Chief FCA803 User Manual
Displayed below is the user manual for FCA803 by Chief which is a product in the TV Mounts category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
Above Cart/Ceiling Above Wall
Below Cart/Ceiling Below Wall
(FCA813 shown)
Fusion™ Small Above/Below Accessory Shelf
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA803/813
FCA803/813 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight mounted to
the FCA803/813 shelf does not exceed 2 lbs (0.9 kg).
WARNING: Use of this accessory will decrease the weight
capacity of the mounting system to which it is attached by the
combined weight of the accessory and all components
supported by this accessory! See Figure below for reference.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this accessory to support video equipment such as
televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
standard weight limit of mounting system -
(weight of FCA803/813 shelf + shelf components)
2 lbs (0.9 kg)
Installation Instructions FCA803/813
3
DIMENSIONS - FCA803
16.8-18.3
[426.7-464.8]
MAX RANGE
12.0-14.3
[304.8-363.2]
MIN RANGE
540.74
21.29
17.5-19.0
[444.5-482.6]
MAX RANGE
13.0-15.0
[330.2-381.0]
MIN RANGE
578.84
22.79
OVERALL MAX
424.67
16.72
OVERALL MIN
CENTER OF MOUNT
104.76
4.12
FUSION WALL ABOVE MOUNT SETUP
15.6-18.2
[396.2-462.3]
MAX RANGE
11.2-13.7
[284.5-348.0]
MIN RANGE
592.56
23.33
OVERALL MAX
415.42
16.36
OVERALL MIN
CENTER OF MOUNT
133.35
5.25
16.7-19.2
[424.2-487.7]
MAX RANGE
578.84
22.79 12.2-14.2
FCA803/813 Installation Instructions
4
DIMENSIONS - FCA813
892.56
35.14
670.70
26.41 19.0 - 21.7
27.9 - 29.4
[708.7 - 746.8]
MAX RANGE
20.6 - 22-3
[523.2 - 566.4]
MIN RANGE
878.85
34.60
892.56
35.14
593.71
23.37
18.3 - 20.0
878.85
34.60
28.0 - 31.0
[711.2 - 787.4]
MAX RANGE
Installation Instructions FCA803/813
5
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
#2
3/8”
5/32” (included)
1/8” (included)
A (1)
[Upright bracket]
B (1)
[Main bracket]
J (3)
1/4-20 x 1/2”
C (2)
[Shelf bracket]
F (4)
E (1)
[Center washer]
[Large washer]
G (1)
H (5)
K (1)
1/4-20 X 5/8”
5/32”
P (1)
1/4-20 x 1/4”
[Small washer]
L (1)
1/4-20 x 3/8”
Q (1)
1/8”
N (4)
1/4-20 x 7/16”
M (4)
1/2”
D (1)
[Shelf]
FCA803/813 Installation Instructions
6
ASSEMBLY AND INSTALLATION
Below Installation
NOTE: FCA803 and FCA813 shelves may be installed above
or below displays. To install above display, proceed to
“Above Installation” Section.
Assembling Shelf to Upright Bracket
1. Loosely install two 1/4-20 x 1/2” button head cap screws (J)
into lowest holes on upright bracket (A). (See Figure 1) or
(See Figure 2)
2. Hang shelf support (D) onto two screws installed in Step 1.
(See Figure 1) or (See Figure 2)
3. Tighten two screws to ensure upright bracket (A) is securely
attached to shelf support (D). (See Figure 1) or (See
Figure 2)
Figure 1
Figure 2
Attaching Shelf to Wall Mount
NOTE: If attaching to cart or ceiling mount, proceed to Attach
Shelf to Cart/Ceiling Section.
1. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 3)
CAUTION: Slide bracket with caution so that the bracket
does not scratch or damage the wall!
2. Slide main bracket (B) behind wall mount rails until shelf
bracket (C) rests on top of wall mount rail. (See Figure 3)
Figure 3
3. Slide second shelf bracket (C) underneath lower rail on wall
mount, lining up holes on shelf bracket (C) to main bracket
(B). (See Figure 4)
4. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 4)
Figure 4
(J) x 2
1
2
2
(D)
(A)
3
tighten
(Below Wall)
(J) x 2
1
2
2
(D)
(A)
3
tighten
(Below Cart/ceiling)
2
(H) x 2
1
(F) x 2
(B)
(C)
(Below Wall)
3
wall mount rails
4
(H) x 2
(C)
(F) x 2
(B)
(Below wall)
Installation Instructions FCA803/813
7
NOTE: Refer to Table 1 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 1: Below Wall Mount
NOTE: Minimum and maximum configurations are shown
below. Intermediate configuration is the same.
5. Use 1/4-20 x 5/8” hex head flange bolt (K) and center
washer (E) to secure upright bracket (A) to main bracket (B).
