskabelellervidtagandra
fallskyddsåtgärdernärdumonterarprojektornpåhögtuppsatta
platser,tillexempelvidmonteringitaket.
Observera
Advarsel
Forsigtighedsregler ved installation og håndtering
• Undladatinstallereprojektorenetsted,dererfugtigt,ellerhvorder
ermegetstøv,oliedampeellercigaretrøg.Ellerskandetresultere
i,atdeoptiskedele,somf.eks.linsenogspejlet,kontamineres,og
billedkvalitetenforringes.Desudenkanolienedbrydeplastikken,
hvilketkanmedføre,atenloftsmonteretprojektorfaldernedfrasin
montering.
• Undladatbrugeklæbestoffer,smøremidler,olierelleralkaliske
rengøringsmidlertilatvedligeholdeprojektoren.Dekansætte
sigfastpåplastikkenogforringedenogmuligvismedføre,at
projektorenfalderned,hvisdenermonteretiloftet.
• Sørgforatbenytteforholdsreglertilforebyggelseaffald,for
eksempelensikkerhedsline,nårprojektorenmonterespå
højtliggendesteder,foreksempelnårdenmonteresiloftet.
Forsigtig
SWE Förvaradethärdokumentettillsammansmed”Viktiginformation”
(häfte)och”Användarhandbok”(CD-ROM).
安裝與使用注意事項
•請勿將投影機安裝在潮濕或者有很多灰塵、油煙或香菸煙霧的地
方。這樣做可能會使得鏡頭與鏡片之類光學組件被污染，而且可
能會造成影像品質劣化。此外，油會讓塑膠劣化，而這可能會使
得安裝在天花板上的投影機從其安裝處掉下來。
•請勿使用黏性、潤滑、油性或鹼性清潔劑保養投影機。它們可能
會附著在塑膠上而令其劣化，如果投影機安裝在天花板上,可能會
造成投影機掉下來。
•將投影機安裝在高處如天花板上時，務必要採取防止掉落的措
施，例如，防止掉落的鋼纜。
FOR 請將此文與“重要資訊”和“使用說明書（CD_ROM）一同保管。
DEN Opbevardettedokumentsammenmed”Vigtigeoplysninger”
(hæfte)og”Brugervejledningen”(CD-ROM).
安装和搬运注意事项
•切勿将投影机安装在潮湿或多尘、有油烟或香烟烟
雾的地方。否则可能会污染光学部件(如镜头和反光
镜)，会导致影像质量下降。此外，油会侵蚀塑料，
降低其性能，有可能会导致安装在天花板上的投影
机从其安装位置掉落。
•请勿使用粘合剂、润滑剂、机油或碱性除垢剂来维
护投影机。这些物质可能会附着在塑料上并对其造
成损坏，如果投影机安装在天花板上，有可能导致
投影机掉落。
•在高处安装投影机时(如将其安装在天花板上)，请
务必采取防坠落措施，如防坠落金属丝。
CHI 请将此文与“使用说明书（手册、CD-ROM)一起保管。
Ꮾᐑ
설치 및 취급 절차
ᔹヱ
• 습기나 먼지, 유연이나 담배 연기가 많은 장소에는 설치하지
마십시오.렌즈나미러등의광학부품에이물질이부착되어화질을
손상시키는원인이될수있습니다.또한오일은플라스틱의품질을
저하시켜천정에장착된프로젝터가떨어질수있습니다.
• 프로젝터의유지관리를위해접착제,윤활제,오일또는알칼리성
세제를 사 용하지 마십시오. 플라스틱에 접착되어 플라스틱을
손상시킬 수 있으며 프로젝터가 천장에 장착된 경우 떨어질 수
있습니다.
• 프로젝터를높은곳에설치할때(예:천장에설치)는낙하방지
와이어와같은낙하방지조치를취하십시오.
〭⺉
KOR 이종이를[중요정보(책자)]및[사용설명서(CD-ROM)]와함께
보관해주십시오.
警告
設置および取り扱い上のご注意
• 湿気やホコリ、油煙やタバコの煙が多い場所には設置しないで
ください。レンズやミラーなどの光学部品に汚れが付着して、
画質を損なう原因になることがあります。また、油により樹脂
が劣化し、天吊り設置の場合に落下するおそれがあります。
• 本機のメンテナンスの際に接着剤、潤滑剤、油、アルカリ性洗
剤などを使用しないでください。付着すると樹脂が劣化し、天
吊り設置の場合に落下するおそれがあります。
• 天吊りのように高所に設置する場合は必ず落下防止ワイヤーな
どの落下防止措置をプロジェクター本体に施してください。
JPN この紙を「重要なお知らせ（冊子）」および「使用説明書（CD-
ROM)」と一緒に保管してください。
Varoitus
Asennusta ja käsittelyä koskevat varotoimet
• Äläasetaprojektoriapaikkaan,jokaonkostea,jossaonpaljon
pölyä,öljyistäsavuataitupakansavua.Sesaattaajohtaaoptisten
osien,kutenobjektiivinjapeilinlikaantumiseen,sekäsaattaa
heikentääkuvanlaatua.Lisäksiöljyvoiheikentäämuovia,
mikävoiaiheuttaakattoonasennetunprojektorinputoamisen
kiinnityksestään.
• Äläkäytäliimoja,voiteluaineita,öljyjätaiemäksisiäpuhdistusaineita
projektorinhuoltamisessa.Nevoivatkiinnittyämuoviinjaheikentää
sitä,mikävoijohtaaprojektorinputoamiseen,josseonkiinnitetty
kattoon.
• Varmista,ettäteetkaikkiputoamisenestävättoimenpiteet,kuten
putoamisenestävävaijeri,kunasennatprojektorinkorkealle,
esimerkiksiasennatsenkattoon.
Huomio
FIN Säilytätämäasiakirjayhdessätuotteiden”Tärkeäätietoa”
(kirjanen)ja”Käyttöopas”(CD-ROM)kanssa.
5
Projector Highlights
High-Resolution LCOS Projection
Projection at 1920x1200 (WUXGA), thanks to high-resolution reflective liquid
crystal on silicon (LCOS) panels.
HDBaseT Input
The projector supports HDBaseT, a next-generation connectivity standard.
HDBaseT offers a convenient connection for carrying high-quality video and audio
signals equivalent to HDMI across distances up to 100 m over a single LAN cable.
This port can also be used to connect the projector to a network.
(P50, P51, P120, P121, P127)
Lens Shift
Lens shift enables motorized image repositioning up, down, left, or right (P47) for
greater freedom in installation.
Motorized Zoom and Focus Adjustment
Efficient setup using motorized zoom and focus adjustment.
Five Lens Units Available
Choose the optimal lens unit for the projection distance or purpose.
HDBaseT terminal
LAN cable
(CAT5e or better;
shielded; not included)
HDMI cable, etc.
HDBaseT transmitter
Projector Highlights
6
Split-Screen Display
Splits the screen for projection of
two separate input signals at once.
(P161)
Edge Blending
Blend the overlapping edges of images
from multiple projectors to make the
overall image more seamless. (P162)
Networked Multi-Projection (NMPJ)
Project images from multiple computers via a network connection.
For details on Networked Multi-Projection (NMPJ), refer to the NMPJ user’s
manual.
LAN
7
Safety Instructions
Safety Instructions
Before installing and operating the projector, read this manual thoroughly.
This projector provides many convenient features and functions. Operating the
projector properly enables you to manage those features and maintain it in good
condition for many years to come.
Improper operation may result in not only shortening the product life, but also
malfunctions, fire hazards, or other accidents.
If your projector does not seem to be operating properly, read this manual again,
check operations and cable connections, and try the solutions in the
“Troubleshooting” section in the back of this manual. If the problem still persists,
contact the Canon Customer Support Center.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS
UNIT IN THE OWNER’S MANUAL.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of
Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Safety Instructions
8
Safety Precautions
WARNING:
• THIS APPARATUS MUST BE GROUNDED.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
•This projector produces intense light from the projection lens. Do not stare
directly into the lens, otherwise eye damage could result. Be especially careful
that children do not stare directly into the beam.
•Install the projector in a proper position. Otherwise it may result in a fire hazard.
•Allowing the proper amount of space on the top, sides, and rear of the projector
cabinet is critical for proper air circulation and cooling of the unit. The diagrams
shown here indicates the minimum space required. If the projector is to be built
into a compartment or similarly enclosed, these minimum distances must be
maintained.
•Do not cover the ventilation slots on the projector. Heat build-up can reduce the
service life of your projector, and can also be dangerous.
•If the projector is unused for an extended time, unplug the projector from the
power outlet.
•Do not project the same image for a long time.
An afterimage may remain on the LCD panels due to the characteristics of the
panels of the projector.
CAUTION ON HANGING FROM THE
CEILING
When hanging the projector from the ceiling, clean the air intake vents and top of
the projector periodically with a vacuum cleaner. If you leave the projector unclean
for a long time, the cooling fans can be clogged with dust, and it may cause a
breakdown or a disaster.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS
SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF
THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY
BECOME DETERIORATED.
SIDE and TOP REAR
At least
50 cm (1.6')
At least
50 cm (1.6')
At least
50 cm (1.6')
At least
50 cm (1.6')
9
Safety Instructions
Safety Instructions
■READ AND KEEP THIS OWNER’S MANUAL FOR LATER
USE.
All the safety and operating instructions should be read before beginning to operate
the product.
Read all of the instructions given here and retain them for later use. Unplug this
projector from the AC power supply before cleaning. Do not use liquid or aerosol
cleaners on the projector. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection of the projector during a lightning storm, or when it is left
unattended or unused for long periods of time, unplug it from the wall outlet. This
will prevent damage due to lightning and power surges.
Do not expose this unit to rain or use near water... for example, in a wet basement,
near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may result
in hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may
fall, causing serious injury to a child or adult, and serious damage to the projector.
Use only with a cart or stand recommended by the manufacturer, or sold with the
projector. Wall or shelf mounting should be carried out in accordance with the
manufacturer’s directions, and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination should be moved with care.
Sudden stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to overturn.
Slots and openings in the rear and front of the cabinet are provided
for ventilation, to insure reliable operation of the equipment and to protect it from
overheating.
The openings should never be covered with cloth or other materials, and the
bottom opening should not be blocked by placing the projector on a bed, sofa, rug,
or other similar surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation such as a book case
unless proper ventilation is provided.
Safety Instructions
10
Never push objects of any kind into this projector through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto the projector.
Do not install the projector near the ventilation duct of air-conditioning equipment.
This projector should be operated using only the type of power source indicated on
the marking label. If you are not sure of the type of power supplied, contact the
Canon Customer Support Center or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric
shock. Do not allow anything to rest on the power cord. Do not locate this projector
where the cord may be damaged by people walking on it.
Do not attempt to service this projector yourself as opening or removing covers
may expose you to dangerous voltages or other hazards. Refer all servicing to
qualified service personnel.
Unplug this projector from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally after following the operating
instructions. Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the projector
to normal operating condition.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a
need for servicing.
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer that have the same characteristics
as the original parts. Unauthorized substitutions may result in fire, electric shock, or
injury.
Upon completion of any service or repairs to this projector, ask the service
technician to perform routine safety checks to determine that the projector is in safe
operating condition.
11
Safety Instructions
Safety Instructions
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in
the country you purchased it.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND
EASILY ACCESSIBLE.
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by
the Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug. This is
a safety feature to ensure the plug fits into the power outlet. Do
not try to tamper with this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
For the U.S. and Canada, LAMP (S) INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING
TO LOCAL, MUNICIPAL, STATE, PROVINCIAL, OR FEDERAL LAWS.
For lamp recycling and disposal information please call 1-800-OK-CANON
for the U.S. and Canada.
Only for European Union and EEA (Norway, Iceland and
Liechtenstein)
These symbols indicate that this product is not to be disposed of
with your household waste, according to the WEEE Directive (2012/
19/EU), the Battery Directive (2006/66/EC) and/or national
legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in
accordance with the Battery Directive, this indicates that a heavy
metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this
battery or accumulator at a concentration above an applicable
threshold specified in the Battery Directive.
This product should be handed over to a designated collection point,
e.g., on an authorized one-for-one basis when you buy a new similar
product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE) and batteries and
accumulators. Improper handling of this type of waste could have a
possible impact on the environment and human health due to
potentially hazardous substances that are generally associated with
EEE. Your cooperation in the correct disposal of this product will
contribute to the effective usage of natural resources.
For more information about the recycling of this product, please
contact your local city office, waste authority, approved scheme or
your household waste disposal service or visit
www.canon-europe.com/weee, or www.canon-europe.com/battery.
Ground
Safety Instructions
12
Federal Communication Commission Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense. The cable with a ferrite core provided with the
projector must be used with this equipment in order to comply with Class A of the
FCC Rules. Use of a shielded cable is required to comply with Class A of FCC
Rules. Do not make any changes or modifications to the equipment unless
otherwise specified in the instructions. If such changes or modifications should be
made, you could be required to stop operation of the equipment.
Warning:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
The cable with a ferrite core provided with the projector must be used with this
equipment in order to comply with Class A .
Use of a shielded cable is required to comply with Class A .
13
Safety Instructions
Safety Instructions
This section describes the safety symbols used in this manual. Important projector
safety information is identified by the following symbols. Always observe the safety
information by these symbols.
Safety Symbols in this Manual
Denotes the risk of death or serious injury from improper
handling if the information is not observed. To ensure safe use,
always observe this information.
Denotes the risk of injury from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of electric shock from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of burns from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes prohibited actions.
Denotes required actions or information that must be observed.
Safety Instructions
14
Precautions for Use
As this section contains important safety-related information, be sure to read the
following carefully beforehand in order to use your projector correctly and safely.
During installation, keep the projector plug easily accessible so that the projector can be
unplugged immediately if necessary, or keep a circuit breaker within reach.
If the following situations occur, turn the power off, remove the power plug from the
power outlet and contact the Canon Customer Support Center. Failure to do so could
cause a fire or result in an electric shock.
•If smoke is emitted
•If an unusual smell or noise is emitted
•If water or other liquid has entered the projector
•If metal or any other foreign material has entered the projector
•If the projector is knocked over or dropped and the cabinet is
damaged
Pay attention to the following points regarding the power source, power plug and
handling of the connector. Failure to do so may cause a fire or electric shock.
•Do not place any objects on the power cord and do not allow it to
become trapped under the projector.
•Do not cover the power cord with a carpet.
•Do not modify or excessively bend, twist, pull, wind, or bundle the
power cord.
•Keep the power cord away from heaters and other sources of
heat.
•Do not use a damaged power cord. If the power cord is
damaged, purchase a replacement from your dealer.
•The power cord included with this projector is for use exclusively
with this product. Do not use this cord for other products.
15
Safety Instructions
Safety Instructions
Pay attention to the following points regarding the power source, power plug and
handling of the connector. Failure to do so may cause a fire or electric shock.
•
Do not use any power source with a voltage other than the voltage
indicated (AC 100–240 V).
•Do not pull the power cord and be sure to hold the power plug or
connector when removing. Incorrect handling may damage the
power cord.
•Do not insert any metal objects into the contact parts of the
power plug or connector.
•Do not remove the power plug or connector with wet hands.
•Insert the power plug and connector securely up to the base.
Additionally, do not use a damaged power plug or an outlet that is
loose.
•When using an extension cord, do not exceed the cord’s rated
capacity.
•Periodically inspect the power plug and outlet and remove any
dust or dirt from between the plug and the outlet.
Installation and Handling Precautions
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
•Do not use the projector where it might get wet, such as outdoors
or by bathtubs or showers.
•Do not place containers containing a liquid on top of the
projector.
•Do not touch the projector itself, the power cord, or the cable if
lightening strikes.
•Do not move the projector until you have switched off the power,
removed the power plug from the power outlet and unplugged
any other cables.
•Unplug the projector before cleaning or maintenance.
•Before you attach or replace a lens unit, be sure to unplug the
power plug of the projector from the power outlet.
Safety Instructions
16
RISK GROUP 3 (RG3) label
17
Safety Instructions
Safety Instructions
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
•Do not remove the cabinet from the projector or disassemble it. The interior
of the projector contains high-voltage components as well as parts that are
hot. If inspection, maintenance or repair is required, contact the Canon
Customer Support Center.
•Do not disassemble or modify the projector (including consumable parts) or
the remote control.
•Do not look directly into the exhaust vents during use.
•Do not insert any object into vents in the projector, such as the air intake vent
or exhaust vents.
•Do not place a pressurized can in front of the exhaust vents. The pressure of
the contents of the can may increase due to heat from the exhaust vents and
this could result in an explosion.
•When cleaning off dust or dirt from projector parts such as the lens or filter,
never use any spray that is flammable. Internal parts that become hot may
ignite and cause a fire.
•Light from the projector is classified as
Risk Group 3 (RG3) according to
IEC 62471:2006.
•Possibly hazardous optical radiation emitted
from this product. Do not look at operating lamp. Eye injury may result. Pay
particular attention to prevent small children from doing so.
•When setting the projector on a high surface for projection, be sure the
surface is flat and stable.
•Do not use the projector on a soft surface such as carpet or sponge mat, etc.
Doing so could cause heat to build up inside the projector and this could
result in a fire.
•For ceiling mounting precautions, refer to the installation manual included
with the ceiling mount (sold separately).
•When hanging the projector from a ceiling, put the projector down on the
floor or a workbench before attaching or replacing the lens unit. Failure to do
so could result in parts falling off the projector and may cause an accident or
personal injury.
Precautions on the Lamp
This projector uses a high-pressure mercury lamp, which must be handled carefully and
correctly as described below.
The mercury lamp has the following characteristics.
•The lamp will gradually become darker over time.
•Impact, abrasion, or use of worn-out lamps may cause lamps to rupture (accompanied
by a loud noise) or burn out.
•Lamps are more likely to rupture after the lamp replacement message is displayed (see
“Replacing the Lamp” (P173)). Replace the lamp with a new one as soon as possible.
•Useful life of lamps varies widely from lamp to lamp and depending on the environment
of use. Some lamps may fail or rupture soon after they are first used.
Safety Instructions
18
Note the following precautions during lamp replacement or when a lamp has ruptured.
Failure to do so could result in an electric shock, personal injury or burns.
•Before replacing the lamp, always unplug the projector and wait at least one
hour.
•If the lamp ruptures, dust and gas (containing mercury vapor) may come out
of the exhaust vents. If this happens, immediately open the windows and
doors to provide ventilation to the room. Ruptured lamps may scatter shards
of glass inside the projector. Contact the qualified technician or Canon
Customer Support Center for cleaning and inspection of the projector interior
and lamp replacement.
•If you accidentally inhale gas from the lamp or get any pieces in your eyes or
mouth, consult a doctor immediately.
Note the following precautions when replacing lamps that stop working. Failure to do so
could result in personal injury.
•If illumination suddenly stops, either when you turn the projector on or after it
has been on for a while, the lamp may have ruptured. In this case, never
attempt to replace the lamp by yourself. Always request service from the
Canon Customer Support Center.
•With ceiling-mounted projectors, the lamp may fall out when you open the
lamp cover, or during replacement. During replacement, stand to the side of
the lamp cover, not directly under it.
Precautions for the Batteries of the Remote
Control
Pay attention to the following points regarding handling of batteries. Failing to do so
could result in a fire or personal injury.
•
Do not heat, short circuit or disassemble the batteries, or place them in a fire.
•Do not attempt to recharge the batteries that are included with the remote
control.
•Remove the batteries when they are flat or when the remote control will not
be used for a long period of time.
•When replacing the batteries, replace both at the same time. Also, do not
use two batteries of a different type at the same time.
•Insert the batteries with the + and - terminals in the correct directions.
•If any liquid from inside the batteries leaks out and contacts your skin, be
sure to wash the liquid off thoroughly.
19
Safety Instructions
Safety Instructions
Pay attention to the following points regarding installation and handling of the projector.
•If the projector will not be used for a long period of time, be sure
to remove the power plug from the power outlet to ensure safety.
Failure to do so presents a risk of fire if dust accumulates on the
plug or outlet.
•Parts of the cabinet around and above the exhaust vents may
become hot during projection. Touching these areas during
operation could cause burns to the hands. Pay particular
attention in preventing young children from touching these parts.
Additionally, do not place any metal objects around or above the
exhaust vents. Due to the heat from the projector, doing so could
cause an accident or personal injury.
•Do not place the projector where it may be exposed to oily smoke
or steam, such as near kitchen counters or humidifiers. Doing so
may cause fire or electric shock.
•Do not place any heavy objects on top of the projector or sit /
stand on it. Pay particular attention to prevent small children from
doing so. The projector may be knocked over and this could
result in damage or a personal injury.
•Do not place the projector on an unstable or slanted surface.
Doing so may cause the projector to fall or be knocked over and
could result in a personal injury.
•Do not place any objects in front of the lens
during projection. Doing so could cause a fire.
•Presenters in front of the projector should
stand where the light does not seem too bright,
and where their shadow does not fall on the screen.
•The projector is provided with a lens shift function to move the
lens up, down, left, and right using the motor. Do not touch the
lens while it is moving. Touching the lens when it is moving may
result in personal injury.
•Before replacing the lens unit, wait at least one hour after the
projector is turned off to allow the projector to cool thoroughly.
Failure to do so could result in a burn or injury.
When handling the lamp, pay attention to the following points.
•Lamps are more likely to rupture once the lamp replacement
message has been displayed. Replace the lamp with a new one
as soon as possible.
•Be sure not to handle the lamp immediately after it has been
used. Be sure to switch off the power and wait for approximately
1 hour for the lamp and the projector to cool down sufficiently.
Failure to do so could result in a burn or personal injury due to
heat from the lamp or projector.
•Be prepared by keeping a spare lamp.
•Dispose of used mercury lamps in accordance with local
regulations.
20
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
•This projector is a precision instrument. Do not knock it over or subject it to
impacts.
•When carrying or holding up the projector after attaching the lens unit, be
sure not to hold the lens. Doing so may cause damage to the lens unit.
•Protection of the projector cannot be guaranteed if used packaging or shock-
absorbent materials are reused. Fragments from shock-absorbent material
may also enter the interior of the projector which could cause a malfunction.
•If transportation is necessary, the lens unit should be removed before
transporting the projector. If the projector is subjected to excessive impacts
during transportation, the lens unit may be damaged.
•Disconnect the cables connected to the projector. Carrying the projector
while the cables are attached may cause an accident.
•Retract the adjustable feet before moving the projector. Leaving the feet
extended may cause damage.
•Do not touch the lens with bare hands. Doing so may result in deterioration
of image quality.
21
For Safe Use
For Safe Use
Pay attention to the following points when installing or using the projector.
•Be careful of condensation.
If the projector is abruptly taken to a warmer location, or if the room
temperature rises abruptly, moisture in the air may condense on the lens and
mirror, causing the image to become blurred.
•Do not install the projector in a location where the temperature is high or low.
Doing so may cause a malfunction. Ranges for the environment of use and
storage are as follows.
•Environment of use: 0°C (32°F) to 40°C (104°F), up to 85% RH
•Storage temperature: -30°C (-22°F) to 60°C (140°F)
•When using the projector at altitudes above 2,300 m (7,545.8'), or when
projecting upward or downward:
Adjust projector installation settings from the menu (P108). Failure to adjust
the settings may shorten the lamp life or damage the lamp.
•Do not install the projector facing the wrong direction. Install the projector so
that it is not tilted left or right by more than 10°. (P25)
•Do not block the air intake or exhaust vents. Blocking the vents may trap
heat inside the projector, which may shorten the useful life of optical
components or other parts and damage the projector.
•Install the projector leaving at least 50 cm (1.6') between air intake/exhaust
vents and walls. Failure to do so may trap heat inside the projector and
damage it.
•Do not place any objects on top of the projector that may change shape or
color due to heat.
•Do not install the projector in a location that is damp, or where there is a lot
of dust, oily smoke or tobacco smoke. Doing so could cause contamination
of optical components such as the lens and the mirror and may result in
deterioration of image quality.
•Do not install the projector near high-voltage electrical power lines or an
electrical power source.
•Clean the air filter regularly. (P171) Dust that accumulates inside over long
periods without cleaning may eventually damage the projector or affect
picture quality.
22
Before Installation
Precautions When Carrying/Shipping the
Projector
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P7 – P21). Also
take the following precautions during installation.
■Do Not Use in the Following Environments
Prepare the projector as described below before carrying it.
• Disconnect the cables connected to the projector. Carrying the
projector with the cables attached may cause an accident.
• Retract the adjustable feet before moving the projector. Leaving
the feet extended may cause damage.
• Do not subject the projector to strong impacts or vibrations.
• Do not strike the projector or subject it to impact. Doing so may
cause a malfunction.
• Do not stand the projector vertically, lean it against another
object, or otherwise place it in an unstable state. The projector
may be damaged if it tips over.
• Locations with excessive humidity, dust, oily smoke or tobacco
smoke
Adhesion to the lens, mirrors or other optical parts may reduce image
quality.
• Near high-voltage power lines or sources of electrical power
This may cause malfunction.
• On soft surfaces such as carpets or cushioned mats
This may cause a fire or damage the projector.
• Locations with excessive temperature or humidity
This may damage the projector. Acceptable ranges for operating and
storage temperature and humidity are as follows.
* Operating temperature and humidity applies to when the projector
is projecting or in standby mode.
Operating temperature Operating humidity Storage temperature
0°C (32°F) – 40°C (104°F)
Up to 85%
-30°C (-22°F) – 60°C (140°F)
23
Before Installation
Before Installation
■Do Not Touch the Lens with Bare Hands
■Allow a 30 Min. Warm Up before Focus Adjustment (P59), if Possible
The focus position may not stabilize immediately after startup, due to lamp heat.
When adjusting focus, it is also helpful to use the test pattern (10) (P115, P187).
■Install at a Sufficient Distance from Walls and Other Obstructions
■Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on
the projector lens and mirror, causing the image to become blurred. Wait until the
condensation has evaporated for the image projected to return to normal.
■At Altitudes above 2,300 m (7,545.8'), Adjust the Settings
Projector settings must be adjusted when using the projector at altitudes of 2,300 m
(7,545.8') or higher. Specifically, refer to instructions for [Fan mode] (P108) in the
[Install settings] menu.
• Do not touch the lens with bare hands. Any smudges or
fingerprints on the lens may affect image quality.
If the air intake or exhaust
vent is blocked, heat will
accumulate inside the
projector, possibly resulting in
a shortened projector lifetime
or a malfunction.
Similarly, do not install in
narrow, enclosed spaces with
poor ventilation. Install in a
well-ventilated location.
Ensure a minimum clearance of 50 cm (1.6 ft.) above, on both
sides, and behind the projector, as shown below.
Exhaust vent
Air intake vent
Warmed
airflow
50cmà»è„
At least
50 cm (1.6')
At least
50 cm (1.6')
At least
50 cm (1.6')
At least
50 cm (1.6')
Before Installation
24
■When Using Mounted on the Ceiling
When the projector is used mounted on the
ceiling or installed in a high location, it is
necessary to periodically clean the air
intake and exhaust vents, and the area
around the air filter. Dust that accumulates
in intake or exhaust vents may impair
ventilation, raising the temperature inside
and posing a risk of damage or fire. Use a
vacuum cleaner or similar means to
remove dust from the intake vent and
exhaust vent.
25
Before Installation
Before Installation
■Install Facing in the Correct Direction
There are no options for installing the projector other than the ceiling attachment.
• The projector can be installed facing any direction, as shown
below. However, projection upward or downward may shorten the
useful life of the lamp. [Install settings] of the projector must also
be adjusted.
• For upward or downward projection, refer to instructions for
[Vertical projection] (P108) in the [Install settings] menu.
