Chief FCAC3X1LB User Manual
Displayed below is the user manual for FCAC3X1LB by Chief which is a product in the Monitor Mount Accessories category. This manual has pages.
Related Manuals
I N S T A L L A T I O N I N S T R U C T I O N S
(FCAC3X1M)
Fusion Back Covers
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCAC SERIES
FCAC SERIES Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not use
this accessory to support video equipment such as
televisions or computer monitors.
--SAVE THESE INSTRUCTIONS--
Installation Instructions FCAC SERIES
3
DIMENSIONS
FCAC1L
FCAC1X
FCAC SERIES Installation Instructions
4
DIMENSIONS (CONTINUED)
FCAC2X1M
FCAC2X1L
Installation Instructions FCAC SERIES
5
DIMENSIONS (CONTINUED)
FCAC3X1M
FCAC3X1L
FCAC SERIES Installation Instructions
6
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions FCAC SERIES
7
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2 3/16"
A (1/1/1/1/1/1)
[Fabric cover]
B (0/0/1/1/1/1)
[LCM Upright adapter]
[Upright Adapter Kit] - (FCAC1LB ONLY)
#12-24 x 3/8"
5/16-18 x 3/4"
[Center joiner tube]
[Upright w/o flag] [Upright w/flag]
[Center frame]
[Outside frame]
[LCM upright]
(QUANTITIES SHOWN = FCAC1L/1X/2X1M/2X1L/3X1M/3X1L)
C (2/2/2/2/2/2)
D (0/1/2/2/3/3) E (0/1/1/1/1/1)
F (2/2/4/4/0/0)
G (8/8/12/12/16/16)
H (1)
J (1)
K (4) L (1)
3/16"
[FCAC1L cover shown)
M (0/0/0/0/2/2)
[Extension frame]
FCAC SERIES Installation Instructions
8
Assembly And Installation
IMPORTANT ! : The FCAC Series frames can be
assembled at a variety of widths in 2" increments using
any of the holes available in the center joiner tubes (F)
depending on display size and user preference. Holes
shown being used in the graphics throughout these
instructions are just as examples.
Frame Assembly
FCAC1L
1. Slide together two outside frames (C) and two center joiner
tubes (F). (See Figure 1)
Figure 1
2. Use four #12-24 x 3/8" Phillips tapping screws (G) to secure
outside frames (C) to center joiner tubes (F). (See Figure 2)
Figure 2
3. Use four #12-24 x 3/8" Phillips tapping screws (G) to secure
LCM upright (H) to two center joiner tubes (F). (See Figure
3)
Figure 3
4. Proceed to "Fabric Cover Installation" Section.
FCAC1X
1. Slide together two outside frames (C) and two center joiner
tubes (F). (See Figure 1)
2. Use four #12-24 x 3/8" Phillips tapping screws (G) to secure
two uprights (D and E) to two outside frames (C). (See
Figure 4)
Figure 4
3. Proceed to "Fabric Cover Installation" Section.
(C) x 2
(F) x 2
1
1
1
1
(C) x 2
(G) x 4
2
(F) x 2
3
(G) x 4
(H)
(F) x 2
2
(G) x 4
(E)
(D)
(C) x 2
Installation Instructions FCAC SERIES
9
FCAC2X1M/FCAC2X1L
1. Slide together two outside frames (C), four center joiner
tubes (F) and one center frame (B). (See Figure 5)
Figure 5
NOTE: If there are any possible obstructions on back of display
that could interfere with uprights (D and E) installation,
measure where they will occur so uprights can be
attached accordingly. Uprights (without flags) (D) may
be installed in either Step 2, Step 4 or into any available
holes on center joiner tubes (F) depending on
obstructions or user preference.
2. Use four #12-24 x 3/8" Phillips tapping screws (G) to secure
two uprights (without flags) (D) to outside frames (C). (See
Figure 6)
NOTE: Example shown (See Figure 6) is to assemble a
maximum length frame. Frame can be made shorter
and must be shorter for FCAC2X1M.
3. Use two #12-24 x 3/8" Phillips tapping screws (G) to secure
upright (with flag) (E) to center frame (B). (See Figure 6)
Figure 6
4. Use four #12-24 x 3/8" Phillips tapping screws (G) to secure
four center joiner tubes (F) to center frame (B). (See Figure
7)
Figure 7
5. Proceed to "Cover Installation" Section.
FCAC3X1M/FCAC3X1L
1. Slide together two outside frames (C), two extension frames
(M) and center frame (B). (See Figure 8)
Figure 8
(C) x 2
(F) x 2
(B)
1
1
1
1
1
1
1
1
2
(G) x 4
3
(G) x 2
(D)
(E)
(D)
(FCAC2X1L shown)
4
(G) x 4
(B)
(F) x 4
(C) x 2
(B)
1
11
11
11
1
(M) x 2
FCAC SERIES Installation Instructions
10
NOTE: If there are any possible obstructions on back of display
that could interfere with uprights (D and E) installation,
measure where they will occur so uprights can be
attached accordingly. Uprights without flags (D) can be
installed in Step 2 as shown or separately in any
available holes in extension frames (M).
2. Use six #12-24 x 3/8" Phillips tapping screws (G) to secure
three uprights (without flags) (D) to outside frames (C),
extension frames (M) and center frame (B). (See Figure 9)
NOTE: Example shown (See Figure 9) is to assemble a
maximum length frame. Frame can be made shorter
and must be shorter for FCAC3X1M.
3. Use two #12-24 x 3/8" Phillips tapping screws (G) to secure
upright (with flag) (E) to center frame (B). (See Figure 9)
Figure 9
Fabric Cover Installation
1. Wrap fabric cover (A) over assembled frame. (See Figure
10)
Figure 10
2. Wrap outside straps around outside vertical rails on frame.
(See Figure 11)
3. Fasten vertical straps within cover to ensure a snug fit over
frame. (See Figure 11)
Figure 11
Installation to Display Mount
FCAC1L
1. Use four 5/16-18 x 3/4" button head cap screws (K) to
secure LCM upright adapter (J) to back of LCM mount. (See
Figure 12)
Figure 12
2
(G) x 6
3
(G) x 2
(FCAC3X1L shown)
(D) x 3
(E)
1
1
1
1
1
(FCAC2X1M shown)
2
3
(FCAC2X1M shown)
1
(K) x 4
(J)
LCM mount
Installation Instructions FCAC SERIES
11
2. Make sure mounting flag on LCM upright (H) is in the "open"
position. (See Figure 13)
3. Hang LCM upright (H) onto mounting buttons on back of
LCM upright adapter (J). (See Figure 13)
4. Move mounting flag on LCM upright to the "closed" position.
(See Figure 13)
Figure 13
FCAC1X/FCAC2X1M/FCAC2X1L/
FCAC3X1M/FCAC3X1L
1. Lift assembled cover onto top edge of mounting rail. (See
Figure 14)
Figure 14
2. Pull down mounting flag and pull under lower edge of
mounting rail. (See Figure 15)
3. Release mounting flag to secure cover to rail. (See Figure
15)
Figure 15
(Fabric cover hidden for clarity)
mounting flag
2
(open position)
3
3
(J)
(H)
4
(Fabric cover hidden for clarity)
1
1
1
1
mounting flag
3
2
(Fabric cover hidden for clarity)
FCAC SERIES Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-003061 Rev00
2018 Milestone AV Technologies
www.milestone.com
10/18