(See Figure 5)
Figure 5
Attaching Shelf to Cart/Ceiling Mount
IMPORTANT ! : If installing to a 2x1 display cart using
the FCA623 accessory, proceed to “Installing to FCA623
Accessory” Section (Step 6).
1. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 6)
2. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 6)
Figure 6
3. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 7)
4. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 7)
Figure 7
5. Proceed to Step 11.
Extension distance from center of
mount (in.)
12.0-14.3 Minimum (FCA803)
14.3-16.8 Intermediate (FCA803)
16.8-18.3 Maximum (FCA803)
19.0-21.7 Minimum (FCA813)
21.7-26.9 Intermediate (FCA813)
26.9-28.4 Maximum (FCA813)
(B)
(K)
5
(Below wall - minimum)
(A)
(FCA813 shown)
(E)
(Below wall - maximum)
(B)
(K)
5
(A)
(E)
(rear view)
(C)
2
(H) x 2
1
(F) x 2
(B)
(Below cart/ceiling - Standard)
(rear view)
(C)
(H) x 2
4
(F) x 2
3
(B)
(Below cart/ceiling - Standard)
FCA803/813 Installation Instructions
8
Installing to FCA623 Accessory
IMPORTANT ! : Steps 6-10 only apply if installing to
FCA623 accessory.
6. Use two 1/4-20 x 7/16” button head cap screws (N), two
large washers (F) and two 1/2” spacers (M) to secure shelf
bracket (C) to main bracket (B). (See Figure 8)
7. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 8)
Figure 8
8. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 9)
9. Slide two 1/2” spacers (M) in between shelf bracket (C) and
main bracket (B). (See Figure 9)
10. Use two 1/4-20 x 7/16” button head cap screws (N) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 9)
Figure 9
NOTE: Refer to Table 2 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 2: Below Cart/Ceiling Mount
11. Use 1/4-20 x 5/8” hex head flange bolt (K) and center
washer (E) to secure upright bracket (A) to main bracket (B).
(See Figure 10)
NOTE: Maximum configuration is shown below. Several
intermediate configurations are possible depending on
which holes are used.
Figure 10
(rear view)
(C)
7
(H) x 2
6
(F) x 2
(B)
(Below cart with FCA623 accessory)
(M) x 2
(rear view)
(C)
(N) x 2
10
(M) x 2
8
(B)
(Below cart with FCA accessory)
(F) x 2
9
Extension distance from center of
mount (in.)
11.2-13.7 Minimum (FCA803)
13.7-15.6 Intermediate (FCA803)
15.6-18.2 Maximum (FCA803)
18.3-20.0 Minimum (FCA813)
20.0-26.7 Intermediate (FCA813)
26.7-30.0 Maximum (FCA813)
(K)
11
13
(FCA813 shown)
(rear view)
(A) (B)
(E)
(Below Cart/Ceiling Minimum)
(E)
(A)
(B)
(K)
11
(E)
(A)
(B)
(Below Cart/Ceiling Maximum)
Installation Instructions FCA803/813
9
Above Installation
Assembling Shelf to Upright Bracket
1. Install two 1/4-20 x 1/2” button head cap screws (J) into
lowest holes on upright bracket (A). (See Figure 11) or (See
Figure 12)
2. Hang shelf (E) onto two screws installed in Step 1. (See
Figure 11) or (See Figure 12)
3. Secure upright bracket (A) to shelf (E) using:
• 1/4-20 x 1/4” button head cap screw (H) if
installing to wall mount. (See Figure 11)
• 1/4-20 x 1/2” button head cap screw (J) if
installing to cart/ceiling mount. (See Figure 12)
4. Tighten all three screws to ensure shelf is secure.
Figure 11
Figure 12
Attaching Shelf to Wall Mount
1. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 13)
CAUTION: Slide bracket with caution so that the bracket
does not scratch or damage the wall!
2. Slide main bracket (B) behind wall mount rails until shelf
bracket (C) rests on top wall mount rail. (See Figure 13)
Figure 13
3. Slide second shelf bracket (C) underneath lower rail on wall
mount, lining up holes on shelf bracket (C) to holes on main
bracket (B). (See Figure 14)
4. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 14)
Figure 14
(J) x 2
1
3
(H)
2
2
(Above Wall)
(A)
(FCA813 shown)
(J) x 2
1
3
(J)
2
2
(Above Cart/ceiling)
(A)
(FCA813 shown)
2
wall mount rails
(H) x 2
1
(F) x 2
(C)
(B)
(Above wall - all)
3
(H) x 2
4
(F) x 2
(C)
(B)
(Above wall - all)
FCA803/813 Installation Instructions
10
NOTE: Refer to Table 3 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 3: Above Wall Mount
NOTE: Minimum and maximum configurations are shown
below. Intermediate configuration is the same.