• Do not attempt to install the projector for upward or downward
projection by yourself. Always request installation by a qualified
technician or the Canon Customer Support Center.
Upward
projection:
Inclination of the
projector should
be no more than
10° from the
vertical axis.*
Downward
projection:
Inclination of the
projector should
be no more than
10° from the
vertical axis.
*
If installing the projector
on the floor or hanging
from the ceiling, the left /
right inclination of the
projector should be no
more than 10°.*
Do not use the
projector standing
on its side.
This may
damage the lamp.*
10°
10° 10°
10° 10°
10°
* Failure to do so may damage the lamp.
Before Installation
26
Copyright Notice
Please note that enlarging or reducing the size of an image for commercial
purposes or public presentation may infringe on the legally protected copyright
or the copyright holder of the original material.
Ensure Network Security
Take measures to ensure network security. Note that Canon is not liable in any
way for direct or indirect loss from network security incidents, such as
unauthorized access.
Before using the projector, configure the appropriate projector, computer, and
network security settings.
Install the projector in a network protected by a firewall or other security
measures. Do not connect it directly to the Internet.
About Trademarks
•Ethernet is a registered trademark of Xerox Corporation.
•Microsoft, Windows, Windows Vista, Windows 7, Windows 8, Windows 8.1
and Windows 10 are registered trademarks or trademarks of Microsoft
Corporation in the United States and / or other countries.
•Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the
United States and / or other countries.
•HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
•PJLink is a registered trademark of JBMIA and pending trademark in some
countries.
•PJLink is a registered trademark, or an application has been submitted for
trademark, in Japan, the United States and / or other countries or regions.
•AMX is a trademark of AMX Corporation.
•Crestron®, Crestron RoomView®, and Crestron Connected™ are registered
trademarks of Crestron Electronics, Inc.
•HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT
Alliance.
•All other trademarks are the property of their respective owners.
27
Open Source Software
Open Source Software
The product contains Open Source Software modules. For details, refer to the third-
party software license file “Third-Party Software” in the License folder of the user’s
manual CD-ROM. Each module’s license conditions are also available in the same
folder.
■Software under the GNU General Public License Version 2
Contained programs are free software; you can redistribute them and/or modify
them under the terms of the GNU General Public License attached to each copy of
the program.
Each program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. Please see “NO WARRANTY” and
“NO SUPPORT” stated below. For more detail, please see full text of the GNU
General Public License.
NO WARRANTY
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN
WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY
MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NO SUPPORT
Canon Inc., and all its subsidiaries or its dealers do not make any support service
regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall
not respond to any questions or enquiries, from you or any other customers,
regarding the source code.
28
Before Use
Included Accessories
Before use, make sure the following items are included in the package.
• Remote control • Batteries for the remote control
(AAA size x2)
(part No.: RS-RC04)
Optional remote controls are also
available (RS-RC05). The RS-RC05
can also be used as a wired remote.
(P38)
• Computer cable (1.8 m / 5.9')
(mini D-sub 15-pin / mini D-sub 15-pin)
• Power cord
(1.8 m / 5.9')
For Continental
Europe
• User’s Manual (CD-ROM)
For the U.S.A.
and Canada
• Important Information
• Warranty Card
29
Before Use
Before Use
Part Names
Projector
■Rear Side
Terminals and
connectors
Infrared remote receiver
(P38)
Lens unit (sold separately)
Air intake vent
Power cord connector (P52)
Side control (P30)
Air filter frame (P172)
Anti-theft lock hole
An anti-theft wire cable (not included) can be connected.
Do not block the air intake.
Doing so may cause a
malfunction.
Exhaust vent
Infrared remote receiver (P38)
Do not block the air exhaust.
Doing so may cause a
malfunction.
Lamp cover
Before Use
30
■Bottom Side
Side Control
Adjustable feet (P40)
Bolt holes for installation of
ceiling attachment
(1) POWER button (P53, P71)
Turns the projector on or off.
(2) MENU button (P78)
Displays a menu on the screen.
(3) LENS button
Each time the button is pressed,
the screen changes to focus
adjustment (P59), zoom (image
size) adjustment (P60), or lens shift
(image position) adjustment (P61).
To adjust, use the [ ] / [ ] or the
[ ] / [ ] buttons.
(4) INPUT button (P56)
Switches the input signal.
(5) Pointer / VOL buttons (P79)
Up, down, left, or right in menu
navigation or other operations.
Adjust the sound volume.
[ ] VOL+ button: Increases the
volume.
[ ] VOL– button: Decreases the
volume.
Selects the upper, lower, left or
right item in the menu.
(6) OK button (P79)
Determines the item selected from
the menu.
(1)
(2)(4)(5)
(6) (3)
31
Before Use
Before Use
LED Indicators
The projector status is shown by the LED indicators (off / lit / flashing).
•POWER ON (green) : Lights up or flashes under normal
conditions when the power is on.
•STAND BY (red) : Lights up or flashes during standby or
when the projector is shut down.
•WARNING (red) : Lights up or flashes when an error
occurs.
•LAMP (orange) : Lights up or flashes when a problem
occurs with the lamp or lamp cover.
•TEMP (red) : Lights up or flashes when the internal
temperature is high.
Before Use
32
■LED Indicator Displays
The LED indicators flash or illuminate to indicate the operating status of the
projector.
Legend: Example of when the POWER ON indicator is on; : Off : Lit : Flashing
LED indicator
Operating status
POWER
ON
(green)
STAND
BY
(red)
WARNING
(red)
LAMP
(orange)
TEMP
(red)
Not plugged in.
In standby mode.
Power is on.
Transitioning from standby mode to
power on.
Cooling down while transitioning from
power on to standby mode or power
management mode.
In power management mode, with the
lamp off.
Nearly time to replace the lamp (in
standby mode).
Nearly time to replace the lamp (during
projecting).
Internal temperature is high (in standby
mode).
Internal temperature is high (during
projecting).
A lamp error has occurred.
A temperature error has occurred.
The lamp cover is open.
Another error has occurred.
A flashing LAMP indicator means that it is almost time to replace
the lamp. Prepare a replacement lamp.
33
Before Use
Before Use
Input Terminal
(1) Terminal for wired remote control (REMOTE) (P38)
This terminal is used to connect the optional remote control (RS-RC05) using a
cable.
(2) AUDIO IN terminal (AUDIO IN) (P49, P50, P51)
Terminals for audio input. Audio supplied to these terminals is played through
the internal speaker when you select [Audio in] as the source audio terminal
for the selected source video. (P119)
(3) AUDIO OUT terminal (AUDIO OUT) (P49, P50, P51)
Outputs the audio to external AV equipment. This outputs the audio signal that
corresponds to the projected image signal.
(4) USB port (P157)
Connects a USB flash drive. Used for projection of images on a USB flash
drive, or for firmware updates.
(5) DVI-I terminal ( DVI-I) (P49)
Connects the external monitor output from a computer.
Receives digital PC signal (Digital PC).
A VGA-DVI-I cable can also be used to receive analog computer signals
(Analog PC-1).
(6) ANALOG PC-2 / COMPONENT input terminal ( / COMPONENT)
(P50, P51)
Receives the analog PC signal (Analog PC-2).
A component cable can be used to receive the component image signal
(Component).
(7) HDMI terminal (HDMI) (P50, P51)
Receives digital video signals (HDMI).
Carries both video and audio signals across a single cable.
(8) LAN port (P127)
Connects the LAN cable (shielded twisted pair).
Used to connect the projector to a network.
(9) HDBaseT terminal (P50, P51, P127)
Receives HDBaseT input including digital video and audio signals.
A single LAN cable (shielded twisted pair) can be used for both video and
audio input.
This port can also be used to connect the projector to a network.
(4)
(1) (2)
(5) (6) (7) (8) (9) (10)
(3)
35
Before Use
Before Use
Remote Control
The projector can be operated using buttons on the remote control or the side
control on the projector.
(1) POWER button (P53, P71)
Turns the projector on or off.
(2) FOCUS button (P59)
Adjusts focusing.
[ ] / [ ] buttons:
Moves the focus position further away.
[ ] / [ ] buttons:
Moves the focus position nearer.
(3) ASPECT button (P65, P91)
Changes the aspect ratio mode.
(4) D.SHIFT/KEYSTONE button (P67)
Corrects keystone distortion.
The [Keystone] setting enables both
horizontal/vertical keystone correction
(by adjusting top/bottom/left/right
length) and corner correction.
•Moves the image up, down, left, or
right when the screen aspect setting
is [16:9 D. image shift] or [4:3 D.
image shift] is selected. (P64, P65)
•To move the image, use the [ ] / [ ]
or the [ ] / [ ] buttons.
(5) D.ZOOM button (P75)
Zooms the image in or out digitally.
[ ] button: Zooms the image in (up to
12x).
[ ] button: Zooms the image out (1x
minimum).
[ ] / [ ] / [ ] / [ ] buttons:
Move the zoom-in location.
(6) FREEZE button (P72)
Freezes the projected image.
(7) IMAGE button (P70)
Switches the image mode (image
quality).
(8) INPUT button (P56)
Switches the input signal.
(1)
(2)
(3)
(4)
(5)
(7)
(6)
(8)
36
Before Use
(9) LENS-SHIFT button (P61)
Moves the lens up, down, left, or right.
[ ] / [ ] / [ ] / [ ] buttons:
Moves the image.
(10) ZOOM button (P60)
Adjusts the image size.
[ ] / [ ] buttons:
Increase the image size.
[ ] / [ ] buttons:
Decrease the image size.
(11) AUTO PC button (P58)
Adjusts tracking etc. automatically in
accordance with the signal from a computer
when the analog PC input is selected.
(12) OK button (P79)
Determines the item selected from the
menu.
(13) Pointer buttons (P79)
Selects the upper, lower, left or right
item in the menu. Also used to assign a
channel to the remote control.
(14) MENU button (P78)
Displays a menu on the screen. Also
used to assign a channel to the remote
control. (P119)
(15) VOL button (P74)
Adjusts the sound volume.
[+] button: Increases the volume.
[–] button: Decreases the volume.
(16) P-TIMER button
Cannot be used on this projector.
(17) MUTE button (P74)
Mutes the sound.
(18) BLANK button (P72)
Temporarily blacks out the image.
(19) LAMP button (P102)
Displays the power saver settings
screen, where you can adjust the lamp
mode (Full power / Power saver)
(P102), set the power management
(P121) and specify the network standby
settings (P131).
(20) GAMMA button (P98)
Adjusts the gamma of the image.
[ ] button:
Corrects dark parts of the image so that
they are easier to see.
[ ] button:
Corrects bright parts of the image so
that they are easier to see.
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(9)
(10)
37
Before Use
Before Use
Preparing the Remote Control
■Installing Remote Control Batteries
• If buttons on the remote control are inoperative when you attempt to operate the
projector, replace the batteries with new ones.
• Do not drop the remote control or subject it to impact.
• Do not spill any liquids on the remote control. Doing so may cause a malfunction.
Pay attention to the following points when handling the batteries.
Failing to do so could result in a fire or personal injury.
• Do not heat, short circuit or disassemble the batteries, or place
them in a fire.
• Do not attempt to recharge the batteries that are included with the
remote control.
• Remove the batteries when they are flat or when the remote control
will not be used for a long period of time.
• When replacing the batteries, replace both at the same time. Also,
do not use two batteries of a different type at the same time.
• Insert the batteries with the + and - terminals in the correct
directions.
• If any liquid from inside the batteries leaks out and contacts your
skin, be sure to wash the liquid off thoroughly.
3Close the
compartment lid.
Slide the lid until you
hear a click to
securely close it.
2Insert batteries.
Insert 2 new AAA
batteries in the
compartment with the
+ and – terminals
positioned correctly.
1Open the battery
compartment lid.
Slide the lid while
pressing it down.
Before Use
38
■Remote Control Operating Range
The remote control is an infrared type. Point it at the infrared remote receiver on the
front or rear of the projector to operate it.
■Using an Optional Wired Remote (RS-RC05)
To use a wired remote control with the projector, use the RS-RC05, sold separately.
Use a cable with a ø3.5 mm stereo mini jack (not included).
• Use the remote control no further than approximately 8 m (26.3') from the projector.
• Use the remote control within an angle of 25° in any direction from directly in front of the
infrared remote receiver.
• The remote control may be inoperative if there is an obstacle between the remote
control and the projector or the infrared remote receiver on the projector is exposed to
direct sunlight or strong light of lighting equipment.
• When you use 2 or more projectors at the same time, you can change the channel
settings to prevent the 2 remote controls from interfering with each other. (P119)
• Infrared operations cannot be performed if a cable is connected to the projector or the
remote control.
• Use a cable with a ø3.5 mm stereo mini jack (not included) with a length of 30 m (98.4')
or less.
25°
25°
8 m (26.3')
8 m (26.3')
25°
25°
ø3.5 mm stereo mini jack
cable (not included)
Terminal for wired
remote control
Remote control
(RS-RC05)
39
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced Guide
Using Menus
Menu Configuration
Menu Description
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
Basic Guide
40
Installation Procedure
Before setting up the projector, be sure to read “Before Installation” (P22).
Setting Up the Projector
■Positioning the Projector in Front of the Screen
Place the projector in front of the screen.
■Floor Installation
To adjust the projection position when the projector is installed on the floor, use the
lens shift function (P47, P61) to adjust up / down / left / right. You can also use the
adjustable feet to incline the projector upward by up to 6°.
For information about the relationship between screen size and projection distance,
refer to page 43.
■Installation Tilted Upward
To correct keystone distortion when the projector is tilted upward (using adjustable
feet, for example), perform keystone correction (P67) or corner adjustment (P68).
• To avoid keystone distortion, install the
projector so that it is at right angles to the
screen.
• The screen must not be exposed to direct
sunlight or light from lighting equipment. In
a bright room, it is recommended that
lights be turned off, curtains be drawn, and
other steps taken to make the screen
easier to see. Optical axis
Screen
Lens shift Adjustable feet
41
Installation Procedure
Basic Guide Installation Procedure
■Installation on High Surfaces
For projection from a shelf or other high surface, the projector can be installed
upside-down and the projected image inverted.
■Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (ceiling mounting) with it turned upside
down or place it behind the screen (rear projection) if you use a translucent screen.
Make sure to use the optional ceiling attachment. For the ceiling attachment, refer
to “Option” (P207). For details, refer to the assembly and installation manual
provided with the ceiling attachment.
When setting the projector on a
high surface for projection, be sure
the surface is flat and stable.
Failure to do so poses a risk of the
projector falling and causing
accidents or injury.
Ceiling mounting Rear projection
Installation Procedure
42
Mounting the Projector on the Ceiling
You can mount the projector on the ceiling.
The ceiling attachment (part No.: RS-CL11)
is required in order to mount the projector on
the ceiling. Depending on the installation
environment, an extension pipe
(part No.: RS-CL08 or RS-CL09) may also
be required. Contact the Canon Customer
Support Center for more detailed
information.
If you mount the projector on the ceiling, you have to invert the projected image by
selecting [Image flip H/V] from the menu. (P105)
• Make sure to use the optional ceiling attachment.
• You should never install the ceiling attachment by yourself.
43
Installation Procedure
Basic Guide Installation Procedure
Relationship Between Image Size and
Projecting Distance
The projected image size is determined by the distance between the projector and
the screen (projection distance) as well as the zoom. Refer to the following table
and decide the distance between the projector and screen.
WUX6500
• H1 and H2 are the distances when lens shift is the default value below.
• Standard Zoom Lens / Long Zoom Lens / Ultra Long Zoom Lens / Wide Zoom Lens:
+50% (up / down), 0% (left / right)
Short Fixed Lens: 0% (up / down / left / right)
Lens unit
Diagonal
when
16:10
Image size (cm)
Projection
distance
m (feet)
Distance from
optical axis
when projection
is perpendicular
to screen (cm)
16:10 16:9 4:3 16:10
Width Height Width Height Width Height
Wide
limit
Tele
limit H1 H2
Standard
Zoom Lens
RS-IL01ST
40 86 54 89 50 81 61 1.3
(4.3)
1.9
(6.2) 54 0
60 129 81 133 75 122 91 1.9
(6.2)
2.9
(9.5) 81 0
80 172 108 177 100 163 122 2.6
(8.5)
3.9
(12.8) 108 0
100 215 135 221 125 203 152 3.2
(10.5)
4.8
(15.7) 135 0
150 323 202 332 187 305 229 4.8
(15.7)
7.2
(23.6) 202 0
200 431 269 443 249 406 305 6.4
(21.0)
9.6
(31.5) 269 0
250 538 337 553 311 508 381 8.0
(26.2)
12.1
(39.7) 337 0
300 646 404 664 374 610 457 9.6
(31.5)
14.5
(47.6) 404 0
350 754 471 775 436 711 533 11.3
(37.1)
16.9
(55.4) 471 0
400 862 538 886 498 813 610 12.9
(42.3)
19.3
(63.3) 538 0
450 969 606 996 560 914 686 14.5
(47.6)
21.7
(71.2) 606 0
500 1077 673 1107 623 1016 762 16.1
(52.8)
24.1
(79.1) 673 0
550 1185 740 1218 685 1118 838 17.7
(58.1)
26.6
(87.3) 740 0
600 1292 808 1328 747 1219 914 19.3
(63.3)
29.0
(95.1) 808 0
16:9 / 16:10
Screen size
(diagonal)
Height
Width
4:3
Height
Width
Optical axis when projection is
perpendicular to screen
Screen
H2
H1
Installation Procedure
44
Long
Zoom Lens
RS-IL02LZ
40 86 54 89 50 81 61 1.9
(6.2)
3.2
(10.5) 54 0
60 129 81 133 75 122 91 2.8
(9.2)
4.8
(15.7) 81 0
80 172 108 177 100 163 122 3.8
(12.5)
6.4
(21.0) 108 0
100 215 135 221 125 203 152 4.7
(15.4)
8.0
(26.2) 135 0
150 323 202 332 187 305 229 7.1
(23.3)
12.1
(39.7) 202 0
200 431 269 443 249 406 305 9.5
(31.2)
16.1
(52.8) 269 0
250 538 337 553 311 508 381 11.9
(39.0)
20.2
(66.3) 337 0
300 646 404 664 374 610 457 14.2
(46.6)
24.2
(79.4) 404 0
350 754 471 775 436 711 533 16.6
(54.5)
28.3
(92.8) 471 0
400 862 538 886 498 813 610 19.0
(62.3)
32.3
(106.0) 538 0
450 969 606 996 560 914 686 20.9
(68.6)
35.6
(116.8) 606 0
500 1077 673 1107 623 1016 762 23.8
(78.1)
40.4
(132.5) 673 0
550 1185 740 1218 685 1118 838 26.1
(85.6)
44.5
(146.0) 740 0
600 1292 808 1328 747 1219 914 28.5
(93.5)
48.5
(159.1) 808 0
Short
Fixed Lens
RS-IL03WF
40 86 54 89 50 81 61 0.7 (2.3) 27 27
60 129 81 133 75 122 91 1.0 (3.3) 41 41
80 172 108 177 100 163 122 1.4 (4.6) 54 54
100 215 135 221 125 203 152 1.7 (5.6) 68 68
150 323 202 332 187 305 229 2.6 (8.5) 101 101
200 431 269 443 249 406 305 3.4 (11.2) 135 135
250 538 337 553 311 508 381 4.3 (14.1) 168 168
300 646 404 664 374 610 457 5.2 (17.1) 202 202
Lens unit
Diagonal
when
16:10
Image size (cm)
Projection
distance
m (feet)
Distance from
optical axis
when projection
is perpendicular
to screen (cm)
16:10 16:9 4:3 16:10
Width Height Width Height Width Height
Wide
limit
Tele
limit H1 H2
45
Installation Procedure
Basic Guide Installation Procedure
Ultra Long
Zoom Lens
RS-IL04UL
60 129 81 133 75 122 91 4.6
(15.1)
9.0
(29.5) 81 0
80 172 108 177 100 163 122 6.1
(20.0)
12.0
(39.4) 108 0
100 215 135 221 125 203 152 7.6
(24.9)
14.9
(50.2) 135 0
150 323 202 332 187 305 229 11.4
(37.4)
22.3
(77.3) 202 0
200 431 269 443 249 406 305 15.2
(49.7)
29.8
(97.8) 269 0
250 538 337 553 311 508 381 18.9
(62.0)
37.2
(122.0) 337 0
300 646 404 664 374 610 457 22.7
(74.5)
44.6
(146.3) 404 0
350 754 471 775 436 711 533 26.4
(86.6)
52.0
(170.6) 471 0
400 862 538 886 498 813 610 30.2
(99.1)
59.4
(194.9) 538 0
450 969 606 996 560 914 686 34.0
(111.5)
66.8
(219.2) 606 0
500 1077 673 1107 623 1016 762 37.7
(123.7)
74.2
(243.4) 673 0
550 1185 740 1218 685 1118 838 41.5
(136.2)
81.6
(267.7) 740 0
600 1292 808 1328 747 1219 914 45.2
(148.3)
89.0
(292.0) 808 0
Lens unit
Diagonal
when
16:10
Image size (cm)
Projection
distance
m (feet)
Distance from
optical axis
when projection
is perpendicular
to screen (cm)
16:10 16:9 4:3 16:10
Width Height Width Height Width Height
Wide
limit
Tele
limit H1 H2
Installation Procedure
46
Wide Zoom
Lens
RS-IL05WZ
40 86 54 89 50 81 61 0.9
(3.0)
1.3
(4.3) 54 0
60 129 81 133 75 122 91 1.3
(4.3)
1.9
(6.2) 81 0
80 172 108 177 100 163 122 1.7
(5.6)
2.6
(8.5) 108 0
100 215 135 221 125 203 152 2.2
(7.2)
3.2
(10.5) 135 0
150 323 202 332 187 305 229 3.2
(10.5)
4.9
(16.1) 202 0
200 431 269 443 249 406 305 4.3
(14.1)
6.5
(21.3) 269 0
250 538 337 553 311 508 381 5.4
(17.7)
8.1
(26.6) 337 0
300 646 404 664 374 610 457 6.5
(21.3)
9.7
(31.8) 404 0
350 754 471 775 436 711 533 7.5
(24.6)
11.4
(37.4) 471 0
400 862 538 886 498 813 610 8.6
(28.2)
13.0
(42.7) 538 0
450 969 606 996 560 914 686 9.7
(31.8)
14.6
(47.9) 606 0
500 1077 673 1107 623 1016 762 10.8
(35.4)
16.3
(53.5) 673 0
550 1185 740 1218 685 1118 838 11.8
(38.7)
17.9
(58.7) 740 0
600 1292 808 1328 747 1219 914 12.9
(42.3)
19.5
(64.0) 808 0
Lens unit
Diagonal
when
16:10
Image size (cm)
Projection
distance
m (feet)
Distance from
optical axis
when projection
is perpendicular
to screen (cm)
16:10 16:9 4:3 16:10
Width Height Width Height Width Height
Wide
limit
Tele
limit H1 H2
47
Installation Procedure
Basic Guide Installation Procedure
Lens Shift Function
The projector includes a lens shift function. Operation of the buttons slides the lens
up, down, left, and right, moving the image position. For instructions, refer to
“Adjusting the Image Position” (P61).
The amount of lens shift is indicated as a percentage relative to the image height
and width.
The table below shows the lens shift for each lens.
Lens unit WUX6500
Standard Zoom Lens
(RS-IL01ST)
Up (1): +55%
Down (2): -15%
Left / right (3): ±10%
Long Zoom Lens
(RS-IL02LZ)
Ultra Long Zoom Lens
(RS-IL04UL)
Wide Zoom Lens
(RS-IL05WZ)
Short Fixed Lens
(RS-IL03WF)
Up (1): +5%
Down (2): -5%
Left / right (3): ±2%
90
90
Amount movable in
up/down direction
At maximum upward lens shift At maximum downward lens shift
(1)
(2)
90°
90°
(3)
Amount movable
in left/right
direction
At maximum leftward lens shift At maximum rightward lens shift
(3)
Installation Procedure
48
Area Outside the Lens Shift Range
With the Standard Zoom Lens, Long Zoom Lens, Ultra Long Zoom Lens, and Wide
Zoom Lens, when the shift exceeds 44% in the upward direction, the amount of
available shift in the left / right directions decreases. When the lens is shifted
upward to the maximum (1), the amount of available shift in the left / right direction
is ±2%.
The more you shift the Short Fixed Lens up or down, the less you can shift it left or
right. At the position of maximum lens shift upward or downward, the lens cannot
be shifted left or right.
Amount of shift relative
to projected image width
Amount of shift relative to
projected image width
Amount of shift
relative to projected
image height
(1) Shift range
Projected image
Area where shift is
not possible
2% of projected
image width
2% of projected
image width
Area where shift is
not possible
Shift range
Projected image
5% of projected
image height
5% of projected
image height
49
Basic Guide Connection Procedure
Connection Procedure
Connecting a Computer
Before connecting the projector to other equipment, turn off both the projector
and the other equipment.
Amplified
speakers
Mini jack RCA terminal
Audio cable
(not included)
AUDIO OUT
terminal
DVI-I terminal
AUDIO IN 1
terminal
Audio cable
(not included)
DVI-D-sub 15 cable
(not included)
DVI-I cable
(not included)
AUDIO output
terminal
Monitor output
terminal
(Mini D-sub 15-pin)
Monitor output
terminal
(DVI terminal)
Computer
Audio cable
(not included)
Connection Procedure
50
Connecting a Computer (continued)
Computer
AUDIO output
terminal
Monitor output terminal
(Mini D-sub 15-pin)
Audio cable
(not included)
Computer cable
(not included) or
BNC cable
(not included)
HDBaseT terminal
HDMI terminal
AUDIO IN 2
terminal
ANALOG PC-2 /
COMPONENT terminal
LAN cable
(CAT5e or better; shielded;
not included)
HDBaseT
transmitter
HDMI cable
(not included)
HDMI cable
(not included)
HDMI terminal
Computer
Mini D-sub 15-pin - BNC
terminal converter cable
(not included)
51
Connection Procedure
Basic Guide Connection Procedure
Connecting AV Equipment
Amplified
speakers
Mini jack
RCA
terminal Mini jack
RCA
terminal
AV equipment
D terminal
RCA component
terminal
Audio
cable
(not
included)
Audio
cable
(not
included)
D terminal
plug - RCA
plug
component
conversion
cable (not
included)
RCA plug -
RCA plug
component
cable (not
included)
Component cable
(not included)
HDBaseT terminal
HDMI terminal
AUDIO IN 2
terminal
ANALOG PC-2 /
COMPONENT terminal
AUDIO OUT
terminal LAN cable
(CAT5e or better; shielded;
not included)
HDBaseT
transmitter
HDMI terminal
AV equipment
HDMI cable
(not included)
HDMI cable
(not included)
Connection Procedure
52
Plugging the Projector In
Connect the power cord to the projector and plug it in.
Notes on HDBaseT
• Use a shielded cable rated at CAT5e or better.
• Maximum transmission distance is 100 m.
• However, maximum transmission distance may be shorter in some environments.
• Do not use the LAN cable when it is coiled or bundled.
• Inserting or removing the LAN cable during projection may cause noise.
• Connectivity with all HDBaseT transmitters on the market is not guaranteed.
• Some HDBaseT transmitters may not enable correct projection when used to connect
source equipment to the projector.
Insert the power plug and connector securely up to the base.
• After turning off the projector, wait at least 5 minutes before turning it on again. Turning
the projector on immediately after turning it off may shorten the lamp life.
• Unplug the power cord when the projector is not in use.
53
Basic Guide Projection Procedure
Projection Procedure
Step 1 Turn the Projector On
1Check the connection between the projector and the computer or AV
equipment. (P49 - P51)
For instructions on connecting the power cord, refer to “Plugging the Projector
In” (P52).
