Chief FCA810K User Manual
Displayed below is the user manual for FCA810K by Chief which is a product in the Video Conferencing Accessories category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
Above Cart/Ceiling Above Wall
Below Cart/Ceiling
Below Wall
ConferenceSHOT
®
Fusion™Above/Below Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA810K
FCA810K Installation Instructions
2
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief®, ConferenceSHOT® and Fusion™ are registered
trademarks of Legrand AV Inc.
DEFINITIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary product designed to mount the projector or display.
ACCESSORY: An ACCESSORY is any product designed by
Chief® to complement the primary mounting system either by
mounting any supporting components or enhancing the
mounting capabilities of the primary mounting system.
COMPONENT: A COMPONENT is any secondary product
designed to be used with the accessory, i.e. speakers, CPU’s,
cameras, tablets, additional displays.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight mounted to
the FCA810K shelf does not exceed 10 lbs (4.5 kg).
WARNING: Use of this accessory will decrease the weight
capacity of the mounting system to which it is attached by the
combined weight of the accessory and all components
supported by this accessory! See Figure below for reference.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this accessory to support video equipment such as
televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
standard weight limit of mounting system -
(weight of FCA810K shelf + shelf components)
10 lbs (4.5 kg)
Installation Instructions FCA810K
3
DIMENSIONS - FCA810K
FCA810K Installation Instructions
4
DIMENSIONS - FCA810K (CONTINUED)
Installation Instructions FCA810K
5
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
#2
3/8”
5/32” (included)
1/8” (included)
A (1)
[Upright bracket]
B (1)
[Main bracket]
D (1)
[Camera bracket]
L (3)
1/4-20 x 1/2”
C (2)
[Shelf bracket]
J (2)
#10-24 N (4)
F (1)
[Center washer]
[Large washer]
K (1) P (5)
E (1)
1/4-20 X 5/8”
Q (1)
#10-32 x 3/8”
5/32”
U (1)
1/4-20 x 1/4”
[Small washer]
M (1)
1/4-20 x 3/8”
T (8)
1" adhesive
hook and loop
H (1)
[Adapter plate]
V (1)
1/8”
R (4)
1/4-20 x 7/16”
G (4)
1/2”
Hardware bag (1)
(not used)
W (2)
#10-32 x 3/8"
FCA810K Installation Instructions
6
ASSEMBLY AND INSTALLATION
Assembling Shelf to Upright Bracket
1. Attach camera bracket (D) to upright bracket (A) using two
1/4-20 x 1/2” button head machine screws (L). (See Figure
1) or (See Figure 2)
Figure 1
Figure 2
Below Installation
NOTE: FCA810K shelves may be installed above or below
displays. To install above display, proceed to “Above
Installation” Section.
Attaching Shelf to Wall Mount
NOTE: If attaching to cart or ceiling mount, proceed to Attach
Shelf to Cart/Ceiling Section.
1. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 3)
CAUTION: Slide bracket with caution so that the bracket
does not scratch or damage the wall!
2. Slide main bracket (B) behind wall mount rails until shelf
bracket (C) rests on top of wall mount rail. (See Figure 3)
Figure 3
3. Slide second shelf bracket (C) underneath lower rail on wall
mount, lining up holes on shelf bracket (C) to main bracket
(B). (See Figure 4)
4. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 4)
Figure 4
NOTE: Refer to Table 1 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 1: Below Wall Mount
(L) x 2
1
(D)
(A)
(To Cart/Ceiling Mount)
(L) x 2
1
(D)
(A)
(To Wall Mount)
Extension distance from center of mount (in.)
18.8-20.5 Minimum
20.5-30.3 Intermediate
30.3-31.8 Maximum
2
(P) x 2
1
(N) x 2
(B)
(C)
(Below Wall)
3
wall mount rails
4
(P) x 2
(C)
(N) x 2
(B)
(Below wall)
Installation Instructions FCA810K
7
5. (For maximum extension) Use #10-32 x 3/8” button head
cap screw (Q) and small washer (K) to secure adapter plate
(A) to main bracket (B). (See Figure 5)
6. (For maximum extension) Use two #10-24 lock nuts (J) to
secure upright bracket (A) to main bracket (B) and adapter
plate (H). (See Figure 5)
Figure 5
7. (For minimum/intermediate extension) Use two #10-24
lock nuts (J) to secure upright bracket (A) to main bracket
(B) and adapter plate (H). (See Figure 6)
NOTE: Minimum configuration is shown below. Several
intermediate configurations are possible depending on
which holes are used.
NOTE: Camera shelf (D) may need to be temporarily removed
in order to attach lock nuts (J) for minimum extension.
