Chief FTRV User Manual
Displayed below is the user manual for FTRV by Chief which is a product in the Monitor Mounts & Stands category. This manual has pages.
Related Manuals
INSTALLATION INSTRUCTIONS
Small Flat Panel Tilt Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FTRV / FTR4100
FTRV / FTR4100 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8” (1.6cm). Do
not install drywall anchors into the seam between drywall
pieces.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the FTRV/FTR4100 mount does
not exceed 45 lbs (20.4 kg). Use with products heavier than
the maximum weight indicated may result in collapse of the
mount and its accessories causing possible injury.
WARNING: Watch for pinch points! Do NOT place fingers
in between moving parts!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
The FTRV/FTR4100 mounts are designed to
be mounted to a single 2" x 4" wood stud. If necessary, they may
be installed to a single 2" x 4" wood stud on one side and drywall
on the other side using the drywall anchors provided.
NOTE: The FTRV includes the Chief FSBV interface bracket.
NOTE: The FTR4100 includes the Chief FSB75100 interface
bracket.
--SAVE THESE INSTRUCTIONS--
Installation Instructions FTRV / FTR4100
3
DIMENSIONS
LEGEND
1.02
100mm
MOUNTING
1.52
75mm
MOUNTING
1.69
5.61
.25 x6
3.38
5.56
4.75
1.82
FACE TILTS
5
UP
15 DOWN
.50
4.00
2.50
4.00
.38
.99
1.38
1.88
2.38
DIMENSIONS: INCHES
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
FTRV / FTR4100 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/8" (wood stud)
3/8" (drywall)
A (1)
[FTR Assembly]
B (2)
10-24
[Hollow wall anchor]
C (4)
#10
D (2)
#10 x 2-1/2"
Installation Instructions FTRV / FTR4100
5
INSTALLATION
The FTR may be installed either centered on a single 2" x 4"
wood stud, or not centered on a single wood stud if anchored to
drywall (1/2” minimum thickness) on the other side. The FTR
allows a tilt range from 5° up to 15° down.
Install Mount Centered to Single Wood Stud
1. Determine approximate mounting location, keeping in mind
the display size.
2. Use a stud sensor to locate applicable wood stud. Mark
location with a pencil.
3. Level FTR assembly (A) at desired height and, using it as a
template, mark the location of upper and lower pilot holes.
Ensure marks are in the center of wood stud.
NOTE: Mount can provide ±1/2" of lateral shift by using mount
holes on either side of vertical center line.
WARNING: ELECTRICAL SHOCK HAZARD! Drilling into
electrical wires or cables can cause DEATH or SERIOUS
PERSONAL INJURY! ALWAYS make certain area behind
mounting surfaces is free of electrical wires and cables
before drilling or installing mount fasteners.
4. Drill 1/8" pilot holes. Ensure pilot holes are straight.
5. Fasten FTR to wood stud using two #10 x 2-1/2" Phillips head
screws (D) through two #10 washers (C), FTR assembly (A),
and drywall (not shown) and install into pilot holes. (See
Figure 1)
Figure 1
Install Mount to a Single Wood Stud and Drywall
WARNING: Drywall must be a minimum thickness of 1/2"
and a maximum thickness of 5/8". Do NOT install drywall
anchors into the seam between drywall pieces.
1. Determine approximate mounting location, keeping in mind
the display size.
2. Level FTR assembly (A) at desired height and, using it as a
template, mark the location of the four anchor holes (one in
each corner slot). Two holes must be centered on a single
wood stud.
WARNING: ELECTRICAL SHOCK HAZARD! Drilling into
electrical wires or cables can cause DEATH or SERIOUS
PERSONAL INJURY! ALWAYS make certain area behind
mounting surfaces is free of electrical wires and cables
before drilling or installing mount fasteners.
3. Drill 1/8" pilot holes in wood stud locations. Ensure pilot
holes are straight. (See Figure 2)
4. Drill 3/8" anchor holes in the other two marked locations.
Ensure holes are straight and completely through drywall.
(See Figure 2)
Figure 2
2
4
x 2
x 2
5
(D) x 2
(A)
(C)
3
x 2
4
x 2
x 4
2
1/8”
3/8”
FTRV / FTR4100 Installation Instructions
6
5. Gently tap anchor (B) into anchor hole. Anchor barbs
should be fully engaged in drywall. (See Figure 3) and (See
Figure 4)
Figure 3
6. Using Phillips screwdriver, tighten anchor screws until
anchors have fully collapsed against back side of drywall.
(See Figure 4)
NOTE: Anchor screw will feel tight until anchor begins to
collapse. Screw will then turn easier for many turns.
Screw will feel tight when anchor has fully collapsed.
Figure 4
7. Remove and retain anchor screws from anchors (B).
NOTE: Anchors (B) may come with small washers which may
be left on the screw or discarded. These small washers
do NOT replace #10 washers (C).
8. Insert anchor screws through two #10 washers (C), FTR
assembly (A) and install into collapsed anchors (B). (See
Figure 5)
9. Install two #10 x 2-1/2” Phillips tapping screws (D) through
two #10 washers (C), FTR assembly (A) and into wood stud.
(See Figure 5)
Figure 5
Install Display to Mount
NOTE: Proper interface must be attached to display. Follow
instructions included with interface assembly.
1. Open latching flag by rotating flag clockwise on FTR (A).
(See Figure 6)
Figure 6
(B) x 2
5
Drywall
Anchor barb
Anchor
Anchor not
collapsed collapsed
6
(B) x 2
(D) x 2
9
8
anchor screws x 2
(C) x 2
(B) x 2
(A)
(C) x 2
1
Latching
flag closed
Latching
flag open
Installation Instructions FTRV / FTR4100
7
2. Lift and maneuver display such that all mounting buttons fit
into openings on FTR (A). (See Figure 7)
3. Lower display firmly into place. Ensure each mounting
button has fully seated in the opening (See Figure 7)
4. Close latching flag by rotating flag counterclockwise on FTR
(A). (See Figure 7)
Figure 7
NOTE: Mounting buttons are shown in the 100mm x 100mm
pattern. FTR (A) will also accommodate a 75mm x
75mm pattern. (See Figure 8)
Figure 8
NOTE: An optional padlock may be used to secure latching flag
in place. (See Figure 9)
Figure 9
5. Connect cables to display as required.
Removing Display from Mount
1. Disconnect all cables from display.
2. Open latching flag by rotating flag clockwise on FTR.
3. Lift and maneuver display mounting buttons out of button
openings.
Adjusting Tilt
1. Loosen adjusting screws on each side of display (See
Figure 10).
2. Adjust tilt as desired.
3. Retighten adjusting screws.
Figure 10
23
Display
(A)
4
Latching
flag
Button location for
75mm x 75mm
pattern (4 places)
NOTE: Display not shown for clarity.
Button location
for 100mm x
100mm pattern
(4 places)
NOTE: Display not shown for clarity.
5° Tilt Up 15° Tilt Down
123
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
FTRV / FTR4100 Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002780 Rev00
2015 Milestone AV Technologies
www.chiefmfg.com
07/15