2Press the POWER button.
The [POWER ON] indicator initially flashes green, after which it remains lit.
The countdown window is displayed for approximately 20 seconds, and then
the projection is started. Press the OK button to hide the countdown window.
3Turn on the computer or AV equipment power.
• Network functions are not available for the first 40 seconds after startup.
• A window appears when the projector is turned on for the first time. You can select a
language to be used by the projector for displaying menus and messages in the
window. Select the desired language with the pointer buttons and press the OK button.
(P54)
You can change the language from the menu at a later time. (P123)
Remote control Projector
Changing Operations When Projector is Turned On
You can change operations when the projector is turned on as follows.
•You can turn on the projector by connecting the power cord, without
pressing the POWER button. (P122)
•You can change the countdown window. (P118)
•You can skip the countdown window. (P118)
When the Projector Is Left Idle
If no signal is received, the power management feature automatically turns off
the projector after a certain period of inactivity (by the factory default, 15
minutes). (P121)
54
Projection Procedure
■When the Language Selection Screen Appears
A screen appears when the projector is turned on for the first time. You can select a
language to be used by the projector for displaying menus and messages in the
window. Select the desired language with the pointer buttons and press the OK
button.
You can change the language from the menu at a later time. (P123)
If the language selection screen is out of focus, adjust the focus. (P59
)
■When the Password Input Screen Appears
If you have set a password, the password input screen appears. Enter your
password. (P124)
■When “No signal” Appears
With a notebook computer, the user must turn on the external monitor output. (P55)
Press the INPUT button to select the input signal. (P56)
■When Notebook Computer Screen Does Not Appear
Set your notebook computer to output signals to an external monitor. For more
details, refer to “Changing Notebook Computer Screen Output” (P55).
■Adjusting Image
•Set the display resolution of the computer to the highest resolution or the
resolution closest to that setting. (P57)
•Use the auto PC function to adjust shift in computer image or the flickering of the
screen. (P58)
•Adjust the size of projected images by zooming. For the Standard Zoom Lens,
Long Zoom Lens, Ultra Long Zoom Lens, and Wide Zoom Lens, use optical zoom
(P60). For the Short Fixed Lens, use digital zoom (P106).
•Correct any keystone distortion by pressing the D.SHIFT/KEYSTONE button. (P67)
•Select the aspect ratio of the projected image (screen aspect) or a screen mode
(aspect) according to the aspect ratio of the screen, type of input image signal
etc. (P63 – P66)
•Select an image mode depending on the projected image. (P70)
The image can also be adjusted by projecting a test pattern (P187).
Remote control Projector
An item highlighted in orange will be selected.
Projection Procedure
55
Basic Guide Projection Procedure
Changing Notebook Computer Screen Output
For projection from a notebook computer, the computer settings must be adjusted
to switch display output.
This operation is not required for a desktop computer.
■Turning on External Monitor Output
You can turn on the external monitor output via keyboard operation.
To turn on the external monitor output with most computers, press the function key
([F1] to [F12]) which is marked with the external monitor icon while holding down
the [Fn] key.
• The function key you use and the method used to turn on the external monitor output
vary depending on the model. For details, see the manual for your notebook computer.
• With Windows 10, Windows 8.1, Windows 8 or Windows 7, you can turn on image
output by holding down the Windows logo key and pressing the [P] key.
While pressing key press a key such as or .
56
Projection Procedure
Step 2 Select an Input Signal
Select the input signal in the [Input] menu when you want to project a digital PC or
AV equipment signal, or to switch between inputs when multiple computers or
multiple sets of AV equipment are connected.
Skip this step if you have not changed the input signal since the last projection.
1Press the INPUT button to display the window shown below.
The currently active input signal is marked with a green circle and enclosed by
a orange border.
Names of input signals available for projection are displayed in white, and
unavailable signal names are grayed out. However, [Digital PC] and [Analog
PC-1] may be grayed out even when available.
2You can switch the available input signal types by pressing the INPUT
button.
You can select the target input signal with [ ] / [ ].
3Press the OK button to confirm the input signal type.
• Screens of computers connected to the projector over a network can be projected
when you have selected [LAN] as the input signal. For details, refer to the NMPJ user’s
manual.
• Images on USB flash drives can be projected when you have selected [USB] as the
input signal. For details, refer to “Projecting Images on a USB Flash Drive” (P157).
• In split-screen mode, the side without control rights is identified by a white circle.
Remote control Projector
Projection Procedure
57
Basic Guide Projection Procedure
Step 3 Adjust the Image
Setting the Display Resolution of the Computer
Based on the maximum resolution of the projector, set the display resolution of the
computer to the resolution closest to the output signal resolution of the projector.
(P188)
Maximum resolution
1920 X 1200 dots
■Windows 10
1Open the [Control Panel] from the start menu, then select [Appearance
and Personalization] - [Adjust screen resolution] in the [Control Panel
Home].
2Click the [Resolution] tab, and move the slider to select the resolution
closest to the maximum output signal resolution of the projector.
3Click the [OK] button.
■Windows 8 / 8.1
1Move the cursor toward the upper or lower right corner to access the
menu.
2Click [Settings], and then click [Control Panel].
3From [Control Panel Home] - [Appearance and Personalization], select
[Adjust screen resolution].
4Click the [Resolution] tab, and move the slider to select the resolution
closest to the maximum output signal resolution of the projector.
5Click the [OK] button.
■Windows 7
1Open the [Control Panel] from the start menu, then select [Appearance
and Personalization] - [Adjust screen resolution].
2Click the [Resolution] tab, and move the slider to select the resolution
closest to the maximum output signal resolution of the projector.
3Click the [OK] button.
58
Projection Procedure
■Windows Vista
1Open the [Control Panel] from the start menu, then select [Appearance
and Personalization] - [Adjust screen resolution] in the [Control Panel
Home].
2Select the resolution closest to the maximum output signal resolution of
the projector from the [Resolution] list.
3Click the [OK] button.
■Mac OS X
1Open the Apple Menu and select [System Preferences].
2In the [System Preferences] window, click the [Displays] icon to display
the Display window.
3Select the [Display] tab and select the resolution closest to the maximum
output signal resolution of the projector from the [Resolutions] list.
4Close the [System Preferences] window.
Auto PC Adjustment
If the image display is shifted or there is flickering of the screen when [Analog PC-1]
or [Analog PC-2] is selected, press the AUTO PC button to adjust the projector to
the optimal condition.
The adjustment results will be stored. If the projector is used again with the same
computer, when the input signal is selected the image will be projected
automatically under the same conditions that were previously adjusted.
If the Auto PC adjustment is insufficient, perform the following operations.
• Select the input signal that matches the resolution of the computer from [Input signal
select]. (P91)
• If adjustment is insufficient even when using the above operation, adjust [Total dots],
[Tracking], [Horizontal position], [Vertical position], [Horizontal pixels] and [Vertical
pixels] in [Input signal settings]. (P92)
• For the signal types supported by the projector, see the table on page 188 to 189.
Remote control
Projection Procedure
59
Basic Guide Projection Procedure
Focusing, Resizing, or Moving the Image
■Adjusting Image Focus
To adjust the focus, press the FOCUS button on the remote control or the LENS
button on the projector.
For the projection distances of the lens unit, refer to “Relationship Between Image
Size and Projecting Distance” on page 43.
1Press either the FOCUS button on the remote control or the LENS button
on the projector to display the focus adjustment window.
2Press the pointer buttons to adjust the focus.
3When the focus is adjusted optimally, press the OK button or the FOCUS
button.
Remote control Projector
Press once.
To adjust the focus, use the [ ] / [ ] / [ ] / [ ] buttons on the remote control or
projector.
To continue adjusting the focus in a specific direction, hold down the [ ] / [ ]
buttons on the remote control or projector.
Remote control Projector
60
Projection Procedure
■Adjusting Image Size
The size of the projected image can be adjusted by pressing the ZOOM button on
the remote control or the LENS button on the projector. Change the projector
installation position if your desired image is too large or too small to adjust it with
the zoom function. (P40)
1Press either the ZOOM button on the remote control or the LENS button
on the projector twice to display the zoom adjustment window.
2Press the pointer buttons to adjust the image size.
3When the desired image size is selected, press the OK button or the
ZOOM button.
When the Short Fixed Lens (RS-IL03WF) is attached, digital zoom adjustment is
performed in place of optical zoom adjustment.
Remote control Projector
Press twice.
To enlarge the image, use the [ ] / [ ] buttons on the remote control or
projector.
To reduce the image, use the [ ] / [ ] buttons on the remote control or
projector.
To continue adjusting the size in a specific direction, hold down the [ ] / [ ] /
[ ] / [ ] buttons on the remote control or projector.
Screen
Remote control Projector
Projection Procedure
61
Basic Guide Projection Procedure
■Adjusting the Image Position
To adjust the screen position up, down, left, or right, press the LENS-SHIFT button
on the remote control or the LENS button on the projector. It can change the
projected screen to the most suitable position by moving the position of the lens up/
down/left/right.
1Press either the LENS-SHIFT button on the remote control or the LENS
button on the projector three times to display the lens shift adjustment
window.
2Press the pointer buttons to adjust.
To raise or lower the image, use the [ ] / [ ] buttons on the remote control or
projector.
To move the image left or right, use the [ ] / [ ] buttons on the remote control
or projector.
To continue moving the image in a specific direction, hold down the
corresponding button.
3When the desired position is reached, press the OK button.
• The available range for lens shift (percentage of movement relative to the screen size)
varies depending on the lens unit which is used. (P47)
• Lens shift is not available in each corner for the Short Fixed Lens (RS-IL03WF) or in the
top left and top right for the other lenses. (P48)
Remote control Projector
Press three times.
Remote control Projector
Screen
62
Projection Procedure
■Resetting the Position
The lens position after movement with the
lens shift function is not returned when the
power is turned off. To return it to its original
position, perform reset.
During screen position adjustment, press and
hold the LENS-SHIFT button on the remote
control or the LENS button on the projector to display the [Lens shift reset] window.
The selections for the lens currently used are displayed. Use the pointer buttons to
select one of them, then press the OK button.
Lens unit type Available items
Standard Zoom Lens
RS-IL01ST
50% (Home position): Up 50%, left / right 0%
0%: Up / down / left / right 0%
Long Zoom Lens
RS-IL02LZ
Ultra Long Zoom Lens
RS-IL04UL
Wide Zoom Lens
RS-IL05WZ
Short Fixed Lens
RS-IL03WF 0% (Home position): Up / down / left / right 0%
Projection Procedure
63
Basic Guide Projection Procedure
Step 4 Select an Aspect Ratio (Screen Aspect)
Matching the Screen
Select an optimum aspect ratio of the projected image (screen aspect) or an
optimum screen mode (aspect) according to the aspect ratio of the screen, type of
input image signal and so on for the projection to make best use of the screen size.
You may need to change the setting depending on the resolution of the computer or
other AV equipment connected. If the image is not projected with the desired
aspect ratio, refer to “Relationship between Aspect and Screen Aspect” on page
183.
Selecting Screen Aspect
Select the correct aspect ratio for the screen which is used.
1Press the MENU button to display the menu window.
2Press the [ ] / [ ] buttons to select the [Install settings] tab.
[Screen aspect] Select the same screen aspect ratio as the screen you are
using.
[Aspect] In general, select [Auto].
When the Short Fixed Lens is attached and if the projected image does not fit on the
screen, you can display the image by electronically reducing its size.
The [Zoom] setting will appear in the menu only when the Short Fixed Lens (RS-IL03WF)
is attached.
Remote control Projector
Remote control Projector
64
Projection Procedure
3Select [Screen aspect] with the [ ] / [ ] buttons, and then press the OK
button.
4Use the [ ] / [ ] buttons to select the desired contents.
16:10
Select this when you use a screen with an aspect
ratio of 16:10. Also select this screen aspect when
projecting on a wall. You can correct keystone
distortion with this mode. (P67)
16:9
Select this when you use a screen with an aspect
ratio of 16:9. You can correct keystone distortion with
this mode. (P67)
4:3
Select this when you use a screen with an aspect
ratio of 4:3. You can correct keystone distortion with
this mode. (P67)
16:9 D. image shift
Select this when you use a screen with an aspect
ratio of 16:9. Keystone correction cannot be performed in this mode. However, it is
possible to move the image up / down when projecting level. For details about how
to move the image, refer to “Digital image shift” on page 107.
Remote control Projector
Remote control Projector
16:10 screen
16:9 screen
4:3 screen
Projection Procedure
65
Basic Guide Projection Procedure
4:3 D. image shift
Select this when you use a screen with an aspect ratio of 4:3. Keystone correction
cannot be performed in this mode. However, it is possible to move the image left /
right when projecting level. For details about how to move the image, refer to
“Digital image shift” on page 107.
5Press the OK button to accept your setting and then press the MENU
button.
Resetting the Image Shift
Perform the following steps to reset the image shift adjustment.
1Access the [D. image shift adjustment] window and press the D.SHIFT/
KEYSTONE button to display the [D. image shift reset] window.
2Next, select [OK] with the [ ] button, and then press the OK button.
Your specified [D.image shift adjustment] is now reset.
Select the Aspect
Select [Aspect] based on the input signal type, aspect ratio of the screen and
resolution. For more details about aspect ratios, refer to “Relationship between Aspect
and Screen Aspect” on page 183.
Types of Aspect Ratios
■Auto
An image is projected at the aspect ratio of the input signal. Select this mode for
normal image projection.
■16:10
The image is projected using an input signal aspect ratio of 16:10. Select this if an
image of 16:10 aspect ratio cannot be correctly projected in [Auto] mode.
■16:9
The image is projected using an input signal aspect ratio of 16:9. Select this if an
image of 16:9 aspect ratio cannot be correctly projected in [Auto] mode.
■4:3
The image is projected using an input signal aspect ratio of 4:3. Select this if an
image of 4:3 aspect ratio cannot be correctly projected in [Auto] mode.
There may be some cases when this cannot be selected, depending on the input signal
and/or resolution.
66
Projection Procedure
■Zoom
This cuts the upper / lower or left / right part of the screen according to the screen
aspect and zooms in the center of the image. Select this if a letter box is displayed
(black lines at the top/bottom of the screen) when watching video.
■True size
The image is projected with the original resolution of the input signal. Screens of
computers with a lower display resolution than the projector are displayed smaller
but clearer than in other aspect ratios.
Selecting an Aspect Ratio
Press the ASPECT button on the remote control and select an appropriate aspect
ratio. Press the ASPECT button to change the aspect ratio type. For more details
about aspect ratios, refer to “Relationship between Aspect and Screen Aspect” on
page 183.
You can also select any aspect ratio from [Aspect] in the menu. (P91)
There may be some cases when this cannot be selected, depending on the input signal
and/or resolution.
There may be some cases when this cannot be selected, depending on the input signal
and/or resolution.
Some aspect ratios may not appear depending on the type of input signal.
Example:
Remote control
Projection Procedure
67
Basic Guide Projection Procedure
Step 5 Adjusting Keystone Distortion
To correct keystone distortion, press the D.SHIFT/KEYSTONE button.
Two types of correction are available: horizontal/vertical correction and corner
correction.
Use horizontal/vertical keystone correction to adjust image width or height
distortion separately, and use corner correction to adjust the position of each corner
of the image.
For instructions on switching keystone correction, refer to “Keystone” (P106).
■Horizontal/Vertical Keystone Correction
1Press the D.SHIFT/KEYSTONE button on the remote control to display the
horizontal-vertical keystone adjustment window when [Keystone] is set
to [Horizontal-vertical keystone].
• The result of keystone adjustment is stored in memory. If you place the projector in the
same position, the keystone adjustment is not necessary.
• If keystone distortion is excessive and cannot be fully corrected, straighten the
projector so that it faces the screen directly.
• Signals are processed digitally when keystone distortion is corrected. The image may
look different from the original one. In addition, the aspect ratio of the image may
change.
• The digital image shift function is accessed when this button is pressed and the screen
aspect is [4:3 D. image shift] or [16:9 D. image shift]. (P107)
[Zoom] (P106) in the [Install settings] menu is not available during horizontal/vertical
keystone correction.
Remote control
68
Projection Procedure
2Press the pointer buttons to adjust the dimensions.
3When keystone distortion has been corrected, press the OK button.
■Corner Adjustment
1Press the D.SHIFT/KEYSTONE button on the remote control to display the
corner adjustment window when [Keystone] is set to [Corner
adjustment].
To correct top distortion,
press the [ ] button.
To correct bottom distortion,
press the [ ] button.
To correct distortion on the
right, press the [ ] button.
Screen
To correct distortion on the left,
press the [ ] button.
Remote control
Remote control
Projection Procedure
69
Basic Guide Projection Procedure
2Press the pointer button of the corner for correction, and then press the
OK button.
3Press the pointer buttons to adjust the corner.
4When you have finished correcting, press the OK button.
■Resetting the Keystone Adjustment
Horizontal-vertical keystone and corner adjustment can be reset as follows.
1First, press the D.SHIFT/KEYSTONE button on the remote control twice to
display the [Keystone reset] window.
2Next, select [OK] with the [ ] button, and then press the OK button.
Your specified keystone adjustment is now reset.
Corner adjustment settings will be cleared if you subsequently use [Zoom] (P106) in the
[Install settings] menu.
Remote control
Remote control
70
Projection Procedure
Step 6 Select the Image Quality (Image Mode)
You can select an image mode to suit the projected image.
In each image mode, you can further adjust the brightness, contrast, sharpness,
gamma, color adjustment, advanced adjustment, and lamp mode. (P97)
Image Modes
Available image modes vary depending on the selected input signal and whether
[HDMI image input] (P121) and [HDBaseT image input] (P121) is set to [Auto] or
[Computer].
: Compatible : Not compatible
*1 [HDMI image input] set to [Computer] *3 [HDMI image input] set to [Auto]
*2 [HDBaseT image input] set to [Computer] *4 [HDBaseT image input] set to [Auto]
Image
mode
Compatible input signals
• Digital PC
• Analog PC-1/2
• HDMI*1
• HDBaseT*2
•LAN
•USB
• Component
•HDMI*
3
• HDBaseT*4
Standard
(1) Bright
(2) Computer screens, or media played with
video software
(3) Whites and natural colors
Presentation
(1) Bright
(2) Images mainly consisting of text
(3) Keeps the screen bright
Dynamic
(1) Bright
(2) Media played with video software
(3) Keeps the screen bright
VividPhoto
(1) Somewhat dark
(2) Digital photos
(3) Produces vibrant colors
Video
(1) Somewhat dark
(2) Video from camcorders
(3) Close to the color space of TVs
Photo/sRGB
(1) Somewhat dark
(2) Digital photos from sRGB-compatible
cameras
(3) Conforms to the sRGB standard
Cinema
(1) Dark
(2) Movies
(3) Designed especially for movies
User 1 – 5
Up to 5 user-selected combinations of image
quality settings can be stored in the memory
(P97). Stored settings can be selected as an
image mode.
Functions
(1) Ambient Brightness
(2) Types of Images
(3) Image Mode Characteristics
Projection Procedure
71
Basic Guide Projection Procedure
■Selecting an Image Mode
Press the IMAGE button on the remote control to select.
The image mode changes each time the IMAGE button is pressed. (The displayed
image modes vary depending on the selected input signal.)
You can also select any image mode from the [Image mode] menu. (P97)
•User settings 1 - 5 are displayed when the desired image settings have been
created and stored using the user memory function in the image adjustment
menu. (P97)
Step 7 Turn the Projector Off
1Press the POWER button to display the window shown below.
2When this window is displayed, press the POWER button again to turn off
the power.
After you turn the power off, the projector will enter standby mode once it cools
down.
• If you want to continue projecting without turning off the power, press a button other
than POWER, or else wait until the confirmation message disappears.
• After turning off the projector, wait at least 5 minutes before turning it on again. It may
shorten the lamp life if you turn on the projector immediately after turning it off.
• Using the projector for extended periods may shorten the life of the lamp and internal
optical components.
• Unplug the projector if it will not be used for an extended period.
Remote control
Remote control Projector
72
Convenient Features
This section describes features convenient during presentations and in other
situations.
Temporarily Blacking Out an Image
Projection can be temporarily blanked after a presentation, or to divert the
audience’s attention away from the screen.
Press the BLANK button to black out the image.
Press the BLANK button again to show the image.
• You can set the screen state while blacking out the image in the menu.
(P117)
• The lamp remains illuminated while the image is blacked out.
Freezing the Picture
Projection can be temporarily frozen during computer operations that would be
distracting, or to pause playback of video or animation.
Press the FREEZE button to freeze the moving image. The
projector shows the following icon.
Press the FREEZE button again to return to the original display.
• It is also cancelled when the input signal is terminated.
Projecting Images Stored on a USB Flash Drive
Even without using a computer, you
can project images stored on a USB
flash drive simply by connecting it to
the USB port.
For instructions on projection from a
USB flash drive in the projector’s USB
port, see “Projecting Images on a USB
Flash Drive” (P157).
Remote control
Remote control
Screen
Convenient Features
73
Basic Guide Convenient Features
Projecting a Test Pattern from the Menu
Even without any input signals, the projector can project a test pattern. Test
patterns can be projected during installation to check how the projector is installed.
For details on projecting test patterns, see “Install settings” (P104) or “Displayed
Test Patterns” (P187).
Set Power-Saving Settings
Set power-saving settings as needed.
The following four settings are available. For details, refer to the page describing
each function.
• Lamp mode (P102)
Adjust lamp and fan power consumption in the image mode.
• Power management mode (P121)
Automatically turns off the lamp or the power after a certain period if the projector
is idle without an input signal.
• Power management duration (P122)
Specify the period after which the lamp or the projector should go off
automatically if left idle without an input signal when [Power management mode]
is set to [Lamp off] or [Standby].
• Network standby settings (P131)
Conserve energy in standby mode, as needed.
74
Convenient Features
Adjusting the Volume
Useful when:
• You want to adjust the volume level of the projector or external speakers.
Press the VOL button. The following screen appears.
• You can also adjust the volume level with the [ ] / [ ] buttons of the
projector.
• Adjust the volume or mute setting on the computer if the volume level is too
low.
• You can also adjust the volume level of the speakers connected via the
audio output terminal.
Muting the Sound
Useful when:
• You want to temporarily mute unnecessary sound.
• You want to immediately mute the sound.
Press the MUTE button to mute the sound. The projector shows
the following icon.
Press the
MUTE
button again to cancel the mute function.
• You can also mute the sound of the speakers connected via the audio output terminal.
Remote control
Remote control
Screen
Convenient Features
75
Basic Guide Convenient Features
Zooming Part of an Image
Useful when:
• Zooming in on an object such as a small graph during a presentation (up to 12x).
• Focusing on the current subject.
Press the +D.ZOOM button
to enlarge a part of the
image. Press the –D.ZOOM
button to reduce the image
size.
• The magnification appears on
the screen.
You can move the enlarged area by using the
[ ] / [ ] / [ ] / [ ] buttons.
You can restore the original size of the image by pressing the OK button.
The D.ZOOM buttons work differently than [Zoom] in the [Install settings] menu (P106).
Remote control
Screen
Screen
Remote control Projector
76
77
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced Guide
Using Menus
Menu Configuration
Menu Description
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
Advanced Guide
78
Using Menus
Use the menus to set the operation of the projector in detail.
Menu Configuration
The menu screen is divided into 6 tabs as shown below.
Contents of menu Menu items
[System settings] tab (
P116
)
You can set the operation of the projector.
[Image adjustment] tab (
P96
)
You can adjust the image quality and colors
according to your preference.
[Network settings] tab (
P129
)
These settings are for when using the projector
from a PC via a network.
[Information] tab (
P156
)
You can check information about the
signal types of the images projected and
other information.
[Install settings] tab (
P104
)
This setting is used when installing the projector.
[Input settings] tab (
P90
)
You can set the type of signal or the method of
projection of the images input.
79
Using Menus
Advanced Guide Using Menus
Basic Menu Operations
1Press the MENU button to display the menu window.
2Press the [ ] / [ ] buttons to select a tab.
•If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to
move the current selection to the top.
3Press the [ ] / [ ] buttons to select an item.
4Select contents.
How to select the contents varies depending on the item.
Selecting from a list Example: Aspect (P91)
Remote control Projector
Remote control Projector
Remote control Projector
1. Select [Aspect].
2. Press the OK button or [ ] button
to display a list of the contents.
3. Use the [ ] / [ ] buttons to select
the desired contents.
4. When you have found the
contents you desired, press the
OK button or [ ].
Using Menus
80
Adjusting with the [ ] / [ ] buttons Example: Contrast (P98)
Selecting from a different screen (1) Example: Menu position (P113)
Selecting from a different screen (2) Example: Tracking (P92)
5Pressing the MENU button causes the menu screen to disappear.
1. Select [Contrast].
2. Use the [ ] / [ ] buttons to adjust
the setting.
1. Select [Menu position].
2. Press the OK button to display a
different screen.
3. Then follow the instruction on the
screen.
1. Select [Input signal settings].
2. Press the OK button to display a
different screen.
3. Select [Tracking].
4. Use the [ ] / [ ] buttons to select
the setting, then use the [ ] / [ ]
buttons to select the value.
81
Advanced Guide Menu Configuration
Menu Configuration
Input settings (P90)
Aspect
Digital PC / Analog PC-1/2 / HDMI (when [HDMI In] is
[Computer]) / HDBaseT (when [HDBaseT In] is
[Computer])
P91
Auto*
16:10
16:9
4:3
True size
HDMI (when [HDMI In] is [Auto]) / Component /
HDBaseT (when [HDBaseT In] is [Auto])
Auto*
16:9
4:3
Zoom
True size
USB / LAN
Auto
Auto PC Analog PC-1 / 2 P91
Input signal select Analog PC-1 / 2 P91
640 x 480
:
1920 x 1200
Input signal settings Analog PC-1 / 2 P92
Total dots
Tracking
Horizontal position
Vertical position
Horizontal pixels
Vertical pixels
Input level HDMI / HDBaseT P93
Auto*
Normal
Expanded
Color space HDMI / HDBaseT P94
Auto*
RGB
YCbCr
Over scan*1 HDMI / HDBaseT P94
Off
On
Progressive Component / HDMI / HDBaseT P95
Off
Film/auto*
Video 1
Video 2
25p/30p(PsF)
* Factory default, or state after [Factory defaults] is executed.
*1 Factory default settings are based on these conditions: [On] when HDMI ([HDMI In]) is [Auto],
and [Off] when it is [Computer].
82
Menu Configuration
Image adjustment (P96)
Slideshow interval USB P95
[--:--]
:
[60:00]
Animation effect USB P95
Off*
Cross fade
Fade out/in
Split screen Digital PC / Analog PC-1/2 / HDMI / Component /
HDBaseT / LAN / USB
P93
Off*
On
Settings Split screen Off
On
Control rights Left screen
Right screen
Swap right-left Yes / No
Layout Mode 3-7
Mode 5-5
Mode 7-3
Image priority (in split-screen mode) COMMON P96
Primary*
Secondary
Image mode COMMON P97
Standard*
Photo/sRGB
User 1 - 5 (when creating profile)
Digital PC / Analog PC-1/2 / HDMI (when [HDMI In] is
[Computer]) / HDBaseT (when [HDBaseT In] is
[Computer]) / LAN / USB
VividPhoto
Presentation*
Component / HDMI (when [HDMI In] is [Auto]) /
HDBaseT (when [HDBaseT In] is [Auto])
Dynamic
Video
Cinema
Create profile P97
Save profile
(Displayed when image mode 1 - 5 is
selected)
P97
Baseline image mode
(Displayed when image mode 1 - 5 is
selected)
P97
Brightness P98
* Factory default, or state after [Factory defaults] is executed.