8. (For minimum/intermediate extension) Use 1/4-20 x 5/8”
hex head flange bolt (E) and center washer (F) to secure
upright bracket (A) to main bracket (B). (See Figure 6)
Figure 6
Attaching Shelf to Cart/Ceiling Mount
IMPORTANT ! : If installing to a 2x1 display cart using
the FCA623 accessory, proceed to “Installing to FCA623
Accessory” Section (Step 6).
1. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 7)
2. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 7)
Figure 7
3. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 8)
4. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 8)
Figure 8
5. Proceed to Step 11.
(Below wall - maximum)
(H)
(B)
(A)
(K)
(Q)
5
(J) x 2
6
(J) x 2
7
(B)
(A)
(E)
8
(Below wall - minimum)
(V)
(F)
holes to
use for intermediate
configurations
(rear view)
(C)
2
(P) x 2
1
(N) x 2
(B)
(Below cart/ceiling - Standard)
(rear view)
(C)
(P) x 2
4
(N) x 2
3
(B)
(Below cart/ceiling - Standard)
FCA810K Installation Instructions
8
Installing to FCA623 Accessory
IMPORTANT ! : Steps 6-10 only apply if installing to
FCA623 accessory.
6. Use two 1/4-20 x 7/16” button head cap screws (R), two
large washers (N) and two 1/2” spacers (G) to secure shelf
bracket (C) to main bracket (B). (See Figure 9)
7. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 9)
Figure 9
8. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 10)
9. Slide two 1/2” spacers (G) in between shelf bracket (C) and
main bracket (B). (See Figure 10)
10. Use two 1/4-20 x 7/16” button head cap screws (R) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 10)
Figure 10
NOTE: Refer to Table 2 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 2: Below Cart/Ceiling Mount
11. (For maximum/intermediate extension) Use two #10-24
lock nuts (J) to secure upright bracket (A) to main bracket
(B) and adapter plate (H). (See Figure 11)
NOTE: Maximum configuration is shown below. Several
intermediate configurations are possible depending on
which holes are used.
12. (For maximum/intermediate extension) Use 1/4-20 x 5/8”
hex head flange bolt (E) and center washer (F) to secure
upright bracket (A) to main bracket (B). (See Figure 11)
Figure 11
(rear view)
(C)
7
(R) x 2
6
(N x 2
(B)
(Below cart with FCA623 accessory)
(G) x 2
(rear view)
(C)
(R) x 2
10
(G) x 2
8
(B)
(Below cart with FCA accessory)
(N) x 2
9
Extension distance from center of mount (in.)
18.7-20.4 Minimum
20.4-28.6 Intermediate
28.6-32 Maximum
(J) x 2
11
(B)
(A)
(E)
12
(Below cart/ceiling - maximum)
(H)
(F)
holes to
use for intermediate
configurations
(rear view)
Installation Instructions FCA810K
9
13. (For minimum extension) Slide upright bracket (A) behind
main bracket (B). (See Figure 12)
14. (For minimum extension) Use 1/4-20 x 5/8” hex head
flange bolt (N) and center washer (F) to secure upright
bracket (A) to main bracket (B). (See Figure 12)
Figure 12
Above Installation
Attaching Shelf to Wall Mount
1. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 13)
CAUTION: Slide bracket with caution so that the bracket
does not scratch or damage the wall!
2. Slide main bracket (B) behind wall mount rails until shelf
bracket (C) rests on top wall mount rail. (See Figure 13)
Figure 13
3. Slide second shelf bracket (C) underneath lower rail on wall
mount, lining up holes on shelf bracket (C) to holes on main
bracket (B). (See Figure 14)
4. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 14)
Figure 14
NOTE: Refer to Table 3 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 3: Above Wall Mount
(N)
14
13
(rear view)
(Below Cart/Ceiling Minimum)
(A)
(B)
(F)
2
wall mount rails
(P) x 2
1
(N) x 2
(C)
(B)
(Above wall - all)
Extension distance from center of mount (in.)
18.8-20.5 Minimum
20.5-30.3 Intermediate
30.3-31.8 Maximum
3
(P) x 2
4
(N) x 2
(C)
(B)
(Above wall - all)
FCA810K Installation Instructions
10
5. (For maximum extension) Use #10-32 x 3/8” button head
cap screw (Q) and small washer (K) to secure adapter plate
(H) to main bracket (B). (See Figure 15)
6. (For maximum extension) Use two #10-24 lock nuts (J) to
secure upright bracket (A) to main bracket (B) and adapter
plate (H). (See Figure 15)
Figure 15
7. (For minimum/intermediate extension) Slide upright
bracket (A) in front of main bracket (B). (See Figure 16)
8. (For minimum/intermediate extension) Use 1/4-20 x 5/8”
hex head flange bolt (E) and center washer (F) to secure
upright bracket (A) to main bracket (B). (See Figure 16)
NOTE: Minimum configuration is shown below. Several
intermediate configurations are possible depending on
which holes are used.