5. Use 1/4-20 x 5/8” hex head flange bolt (K) and center
washer (E) to secure upright bracket (A) to main bracket (B).
(See Figure 15)
Figure 15
Attaching Shelf to Cart/Ceiling Mount
IMPORTANT ! : If installing to a 2x1 display cart using
the FCA623 accessory, proceed to “Installing to FCA623
Accessory” Section (Step 6).
1. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 16)
2. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 16)
Figure 16
3. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 17)
4. Use two 1/4-20 x 1/4” button head cap screws (H) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 17)
Figure 17
5. Proceed to Step 11.
Extension distance from center of
mount (in.)
13.0-15.0 Minimum (FCA803)
15.0-17.5 Intermediate (FCA803)
17.5-19.0 Maximum (FCA803)
20.6-22.3 Minimum (FCA813)
22.3-27.9 Intermediate (FCA813)
27.9-29.4 Maximum (FCA813)
(B)
(K)
5
(Below wall - minimum)
(A)
(FCA813 shown)
(E)
(Below wall - maximum)
(B)
(K)
5
(A)
(E)
(H) x 2
(F) x 2
1
(B)
2
(Above cart/ceiling - Standard)
(C)
(rear view)
(H) x 2
4
(F) x 2
(C)
3
(B)
(Above cart/ceiling - Standard)
(rear view)
Installation Instructions FCA803/813
11
Installing to FCA623 Accessory
NOTE: Steps 6-10 only apply if installing to FCA623
accessory.
6. Use two 1/4-20 x 7/16” button head cap screws (N), two
large washers (F) and two 1/2” spacers (M) to secure shelf
bracket (C) to main bracket (B). (See Figure 18)
7. Slide main bracket (B) onto front of cart mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 18)
Figure 18
8. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 19)
9. Slide two 1/2” spacers (M) in between shelf bracket (C) and
main bracket (B). (See Figure 19)
10. Use two 1/4-20 x 1/2” button head cap screws (J) and two
large washers (F) to secure shelf bracket (C) to main
bracket (B). (See Figure 19)
Figure 19
NOTE: Refer to Table 4 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 4: Above Cart/Ceiling
NOTE: Maximum and minimum configurations are shown
below. Several intermediate configurations are
possible depending on which holes are used.
11. Use 1/4-20 x 5/8” hex head flange bolt (K) and center
washer (E) to secure upright bracket (A) to main bracket (B).
(See Figure 20) or (See Figure 21)
12. (For maximum/intermediate extension ONLY) Use two
1/4-20 x 1/2" button head cap screws (J) to secure upright
bracket (A) to main bracket (B). (See Figure 20)
Figure 20
Figure 21
(N) x 2
(F) x 2
6
(B)
7
(Above cart with FCA accessory)
(C)
(rear view) (M) x 2
(J) x 2
10
(F) x 2
(C)
8
(B)
(Above cart with
(rear view)
FCA623 accessory)
(M) x 2
9
Extension distance from center of
mount (in.)
12.2-14.2 Minimum (FCA803)
14.2-16.7 Intermediate (FCA803)
16.7-19.2 Maximum (FCA803)
22.7-24.2 Minimum (FCA813)
24.2-28.0 Intermediate (FCA813)
28.0-31.0 Maximum (FCA813)
(J) x 2
11
(B)
(A)
(K)
12
(Above cart/ceiling
(E)
(rear view)
- maximum/intermediate)
(FCA813 shown)
(K)
(Above cart/ceiling - minimum)
(rear view)
(E)
(B)
(A)
(FCA813 shown)
11
FCA803/813 Installation Instructions
12
Height Adjustment
1. Loosen hardware used to attach main bracket (B) to upright
bracket (A). (See Figure 22)
2. Adjust shelf height as desired. (See Figure 22)
NOTE: For all above display installations, it is recommended
that the shelf be positioned so that it rests on top of
display to help ensure an even mount.
3. Tighten hardware used to attached main bracket (B) to
upright bracket (A). (See Figure 22)
Figure 22
Installing Camera (not included)
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight
mounted on the
FCA803/813 does not exceed 2 lbs (0.9 kg)
.
NOTE: Screw mounting options will vary based upon camera
model.
1. Install 1/4-20 x 3/8” Phillips pan machine screw (L) through
mounting slot on shelf and into hole on bottom of camera.
(See Figure 23)
2. Route cable from camera towards back of shelf and down
behind the FCA803/813. (See Figure 23)
Figure 23
2
13
(Above Cart/Ceiling
shown as example)
(FCA813 shown)
13
(FCA813 shown)
1
(Q)
Camera
(example -
2
not included)
Installation Instructions FCA803/813
13
FCA803/813 Installation Instructions
14
Installation Instructions FCA803/813
15
FCA803/813 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-003090 Rev00
2018 Milestone AV Technologies
www.milestone.com
10/18