Menu Configuration
83
Advanced Guide Menu Configuration
Contrast P98
Sharpness P98
Gamma P98
Color adjustment Color level P98
Color balance
Color temperature
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Advanced adjustment P99
Ambient light Off* P99
Adjust
Type Tungsten
Fluorescent*
Level L
H*
Random noise reduction Off* P99
Weak
Middle
Strong
MPEG noise reduction Off* P100
Weak
Middle
Strong
Mosquito noise reduction Off* P100
Weak
Middle
Strong
Dynamic gamma*2 Off P100
Weak
Middle
Strong
Mem. color correct*3 Flesh Off P100
Sky Weak
Green Middle
Strong
* Factory default, or state after [Factory defaults] is executed.
Under the following setting, differs from factory defaults.
*2 • For Analog PC-1/2, Digital PC or HDMI (when [HDMI In] is [Computer]), the factory default is
[Off].
• [Weak] by default for Component or HDMI (when [HDMI In] is [Auto]).
*3 • [Off] by default for HDMI (when [HDMI In] is [Computer]), or for Digital PC, Analog PC (1 or
2), USB, or LAN.
• HDMI (when [HDMI In] is [Auto]) or COMPONENT: Weak
84
Menu Configuration
Install settings (P104)
6-axis color adjust Off* P101
Adjust
Hue
Saturation
Brightness
Reset
Fine-Tune Gamma P101
Lamp control Off* P102
On
Lamp mode Full power* P102
Power saver
Reset P103
Positional lock Off* P105
On
Image flip H/V None* P105
Ceiling mounted
Rear
Rear, Ceiling mounted
Screen aspect 16:10* P105
16:9
4:3
16:9 D. image shift
4:3 D. image shift
Zoom P106
Keystone Horizontal-vertical keystone* P106
Corner adjustment
Reset
Digital image shift P107
Professional settings
Micro-digital image shift Off* P107
Adjust
Registration Off* P107
Adjust
Fan mode Normal* P108
High altitude
Vertical projection Off* P108
Upward
Downward
* Factory default, or state after [Factory defaults] is executed.
Menu Configuration
85
Advanced Guide Menu Configuration
Edge blending Off* P109
Adjust
Side
Color blending adjustment
Black level adjustment
Marker
Reset
Lens - Position Load position 1-3 P112
Save position 1-3
Lens shift reset
Screen color Normal* P113
Greenboard
Adjust
Red / Green / Blue
On screen P113
Menu position Upper L P113
Upper R
Center*
Lower L
Lower R
Guide Off P113
On*
Show input status Off P114
On*
Overheat warning display Off* P114
On
Menu display time Normal* P114
Extended
Lamp warning display Off P115
On*
Air filter warning display Off P115
On*
Split screen ID display Off P115
On*
Test pattern Off* P115
On
* Factory default, or state after [Factory defaults] is executed.
86
Menu Configuration
System settings (P116)
User screen settings P117
Logo capture P117
Logo position Upper L P117
Upper R
Center
Lower L
Lower R
No signal screen Black P117
Blue*
User logo
Screen when blank Black* P117
Blue
User logo
Projector on Skip P118
Canon logo*
User logo
Interface settings P118
Key repeat Off P118
On*
Key lock Off* P118
Main unit
Remote (wireless)
Remote control channel Ch1 - 4 P119
Independent*
Audio in terminal select P119
HDMI Off
Audio in 1
Audio in 2
HDMI*
Digital PC Off
Audio in 1*
Audio in 2
Analog PC-1 Off
Audio in 1*
Audio in 2
Analog PC-2 Off
Audio in 1
Audio in 2*
Component Off
Audio in 1
Audio in 2*
* Factory default, or state after [Factory defaults] is executed.
Menu Configuration
87
Advanced Guide Menu Configuration
HDBaseT Off
Audio in 1
Audio in 2
HDBaseT*
LAN Off
Audio in 1
Audio in 2
LAN*
USB Off
Audio in 1*
Audio in 2
HDBaseT Off* P120
On
Image signal quality
Communication settings Serial communication P120
Service port*
HDBaseT
Detail
Baud rate
Data bits
Parity
Stop bit
1*
2
Wired network
LAN port*
HDBaseT
HDMI image input Auto
Computer*
HDBaseT image input Auto
Computer*
Power management mode Disabled P121
Lamp off
Standby*
Power management duration 5 min. P122
10 min.
15 min.*
20 min.
30 min.
60 min.
Direct power on Off* P122
On
Beep Off
P122
On*
Motion blur reduction Off* P123
On
* Factory default, or state after [Factory defaults] is executed.
88
Menu Configuration
Network settings (P127)
Language English Turkish P123
German Polish
French Hungarian
Italian Czech
Spanish Danish
Portuguese Arabic
Swedish Chinese (Simplified)
Russian Chinese (Traditional)
Dutch Korean
Finnish Japanese
Norwegian
Other settings P124
Password settings Off* P124
On
Register password Password input P125
[Fn] button settings Disable* P125
Split screen
Gamma restore Off* P125
Adjust
Lamp counter Reset / Return P125
Air filter counter Reset / Return P126
Power counter P126
Firmware Yes / No P126
Factory defaults OK / Cancel P126
Network settings lock Unlock P130
Lock*
Network password setting Off P130
On*
Register network password P130
Network standby settings Normal P131
Low-power*
Network function Off* P131
On
Detailed settings P132
IP address
Gateway address
* Factory default, or state after [Factory defaults] is executed.
Menu Configuration
89
Advanced Guide Menu Configuration
Information (P156)
MAC address
DHCP Off*
On
TCP/IP settings IP address
Subnet mask
Gateway address
Apply
Network setting initialization Yes / No
PJLink Off P134
On*
AMX Device Discovery Off* P135
On
Crestron RoomView Off* P135
On
Model name
Input signal
Firmware
Serial no.
Projector usage time
IP address
E-mail sender address
E-mail recipient address
Projector name
Comments
System information ID
The following settings are not reset even when factory defaults are restored.
• Selected input signal
• Lamp counter
• Language
• Remote control channel
• Network settings
• Air filter counter
• Micro-digital image shift
• Registration
• Fan mode
• Vertical projection
• HDBaseT
• Wired network
• Serial communication
• User profile
• Lens - Position
• Projector usage time
• Power counter
* Factory default, or state after [Factory defaults] is executed.
90
Menu Description
Input settings
This section describes settings for aspect ratio, resolution, and projection
from a USB flash drive.
(When the input signal is Analog PC-1)
Menus that are not available are grayed out or hidden.
Menu Function Details
Aspect Select an image aspect ratio. P91
Auto PC Automatically adjusts display position misalignment
and screen flickering. P91
Input signal select Manually set a resolution to suit computer images. P91
Input signal settings Complete input signal settings. P92
Split screen Project two input images side by side. P93
Input level Select the input level for HDMI or HDBaseT signals. P93
Color space Select the color space for HDMI or HDBaseT signals. P94
Over scan Trim peripheral distortion from HDMI or HDBaseT
images before projection. P94
Progressive Select progressive processing for still images in
cinematic content or moving images in videos. P95
Slideshow interval Specify how long individual images on a USB flash
drive are projected in slideshows. P95
Animation effect Specify the transition between images on a USB flash
drive in slideshows. P95
91
Menu Description
Advanced Guide Menu Description
Aspect
> [Input settings] > [Aspect]
Select a projection aspect ratio for images.
Menus that are not available are grayed out or hidden.
Auto PC
> [Input settings] > [Auto PC]
Automatically adjusts display position misalignment and screen flickering.
Input signal select
> [Input settings] > [Input signal select]
Select a suitable resolution if Auto PC (P58) does not project computer images
correctly.
Select the input signal that matches the computer resolution. Press the OK button
to confirm the setting, and then press the MENU button.
Option Function
Auto An image is projected at the aspect ratio of the input signal.
Suitable for most projection.
16:10 The image is projected using an input signal aspect ratio of 16:10.
16:9 The image is projected using an input signal aspect ratio of 16:9.
4:3 The image is projected using an input signal aspect ratio of 4:3.
Zoom
This cuts the upper/lower or left/right part of the screen according
to the screen aspect and zooms in or out of the center of the
image.
True size The image is projected with the original resolution of the input
signal.
• For LAN and USB input, [Auto] is selected automatically.
• Different contents are displayed for different screen aspects or input signal types.
•The ASPECT button on the remote control can also be used to select the [Aspect]
settings.
If the Auto PC adjustment is insufficient, perform the following operations.
• Select the input signal that matches the computer resolution from [Input signal select].
• If adjustment remains insufficient, adjust [Total dots], [Tracking], [Horizontal/Vertical
position] and [Horizontal/Vertical pixels] in [Input signal settings]. (P92)
• For supported signals, see the table on page 188 – 189.
For supported signals, see the table on page 188 – 189.
Menu Description
92
Input signal settings
> [Input settings] > [Input signal settings]
Complete input signal settings. Use the [ ] / [ ] buttons to adjust the levels as
needed.
Submenu Function
Tota l do ts Adjust the total number of horizontal dots. Adjust it when stripes
are displayed on the screen.
Tracking Fine-tune the timing of image generation from signals. Adjusts the
tracking when the image distorts or flickers.
Horizontal position Adjust the horizontal image position to correct horizontal
misalignment.
Vertical position Adjust the vertical image position to correct vertical misalignment.
Horizontal pixels Adjust the horizontal image resolution.
Vertical pixels Adjust the vertical image resolution.
Perform this adjustment if the Auto PC function (P91) cannot adjust the projected image
correctly.
Total dots
Horizontal pixels
Horizontal
position
Vertical position
Vertical
pixels
Total lines
93
Menu Description
Advanced Guide Menu Description
Split screen
> [Input settings] > [Split screen]
Two input images from devices connected to the projector can be projected side by
side.
For details on split-screen mode, see “Split-Screen Display” (P161).
Input level
> [Input settings] > [Input level]
Adjust the input level for content projected via HDMI or HDBaseT.
Option Function
Off Exit split-screen mode.
On Activate split-screen mode.
Settings
• Network and USB input cannot be combined for split-screen display. Similarly,
HDBaseT and HDMI input cannot be combined.
• Control can be switched to the other side by pressing the [ ] / [ ] on the remote
control when ( ) or ( ) is displayed in the center of the image area.
• When you switch to split-screen display, the left and right signals and input status are
shown in the input window.
Option Function
Auto Automatically switches the input level based on the input signal.
Normal Limits the input level to 16 - 235.
Expanded Enables a full input level of 0 - 255.
Submenu Function
Split screen Switch between normal and split-screen projection.
Control rights
Select the image to control. When the left image is
selected, 1 is displayed, and when the right image is
selected, 2 is displayed.
Swap right-
left Switch the sides that images are projected on.
Layout
Mode 3-7 Use 30% of the screen width for the left
side and 70% for the right.
Mode 5-5 Use 50% of the screen width for the left
side and 50% for the right.
Mode 7-3 Use 70% of the screen width for the left
side and 30% for the right.
Menu Description
94
Color space
> [Input settings] > [Color space]
Select the color space for HDMI or HDBaseT signals.
Over scan
> [Input settings] > [Over scan]
Select this setting to trim peripheral distortion from content projected via HDMI or
HDBaseT.
• You can select this only when the type of signal sent from AV equipment is RGB.
• In [Auto] mode, the signal level is selected automatically. (Some AV equipment and
HDBaseT transmitters may not support this.)
• If your AV equipment HDMI output can be set to [Normal] or [Expanded], we
recommend [Expanded]. The contrast of images will be improved and dark scenes will
be rendered more realistically. In this case, set [Input Level] to [Auto] or [Expanded].
For more detailed information, refer to the user’s manual for the AV equipment
connected to the projector.
Option Function
Auto Selects the optimal color format for input signals.
RGB Forces the projector to handle the input signal as an RGB signal.
YCbCr Forces the projector to handle the input signal as a color difference
signal.
Option Function
Off Project all (100%) of the input signal.
The images projected may be smaller than the full projection screen.
On Project images with peripheral distortion removed. (5% of the image is
trimmed, along the edges.)
With some signal resolutions, image edges may be cut off. In such a case, select [Off].
95
Menu Description
Advanced Guide Menu Description
Progressive
> [Input settings] > [Progressive]
Performs progressive processing optimized for still images in cinematic content or
moving images in videos.
Slideshow interval
> [Input settings] > [Slideshow interval]
You can project images on a USB flash drive automatically, one after another.
Use the [ ] / [ ] buttons to set the interval after which images are switched in a
range of 1 seconds to 60 minutes, in the format min.:sec.
Animation effect
> [Input settings] > [Animation effect]
Specify the transition for slideshows of images on a USB flash drive.
Option Function
Off Does not perform progressive processing.
Film/auto Suitable for still images or typical moving images. Performs progressive
processing for video or cinematic content.
Video 1 Suitable for projecting video with high image quality and relatively slow
movement. Performs progressive processing optimized for HD video.
Video 2 Suitable for projecting video with faster movement. Performs
progressive processing optimized for fast-moving video.
25p/30p (PsF) Performs progressive processing optimized for 1080 PsF/25 or
1080 PsF/30 video (25 or 30 fps, respectively).
• Select [Off] when flickers and horizontal lines are noticeable in media that has a lot of
fast-moving action.
• Not available in split-screen mode.
• Switching the input signal to an option other than [USB] will stop any slideshow in
progress. To resume the slideshow from the last image shown, return the input signal to
[USB].
• If you use digital zoom during a slideshow, the digital zoom will be cancelled when you
switch to the next image.
Option Function
Off Disable slideshow transitions.
Cross fade Fade out one image as the next image fades in.
Fade out/in Fade out one image to black, and then fade the next image in.
Menu Description
96
Image adjustment
This section describes image quality settings such as brightness, contrast,
and sharpness.
(When the input signal is Analog PC-1)
Menus that are not available are grayed out or hidden.
* Any adjustments you make are stored for each combination of input signal and
image mode.
Menu Function Details
Image mode * Select overall image quality to suit the projected image. P97
Create profile Save desired image quality settings as profiles. P97
Baseline image mode Shows the image mode that is basis of the profile. P97
Brightness * Adjust image brightness. P98
Contrast * Adjust image contrast. P98
Sharpness * Adjust image sharpness. P98
Gamma * Correct loss of detail in shadows or highlights. P98
Color adjustment * Fine-tune image colors. P98
Advanced adjustment * Fine-tune noise reduction and color tone. P99
Lamp mode * Select the lamp brightness. P102
Reset Restore default image settings. P103
Image priority * Select which side is the basis for image processing in
split-screen mode. P103
97
Menu Description
Advanced Guide Menu Description
Image mode
> [Image adjustment] > [Image mode]
Select the overall image quality for projected images. Can also be selected by
pressing the IMAGE button on the remote control. (P70)
Menus that are not available are grayed out or hidden.
Create profile
> [Image adjustment] > [Create profile]
Save desired image quality settings in up to five user profiles.
Option Types of Images Characteristics
Standard Computer screens, or media
played with video software
Bright overall; white, with natural
colors
Presentation Images mainly consisting of text Bright overall
Dynamic Video content Bright overall
VividPhoto Digital photos Subdued brightness overall, with
vibrant colors
Video Video from camcorders Somewhat dark; colors resemble
TV
Photo/sRGB Digital photos from sRGB-
compatible cameras
Somewhat dark; conforms to the
sRGB standard
Cinema Movies Designed especially for movies
User 1 - 5
Up to five user profiles can be stored for your selected image quality
settings. Stored profiles are available in this setting as an image
mode.
You can adjust the image quality by adjusting the following items in each image mode:
[Brightness], [Contrast], [Sharpness], [Gamma], [Color adjustment], [Advanced
adjustment], and [Lamp mode]
• The saved settings consist of the brightness, contrast, sharpness, gamma, color
adjustment, advanced adjustment, and lamp mode.
• Although only five user profiles are displayed, different profiles can be created to apply
depending on whether the projector is connected to a computer (with Analog PC,
Digital PC, HDMI (when [HDMI image input] (P121) is [Computer]), or HDBaseT (when
[HDBaseT image input] (P121) is [Computer])), AV equipment (with Component, HDMI
(when [HDMI image input] (P121) is [Auto]), or HDBaseT (when [HDBaseT image
input] (P121) is [Auto])), a LAN, or a USB flash drive. As a result, it is possible to save
up to 10 settings.
• The image mode name which was the basis for the settings change is also saved in the
user memory. When a user memory is selected as the image mode, the image mode
that was the base for that user memory is displayed in the menu as [Baseline image
mode].
Menu Description
98
Brightness
> [Image adjustment] > [Brightness]
Adjust image brightness.
Contrast
> [Image adjustment] > [Contrast]
Sharpen or soften image contrast.
Sharpness
> [Image adjustment] > [Sharpness]
Adjust image sharpness.
Gamma
> [Image adjustment] > [Gamma]
Correct image areas that are too dark or too bright to see clearly. Can also be
selected by pressing the GAMMA button on the remote control.
Color adjustment
> [Image adjustment] > [Color adjustment]
Adjust color-related settings such as color level, color balance, and color
temperature.
For more detailed adjustment, use Fine-Tune Gamma (P101).
Submenu Function
Color level Adjusts the intensity of colors.
Color balance Adjusts the color balance of a purplish or greenish image.
Color temperature Adjusts the white color temperature.
R / G / B Gain Adjust the gain of each color.
R / G / B Offset Adjusts the color offset of each color.
99
Menu Description
Advanced Guide Menu Description
Advanced adjustment
> [Image adjustment] > [Advanced adjustment]
Fine-tune noise reduction and color tone.
Ambient light
Minimize the effect of ambient light on the screen.
Option Function
Off Projects an image with no correction.
Adjust
Type
Tungsten For ambient light from conventional light bulbs
or fluorescent light of this color.
Fluorescent For ambient light from a “day white” fluorescent
source.
Level LFor an ordinary brightness of ambient light.
HFor bright ambient light.
Random noise reduction
Reduce random image noise*.
* Effective on noise with an irregular frequency or amplitude.
Option Function
Off Disables random noise reduction.
Weak
Middle
Strong
Specify one of three levels of intensity of the random noise reduction.
Examples of Ambient Light Level Settings
Level Example Location
LProjection room, sports bar, etc.
HConference room, lecture room, etc.
The [Ambient light] setting is available in Photo/sRGB, Video, and Cinema image
modes. (P97)
• Select [Weak] for fast-moving images or [Strong] for slow-moving images.
• This setting is not displayed for LAN or USB input.
Menu Description
100
MPEG noise reduction
Reduce MPEG image noise*.
* Block noise resembles pixelation and may affect either on JPEG images or in MPEG
video.
Option Function
Off Disables MPEG noise reduction.
Weak
Middle
Strong
Specify one of three levels of intensity of the MPEG noise reduction.
Mosquito noise reduction
Reduce mosquito noise*.
* A type of noise affecting image edges or areas where colors change significantly, either on
JPEG images or in MPEG video.
Option Function
Off Disables mosquito noise reduction.
Weak
Middle
Strong
Specify one of three levels of intensity of the mosquito noise reduction.
Dynamic gamma
You can adjust the gradation representation of light and dark portions of an image
automatically.
Option Function
Off Disable dynamic gamma adjustment.
Weak
Middle
Strong
Specify one of three levels of dynamic gamma adjustment.
Mem. color correct
Enhances skin tones, blue skies, and greens, so that these colors are more consistent with
people’s remembered impressions.
Submenu Function
Flesh
Sky
Green
Off Disable correction.
Weak
Middle
Strong
Specify the level of correction.
This setting is not displayed for LAN or USB input.
This setting is not displayed for HDMI, Digital PC, Analog PC-1, Analog PC-2, or
Component input signals.
101
Menu Description
Advanced Guide Menu Description
6-axis color adjust
Fine-tune RGB (red, green, blue) and CMY (cyan, magenta, yellow) hues in images.
Option Function
Off Disables 6-axis color adjustment.
Adjust
Use the [ ] / [ ] buttons to select [ Hue], [ Saturation], or
[ Brightness], and use the [ ] / [ ] buttons for adjustment.
•When you are finished adjusting the color, press the OK button.
Reset Returns all adjustment values to zero.
Fine-Tune Gamma
Adjust white, red, green, and blue gamma curves. Red, green, and blue can be adjusted
separately. Adjustments to white are also applied to the three other colors. Note that adjusting
any color will overwrite previous adjustments.
Adjustment is not applied to the projected menu itself.
• For details on gamma correction, see page 98.
• Use input signals or a test pattern for adjustment.
• Adjustment is not applied to the projected menu itself.
• Use the [ ] / [ ] buttons to select a color, and then press the OK button.
Next use the [ ] / [ ] buttons to select a point on the gamma curve, and then use
the [ ] / [ ] buttons to adjust the position of the point. When adjustment is finished,
press the OK button to confirm the setting.
Menu Description
102
Lamp mode
> [Image adjustment] > [Lamp mode]
Reducing the lamp brightness reduces power consumption and cooling fan noise.
Lamp control
Dims the lamp automatically when the input signal is completely black.
Option Function
Off No lamp control.
On Lamp control. Dims the lamp in response to fully black input signals. Normal
brightness is restored once the input signal changes from fully black.
•The projector automatically enters standby mode if the lamp is dimmed (that is,
if the input signal is fully black) for more than one hour. A countdown window is
displayed 10 minutes before entering standby.
•The lamp is not dimmed when projection is blanked, when no signals are
supplied, or when black is projected during gamma restore.
•Lamp control is not available for the following settings:
-In split-screen mode
-During test pattern projection
-When [Lamp mode] is set to [Power saver]
-When [Vertical projection] is set to [Upward] or [Downward]
-When [Fan mode] is set to [High altitude]
•No lamp control is performed in the first 20 minutes after the projector is turned
on.
• All image adjustments are stored as modified settings for the current input signal and
image mode.
• Resolution may seem lower with [Random noise reduction], [MPEG noise reduction], or
[Mosquito noise reduction].
Option Function
Full power Projects images at full brightness.
Power saver Reduces lamp brightness to save energy.
• This setting can also be adjusted from the power saver settings screen by pressing the
LAMP button on the remote control.
• The lamp mode is set to [Power saver] and cannot be changed when [Install settings] >
[Fan mode] is set to [High altitude].
103
Menu Description
Advanced Guide Menu Description
Reset
> [Image adjustment] > [Reset]
Restore the current image quality settings to the factory defaults.
Image priority
> [Image adjustment] > [Image priority]
Select which side image adjustment settings to apply in split-screen mode.
Option Function
OK Resets the image adjustment settings.
Cancel Cancels resetting of the image adjustment settings.
• Performing reset when [Image mode] is set to a profile from [User 1] to [User 5] will
restore the settings originally saved for that user profile.
• Only the setting for the combination of input signal and image mode for the current
projection is reset.
Option Function
Primary
Use the side with control rights as the [Primary] side. For image
adjustment settings that are not configured separately, [Primary] side
settings apply to both sides.
Secondary
Not available when the [Primary] side has control rights. To reverse the
side given priority for image adjustment (whether on the left or right
side), switch control rights to the other side and change [Secondary] to
[Primary].
•Can be independently configured
Brightness (P98), Contrast (P98), Gamma (P98), Color adjustment (P98), Fine-Tune
Gamma (P101)
• [Primary] setting also applies to [Secondary]
Image mode (P97), Advanced adjustment except Fine-Tune Gamma (P99 - P101), Lamp
mode (P102)
Menu Description
104
Install settings
Adjust projection to suit the screen or the type of images, or how the
projector is installed.
(When the input signal is Analog PC-1)
Menu Function Details
Positional lock Operation of installation related functions can be
prohibited. P105
Image flip H/V Specify settings for projection from behind the screen,
from the ceiling, or both. P105
Screen aspect Select an aspect ratio that matches that of the
projection screen. (P63)P105
Zoom Digitally reduce images projected with a Short Fixed
Lens. P106
Keystone Set the type of keystone correction. P106
Digital image shift Moves the position of the projected image. P107
Professional settings Specify settings for image positioning and the altitude
of installation. P107
Lens - Position Save the current lens information, or restore previous
lens conditions that were saved. P112
Screen color Adjust projection colors to suit the screen color. P113
On screen Specify display details for on-screen menus, help, and
warning or precaution icons. P113
Test pattern Project a test pattern to check the resolution and color
of projection during installation. P115
105
Menu Description
Advanced Guide Menu Description
Positional lock
> [Install settings] > [Positional lock]
Operation of installation-related functions can be prohibited.
•Image flip H/V • Screen aspect • Keystone
•Save position (in [Lens - Position]) • Lens shift reset
•Digital image shift • Professional settings
Press the OK button to confirm the setting, and then press the MENU button.
Image flip H/V
> [Install settings] > [Image flip H/V]
Specify the orientation of how the projector is installed.
Screen aspect
> [Install settings] > [Screen aspect]
Select an aspect ratio that matches that of the projection screen.
Option Function
Off The positional lock is not used.
On Prevents adjustment of installation-related functions.
Option Function
None Select for normal projection, without inversion.
Ceiling mounted
Select when the projector is installed upside-down on the ceiling.
The projected image is inverted in both vertical and horizontal
directions.
Rear Select this to project an image from behind the screen.
The projected image is inverted in the horizontal direction.
Rear, Ceiling mounted
Select this to project an image from behind the screen with the
projector hung from the ceiling.
The projected image is inverted in the vertical direction.
• To hang the projector from the ceiling, use the optional bracket. Contact the Canon
Customer Support Center for more detailed information.
• Image flipping will reset any adjustment for keystone distortion. In this case, redo the
adjustment.
Option Function
16:10 Select this when you use a screen with an aspect ratio of 16:10.
16:9 Select this when you use a screen with an aspect ratio of 16:9.
4:3 Select this when you use a screen with an aspect ratio of 4:3.
16:9 D. Image Shift
Select this when you use a screen with an aspect ratio of 16:9.
Although keystone correction is not available in this mode, images
can be shifted up or down. (P64)
4:3 D. Image Shift
Select this when you use a screen with an aspect ratio of 4:3.
Although keystone correction is not available in this mode, images
can be shifted left or right. (P65)
Menu Description
106
Zoom
> [Install settings] > [Zoom]
When the Short Fixed Lens is attached and if the projected image does not fit on
the screen, you can display the image by electronically reducing its size. This type
of zooming reduces overall image dimensions, relative to the center of the image.
Press the [ ] button on the remote control to project images at a reduced size, and
press the [ ] button to enlarge images to full size. Images can be projected at 75-
100% of the original size.
Keystone
> [Install settings] > [Keystone]
Two types of keystone correction are available: horizontal/vertical keystone and
corner adjustment. Keystone correction can also be reset. Keystone correction can
also be applied by pressing the KEYSTONE button on the remote control.
• Changing the screen aspect will reset any keystone or digital image shift setting.
• [Auto] may be automatically selected for the aspect depending on the screen aspect
setting.
• D.ZOOM buttons on the remote control cannot be used for this [Zoom] function.
• [Zoom] is not available when the following features are used.
-Horizontal/vertical keystone correction
-Split-screen mode (P161)
• Using [Zoom] after specifying corner adjustment (P166) will clear corner adjustment
settings and apply the zoom setting. Instead, use [Zoom] before fine-tuning the image
position with corner adjustment.
• If images still extend off the screen even after you use [Zoom], you can use corner
adjustment (P166) to finetune the position of image corners, so that images fit on the
screen.
• Switching to lenses other than the Short Fixed Lens will reset the setting to 100%.
Submenu Function
Horizontal-vertical
keystone
Apply horizontal-vertical keystone correction. Image height and
length is adjusted.