Figure 16
Attaching Shelf to Cart/Ceiling Mount
IMPORTANT ! : If installing to a 2x1 display cart using
the FCA623 accessory, proceed to “Installing to FCA623
Accessory” Section (Step 6).
1. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 17)
2. Slide main bracket (B) onto front of cart/ceiling mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 17)
Figure 17
3. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 18)
4. Use two 1/4-20 x 1/4” button head cap screws (P) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 18)
Figure 18
5. Proceed to Step 11.
(H)
(K)
(A)
(B)
(J) x 2
6
(Q)
(Above wall -
5
maximum)
7
(F)
(A)
(B)
(E)
8
(Above wall - minimum)
(P) x 2
(N) x 2
1
(B)
2
(Above cart/ceiling - Standard)
(C)
(rear view)
(P) x 2
4
(N) x 2
(C)
3
(B)
(Above cart/ceiling - Standard)
(rear view)
Installation Instructions FCA810K
11
Installing to FCA623 Accessory
NOTE: Steps 6-10 only apply if installing to FCA623
accessory.
6. Use two 1/4-20 x 7/16” button head cap screws (R), two
large washers (N) and two 1/2” spacers (G) to secure shelf
bracket (C) to main bracket (B). (See Figure 19)
7. Slide main bracket (B) onto front of cart mount head
assembly until shelf bracket (C) rests on top of head
assembly. (See Figure 19)
Figure 19
8. Slide second shelf bracket (C) underneath head assembly,
lining up holes on shelf bracket (C) to holes on main bracket
(B). (See Figure 20)
9. Slide two 1/2” spacers (G) in between shelf bracket (C) and
main bracket (B). (See Figure 20)
10. Use two 1/4-20 x 1/2” button head cap screws (R) and two
large washers (N) to secure shelf bracket (C) to main
bracket (B). (See Figure 20)
Figure 20
NOTE: Refer to Table 4 and dimension drawings on pages 3-
4 to determine the extension level based on extension
distance from mount center.
Table 4: Above Cart/Ceiling
11. (For maximum/intermediate extension) Use two #10-24
lock nuts (J) to secure upright bracket (A) to main bracket
(B) and adapter plate (H). (See Figure 21)
NOTE: Maximum configuration is shown below. Several
intermediate configurations are possible depending on
which holes are used.
12. (For maximum/intermediate extension) Use 1/4-20 x 5/8”
hex head flange bolt (E) and center washer (F) to secure
upright bracket (A) to main bracket (B). (See Figure 21)
Figure 21
13. (For minimum extension) Slide upright bracket (A) behind
main bracket (B). (See Figure 22)
14. (For minimum extension) Use 1/4-20 x 5/8” hex head
flange bolt (E) and center washer (F) to secure upright
bracket (A) to main bracket (B). (See Figure 22)
Figure 22
(R) x 2
(N) x 2
6
(B)
7
(Above cart with FCA accessory)
(C)
(rear view) (G) x 2
(R) x 2
10
(N) x 2
(C)
8
(B)
(Above cart with
(rear view)
FCA623 accessory)
(G) x 2
9
Extension distance from center of mount (in.)
18.7-20.4 Minimum
20.4-28.6 Intermediate
28.6-33 Maximum
(G) x 2
11
(B)
(A)
(E)
12
(Above cart/ceiling
(H)
(F)
holes to use
for intermediate
configurations
(rear view)
- maximum)
(E)
14
13
(Above cart/ceiling - minimum)
(rear view)
(F)
(A)
(B)
FCA810K Installation Instructions
12
Height Adjustment
1. Loosen (or remove) hardware used to attach main bracket
(B) to upright bracket (A). (See Figure 23)
2. Adjust shelf height as desired. (See Figure 23)
NOTE: For all above display installations, it is recommended
that the shelf be positioned so that it rests on top of
display to help ensure an even mount.
3. Tighten hardware used to attached main bracket (B) to
upright bracket (A). (See Figure 23)
Figure 23
Installing Camera (not included)
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight
mounted on the
FCA800E does not exceed 10 lbs (4.5 kg)
.
1. Use two #10-32 x 3/8" Phillips pan machine screws (W) to
secure camera to bracket (D). (See Figure 24)
Figure 24
2
13
(Above Cart/Ceiling
shown as example)
1
Camera
(not included)
(W) x 2
(D)
Installation Instructions FCA810K
13
FCA810K Installation Instructions
14
Installation Instructions FCA810K
15
FCA810K Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
8800-003284 Rev00
2021 Legrand | AV
www.legrandav.com
04/2021