Corner adjustment Apply corner adjustment. Each corner of the image can be
repositioned.
Reset Resets the specified keystone value.
• Pressing the KEYSTONE button when the screen aspect is 16:9 D. image shift or 4:3
D. image shift will apply digital image shift.
• Resetting the keystone value will also reset the zoom setting for the Short Fixed Lens
(RS-IL03WF).
107
Menu Description
Advanced Guide Menu Description
Digital image shift
> [Install settings] > [Digital image shift]
Moves the position of the projected image.
When screen aspect is 16:9 D. Image Shift, move images vertically using the [ ] /
[ ] buttons, and for 4:3 D. Image Shift, move images horizontally using the [ ] / [ ]
buttons.
Professional settings
> [Install settings] > [Professional settings]
Specify advanced installation settings.
This cannot be selected when the screen aspect is 16:9, 16:10 or 4:3.
Micro-digital image shift
Use this setting to fine-tune the position of the projected image.
Submenu Function
Off Does not perform micro digital image shift.
Adjust
Adjust Use the [ ] / [ ] buttons for vertical shift and the [ ] /
[ ] buttons for horizontal shift.
Chart Displays a chart to assist in adjustment. Watch the chart
as you fine-tune the position.
Return Dismiss the chart.
Registration
Adjusts colors that are out of alignment. You can adjust red, green and blue registration
independently.
Submenu Function
Off Does not perform image registration.
Adjust
Red / Green /
Blue
Use the [ ] / [ ] buttons for vertical shift and the [ ] /
[ ] buttons for horizontal shift.
Chart Displays a chart to assist in adjustment. Watch the chart
as you fine-tune the position.
Return Dismiss the chart.
Menu Description
108
Fan mode
Switch the fan mode to suit installation at low or high altitudes (above 2,300 m (7,545.8')).
Option Function
Normal Setting for altitudes lower than 2,300 m (7,545.8').
High altitude Setting for altitudes of 2,300 m (7,545.8') or higher.
Vertical projection
You can ensure adequate cooling by switching the fan mode to suit upward- or downward-
facing installations. For precautions on vertical projection, see “Install Facing in the Correct
Direction” (P25).
Option Function
Off Does not alter the fan mode.
Upward Setting for use when the projector faces upward.
Downward Setting for downward projection.
• Incorrect settings may shorten the useful life of the lamp or other parts.
• The lamp mode is set to [Power saver] and cannot be changed when [Install
settings] > [Fan mode] is set to [High altitude].
• Be sure to perform this setting to use vertical projection.
• Projecting vertically without using this setting will shorten the useful life of the lamp
and other parts.
• Even if you complete this setting, vertical projection will result in a shorter useful life
of the lamp and other parts than horizontal projection.
109
Menu Description
Advanced Guide Menu Description
Edge blending
Brightness and colors of overlapping edges of images from multiple projectors, which form a
blending area, can be adjusted for a more seamless appearance. For detailed instructions, see
“Projecting from Multiple Projectors at Once (Edge Blending)” (P162).
[Off] Disable blending.
[Adjust] Display the menu for blending area adjustment.
Start marker End marker
Blending area
When adjusting the image
projected from the right side
• Adjustment may not eliminate different colors or brightnesses in the blending area.
• For best edge-blending results, use all projectors in the same image mode and make
the following adjustments.
(1) Brightness, contrast, R/G/B gain and offset, black level, blending color, color
temperature, color level, color balance, sharpness, and gamma (P98)
(2) Color adjustment, by using 6-axis color adjustment (P101)
(3) Gamma adjustment, by using fine-tune gamma (P101)
(4) Corner adjustment, using keystone correction (P106)
Menu Description
110
Submenu Function
Side
Left, Right,
Top, Bottom Select the direction of the blending area to adjust.
Width Specify the width between the start and end markers.
Start
position Moves the position of the start marker.
Color blending
adjustment
Adjust unwanted colors or discrepancies between colors in the blending
area.
Submenu Function
Off Do not adjust colors of blended images.
Adjust
Adjust unwanted colors or discrepancies between colors
in the blending area.
• Large blending areas may cover input signal dialog boxes and
other interface elements. In this case, momentarily set edge
blending to [Off] and check the display.
• Although the starting marker is normally aligned with the image
edge, it can also be aligned toward the center of the image. In
this case, the black blending area will lie outside of the starting
marker.
Option Function
White
Simultaneously adjust red, green,
and blue to correct unwanted
colors or discrepancies in the
blending area.
Red/Green/Blue
Individually adjust red, green, and
blue to correct unwanted colors or
discrepancies in the blending
area.
111
Menu Description
Advanced Guide Menu Description
Submenu Function
Black level
adjustment
Because black is lighter in the blending area than in other areas, you can
adjust the black level outside the blending area to make this difference in
brightness less noticeable.
Off
Do not adjust the black level.
Area
Adjust areas C - A to smoothen the boundaries of the blending area.
Black level
Adjust the black level brightness and color of areas B and D.
Marker
Show the blending area markers.
Option Function
Off Hide the blending area markers.
On Show the blending area markers. The start marker is red,
and the end marker is green.
Reset Reset the marker settings.
CBA
Left image
Position of end
marker (hidden)
Area D Blending area
Areas C - A (default: 0)
Area A: Black level cannot be adjusted.
Area B: Adjust to a black level different
from that of area D.
Area C: Adjust to provide a smooth
transition relative to the black
levels of areas B and D.
Option Function
Side Select the direction to adjust from Left/Right/
Top/Bottom.
A-Width/ B-Width/
C-Width Adjust the widths of areas A - C.
Option Function
B/D-area base Adjust the black level brightness of B/D areas.
B/D-area red / green /
blue
Adjust the red, green, and blue components of
B/D area black levels individually.
Menu Description
112
Lens - Position
> [Install settings] > [Lens - Position]
The projector can save information about the lens position in memory. Up to three
sets of lens information (including focus, zoom, and lens shift settings) can be
saved, and the lens can be restored to these positions.
Submenu Function
Corner adjustment
Correct image distortion by aligning corners of the blending area with the
image from the reference projector. For multi-projection alignment, align
the corners with the projector blending area (already adjusted) that forms
the basis.
Left, Right,
Top, Bottom
Select the direction of the blending area to adjust. As you
reposition the corners of the selected area, the overall
image changes to match the adjustment.
Submenu Function
Load position 1-3 Restores the lens to the positions saved using Save position 1-3.
Save position 1-3 Saves the lens position as positions 1-3.
Lens shift reset Restores the lens to the original position.
• To lock (protect) the saved position, set [Positional lock] (P105) to [On].
• The values of the following settings are saved in addition to the lens position
information:
-Horizontal/vertical keystone / corner adjustment
-Screen color
-Screen aspect
-Zoom
-Digital image shift
• [Load position] is not available unless you perform [Save position] once.
• The original lens position varies depending on the type of lens used.
• When saved lens positions are restored, images may be projected in a slightly different
position than the saved position.
• Specifying a somewhat smaller image size than the screen size (image area) enables
you to switch among multiple lens positions without having the image extend off the
screen.
• When precise positioning is needed, use lens shift, zoom, and focus functions for fine
adjustment.
Points to adjust
Blending area
• Sides set to an edge-blending width of 12 or more can be
adjusted when [Keystone] is set to [Corner adjustment] and the
aspect ratio is [16:10].
• To reset adjustment, use [Keystone] (P69).
113
Menu Description
Advanced Guide Menu Description
Screen color
> [Install settings] > [Screen color]
You can adjust the color quality of the images projected according to the color of
the projection screen.
On screen
> [Install settings] > [On screen]
Specify display details for on-screen menus, help, and warning or precaution icons.
Submenu Function
Normal Select this if a standard type of projection screen is used. The images
are projected in a light quality similar to that of natural light.
Greenboard
Select if a dark green surface such as a blackboard is used as the
screen. The color quality similar to [Normal] is obtained on the
greenboard.
Adjust Select to fine-tune red, green and blue.
Menu position
Reposition menu display.
Use the [ ] / [ ] / [ ] / [ ] buttons to move the menu to the desired position.
Guide
Shows the guide screen.
Option Function
Off Hides the guide screen.
On Shows the guide screen.
The guide screen is shown at the following cases.
• No input signal is detected. (P54)
• An invalid button is pressed in [BLANK], [FREEZE], or [D.ZOOM] mode. (P35)
• When positional lock (P105) is set to [On] and buttons locked by this feature are
pressed.
• When the projector is already on and the POWER button is pressed.
Menu Description
114
Show input status
Specify whether signal status is shown when there is no signal or when you are completing
signal settings.
Option Function
Off The input status is not displayed.
On The input status is displayed.
Overheat warning display
Specify whether the icon warning of high temperature ( ) is shown when the internal
temperature is high and the projector may overheat.
Option Function
Off Disable high temperature warning icon display.
On Enable high temperature warning icon display.
Menu display time
Extend menu display from the standard 10 or 30 seconds to 3 minutes.
Option Function
Normal The menu is displayed for 10 or 30 seconds.
Extended The menu is displayed for 3 minutes.
The following display times are also changed.
Item [Normal] [Extended]
- MENU screen
- Power-Saving Settings (P73)30 seconds 3 minutes
- Input (P56)
- Keystone adjustment (P67)
- Keystone reset (P69)
- Focus adjustment (P59)
- Zoom adjustment (P60)
- Lens shift adjustment (P61)
- Lens shift reset (P62)
- D.image shift adjustment (P64)
- D.image shift reset (P65)
- Aspect (P65)
- Image mode (P70)
- Volume adjustment (P74)
- Gamma correction (P98)
10 seconds 3 minutes
115
Menu Description
Advanced Guide Menu Description
Test pattern
> [Install settings] > [Test pattern]
You can project a test pattern (P187) to check resolution, color, and other details
even without supplying an input signal.
Lamp warning display
Specify whether to show a lamp replacement message after the lamp has been used for a
specified period.
Option Function
Off The prepare lamp message and the lamp warning are not displayed.
On The prepare lamp message and the lamp warning are displayed.
Air filter warning display
A message advising you to perform cleaning can be set to display when the filter needs
cleaning.
Option Function
Off The air filter warning is not displayed.
On The air filter warning is displayed.
Split screen ID display
Specify whether to show the digit (1 or 2) identifying screens in split-screen mode. Note that
even if [Off] is selected, corner markers will be shown to indicate the side with control rights.
Option Function
Off Hides the screen ID.
On Shows the screen ID.
Option Function
Off Disable test pattern display.
On Enable test pattern display.
• While the test pattern menu is displayed, you can use the [ ] / [ ] buttons to switch
patterns. Additionally, options of test pattern that have options can be changed with the
[ ] / [ ] buttons.
• The test pattern menu is no longer displayed after a little while, but you can view it
again by pressing the [ ] / [ ] buttons.
• When it is almost time to replace the lamp, the projector’s [LAMP] indicator will
flash. For details, see “LED Indicator Displays” (P32).
• Setting display to [Off] will disable both the message to prepare a replacement lamp
and the warning to replace the lamp. To review the replacement timing, check the
lamp counter (P125).
• Lamps that are still used after the timing for lamp replacement are more likely to
rupture. Replace the lamp with a new one as soon as possible.
Setting [Air filter warning display] to [Off] will disable display of the warning to clean
the air filter. We recommend checking the air filter counter (P126) occasionally to
know when to replace the filter.
Menu Description
116
System settings
Customize projector and remote control operation, beeping, and other
details after startup, during standby, and in other situations.
(When the input signal is Analog PC-1)
Menu Function Details
User screen settings Customize user screens shown at startup, when no
signal is detected, and in other situations. P117
Interface settings Specify interface details such as settings for input
signals of connected equipment. P118
Power management
mode
You can specify to turn the lamp or projector off
automatically after a certain period if the projector and
remote control are not used, or if there is no input
signal.
P121
Power management
duration
Specify how long before the lamp is turned off or the
projector enters standby, depending on the [Power
management mode] setting.
P122
Direct power on You can turn on the projector by connecting the power
cable without pressing the POWER button. P122
Beep You can select whether a beep sounds or not when you
operate the projector. P122
Motion blur reduction
Motion blur is blurring that occurs during video
playback. Motion blur reduction can make this blurring
less noticeable.
P123
Language You can select the language in which the menus are
displayed. P123
Other settings
Set a password, reset counters for lamp or air filter
replacement, and access other settings and
information.
P124
117
Menu Description
Advanced Guide Menu Description
User screen settings
> [System settings] > [User screen settings]
Capture a logo and specify logo display settings.
Logo capture
Registers the current image as a user logo. Registered user logos can be shown when no
signal is received, when the BLANK button is pressed, or as the startup image.
Option Function
OK
Display the image for logo registration.
Align the image with the red boundary lines indicating the portion that
will be stored, and then press the OK button. The portion of the image
within the boundary lines is now registered.
Cancel Cancels logo registration.
Logo position
Specify the position of registered user logos as follows.
You can specify the position after a logo has been registered. Choose from upper left, upper
right, center, lower left, or lower right.
No signal screen
Customize the screen shown when no input signals are received.
Option Function
Black The screen is all black.
Blue The screen is all blue.
User logo The user logo is projected.
Screen when blank
Select the screen shown when projection is temporarily blanked out by pressing the BLANK
button on the remote control.
Option Function
Black The screen is all black.
Blue The screen is all blue.
User logo The user logo is projected.
Only images at an aspect ratio of 16:10 can be registered as user logos.
Menu Description
118
Interface settings
> [System settings] > [Interface settings]
Specify interface details such as settings for input signals of connected equipment.
Projector on
Select a logo to project after startup until input signals can be projected.
Option Function
Skip A black screen is projected.
Canon logo Displays the Canon logo that was registered in advance at the factory.
User logo The user logo is projected.
Key repeat
Key repeat enables projector or remote control buttons to be held down instead of pressing
them repeatedly.
Option Function
Off Key repeat is not enabled.
On Key repeat is enabled.
Key lock
Lock the projector to prevent direct or remote control operation.
Option Function
Off Disables the key lock.
Main unit Operation is not possible using the main unit.
Use the remote control.
Remote (wireless)
Disables infrared remote control operations (P38). Use buttons on the
main unit.
Operation is also possible with an optional wired remote control (RS-
RC05).
119
Menu Description
Advanced Guide Menu Description
Remote control channel
Separate channels can be assigned to up to four projectors so that a single remote control
can be used with each projector.
Selecting the Projector Channel
If an optional wired remote control (RS-RC05) is used, there is no need to set the remote
control channel.
Option Function
Ch1
Ch2
Ch3
Ch4
Select the remote control channel to use with this projector.
Independent Can be controlled from a remote control set to any channel.
Selecting a Channel on the Remote Control
After changing the projector channel from the menu, always change the remote control
channel accordingly.
Audio in terminal select
Select the source terminal for audio output.
Option Function
Off No audio is output.
Audio in 1 Use audio signals from AUDIO IN 1 for audio output.
Audio in 2 Use audio signals from AUDIO IN 2 for audio output.
HDMI Use HDMI audio signals for audio output.
HDBaseT Use HDBaseT audio signals for audio output.
LAN
Use LAN audio signals for audio output. Audio is transferred by the
NMPJ application.
To Unlock Key Lock Function
Turn off the projector and unplug the power plug. Hold down the OK button on the main unit
and plug in the power cord, as you continue to hold down the OK button. In a moment, a
beep will sound, and the controls will be unlocked.
When you access this setting from the projector’s side controls, [Main unit] is not
available. Similarly, when you access the setting from the remote control, [Remote
(wireless)] is not available.
Ch1 Hold both the OK button and [ ] button for 3 seconds.
Ch2 Hold both the OK button and [ ] button for 3 seconds.
Ch3 Hold both the OK button and [ ] button for 3 seconds.
Ch4 Hold both the OK button and [ ] button for 3 seconds.
Independent Hold both the OK button and MENU button for 3 seconds.
Audio is transferred via the port selected in [Communication
settings] > [Wired network] (P120).
Menu Description
120
HDBaseT
Enable or disable HDBaseT. Refer to the following sections for details on HDBaseT
connections. For video/audio details, see “Connection Procedure” (P50, P51). For network
details, see “Connection Methods” (P127).
Option Function
Off Disable HDBaseT.
On Enable HDBaseT.
Image signal
quality
The HDBaseT input signal value received is indicated by a white line.
High Indicated by the green portion. This is the recommended
level.
Middle Indicated by the yellow portion. The signal is fluctuating.
Check the cable.
Low Indicated by the red portion. The signal cannot be used. Fix
the cable connection or replace the cable.
Communication settings
Select ports used for serial communication and network connections. Otherwise, you can
refer to this setting to check setting values for the port selected for serial communication.
Submenu Function
Serial
communication
Service port Use the service port (CONTROL).
HDBaseT Use the HDBaseT port.
Details
Wired network LAN port Use the LAN port.
HDBaseT Use the HDBaseT port.
Do not coil or bundle cables.
Option Function
Baud rate Modulation rate, in bits per second.
Data bits Number of bits of data.
Parity Number of parity bits.
Stop bit Length of mark representing the end of data bits.
Select 1 or 2.
• [HDBaseT] is not available when [HDBaseT] is set to [Off].
• [Wired network] is not available when [Network function] (P131) is set to [Off].
• Changes to the wired network setting do not take effect immediately. To apply [Wired
network] settings, restart the projector.
121
Menu Description
Advanced Guide Menu Description
Power management mode
> [System settings] > [Power management mode]
You can specify to turn the lamp or projector off automatically after a certain period
if the projector and remote control are not used, or if there is no input signal.
HDMI image input
Set the type of equipment which is connected to the HDMI port. Note that to some extent, the
[HDMI image input] setting determines which image modes are available. (P70)
Option Function
Auto Select when AV equipment will be connected. Image processing, menu
displays, and other elements are adjusted for video equipment.
Computer Select when a computer will be connected. Image processing, menu
displays, and other elements are adjusted for a computer.
HDBaseT image input
Specify the type of equipment connected to the HDBaseT port. Note that to some extent, the
[HDBaseT image input] setting determines which image modes are available. (P70)
Option Function
Auto Select when AV equipment will be connected. Image processing, menu
displays, and other elements are adjusted for video equipment.
Computer Select when a computer will be connected. Image processing, menu
displays, and other elements are adjusted for a computer.
Option Function
Disabled Disable power management mode.
Lamp off Only turns the lamp off.
Standby Turns the projector off and puts it in standby.
• Projection resumes when the same input signal is restored, when the remote control or
projector is operated, or when a user command to activate the projector is received.
• After the projector enters standby, restoring projection requires the same steps as when
turning the projector on normally.
• When [Disabled] is selected, [Direct power on] (P122) is not available.
• This setting can also be adjusted from the power saver settings screen by pressing the
LAMP button on the remote control.
Menu Description
122
Power management duration
> [System settings] > [Power management duration]
Specify how long before the lamp is turned off or the projector enters standby,
depending on the [Power management mode] setting.
Direct power on
> [System settings] > [Direct power on]
You can turn on the projector by connecting the power cable without pressing the
POWER button.
Beep
> [System settings] > [Beep]
You can select whether a beep sounds or not when you operate the projector.
Option Function
5 min. - 60 min. After 30 seconds without an input signal when the projector is idle,
the projector starts displaying a countdown of the selected time.
• If conditions that would start countdown are met while you are blanking projection,
blanking is canceled.
• Once countdown begins, audio output stops.
Option Function
Off The POWER button must be pressed to turn the projector on.
On You can turn on the projector by connecting the power cable only.
• Before enabling direct power on, be sure to set [Power management mode] to an
option other than [Disabled]. When [Disabled] is selected, [Direct power on] is not
available.
• After turning off the projector, wait at least 5 minutes before turning it on again. It may
shorten the lamp life if you turn on the projector immediately after turning it off.
• The projector is also equipped with a Direct Power Off feature. No damage is caused to
the projector even if it is unplugged during projection to turn it off without pressing the
POWER button. However, setting adjustments made immediately before unplugging
the projector may not be stored.
Option Function
Off Disables the beep.
On Enables the beep.
The beep will not sound if you mute the projector sound with the MUTE button on the
remote control.
123
Menu Description
Advanced Guide Menu Description
Motion blur reduction
> [System settings] > [Motion blur reduction]
Motion blur is blurring that occurs during video playback. Motion blur reduction can
make this blurring less noticeable.
Language
> [System settings] > [Language]
Select the menu display language.
Option Function
Off Motion blur reduction is not performed.
On Motion blur reduction is performed.
• If reducing motion blur produces distracting image noise, select [Off].
• Effects of motion blur reduction cannot be checked during menu display.
• Especially effective for motion of computer graphics and similar high-resolution images.
• This feature is not available during LAN/USB input.
Language
English Russian Czech
German Dutch Danish
French Finnish Arabic
Italian Norwegian Chinese (Simplified)
Spanish Turkish Chinese (Traditional)
Portuguese Polish Korean
Swedish Hungarian Japanese
Menu Description
124
Other settings
> [System settings] > [Other settings]
Lock operation with a password, set a password, reset counters for lamp or air filter
replacement, and access other settings and information.
Password settings
Disables the projector unless the correct password is entered.
Option Function
Off The projector can be used even if no password is entered.
On The projector cannot be used unless you enter your password.
To Cancel the Password
Cancellation
on the
Projector
Turn off the projector and unplug the power plug.
Hold down the MENU button on the side control and connect the power
plug. Make sure to keep holding down the MENU button until a beep
sounds. When the projector beeps, the password is canceled. (The
entered password is also reset.)
Cancellation
on the Remote
Control
To forcibly cancel the password from the remote control, in standby state
press the MENU button 3 times, then press the POWER button.
• You cannot set [On] unless you have completed [Register password].
Once you set a password, the password entry screen appears at power-on.
Enter a 4 digit password.
Enter the password using the [ ] / [ ] / [ ] / [ ] buttons.
If the password is valid, the projection starts. If you enter a wrong password three times,
the power will be turned off.
• The projector also goes off after three minutes of inactivity on the password input
screen.
125
Menu Description
Advanced Guide Menu Description
Register password
You can register a password for starting projection.
Enter a 4 digit password.
Enter the password using the [ ] / [ ] / [ ] / [ ] buttons.
The 4-digit password is entered from the left to right digits. When the final digit is entered, the
password is automatically registered.
Press the MENU button to abort the registration.
[Fn] button settings
You can select a function to be assigned to the Fn button on a remote control.
Option Function
Disable Disables assigning a function to the Fn button on the remote control.
Split screen Enables split-screen mode toggling using the Fn button on the remote
control.
Gamma restore
Restore the original gamma if, after the projector has been used for some time, you notice
that tone curves have changed, or if neutral colors have become tinted. Gamma restore can
only be used when the lamp has been on for approximately 30 minutes or longer.
Submenu Function
Off Returns to the factory default without performing Gamma restore.
Adjust Restore the original gamma and apply the result.
Lamp counter
You can reset the lamp counter that indicates the time for lamp replacement.
For details on lamp counter display, see “Replacing the Lamp” (P173).
Select the function to assign to the Fn button of a remote control (RS-RC05, sold
separately).
• If Gamma restore is performed, the tone characteristics and achromatic color will be
restored as close as possible to the condition when the projector was purchased,
however it is not possible to restore it completely to the original condition.
• If Gamma restore is performed, the adjustment screen will be projected for
approximately 150 seconds.
• To cancel Gamma restore, press the POWER button.
• Do not reset the lamp counter except when you have replaced the lamp. Otherwise,
the lamp counter cannot indicate the correct timing for replacing the lamp.
• Lamps are more likely to rupture once the lamp replacement message has been
displayed (P173). Replace the lamp with a new one as soon as possible.
• The lamp counter provides an estimate of the time remaining until the lamp must be
replaced. This value is based on the hours in use and the present load on the lamp.
• The number of hours indicated is equivalent to use under these conditions: [Vertical
projection] (P108) set to [Off], and [Lamp mode] (P102) set to [Full power].
Menu Description
126
Air filter counter
This resets the counter which reminds you of the time for cleaning and replacing the air filter.
Power counter
Indicates the total time that the projector has been connected to a power supply.
Firmware
Update the projector firmware.
Check the version indicated before updating the firmware.
Update the projector firmware as follows.
1. Download updated firmware from the Canon website and store it at the root directory on a
USB flash drive.
2. Insert the USB flash drive in the USB port.
3. Follow the instructions shown to complete the update process.
Factory defaults
You can reset the menu item settings and restore the system settings to the factory defaults.
Option Function
OK Settings are reset to default.
Cancel Settings are not reset to default.
For details on replacing or cleaning the filter, see P171 - P172.
This value is not reset even if [Factory defaults] is executed.
• Firmware versions shown here are for illustration only and differ from actual
versions.
• In some cases, it may not be possible to download updates. For details, contact the
Canon Customer Support Center.
• Firmware updating takes a few minutes. During the update, the LED indicator will
flash in red. Do not turn off the projector while the LED is flashing. After the update,
the projector will automatically turn itself off and enter standby mode.
127
Menu Description
Advanced Guide Menu Description
Network settings
Network Connection Overview
Connecting the projector to a network enables you to control the projector from a
computer and receive notification of projector errors via email.
Depending on the method of network connection, preparation on the computer side
may be necessary. The following is an explanation of preparation on the computer
side.
Connection Methods
To connect the projector to a computer network, use a LAN cable. The LAN cable
can be connected to either the LAN port or HDBaseT port.
When using the LAN port, connect the projector as follows.
When using the HDBaseT port, connect the projector as follows.
•The LAN port and HDBaseT port cannot be used at the same time for a network
connection.
•Network connectivity provided by the HDBaseT port and LAN port is identical,
except that the HDBaseT provides a maximum transfer speed of 100 Mbps.
•When the [Network function] setting of the projector is set to [Off] (Network
Connections is disabled), switch it to [On] to enable it. (P131)
•Select which port to use in [Communication settings] > [Wired network] (P120).
•Referring to “Checking Projector Information” (P156), confirm that the projector’s
IP address is not the same as that of other computers on the network. To set a
projector IP address, follow the instructions in “Controlling the Projector from a
Computer” (P154) and use the web screen, or use projector TCP/IP settings.
(P132)
LAN cable (shielded twisted pair;
not included)
Hub or router, etc. LAN terminal
LAN cable
(CAT5e or better,
shielded-compatible;
sold separately)
LAN cable
(CAT5e or better,
shielded-compatible;
sold separately)
HDBaseT
port
HDBaseT
transmitter
Menu Description
128
•When you connect the computer to the network for the first time, it is also
necessary to perform settings on the computer. In this case, consult the network
administrator regarding the necessary settings.
In a network environment where a DHCP server is operating, choose [On] on the
projector [DHCP] screen to enable the DHCP function and connect it. (P132)
129
Menu Description
Advanced Guide Menu Description
Completing Projector Settings
Settings described in this section apply to the network connections, setting a
network password, and other aspects of networked projection.
(When the input signal is Analog PC-1)
Menu Function Details
Network settings lock Lock network settings to prevent changes. P130
Network password
setting
Activate or deactivate password protection for network
settings. P130
Register network
password Set a network password. P130
Network standby settings Specify the extent of network functionality in standby
mode. P131
Network function You can turn the projector network function on or off. P131
Detailed settings Display and set advanced settings for network
connections. P132
PJLink Enable or disable PJLink. P134
AMX Device Discovery Enable or disable AMX Device Discovery. P135
Crestron RoomView Enable or disable Crestron RoomView. P135
Menu Description
130
Network settings lock
> [Network Settings] > [Network settings lock]
You can lock/unlock the network settings so that they cannot be changed.
Network password setting
> [Network settings] > [Network password setting]
You can set whether or not a password is required in order to change the projector
network settings.
Register network password
> [Network settings] > [Register network password]
Use the [ ] / [ ] / [ ] / [ ] buttons to enter the projector network password.
Option Function
Unlock
Cancels the lock and allows other network settings to be changed. The
password must be entered in order to cancel the lock. Use the [ ] / [ ] /
[ ] / [ ] buttons to enter the 4-digit password.
Lock Lock the settings.
•Forcibly canceling the network lock
Press these buttons in the following order to cancel the lock: [ ] [OK] [ ] [OK] [ ]
[OK]. This operation resets the network password to [ ] [ ] [ ] [ ].
• Setting [Network password setting] to [Off] leaves network settings unlocked.
Option Function
Off A network password is not used.
On A network password is used.
131
Menu Description
Advanced Guide Menu Description
Network standby settings
> [Network settings] > [Network standby settings]
Specify the network function operating status in standby mode as follows.
Network function
> [Network settings] > [Network function]
Enable or disable network function.
Specifying [Off] can save energy.
Option Function
Normal All network functions are available even in standby mode,
including the web screen, control over the network, and PJLink.
Low-power
All network functions are available even in standby mode.
However, the projector may be less responsive than usual when
some functions are initially used.
• [Low-power] may delay access over the network for some functions. For faster access,
select [Normal].
• Power consumption when Network function is [On] varies depending on whether
Network standby settings is set to Normal or Low-power.
• This setting can also be adjusted from the power saver settings screen by pressing the
LAMP button on the remote control.
Option Function
Off Disable the network function.
On Enable the network function.
Menu Description
132
Detailed settings
> [Network settings] > [Detailed settings]
Display and manually change the IP address, gateway address, and other settings.
Available only when the network function is [On].
Menu Function
IP address IP address of the projector.
Gateway address Gateway address of the projector.
MAC address MAC address of the projector.
DHCP
TCP/IP settings
Change or specify the IP address, subnet mask, and gateway address
used for connections.
Option Function
Off Disables the DHCP function. TCP/IP settings must be
configured manually.
On
Enables the DHCP function. Searches the DHCP
server. There is no need to configure TCP/IP settings
(IP address, subnet mask, and gateway address),
because the IP address is acquired from the DHCP
server.
• This menu is not available (grayed out) when [DHCP] is [On].
• If an invalid value is entered, the message “Invalid entry”
appears. If this occurs, enter a valid value.
133
Menu Description
Advanced Guide Menu Description
Network setting
initialization
The following network settings are initialized.
Settings configured from the projector menu
•Network settings lock (P130)
•Network password setting (P130)
•Register network password (P130)
•Network standby settings (P131)
•Network function (P131)
•Detailed settings(P132)
•PJLink (P134)
•AMX Device Discovery (P135)
•Crestron RoomView (P135)
Settings configured from the web screen
•[Password] (P143)
•[Network] (P144)
•[NMPJ Password] (P145)
•[Mail] (P146)
•[Mail auth] (P147)
•[SNMP] (P148)
•[Projector info.] (P149)
•[PJLink] (P150)
Menu Function
Menu Description
134
PJLink
> [Network settings] > [PJLink]
You can enable or disable the PJLink network function of the projector.
When this function is enabled, control is possible over a network using PJLink
commands.
Option Function
Off Disables the PJLink function.
On Enables the PJLink function.
• The projector conforms to Class 1 as defined in PJLink standards established by the
Japan Business Machine and Information System Industries Association (JBMIA). This
projector supports all commands that are defined by PJLink Class 1, and has been
verified as conforming to the PJLink standard Class 1 definition.
• For details on using PJLink, see “Setting PJLink [PJLink]” (P150).
What is PJLink?
In September 2003, the PJLink Working Group was established under the Data Projector
Committee. During the first year, this PJLink Working Group standardized PJLink as a new
interface specification for projectors.
PJLink is a unified standard for operation and control of projectors.
It allows centralized control of projectors and operation from a controller for all projectors
regardless of manufacturer.
The objective is for JBMIA to improve convenience for users and expand the use of
projectors through early systemization for network monitoring and control of projectors,
which will become the mainstream in the future.
Class 1: Standardization of control and monitoring specifications for basic projector
functions
Basic projector control: Power control, input selection, etc.
Acquisition of projector information and status: Power status, input selection status, error
status, lamp use time, etc.
JBMIA: Japan Business Machine and Information System Industries Association.
The JBMIA is an organization which was launched in 1960 and changed its name
on April 1, 2002.
PJLink website: http://pjlink.jbmia.or.jp/english/
PJLink is a registered trademark of JBMIA and pending trademark in some countries.
PJLink is a registered trademark, or an application has been submitted for trademark, in Japan,
the United States and / or other countries or regions.
135
Menu Description
Advanced Guide Menu Description
AMX Device Discovery
> [Network settings] > [AMX Device Discovery]
In a network environment, AMX Device Discovery can be used to enable other
equipment to discover the projector. For networks without AMX Device Discovery,
select [Off].
Crestron RoomView
> [Network settings] > [Crestron RoomView]
Crestron RoomView enables centralized management of multiple projectors over a
network. Networked projectors can be remotely controlled to troubleshoot issues,
check the useful life of lamps, or turn the projectors on or off. Specify whether to
use Crestron RoomView.
Option Function
Off Disables AMX Device Discovery.
On Enables AMX Device Discovery. The projector will periodically send
out AMX beacon packets over the network.
• For details on AMX Device Discovery, visit the AMX website.
http://www.amx.com/
Option Function
Off Disable Crestron RoomView.
On
Enables Crestron RoomView. A port for RoomView will be opened,
and the projector will respond to CIP packets. Communication is
possible via the RoomView Express/Server application or via
Crestron Controller. (P150)
•
For details on Crestron RoomView, visit the Crestron
®
website.
http://www.crestron.com/
Menu Description
136
Completing Computer Settings
Specifying an IP Address
Instructions for setting a computer’s IP address are as follows for each operating
system.
■Windows 10
1Right-click the Start button (Windows logo) in the lower left of the screen.
•In desktop mode (from the desktop screen)
The same operation is possible by pressing Win+X.
2In the shortcut menu displayed in the lower left, click [Control Panel].
3Click [View network status and tasks].
•In Icon View:
Click [Network and Sharing Center].
4Click [Change adapter settings].
5Right-click [Ethernet], and then click [Properties].
6In the [This connection uses the following items] list, select [Internet
Protocol Version 4 (TCP/IPv4)] and click the [Properties] button. Make a
note of the original network settings (IP address, subnet mask, default
gateway, etc).
7Select [Use the following IP address] and set the IP address and subnet
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
8When finished, click the [OK] button, and then click the [Close] button in
the [Ethernet Properties] window to close it.
137
Menu Description
Advanced Guide Menu Description
■Windows 8 / 8.1
1Right-click on the start screen background and click [All Apps] in the
lower right.
•Windows 8.1 Users:
Click the down arrow in the lower left of the start screen.
2Click [Control Panel].
•From the Desktop:
Press Win+X.
In the shortcut menu displayed in the lower left, click [Control Panel].
3Click [View network status and tasks].
•In Icon View:
Click [Network and Sharing Center].
4Click [Change adapter settings].
5Right-click [Ethernet], and then click [Properties].
6In the [This connection uses the following items] list, select [Internet
Protocol Version 4 (TCP/IPv4)] and click the [Properties] button. Make a
note of the original network settings (IP address, subnet mask, default
gateway, etc).
7Select [Use the following IP address] and set the IP address and subnet
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
8When finished, click the [OK] button, and then click the [Close] button in
the [Ethernet Properties] window to close it.
Menu Description
138
■Windows 7
1From the PC [Start] menu, select [Control Panel].
2Click on [Network and Internet], then click on [View network status and
tasks].
3From the menu on the left side of the window, click on [Change adapter
settings].
4Right-click [Local Area Connection], and open [Properties].
5Select [Internet Protocol Version 4 (TCP/IPv4)] and click the [Properties]
button. Make a note of the original network settings (IP address, subnet
mask, default gateway, etc).
6Select [Use the following IP address] and set the IP address and subnet
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
7When the settings are completed, click the [OK] button and then click the
[OK] button on the [Local Area Connection Properties] window to close it.
■Windows Vista
1From the PC [Start] menu, select [Control Panel].
2Click on [View network status and tasks].
3From the menu on the left side of the window, click on [Manage network
connections].
4Right-click [Local Area Connection], and open [Properties].
5Select [Internet Protocol Version 4 (TCP/IPv4)] and click the [Properties]
button. Make a note of the original network settings (IP address, subnet
mask, default gateway, etc).
6Select [Use the following IP address] and set the IP address and subnet
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
7When the settings are completed, click the [OK] button and then click the
[OK] button on the [Local Area Connection Properties] window to close it.
139
Menu Description
Advanced Guide Menu Description
■Mac OS X
1Open the Apple Menu and select [System Preferences].
2In the System Preferences window, click [Network] to display the Network
window.
3Select [Built-in Ethernet] and click the [TCP/IP] tab. Make a note of the
original network settings (IP address, subnet mask, router, DNS server,
etc.).
4Create a new network environment and set the IP address and subnet
mask.
The factory default IP address for the projector is “192.168.254.254”. Set an IP
address which is different from this.
5Click [Apply] to close the network preference window.
■Resetting the IP Address Setting of the Computer
Follow the same procedure as for changing the IP address and reset the values to
the original values based on the notes taken before the change.
Setting Up the Network
■Displaying the Network Configuration Screen
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the
address bar, and press the Enter key.
The projector web screen appears.
Network functions are not available for the first 40 seconds after projector startup.
Menu Description
140
The following information is displayed.
* For details on downloading the Networked Multi-Projection (NMPJ) application,
refer to the NMPJ user’s manual.
3Click [Settings] on the web screen.
The password input window appears.
Network Multiple Projection
Download
For downloading the Networked Multi-Projection
(NMPJ) program.*
Projector control Displays the projector control screen.
Settings Shows the settings screen.
Projector name The name of the projector on the network
Comment Relevant notes, such as where the projector is installed
MAC address The MAC address of the projector
IP address The IP address of the projector
PowerStatus The power status of the projector
LampModeFullPower Lamp operating time in [Full power] lamp mode
LampModePowerSaver Lamp operating time in [Power saver] lamp mode
LampTimeConverted Lamp operating time (converted value)
FilterTime Air filter operating time
Alert Error message (if an error has occurred)
Temperature abnormality
Faulty lamp
Faulty cooling fan
Faulty air filter unit
Faulty power supply
Faulty lens connector
Unknown error
The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the
network administrator for the projector IP address. It is possible to check the IP address
from the projector menu. (P132)
141
Menu Description
Advanced Guide Menu Description
4Enter the user name and password on the password input window, then
click [OK].
The factory default user name is “root” and the password is “system”.
The settings screen is displayed. Complete the network settings on this screen.
■Network Setting
1Select a function to set up from the settings screen menu.
To control the projector from the computer, click [Projector control]. (P154)
Menu Description
142
2Enter setting details in the fields shown (1), and then click [OK] (2).
3A confirmation window appears. Check the contents and if they are
correct, click [Apply].
The settings are applied to the projector.
Selecting [Network] or [Password] in the menu will cause this message to be
displayed: “Save completed. Please change setting and reconnect.”
If you select functions other than above, “Save completed” is displayed. Click
[Back to top] to return to the top page of the web screen.
(1)
(2)
143
Menu Description
Advanced Guide Menu Description
Setting a Password [Password]
From [Password] in the settings screen, you can set a user name and password for
web screen login. For the setting procedure, refer to “Network Setting” (P141).
Item Explanation Factory default setting
User name When logging into the web screen,
enter the user name in 1-byte
alphanumeric characters and symbols
(4 -15 characters).
root
New password When logging into the web screen,
enter the password in 1-byte
alphanumeric characters and symbols
(4 -15 characters).
system
Confirm new password For confirmation, enter the same
password that you entered in [New
password].
system
Menu Description
144
Setting Basic Information [Network]
From [Network] in the settings screen, you can log into the web screen and set
basic network information. For the setting procedure, refer to “Network Setting”
(P141).
Item Explanation Factory default setting
MAC address Shows the projector’s MAC address. The MAC address of the
projector
DHCP Select whether to turn the DHCP
function on or off. The following settings
cannot be configured manually when
this setting is [ON], because the IP
address is acquired from the server.
[IP address]
[Subnet mask]
[Default gateway]
OFF
IP address Enter the IP address of the projector in
1-byte numbers.
192.168.254.254
Subnet mask Enter the subnet mask in 1-byte
numbers.
255.255.255.0
Default gateway Enter the default gateway IP address in
1-byte numbers.
0.0.0.0
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to
the network.
If the network subnet mask was changed, select [Subnet mask] in the above screen and
set the new subnet mask.
145
Menu Description
Advanced Guide Menu Description
Specifying Networked Multi-Projection Settings [NMPJ Password]
From [NMPJ Password] in the settings screen, you can specify the items needed
for NMPJ authentication. For the setting procedure, refer to “Network Setting”
(P141).
Item Explanation Factory default setting
Password Enter the password required for a
networked multi-projection connection
in single-byte alphanumeric characters
(0-15 characters).
<Blank>
Confirm password For confirmation, enter the same
password as you entered in [Password].
<Blank>
For details on Networked Multi-Projection (NMPJ), refer to the NMPJ user’s manual.
Menu Description
146
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error
mails and test mails. For the setting procedure, refer to “Network Setting” (P141).
* When the interval is set to 0 seconds, repeated attempts to send mail are made
(as set in [Mail resend times]) without pausing between attempts.
Item Explanation Factory default setting
To:
Enter the recipient address for error mails
in 1-byte alphanumeric characters and
symbols (1 - 63 characters).
MailUserAccount
Cc:
Enter the CC address for error mails in 1-
byte alphanumeric characters and symbols
(1 - 63 characters).
<Blank>
From:
Enter the sender address for error mails
in 1-byte alphanumeric characters and
symbols (1 - 63 characters).
Projector@canon.co.jp
SMTP server IP address Enter the SMTP server IP address in 1-
byte numbers.
0.0.0.0
SMTP server port
number
Enter the SMTP server port number in 1-
byte numbers (1 - 65535).
25
SNTP server IP address Enter the SNTP server IP address in 1-
byte numbers.
0.0.0.0
Time zone Select the time zone where the
projector is used.
(GMT) Dublin, Lisbon,
London
Mail resend interval* Enter the interval for resending mail
when an error occurred (unit: seconds)
within the range of 0 - 59 seconds using
1-byte numbers.
10
Mail resend times Enter the number of times to resend
mail when an error occurred within the
range of 0 - 255 using 1-byte numbers.
3
Error report Select whether to turn the error mail
sending function on or off.
OFF
147
Menu Description
Advanced Guide Menu Description
Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings screen, you can configure the settings for
authentication of mail that is sent when an error occurs. For the setting procedure,
refer to “Network Setting” (P141).
Item Explanation Factory default setting
Mail authentication Select the mail authentication method.
If OFF is selected, the other mail
authentication settings cannot be
changed.
OFF
User name
Enter the user name to use for mail
authentication in 1-byte alphanumeric
characters and symbols (1 - 63
characters).
<Blank>
Password
Enter the password for mail
authentication in 1-byte alphanumeric
characters and symbols (1 - 63
characters).
<Blank>
Confirm password For confirmation, enter the same
password as you entered in
[Password].
<Blank>
POP3 server IP
address
Enter the POP3 server IP address in 1-
byte numbers.
0.0.0.0
POP3 server port
number
Enter the POP3 server port number in
1-byte numbers (1 - 65535).
110
POP before SMTP
response time
Enter the SMTP authentication timeout
period after POP3 authentication (unit:
milliseconds) using 1-byte numbers (0 -
9999 milliseconds).
300
Menu Description
148
Sending a Test Mail [Send test mail]
From [Send test mail] in the settings screen, you can send a test mail to the mail
address that was set in [Mail]. The settings cannot be changed from this screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to
control of projectors which use SNMP (Simple Network Management Protocol). For
the setting procedure, refer to “Network Setting” (P141).
Item Explanation
To: The recipient address which was set from [Mail] in the settings screen (P146) is
displayed.
Cc: The CC address which was set from [Mail] in the settings screen (P146) is
displayed.
From: The sender address which was set from [Mail] in the settings screen (P146) is
displayed.
Subject: The predetermined mail title “Canon Projector test” is displayed.
149
Menu Description
Advanced Guide Menu Description
Setting Projector Information [Projector info.]
From [Projector info.] in the settings screen, you can enter relevant comments such
as projector names and locations where projectors are installed so that the
information can be used to identify projectors when multiple projectors are installed
on the network. For the setting procedure, refer to “Network Setting” (P141).
Item Explanation Factory default setting
SNMP Select the SNMP function version. If
OFF is selected, the SNMP function will
be turned off and the other settings in
this screen cannot be changed.
OFF
Receive community Enter the community name which will
receive projector information in 1-byte
alphanumeric characters and symbols
(1 - 15 characters).
<Blank>
Password Enter the community settings password
in 1-byte alphanumeric characters and
symbols (8 - 15 characters). It can be
set only when the SNMP version is V3.
<Blank>
Confirm password For confirmation, enter the same
password as you entered in [Password].
<Blank>
Item Explanation Factory default setting
Projector name Enter the projector name in 1-byte
alphanumeric characters and symbols
(1 - 63 characters).
Canon Projector001
Comment
Enter any relevant notes, such as where
the projector is installed.
<Blank>
Some characters such as # cannot be used for [Projector name] and [Comment].
Menu Description
150
Setting PJLink [PJLink]
From [PJLink] in the settings screen, you can set the PJLink functions which are the
standard for projector management on a network. For the setting procedure, refer
to “Network Setting” (P141). For information about PJLink, refer to “What is
PJLink?” (P134).
Setting Up a Controller Manufactured by Crestron Electronics
[Crestron Controller]
The [Crestron e-Control] screen will open. For details on the Crestron Controller,
visit the Crestron website.
http://www.crestron.com/
Item Explanation Factory default setting
PJLink Turn the PJLink function on or off. If
OFF is selected, the PJLink function
will be turned off and the other settings
in this screen cannot be changed.
ON
PJLink authentication Select whether to turn the PJLink
authentication function on or off. The
following settings cannot be changed
when this setting is [OFF].
[Password]
[Confirm password]
ON
Password Enter the PJLink authentication
password in 1-byte alphanumeric
characters (1 - 32 characters).
system
Confirm password For confirmation, enter the same
password that you entered in
[Password].
system
151
Menu Description
Advanced Guide Menu Description
Setting Errors
When a setting-related error occurs, the error name is displayed on the screen, and
a “!” mark is displayed next to the input field which caused the error.
The error meanings are as shown below.
Error Meaning
Input error A setting outside the valid range was set on the
settings screen.
Password setting error The set password and confirmation password did
not match.
Invalid SMTP The SMTP server IP address has not been set.
System failed to connect SMTP server. Failed to connect to the SMTP server when
sending a test mail.
System failed to connect POP3 server. Failed to connect to the POP3 server attempting
to send a test mail.
System doesn’t support this auth type. An authentication type was set which is not
supported by the server.
System failed to authenticate. Authentication failed attempting to send a test
mail.
The system failed to send the test mail. Sending of test mail failed due to a connection
failure with the SMTP server or an error which
does not ordinarily occur.
Unknown error Unknown error
153
Menu Description
Advanced Guide Menu Description
■Error Notification Mails
The messages shown in the following error list are sent when an error occurs in the
projector.
Error list
Errors related to
temperature
Error name Temperature abnormality
Text The temperature inside the projector is too high for some
reason or the outside air temperature is higher than the
specified one.
If the problem is inside the projector, check whether the
projector is installed and operated normally, turn off the
projector to cool its inside, and retry projection. If the
same warning occurs again, the projector may be
defective. Contact your dealer.
Errors related to
the lamp
Error name Faulty lamp
Text The lamp has burnt out. Replace the lamp with a new
one. If the same warning occurs again, the lamp drive
circuit may be defective. Contact your dealer.
Errors related to
the fan
Error name Faulty cooling fan
Text The cooling fan or another component may be defective.
Contact your dealer.
Errors related to
the air filter
Error name Faulty air filter unit
Text The air filter unit is not installed properly.
Check whether the air filter unit is installed properly.
If it is installed properly, the air filter unit detection switch
may be defective. Contact your dealer.
Errors related to
the power
Error name Faulty power supply
Text The voltage of part of the power supply is abnormally high
or any other problem has occurred in the power supply.
Contact your dealer.
Errors related to
the lens
connector
Error name Faulty lens connector
Text The lens cable is not connected to the lens unit. Check
whether the lens cable is connected to the lens unit
properly. If it is connected properly, the lens connector or
cable may be defective. Contact your dealer.
Menu Description
154
Controlling the Projector from a Computer
When the projector is connected to a network, it is possible to control the projector
from a computer via the network.
1Turn on the computer and projector.
2Launch a web browser, enter “http://(projector IP address)” in the
address bar, and press the Enter key.
The projector web screen appears.
3Click [Projector control] on the web screen.
The password input window appears.
4Enter the user name and password on the password input window, then
click [OK].
The factory default user name is “root” and the password is “system”.
The projector control screen appears.
The projector can be controlled from this screen.
The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the
network administrator for the projector IP address. It is possible to check the IP address
from the projector menu.
Item Explanation
Projector name The name of the connected projector is displayed. (P149)
Comment Shows notes, such as where the projector is installed. (P149)
Refresh Refreshes the displayed contents with the most recent information.
Power Turns projector power on or off.
Input Select an input signal and click [Apply] to change to that input signal.
(P56)
Aspect Select an aspect and click [Apply] to change to that aspect. (P65)
Image mode Select an image mode and click [Apply] to change to that image mode.
(P70)
Blank Switches the blank setting on or off. (P72)
Mute Switches the mute setting on or off. (P36)
Auto PC Click [Apply] to perform Auto PC adjustment. (P58)
155
Menu Description
Advanced Guide Menu Description
5When the operations are finished, click [Back to top] to return the initial
web screen.
Split screen Select the setting for split-screen mode and click [Apply] to switch to
split-screen projection.
Split screen
control
Select the control rights setting for split-screen mode and click [Apply]
to switch the side currently under control.
Information The control results and control error information are displayed at the
top of the screen.
Item Explanation
Menu Description
156
Checking Projector Information
You can check information about the signal types of the images projected
and other information.
* The values are not displayed when network functions are [Off].
Menu Function
Model name Shows the model name.
Input signal
Details of the input signal currently selected
Information such as the type, resolution, frequency, and color
format of the signal is displayed.
Firmware Current firmware version
Serial no. Serial number unique to this projector
Projector usage time Shows the total time the projector has been on.
IP address* IP address used when connected to a network.
E-mail sender address* Sender e-mail address used for sending error mails (P146)
E-mail recipient address* Displays [Already set] or [Not set] to show whether a recipient
e-mail address has been set for receiving error mails. (P146)
Projector name* Name which identifies this projector on the network (P149)
Comments* Comments such as the location in which the projector is installed
are displayed. (P149)
System information ID System information. Normally this is not displayed.
157
Advanced Guide Advanced Projection
Advanced Projection
Projecting Images on a USB Flash Drive
JPEG images stored on a USB flash drive connected to the projector can be
projected as follows. Individual images can be selected for projection, or you can
project all images in a slideshow. JPEG images up to 10912×8640 can be
projected.
1Insert the USB flash drive in the USB port.
Either connect the USB flash drive directly to the projector’s USB port or use a
USB cable to connect a USB multi-card reader. USB flash drives connected via
a USB hub will not be recognized.
2Press the INPUT button to select [USB].
Thumbnails of JPEG files on the USB flash drive are now listed.
• USB flash drives with security features are not recognized by the projector and cannot
be selected as the image source.
• If the projector cannot mount the file system, the drive name is grayed out and the
following icon is displayed. In this case, the USB flash drive cannot be used.
• Up to six USB flash drives, 999 folders, or 9,999 files can be displayed.
• If there are multiple drives, a drive selection screen is displayed. Use the [] / []
buttons to select the desired drive, and then press the OK button. Files on the drive are
now listed.
• On file and drive selection screens, you can switch between thumbnail and list display.
• Network input is not available when [USB] is selected as the other input signal in split-
screen display.
Advanced Projection
158
3Select a file to project.
4Switch to other images as needed.
To switch to the previous image, press the [ ] button.
To switch to the next image, press the [ ] button.
To rotate images left 90°, press the [ ] button.
To rotate images right 90°, press the [ ] button.
5After projection is finished, remove the USB flash drive.
Motion blur reduction is not available when projecting JPEG files on a USB flash drive.
(P123)
The projector can also play a slideshow of images on a USB flash drive automatically.
(P161)
159
Advanced Projection
Advanced Guide Advanced Projection
Description of USB File Browser
If a USB flash memory is connected to the projector, the USB file browser appears.
In the USB file browser, you can select the image file to be projected by operating
the file list in the USB memory device.
(1) List title
Identifies the current USB flash
drive and number of pages in the
file list displayed. (Current page
number/total number of pages)
(2) Drive/file list
Lists recognized USB flash drives
and files in folders on the drive, by
name. Select an image file or
folder with the pointer buttons. The
following icons are shown.
(3) File information area
Information of the image selected
in the file list appears here.
•File name
•File size
•Shoot. d/t
•Image size
•Camera model
•Shoot. cond.
(4) File path area
Path name of the image selected
in the file list appears here.
(5) Preview area (in list view)
Image selected in the Drive/file list
appears with reduced size. is
displayed when an unsupported
JPEG format is selected.
If a folder is currently selected, the
folder icon appears.
Thumbnail view List view
(1)
(2)
(3)
(4)
(1)
(2)
(3)
(4)
(5)
Icon Function
Recognized USB flash drive
Unrecognized USB flash drive (in
thumbnail view)
Unrecognized USB flash drive (in
list view)
No removable media in the card
reader or similar device
Switch to list view (from thumbnail
view)
Switch to thumbnail view (from list
view)
Go to the parent folder
Folder
Unsupported JPEG file (in
thumbnail view)
File or folder names in Arabic are not
displayed correctly.
Advanced Projection
160
Selecting an Image for Projection
This section describes the steps for selecting an image in the USB file browser and
projecting on the screen.
■Selecting a Drive
This step may not be necessary when a USB flash drive is connected directly to the
projector’s USB port.
If a USB memory card reader having multiple memory slots is connected, the drive
(memory slot) list is displayed in the file list.
Select the drive in which the memory card is inserted with [ ] / [ ], and press the
OK button.
•Active drives are displayed in white text, while inactive drives are grayed out.
■Selecting a Folder
In list view, folders that contain images can be selected.
•To return to the higher level, select [ ].
■Selecting an Image File for Projection
When you select an image file, a small preview of the image is shown in the
preview area.
For full-screen projection of the image, press the OK button.
To return to the higher level, select [ ].
■Changing the View
To switch the view, select [Thumbnail view] or [List view] in the drive or file list and
press the OK button.
Operating the Projected Image
When images are projected, you can perform the following operations.
Project the previous or next image by pressing the [ ] / [ ] buttons.
Rotate images left or right 90° by pressing the [ ] / [ ] buttons.
Return to the USB file browser by pressing the OK button.
•These operations are also available during slideshows. (Except during
transitions.)
•If the image contains rotational information, the image is rotated to an appropriate
direction automatically.
161
Advanced Projection
Advanced Guide Advanced Projection
Running a Slideshow of Data Saved in a USB
Flash Memory
Multiple images on a USB flash drive can be projected consecutively, with each
shown for a specific interval.
■Creating an Image File Folder
During slideshows, files in a folder are projected in alphabetical order by file name.
Keep this in mind when preparing the files in a folder on the USB flash drive.
■Setting a Slideshow Interval
Set the projection interval in [Slideshow interval] (P95) in the menu.
Split-Screen Display
Two input images can be projected side by side. This is split-screen display. When
you activate split-screen display, the current image is shown on the left side, and
the new image is shown at right. You can change the source of images shown on
each side by pressing the INPUT button. However, you cannot specify the same
input signal (terminal) as the source for both sides.
1Supply two signals to the projector.
2Press the MENU button on the remote control to select the [Input
settings] tab.
3Select [Split screen] and set it to [On].
4If or is displayed in the center of the image area, you can switch
control to the other side.
Network and USB input cannot be combined for split-screen display. Similarly, HDBaseT
and HDMI input, Analog PC-2 and Component input, or Digital PC and Analog PC-1 input
cannot be combined.
• A number is displayed in the center of the screen. The screen at left is labeled “1,” and
the screen at right, “2.” The image labeled with a number has “control rights,” and the
sound for that image will be played.
• For split-screen image adjustment, use the [Image priority] setting (P103).
• Some functions are not available, such as [Image flip H/V] (P105), [Screen aspect]
(P105), [Keystone] (P106), [Digital image shift] (P107), [Professional settings] (P107)
and [Logo capture] (P117).
• Image mode colors differ somewhat from those in single-image mode.
Advanced Projection
162
5Press the INPUT button, and then select the input signal for the side with
control rights.
Projecting from Multiple Projectors at Once
(Edge Blending)
Overlapping edges of images from multiple projectors used together can be
blended to make the overall image more seamless.
■Basic Instructions
Follow these steps when using two projectors side by side.
1In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust].
• If you specify [LAN] or [USB] as an input signal, the screen width is evenly divided
between the left and right areas. (P93)
• When projection resumes from standby or after the lamp is momentarily turned off in
split-screen mode, display reverts to single-image mode, showing the input signal with
display rights.
• If you have already completed edge blending settings, selecting [Adjust] will apply
them.
• To restore the default settings before adjustment, select [Reset].
Side currently under control
(input signal can be
switched)
Orange display
Current input signal of side
without control rights
White display
Current input signal of
side with control rights
Green display
163
Advanced Projection
Advanced Guide Advanced Projection
2Set [Marker] to [On].
Marker lines are projected on the images. The red marker indicates the start
position for adjustment, and the green marker, the end position.
3Adjust [Start position] for the side where images overlap. Move the start
marker to the outer edge of the overlapping area.
4Adjust [Width]. Move the end marker to the inner edge of the overlapping
area.
The area between the starting and ending markers is called the blending area.
Shading is applied to this area, and the brightness is adjusted to match
portions that overlap with other areas. After you complete settings for one
image, do the same thing for the other one to specify the blending area. Adjust
the settings to make the blending area for each image the same.
5Set [Marker] to [Off].
■Color Adjustment
In overlapping projection, portions of images in the overlapping area that pick up
other colors or are miscolored may be more noticeable. You can make this
overlapping area appear less distracting by performing Color blending adjustment.
1In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Color blending adjustment] > [Adjust].
2As you watch the image, adjust the value to eliminate unwanted colors in
the overlapping area.
First adjust red, green, and blue together by changing the [White] value, and
then adjust [Red], [Green], and [Blue] values individually.
3Repeat this adjustment on all projectors.
By default, the green and red markers are displayed in the same position, so only the red
marker is visible.
Advanced Projection
164
■Black Level Adjustment
In overlapping projection, dark colors are projected with less intensity than other
colors in the overlapping area. You can make this overlapping area less distracting
by adjusting the black level of non-overlapping image areas.
Here, the non-overlapping image area (from the end marker toward the center of
the image) is called area “D.”
Normally, three areas are identified in the context of end markers: A, B, and C.
In the following instructions, only area D is adjusted, and the widths of A, B, and C
are left at the default value of 0.
1In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Black level adjustment] > [Adjust].
2Select [Adjustment type] > [Black level].
3After selecting [D-area base], as you watch the image, adjust the values
so that the brightness and colors of the blending area and area D match.
Adjust [D-area base] to lighten the black level, and adjust [Red], [Green], and
[Blue] to obtain an optimal black level color tone, as needed.
4Repeat this adjustment on all projectors.
To prepare for adjustment, set [No signal screen] to [Black], start projection with no input
signal, and turn off the room lights, so that you can check dark image areas. (P117)
Area where dark colors look lighter
Left image Right image
Position of end marker (hidden)
D-area Blending area
165
Advanced Projection
Advanced Guide Advanced Projection
■Smoother Overlapping Areas
The black level along the right edge of area D (along the blending area) may be
more noticeable than that of surrounding areas.
By adjusting the black level of area B, you can make the transition smoother.
To compensate, adjust each area as follows.
When the projected image has multiple blending areas (on the top, bottom, and
each side), the width of areas A, B, and C must be adjusted to suit these blending
areas.
In this example, instructions are given for adjusting area B.
1In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Black level adjustment] > [Adjust].
2Select [Adjustment type] > [Area] > [Side] > [Right].
3Select [B-width], and then specify the width of area B.
Adjust the width of area B to roughly match the area where the black level is
noticeable.
This will make the width of area D narrower.
4Shading is applied to this area, and the brightness is adjusted to match
portions that overlap with other areas.
5As you watch the image, adjust the width of areas A, B, and C.
Results of adjusting the black level of area B are applied to all sides.
CBA
Area A: Black level cannot be adjusted.
Area B: Adjust to a black level different from that of area
D.
Area C: Adjust to provide a smooth transition relative to
the black levels of areas B and D.
Left image Position of end marker (hidden)
D-area Blending area
Areas C–A (default: 0)
Advanced Projection
166
6Readjust the black level of area B, as needed.
• To reduce distracting colors and colors that are out of alignment in areas where the images
overlap, perform [Color blending adjustment] targeting the main tone in the envisaged
projected image.
■Corner Adjustment
Projected images from multiple projectors used in overlapping projection must be
precisely repositioned. Positions of each corner in the blending area can be aligned
with the blending area of the reference projector.
1On the reference projector, configure keystone (P106) and edge-blending
(P109) settings, and then set the edge-blending markers to [On] (P163).
2In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Corner adjustment].
3Select a point to adjust, and move it so that the image as a whole looks
symmetrical.
• If you perform adjustments using [Color blending adjustment] or other menus, that may
not eliminate the distracting colors and differences in brightness in areas where the
images overlap.
• Blending can be fine-tuned by adjusting [Adjustment type] > [Black level] > [Red],
[Green], and [Blue].
• First, complete [Side] adjustment as described in “Basic Instructions” (P162).
• Sides set to an edge-blending width of 12 or more can be adjusted when [Keystone] is
set to [Corner adjustment] and the aspect ratio is [16:10].
• To reset adjustment, use [Keystone] (P106).
• A small edge-blending width may limit the amount of adjustment available.
167
Advanced Projection
Advanced Guide Advanced Projection
4As you watch the projected images, fine-tune markers of the projector
you are adjusting so that they overlap the reference projector markers as
much as possible.
5Set the reference projector’s edge-blending markers to [Off] (P163).
Adjust positions of each of the four corners in
the overlapping area. Correcting the position of
one point will also move the point on the
opposite side of the overlapping area, so that
the screen as a whole is corrected.
Image from reference
projector
Image from the projector adjusted
168
169
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Connection Procedure
Projection Procedure
Convenient Features
Advanced Guide
Using Menus
Menu Configuration
Menu Description
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
Other Information
170
Maintenance
Cleaning the Projector and the Air Filter
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Wipe the projector’s main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of
detergent in it, squeeze the cloth thoroughly, and then wipe the projector with it.
After cleaning, wipe the projector with a dry cloth.
Request Internal Cleaning Regularly
Dust that accumulates over long periods without cleaning may eventually cause fire
or electric shock. Once a year, request internal cleaning from the Canon Customer
Support Center. (Note that a fee is charged.) Cleaning before damp, rainy seasons
is especially effective.
Before cleaning the projector, always turn it off, unplug it after the
cooling fan stops, and wait at least one hour. Otherwise, you may get
burned because the main unit is very hot immediately after the
projector is turned off.
• Never use volatile cleaning liquid or benzine, as
these may damage the finish of the projector.
• When using a chemical dust cloth, make sure to
read the instructions thoroughly.
• When cleaning the projector’s lens, use a
commonly available air blower or lens cleaning
paper. The lens surface is easily damaged, so do
not use a hard cloth or tissues.
171
Maintenance
Other Information Maintenance
Cleaning the Air Filter
The air filter protects the lens and mirror inside the projector from dust and dirt.
Should the air filter become clogged with dust, the projector may be damaged since
it will block the air flow into the projector and raise the internal temperature of the
projector. The following screen is displayed when turning on the projector if the air
filter needs to be cleaned. Clean the air filter if it is displayed.
•Turn the power of the projector off and pull out the power plug.
•Hook your finger around the air filter handle on the front of the projector and
remove the air filter. Use a vacuum cleaner to clean off the dust.
•If the air filter cleaning screen is displayed when turning on the projector after
cleaning the air filter, select [Yes] and press the OK button.
The air filter counter is
reset, and the message is no longer displayed.
•This screen is not displayed when [Air filter warning display] is set to [Off]. (P115)
Reset the air filter counter manually. (P126)
• Only the [ ], [ ], OK and POWER buttons are
available while this screen is displayed. (When you
press the POWER button, the “Push POWER button
again to turn off power.” message appears.)
• When this screen has disappeared after being
displayed for 10 seconds, all buttons become operable.
Do not rinse the air filter in water. This may damage the air filter and projector.
Maintenance
172
Replacing the Air Filter
Follow the procedure below when replacing the air filter.
1Turn off the projector power and remove the power plug.
2Hook your finger around the air
filter frame handle on the side of
the projector, and pull the air
filter out to remove it.
3Remove the filter from the air
filter frame. First disengage the
tab on the inside, then remove
the entire air filter from the
frame.
4Install a new air filter into the
frame. First insert the air filter
tab into the groove on the handle
side of the frame, then press the
air filter into the frame.
5Securely insert the frame
holding the air filter, all the way
into the projector.
• Handle the air filter carefully. If damaged, the air filter will not work properly.
• When the lamp is replaced, it is recommended that you also replace the air filter.
• Replacement lamp part no.: RS-LP11
• Contact the Canon Customer Support Center for further information.
• Replacement air filter part no.: RS-FL01
Air filter
Air filter frame
handle
Air filter
Air filter frame
173
Maintenance
Other Information Maintenance
Replacing the Lamp
When the usage time of the lamp exceeds a certain amount of time, the following
message (two types) is displayed for 10 seconds every time the projector is turned
on.
2,700 hours to less than 3,000 hours
Prepare a new lamp when this screen is displayed.
•Only the [ ], [ ], OK, POWER, FOCUS, ZOOM and LENS SHIFT buttons are
available while this screen is displayed.
•When you press the POWER button, “Push POWER button again to turn off
power.” message appears.
•After this screen has been displayed for 10 seconds and disappeared, all buttons
become operable.
•This message will not be displayed again if you select [No] in response to the
message “Do you want to display this message again?”.
3,000 hours or more
If a lamp replacement message is displayed, refer to “Lamp Replacement
Procedure” (P176).
•Only the POWER, OK, FOCUS, ZOOM and LENS SHIFT buttons are available
while this screen is displayed.
•When you press the POWER button, the “Push POWER button again to turn off
power.” message appears.
•When this screen has disappeared after being displayed for 10 seconds, all
buttons become operable.
•You can check the usage time of the lamp in [Lamp counter] in the [System
settings] menu. (P125)
•This screen is not displayed when [Lamp warning display] is set to [Off]. (P115)
Maintenance
174
• Lamps are more likely to rupture once the lamp replacement
message has been displayed. Replace the lamp with a new one as
soon as possible.
• Lamps should be replaced about every 3,000 hours. Note that there
is no guarantee about how long lamps will last.
• Useful life of lamps varies widely from lamp to lamp and depending
on the environment of use. Some lamps may fail or rupture soon
after they are first used.
• Dispose of used lamps in accordance with local regulations.
175
Maintenance
Other Information Maintenance
Replacement Lamp
This projector uses the following lamps.
Lamp part no.: RS-LP11
Contact the Canon Customer Support Center when purchasing a replacement
lamp.
Precautions when replacing lamps that stop working
If the illumination suddenly stops when the projector is in use or after
you turn it on, the lamp may be broken. In this case, never attempt to
replace the lamp by yourself. Always request service from the
qualified technician or Canon Customer Support Center. Additionally,
with ceiling-mounted projectors, the lamp may fall out when you open
the lamp cover or while you are attempting to replace it. During
replacement, stand to the side of the lamp cover, not directly under it.
If the lamp breaks and any glass shards or other pieces get in your
eyes or mouth, consult a doctor immediately.
Before replacing the lamp, always turn off the projector, unplug it after
the cooling fan stops, and wait at least one hour. Do not touch the
lamp immediately after turning the projector off. It is very hot initially
and poses a risk of burns.
• Be sure to use the specified lamp.
• Contact the Canon Customer Support Center for further information.
This can also be purchased from the Canon website.
• Do not touch the inner glass surface when you replace the lamp.
Doing so may cause deterioration to the projector’s performance.
• Handle lamps with care. Impact or abrasion may cause lamps to
rupture while they are in use. If a lamp ruptures, contact the Canon
Customer Support Center and follow the instructions in “Note the
following precautions when replacing lamps that stop working.
Failure to do so could result in personal injury.” (P18).
• When replacing the lamp, do not remove any screws other than
those specified.
Maintenance
176
Lamp Replacement Procedure
1Turn off the projector power and remove the power plug.
2Loosen one screw and open the lamp cover in the direction of the arrow.
The lamp cover screw is attached to the lamp cover and designed to prevent it
from falling off.
3Loosen the 3 screws on the inside of the lamp unit, then slowly pull out
the lamp unit in the direction of the arrow.
Even when the screws are loosened, they will not fall off the lamp unit.
4Fully insert a new lamp unit and secure it with the 3 screws.
5Close the lamp cover and tighten the screws.
6Turn on the power. Bring up the menu and select [System settings] >
[Other settings] > [Lamp counter].
Screw
Maintenance
178
Installing / Removing the Lens Unit
■Installing the Lens Unit
1Use a Phillips-head screwdriver and loosen the lamp cover screw, then
open the lamp cover.
The lamp cover screw is attached to the lamp cover and designed to prevent it
from falling off.
• Before installing or removing the lens unit, be sure to disconnect the
power plug or connector. Failure to do so may result in fire, electric
shock, or injury.
• When hanging the projector from a ceiling, put the projector down
on the floor or a workbench before attaching or replacing the lens
unit. Failure to do so could result in parts falling off the projector and
may cause an accident or personal injury.
• Do not touch the lens when the lens is moving (the lens is shifting) to
adjust the projected image after installation. There is the risk of
injury.
• Before replacing the lens unit, make sure to turn off the projector,
wait at least 1 hour to allow the projector to cool thoroughly. Failure
to do so may result in burns or other injuries.
• Do not attempt to install or remove the lens unit yourself. Be sure to
request this service from a qualified technician or contact the Canon
Customer Support Center.
• When installing and removing the lens unit, be sure not to touch the
surface of the lens with your hands or scratch it.
• Do not apply force to parts (e.g. lead wires) that are connected to the
lens unit or lens motor. Doing so may cause a malfunction.
• Do not replace the lens unit in a dusty location. If any dust or dirt
enters the projector, this may adversely affect picture quality.
• When carrying or holding up the projector after attaching the lens
unit, be sure not to hold the lens. Doing so may cause damage to the
lens unit.
• If transportation is necessary, the lens unit should be removed
before transporting the projector. If the projector is subjected to
excessive impacts during transportation, the lens unit may be
damaged.
• For details about which devices the projector is compatible with,
contact the Canon Customer Support Center.
Screw
179
Maintenance
Other Information Maintenance
2Loosen the cosmetic panel screw, then slide the cosmetic panel toward
the rear to remove it.
The cosmetic panel screw is attached to the cosmetic panel and designed to
prevent it from falling off.
3In order to prevent damage, close the lamp cover and temporarily fasten
the screw.
4Remove the sleeve screws (2 on top and 2 on bottom).
After the 2 screws on top are removed, turn the projector upside down on a flat
desk or similar location and remove the 2 screws from the bottom.
Maintenance
180
5Then turn the projector back over and remove the sleeve.
6Referring to the following illustration, insert the lens connector of the
lens unit into the front right side of the projector slowly until it contacts
the end. At this time, pull out the lens cable shown in the illustration and
fix it.
7Tighten the 4 screws to fasten the lens unit in place.
The 4 lens unit screws are attached to the lens unit and cannot be removed.
Lens connector
Lens cable
181
Maintenance
Other Information Maintenance
8Insert the projector lens cable into the connector until a click sound is
heard.
9Reinstall the sleeve, cosmetic panel, and lamp cover in their original
positions.
When the power is first turned on after the lens unit has been installed or replaced, lens
shift initialization operation will be performed. It will take approximately 1 minute for the
initialization operation to start up. However, if the lens has been replaced with a lens of
the same model number, initialization operation will not be performed. The position will be
the same as before the lens was replaced.
The lens shift initialization operation uses the motor to move the lens
up / down / left / right. Do not touch the lens. Doing so could result in
an injury.
When installing and removing the lens unit, be sure to fix the lens
cable as shown in the illustration. When inserting the lens unit, it is
possible to damage the lens cable between the lens unit and projector.
Maintenance
182
■Removing the Lens Unit
1Perform steps 1 to 5 of “Installing the Lens Unit” (P178 – P180) to remove
the sleeve.
2Disconnect the lens cable from the lens connector.
3Fix the lens cable as shown in the illustration and loosen the 4 screws to
remove the lens unit.
The 4 lens unit screws are attached to the lens unit and cannot be removed.
When pulling out (disconnecting) the lens cable, press the buttons on both sides of the
lens cable connector while pulling out the cable.
183
Other Information Product Specifications
Product Specifications
Relationship between Aspect and Screen
Aspect
This section describes the relationship between screen aspect (P63) and aspect
(P65).
Select an optimum aspect ratio of the projected image (screen aspect) or an
optimum screen mode (aspect) according to the aspect ratio of the screen, type of
input image signal and so on for the projection to make best use of the screen size.
•If a computer image with an aspect ratio of 16:9 is not projected correctly when
the setting is [Auto], select [16:9] as the screen aspect.
•For a 16:9 image with black borders at the top and bottom, such as a terrestrial
broadcast movie, you can project the 16:9 image area so that it is projected on
the entire screen by selecting [Zoom] in [Aspect].
There may be some cases that [Zoom] cannot be selected depending on the
input signal and/or resolution.
•For keystone correction (P67), select an option other than [4:3 D. image shift] or
[16:9 D. image shift] for Screen aspect.
■When projecting at the original aspect ratio on a 16:10
screen
Original Aspect
Ratio
Screen aspect
setting (P63)Aspect setting (P65) Screen image
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[16:10]
[16:10]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[16:9]
[Auto]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
Product Specifications
184
■When projecting at the original aspect ratio on a 16:9
screen
■When projecting at the original aspect ratio on a 4:3
screen
Original Aspect
Ratio
Screen aspect
setting (P63)Aspect setting (P65) Screen image
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[16:9]
[16:9
D. image shift]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[16:9]
[Auto]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
Original Aspect
Ratio
Screen aspect
setting (P63)Aspect setting (P65) Screen image
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[4:3]
[4:3
D. image shift]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[16:9]
[Auto]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[4:3]
[Auto]
185
Product Specifications
Other Information Product Specifications
■When projecting to fill a 16:10 screen
■When projecting to fill a 16:9 screen
Original Aspect
Ratio
Screen aspect
setting (P63)Aspect setting (P65) Screen image
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[16:10]
[16:10]
[Auto]
(16:9)
1920 x 1080
1280 x 720
[16:10]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[16:10]
Original Aspect
Ratio
Screen aspect
setting (P63)Aspect setting (P65) Screen image
(16:10)
1920 x 1200
1440 x 900
1280 x 800
[16:9]
[16:9
D. image shift]
[16:9]
(16:9)
1920 x 1080
1280 x 720
[16:9]
[Auto]
(4:3)
1600 x 1200
1400 x 1050
640 x 480
[16:9]
187
Product Specifications
Other Information Product Specifications
Displayed Test Patterns
To access the test pattern menu, from the [Install settings] menu, select [Test
pattern] > [On] (P115).
While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch
patterns. Also, if there is an option pattern available, you can use the [ ] / [ ]
buttons to switch pattern. A dialog box is shown during test pattern display that
identifies the current test pattern and provides operating instructions.
The following test patterns can be displayed.
Use [ ] / [ ] to
switch patterns
Use [ ] / [ ] to switch
option patterns
Raster 100%
(White / red / green / blue)
Raster 50%
(White / red / green / blue)
Color bars
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
Stairstep H
Stairstep V
Cross Hatch
Border
Focus
Multi
Checker
Color steps
Character
Product Specifications
188
Supported Signal Types
This projector supports the following signal types.
If your computer or AV equipment is compatible with any one of these signal types,
the projector’s Auto PC function selects the input signal type to project an image
appropriately.
Analog PC
Digital PC
Resolution (dots) Signal type Horizontal frequency
(kHz) Vertical frequency (Hz)
640 x 480 VGA 31.469 59.940
720 x 480 – 31.469 59.940
720 x 576 – 31.250 50.000
800 x 600 SVGA 37.879 60.317
848 x 480 – 31.020 60.000
1024 x 768 XGA 48.363 60.004
1280 x 768
WXGA
47.776 59.870
47.396 59.995
1280 x 800 49.702 59.810
49.306 59.910
1280 x 960 – 60.000 60.000
1280 x 1024 SXGA 63.981 60.020
1366 x 768 – 47.712 59.790
1400 x 1050 SXGA+ 64.744 59.948
65.317 59.978
1440 x 900 WXGA+ 55.935 59.887
55.469 59.901
1600 x 900 – 60.000 60.000
1600 x 1200 UXGA 75.000 60.000
1680 x 1050 WSXGA+ 64.674 59.883
65.290 59.954
1920 x 1080 – 56.250 50.000
67.500 60.000
1920 x 1200 WUXGA 74.038 59.950
Resolution (dots) Signal type Horizontal frequency
(kHz) Vertical frequency (Hz)
640 x 480 D-VGA 31.469 59.940
720 x 480 – 31.469 59.940
720 x 576 – 31.250 50.000
800 x 600 D-SVGA 37.879 60.317
1024 x 768 D-XGA 48.363 60.004
1280 x 720 – 37.500 50.000
45.000 60.000
1280 x 800 D-WXGA 49.702 59.810
49.306 59.910
1280 x 1024 D-SXGA 63.981 60.020
1366 x 768 – 47.712 59.790
1400 x 1050 D-SXGA+ 64.744 59.948
65.317 59.978
1440 x 900 D-WXGA+ 55.935 59.887
55.469 59.901
1600 x 900 – 60.000 60.000
1600 x 1200 D-UXGA 75.000 60.000
1680 x 1050 D-WSXGA+ 64.674 59.883
65.290 59.954
1920 x 1080 –
27.000 24.000
56.250 50.000
67.500 60.000
189
Product Specifications
Other Information Product Specifications
HDMI/HDBaseT
Connecting to a computer
Connecting with AV equipment
Component
* The specifications in the table above are subject to change without notice.
* This projector does not support any computer output signal with a dot clock of higher than 162 MHz.
* Use a computer cable in which all pins are connected. If the cable is a type in which all pins are not
connected, the image may not be correctly displayed.
1080PsF
(1920 x 1080i) –
27.000 24.000
28.125 25.000
33.750 30.000
1920 x 1200 D-WUXGA 74.038 59.950
Resolution (dots) Signal type Horizontal frequency
(kHz) Vertical frequency (Hz)
640 x 480 VGA 31.469 59.940
800 x 600 SVGA 37.879 60.317
1024 x 768 XGA 48.363 60.004
1280 x 800 WXGA 49.702 59.810
49.306 59.910
1280 x 1024 SXGA 63.981 60.020
1366 x 768 – 47.712 59.790
1400 x 1050 SXGA+ 64.744 59.948
65.317 59.978
1440 x 900 WXGA+ 55.935 59.887
55.469 59.901
1600 x 900 – 60.000 60.000
1600 x 1200 UXGA 75.000 60.000
1680 x 1050 WSXGA+ 64.674 59.883
65.290 59.954
1920 x 1200 WUXGA 74.038 59.950
Signal type Horizontal frequency (kHz) Vertical frequency (Hz)
480p 31.469 59.940
576p 31.250 50.000
720p 37.500 50.000
45.000 60.000
1080i 28.125 50.000
33.750 60.000
1080p
27.000 24.000
56.250 50.000
67.500 60.000
Signal type Horizontal frequency (kHz) Vertical frequency (Hz)
480i 15.734 59.940
480p 31.469 59.940
576i 15.625 50.000
576p 31.250 50.000
720p 37.500 50.000
45.000 60.000
1080i 28.125 50.000
33.750 60.000
1080p 56.250 50.000
67.500 60.000
1080PsF
27.000 24.000
28.125 25.000
33.750 30.000
Resolution (dots) Signal type Horizontal frequency
(kHz) Vertical frequency (Hz)
Product Specifications
190
■Projector
Model name WUX6500
Display system Reflective liquid crystal panel (LCOS) : 3 panels
Optical system Color separation by dichroic mirror / polarizing beam splitter
and color composition by prism
Display device
Effective display area size 0.71'' / 16:10
Effective number of pixels 2,304,000 (1920 x 1200)
Other features Active matrix system
Projection lens
Zoom (*4) 1.5x (Electric)
Focus Electric
Lens shift (*4) V: -15% to +55% (Electric), H: ±10% (Electric)
Focal length (*4) f = 23.0 to 34.5 mm (0.9'' - 1.4'')
F value (*4) F1.89 to F2.65
Light source High pressure mercury lamp 370 W
Image size / Projection
distance (*4)
Minimum: 101.6 cm (40'') to Maximum: 1524 cm (600''),
Projection distance: 1.3 m to 29.0 m (4.3'- 95.1')
Number of colors 16,770,000 colors
Brightness (*1) (*2) 6,500 lumen
Contrast ratio (*1) (*3) 2000:1 (Fully white : fully black, native)
Ratio of brightness at
periphery to center (*1) (*4) 88%
Speaker 5W monaural
Supported input signal types Refer to “Supported Signal Types” (P188 - P189)
Display resolution
Computer signal input Maximum input resolution 1920 x 1200 dots
Video signal input Maximum input resolution 1920 x 1200 dots
Video signals
Analog PC input WUXGA / UXGA / WSXGA+ / SXGA+ / WXGA+ / FWXGA /
WXGA / SXGA / XGA / SVGA / VGA
Digital PC input WUXGA / UXGA / WSXGA+ / SXGA+ / WXGA+ / FWXGA /
WXGA / SXGA / XGA / SVGA / VGA
Digital video input 1080p / 1080i / 720p / 576p / 480p
Component video input 1080p / 1080i / 720p / 576p / 576i / 480p / 480i
Video signal input terminal
Mini D-sub 15-pin Analog PC, Component
DVI-I Analog PC, Digital PC (29-pin DVI connector)
HDMI Digital PC, Digital Video
RJ-45 (HDBaseT) HDBaseT input (video / audio / control / network)
191
Product Specifications
Other Information Product Specifications
*1Compliance with ISO21118-2012
*2When using a Standard Zoom Lens (RS-IL01ST) in [Presentation] image mode and [Full power]
lamp mode.
*3When using a Standard Zoom Lens (RS-IL01ST) in [Presentation] image mode and setting the
lamp control to [On].
*4When using a Standard Zoom Lens (RS-IL01ST).
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels
may stay lit or unlit due to the characteristics of the LCD panel.
* Using the projector continuously for an extended period of time may accelerate the deterioration of
optical parts.
* Product specifications and appearance are subject to change without prior notice.
Other terminals and connectors
Mini jack x 2 AUDIO IN
Mini jack AUDIO OUT
Mini jack Wired remote control
RS-232C CONTROL (Dsub9)
USB USB Type A
RJ-45 Network connections (1000BASE-T/100BASE-TX/10BASE-T)
Noise 43dB / 39dB (lamp mode: Full power / Power saver)
Operating temperature 0°C (32°F) to 40°C (104°F)
Power supply AC100V to 240V 50 / 60Hz
Full power 500W
Power consumption in standby mode
Networking and HDBaseT
off 0.3W
Low-power networking on,
HDBaseT off 0.7W
Networking off, HDBaseT
on 1.9W
Low-power networking and
HDBaseT on 2.0W
Standard dimensions 380 mm (W) x 170 mm (H) x 430 mm (D) / 15.0 (W) x 6.7 (H) x
16.9 (D) in
Weight 8.5 kg / 18.7 lbs
Accessories
Remote control, remote control dry-cell batteries, power cord,
PC cable, Important Information, User’s Manual (CD-ROM)
and Warranty Card
Model name WUX6500
Product Specifications
192
■Remote Control
■Specification of Each Lens Unit (Option)
For details about the amount of lens shift, refer to “Lens Shift Function” on page 47.
Type RS-RC04 RS-RC05 (Option)
Power supply DC 3.0V, using two AAA-size
batteries DC 3.0V, using two AA-size batteries
Operating range Approx. 8 m± 25° horizontal and vertical (to infrared remote receiver)
Dimensions
43 mm (W) x 23 mm (H) x
135 mm (D) /
1.7 (W) x 0.9 (H) x 5.3 (D) in.
51 mm (W) x 28 mm (H) x
176 mm (D) /
2.0 (W) x 1.1 (H) x 6.9 (D) in.
Weight 56 g / 2.0 oz 100 g / 3.5 oz
Name Standard Zoom Lens Long Zoom Lens
Model number RS-IL01ST RS-IL02LZ
External View
Focal length 23.0 - 34.5 mm
(0.9 - 1.4'')
34.0 - 57.7 mm
(1.3 - 2.3'')
F number 1.89 - 2.65 1.99 - 2.83
Width 97.4 mm (3.8'') 97.4 mm (3.8'')
Height 106.5 mm (4.2'') 106.5 mm (4.2'')
Length 173.4 mm (6.8'') 173.4 mm (6.8'')
Weight 550 g (1.2 lbs) 755 g (1.7 lbs)
Zoom ratio 1.5x 1.7x
Projection
distance
1.3 - 29.0 m
(4.3 - 95.1')
1.9 - 48.5 m
(6.2 - 159.1')
Size 100
projection
distance
3.2 - 4.8 m
(10.5 - 15.7')
4.7 - 8.0 m
(15.4 - 26.2')
193
Product Specifications
Other Information Product Specifications
For details about the amount of lens shift, refer to “Lens Shift Function” on page 47.
Name Short Fixed Lens Ultra Long Zoom Lens
Model number RS-IL03WF RS-IL04UL
External View
Focal length 12.8 mm (0.5'') 53.6 - 105.6 mm (2.1 - 4.2'')
F number 2.0 2.34 - 2.81
Width 97.4 mm (3.8'') 97.4 mm (3.8'')
Height 106.5 mm (4.2'') 106.5 mm (4.2'')
Length 175.2 mm (6.9'') 184.2 mm (7.3'')
Weight 910 g (2.0 lbs) 940 g (2.1 lbs)
Zoom ratio – 1.95x
Projection
distance 0.7 - 5.2 m (2.3 - 17.1') 4.6 - 90.0 m (15.1 - 295.3')
Size 100
projection
distance
1.7 m (5.6') 7.7 - 15.0 m (25.3 - 49.2')
Name Wide Zoom Lens
Model number RS-IL05WZ
External View
Focal length 15.6 - 23.3 mm (6.0 - 9.0")
F number 2.09 - 2.34
Width 97.4 mm (3.8")
Height 106.5 mm (4.2")
Length 180.3 mm (7.1")
Weight 905 g (2.0 lbs)
Zoom ratio 1.5x
Projection
distance 0.9 - 19.5 m (3.0 - 64.0')
Size 100
projection
distance
2.2 - 3.2 m (7.2 - 10.5')
Product Specifications
194
■External View
53 mm (2.1'')
128 mm (5.0'')
212 mm (8.35'')
234.5 mm (9.2'')
92 mm (3.6'')
91 mm (3.6'')
150 mm (5.9'')
311 mm (12.2'')
154.5 mm (6.1'')
141.5 mm (5.6'')
170 mm (6.7'')
430 mm (16.9'')
380 mm (15.0'')
WUX6500
Bolt holes (M4 x 6) for
installation of ceiling
attachment
195
Product Specifications
Other Information Product Specifications
■ANALOG PC-2 / COMPONENT Terminal
This terminal is used as a computer ANALOG PC input or COMPONENT input
terminal. Use a D-sub computer cable.
The terminal specifications for the ANALOG PC input and COMPONENT input are
the same.
Mini D-sub 15-pin
■Service Port (CONTROL)
Pin assignment
Communication format
Communication mode : RS-232C, asynchronous, half-duplex communication
Communication speed : 19200bps
Character length : 8 bits
Stop bits : Switchable between 1 bit and 2 bits. Factory default, or
state after [Factory defaults] is executed, is 1 bit.
Parity : None
Flow control : None
The service port is not available when [HDBaseT] is set to [On] and [Serial
communication] is set to [HDBaseT].
Pin No. Signal Pin No. Signal
1 R 9 +5 V power
2G 10
Ground
(Vertical sync.)
3 B 11 Ground
4OPEN 12DDC data
5Ground
(Horizontal sync.) 13 Horizontal sync.
6 Ground (R) 14 Vertical sync.
7 Ground (G) 15 DDC clock
8 Ground (B)
Pin No. Signal
1OPEN
2RxD
3TxD
4OPEN
5GND
6OPEN
7 Internal pull-up
8OPEN
9OPEN
Product Specifications
196
User commands
Commands ASCII representation Binary representation
Power supply
Power on POWER=ON<CR> 50h 4Fh 57h 45h 52h 3Dh 4Fh 4Eh 0Dh
Power off POWER=OFF<CR> 50h 4Fh 57h 45h 52h 3Dh 4Fh 46h 46h
0Dh
Power status
acquisition GET=POWER<CR> 47h 45h 54h 3Dh 50h 4Fh 57h 45h 52h
0Dh
Input source
HDMI INPUT=HDMI<CR> 49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh
49h 0Dh
Digital PC INPUT=D-RGB<CR> 49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 0Dh
Analog PC-1 INPUT=A-RGB1<CR> 49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h
47h 42h 31h 0Dh
Analog PC-2 INPUT=A-RGB2<CR> 49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h
47h 42h 32h 0Dh
Component INPUT=COMP<CR> 49h 4Eh 50h 55h 54h 3Dh 43h 4Fh 4Dh
50h 0Dh
LAN INPUT=LAN<CR> 49h 4Eh 50h 55h 54h 3Dh 4Ch 41h 4Eh
0Dh
USB INPUT=USB<CR> 49h 4Eh 50h 55h 54h 3Dh 55h 53h 42h
0Dh
HDBaseT INPUT=HDBT<CR> 49h 4Eh 50h 55h 54h 3Dh 48h 44h 42h
54h 0Dh
Input source
acquisition GET=INPUT<CR> 47h 45h 54h 3Dh 49h 4Eh 50h 55h 54h
0Dh
Image Mode
Standard IMAGE=STANDARD<CR> 49h 4Dh 41h 47h 45h 3Dh 53h 54h 41h
4Eh 44h 41h 52h 44h 0Dh
Presentation IMAGE=PRESENTATION<CR>
49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h
53h 45h 4Eh 54h 41h 54h 49h 4Fh 4Eh
0Dh
VividPhoto IMAGE=VIVID_PHOTO<CR> 49h 4Dh 41h 47h 45h 3Dh 56h 49h 56h
49h 44h 5Fh 50h 48h 4Fh 54h 4Fh 0Dh
Photo/sRGB IMAGE=PHOTO_SRGB<CR> 49h 4Dh 41h 47h 45h 3Dh 50h 48h 4Fh
54h 4Fh 5Fh 53h 52h 47h 42h 0Dh
Dynamic IMAGE=DYNAMIC<CR> 49h 4Dh 41h 47h 45h 3Dh 44h 59h 4Eh
41h 4Dh 49h 43h 0Dh
Video IMAGE=VIDEO<CR> 49h 4Dh 41h 47h 45h 3Dh 56h 49h 44h
45h 4Fh 0Dh
Cinema IMAGE=CINEMA<CR> 49h 4Dh 41h 47h 45h 3Dh 43h 49h 4Eh
45h 4Dh 41h 0Dh
User 1 IMAGE=USER_1<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 31h 0Dh
User 2 IMAGE=USER_2<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 32h 0Dh
User 3 IMAGE=USER_3<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 33h 0Dh
User 4 IMAGE=USER_4<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 34h 0Dh
User 5 IMAGE=USER_5<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 35h 0Dh
Image mode
acquisition GET=IMAGE<CR> 47h 45h 54h 3Dh 49h 4Dh 41h 47h 45h
0Dh
197
Product Specifications
Other Information Product Specifications
Brightness Brightness
value setting BRI=<value><CR> 42h 52h 49h 3Dh <numeric code> 0Dh
Brightness
acquisition GET=BRI<CR> 47h 45h 54h 3Dh 42h 52h 49h 0Dh
Sharpness Sharpness
value setting SHARP=<value><CR> 53h 48h 41h 52h 50h 3Dh <numeric
code> 0Dh
Sharpness
acquisition GET=SHARP<CR> 47h 45h 54h 3Dh 53h 48h 41h 52h 50h
0Dh
Contrast Contrast value
setting CONT=<value><CR> 43h 4Fh 4Eh 54h 3Dh <numeric code>
0Dh
Contrast
acquisition GET=CONT<CR> 47h 45h 54h 3Dh 43h 4Fh 4Eh 54h 0Dh
Aspect
Auto ASPECT=AUTO<CR> 41h 53h 50h 45h 43h 54h 3Dh 41h 55h
54h 4Fh 0Dh
4:3 ASPECT=4:3<CR> 41h 53h 50h 45h 43h 54h 3Dh 34h 3Ah
33h 0Dh
16:9 ASPECT=16:9<CR> 41h 53h 50h 45h 43h 54h 3Dh 31h 36h
3Ah 39h 0Dh
16:10 ASPECT=16:10<CR> 41h 53h 50h 45h 43h 54h 3Dh 31h 36h
3Ah 31h 30h 0Dh
Zoom ASPECT=ZOOM<CR> 41h 53h 50h 45h 43h 54h 3Dh 5Ah 4Fh
4Fh 4Dh 0Dh
True size ASPECT=TRUE<CR> 41h 53h 50h 45h 43h 54h 3Dh 54h 52h
55h 45h 0Dh
Aspect value
acquisition GET=ASPECT<CR> 47h 45h 54h 3Dh 41h 53h 50h 45h 43h
54h 0Dh
Lamp mode Full power LAMP=FULL<CR> 4Ch 41h 4Dh 50h 3Dh 46h 55h 4Ch 4Ch
0Dh
Power saver LAMP=ECO<CR> 4Ch 41h 4Dh 50h 3Dh 45h 43h 4Fh 0Dh
Lamp mode
value
acquisition
GET=LAMP<CR> 47h 45h 54h 3Dh 4Ch 41h 4Dh 50h 0Dh
Blank
Blank On BLANK=ON<CR> 42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 4Eh 0Dh
Blank Off BLANK=OFF<CR> 42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 46h 46h
0Dh
Blank
acquisition GET=BLANK<CR> 47h 45h 54h 3Dh 42h 4Ch 41h 4Eh 4Bh
0Dh
Commands ASCII representation Binary representation
198
Troubleshooting
LED Indicator Details
When there is a problem with the projector, the LED indicator on the side of the
projector illuminates or flashes continuously after the projector is turned off.
• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet before
dealing with the problem.
LED indicator
status Meaning Cause and countermeasure
WARNING and
TEMP are lit.
Temperature
abnormality
The temperature inside the projector is too high for
some reason or the outside air temperature is
higher than the operating range. If the problem is
inside the projector, check whether the projector is
installed and operating normally, unplug the
projector from the power outlet to cool down the
projector interior and then restart projection. If the
air intake or exhaust vent is blocked, remove the
obstacle. If the air filter is clogged, clean or replace
it. (P171, P172) If the same warning occurs again,
there may be a malfunction in the projector.
Contact the Canon Customer Support Center.
WARNING and
LAMP are lit.
Faulty lamp The lamp does not illuminate. If the lamp does
not illuminate, replace it. (P173) If the same
warning occurs again, there may be a
malfunction in the lamp drive circuit. Contact the
Canon Customer Support Center.
WARNING
flashes 3 times,
LAMP is lit.
Faulty lamp
cover
The lamp cover is open. Unplug the projector
from the power outlet, then install the lamp cover
correctly and turn on the projector again.
If the lamp cover has been installed properly,
there may be a malfunction in the lamp cover
detection switch. Contact the Canon Customer
Support Center.
WARNING
(only) flashes 4
times
repeatedly.
Faulty
cooling fan
There may be a malfunction in the cooling fan or
another component. Unplug the projector from
the electrical outlet, then plug it back into the
outlet and turn on the projector again. Contact
the Canon Customer Support Center if the same
warning occurs again.
WARNING
(only) flashes 5
times
repeatedly.
Faulty power
supply
Abnormal voltage is applied to some parts in the
power supply or another failure may have
occurred. Unplug the projector from the electrical
outlet, then plug it back into the outlet and turn on
the projector again. Contact the Canon Customer
Support Center if the same warning occurs
again.
199
Troubleshooting
Other Information Troubleshooting
Symptoms and Solutions
■You Cannot Turn on the Projector
WARNING
(only) flashes 3
times
repeatedly.
Filter error The air filter is not installed. Check whether or not
the air filter is installed correctly. Contact the
Canon Customer Support Center if the same
warning occurs again.
WARNING
(only) flashes 6
times
repeatedly.
Faulty lens
connector
The lens cable is not connected to the lens unit
correctly. Unplug the projector, connect the lens
cable to the lens unit correctly, and then plug the
projector in again. Contact the Canon Customer
Support Center if the same warning occurs
again.
Cause Countermeasure
The power cord is not
connected correctly.
Check whether the power cord is connected
correctly. (P52)
The power cord has just
been connected.
Wait at least one second after plugging the projector
in until you press the POWER button. You cannot
turn the projector on immediately after plugging it in.
(P53)
The lamp cover is open. Unplug the projector from the power outlet, then
install the lamp cover correctly and turn on the
projector again.
The safety device is
activated because the air
intake or the exhaust
vent is blocked and the
internal temperature of
the projector has
increased.
When the safety device is active, the [POWER ON]
indicator does not turn on when you connect the
power cord. You cannot disable this safety device.
Remove any obstacle that is blocking the air intake or
exhaust vent and contact the Canon Customer
Support Center.
The lens connector is
not attached correctly.
The lens cable is not connected to the lens unit
correctly. Unplug the projector, connect the lens
cable to the lens unit correctly, and then plug the
projector in again. Contact the Canon Customer
Support Center if the same warning occurs again.
The air filter is not
installed correctly.
Check whether the air filter is installed correctly.
(P172)
Key lock is enabled.
Check that Key lock (P118) is not enabled for the
projector or the remote control.
LED indicator
status Meaning Cause and countermeasure
Troubleshooting
200
■You Cannot Project an Image from the Projector
Cause Countermeasure
A cable is not connected
correctly.
Check whether the projector is connected to the
computer or AV equipment correctly. (P49 - P51)
20 seconds have not
elapsed since the
projector was turned on.
When the projector is turned on, the opening window
is displayed for approximately 20 seconds. To project
an image immediately, press the OK button on the
remote control or side control. (P30, P35)
No image is sent from
the AV equipment.
Check whether an image is played on the connected
video camcorder, DVD, etc.
Connection with the
input terminal has not
been performed
correctly.
Check whether the AV equipment is connected to the
projector input terminal correctly. (P33)
No input signal type has
been selected for the
connected AV
equipment.
Check that the same input signal has been correctly
selected for the connected AV equipment from the
[INPUT] menu. (P56)
The input signal type is
incorrect.
Check whether the selected input signal type is
correct. (P91, P188)
The BLANK function has
been selected.
Press the BLANK button on the remote control.
(P72)
No image is projected
due to a problem with
the computer.
Turn first the projector and then the computer off and
then back on again.
The external monitor
output is not set on the
notebook computer
correctly.
Turn on the external monitor output on the notebook
computer. To turn on the external monitor output,
press the [LCD] or [VGA] function key or a key with
an icon for the external monitor, while holding down
the [Fn] key on the keyboard of the notebook
computer. With Windows 10 / Windows 8.1 /
Windows 8 / Windows 7, you can turn on image
output by holding down the Windows logo key and
pressing the [P] key. (P55)
The combination of keys used to perform this
operation varies depending on the model of
notebook computer. For more detailed information,
refer to the manual that came with your computer.
The computer is set to
dual screen (multi-
display) mode.
If dual screen mode is selected, change the
computer display output to mirroring mode.
The output setting method varies among computer
manufacturers. For more detailed information, refer
to the manual that came with your computer.
201
Troubleshooting
Other Information Troubleshooting
■There is no Sound
■The Projected Image Is Blurred
The image files are not
compatible with USB File
Browser.
Projection from USB flash drives requires JPEG
images with a resolution not exceeding 10912x8640,
single-byte alphanumeric file names, and a FAT-
formatted drive.
The LAN cable (shielded
twisted pair) is not
connected correctly.
When [LAN] or [HDBaseT] is selected in the [Input]
menu, check whether the LAN cable (shielded
twisted pair) is connected to the projector correctly.
(P127)
[HDBaseT] was changed
from [On] to [Off] while
[Communication
settings] > [Wired
network] was set to
[HDBaseT].
Configure the [HDBaseT] setting again as follows.
(P120)
If [HDBaseT] is selected in the [Input] menu, change
the [HDBaseT] setting from [Off] to [On] again.
Cause Countermeasure
The audio cable is not
connected correctly.
Check the audio cable connection. (P49, P51)
The MUTE function is
enabled.
Press the MUTE button on the remote control. (P36)
The volume level is
adjusted to the
minimum.
Press the VOL button on the remote control or the
VOL+ button on the side control to adjust the volume
level. (P30, P36)
An audio cable with a
built-in resistor is used.
Use an audio cable without a built-in resistor.
Audio in terminal select
is [Off].
Change the Audio In terminal to the appropriate
setting. (P119)
Cause Countermeasure
The image is out of
focus.
Adjust the focus. (P59)
The distance to the
screen is too short.
Check whether the distance to the screen is
appropriate. (P43)
The projector is not
placed straight in front of
the screen.
Check whether the projector is placed obliquely to
the screen. A slight error in the projection angle can
be corrected through the keystone adjustment
function. (P67)
Cause Countermeasure
Troubleshooting
202
■You Cannot Project an Image Appropriately
■The Projector Power Turns Off
The projector has been
moved to a place where
the temperature varies a
lot.
When the projector is moved from a location where
the temperature is low to a location where the
temperature is high, condensation may form on the
lens. The condensation will evaporate after a period
of time and the projector will be able to project a
normal image.
The lens is stained. Clean the lens. (P170)
The tracking is bad. Adjust the tracking with the [Auto PC] (P91) or
[Tracking] (P92) function.
Video is blurred. Activate motion blur reduction. (P123)
Motion blur reduction is
not available.
Motion blur reduction is not available in projection
using USB flash drives or networked multi-projection.
The sharpness setting is
not available.
Sharpness cannot be adjusted during split-screen
display.
Cause Countermeasure
The projected image is
inverted in the vertical or
horizontal direction.
The ceiling mounted / rear projection setting is
incorrect. Check the [Image flip H/V] setting in the
[Install settings] menu. (P105)
The dot clock of the input
signal is higher than 162
MHz.
Set the signal dot clock to 162 MHz or less on your
computer.
A computer cable is
used in which some pins
are not connected.
Use a computer cable in which all pins are
connected.
Cause Countermeasure
The air intake or exhaust
vent is blocked.
Check whether the air intake or exhaust vent is
blocked. If the air intake or exhaust vent is blocked,
the temperature inside the projector will increase and
the power is automatically turned off to protect the
projector. (The [WARNING] indicator and [TEMP]
indicator are lit.) Wait until the projector temperature
drops, then make sure that the intake and exhaust
vents are not blocked and turn on the projector. (P29,
P53)
The air filter is dirty. Check whether the air filter is clogged with dust.
If the air filter is clogged, clean or replace the air filter.
(P171, P172)
Cause Countermeasure
203
Troubleshooting
Other Information Troubleshooting
■The Projector Cannot Join the Network
The lamp has ruptured
(or there is a lamp
malfunction).
If the lamp has ruptured, follow the instructions in
“Note the following precautions when replacing
lamps that stop working. Failure to do so could result
in personal injury.” (P18).
The operating
environment is
inappropriate.
Check whether the operating temperature is between
0°C (32°F) and 40°C (104°F). (P22)
Projector settings must be adjusted when using the
projector at altitudes of 2,300 m (7,545.8') or higher.
In the [Install settings] menu, set [Fan mode] under
[Professional settings] to [High altitude]. (P108)
Cause Countermeasure
The LAN cable (shielded
twisted pair) is not
connected correctly.
Check whether the LAN cable (shielded twisted pair)
is connected to the projector correctly. (P127)
[HDBaseT] was changed
from [On] to [Off] while
[Communication
settings] > [Wired
network] was set to
[HDBaseT].
Configure the [HDBaseT] setting again as follows.
(P120)
1. Change the [HDBaseT] setting from [Off] to [On]
again.
2. Change the wired network setting from [LAN port]
to [HDBaseT].
3. Following the instructions shown, press the
POWER button to enter standby mode
temporarily.
4. After at least five minutes, press the POWER
button again.
The projector has not
been on long enough
(less than about 40
seconds).
Network connections are not available until about 40
seconds after startup. Wait at least 40 seconds, and
then try to connect again. (P139)
Cause Countermeasure
Troubleshooting
204
■You Cannot Operate the Remote Control
Cause Countermeasure
Batteries are not
installed properly or they
have run out.
Check whether batteries are installed correctly. If
batteries are installed correctly, replace them with
new batteries. (P37)
You are operating the
remote control from the
outside of the remote
control operating range.
Check whether you are operating the remote control
within the remote control operating range of the main
unit of the projector. (P38)
There is an obstacle
between the projector
and the remote control.
Remove the obstacle between the infrared remote
receiver of the main unit of the projector and the
remote control or point the remote control in an
obstacle-free path.
You are operating the
remote control in an
unsuitable operating
environment.
Check whether the infrared remote receiver of the
main unit of the projector is exposed to direct sunlight
or strong light of lighting apparatus. (P38)
The channel setting of
the remote control does
not match the setting of
the projector.
Check whether the channel setting of the remote
control has been changed. You can check the
[Remote control channel] setting in the [System
settings] menu. (P119)
The key lock function is
preventing operation of
the remote control.
Check whether [Key lock] is enabled to disable the
remote control operation.
In the [System settings] menu, set [Key lock] to [Off].
(P118)
Light from the room
lights is entering the
infrared remote receiver.
Block the light.
205
Index
Index
Numerics
6-axis color adjust........................... 101
A
Adjusting keystone distortion ............ 67
Adjusting the volume......................... 74
Air filter............................................ 172
Ambient light ..................................... 99
AMX Device Discovery ................... 135
Analog PC......................................... 56
ANALOG PC-1 / DVI-I terminal......... 33
ANALOG PC-2 / COMPONENT input
terminal........................................... 33
ASPECT............................................ 66
Aspect ....................................... 65, 183
AUDIO IN terminal ............................ 33
AUDIO OUT terminal ........................ 33
Auto (Aspect) .................................... 65
Auto PC....................................... 58, 91
Auto PC Adjustment.......................... 58
B
Beep................................................ 122
BLANK .............................................. 72
Brightness ......................................... 98
C
Ceiling mounted........................ 41, 105
Connecting to AV equipment ............ 51
Contrast ............................................ 98
Corner Adjustment.................... 68, 166
Crestron RoomView........................ 135
D
D. ZOOM........................................... 75
Digital zoom ...................................... 35
Direct power on............................... 122
Display resolution (Preparing the
computer) ....................................... 57
DVI-I terminal ....................................33
Dynamic gamma .............................100
E
Edge blending .....................6, 109, 162
Effect of ambient light........................99
F
FREEZE ............................................72
G
Gamma .............................................98
H
HDBaseT.............................5, 120, 121
HDBaseT terminal.................33, 50, 51
HDMI terminal ...................................33
I
IMAGE...............................................71
Image adjustment........................78, 96
Image mode (Image quality) .............70
Information ................................78, 156
INPUT ...............................................56
Input settings...............................78, 90
Input signal select .............................56
Input terminal ....................................33
Install settings............................78, 104
K
Key lock...........................................118
KEYSTONE....................................... 67
Keystone ...........................................67
L
Lamp mode .....................................102
Lamp replacement ..................173, 176
LAN port ............................................33
206
Index
Language ........................................ 123
LED indicator ............................ 31, 198
Lens - Position ................................ 112
Lens shift........................................... 47
Logo display.................................... 118
M
Memory color correction ................. 100
Menu ................................................. 78
MUTE................................................ 74
Muting the sound .............................. 74
N
Network password .......................... 130
Network settings ....................... 78, 127
Networked Multi-Projection (NMPJ)
................................................. 6, 145
Noise reduction......................... 99, 100
O
OK..................................................... 36
Optical zoom ..................................... 60
P
Password ................................ 124, 125
PJLink ..................................... 134, 150
POWER ...................................... 53, 71
Power-Saving Settings...................... 73
Projecting from Multiple Projectors at
Once (Edge Blending).................. 162
Projector on..................................... 118
R
Rear projection.......................... 41, 105
Registration..................................... 107
Remote control.................... 35, 37, 119
Reset................................. 69, 103, 126
S
Screen aspect ...........................63, 183
Screen color ....................................113
Selecting a language.......................123
Setting display status ........................90
Sharpness .........................................98
Side control .......................................30
Signal type ......................................188
Slideshows ................................95, 161
Split-screen display .........................161
System settings.........................78, 116
T
Test pattern......................................187
Tracking.............................................92
True size (Aspect) .............................66
Turning on external monitor output
(preparing the notebook computer)
........................................................55
U
USB Port ...........................................33
V
VOL ...................................................74
W
WARNING indicator ..................31, 198
Z
Zooming part of an image .................75
207
Option
•Lamp
Part No.: RS-LP11
•Ceiling attachment
Part No.: RS-CL11
•Ceiling-mount pipe
(350 - 550 mm / 13.8 - 21.7 in)
Part No.: RS-CL08*
•Ceiling-mount pipe
(550 - 950 mm / 21.7 - 37.4 in)
Part No.: RS-CL09*
•Air filter
Part No.: RS-FL01
•Remote control
Part No.: RS-RC04
•Remote control
Part No.: RS-RC05
* Use the above materials to hang the projector from the ceiling. For details, refer to the
assembly and installation manual provided with the ceiling attachment.
©CANON INC.2017YT1-7505-001
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON U.S.A. INC.
One Canon Park, Melville, New York 11747, U.S.A.
For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON
CANON EUROPE LTD.
3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United Kingdom
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands